AG Neovo TX-10 User manual

AG Neovo TX-10 User manual
TX-10 LCD Monitor
www.agneovo.com
User Manual
TABLE OF CONTENTS
SAFETY INFORMATION
WEEE............................................................................................................................................................ 4
PRECAUTIONS
Notice............................................................................................................................................................ 5
Cautions When Setting Up............................................................................................................................ 5
Cautions When Using.................................................................................................................................... 6
Cleaning and Maintenance............................................................................................................................ 7
Notice for the LCD Display............................................................................................................................ 7
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents................................................................................................................................... 8
1.2 Removal and Fitting Cable Cover........................................................................................................... 9
1.3 Installing an Open Frame Monitor with L-Brackets............................................................................... 10
1.4 Wall Mounting........................................................................................................................................ 11
1.5 LCD Display Overview.......................................................................................................................... 12
1.6 Wired OSD Controller............................................................................................................................ 13
CHAPTER 2: MAKING CONNECTIONS
2.1 Connecting the AC Power..................................................................................................................... 14
2.2 Connecting Input Source Signals.......................................................................................................... 15
2.3 Connecting Audio Devices.................................................................................................................... 16
2.4 Connecting the Wired OSD Controller.................................................................................................. 16
2.5 Connecting USB for Touch Screen Control........................................................................................... 17
2.6 Ventilation Requirements for Enclosure Locating.................................................................................. 17
CHAPTER 3: USING THE LCD DISPLAY
3.1 Turning on the Power............................................................................................................................ 18
3.2 Displaying the OSD Menu..................................................................................................................... 18
3.3 Adjusting Display Brightness................................................................................................................. 19
3.4 Adjusting Display Contrast.................................................................................................................... 19
3.5 Using Auto Adjustment Function........................................................................................................... 20
CHAPTER 4: ON SCREEN DISPLAY MENU
4.1 Using the OSD Menu............................................................................................................................ 21
4.2 OSD Menu Tree.................................................................................................................................... 22
CHAPTER 5: ADJUSTING THE LCD DISPLAY
5.1 Brightness Menu................................................................................................................................... 23
5.2 VGA Setting Menu................................................................................................................................. 24
5.3 System Menu........................................................................................................................................ 25
5.4 Language Menu.................................................................................................................................... 26
5.5 Colour Temperature Menu..................................................................................................................... 26
CHAPTER 6: APPENDIX
6.1 Warning Messages................................................................................................................................ 27
6.2 Timing.................................................................................................................................................... 27
6.3 Cleaning................................................................................................................................................ 28
6.4 Troubleshooting..................................................................................................................................... 29
6.5 Transporting the LCD Display............................................................................................................... 30
2
TABLE OF CONTENTS
CHAPTER 7: SPECIFICATIONS
7.1 Display Specifications........................................................................................................................... 31
7.2 Display Dimensions............................................................................................................................... 32
3
Safety Information
SAFETY INFORMATION
WEEE
Information for users applicable in European Union countries
The symbol on the product or its packaging signifies that this product has to be disposed
separately from ordinary household wastes at its end of life. Please kindly be aware that
this is your responsibility to dispose electronic equipment at recycling centers so as to help
conserve natural resources. Each country in the European Union should have its collection
centers for electrical and electronic equipment recycling. For information about your recycling
drop off area, please contact your local related electrical and electronic equipment waste
management authority or the retailer where you bought the product.
4
Precautions
PRECAUTIONS
PRECAUTIONS
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Symbols used in this manual
This icon indicates the existence of a potential hazard that could result in personal injury
or damage to the product.
This icon indicates important operating and servicing information.
Notice
• Read this User Manual carefully before using the LCD display and keep it for future reference.
• The product specifications and other information provided in this User Manual are for reference only. All
information is subject to change without notice. Updated content can be downloaded from our web site at
www.agneovo.com.
• To protect your rights as a consumer, do not remove any stickers from the LCD display. Doing so may
affect the determination of the warranty period.
Cautions When Setting Up
Do not place the LCD display near heat sources, such as a heater, exhaust vent, or in direct
sunlight.
Do not cover or block the ventilation holes in the housing.
