- Vehicles & accessories
- Motor vehicle accessories & components
- Car seat
- Chicco
- 00079771060070
- User Guide
Chicco Fit2® Car Seat User guide
Add to my manuals
46 Pages
Chicco Fit2® Car Seat: A rear-facing infant car seat designed for babies 4-35 lbs and up to 35 inches tall. It features a newborn positioner for infants 4-11 lbs, a 5-point harness for secure fastening, and a bubble level indicator for proper installation. The Fit2® is compatible with all Chicco Fit2 strollers, allowing for a seamless transition from car to stroller.
advertisement
Car Seat
User Guide
For future use, STORE USER GUIDE
in location on bottom of base.
®
IS0144E_08
©2020 Artsana USA, Inc. 03/20 www.chiccousa.com
If you have any problems with your Chicco Child Restraint, or any questions regarding installation or use, please call:
Chicco Customer Service
1-877-424-4226
Please have Model and Serial Number available when you call.
These are located on a label on the bottom of the Child Restraint.
For future reference, fill in the information below. The information can be found on the label on the bottom of the Child Restraint.
Model Number:
Serial Number:
Manufactured In:
TABLE OF CONTENTS
Registration
Child
Safe
Warnings 8
Best Practices
Need Help?
14
15
VEHICLE INFORMATION
Vehicle Seating Positions
Vehicle Seat Belts
What is LATCH?
16
18
20
CHILD RESTRAINT OVERVIEW
Child Restraint Components
Base Stage 1 & 2
22
26
BASE INSTALLATION
Install with Base Setup 30
Install Using LATCH 32
Install Using LAP-SHOULDER BELT 38
Install Using LAP BELT ONLY
Install Carrier to Base
44
48
WITHOUT BASE INSTALLATION
Install without Base Setup 52
Install Using LAP-SHOULDER BELT 54
Install Using Shoulder Belt Guide
Install Using LAP BELT ONLY
58
62
SECURING YOUR CHILD
Securing Child with Harness
Secure Child Checklist
66
74
ADDITIONAL INFORMATION
Base Release Handle
LATCH Storage
Newborn Positioner
Head Rest Insert
Handle Positions
Adjusting Crotch Strap
Canopy
Installation on an Aircraft
Cleaning and Maintenance
76
77
78
80
81
82
84
85
86
2
REGISTRATION
Please complete the Registration Card that came with your Child Restraint and mail it promptly.
Child Restraints could be recalled for safety reasons. You must register this restraint to be reached in a recall. Send your name, address, e-mail address if available, and the restraint’s model number and manufacturing date to:
Artsana USA, Inc.
1826 William Penn Way
Lancaster, PA 17601
or call 1-877-424-4226 or register online at http://www.chiccousa.com/carseatregistration.aspx
For recall information, call the U.S. Government’s Vehicle Safety Hotline at
1-888-327-4236 (TTY: 1-800-424-9153), or go to http://www.NHTSA.gov.
REGISTRATION
PAGE INTENTIONALLY LEFT BLANK
3
4
CHILD GUIDELINES
ONLY
use this Child Restraint if the child meets
BOTH
of the following
Weight and Height requirements:
• Weight is between 4 and 35 pounds (1.8 and 15.9 kg).
• Height is 35 inches (89 cm) or less and child's head is no less than
1" (25 mm) below the top of the head rest.
Base Stage 2 is ONLY for children who are able to crawl or walk.
The Newborn Positioner is only for infants who weigh between 4 and 11 pounds (1.8 and 5 kg). See Newborn Positioner on page 78.
For premature infants, you must consult the infant's doctor before using this Child Restraint. A premature infant may have difficulty breathing or have other medical problems when placed in a seated position.
CHILD GUIDELINES
WARNING!
Use of this Child Restraint is ONLY for children who meet ALL of the requirements shown here. If the child is not within these requirements, select a different car seat (such as a convertible car seat).
1 2
BASE STAGE 1
NEWBORN POSITIONER
4 lbs. 11 lbs. 15 lbs.
BASE STAGE 2
35 lbs.
(1.8 kg) (5 kg) (6.8 kg) (15.9 kg)
NEVER turn this Child Restraint FORWARD-FACING.
Discontinue the use of this Child Restraint as soon as the child reaches either the maximum weight OR maximum height.
1 2
5
6
SAFE USE CHECKLIST
YOUR CHILD’S SAFETY DEPENDS ON YOU!
You MUST follow the detailed instructions in this User Guide to ensure the steps below are performed correctly!
Make sure your child meets the weight and height requirements:
Refer to the “Child Guidelines” section on page 4.
