Smart-AVI HDMV-16X-PLUS (V3) Quick Start Guide

TECHNICAL SPECIFICATIONS

VIDEO

Format Single-link 340MHz [10.2Gbps]

Maximum Pixel Clock 165 MHz

Input Interface (16) HDMI

Output Interface HDMI

Resolution 800 x 600 up to 1920 x 1200

DDC

Input Equalization

Input Cable Length

5 volts p-p (TTL)

Automatic

Up to 20 ft.

Output Cable Length Up to 20 ft.

USB

Signal Type

Input Interface

Output Interface

USB 2.0, 1.1, and 1.0 w/ internal hub

(1) 3.5 mm Stereo Audio

(2) USB 1.1 Type A (female) for keyboard/mouse

AUDIO

Input (2) 3.5 mm Stereo Audio

Output (1) 3.5 mm Stereo Audio

POWER

Power Requirements

12V DC, 3A power adapter with center-pin positive polarity

ENVIRONMENT

Operating Temp 23 to 95°F (-5 to 35°C)

Storage Temp -4 to 185 °F (-20 to 85 °C)

Humidity

CONTROL

Front Panel

Up to 95% (non-condensing)

Push Buttons with LED indicators

RS-232

Hot Keys

OTHER

Emulation

Via Serial @ 9600 bps

Via Keyboard

Keyboard, Mouse and Video

WHAT’S IN THE BOX

PART NO.

HDMV16X-PLUS

PS12VDC3A

QTY DESCRIPTION

1

1

16-Port HDMI, USB Real-Time

Multiviewer and KVM Switch.

12V DC, 3A power adapter with center-pin positive polarity.

1 Quick Start Guide

NOTICE

The information contained in this document is subject to change without notice. SMART-AVI makes no warranty of any kind with regard to this material, including but not limited to, implied warranties of merchantability and fitness for particular purpose.

SMART-AVI will not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance or use of this material. No part of this document may be photocopied, reproduced, or translated into another language without prior written consent from

SMART-AVI, Inc.

Toll Free: (800) AVI-2123

Phone: (702) 800-0005

2455 W. Cheyenne Ave, Suite 112

North Las Vegas, NV 89032 smartavi.com

HDMV-16X-PLUS

16-Port HDMI KVM Multiviewer

16-PORT HDMI 1080P

REAL-TIME MULTIVIEWER

Quick Start Guide

A full Manual can be downloaded from www.smartavi.com/hdmv-16x-plus-v3/

SYSTEM CONTROL

There are three ways to control the

HDMV-16X-PLUS: Keyboard HotKeys, RS-232

Serial Commands, and Front Panel Buttons.

The settings for the serial connection are as follows: Baud rate: 9600; Data Bits: 8; Parity: None; Stop Bits: 1; Flow Control: None.

The following commands can be used:

Command HotKey RS-232

Switch KVM

[CT][CT] m [#]<CR> // M [#]<CR>

Video Only

[CT][CT] i

[#]<CR>

// I [#]<CR>

Full Screen

Mode

[CT][CT] x 1 <CR> // X1 <CR>

Quad Mode

[CT][CT] x 2 <CR> // X2 <CR>

16X Mode

[CT][CT] x 3

<CR>

// X3 <CR>

Borders ON

[CT][CT] b 1 <CR>

-

Borders OFF

[CT][CT] b 0 <CR>

-

Status // ??

<CR>

Chart Key

[CT] = Ctrl

<CR> = Carriage Return (Enter Key)

HARDWARE INSTALLATION

1. Ensure that power is turned off or disconnected from the unit and the computers.

2. Use HDMI cables to connect the HDMI output ports from each computer to the corresponding HDMI-I IN ports of the unit.

3. Use a USB cable (Type-A to Type-B) to connect a USB port on each computer to the respective USB ports of the unit.

4. Connect monitors to the HDMI-I OUT console ports of the unit using HDMI cables.

5. Connect a USB keyboard and mouse in the two USB console ports.

6. Optionally connect stereo speakers to the AUDIO OUT port of the unit.

7. Finally, power on the KVM by connecting a 12VDC power supply to the power connector, and then turn on all the computers.

Note: You can connect up to 16 computers to the 16 port KVM.