Place the LCD display on a stable area. Do not place the LCD display where it may subject to
vibration or shock.
Place the LCD display in a well-ventilated area.
Do not place the LCD display outdoors.
Do not place the LCD display in a dusty or humid environment.
Do not spill liquid or insert sharp objects into the LCD display through the ventilation holes.
Doing so may cause accidental fire, electric shock or damage the LCD display.
5
PRECAUTIONS
Cautions When Using
Use only the power cord supplied with the LCD display.
The power outlet should be installed near the LCD display and be easily accessible.
If an extension cord is used with the LCD display, ensure that the total current consumption
plugged into the power outlet does not exceed the ampere rating.
Do not allow anything to rest on the power cord. Do not place the LCD display where the power
cord may be stepped on.
If the LCD display will not be used for an indefinite period of time, unplug the power cord from
the power outlet.
To disconnect the power cord, grasp and pull by the plug head. Do not tug on the cord; doing
so may cause fire or electric shock.
Do not unplug or touch the power cord with wet hands.
WARNING:
Unplug the power cord from the power outlet and refer to qualified service personnel under
the following conditions:
• When the power cord is damaged.
• If the LCD display has been dropped or the housing has been damaged.
• If the LCD display emits smoke or a distinct odor.
Ceiling mount or mount on any other horizontal surface overhead are not advisable.
WARNING:
Installation in contravention of the instructions may result in undesirable consequences,
particularly hurting people and damaging property. Users who have already mounted the
display on the ceiling or any other horizontal surface overhead are strongly advised to contact
AG Neovo for consultations and solutions to help ensure a most pleasurable and fulfilling
display experience.
6
PRECAUTIONS
Cleaning and Maintenance
Do not attempt to service the LCD display yourself, refer to qualified service personnel.
Opening or removing the covers may expose you to dangerous voltage or other risks.
Notice for the LCD Display
In order to maintain the stable luminous performance, it is recommended to use low brightness setting.
Due to the lifespan of the lamp, it is normal that the brightness quality of the LCD display may decrease
with time.
When static images are displayed for long periods of time, the image may cause an imprint on the LCD
display. This is called image retention or burn-in.
To prevent image retention, do any of the following:
• Set the LCD display to turn off after a few minutes of being idle.
• Use a screen saver that has moving graphics or a blank white image.
• Switch desktop backgrounds regularly.
• Adjust the LCD display to low brightness settings.
• Turn off the LCD display when the system is not in use.
Things to do when the LCD display shows image retention:
• Turn off the LCD display for extended periods of time. It can be several hours or several days.
• Use a screen saver and run it for extended periods of time.
• Use a black and white image and run it for extended periods of time.
There are millions of micro transistors inside the LCD display. It is normal for a few transistors to be
damaged and to produce spots. This is acceptable and is not considered a failure.
7
Chapter 1: Product Description
CHAPTER 1: PRODUCT DESCRIPTION
1.1 Package Contents
When unpacking, check if the following items are included in the package. If any of them is missing or
damaged, contact your dealer.
LCD Display
Quick Start Guide
Warranty Card
Quick Start Guide
TX-10 LCD Monitor
TX-10_Quick Guide_V010
displays.agneovo.com
Power Adapter(*)
Power Cord
VGA Cable
DisplayPort Cable
USB Cable
(Touch Function)
Side Bracket Package
Screw Package
Wired OSD Controller
MENU
SELECT
M4 x 8pcs
Note:
• Use only the supplied power cord.
• The above pictures are for reference only. Actual items may vary upon shipment.
• (*) Must use only the supplied power adapter:
- Vendor: DELTA ELECTRONICS, INC.
- Model no.: ADP-36PH BBE
- Rating: DC 12V, 3A
8
PRODUCT DESCRIPTION
1.2 Removal and Fitting Cable Cover
1. Remove the screw securing the cable cover. Then remove the cable cover from the monitor.
Cable Cover
2. Connect the cables and route them through the slots on the cable cover.
3. Install the cable cover and secure it using a screw.
9
PRODUCT DESCRIPTION
4. Secure the cables to the cable cover using the cable ties.
Cable Tie
1.3 Installing an Open Frame Monitor with L-Brackets
To install an open frame monitor with L-brackets, you need the following items:
Bracket 1 X 2pcs
Bracket 2 X 2pcs
Screw M4 X 8pcs
1. Install the two Bracket 1 to the rear of the monitor. Then secure the brackets using the four
screws.
Bracket 1
2. Install the two Bracket 2 to the customer’s cabinet. Then secure the brackets using the four
screws.
Bracket 2
10
PRODUCT DESCRIPTION
3. Align the screw holes of the Bracket 1 with the screw holes of the Bracket 2. Then
assemble the L-bracket by securing the brackets using the screws.
1.4 Wall Mounting
To wall-mount the LCD display, screw the mounting bracket to the VESA holes at the rear of the LCD display.
100mm
100mm
Note: Take measures to prevent the LCD display from falling down and lessen possible injury and damage
to the display in case of earthquakes or other disasters.
• Use only the 100 x 100 mm wall mount kit recommended by AG Neovo. All
AG Neovo wall mount kits comply with VESA standard.
• Secure the LCD display on a solid wall strong enough to bear its weight.
• It is suggested to wall mount the LCD display without tilting it facing
downward.
11
PRODUCT DESCRIPTION
1.5 LCD Display Overview
Rear
Front
Audio-Out
1
1
DC IN
2
DP
3
HDMI
VGA
USB
RJ45
4
5
6
7
Audio OUT:
Connect audio signals output (3.5 mm Stereo Audio Jack). Only applicable for DisplayPort or
HDMI input signal.
2
DC IN:
Connect with the supplied power adaptor.
3
DisplayPort IN:
Connect DisplayPort signals input.
4
HDMI IN:
Connect HDMI signals input.
5
VGA IN:
Connect VGA signals input.
6
USB Type-B Port (Touch):
Connect USB for touch screen control.
7
Wired OSD Controller Port (RJ45):
Connect the wired OSD controller.
12
PRODUCT DESCRIPTION
1.6 Wired OSD Controller
MENU
1
2
3
SELECT
4
5
1
MENU:
• Press to display OSD menu.
• When OSD menu is ON, press to hide OSD menu or return to the previous menu.
2
UP (p):
• Press to display the Brightness quick menu. Press the p/q button to adjust the brightness level.
• When OSD menu is ON, press to select a main item, select sub-item function, or adjust the
settings.
3
DOWN (q):
• Press to display the Contrast quick menu. Press the p/q button to adjust the contrast level.
• When OSD menu is ON, press to select a main item, select sub-item function, or adjust the
settings.
4
SELECT:
• For VGA input signal source, press to perform auto adjustment.
• When OSD menu is ON, press to confirm the selection or select sub-item function.
5
POWER (
):
Press to turn the power on or off.
13
Chapter 2: Making Connections
CHAPTER 2: MAKING CONNECTIONS
CAUTION:
Make sure that the LCD display is not connected to the power outlet before making any
connections. Connecting cables while the power is ON may cause possible electric shock or
personal injury.
2.1 Connecting the AC Power
1. Connect the power cord to the power adapter.
2. Connect the power adapter to the DC power input at the rear of the LCD display.
3. Connect the power cord plug to a power outlet or a power supply.
DC IN
CAUTION:
When unplugging the power cord, hold the power cord by the plug head. Never pull by the
cord.
14
MAKING CONNECTIONS
2.2 Connecting Input Source Signals
Input source signals can be connected with either of the following cables:
• DP
DP
HDMI
VGA
Connect one end of a DP cable to the DP connector of the
LCD display and the other end to the DP connector of the
computer.
• HDMI
Connect one end of an HDMI cable to the HDMI connector
of the LCD display and the other end to the HDMI
connector of the computer.
• VGA
Connect one end of a D-Sub (VGA) cable to the D-Sub
(VGA) connector of the LCD display and the other end to
DP
HDMI
VGA
the D-Sub (VGA) connector of the computer.
15
MAKING CONNECTIONS
2.3 Connecting Audio Devices
• Audio Output
Connect a headphone to the headphone jack of the LCD display.