If using Base, select the correct Base Stage for your child's developmental milestones, age, weight and height:
Refer to the “Base Stage 1” requirements section on page 26.
Refer to the “Base Stage 2” requirements section on page 28.
Select a safe seating location in your car:
Refer to the “Vehicle Seating Positions” section on page 16 and 17.
Install Base or Carrier Rear-Facing ONLY:
Refer to the “Child Guidelines” section on page 4.
SAFE USE CHECKLIST
Ensure that the Child Restraint is properly leveled when installed:
Check Child Restraint for a snug fit in your car:
While holding Child Restraint near belt path used, pull side to side and forward.
Belt should remain tight and Child Restraint should not move more than
1” (25 mm) from vehicle seat back or side-to-side.
Secure your child:
Refer to the “Securing Child with Harness” section on page 66.
7
8
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
FAILURE TO FOLLOW THESE INSTRUCTIONS AND THE PRODUCT
LABELS CAN RESULT IN SERIOUS INJURY OR DEATH TO YOUR CHILD.
Take Time to Read This User Guide
• Carefully read and understand all instructions and warnings in this User Guide. Your child’s safety depends on you knowing how to setup, install and use this Child Restraint properly.
• Before installing this Child Restraint in a vehicle, be sure to also check the vehicle owner’s manual for information on proper installation.
• NEVER
allow others to use this Child Restraint until they have read and understood all instructions in this
User Guide.
Make Sure Child Fits This Child Restraint
• Use only with children who weigh between 4 and 35 lbs (1.8 kg to 15.9 kg) and whose height is 35 inches
(89 cm) or less.
• Do Not
use this child restraint if top of child's head is within 1 inch (25 mm) of the top of the headrest.
• Only use the NEWBORN POSITIONER provided for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Secure Child Properly
• Snugly adjust the belts provided with this child restraint around your child. A loose harness could cause the child to be ejected in a sharp turn, sudden stop or crash, resulting in serious injury or death.
A snug strap should not allow any slack. It lies in a relatively straight line without sagging.
It does not press on the child’s flesh or push the child’s body into an unnatural position.
• NEVER
use clothing or blankets that interfere with fastening or tightening the harness. An unsecured child could be ejected in a sharp turn, sudden stop or crash!
To keep child warm, place a blanket over child and restraint AFTER you have properly secured child in harness.
• ALWAYS
check to make sure buckle is securely latched. If buckle separates, child could be killed or seriously injured.
• NEVER
leave child unattended. Do not allow children to play in or around the Child Restraint.
• ALWAYS
keep child properly secured in harness whenever child is in carrier.
9
10
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
• NEVER PLACE THIS CHILD RESTRAINT IN VEHICLE SEATING LOCATION
WITH A FRONTAL AIR BAG, UNLESS THE AIR BAG CAN BE TURNED OFF.
If the airbag inflates, it can cause serious injury or death to your child. For vehicles with side air bags, refer to your vehicle owners manual for information on your child restraint installation.
• ALWAYS
install this Child Restraint in a back seat if possible.
According to accident statistics, children are safer when properly restrained in the rear seating positions rather than in the front seat.
• NEVER
install in a rear facing, side facing or on the back of a folded down vehicle seat.
• ALWAYS
secure this Child Restraint with the vehicle’s child restraint anchorage system (LATCH) if available
OR with a vehicle seat belt.
• ALWAYS
install rear-facing when using this Child Restraint in a vehicle. Your child could be killed or seriously injured if you install this restraint forward-facing.
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Install Child Restraint Correctly
• BEFORE
each use,
ALWAYS
check to make sure restraint is tightly secured in the vehicle seat.
• NEVER
use Child Restraint in a vehicle seating position where it cannot be secured tightly. A loosely installed child restraint will not protect your child in a crash.
• Never leave carrier or base unsecured in your vehicle even when it is unoccupied.
It could injure other occupants in a sharp turn, sudden stop or crash.
• DO NOT
install this child restraint using an inflatable seat belt. The interaction of the inflatable portion of the vehicle’s belt with this child restraint
can result in serious injury or death
. Install using LATCH instead, or move the car seat to a position with a suitable seat belt type.
• To
prevent ejection or breathing difficulties, proper recline is required.
When installing the Child
Restraint, check the bubble level on the base. Refer to pages 26-28 to make sure your child meets the requirements for Stage 1 or Stage 2.
• Make sure nothing interferes with carrier attachment to base. ALWAYS check attachment.
• ONLY
use Chicco Fit 2 infant carriers with Fit 2 bases.
• DO NOT
use Chicco KeyFit/KeyFit 30/KeyFit 35 infant carriers with the Chicco Fit 2 base.
11
12
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Ensure Child’s Safety When Using Child Restraint
• NEVER leave child unattended.
