Ohlins 35020-08 Porsche 987, Cancellation kit PASM, Mounting Instruction
Add to my manuals6 Pages
Ohlins 35020-08 is a cancellation kit compatible with Porsche 987 vehicles. It is designed to work with Öhlins products and allows for the deactivation of the standard damper control system. The kit includes various components such as cable ties, holder plates, connectors, pin contacts, heat shrink, screws, and nuts. It is recommended to have an Öhlins dealer install the cancellation kit for safety reasons.
advertisement
Kit Contents
Description
Cables ties 4,8x290
Cable ties 3,5x190
Holder plate front
Holder plate rear
Connector
Pin contact
Heat shrink
Screw M4x8
Screw M4x5
Nut M6
Screw M6
Cancellation kit (350 mm)
Cancellation kit (1000 mm)
Part No
Note!
Please note that this image is a general representation of the product and may differ slightly from your product.
Pcs
1
2
4
6
4
1
3
1
2
8
8
8
4
Cancellation kit PASM, Porsche 987
35020-08
Mounting Instructions
MOUNTING INSTRUCTIONS
⚠
arning!
It is advisable to have an Öhlins dealer install the cancellation kit.
⚠
arning!
If working on a raised vehicle, ensure it is securely supported.
Preparation:
1)
1
Cut off 150 mm / 5,9 inch of the standard damper control cable.
2
Remove 15 mm / 0,6 inch of the cable insulation and 4-5 mm / 0,16 - 0,2 inch of the wire insulation. Attach the heat shrink tube.
2)
3
Install the supplied pin contact with a correct tool.
0,5 mm²
150 mm / 5,9 inch
4
Insert the completted wire into the connector until to the lock. After this lock the connector and move the heat shrink tube to the middles of the connector / the wire and heat it. The pinposition / cable colour is not relevant.
2/6
MOUNTING INSTRUCTIONS
Front axle:
M4x8
5
Install the cancellation kits with the supplied M4 screws on the holder plate.
6
Install the cancellation kit and the holder with the supplied screws and a stopp nut in the vehicle. The assembly position is beside the battery.
✋
Caution!
The cancellation kit gets very hot! All attached lines within a distance of 2 cm / 0,8 inch have to be removed further away from the kit.
350 mm 1000 mm
3/6
MOUNTING INSTRUCTIONS
Front axle:
7
Run the standard damper control wire with adapter to the cancellation kit connector.
Insert the standard connector into the cancellation kit connector until it locks.
Fix the wire with cable ties.
Right vehicle side
Left vehicle side
4/6
MOUNTING INSTRUCTIONS
Rear axle:
8
Install the cancellation kit and the holder on the standard screws of the rear lights. The assembly position is under the convertible top.
✋
Caution!
The cancellation kit gets very hot! All attached lines within a distance of 2 cm / 0,8 inch have to be removed further away from the kit.
Left vehicle side
Right vehicle side
5/6
9
Run the standard damper control wire with adapter to the supplied cancellation kit connector. Insert the standard connector into the supplied cancellation kit until it locks and reassembly the cover.
✋
Caution!
The cancellation kit gets very hot! All attached lines within a distance of 2 cm / 0,8 inch have to be removed further away from the kit.
Öhlins products are subject to continuous improvement and development, therefore, although these instructions include the most up-to-date information available at the time of printing, minor updates may occur.
To find the latest information contact an Öhlins distributor.
Please contact Öhlins if you have any questions regarding the contents in this document.
© Öhlins Racing AB. All rights reserved. Any reprinting or unauthorized use without the written permission of Öhlins Racing AB is prohibited.
Öhlins Racing AB
Box 722
S-194 27 Upplands Väsby, Sweden
Phone +46 8 590 025 00 fax +46 8 590 025 80
Part no. MI_35020-08_0
Issued 2016-05-16
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project