Audio-Out
2.4 Connecting the Wired OSD Controller
Connect the wired OSD controller to the RJ45 connector of the LCD display.
MENU
RJ45
SELECT
16
MAKING CONNECTIONS
2.5 Connecting USB for Touch Screen Control
Connect one end of a USB cable to the USB connector of the LCD display and the other end to the USB
connector of the computer.
USB
USB
2.6 Ventilation Requirements for Enclosure Locating
To allow heat to disperse, avoid installing the LCD display directly on the cabinet wall and make sure the
operating/storage temperature/humidity requirements are met as described below:
•
•
•
•
Operating temperature: 0°C-50°C (32°F-122°F)
Non-operating temperature (independent of altitude): -20°C-60°C (-4°F-140°F)
Operating humidity (non-condensing): 20%-80%
Non-operating humidity (38.7°C (101.7°F) maximum wet bulb temperature): 10%-90%
17
Chapter 3: Using the LCD Display
CHAPTER 3: USING THE LCD DISPLAY
3.1 Turning on the Power
1. Connect the power to the LCD display. Refer to page 14.
2. Connect the wired OSD controller to the LCD display. Refer to page 16.
3. Press the
button on the wired OSD controller to turn the LCD display on.
MENU
SELECT
Power Button
When the LCD display is turned on, press the
button on the wired OSD controller to turn off the LCD
display.
Note: The LCD display still consumes power as long as the power cord is connected to the power outlet.
Disconnect the power cord to completely cut off power.
3.2 Displaying the OSD Menu
Press the MENU button to open the OSD menu. Press the MENU button again to close the OSD menu.
For more information on adjusting settings, refer to page 21.
MENU Button
MENU
SELECT
CONTRAST
BRIGHTNESS
FH :
1280 X
4 9 KHZ
The following menu appears on the screen:
CONTRAST
BRIGHTNESS
FH :
1280 X
4 9 KHZ
800
FV :
18
5 9 . 8 HZ
800
FV :
5 9 . 8 HZ
USING THE LCD DISPLAY
3.3 Adjusting Display Brightness
Press the p button to open the Brightness quick menu.
MENU
UP Button
SELECT
CONTRAST
BRIGHTNESS
100
The following menu appears on the screen:
CONTRAST
BRIGHTNESS
100
Then press the p/q buttons to adjust the LCD display brightness level.
3.4 Adjusting Display Contrast
Press the q button to open the Contrast quick menu.
MENU
DOWN Button
SELECT
CONTRAST
BRIGHTNESS
50
The following menu appears on the screen:
CONTRAST
BRIGHTNESS
50
Then press the p/q buttons to adjust the LCD display contrast level.
19
USING THE LCD DISPLAY
3.5 Using Auto Adjustment Function
Auto Adjustment function automatically tunes the LCD display to its optimal setting, including horizontal
position, vertical position, clock, and phase.
Press the SELECT button to perform auto adjustment if the source is VGA.
MENU
SELECT Button
SELECT
AUTO ADJUSTING
PLEASE WAIT
During the auto adjustment, the screen will slightly shake for a few sconds and you will see the following
message:
AUTO ADJUSTING
PLEASE WAIT
When the message disappears, auto adjustment is completed.
Note: It is recommended to use the auto adjustment function when using the LCD display for the first time
or after a resolution change.
20
Chapter 4: On Screen Display Menu
CHAPTER 4: ON SCREEN DISPLAY MENU
4.1 Using the OSD Menu
#
1
Menu Navigation
Operation
Display the main menu screen.
Press MENU.
CONTRAST
BRIGHTNESS
FH :
2
1280 X
4 9 KHZ
800
FV :
5 9 . 8 HZ
1 Press p/q to select the main menu item.
Enter the submenu.
2 Press SELECT to enter the submenu.
CONTRAST
BRIGHTNESS
3 Press SELECT (repeatedly if necessary) to
select the submenu item.
50
The active main menu or submenu icon is
highlighted
in orange.
CONTRAST
BRIGHTNESS
3
Press p/q to adjust the value or select the setting.
Adjust the settings or select the value.
For example:
50
4
Return to the main menu and/or close the OSD
Press MENU once to return to the main menu.
window.
Press MENU repeatedly (if necessary) to close the
OSD window.
Note: When settings are modified, all changes are saved when the user does the following:
• Proceeds to another menu
• Exits the OSD menu
• Waits for the OSD menu to disappear
21
ON SCREEN DISPLAY MENU
4.2 OSD Menu Tree
Main Menu
Brightness
Submenu
Reference
CONTRAST
Refer to page 23.
BRIGHTNESS
VGA Setting
AUTO ADJUST
Refer to page 24.
LEFT/RIGHT
DOWN/UP
HORIZONTAL SIZE
FINE
System
OSD LEFT/RIGHT
Refer to page 25.
OSD DOWN/UP
OSD TIMEOUT
FACTORY RESET
INPUT SELECT
Language
ENGLISH
Refer to page 26.
FRANÇAIS
DEUTSCH
ITALIANO
ESPAÑOL
日本語
繁中
簡中
Colour Temperature
9300
Refer to page 26.
6500
5500
7500
USER
Note: Availability of some menu items depend on the input source signal. If the menu is not available, it is
disabled and greyed out.
22
Chapter 5: Adjusting the LCD Display
CHAPTER 5: ADJUSTING THE LCD DISPLAY
5.1 Brightness Menu
1. Press MENU on the wired OSD controller to call out the OSD window.
2. Press p/q to select
and then press SELECT to enter the chosen menu.
3. Press SELECT (repeatedly if necessary) to select the submenu item.
CONTRAST
BRIGHTNESS
FH :
Item
CONTRAST
1280 X
4 9 KHZ
5 9 . 8 HZ
Function
Operation
Range
Adjusts the difference between the black
Press p/q to adjust the
level and the white level.
value.
Original Setting
BRIGHTNESS
800
FV :
High Setting
0 to 100
Low Setting
Adjusts the luminance of the screen image. Press p/q to adjust the
0 to 100
value.
Original Setting
High Setting
23
Low Setting
ADJUSTING THE LCD DISPLAY
5.2 VGA Setting Menu
1. Press MENU on the wired OSD controller to call out the OSD window.
2. Press p/q to select
and then press SELECT to enter the chosen menu.
3. Press SELECT (repeatedly if necessary) to select the submenu item.
AUTO ADJUST
LEFT/RIGHT
DOWN/UP
HORIZONTAL SIZE
FINE
FH :
Item
1280 X
4 9 KHZ
800
FV :
5 9 . 8 HZ
Function
Operation
Range
Configures auto adjustment settings.
Press p/q to activate
Note: During the auto adjustment, the
screen will slightly shake for a few
seconds.
auto adjustment.
LEFT/RIGHT
Moves the screen image to the left or right.
Press p/q to adjust the
0 to 100
DOWN/UP
Moves the screen image up or down.
value.
0 to 100
HORIZONTAL
Adjusts the screen image horizontal dot
SIZE
clock.
FINE
Adjusts the screen image pixel phase.
AUTO ADJUST
24
N/A
0 to 100
0 to 100
ADJUSTING THE LCD DISPLAY
5.3 System Menu
1. Press MENU on the wired OSD controller to call out the OSD window.
2. Press p/q to select
and then press SELECT to enter the chosen menu.
3. Press SELECT (repeatedly if necessary) to select the submenu item.
OSD LEFT/RIGHT
OSD DOWN/UP
OSD TIMEOUT
FACTORY RESET
INPUT SELECT
FH :
Item
1280 X
4 9 KHZ
800
FV :
5 9 . 8 HZ
Function
Operation
Range
OSD LEFT/
Moves the OSD window horizontal position
Press p/q to adjust the
0 to 100
RIGHT
to the left or right.
value.
OSD DOWN/UP
Moves the OSD window vertical position to
0 to 100
up or down.
OSD TIMEOUT
Sets the length of time (in seconds) the
5 to 60
OSD window is displayed. When the
time elapses, the OSD window closes
automatically.
FACTORY
Resets all settings to the factory defaults.
N/A
Displays
current input source and
OSDthe
LEFT/RIGHT
N/A
RESET
INPUT SELECT
OSD DOWN/UP
enables
toTIMEOUT
select manually
OSD
FACTORY RESET
INPUT SELECT
a new source.
VGA
INPUT SELECT
After activating the function, input options
1
will be displayed on the screen.
Press SELECT to
VGA
select the input
HDMI
source.
INPUT SELECT
2
VGA
HDMI
Press p/q to switch
to the selected
DISPLAY PORT
source.
ACTIVE
Note: If the selected source cannot be
found, the LCD display selects the
available source automatically.
25
DISPLAY PORT
ADJUSTING THE LCD DISPLAY
5.4 Language Menu
1. Press MENU on the wired OSD controller to call out the OSD window.
2. Press p/q to select
and then press SELECT to enter the chosen menu.
ENGLISH
FRANÇAIS
DEUTSCH
ITALIANO
FH :
ESPAÑOL
㘶㝽嫯
互Ṿ
䯑Ṿ
1280 X
4 9 KHZ
800
FV :
5 9 . 8 HZ
3. Press SELECT (repeatedly if necessary) to select your preferred language.
4. Press p/q to set the preferred language.
5.5 Colour Temperature Menu
1. Press MENU on the wired OSD controller to call out the OSD window.
2. Press p/q to select
and then press SELECT to enter the chosen menu.
9300
6500
5500
7500
USER
FH :
94
93
100
RED
GREEN
BLUE
1280 X
4 9 KHZ
800
FV :
5 9 . 8 HZ
3. Press SELECT (repeatedly if necessary) to select your preferred colour temperature from
9300, 6500, 5500, 7500, USER*.
4. Press p/q to set the preferred colour temperature.
Note: *If you set the colour temperature to USER, press p/q to adjust RED, GREEN, and BLUE
colour values manually.
26
Chapter 6: Appendix
CHAPTER 6: APPENDIX
6.1 Warning Messages
When any of these warning messages appear, check the following items.
Warning Message
Cause
The LCD display cannot detect the
NO SIGNAL INPUT
input source signal.
Solution
√√ Check if the input source is
turned ON.
√√ Check if the signal cable is
properly connected.
√√ Check if any pin inside the
cable connector is twisted or
broken.
The resolution or the refresh rate of
OUT OF RANGE
√√ Change the resolution or the
the graphics card of the computer
refresh rate of the graphics
is set too high.
card.
Note: If you see the “OUT OF
RANGE” message on the
screen, then the OSD menu
cannot be operated.
6.2 Timing
Timing Mode
IBM VGA
VESA
VESA
VESA
Resolution
Horizontal
Vertical
640
480
800
600
1024
768
1280
800
27
Refresh Rate
60
60
60
60
CHAPTER 6: APPENDIX
6.3 Cleaning
Front Panel Cleaning Instructions
• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth or a
soft, lint-free cloth.
• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to
remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same type
to dry.
• Do not use volatile substances such as insert sprays, solvents and thinners.
Cabinet Cleaning Instructions
• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.
• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to remove
as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the surface is dry.
• Do not allow any water or detergent to come into contact with the surface of the display. If water or
moisture gets inside the unit, operating problems, electrical and shock hazards may result.
• Do not scratch or hit the cabinet with fingers or hard objects of any kind.
• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.
• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.
28
APPENDIX
6.4 Troubleshooting
Problems
No picture.
Possible Cause and Solution
• Check if the LCD display is turned ON.
• Check if the power adapter is properly connected to the LCD display.
• Check if the power cord is plugged into the power outlet and to the
power adapter.
• Check if the LCD display is properly connected to the input source.
• Check if the input source is turned ON.
• Check if the input source is in standby mode, move the mouse or press
any button to wake it up.
Note: Do not connect the USB cable to the LCD display in order to
charge your laptop. Doing so will disable the LCD display to
wake up from sleep mode by simply touching the screen.
Image position is incorrect.
• For VGA input, adjust the “LEFT/RIGHT” and “DOWN/UP” settings in
VGA Setting menu (refer to page 24).
The displayed texts are
blurry.
Red, blue, green, white
dots appear on the screen.
• For VGA input, press SELECT on the wired OSD controller to adjust the
screen image. Refer to page 20.
• There are millions of micro transistors inside the LCD display. It is
normal for a few transistors to be damaged and to produce spots. This
is acceptable and is not considered a failure.
Faint shadows from a
static image appear on the
screen.
Dew formed on the LCD
display.
• Turn off the LCD display for extended periods of time.
• Use a screen saver or a black and white image and run it for extended
periods of time.
• This normally happens when the LCD display is moved from a cold
room to a hot room temperature. Do not turn ON the LCD display, wait
for the dew condensation to disappear.
29
APPENDIX
6.5 Transporting the LCD Display
To transport the LCD display for repair or shipment, place the display in its original packaging box.
1. Place the two foam cushions on each side of the LCD display for protection.
2. Place the LCD display down in the box.
3. Place the bag with accessories on the designated area (if necessary).
4. Close and tape the box.
ries
sso
e
c
Ac
Note:
• It is recommended to use the original packaging box.
• When repacking, carefully place the LCD display in its box and protect the glass panel from touching
any object.
30
Chapter 7: Specifications
CHAPTER 7: SPECIFICATIONS
7.1 Display Specifications
TX-10
Panel
Frequency (H/V)
Input
External Control
Audio
Touch Screen
Power
Glass
Operating Conditions
Storage Conditions
Mounting
Dimensions
Weight
Panel Type
Panel Size
Max. Resolution
Pixel Pitch
Brightness
Contrast Ratio
Viewing Angle (H/V)
Display Colour
Response Time
H Freq.
V Freq.
DisplayPort
HDMI
VGA
RJ45
Audio Out
Technology
Positional Accuracy
Panel Interface
Multi-touch Plug & Play
Single Touch Support by Driver
Multi-touch Support by Driver
Power Supply
Power Requirements
On Mode
Stand-by Mode
Off Mode
Thickness
Reflection Rate
Transmission Rate
Hardness
Temperature
Humidity
Temperature
Humidity
VESA FPMPMI
w/o Base (W x H x D)
Packaging (W x H x D)
w/o Base
Packaging
LED-Backlit TFT LCD (VA Technology)
10.1”
1280 x 800
0.169 mm
500 cd/m2
1300:1
170°/170°
16.2M
5 ms
31 kHz-50 kHz
56 Hz-60 Hz
x1
1.3a x 1
15-Pin D-Sub x 1
x 1 (Wired OSD Controller Port)
Stereo Audio Jack (3.5 mm)
Projective Capacitive
± 2.5 mm
USB (Type-B)
10-point touch for Windows 7/8/10
Windows VISTA/XP/2000/CE/XP Embedded, Mac OS
Linux (Up to 5 points)
Android 2.1 upward and 4.0 as well (Up to 10 points)
External
DC 12V, 1.0A
7W (On)
< 0.5W
< 0.5W
3.3 mm (0.13”)
< 12%
> 85%
> 7H
0°C-50°C (32°F-122°F)
20%-80% (non-condensing)
-20°C-60°C (-4°F-144°F)
10%-90% (non-condensing)
Yes (100 x 100 mm)
260.7 x 183.4 x 39.4 mm (10.3” x 7.2” x 1.6”)
370.0 x 325.0 x 160.0 mm (14.6” x 12.8” x 6.3”)
1.4 kg (3.1 lb)
2.4 kg (5.3 lb)
Note: All specifications are subject to change without prior notice.
31
SPECIFICATIONS
7.2 Display Dimensions
256.8
220
2
78.35
100
78.35
M4x6L
2
10
2.
2
5°
30.7
44.7
100
132.5
34.7
2
39.4
20.2
16.4
10.4
231.7
136.6(opening dimension)
183.4(outline dimension)
178.5(glass outline dimension)
260.7(outline dimension)
255.8(glass outline dimension)
218(opening dimension)
Cable cover
20.35
10
2.
5°
20.35
220.0
5°
2.
10
AG Neovo
Company Address: 5F-1, No. 3-1, Park Street, Nangang District, Taipei, 11503, Taiwan.
TX1000_UM_V012
Copyright © 2020 AG Neovo. All rights reserved.
32
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement