Digital Watchdog DWC-PVF9Di2TW MEGApix® Pano™ 9MP vandal fisheye IP camera User's Manual

PDF Download

Document

MEGApix ®

Pano TM 9 MP V

andal

Dome Fisheye

IP

amera

DWCPVF9Di2TW

User’s Manual

Ver. 0 6/ 20

Before installing and using the camera, please read this manual carefully.

Be sure to keep it handy for future reference.

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION :

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE

PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

Warning

This symbol indicates that dangerous voltage consisting of a risk of electric shock is present within this unit.

WARNING

To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture.

WARNING

1. Be sure to use only the standard adapter that is specified in the specification sheet. Using any other adapter could cause fire, electrical shock, or damage to the product.

2. Incorrectly connecting the power supply or replacing the battery may cause an explosion, fire, electric shock, or damage to the product.

3. Do not connect multiple cameras to a single adapter.

Exceeding the capacity may cause excessive heat generation or ﬁre.

4. Securely plug the power cord into the power receptacle. An insecure connection may cause ﬁre.

5. When installing the camera, fasten it securely and ﬁrmly. A falling camera may cause personal injury.

6. Do not place conductive objects (e.g. screwdrivers, coins, metal items, etc.) or containers ﬁlled with water on top of the camera. Doing so may cause personal injury due to ﬁre, electric shock, or falling objects.

7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause ﬁre or electric shock.

8. If any unusual smells or smoke come from the unit, stop using the product. Immediately disconnect the power source and contact the service center. Continued use in such a condition may cause ﬁre or electric shock.

9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way.

10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause ﬁre or electric shock.

Precaution

This exclamation point symbol is intended to alert the user to the presence of important operating and maintenance

(servicing) instructions in the literature accompanying the appliance.

Precaution

Operating

• Before using, make sure the power supply and all other parts are properly connected.

• While operating, if any abnormal condition or malfunction is observed, stop using the camera immediately and contact your dealer.

Handling

• Do not disassemble or tamper with parts inside the camera.

• Do not drop the camera or subject it to shock or vibration as this can damage the camera.

• Clean the clear dome cover with extra care. Scratches and dust can ruin the quality of the camera image.

Installation and Storage

• Do not install the camera in areas of extreme temperature, exceeding the allowed range.

• Avoid installing in humid or dusty environments.

• Avoid installing in places where radiation is present.

• Avoid installing in places where there are strong magnetic fields and electric signals.

• Avoid installing in places where the camera would be subject to strong vibrations.

• Never expose the camera to rain or water.

Important Safety Instructions

1. Read these Instructions.

- All these safety and operating instructions should be read before the product is installed or operated.

2. Keep these Instructions.

- The safety, operating and use instructions should be retained for future reference.

3. Heed all warnings.

- All warnings on the product and in the operating instructions should be adhered to.

4. Follow all instructions.

- All operating and use instructions should be followed.

5. Do not use this device near water.

- For example: near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement; near a swimming pool; etc.

6. Clean only with a dry cloth.

- Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners.

7. Do not block any ventilation openings. Install following the manufacturer’s instructions.

- Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the product, and to protect it from overheating. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surfaces.

This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and the manufacturer’s instructions have been adhered to.

8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Disposal of Old Appliances

1. When this crossed-out wheel bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream per laws designated by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Introduction

Product and accessories..................................................................................................................................................................5

Parts identification............................................................................................................................................................................6

Installation

Disassembl ing the camera........................................................................................................................

....................................7

Factory reset....................................................................................................................................................

...................................7

Installation........................................................................................................................................................

..................................8

Cabling.............................................................................................................................................................

..................................1

Managing the SD Card..................................................................................................................................................................13

Network Setup

DW IP finder.............................................................................................

........................................................................................1

Web Viewer

Login to the camera.......................................................................................................................................................................1

GUI overview.....................................................................................................................................................................................1

Camera Settings

Settings > Video and audio setup.............................................................................................................................................1

Settings > Camera setup > Image adjustment.....................................................................................................................2

Settings > Camera setup > Exposure settings......................................................................................................................2

Settings > Camera setup > Day and night settings............................................................................................................2

Settings > Camera setup > Backlight settings......................................................................................................................2

Settings > Camera setup > White Balance settings............................................................................................................2

Settings > Camera setup > Image enhancement settings...............................................................................................

Settings > Camera setup > Video enhancement.................................................................................................................

Settings > Network setup.............................................................................................................................................................

Settings > Trigger action setup..................................................................................................................................................

Settings > Event setup........................................................................................................................................................

..........4

Settings > Record setup................................................................................................................................................................51

Settings > Security setup..............................................................................................................................................................

Settings > System setup > System information...................................................................................................................

Settings > System setup > Firmware.......................................................................................................................................

Settings > System setup > Date and time..........................................................................................................................

...

Settings > System setup > DST..................................................................................................................................................

Settings > System setup > Users...............................................................................................................................................

Settings > System setup > System log....................................................................................................................................

Settings > System setup > Factory reset................................................................................................................................

Settings > System setup > Restart............................................................................................................................................

Settings > System setup > System open source license...................................................................................................

Network setup guides...............................................................................................................................

FAQs............................................................................................................................................................

Dimensions.................................................................................................................................................

Specifications.............................................................................................................................................

Warranty.....................................................................................................................................................

Limits and exclusions...................................................................................................................

.............

Introduction -

Product and Accessories

Camera

Cables

Hex Allen Wrench Screws and

Plastic Anchors - 3pcs

Mounting Plate

Mounting Template for Bolt and Nut

Installation

Mounting Template for

Plate Installation

Mounting Bolts and Nuts

Waterproof Cap and

Gasket

Quick Setup and

Installation Guides

Introduction -

Part Names

Illumination Sensor Hall

Dome Cover

Illumination Sensor

Alarm In/Out

Audio In/Out

Waterproof Cap

DC Power Jack

RJ-45 Connector

Mounting Plate

Plate Hook

Window Cover

Fisheye Lens

SD Card Slot

Reset Button

Installation -

Disassembling the Camera

Before installing your camera, you have to read the following cautions.

1. The mounting surface must withstand ﬁve times the camera weight.

2. Do not let the cables get caught in improper places or the electric line cover can be damaged. This may cause a short or ﬁre.

3. For the installation process, remove the camera cover from the camera module by loosening the three (3) screws on the dome. Use the wrench provided with the camera.

The camera includes a sensor at the camera module.

For the sensor to function properly, the camera’s cover includes a special sensor hole.

When assembling the camera together, please make sure the sensor hole in the camera’s cover is aligned with the sensor in the camera module.

When placing the cover back on the camera, also make sure to align the cover and bottom case to match the case outline.

Reset to the Factory Default

Press the reset button for 5 seconds to return the

setup to the factory default.

Warning:

If you press the ‘Reset’ button, you will lose all

setting data. If needed, please, make a note for

further installation.

Reset Button

Installation -

Basic Installation

Mounting Template

1. Using the mounting template sheet or the camera itself, mark and drill the necessary holes in the wall or ceiling.

2. Pass the wires through the mount bracket and make all necessary connections. See page 12 for more information.

3. To use the camera’s waterproof wiring: a. Install the LAN cable into (a) .

b. (b) will be assembled to (a) with a 1/4 turn.

c. Thread (c) tightly to (b).

c a b

NOTE: to ensure a proper moisture seal, make sure the o-ring is in place between (a) and (b). In extreme environments, use an outdoor-rated sealer.

NOTE: When using the waterproof cap, crimp the RJ-45 connected after passing the camera through the waterproof cap.

4. Attach the camera to the mounting surface using the included anchors and screws.

5. Assemble the cover over the camera body. Be sure to assemble the cover and bottom case to match the case outline.

6. When the installation is completed, remove the protective film.

Installation -

Installation Using Mounting Plate

Template Sheet

1. Using the mounting template sheet for the metal plate, or the metal plate itself, mark and drill the necessary holes in the wall or ceiling.

2. Pass the wires through the mount bracket and make all necessary connections. See page 12 for more information.

3. To use the camera’s waterproof wiring: a. Install the LAN cable into (a) .

b. (b) will be assembled to (a) with a 1/4 turn.

c. Thread (c) tightly to (b).

5 a b

NOTE: to ensure a proper moisture seal, make sure the o-ring is in place between (a) and (b). In extreme environments, use an outdoor-rated sealer.

NOTE: When using the waterproof cap, crimp the RJ-45 connected after passing the camera through the waterproof cap.

4. Mount the metal plate to the mounting surface using the included screws.

5. Assemble the cover over the camera body. Be sure to assemble the cover and bottom case to match the case outline.

6. Fix the camera's bottom case to the metal plate. Press the three (3) bezels on the bottom care of the camera until it snaps to the metal plate. A snap sound will confirm the camera base is properly locked into the mounting plate.

7. When the installation is completed, remove the protective film.

Installation -

Installation Using Mounting Bolts and Nuts

1. Using the mounting template for the nuts and bolts installation, mark and drill the necessary holes in the wall or ceiling.

2. Pass the wires through and make all necessary connections. See page 12 for more information.

3. Secure the two long mounting screws to the camera’s base.

4. Mount the camera to the mounting surface using the 2 mounting nuts.

5. Rotate the locking discs over the screws until the camera is held tightly from the mounting surface.

6. Adjust the camera’s lens position to the necessary angle. the camera’s max tilting angle is 75°.

7. Assemble the dome cover over the camera body.

Be sure to assemble the dome and bottom case to match the case outline.

8. When the installation is completed, remove the protective film.

Installation -

Cabling

Two Options

Use a PoE-enabled switch to connect data and power through a single cable and begin viewing and recording images instantly.

A non-PoE switch will require an adaptor for power transmission.

1. Using a PoE-Enabled Switch

The Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable.

PoE eliminates the need for the different cables used to power, record, or control the camera. Follow the illustration below to connect the camera to a PoEenabled switch using an Ethernet cable.

2. Using a Non-PoE Switch

If a PoE-enabled switch is not used, use a power adaptor for power transmission and non-PoE switch for data transmission.

Follow the illustrations below to connect the camera without a PoE-enabled Switch.

Ethernet cable

Power

Ethernet cable

Installation -

Cabling

Alarm In/Out

Network

Audio Input

Audio Output

Power

Power Connection

Please, check the voltage and current capacity of rated power carefully.

Rate Power

DC 12V

Power

Consumption

8.5W

PoE

IEEE 802.3af class3, max 10W

Network Connection

Connect the crossover cable into the RJ-45.

Audio Output

Connect the ‘audio out’ port of the camera to the

‘line in’ port of the speaker.

If the speaker without the amplifier is connected

to the audio out port, it doesn’t work properly.

Therefore, the speaker with the amplifier or the

separate amplifier is needed.

Audio Out is available via the RTSP backchannel.

Audio Input

Connect the ‘audio in’ port of the camera to the

microphone directly or 'line out’ port of the

amplifier connected with a microphone.

If the microphone is connected directly, the

microphone with the embedded amplifier such

as condenser mic. needs to be used.

DI (+)

DI (-)

DO (-)

DO (+)

WHITE

YELLOW

SKY BLUE

GRAY +

DOT

Alarm/Relay Out (DO)

Connects to the alarm lights, siren or lamps and

the sensor types are normally open and

normally close.

Alarm Input

Alarm Output

Sensor/Alarm Input (DI)

The sensor/alarm input device's cable should

connect to + and - of the Terminal Block.

Installation -

Managing the SD Card

The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices.

Micro

Recommended SD card specification

(not included)

- Type: Micro SD (SD/SDHC/SDXC)

- Manufacturer: SanDisk, Samsung,

Transcend, Micron

- Capacity: 4GB~128GB

- Class: UHS-I U3 Class 10

New micro SD card over 64GB must be

formatted on the first use.

Inserting an SD Memory Card

Insert the SD card in the arrow direction.

Don’t insert the SD memory card while it’s

upside down by force. Otherwise, it may

damage the SD memory card.

Removing an SD Memory Card

Removing an SD Memory Card Gently press down

on the exposed end of the memory card as shown

in the diagram to eject the memory card from

the slot.

Pressing too hard on the SD memory card can

cause the card to shoot out uncontrollably from

the slot when released.

If you have saved data in the SD memory card,

removing the SD memory card before setting

the record to OFF will cause damage to the data

stored in the card.

Network setup -

DW IP Finder

Thumbnail view

Select network to scan

Filter device type to scan

Scan devices

Show/hide

Refresh thumbnail view

Bulk IP assignment

Firmware upgrade

Go to: http://www.digital-watchdog.com and search for

‘IP Finder’ on the quick search bar at the top of the page.

The latest IP Finder software will appear in the search results. Click on the link to download the file to your computer.

The software will scan your network for all supported cameras and display the results in the table. Allow up to 5 seconds for the IP Installer to find the camera on the network.

You can press the ‘Refresh List’ to search the network again, or filter the search results by entering a value in the filter box.

Check the box next to ‘Display Camera Thumbnail’ to view a JPEG image of the camera’s view next to the camera name on supported models.

i i

The default network type of camera is DHCP mode.

If you have a DHCP server, it will automatically set the

Camera IP.

Contact your network administrator for more information.

To save the changes made to the camera's settings, input

ID and PW of the camera for authentication.

If the camera needs to be rebooted after the settings were changed, press the 'Reboot' button. The camera will power cycle and will appear back in the search results once the reboot is complete.

Default ID / PW : admin / admin i

For security purposes, it is highly recommended to change your password after initial setup .

Click 'Save' to save changed values.

To update the camera's firmware from the DW IP Finder

, click on the firmware tab, upload the firmware file and select the camera to update. You can update multiple cameras at the same time.

Firmware version

Camera's uptime

Open device configuration settings

Device's information

Web Viewer Screen -

Basic Screen (Default)

Password change is required at the initial connection in a factory reset state.

You cannot see the image, and the setup button is disabled.

Change the password with the CHANGE PASSWORD button.

After changing the password, login again by pressing the RE-LOGIN button.

• Internet Explorer: After three failed attempts or the cancel button is clicked, you will experience a login fail.

• Other Browsers: After the Cancel button is clicked, you will experience a login fail.

Password Hint Page

• If you need help remembering the password for your user, input the username in the username field and press the hint button. If you added a hint for your password when setting it up, it will appear then.

Web Viewer Screen -

Basic Screen

The web viewer is optimized with Internet Explorer 10 (or above) and Mozilla Firefox.

“If VLC is not installed or the VLC plugin is not supported (Chrome), ‘Live Buffering’ and ‘Channel Select’

(subjects 3 and 4 in the diagram) will display as ‘Live Viewer’. If so, select HTML5 (MJPEG) from the Live

Viewer menu to view the video.

Live video display. This is the region for the live video stream from the camera.

Setup a popup button. Click it to open the Setup page to setup details of IP camera like Video, Network,

Events, System, etc. See the section ‘Setup’.

When the image is not smooth due to a bad network connection, it stored image during setup time and

shows the image on the live view screen.

Users will see the delayed images based on the set delay time.

Channel Select button. Select a stream produced from the camera between Stream 1 ~ 3 to display it in the live

view screen.

Refer the ‘Setup > Video & Audio > Video’ to setup the Video Stream.

Below “Menu” is supported per models.

PTZ Control -

This camera model does not support the zoom and focus.

Preset -

Not supported.

Speaker Control -

Enable/disable the audio stream from the camera and adjust the volume accordingly.

Alarm Input -

If an alarm is triggered, the corresponding input number will be changed from dark gray to red.

Relay Out -

Using this checkbox, read the relay output status and set or reset it manually.

Motion -

Shows the motion event status.

Event Alert Icon ( ) appears if ‘Motion Detection’ is activated.

Camera Time -

Display the camera time.

Setup - Video & Audio Setup

Video Configuration

Detail Page -

When you select an item from the menu, you can set the details for the selected item.

Setup Constitution

Video&Audio

[ VIDEO, OSD, ROI, AUDIO, PRIVACY MASK ]

Camera

[ IMAGE ADJUSTMENT, EXPOSURE, DAY&NIGHT, BACKLIGHT, WHITE BALANCE, IMAGE, VIDEO ]

Network

[ STATUS, NETWORK SETTING, AUTO IP, ONVIF, UPNP, DDNS, FTP, SMTP, SNMP, RTSP INFORMATION ]

Trigger Action

[ ACTION RULES, IMAGE TRANSFER, RELAY OUT ]

Events

[ EVENT RULES, MOTION, TEMPERATURE, ALARM ]

Record

[ MANAGEMENT, RECORD LIST, STORAGE ]

Security

[ IP ADDRESS FILTER, RTSP AUTHENTICATION, IEEE 802.1x, HTTPS, CERTIFICATES, SERVICE ]

System

[ INFORMATION, DIAGNOSTICS, FIRMWARE UPDATE, DATE&TIME, DST, USER MANAGEMENT, LOG,

LANGUAGE, FACTORY RESET, RESTART, OPEN SOURCE ]

Setup - Video & Audio Setup

Video Configuration

Live Video Channel Setup -

The video can be conﬁgured to various settings with a combination of codec and

resolution. The camera performance should be considered when setting multiple channels, as the performance

of the camera will be affected.

H.265 (HEVC) codec with higher bitrate may cause unstable live streaming or reload the webpage.

Codec -

Choose the video codec. Depending on the selected codec, the subcategories may be changed

accordingly.

Description -

Input the additional description of the selected channel. Max. 30 alpha-numeric characters may

be used, including spaces.

Resolution -

Select video resolution.

Available Frame Rate may differ even if the same codecs are in use.

NTSC

3K x 3K

3008 x

3000

7.8M

2800 x

2800

2.6M

1600 x

1600

0.4M

640 x

640

0.1M

320 x

320

PAL

3008 x

3000

2800 x

2800

1600 x

1600

640 x

640

320 x

320

Frame Rate -

Select the maximum Frame Rate.

Available Frame Rate can be diﬀerent although the same codecs were set up.

Setup - Video & Audio Setup

Video Configuration

GOP(Group of Pictures) Size -

Set up the number of frames (P-frame) which contain only changed information

based on the basic frame (I-frame). Regarding videos with lots of movement, if you set GOP size bigger, only

the number of P-frames is bigger.

As a result, the video resolution will be low but ‘File size’ and ‘Bit-rate can be decreased.

GOP(Group of Pictures) Size -

I-frame and P-frame creation for MPEG4, H.264, and H.265 (HEVC) video compression. ‘I-frame’, also known

as ‘key-frame’, refers to the complete image data for a specific video frame. ‘P-frame’ refers to the changes

in the image in comparison to the previous video frame. As a result, the GOP consists of one I-frame and

several P-frames. For improved video quality, use a lower number of P-frames for this setting.

Proﬁle -

The proﬁle deﬁnes the subset of bitstream features in H.264, H.265 (HEVC) stream, including color

reproduction and additional video compression.

H.264: Main, High / H.265 (HEVC): Main

Main -

An intermediate proﬁle with a medium compression ratio. Supports I-frames, P-frames, and B-frames.

High -

A complex proﬁle with a high compression ratio. Supports I-frames, P-frames, and B-frames.

Bitrate Mode -

Select the bit rate control scheme of video compression from CBR (Constant Bit Rate) or VBR

(Variable Bit Rate).

CBR -

To guarantee the designated constant bit rate, the quality of the video is controlled in this mode. Therefore, the quality of the video is likely to be varying when network traﬃc is changing.

VBR -

To guarantee the designated quality, the bit rate of the video stream is changed in this mode.

Therefore, the frame rate of the video is likely to be varying when network traﬃc is changing.

This category will not appear if you select the codec.

Setup - Video & Audio Setup

Video Configuration

Target Bitrate -

If Bitrate Control is set to be CBR, you can set the Target Bitrate.

Quality -

For VBR control mode, The Target Quality of video can be setup.

Smart Core -

Off / Smart.RC

Extension Option

Oﬀ -

You cannot use the Extension Option.

SVC-T On -

The H.264, H.265 (HEVC) SVC (Scalable Video Coding) is a video compression algorithm that enables effective and efficient transmission of video files over low bandwidth networks.

Click ‘Apply’ to save all settings.

Setup - Video & Audio Setup

OSD Configuration

Date / Time -

Display the current time.

User Text -

Output the TEXT entered by the user. Support a maximum of 30 characters.

Click ‘Apply’ to save all settings.

Setup - Video & Audio Setup

Region of Interest Configuration

The region of interest function gives a more efficient picture quality for the indicated area to improve the qualities of movement in the scene without compromising the bandwidth.

Stream -

Select the Stream.

Currently supports only H.264, H.265 (HEVC).

The function is not supported in the MJPEG codec.

Activation -

Enable or disable the region of interest function.

Quality -

Set the quality of the set area.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Setup - Video & Audio Setup

Audio Configuration

Codec -

Select the Audio Codec.

Currently, the camera supports codec G.711.

Volume -

Select the Audio Volume from 0 to 10.

Sample Rate -

Select the Audio Sample Rate.

Currently, the camera supports 8000 Hz.

Click ‘Save’ to save all changes.

Setup - Video & Audio Setup

Privacy Mask Configuration

Use this function to mask areas that you want to hide on-screen to protect privacy.

Activation -

Enable or disable the privacy mask function.

Area -

Select the Area1 ~ Area16 and Set the privacy area.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click ‘Clear Area' to delete the selected Area1~Area16.

Setup - Camera Setup

Camera Image Adjustment

Sharpness -

The higher the number, the sharper the lines in the image will appear.

Brightness -

The higher the number, the brighter the image will appear.

Contrast -

The higher the number, the stronger the contrast between colors in the image will appear.

Saturation -

The higher the number, the more saturated the colors in the image will appear.

Hue -

The higher the number, the stronger the hue in the image will appear.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Camera Setup

Camera Exposure Settings

Auto Exposure -

Automatic exposure (AE) automatically sets the aperture or shutter speed, based on the

external lighting conditions for the photo.

Exposure Level -

The higher the number, the brighter the image will appear.

AE metering -

AE metering mode refers to how a camera determines the exposure.

Shutter Speed -

If this speed is faster, the moving object can be photographed without the ghost effect.

However, the picture can be dark if the lighting is insufficient.

Slow Shutter Level -

Slow shutter Level lets you adjust the amount of light striking the sensor and essentially

determines when the video sensor sends out its batch of data for processing.

Gain Limit -

The smaller number makes the darker image.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Camera Setup

Camera Day & Night Settings

Day & Night

•

Auto:

In this mode, the IR cut filter is removed automatically depending on the light condition around.

•

Day:

In this mode, the IR cut filter is applied to the image sensor all the time. Thus, the sensitivity will be

reduced in the dark light condition, but the better color reproduction performance is obtained.

•

Night:

In this mode, the IR cut filter on the image sensor is removed all the time. The sensitivity will be

enhanced in the dark light condition, but the image is black and white.

•

Schedule:

In this mode, Day / Night mode is converted accordance with the scheduled time.

Color Level -

It is a level to change Night mode into Day mode when Day & Night mode is Auto.

B / W Level -

It is a level to change Day mode into Night mode when Day & Night mode is Auto.

Transition Time -

If it is set to Auto, to determine the rate at which Day / Night is converted.

If it is set to schedule mode, Set the time that Day / Night is converted.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Camera Setup

Camera Backlight Settings

This feature is used when lighting conditions may cause detail loss in the camera's view due to high contrast.

Digital-WDR -

Enable or disable the feature.

Click ‘Save’ to save all changes.

Click 'Cancel' to return to the previous setting.

Click 'Default' to change the settings back to their factory defaults.

Setup - Camera Setup

Camera White Balance

Activation -

Enable or disable the White Balance function

White Balance Mode -

Select White Balance depending on the lighting conditions.

RGB Gain -

The R/G/B gain can be set only when the White Balance Mode is set to Manual.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Camera Setup

Camera Image Enhancement

3D Noise Reduction -

3DNR function enables to suppress noise and retain good video quality in low light conditions.

Click ‘Save’ to save the current settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Camera Setup

Video Enhancement

Flicker -

In case of flickering video, adjust the flickering values in this menu.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Click 'Default' to settings to the factory defaults.

Setup - Network Setup

Network Status

This menu displays the camera's current network settings. To make any changes to the settings, you must go to the appropriate network settings tab.

Setup - Network Setup

Network Settings

Network Type -

Deﬁne the network IP address type. Select Static Mode for a ﬁxed IP or Dynamic Mode for a

dynamic IP address.

If you select Static Mode, enter the camera's IP Address, Subnet Mask, Gateway, DNS Server, and all ports.

If you select Dynamic Mode, the IP address will be assigned automatically by the DHCP network requirements.

If you click 'Apply', the system will reboot and you will have to reconnect the camera using the new IP address.

IP Address -

The camera's IP address consists of four numbers between 0 and 255, separated by dots.

Subnet Mask -

Deﬁne the Subnet Mask. The format is the same as the IP address.

Default Gateway -

Default the Gateway IP Address. The format is the same as the IP address.

Preferred DNS Server -

Deﬁne the DNS server IP address. The format is the same as the IP address.

Alternate DNS Server -

Deﬁne the Secondary DNS server IP address. The format is the same as the

IP address.

HTTP Port -

The HTTP port can be set to the default 80 port or any value in between 1025 to 60000.

HTTPS Port -

The HTTPS port can be set to the default 443 port or any value in between 1025 to 60000.

RTSP Port -

The RTSP port can be set to the default 554 port or any value in between 1025 to 60000.

Click ‘Apply’ to save all settings.

If the network type is dynamic, the IP address is changed in the following cases. In these cases, the IP address needs to be searched again, and the camera needs to be reconnected:

• When the camera's power is switched off and on.

• After firmware update, or when the camera is reset to its default settings and reboot.

Setup - Network Setup

Auto IP Settings

General Setting -

Enable or disable the Auto IP Settings.

Auto IP Settings Information -

Display the camera's Unique ID and Auto IP address.

Click ‘Apply’ to save all settings.

Setup - Network Setup

ONVIF Settings

Authentication

None:

Allow access to the camera without ONVIF authentication.

WS - Usertoken:

Allow access to the camera with WS-User Token of ONVIF authentication.

WS - Usertoken + Digest:

Allow access to the camera with WS-User Token and Digest of

ONVIF authentication.

Discovery Mode -

Enable or disable discovery mode.

Click ‘Apply’ to save all settings.

Setup - Network Setup

UPNP Settings

General Setting -

Enable or disable the UPNP function.

Friendly Name -

Define the friendly name. Support a maximum of 30 characters and special characters.

• Do not use: / ~ ! $ ( ) { } [ ] ; ,

• Acceptable special characters include; @ . _ -

Click ‘Apply’ to save all settings.

Setup - Network Setup

DDNS Settings

DDNS Disable -

If it is selected, DDNS service does not work.

Public DDNS -

To use public DDNS service, select a site address listed on the list. After ﬁlling out the

Host Name of the site the setup is completed by entering username and Password registered in that

DDNS site.

DDNS Provider

DynDNS

No-IP

If you setup DDNS properly, the IP address of your camera will be updated automatically whenever the IP

address is changed or the system is rebooted.

If IP updating to the DDNS site is failed, the camera will keep retrying in 1min. interval.

Click ‘Apply’ to save all settings.

Setup - Network Setup

FTP Settings

To transfer/save the image to the relevant sites through FTP, then FTP needs to be setup.

General Setting -

Enable or disable the FTP function.

FTP Server Address -

Deﬁne FTP Server IP Address. If the IP Address form is incorrect, a message box will be

shown to try again.

FTP Upload Path -

Deﬁne a path in FTP server to store video. For the path name, English Alphabets,

numbers and special characters ( / ~ !@ $ ^ ( ) _ - { } [ ] ; , ) can be used.

FTP Port -

Deﬁne the FTP Server Port. If Port is not appropriate, it is impossible to access to FTP Server.

User ID -

Deﬁne User ID to access to the FTP Server. Fill out the correct User ID registered in the FTP Server.

Password -

Deﬁne Password to access to the FTP Server. Fill out the correct Password registered in the FTP

Server.

Click ‘Apply’ to save all settings.

Refer to the above image for example.

Setup - Network Setup

SMTP Settings

To send/save the image to the relevant sites by Email, SMTP needs to be setup.

General Setting -

Enable or disable the SMTP function.

Mode -

Select the security mode of SMTP from Plain or SSL / TLS. After checking the account setup of your

SMTP Server, you may select one.

SMTP Server Address -

Deﬁne the SMTP Server Address. If the IP Address form is incorrect, a message box will

be shown to try again.

Port -

Deﬁne the Port used in the Plain or SSL / TLS security mode in the above.

User ID -

Deﬁne the User ID to access the SMTP Server. Fill out the correct User ID registered in the SMTP Server.

Password -

Deﬁne the Password to access the SMTP Server. Fill out the correct Password registered in the

SMTP Server.

E-Mail Sender -

Deﬁne the e-mail address of the E-Mail Sender. It will be displayed as the sender when the

camera sends an E-mail.

E-Mail Receiver -

Deﬁne the e-mail address of E-Mail Receiver. It will be displayed as the Receiver when the

camera sends an E-mail.

Title -

Deﬁne the title of the E-Mail when the camera sends an E-mail.

The title of the Email is limited to 40 characters including the spaces.

Message -

Deﬁne the contents of E-Mail when the camera sends an E-mail. The message of the Email is limited

to 40 characters including the spaces.

Click ‘Apply’ to save all settings.

Setup - Network Setup

SNMP Settings

SNMPv1/SNMPv2 -

Select the SNMPv1/SNMPv2 option and type the names of Read and Write communities.

SNMP trap can be used to check periodically for operational thresholds or failures that are deﬁned in the MIB.

SNMP Trap -

Enable or disable the SNMP trap.

SNMPv3 contains cryptographic security, a higher security level, which allows you to set the Authentication password and the Encryption password.

Mode -

Select the either Read or Read/Write mode.

Activation -

Select mode to enable or disable.

Read/Write name -

Deﬁne Read name and Write name.

Security Level -

Select one of no auth, no priv/auth, priv

Authentication Algorithm -

Select MD5 or SHA as the authentication method.

Authentication Password -

The Authentication Password is encryption for authentication and is between 8

to 30 digits long.

Click ‘Apply’ to save all settings.

Setup - Network Setup

RTSP Information

Target Stream -

Select the stream you want to set.

Time out -

Set the RTSP time out.

The session is disconnected after the speciﬁed time out.

QoS Setting -

Set the quality of service to ensure data transfer performance.

RTP Multicast -

Check RTP Multicast Start/Stop. To activate RTP Multicast.

1. Click the “On” button.

2. Enter accessible RTP Multicast IP, the port for video stream control, RTP packet TTL.

3. Click the “Apply” button.

It is possible to set each RTP Multicast for CH1~3.

Click ‘Apply’ to save all settings.

Click this button when completed setup each channel.

It shows RTSP Connection information.

Setup - Trigger Action Setup

Action Rules Configuration

Action rules List -

It indicates the custom action rule information added to the Action rules list.

Click ‘Add’ to add custom action rules.

Click ‘Modify' to modify selected items from the action rules list.

Click 'Delete' to delete selected items from the action rules list.

Setup - Trigger Action Setup

Action Rules Add / Modify

Name -

Define the name of the action rules.

Input text cannot exceed the limit (3~15 characters).

Action1 ~ Action5 -

Select the action to take If the event occurs.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous menu.

Setup - Trigger Action Setup

Image Transfer Configuration

Pre / Post Alarm Image -

Image Transfer due to event is configured by setting Image transfer rate and Pre /

Post alarm duration.

Number of Images

Pre-alarm Duration

Post-alarm Duration

Click ‘Apply’ to save all settings.

Setup - Trigger Action Setup

Relay Out Configuration

Relay Output -

Select the Relay output.

The number of relay outputs available depends on the camera model.

Mode -

Select the monostable/bistable for relay mode.

Idle State -

Select whether the contact is normally opened or is closed.

Duration -

Relay out is operated during the setting time.

If monostable mode is selected, this function must be set up.

Click 'Apply' to save all changes.

Setup - Event Setup

Event Rules Configuration

Event Rules List -

It indicates the custom Event Rule information added to the Event Rules list.

Click ‘Add’ to add custom event rules.

Click ‘Modify' to modify selected items from the event rules list.

Click 'Delete' to delete selected items from the event rules list.

Setup - Event Setup

Event Rules Configuration

Name -

Define the Event rule name.

Event -

Select the event among motion detection, network disconnection, illegal login detected,

temperature critical, schedule,

sensor detection.

Click 'Cancel' to return to the previous setting.

You need at least one event.

Rules -

Select the action rule defined in the Trigger Action-Action rule menu.

Click ‘Save’ to save the current settings.

Click 'Cancel' to return to the previous setting.

Setup - Event Setup

Motion Detection Configuration

Motion Detection -

It shows the Motion event status.

Event Alert Icon( ) appears if ‘Motion Detection’ is activated.

Area -

Set the motion detected area. Click in the display window to draw the motion area.

You can set up to four areas.

Activation -

Enable or Disable motion detection function.

Sensitivity -

Deﬁne the sensitivity of motion detection.

If High value is selected, it will detect very small motion while it becomes relatively insensitive when Low value

is selected.

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous setting.

Setup - Event Setup

Temperature

Mode -

Select Fahrenheit or Celsius.

Threshold -

Deﬁne the temperature at which the event trigger occurs.

Temperature -

It indicates the current temperature of the IP camera.

Click ‘Apply’ to save all settings.

Setup - Event Setup

Alarm Configuration

Input Device Setup -

Select input device type from OFF / N.O. / N.C.

OFF

Operation

Ignore this input sensor.

The contact is normally open and closed when activated.

The contact is normally closed and open when activated.

Click ‘Apply’ to save all changes.

Setup - Record Setup

Record Management

Target Stream -

Select the channel you want to record video.

Click ‘Save’ to save the current settings.

Recording List -

Display the information about the recording settings.

Click ‘Modify’ to modify the selected item in the recording list.

Setup - Record Setup

Record Configuration

Enabled -

Enable or disable this function.

Storage Device -

This option shows the SD card currently mounted on the camera.

File Type -

Select the recording file type.

Currently, the camera supports MP4 file type.

Storage -

Select the storage type. SD Card (Disabled) selection is not allowed.

Continuous -

If continuous mode is enabled, the camera will start recording automatically.

Pre Duration -

Define the duration of recording before an event.

Post Duration -

Define the duration of image transfer after an event.

Click ‘Save’ to save the current settings.

Click 'Cancel' to return to the previous setting.

Setup - Record Setup

Recording List

Storage -

Select the Storage from the available options.

Filter -

Select the date/time, event, sort or storage format to filter the recorded video results.

Click the 'Refresh' button to refresh the search results as needed.

Click 'Filter' to view the ﬁltered recorded video.

Recording List -

Display the information of the recorded video.

Click 'Play' to view the selected item in the list of the recorded video results.

Click 'Download' to download the selected item.

- When you click Download, the following window appears.

- When downloading, please fill up the purpose of the file download. The field is limited to 30

characters. (This information will be shown on the Log page with the download time).

When playing back recorded MP4 files with H.265 (HEVC) codec, video may not play due to a

performance issue of VLC plug-in.

Setup - Record Setup

Recording Video

Recording Video Viewer -

Play the recorded video.

Recording Video Information -

Display information about the recorded video.

Click 'Replay' to view the recorded video again.

Click 'Back' to return to the previous menu.

Setup - Record Setup

Storage Configuration

Display the SD card information mounted on the device.

Select an item from the Storage List to configure its related functions.

Setup - Record Setup

Storage Configuration

Storage Size -

Total capacity of SD card and the remainder of it are displayed.

Auto Delete -

Select the period for auto delete. The data stored before the set period will be deleted

automatically.

Delete all stored images older than selected time.

Overwrite -

If ON is selected, once the SD card has less than 8MB storage available, new data will start to

overwrite the oldest data. If OFF is selected, once the SD card has less then 8MB available, the camera

will stop recording to the SD card.

Unmount -

Remove the SD card from the device.

Format -

Delete all contents stored in the SD card.

Click ‘Apply’ to save all settings.

Click 'Cancel' to return to the previous setting.

Setup - Security Setup

IP Address Filter Configuration

IP Address Filter -

Enable or disable this function.

IP Filter Type -

Select the recording IP filter type.

Click ‘Apply’ to save all settings.

Filter IP Address -

Display the filtered IP address.

IP Address -

Define the IP address you want to apply the IP filter.

Click ‘Add’ to add the IP address to the list.

Click ‘Remove’ to remove the IP address selected in the list.

Setup - Security Setup

RTSP Authentication Configuration

RTSP Authentication -

Enable or disable the RTSP authentication.

Click ‘Apply’ to save all settings.

Setup - Security Setup

IEEE 802.1X Configuration

The feature is needed when connecting the camera to the network protected by the IEEE 802.1X.

IEEE 802.1x -

Enable or disable the IEEE 802.1x feature.

Protocol

• MD5: It provides one-way password-based network authentication of the client.

• PEAP: It is similar to TTLS in that it does not require a certificate on the client-side.

• TTLS/MD5: It does not require a certificate on the client-side.

• TLS: It relies on client-side and server-side certificates to perform authentication.

EAPOL Version -

Select the EAPOL Version.

ID -

Type the ID to identify the client in the IEEE 802.1X authentication server.

Password -

Type the Password to identify the client in the IEEE 802.1X authentication server.

Verify -

Verify Password.

CA Certificate -

Select the CA certificate required for TLS, TTLS, and PEAP authentication.

Certificate -

Select the client certificate required for TLS authentication

Click ‘Apply’ to save all settings.

Setup - Security Setup

HTTPS Configuration

HTTPS encrypts session data over SSL or TLS protocols instead of using plain text in socket communications.

Certificate -

Select an installed certificate.

If you cannot select a certificate, please install the certificate from the Security->Certificates menu.

HTTPS connection Policy -

Select one of “HTTP”, “HTTPS”, “HTTP and HTTPS” depending on the connected web, ONVIF, RTSP over HTTP.

• WEB: “HTTP” “HTTPS” “HTTP and HTTPS”

• ONVIF, RTSP OVER HTTP: “HTTP” “HTTPS” “HTTP and HTTPS”

Click ‘Apply’ to save all settings.

When HTTPS mode is chosen, input https://<IP Address> to connect to the camera.

Setup - Security Setup

Certificates Configuration

8 9

Server/Client Certificates -

Shows the installed certificates.

Create Self-Signed Certificate -

A self-signed SSL certificate is an identity certificate signed by its creator.

But they are considered to be less trustworthy.

Properties -

Shows information about the selected certificate.

Delete -

Delete the selected certificate.

Create a Certificate signing request -

This is the encoded data that contains the necessary information for

issuing the certificate.

They must be ﬁlled in when creating the CSR (Certiﬁcate Signing Request).

Install Certificate -

Install Certification

CA Certificate -

Shows the installed CA certificates.

Install CA Certificate -

Install Certification, see the detail page.

Properties -

Shows information about the selected certificate.

Delete -

Delete the selected CA certificate.

Setup - Security Setup

Certificates Configuration

Detail for Install Certiﬁcation.

Certiﬁcate From Signing Request -

Select to install a signed certiﬁcate returned from the CA.

Certiﬁcate And Private Key -

Select to install Certiﬁcate And Private Key to install a certiﬁcate and private key.

Certiﬁcate Name -

Enter a unique name to identify a certiﬁcate.

Select File -

Choose the certiﬁcation ﬁle.

OK -

Request installing a certiﬁcate.

Cancel -

Cancel install certificate and then back to certificates configuration.

Detail for Install CA Certiﬁcation.

Certiﬁcate Name -

Enter a unique name to identify CA certiﬁcate.

Select File -

Choose a CA certiﬁcation ﬁle

OK -

Request installing a CA certiﬁcate.

Cancel -

Cancel installing a CA certificate and then back to certificates configuration.

Setup - Security Setup

Service Conﬁguration

SSH -

Enable or disable the SSH function.

Click ‘Apply’ to save all settings.

Setup - System Setup

System Information

System Capability information.

Device Name -

You can define the device name.

Location -

You can define the device's location.

Click ‘Apply’ to save all settings.

Setup - System Setup

System Diagnostics

Shows basic hardware functions after inspection.

Shows Uptime, SD card, NAND, EEPROM, Audio chip, Important file system, and NTP Status.

Warning:

If the camera is abnormally terminated, a download button will appear on the diagnostics page to download a

file that allows you to check the error information you can.

Setup - System Setup

Firmware Update

Version Information -

It shows the current Firmware Version in the system.

Web Update -

Select the Firmware ﬁle in your computer by clicking [Select ﬁle] button.

Start F / W Update -

Click this button to start the update. Progress of uploading will be displayed using

Progress Bar. If you assign the wrong ﬁle name, an error message will be shown.

Warning:

1. Do not turn oﬀ power to the camera while updating firmware as it may cause the system to become

instable. Once the update has completed, the system will automatically reboot.

2. Make sure to check the ‘Notice’ shown on screen.

If the ﬁrmware update is completed successfully, the camera will reboot and show the login window.

Setup - System Setup

Date & Time Settings

TimeZone Setup -

Choose the time zone for the camera. It will be activated after clicking the ‘Apply’ button.

Before setting below ‘New Camera Date and Time’, set the correct time zone ﬁrst.

Time Format -

Select the time format yy-mm-dd or mm/dd/yy.

Current Date and Time -

Shows the current date and time setting in the Camera.

Synchronize with my computer -

Set the date/time using those of PC currently connected.

Setup manually -

Set the date/time by typing manually.

Synchronize with time sever Time Zone (NTP) -

Choose time server available to connect to the current

camera. Date and Time will be updated automatically every hour when connected.

Click ‘Apply’ to save all settings.

Setup - System Setup

DST Settings

Daylight Saving Time (DST) is the practice of setting the clocks forward one hour from standard time during the summer months, and back again in the fall, to make better use of natural daylight.

General Setting -

Enable or disable the DST function.

Date and Time Settings -

Set the start time and end time that the DST applies.

Click ‘Apply’ to save all settings.

Setup - System Setup

Users Management

2 3 4

Users -

List all the user accounts for authentication.

Add -

Password

Retype Password

Password Hint

User

Authority

Enter a new user ID. Admin already exists.

Enter the user password. (Check the password)

Enter the user password again for veriﬁcation.

Enter the password hint.

Select Operator or Viewer.

Viewer: Only monitoring is allowed.

Operator: Most of the functions are allowed except ‘Setup’.

The ID and Password are limited to 8 characters with at least two combinations of uppercase letters,

lowercase letters, numbers and special characters.

Acceptable special characters are: ~ ' ! $ ^ ( ) _ - { } [ ] ; . ? /

Click ‘Save’ to save all settings.

Click 'Cancel' to return to the previous menu.

Modify -

Modify the information of the user accounts registered. For the admin account, only Password

function can be modiﬁed.

Delete -

Delete the selected user account. The admin account cannot be deleted.

Setup - System Setup

System Log

Filter -

Select a date, time, sort, or type of log to ﬁlter the log.

Click the 'Refresh' button to refresh the log list.

Click 'Filter' to view the ﬁltered log.

Click 'Backup' to back up the ﬁltered log.

System Log List -

The ﬁltered log is displayed.

Setup - System Setup

Factory Reset

Reset to the factory defaults -

Return the setup to the factory default.

All -

Reset all Settings to the factory defaults.

Except Network Settings and User Settings -

Reset all camera settings to factory default except for the network settings.

Click ‘Apply’ to save all settings.

Setup - System Setup

Restart

If you click the ‘RESTART’ menu, a message box will be shown to conﬁrm. Click the ‘OK’ button to restart.

Setup - System Setup

System Open Source License

This menu will show you all the list of System Open Source License in the camera.

Open Source Name / Version / License.

Network Setup -

Quick Start of Network Connection

Follow the steps below to complete the initial network setup.

Do not power on the IP camera until instructed.

Temporarily disable any proxy servers conﬁgured in

If connecting the IP camera directly to a modem, power down and reset the modem. Leave the modem powered down until the camera's conﬁguration is complete and the IP Camera has been connected to the modem.

Connect the IP camera to the conﬁgured network.

Open the DW IP Finder on a PC on the same

network as the camera and search for the camera.

If you have a DHCP server, it will automatically set the camera's IP address and network settings.

If you do not have a DHCP server, the camera's IP address is set by default to 192.168.1.80 after one minute In this case, the

PC's IP address must be changed to match the camera's IP address settings to be able to access the camera.

If multiple cameras are added at the same time,

each camera can be identified by its mac address.

Click on the camera's IP address and connect to

the web page.

Default ID/password are both: admin.

Familiarize yourself with the viewer interface.

Install VLC to display live video.

The camera's IP address settings can be set to

‘STATIC’ from the DW IP Finder or the camera's

web viewer by going to Setup -> Network ->

Network Settings.

If the IP camera is connected to a network with a

router, you must have port forwarding conﬁgured

on your router to access the camera from outside

the network.

After conﬁguring port forwarding on your router

(if necessary), access your IP camera by opening

Internet Explorer and typing the IP address and

web port assigned to the IP camera.

Example: http://192.168.0.200:8888

If your web port is 80, you do not need to specify the port in the address bar to access to your IP camera.

Access your IP Camera via the Internet (from a different network from the one your camera is):

If you use a static IP address assigned by your ISP:

1. Open Internet Explorer.

2. Type the address of the IP camera.

3. If you use a router, enter the routers’ static IP

and the web port number of the IP camera.

If you have a dynamic address provided by your ISP

1. Open Internet Explorer and go to your DDNS

website.

2. Register the IP camera.

3. Reboot the IP camera.

4. Give the DDNS server 10 minutes to locate your

IP camera’s IP information.

5. Click the refresh button in Internet Explorer.

6. After your camera is connected, select your

camera.

Network Setup -

DDNS Registration

If you have a DYNAMIC IP service from your

Internet Service Provider (ISP), you can’t tell the current IP address of the IP Camera.

To solve this problem, you have to register with our DDNS service.

At ﬁrst, you have to check if you are using dynamic addressing. If so, register your IP

Video Server on our DDNS website before you conﬁgure, setup, or install the IP Camera.

Even if you are not using DHCP, it mya be beneficial to register a DDNS. Instead of using a public IP adress (ex: http://201.23.4.76:8078), the DDNS will be more tsimplified (hostname.

dyndns.com/gate1).

For more details, contact our Support Center.

To use a public DDNS called ‘DynDNS’ or ‘no-IP’,

refer to the detailed information on how to use the

service. (Visit: http://www.dyndns.com

or http://www.no-ip.com)

Network Setup -

Guide to the Network Environment

Please conﬁgure the IP Camera at the installation site. You must determine your network scenario to conﬁgure the IP Camera with the proper TCP/IP settings.

This tutorial will guide you through the process. Before actually conﬁguring the IP

Camera, determine settings to be applied.

Record those settings to be used to conﬁgure your IP Camera for reference.

When conﬁguring your IP Camera, treat the

IP Camera as another PC on your network.

You will assign it to several addresses and other TCP/IP properties to match your current network.

This step-by-step tutorial will teach what IP addresses and network conﬁgurations should be assigned based on the network scenario.

Before you begin, locate any information and

settings received from your Internet Service

Provider (ISP). You may need to refer to these IP

addresses at a later time during the conﬁguration.

Current TCP/IP Settings

IP Address

Subnet Mask

Default Gateway

Primary DNS Server

Secondary DNS Server (Option)

Static Dynamic

If you were not given any IP addresses or the ISP was responsible for the setup and installation of your

Internet connection, go to step 2.

If you are not using a router on your network, your ‘Current TCP/IP Settings’ (from the previous section) and ‘Assigned IP Addresses from My ISP’ will be exactly the same.

You must determine whether the IP address is

STATIC or DYNAMIC. Contact your ISP to get a

STATIC IP address for the camera.

Conﬁgure your IP Camera’s TCP/IP settings for

network connectivity by selecting Setup from the

main interface and selecting TCP/IP located on the

left of the setup screen.

If prompted for ID and password, use ‘admin’ for

both entries. The default web port number is 80.

If port 80 is blocked by the ISP, use a value

between 1025 ~ 60000. If TCP port 80 is blocked,

contact your ISP.

The following descriptions are several basic

network scenarios. Determine which scenario

describes your network. If your network does not

match one of the scenarios below and you are

unsure how to setup your IP camera, contact your

network administrator.

You cannot control the rectangular gray areas and only

the ISP has access to the devices.

Network Setup -

Setup Case A, B

Case A:

Dynamic IP + Personal Router [Most SOHO]

Internet

Camera

Personal Router

W/Integrated

Switch

Phone Line or CATV

Cable/xDSL Modem

(ISP Provided)

Case B:

Static(Fixed) IP + Personal Router [Eﬃcient]

Internet

Camera

Public Line

Personal Router

W/Integrated

Switch

Gateway or Router at ISP

Conﬁgure your IP Camera’s TCP/IP properties:

Network Type: STATIC (even though you have

Dynamic IP from your ISP, use STATIC on the IP

camera).

Internet Address: A private IP address such as

192.168.0.200 (example)

You need to assign an IP address to the IP Camera just

as you do with PC.

The IP address you assign must be unique to your network and match your network as well.

For information on how to choose a unique IP and match your network, read the FAQ.

The IP address you assign must be a private IP.

For information on how to choose a private IP please, read the FAQ.

Subnet Mask: 255.255.255.0 (example)

You must use the same subnet mask as the one you noted under ‘Current TCP/IP Settings’.

Default Gateway: 192.168.0.1 (example)

This IP address must be the IP address of your router.

(private or LAN side)

Use the same Default Gateway you noted under

‘Current TCP/IP Settings’.

Preferred DNS Server: Use the 1st DNS Server from

‘Assigned IP Address from My ISP’.

If you did not receive any IP addresses from your ISP, contact the ISP and acquire the IP address of their

DDNS Server: Use the DDNS server.

This is the same site you will register later to accommodate dynamic IP from your ISP.

Web Port: 8888

Do not use the default port 80 as this number must be

changed.

Select a number between 1025 ~ 60000.

Network Setup -

Setup Case C, D

Case C:

Static(Fixed) IP

[Dedicated line directly to the IP Camera]

Case D:

Dynamic IP + DSL/Cable Modem

[Connected directly to the IP Camera]

Camera Camera

Internet

Phone Line or CATV

Cable/xDSL

Modem (ISP

Provided)

Gateway or Router at ISP

Public Line

Internet

To connect the IP Camera directly to a modem, power down and reset the modem. Leave the modem

powered down until the IP camera's setup is completed

and the IP camera has been connected to the modem.

Then power on the modem, followed by the IP camera.

Conﬁgure your IP Camera’s TCP/IP properties:

Network Type: STATIC

Internet Address: A static IP address received from your ISP such as 24.107.88.125 (example)

You need to assign an IP address to the IP Camera just as you do with PC.

Subnet Mask: Subnet mask assigned from your ISP such as 255.255.255.240 (example)

Default Gateway: 24.107.88.113 (example)

Use the assigned default gateway from your ISP.

Preferred DNS Server: Use the 1st DNS Server from

‘Assigned IP Address from My ISP’

If you have not received any IP addresses from your

ISP, contact them to acquire the IP address of their

DDNS Server: Use the DDNS server

This is the same site you will register later to utilize our DDNS service.

Web Port: 80

Select a number between 1025 ~ 60000.

Conﬁgure your IP Camera’s TCP/IP properties:

Network Type: DYNAMIC

DDNS Server: Use the DDNS server

This is the same site you will register later to accommodate dynamic IP from your ISP.

Web Port: 80

Select a number between 1025 ~ 60000.

Network Setup -

Port Forwarding

After entering the correct TCP/IP settings, you are ready for ‘Port Forwarding’

(Cases A, B).

Use the table below to note your camera's

TCP/IP settings for future reference. You may need

this information to access your IP Camera and to

conﬁgure ‘port forwarding’.

IP camera TCP/IP settings

IP address

Subnet mask

Default gateway

Preferred DNS server

DDNS server

Web port

After clicking ‘Apply’, the system will prompt for a

reboot. Please allow the system 50 seconds to

reboot and accept the changes. After 50 seconds,

close the conﬁguration screen. The view will

display ‘Trying to Reconnect’.

If the ACTIVE light on the IP Camera has gone oﬀ

and is now back on again ﬂashing, the IP Camera

has rebooted. After the system reboots

completely, remove the power supply from the

unit and close Internet Explorer.

Return your PC/Laptop TCP/IP properties to their

original settings.

Before installing the IP camera, you must perform

port forwarding on your router (Cases A, B).

You will need to forward 1 port:

· Web Port: All the ports will be forwarded to the

IP address you assigned to the IP Camera.

In the example above, you would forward:

· 8888 > 192.168.0.200

Network Setup -

Starting IP Camera

After forwarding correctly the Web Port, through your router (if applicable), install the

IP Camera in a proper location.

Locate the serial number located on the label attached to the bottom of the IP camera, you will need this for DDNS registration.

Connect the IP Camera to your router or cable/

DSL modem (per your network scenario) via a

Cat5/5e UTP Ethernet network cable.

Supply power to the IP camera.

After 1 minute, verify the IP camera indicators:

· LINK: Flickering/Solid

After conﬁguring port forwarding on your computer (if necessary), access your IP camera on your local network by opening Internet

Explorer and specifying the IP address and web port assigned to the IP camera.

Examples: http://192.168.0.200:8888 or

http://24.106.88.123

If you left your web port as 80, you do not need to specify the port in the address bar to access the IP camera.

Access your IP camera via the Internet :

If you use cases B, C:

1. Open Internet Explorer.

2. Type the address of the IP camera.

3. If you use a router, enter the routers’ static IP

and the web port number of the IP camera.

If you use cases A, D:

1. Open Internet Explorer and go to your DDNS

website.

2. Register the IP camera.

3. Reboot the IP camera.

4. Give the DDNS server 10 minutes to locate your

IP camera’s IP information.

5. Click the refresh button in Internet Explorer.

6. After your camera is connected, select your

camera.

The diﬀerence between B and C is that B needs to set the port forwarding.

Since the type of DDNS diﬀers from the service type, refer to the related service site.

Appendix

FAQ

1. My POWER light is not on?

Power is not being supplied to the unit. Please use the power supply shipped with the unit and verify that a power source is active from the attached power outlet used to connect the adapter. You can test this by plugging in any other electrical device and verify its operation. After using the power supply shipped with the product, check the power source, and reinserting the power connector into the IP Camera, please call our Support Center.

The power supply may be defective.

2. My ACTIVE light is not ﬂashing?

Verify the power supply to the unit. Power oﬀ the unit and back on again, wait 1 minute, if the ACTIVE light still does not begin to ﬂash, you will have to set the unit to its factory default (THIS WILL DELETE ANY CONFIGURATION

AND SET THE UNIT TO THE FACTORY DEFAULTS).

Power on the unit and insert the end of a paper clip into the small recessed opening on the back of the unit. Use the clip to press the button located within that opening.

3. My LINK light is not ﬂashing or solid?

Verify the cable connection. 99% of the time the cable’s connection to the unit is causing this problem. Try using a diﬀerent network cable or crossover cable (for PC connection only). Try reinserting the cable, if this still doesn’t solve the problem call our Support Center.

4. I can access the video server on my LAN, but not from the

Internet.

Verify that your router (if applicable) has port forwarding properly conﬁgured. If accessing from our DDNS service, verify the correct serial number. Firewall issues may prevent user access.

5. How do I open an MS-DOS or Command Prompt?

Start > (All) Programs > Accessories > Command Prompt

6. How do I ﬁnd out my IP address information if my settings were automatically detected?

1) Open a Command Prompt

2) At the prompt type - “ipconﬁg / all” (without the quotes)

3) Near the end of the information supplied, should be

your current IP address, subnet mask, default gateway and DNS servers

7. I can’t connect!!

In the case of a connection failure.

Modem Reboot > Modem Reboot Finished > Router

Reboot > Router Reboot Finished > IP Camera Reboot

> IP Camera Reboot Finish > Verify DDNS and IP Camera connection, if applicable.

8. How do I “PING” an IP address?

1) Open an MS-DOS (or Command) prompt

2) At the prompt type - “ping xxx.xxx.xxx.xxx” (without the

quotes and replace the “x” s with an IP address)

3) Press Enter

9. I’m accessing my video server remotely over the Internet and the video stream is choppy, is this normal?

Yes. The frames per second received remotely are determined by your bandwidth capabilities both at your site where the IP Camera is installed and your remote location. The lower of the two sites will determine how fast your video stream is received. It is recommended to have at least a 256Kb/sec upstream connection from the site where the IP Camera is installed. Lower speeds will operate properly but provide poor remote performance.

The Faster the Internet connection at both ends, the faster the video stream.

10. How do I enable or check VLC on my browser

Internet Explorer

Open Internet Explorer > Tools on the menu bar > Internet

Options > Security Tab > Custom Level > Scroll down and verify that you are prompted or have enabled plug-ins to be downloaded and executed. > click OK > restart browser.

Chrome

Open Chrome > Chrome menu settings > Advanced settings > Individual information - content settings > Run

automatically

11. How do I reset the unit to factory defaults?

Refer to the previous functions page and ﬁnd the reset button. Power ON the unit and use a paper clip to push the reset button within that opening. You should then see the ACTIVE light turn oﬀ and after a few seconds, the

ACTIVE light will begin to ﬂash, signifying a successful reboot. If the ACTIVE light does not turn oﬀ after depressing the reset button, please try holding the button in for a few seconds and releasing it. YOU WILL LOSE ALL

DATA THAT HAD BEEN ENTERED PREVIOUSLY AND THE IP

CAMERA WILL BE SET TO ITS FACTORY RESETS.

Specifications -

Dimensions

Unit: inches (mm)

1.88" (48mm)

4.9" (125mm)

Specification -

Spec.

CAMERA

Image Sensor

Total Pixels

Focal Length

Horizontal Angle

Shutter Speed

MIN. Illumination

Day and Night

BLC

DNR

Privacy Zone

AGC

Other Image

Processing

1/1.7” 12.4M CMOS

4000 (H) X 3000 (V)

2.1mm, F2.2

D: 185°, H: 185°, V: 185°

Auto / Manual (1/15 ~ 1/32000),

Anti-Flicker, Slow Shutter (off,

2X, 3X, 5X, 6X, 7.5X, 10X)

0.3 Lux, 0 Lux with IR (F2.2)

H3IR, 80ft

TDN (True Day and Night)

On / Off

3D-DNR

16 Programmable Zones

Auto

Configurable Exposure, White

Balance, Sharpness, BLC

ENCODER (VIDEO AND AUDIO)

Video

Compression

H.265, H.264, MJPEG

H.264 Profile MP / HP

H.265 Profile MP

Multiple Profile

Streaming

Performance

Video Bitrate

3008 x 3000p30 +

320 x 320p30 with

H.265, H.264 + MJPEG

100kbps ~ 10Mbps, Multi-rate for

Preview and Recording

Bitrate Control

Edge Storage

Multi Streaming CBR/VBR at

H.265, H.264 (Controllable frame rate and Bandwidth)

Micro SD, Micro SDHC, Micro

SDXC (not included)

I/O AND EVENT

Audio In/Out

Alarm In/Out

1 [1.0Vrms, 3k

1 / 1

Ω ] / 1

Event Notification FTP, E-mail, Alarm out, SD card

SECURITY AND NETWORK

Network Protocol

Security

IPv4:

TCP/IP / UDP / AutoIP /

RTP(UDP/TCP) / RTSP / NTP /

HTTP / HTTPS / SSL / DNS /

DDNS / DHCP / FTP / SMTP /

ICMP / SNMPv1/v2/v3(MIB-2) /

ONVIF

HTTPS (SSL), IP filtering, 802.1x,

Digest Authentication (ID/PW)

Plug in CGI API, ONVIF

GENERAL

Power

Temperature

Material

Dimensions(DXH)

Weight

Certification

POE IEEE 802.3af Class3

(Adaptor is not Included)

DC12V: Max 8.5W

PoE: Max 10W

-4°F ~ 122°F (-20°C ~ 50°C)

Aluminum vandal fisheye housing, polycarbonate dome

4.9" x 1.88”

(125 x 48mm)

1.1 lbs (0.5 kg)

FCC, CE, ROHS, IP66, IK9

Warranty Information

Digital Watchdog (referred to as “the Warrantor”) warrants the Camera against defects in materials or workmanship as follows:

Labor: For the initial five (5) years from the date of the original purchase if the camera is determined to be defective, the Warrantor will repair or replace the unit with the new or refurbished product at its option, at no charge.

Parts: Also, the Warrantor will supply replacement parts for the initial two (2) years.

To obtain warranty or out of warranty service, please contact a technical support representative at

1+ (866) 446-3595, Monday through Friday from 9:00 AM to 8:00 PM EST.

A purchase receipt or other proof of the date of the original purchase is required before warranty service is rendered. This warranty only covers failures due to defects in materials and workmanship which arise during normal use. This warranty does not cover damages which occurs in shipment or failures which are caused by products not supplied by the Warrantor or failures which result from accident, misuse, abuse, neglect, mishandling, misapplication, alteration, modification, faulty installation, setup adjustments, improper antenna, inadequate signal pickup, maladjustments of consumer controls, improper operation, power line surge, improper voltage supply, lightning damage, rental use of the product or service by anyone other than an authorized repair facility or damage that is attributable to acts of God.

Limits

and

Exclusions

There are no express warranties except as listed above. The Warrantor will not be liable for incidental or consequential damages (including without limitation, damage to recording media) resulting from the use of these products, or arising out of any breach of the warranty. All express and implied warranties, including the warranties of merchantability and fitness for a particular purpose, are limited to the applicable warranty period set forth above.

Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other rights from vary from state to state.

If the problem is not handled to your satisfaction, then write to the following address:

Digital Watchdog, Inc.

ATTN: RMA Department

16220 Bloomfield Ave

Cerritos, CA 90703

Service calls which do not involve defective materials or workmanship as determined by the Warrantor, in its sole discretion, are not covered. Cost of such service calls are the responsibility of the purchaser.

DW® East Coast office and warehouse: 5436 W Crenshaw St, Tampa, FL USA 33634

DW® West Coast office and warehouse: 16220 Bloomfield Ave, Cerritos, CA USA 90703

PH: 866-446-3595 | FAX: 813-888-9262 www.Digital-Watchdog.com [email protected]

Technical Support PH:

USA & Canada 1+ 866-446-3595

International 1+ 813-888-9555

French Canadian:

+ 1-904-999-1309

Technical Support hours: Monday-Friday 9 a.m. to 8 p.m. Eastern Time

Hello! I am an AI chatbot specifically trained to assist you with the Digital Watchdog DWC-PVF9Di2TW MEGApix® Pano™ 9MP vandal fisheye IP camera User's Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Assistant typing

Assistant terminated

MEGApix ®

andal

IP

amera

User’s Manual

Safety Information

CAUTION

CAUTION :

Important Safety Instructions

Table of Contents

Introduction

Product and Accessories

Part Names

Disassembling the Camera

Before installing your camera, you have to read the following cautions.

Basic Installation

Installation Using Mounting Plate

Installation Using Mounting Bolts and Nuts

Cabling

Cabling

Managing the SD Card

Network setup -

DW IP Finder

Basic Screen (Default)

Basic Screen

Video Configuration

Video Configuration

Video Configuration

Video Configuration

OSD Configuration

Region of Interest Configuration

Audio Configuration

Privacy Mask Configuration

Camera Image Adjustment

Camera Exposure Settings

Camera Day & Night Settings

Camera Backlight Settings

Camera White Balance

Camera Image Enhancement

Video Enhancement

Network Status

Network Settings

Auto IP Settings

ONVIF Settings

UPNP Settings

DDNS Settings

FTP Settings

SMTP Settings

SNMP Settings

RTSP Information

Action Rules Configuration

Action Rules Add / Modify

Image Transfer Configuration

Relay Out Configuration

Event Rules Configuration

Event Rules Configuration

Motion Detection Configuration

Temperature

Alarm Configuration

Record Management

Record Configuration

Recording List

Recording Video

Storage Configuration

Storage Configuration

IP Address Filter Configuration

RTSP Authentication Configuration

IEEE 802.1X Configuration

HTTPS Configuration

Certificates Configuration

Certificates Configuration

Service Conﬁguration

System Information

System Diagnostics

Firmware Update

Date & Time Settings

DST Settings

Users Management

System Log

Factory Reset