• SUFFOCATION HAZARD:
Infant carrier can roll over on soft surfaces and suffocate child. NEVER place carrier on beds, sofas or other soft surfaces.
• STRANGULATION HAZARD:
Children have
STRANGLED
in loose or partially buckled harness straps.
Fully restrain the child even when carrier is used outside the vehicle.
• Fall Hazard:
Child's activity can move carrier.
NEVER
place carrier on counter tops, tables, or any other elevated surface.
• Fall Hazard:
The carrier can fall from the shopping cart. Do not use on shopping cart.
• Do not use the infant carrier if it is damaged or broken.
• BE SURE
handle is locked in the “carry position” before lifting carrier by handle. An unlocked handle could move unexpectedly, causing injury to child.
• ALWAYS
check buckle and other parts for hot surfaces. A hot surface could burn child! Cover unoccupied carrier with blanket when leaving in a vehicle exposed to sunlight or high temperatures.
IMPORTANT WARNINGS
WARNING
DEATH or SERIOUS INJURY CAN OCCUR
Check Condition of Restraint
• DO NOT
use if the Harness or LATCH straps are cut, frayed or damaged.
• DO NOT use this Child Restraint if it is more than 6 years old.
Check manufacturer’s label on underside of Child Restraint for the “Do Not Use After” date.
• DO NOT use any accessories, pads or products not included with this Child Restraint, unless approved by Chicco USA.
Doing so will void the warranty of this Child Restraint.
• You MUST replace this Child Restraint if it has been involved in a crash, even if you cannot see visible damage.
A damaged Child Restraint may not protect your child in a future crash.
• Do not modify your Child Restraint.
• For proper removal and installation of the harness straps contact Chicco USA for additional instructions.
• Do not use Child Restraint if any component is damaged, broken, or missing parts.
Call 1-877-424-4226 to find out if the damaged part or parts can be replaced.
13
14
BEST PRACTICES
• Ensure all vehicle occupants are properly restrained before traveling. Unrestrained occupants can be thrown around and may be seriously injured or seriously injure other occupants in a sharp turn, sudden stop or crash.
• Do not leave loose objects, such as books, bags, etc., in the back of the vehicle. In the event of a sharp turn, sudden stop, or crash, loose objects can be thrown around and possibly cause serious injury to vehicle occupants.
• Cover the Child Restraint when the vehicle is parked in sunlight. Parts of a Child Restraint can become very hot if left in the sun. Contact with these parts can burn a child’s skin.
Always check the surface of any metal or plastic parts before putting your child in the
Child Restraint.
• To avoid strangulation, Do not allow children to play with vehicle seat belts. If possible, move unused belts out of reach.
• Do not use anything to raise the Child Restraint off the vehicle seat. In a sharp turn, sudden stop, or crash, the Child Restraint could slide and potentially cause serious injury.
• Never use a second-hand Child Restraint with an unknown history.
• Never use any accessories that are not included with this child restraint, unless specifically approved by Chicco. For more information, go to www.chiccousa.com/accessories.
• The Head Rest Insert can be used with or without the Newborn Positioner.
NEED HELP?
Need Help Securing Your Child Restraint?
The following sources are available to help ensure your Child Restraint is properly installed:
• Contact Chicco USA by visiting our website at www.chiccousa.com or calling our Customer Service 1-877-424-4226. Please have Model and
Serial Number available when you call. These are located on a label on the
• Refer to your vehicle manual for Child Restraint installation tips.
• Contact a certified Child Passenger Safety Technician in your area by visiting safercar.gov and select “Find Local Child Seat Help” or call
1-866-SEAT CHECK (1-866-732-8243).
15
VEHICLE SEATING POSITIONS
16
WARNING! NEVER PLACE THIS CHILD RESTRAINT IN A
VEHICLE SEATING LOCATION WITH A FRONTAL AIR BAG,
UNLESS THE AIR BAG CAN BE TURNED OFF.
The back seat is the safest place for children 12 and under. See your vehicle owner’s manual for Child Restraint installation and instructions.
VEHICLE SEATING POSITIONS
Some vehicles have no seating positions which are compatible with this Child
Restraint. If in doubt, contact the vehicle manufacturer for assistance. Only forward-facing vehicle seats can be used with this Child Restraint.
Make sure no more than 4 inches (10 cm) of the Child Restraint base is past the edge of the vehicle seat.
Do not use on a folded down vehicle seat back.
17
18
VEHICLE SEAT BELTS
The information in this section only applies to installation with vehicle seat belts.
For simplest installation use LATCH
Vehicle seat belts differ from vehicle to vehicle. Refer to your vehicle owner’s manual for specific information about seat belts and their use with Child
Restraints.
Shoulder belt with switchable retractor:
Putting the shoulder belt in the locked/switched mode as the last step is optional. The shoulder belt Lock-Off replaces the need for the locked/switched mode. Using the locked/switched mode may cause Child Restraint to tilt.
VEHICLE SEAT BELTS
The following types of vehicle belts MUST NOT be used to install this Child Restraint.
If any of the belt types listed below are in the chosen seating position, choose another vehicle seating position or use LATCH if available.
1
2 3
4 5
1.
Motorized (automatic) vehicle belts.
4.
Non-Locking (ELR) Lap Belts.
2.
Door mounted vehicle belts.
5.
Inflatable seat belts.
3.
Lap-shoulder Belts with 2 retractors (unless Lap Belt has a “Lock Mode”).
19
20
WHAT IS LATCH
WARNING:
This Child Restraint is designed to be used with lower LATCH anchors at the standard spacing (11 inches (28 cm)) ONLY! Refer to vehicle owner’s manual for information about LATCH and Child Restraint installation positions.
LATCH
=
L
ower
A
nchors and
T
ethers for
CH
ildren
United States Motor Vehicle Safety Standards have defined a system for installing
Child Restraints in vehicles called LATCH.
LATCH may ONLY be used IN PLACE
OF vehicle belt if the vehicle is equipped with LATCH anchor points. DO NOT use both the seat belt and LATCH at the same time. Please refer to the vehicle owner’s manual for designated LATCH locations in vehicles.
LATCH
in the vehicle consists of a top tether anchor point, which is not used with this child restraint, and two lower anchor points. Some vehicles owner’s manual use the term “
ISOFIX
”.
LATCH
can also be used in vehicle seating positions equipped with
ISOFIX
.
If the vehicle is equipped with
LATCH
, the vehicle lower anchor points may be visible at the seat crease. If not visible, the seating position may be marked with a symbol (fig. a) or a colored dot.
(fig. a)
Vehicle
Lower Anchor
Points
WHAT IS LATCH
Vehicle
Seat Crease
21
22
CARRIER COMPONENTS
Head Rest
Insert
Head Rest
Harness
Straps
Shoulder
Pads
Newborn
Positioner
Harness
Adjuster Strap
Head Rest
Adjustment Tab
Canopy
Canopy
Mount
Chest Clip
Buckle
Harness
Adjuster Button
Shoulder
Belt Guide
(when installing carrier without the base)
Head Rest
Cross Bar
Harness
Strap
Harness
Splitter Plate
Crotch Strap
Retainer
CARRIER COMPONENTS
Base Release
Handle
Carry
Handle
Handle
Release
Button
Seat Belt Guide
(when installing carrier without the base)
23
BASE AND LATCH COMPONENTS
Base Stage
Lever
Leveling Foot
Adjuster
LATCH
Pull Strap
24
User Guide
Storage
(Inside Base)
Bubble
Level
Indicator
Base Stage
Indicator
1 2
LATCH
Connector
LATCH
Release
Lever
Carrier
Attachment
Hook
Shoulder Belt
Lock-Off
Recline
Foot
BASE AND LATCH COMPONENTS
PAGE INTENTIONALLY LEFT BLANK
25
26
BASE STAGE 1
Choose the Stage that best fits your child:
Stage 1 allows for a more reclined install and riding position for a child that meets the weight and height requirement for this restraint.
BASE STAGE 1
BASE STAGE:
4 – 35 lbs (1.8 – 15.9 kg)
1
NEWBORN POSITIONER
4 lbs. 11 lbs. 35 lbs.
(1.8 kg) (5 kg) (15.9 kg)
Use with children:
• Who weigh between 4 and 35 lbs
(1.8 –15.9 kg).
• And height is less than 35 inches (89 cm).
• And top of head is at least 1 inch (25 mm) below top of Head Rest.
• When Harness Straps can be positioned
at or just below the child’s shoulders * .
*
See Harness Height Adjustment on page 68.
BASE STAGE 1
To install this Child Restraint in Stage 1, rotate the Base Stage Lever over into Stage 1 on the Base. The Base Stage Indicator '1' icon will turn orange.
1 2
1 2
Install Child Restraint:
• Base installation continued on page 30
1 2
27
28
BASE STAGE 2
Choose the Stage that best fits your child:
Stage 2 is an upright install for a child that meets the developmental requirement for this restraint. This allows for more leg room and a more upright riding position for your child.
2
BASE STAGE 2
BASE STAGE:
15 – 35 lbs (6.8 – 15.9 kg)
15 lbs. 35 lbs.
(6.8 kg) (15.9 kg)
Use with children:
• Who are able to
crawl or walk
(approximately 9 months old)
.
• Who weigh between 15 and 35 lbs (6.8 –15.9 kg).
• And height is less than 35 inches (89 cm).
• And top of head is at least 1 inch (25 mm) below top of
Head Rest.
• When Harness Straps can be positioned at
or just below the child’s shoulders * .
See Harness Height Adjustment on page 68.
*
BASE STAGE 2
Infants may have difficulties breathing in a more upright seating position. ONLY use base Stage 2 with children that can crawl or walk. Approximately 9 months old.
To install this Child Restraint in Stage 2, rotate the Base Stage Lever over into
Stage 2 on the Base. The Base Stage Indicator '2' icon will turn orange
.
2
1 2
1 2
Install Child Restraint:
• Base installation continued on page 30
1 2
29
30
1
2
INSTALL WITH BASE SETUP
Infants may have difficulty breathing when in a sitting position. Make sure the seat is reclined properly so that your child’s head does not fall forward.
Failure to properly recline the Child Restraint could increase the child’s risk of serious injury or death.
LEVEL
See page 16 for "Vehicle Seating Positions" before installing. Make sure the vehicle is on a level surface. Place Base on selected vehicle seat. Make sure it is not blocking the vehicle seat belt buckle.
Set Base Stage Lever to the correct Stage, depending on your child. See pages
26-29 for more information
(2a)
. Locate the Bubble Level Indicator and adjust the seat recline by pulling up on the center Leveling Foot Adjuster until the Bubble falls between the arrows on the Bubble Level Indicator
(2b)
.
Installation Options:
• LATCH
installation continued on page 32
• Lap-Shoulder Belt installation continued on page 38
• Lap Belt Only installation continued on page 44
2b
INSTALL WITH BASE SETUP
31
32
1
2
INSTALL USING LATCH
Store LATCH Connectors properly in the compartments when not using for installation - See page 77.
When installing with LATCH in vehicle equipped with inflatable seat belts, the unused seat belt should not be buckled behind the
Child Restraint System as this will engage the inflatable portion of the belt.
Pull up on the LATCH Release Lever and loosen LATCH straps to their full length.
Locate the LATCH Connector storage compartments. Remove both LATCH
Connectors.
1 2
INSTALL USING LATCH
33
34
3
4
INSTALL USING LATCH
Locate the LATCH anchor bars in your vehicle. Attach both LATCH
Connectors to the vehicle LATCH anchor bars.
Tighten LATCH straps by pulling up on LATCH Pull Strap while pressing Base firmly into vehicle seat.
3
INSTALL USING LATCH
4
35
36
5
INSTALL USING LATCH
Roll LATCH Release Strap and store in Release Strap Storage Compartment.
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
Install Child Restraint:
• I nstallation continued on page 48
5
INSTALL USING LATCH
CHECK YOUR WORK
37
38
1
2
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite side of the Base. Buckle the vehicle seat belt.
1
INSTALL USING LAP-SHOULDER BELT
2
Belt
Path
CLICK!
39
40
3
INSTALL USING LAP-SHOULDER BELT
While pushing down on the Base, pull up on the vehicle shoulder belt to remove all slack from the vehicle lap belt.
3
INSTALL USING LAP-SHOULDER BELT
41
42
4
INSTALL USING LAP-SHOULDER BELT
While holding the shoulder belt tight, slide the shoulder belt strap firmly into Shoulder Belt Lock-Off. Always use the Lock-Off on the opposite side of where the vehicle seat belt is buckled.
Do
NOT
pull on shoulder belt after it is positioned in Lock-Off.
This could damage the Lock-Off and/or the vehicle belt
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
Install Child Restraint:
• I nstallation continued on page 48
4
INSTALL USING LAP-SHOULDER BELT
CHECK YOUR WORK
43
44
1
2
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up through the belt path on the side of the Base.
Pull vehicle seat belt down through the vehicle seat belt path on opposite side of the Base. Buckle the vehicle seat belt.
1
INSTALL USING LAP BELT ONLY
2
Belt
Path
CLICK!
45
46
3
INSTALL USING LAP BELT ONLY
While pushing down on the Base, pull up on the loose end of the vehicle lap belt to remove all slack.
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Base should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Check installation before every use!
Install Child Restraint:
• I nstallation continued on page 48
3
INSTALL USING LAP BELT ONLY
CHECK YOUR WORK
47
48
INSTALL CARRIER TO BASE
IMPORTANT:
Before installing Child Restraint refer to page 26-29 to determine the best Base Stage for your child.
1
2
Insert the Carrier into the Base.
Push down on the Carrier to make sure it locks onto the Carrier
Attachment Hooks on the Base.
1
INSTALL CARRIER TO BASE
2
49
50
3
INSTALL CARRIER TO BASE
Check to make sure the Carrier is securely attached to the Base.
ALWAYS lift up on Carrier to verify it is properly attached to the Base.
CHECK YOUR WORK
Hold Base at each side and pull side to side and forward. Child Restraint should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Make sure Child Restraint is level by confirming that the bubble on the level indicator is between the level lines. Make sure infant’s head does not fall forward. If necessary, re-adjust recline and repeat installation steps to make sure Child Restraint is installed properly.
Check installation before every use!
3
INSTALL CARRIER TO BASE
51
52
1
2
3
INSTALL
WITHOUT
BASE SETUP
Infants may have difficulty breathing when in a sitting position. Make sure the seat is reclined properly so that your child’s head does not fall forward.
Failure to properly recline the Child Restraint could increase the child’s risk of serious injury or death.
NEVER
install Child Restraint without Base using a non-locking vehicle belt. The installation will NOT be secure. Refer to your vehicle owner's manual for detailed vehicle belt information.
LEVEL
See page 16 for "Vehicle Seating Positions" before installing. Make sure the vehicle is on a level surface. Place Child Restraint on selected vehicle seat with child properly secured in Child Restraint (See securing your child on page 66). Make sure it is not blocking the vehicle seat belt buckle.
Position Child Restraint so that the Level Line (located on the seat label) is LEVEL with the ground.
If needed, use a rolled up towel to help level the Child Restraint properly.
Installation Options:
• Lap-Shoulder Belt installation continued on page 54
• Lap Belt Only installation continued on page 62
2
INSTALL
WITHOUT
BASE SETUP
Level Line
(Seat Label)
3
53
54
1
2
INSTALL USING LAP-SHOULDER BELT
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite side of the Child Restraint. Buckle the vehicle seat belt. Pull out all of the shoulder belt webbing and activate the locking mode of the vehicle belt.
If belt does not lock, do not use that seating position to install the carrier.
1
INSTALL USING LAP-SHOULDER BELT
2
CLICK!
55
56
INSTALL USING LAP-SHOULDER BELT
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line on Carrier is level with ground.
3
While pushing down on the Carrier, pull up on the vehicle shoulder belt to remove all slack from vehicle lap belt.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall forward. If necessary re-adjust recline and repeat installation steps to make sure Child Restraint is installed properly.
Check installation before every use!
3
INSTALL USING LAP-SHOULDER BELT
CHECK YOUR WORK
57
58
4
5
INSTALL USING SHOULDER BELT GUIDE
An optional Shoulder Belt Guide is on the back of the Child Restraint.
The Guide offers additional stability when installing your Child
Restraint without the Base using the Lap/Shoulder Belt. Make sure your vehicle seat belts have enough length to allow you to properly install the
Child Restraint using the Shoulder Belt Guide.
With the Child Restraint placed and buckled without the Base and using the vehicle lap-shoulder belt in un-locked mode - pull the shoulder belt out and slide it around the back of the Child Restraint.
Thread the shoulder belt through the Shoulder Belt Guide. Then guide the shoulder belt around the carrier. Switch the shoulder belt into locked mode. Do not use this seating position if the vehicle belt does not lock.
4
INSTALL USING SHOULDER BELT GUIDE
5
59
60
INSTALL USING SHOULDER BELT GUIDE
6
While pushing down on the Child Restraint, pull up on the vehicle shoulder belt to remove all slack from the vehicle lap and shoulder belt.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall forward. If necessary re-adjust recline and repeat installation steps to make sure Child Restraint is installed properly.
Check installation before every use!
6
INSTALL USING SHOULDER BELT GUIDE
CHECK YOUR WORK
61
62
1
2
INSTALL USING LAP BELT ONLY
Thread vehicle seat belt up and slide into the Seat Belt Guide on the side of the Child Restraint.
Pull vehicle seat belt down and slide into the Seat Belt Guide on opposite side of the Child Restraint. Buckle the vehicle seat belt.
1
INSTALL USING LAP BELT ONLY
2
Seat Belt
Guide
CLICK!
63
64
INSTALL USING LAP BELT ONLY
Put the vehicle seat belt in the locked mode, see vehicle owner's manual for more information. A tightly rolled towel may be used under the front edge of the
Carrier if needed to adjust the angle of the Carrier. Angle is correct when level line on Carrier is level with ground.
3
While pushing down on the Child Restraint, pull up on the loose end of the vehicle lap belt to remove all slack.
CHECK YOUR WORK
Hold Child Restraint at each side and pull side to side and forward.
Child Restraint should not move more than 1” (25 mm) from vehicle seat back or side-to-side.
Make sure Child Restraint is level. Make sure infant’s head does not fall forward. If necessary re-adjust recline and repeat installation steps to make sure Child Restraint is installed properly.
Check installation before every use!
3
INSTALL USING LAP BELT ONLY
CHECK YOUR WORK
65
66
SECURING CHILD WITH HARNESS
For a better fit in the Carrier with smaller infants, the provided Newborn
Positioner may be needed. See page 78 for more details.
1
2
3
Loosen harness by pressing the Adjuster Button and pulling out on both
Harness Straps.
Press the button on the buckle and release both buckle tongues.
Separate chest clip and spread Harness Straps apart. Place child in carrier in seated position.
Child must be resting against back and bottom of carrier. Make sure child is not slouched.
1
2
SECURING CHILD WITH HARNESS
3
67
68
4
SECURING CHILD WITH HARNESS
Pull up on the Head Rest Adjustment Tab and adjust the Head Rest up or down until the harness slots are AT or JUST BELOW top of child's shoulders. Pull up and push down on the Head Rest to make sure the Head
Rest locks into position before tightening Harness.
NEVER
use clothing or blankets that interfere with fastening or tightening the harness. An unsecured child could be ejected in a sharp turn, sudden stop or crash!
5
Pull Harness Straps over child's shoulders and pull waist straps around their waist.
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
4
SECURING CHILD WITH HARNESS
5
*
AT OR JUST BELOW
69
70
SECURING CHILD WITH HARNESS
6
7
Insert each Buckle Tongue into Harness Buckle; listen for a click
(6a)
. Pull up firmly on both Buckle Tongues to make sure that they are securely latched
(6b)
.
Fasten Chest Clip by snapping both sides together.
Harness Straps must be laying flat, free of twists and on top of child's shoulders.
6a
CLICK!
SECURING CHILD WITH HARNESS
6b
7
CLICK!
71
72
SECURING CHILD WITH HARNESS
Pull excess strap up through buckle tongues so that harness is snug around child's thighs.
8
9
Tighten the harness by pulling slowly on Harness Adjuster Strap while pulling up on both shoulder straps to remove all slack from below
(8a)
.
Make sure the Harness Straps are snug on child. If you can pinch a fold in the Harness Strap at the child’s shoulders, harness is too loose
(8b)
. If the
Harness Straps are too loose pull the Harness Adjuster Strap more.
Move the Shoulder Pads up to the child’s shoulders. Slide Chest Clip up to center of child’s chest, level with the armpits.
WARNING
- If harness is not snug around your child, child could be ejected in a sharp turn, sudden stop or crash resulting in serious injury or death.
8a 8b
SECURING CHILD WITH HARNESS
9
73
SECURING CHILD CHECKLIST
Harness Straps must be snug. If you can pinch a fold in the strap at the shoulders, the harness is too loose. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position.
SECURING CHILD CHECKLIST
Check the position of Chest Clip: Chest Clip should be centered on the child’s chest, level with the armpits.
Never secure child in Carrier with child dressed in bulky garments or heavy clothing.
Heavy clothing can prevent harness from being properly tightened around child.
Never secure child in Carrier with child wrapped in a blanket. To keep child warm, place a blanket over child AFTER you have properly secured and tightened harness around child.
74
To ensure a better fit for smaller infants, the Newborn Positioner may be needed. Never place extra padding under or behind the child. Only use the Newborn Positioner. Never use
Newborn Positioner if child weighs more than 11 pounds (5 kg).
Straps must lay flat, free of twists and centered on top of the child’s shoulders.
Check the height of the Harness Straps: Position the Harness Straps at or just below the child’s shoulders.
*
NO Bulky Clothing
75
76
BASE RELEASE HANDLE
RELEASE CARRIER FROM BASE:
To unhook the Carrier from the Base, squeeze the Base Release Handle on the back of the Carrier then lift up on the Carry Handle.
LATCH STORAGE
Store LATCH Connectors properly in the compartments when not using for installation.
Store both LATCH Connector in compartments on either side of the Base when not in use.
1
Insert LATCH Connectors into the storage compartments.
2
Pull on the LATCH Pull Strap to secure LATCH Connectors in the compartments.
3
Roll LATCH Pull Strap and store in Pull Strap Storage Compartment.
1 2 3
77
78
1
2
3
NEWBORN POSITIONER
WARNING
- Use the NEWBORN POSITIONER provided for infants who weigh between 4 and 11 lbs (1.8 and 5 kg).
To ensure a better fit for smaller infants, the Newborn Positioner may be needed.
Do NOT use any other newborn positioner or pillows. Only use the one provided by Chicco for this Child Restraint.
Place the Newborn Positioner in the Carrier seat. Then pull the Buckle through slot in the bottom of Newborn Positioner.
Pull both Harness Straps over the side panels of Newborn Positioner.
Push Newborn Positioner firmly into Carrier to make sure it is properly positioned against the back of the seating area.
1
3
NEWBORN POSITIONER
2
79
80
HEAD REST INSERT
To provide head support for smaller infants, the Head Rest Insert may be used.
The Head Rest Insert can be used with or without the Newborn Positioner.
1
2
To Install Head Rest Insert, hold the Insert in place. Wrap the straps around the back of the Head Rest fabric.
Attach both straps to the back of the Head Rest fabric using the hook and loop tabs.
1 2
HANDLE POSITIONS
To Adjust Handle, press the Handle Release Button on one side and rotate the handle.
There are 3 positions:
BE SURE handle is locked in the “carry position” before lifting carrier by handle. An unlocked handle could move unexpectedly, causing injury to child.
Carrying Position Stationary Position Rocking Position
ALWAYS place handle in one of the LOCKED positions when using Child Restraint in vehicle.
81
82
1
ADJUSTING CROTCH STRAP
Adjust Crotch Strap if strap is underneath child.
REMOVING CROTCH STRAP:
Flip the Carrier upside-down and locate the Crotch Strap Retainer. Turn
Retainer slightly on underside of seat and insert corner through slot
(1a)
.
Flip the Carrier upright and pull Crotch Strap up through the slot
(1b)
.
NEVER
use Child Restraint without the Crotch Strap securely installed.
2
3
ADJUSTING CROTCH STRAP:
Reverse the removing instructions above to reinstall. There are two positions on the Carrier, as shown.
Make sure Crotch Strap Retainer lays flat against the bottom of the Child
Restraint. Pull on Crotch Strap to make sure it is secure.
DO NOT USE
Child Restraint if any part of the harness is damaged. For proper removal and installation of the harness straps visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
1a
ADJUSTING CROTCH STRAP
1b
2
Position 2
Position 1
3
83
CANOPY
ADJUSTING CANOPY:
The Canopy can be adjusted by rotating the canopy forwards or backwards.
1
84
1
2
REMOVING CANOPY:
Press button on Canopy Mount and pull up to remove. Repeat for the other side.
ATTACHING CANOPY:
Insert both of the Canopy Mounts into the slots on the side of the Carrier. The Canopy
Mounts will click into place.
2
INSTALLATION ON AN AIRCRAFT
When traveling by airplane with your child, Chicco recommends taking the Carrier on the airplane with you so that you can use it with your child. Not only will it protect your child during take-off, landing, and turbulence, but also allow your child to be more comfortable.
• This Child Restraint is certified for use on aircraft. Contact the
airline prior to travel to discuss their Child Restraint policy.
• Use this Child Restraint only on FORWARD-FACING aircraft seats.
• Install Carrier on an aircraft the same way it is installed in a
vehicle when using a vehicle lap belt. Reference Without Base
Installation Lap Belt ONLY on page 62.
85
86
CLEANING AND MAINTENANCE
DO NOT USE BLEACH
, solvents or household cleaners as they may weaken plastics and straps.
DO NOT USE SOAPS OR LUBRICANTS on Buckle or
LATCH hardware. It may cause them to malfunction.
•
Fabrics may be spot-cleaned, hand or machine washed:
Hand wash using mild soap and water, or machine washed in cold
water on delicate cycle using mild detergent. Hang to dry.
NEVER
use Child Restraint without the seat pad.
For softgood removal instructions visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
•
Cleaning Shoulder Pads:
Hand wash using mild soap and water. Hang to dry.
•
Cleaning Plastics:
Sponge clean using warm water and mild soap. Towel dry.
CLEANING AND MAINTENANCE
•
Cleaning Harness:
Sponge clean using warm water and mild soap. Air dry.
Do NOT machine wash.
DO NOT USE
Child Restraint if any part of the harness is damaged. For proper removal and installation of the harness straps visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
•
Cleaning LATCH Straps:
LATCH Straps cannot be replaced. Sponge clean using
warm water and mild soap. Air dry.
•
Cleaning Buckle and LATCH Hardware:
Sponge clean, using warm water only. If there is debris in the
buckle, remove and rinse in warm cup of water. Air dry.
See page 82 for removal instructions.
Do
NOT
remove LATCH or Harness Adjuster Straps. For additional information visit the Chicco website at www.chiccousa.com or call 1-877-424-4226.
87
PMS 2747 and PMS 186
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement