Schumacher USB Power Source and Compressor MF183 Operator's Manual
Schumacher USB Power Source and Compressor MF183 is a powerful and versatile tool that can jump start your vehicle, power your 12V DC devices, and inflate your tires. It features a built-in air compressor, a 12V DC power outlet, and a USB charging port, making it an indispensable asset for any vehicle owner. You can also use it as an emergency power source for your home or campsite.
Advertisement
Advertisement
1150 Peak Amp Jump Starter,
AC/DC/USB Power Source and Compressor
260-9518
To Reduce The Risk Of Injury, User Must Read And
Understand Operator’s Manual. Save These Instructions For Future Reference.
0099002192-01
TABLE OF CONTENTS
Safety Symbols ...............................................................................Page 3
Safety Information ..........................................................................Page 4
Important Safety Instructions .......................................................Page 5
Personal Safety Precautions..........................................................Page 6
Charging the Internal Battery of the Jump Starter .......................Page 6
Operating Instructions ....................................................................Page 7
Maintenance Instructions ............................................................Page 10
Moving and Storage Instructions ................................................Page 10
Troubleshooting ............................................................................Page 10
Specifications ...............................................................................Page 11
Replacement Parts .......................................................................Page 11
Accessories ...................................................................................Page 11
Warranty ........................................................................................Page 12
SAFETY SYMBOLS
Some of the following symbols may be used on your jump starter. Please study them and learn their meaning. Proper interpretation of these symbols will allow better and safer operation of the jump starter.
Symbol Name
V Volts
A Amperes
Hz
W
~
Hertz
Watts
Alternating current
Direct current
Class II construction
Read the operator’s manual
Wear safety glasses
Warning symbol
Electric shock symbol
Explosive gas symbol
Designation/Explanation
Voltage
Current
Frequency
Power
Type of current
Type or characteristic of current
Double-insulated construction
To reduce the risk of injury, read and understand the operator’s manual
Operation of the jump starter can result in damage to unprotected eyes
Alerts user to warning message
Connect only to properly grounded outlets. Replace defective cords or wire immediately.
Risk of explosive gases during normal operation of a lead-acid battery
Page 3
SAFETY INFORMATION
The purpose of safety symbols is to attract our attention to possible dangers. The safety symbols, and the explanations with them, deserve your careful attention and understanding. The symbol warnings do not by themselves eliminate any danger.
The instructions and warnings they give are no substitutes for proper accident prevention measures.
Be sure to read and understand all safety instructions in this manual, including all safety alert symbols, such as “DANGER”, “WARNING” and
“CAUTION” before using this jump starter. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.
SYMBOL MEANING
SAFETY ALERT SYMBOL:
Indicates DANGER, WARNING or CAUTION.
May be used in conjunction with other symbols or pictographs.
Failure to obey this safety warning WILL result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
Failure to obey this safety warning CAN result in death or serious injury to yourself or to others. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
Failure to obey this safety warning MAY result in personal injury to yourself or others, or property damage. Always follow the safety precautions to reduce the risk of fire, electric shock and personal injury.
CONTAINS SEALED, NON-SPILLABLE LEAD-ACID BATTERY.
MUST BE DISPOSED OF PROPERLY.
WARNING:
Possible explosion hazard. Contact with battery acid may cause severe burns and blindness. Keep out of reach of children.
Page 4
1. IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS.
RISK OF EXPLOSIVE GASES.
WORKING IN THE VICINITY OF A
LEAD-ACID BATTERY IS DANGEROUS.
BATTERIES GENERATE EXPLOSIVE
GASES DURING NORMAL OPERATION.
IT IS IMPORTANT THAT YOU FOLLOW
THESE INSTRUCTIONS EACH TIME
YOU USE THE UNIT.
To reduce the risk of battery explosion, follow these instructions and those published by the battery manufacturer and the manufacturer of any equipment you intend to use in the vicinity of a battery.
Review cautionary markings on these products and on the engine.
RISK OF ELECTRIC SHOCK OR FIRE.
1.1
Keep out of reach of children.
1.2
Do not disassemble the jump starter.
Take it to a qualified service professional if service or repair is required.
Incorrect assembly may result in fire or electrical shock.
1.3
Do not use the jump starter to jump a vehicle while charging the internal battery.
1.4
Do not recharge the jump starter with a damaged USB cable.
1.5
The jump starter gets hot during charging and must have proper ventilation.
1.6
Do not set the jump starter on flammable materials, such as carpeting, upholstery, paper, cardboard, etc.
1.7
Place the jump starter as far away from the battery being jumped as the cables will permit.
1.8
Do not expose the jump starter to rain or snow.
1.9
Never attempt to jump start a frozen battery.
1.10
Never place the jump starter directly above battery being jumped.
1.11
To prevent arcing, never allow the clamps to touch together or to contact the same piece of metal.
1.12
Use of an attachment not recommended or sold by the jump starter manufacturer may result in damage to the unit or personal injury.
1.13
Never operate the jump starter if it is damaged.
1.14
If someone else uses the jump starter, ensure they are well informed on how to use it safely, and have read and understood the operating instructions.
1.15
The jump starter is NOT designed to be installed as a replacement for a vehicle battery.
1.16
Use ONLY on vehicles, boats and garden tractors powered with a 12V DC battery system.
1.17
If the engine fails to start after the recommended number of attempts, disconnect the unit and look for other problems that may need to be corrected.
1.18
Use the jump starter for jump starting lead-acid batteries only. Do not use for dry cell batteries that are commonly used with home appliances.
Page 5
2. PERSONAL SAFETY PRECAUTIONS
2.1 Restrictions on Use:
The inverter may not be used with life support devices or systems. Failure of this inverter can reasonably be expected to cause failure of that life support device or system, or to affect the safety or effectiveness of that device or system.
2.2
Wear complete eye protection and protective clothing when working near lead-acid batteries. Always have someone nearby for help.
2.3
Have plenty of fresh water, soap and baking soda nearby for use, in case battery acid contacts your eyes, skin, or clothing. Wash immediately with soap and water and seek medical attention.
2.4
If battery acid comes in contact with eyes, flush eyes immediately for a minimum 10 minutes and get medical attention.
2.5
Neutralize any acid spills thoroughly with baking soda before attempting to clean up.
2.6
Remove all personal metal items from your body, such as rings, bracelets, necklaces and watches. A battery can produce a short circuit current high enough to weld a ring to metal, causing a severe burn.
2.7
Never smoke or allow a spark or flame in the vicinity of the battery or engine.
3. CHARGING THE INTERNAL BATTERY OF THE JUMP STARTER
IMPORTANT: CHARGE IMMEDIATELY
AFTER PURCHASE, AFTER EACH USE
AND EVERY 30 DAYS, TO KEEP THE
JUMP STARTER’S INTERNAL BATTERY
FULLY CHARGED AND PROLONG BAT-
TERY LIFE.
CHECKING THE LEVEL OF THE
INTERNAL BATTERY
To check the internal battery’s charge status, Press the
Select
button until the
Battery % LED
lights. The Digital Display will show the battery’s percent of charge.
Charge the internal battery if the display shows it is under 100%.
NOTE:
The internal battery’s percent of charge is most accurate when the jump starter has been disconnected from all devices and charging sources for a few hours.
CHARGING THE INTERNAL BATTERY
Charge the unit’s internal battery using an extension cord (not included).
NOTE:
Use of an improper extension cord could result in a risk of fire and electric shock.
1.
To charge, flip the AC connector on the back of the unit DOWN and plug in an 18 AWG or larger extension cord.
2.
Plug the extension cord into a 120VAC electrical wall outlet.
Page 6
3.
While the jump starter is charging, the marching dashes will show on the digital display. When the internal battery is fully charged, the display will show a smaller, pulsing ioo
, for energy efficiency. Complete charging may take up to 72 hours.
4.
When the internal battery is fully charged, the charger will automatically go into maintain mode and maintain the battery at full charge without damaging it. When in maintain mode, the
Battery % LED will pulse,
as long as there is an AC cord connected to the charging port.
5.
Charge the jump starter as soon as possible after use.
CHARGING THE INTERNAL
BATTERY WHILE DRIVING
You may also charge the internal battery while driving, using a male-to-male charger cable (part number 94500109 – sold separately).
IMPORTANT: DO NOT CHARGE INTERNAL
BATTERY FOR MORE THAN 30 MINUTES
OR LEAVE THE BATTERY UNATTENDED.
IT COULD EXPLODE, CAUSING PROP-
ERTY DAMAGE OR PERSONAL INJURY.
1.
Make sure the car is running.
2.
Insert one end of the accessory cable into the 12V DC power outlet.
3.
Insert the other end of the accessory cable into the vehicle’s accessory outlet (lighter socket).
NOTE:
The
Battery % LED
does not operate during this method of charging. Using this method to charge the battery overrides the maintain mode and the battery can be overcharged.
4.
Monitor the progress of the charge by pressing the Select button until the
Battery % LED lights. When the battery is fully charged, disconnect the accessory cable from the jump starter then from the lighter socket of the vehicle.
NOTE:
Completely disconnect the charger cable when the engine is not running.
4. OPERATING INSTRUCTIONS
DIGITAL DISPLAY
To check the jump starter’s internal battery status, push the
Select
button. The display will show the percent of charge of the internal battery.
When connected to the vehicle with the
Jump Start ON/OFF switch in the OFF position, the display shows the vehicle’s battery voltage. When connected and in the ON position, the display shows the equalized voltage between the vehicle’s battery and internal battery.
JUMP STARTING A VEHICLE
IMPORTANT:
Using the jump starter without a battery installed in the vehicle will damage the vehicle’s electrical system.
1.
Turn the ignition OFF.
2.
Lay the DC cables away from any fan blades, belts, pulleys and other moving parts.
3.
For a negative-ground vehicle (as in most vehicles), connect the unit’s POS-
ITIVE (RED) clamp to the POSITIVE
(POS, P, +) battery post. Next, connect the NEGATIVE (BLACK) clamp to the vehicle chassis or engine block, away from the battery.
4.
For a positive-ground vehicle, connect the unit’s NEGATIVE (BLACK) clamp to the NEGATIVE (NEG, N, -) battery post.
Next, connect the POSITIVE (RED) clamp to the vehicle chassis or engine block away from the battery.
IMPORTANT:
If you have connected the clamps backwards, an audio alarm will sound. DO NOT turn the ON/OFF switch to the ON position. This could cause serious damage to the jump starter or the vehicle. Reverse the connections and the audio alarm will stop.
5.
Turn the switch to the ON position
6.
Crank the engine for no more than 8 seconds. If the engine does not start, wait 2 minutes before cranking again.
7.
After the engine starts, turn the switch to the OFF position and remove the unit from the battery.
8.
Charge the unit.
USING THE WORK/
EMERGENCY LIGHT
1.
Position the jump starter on a flat, stable surface near the intended work area.
2.
Ensure that the battery clamps are securely clipped on the storage holders.
3.
Press the light switch once. The jump starter light will turn on and illuminate your work area.
4.
Press the light switch again. The light will flash.
5.
When finished, press the light switch again, to turn off the light.
6.
Charge the jump starter as soon as possible after using the work light.
NOTE:
The work/emergency light will automatically shut off after 24 hours.
POWERING A 12V DC DEVICE
The unit is a power source for all 12V DC accessories that are equipped with a 12V accessory plug. Use it for power outages and on fishing or camping trips. Estimated usage time is listed in the following chart.
Page 7
NOTE:
Do not power a 12V device with the unit while charging the internal battery.
1.
Make sure the device to be powered is
OFF before inserting the 12V DC accessory plug into the 12V DC accessory outlet.
2.
Ensure that the battery clamps are securely clipped on the storage holders.
3.
Open the protective cover of one of the two DC power outlets on the front of the jump starter.
4.
Plug the 12V DC device into the DC power outlet, and turn the 12V DC device on (if required).
5.
When finished, turn off the DC device
(if required) and unplug from the DC power outlet.
Do not use the unit to run appliances that draw more than 15A DC.
NOTE:
Extended operation of a 12V DC device may result in excessive battery drain. Recharge the unit immediately after unplugging the 12V DC device.
ESTIMATED RUN-TIMES
APPLIANCE TYPE
EST
WATTAGE
APPROX.
USAGE
Cell phone, fluorescent light
Radio, fan, depth finder
Camcorder
Electrical tool
Electric cooler
Car vacuum, air compressor
4 watts
9 watts
15 watts
24 watts
14.4 hrs
9 hrs
48 watts 4.5 hours
80 watts
54 hrs
24 hrs
2.7 hrs
NOTE:
Actual time may vary. Times are based on the internal battery being fully charged.
USING THE USB PORT
The USB port provides up to 2.1A at 5V DC.
1.
Ensure the battery clamps are securely clipped on the storage holders.
2.
Plug the device into one of the two
USB ports on the front panel.
3.
Press the USB port ON/OFF button.
4.
Turn on the USB device.
5.
When you are finished using the USB port, press the button, to turn off.
6.
Charge the unit.
NOTE:
To protect your electronic devices, the USB will automatically shut off when the internal battery’s charge is low.
USING THE AIR COMPRESSO
R
Read the instructions of the product being inflated before using the compressor. Avoid overinflation; do not exceed the manufacturer’s recommended pressures. Do not leave the air compressor unattended during use.
1.
Remove the air compressor hose from the storage compartment in the back of the jump starter.
2.
Connect the adapter to the valve stem by threading it onto the end. If necessary, use one of the additional adapters.
3.
Press the
Select
button, and choose
Compressor
.
4.
To select the desired PSI, press then press ON/OFF.
5.
When the desired pressure is reached, the compressor will turn off. Remove the connector from the valve stem.
6.
Do not run for more than 10 minutes at a time. Allow the jump starter to cool down for 10 minutes before using again.
7.
Wrap the compressor hose around the cleats when it is not being used.
8.
Allow unit to cool.
9.
Recharge the unit before storing.
NOTE:
To prevent overheating, the compressor has built-in thermal protection that will turn the compressor off before it overheats. If the compressor shuts off, wait a few minutes and it will automatically restart when the compressor cools.
NOTE:
When not in use, the compressor will automatically shut off after 2 minutes.
NOTE:
The air compressor is rated for
100 PSI maximum.
ESTIMATED TIME FOR INFLATING
Vehicle tires 13-16"
Bike tires
5-8 minutes
1-3 minutes
Sports balls 30 seconds
These times are approximate. Use the air compressor gauge to ensure the proper pressure has been reached. Do not overinflate.
Page 8
USING THE INVERTER
It is important to know the continuous wattage of the device you plan to use with the inverter. The Portable Power must be used with devices drawing 400 watts or less. If the wattage is not marked on the device, use only devices that draw less than 3.3 amps of AC current.
Devices like TVs, fans or electric motors require additional power to start (commonly known as the “starting or peak power”). The Portable Power can supply a momentary surge in wattage; however even devices rated less than the maximum 400 watts can exceed the inverter’s surge capability and cause an automatic overload shutdown.
Do not use the inverter with a product that draws a higher wattage than the inverter can provide, as this may cause damage to the inverter and the product.
Make sure the device you are using is compatible with a modified sine wave inverter.
Always run a test to establish whether the inverter will operate a particular piece of equipment or device.
In the event of a power overload, the inverter is designed to automatically shut down. This safety feature prevents damaging the inverter while testing devices and equipment with the 400-watt range.
If powering more than one device, start one device at a time to avoid a power surge and/or inverter overload. The surge load of each device should not exceed the inverter’s Continuous Operation wattage rate.
IMPORTANT: If you are using the power inverter to operate any type of battery charger, monitor the temperature of the battery charger for about 10 minutes. If the battery charger becomes abnormally warm, disconnect it from the inverter immediately.
You can use an extension cord from the inverter to the device without significantly decreasing the power being generated by the inverter. For best operating results, the extension cord should be 16 AWG
(1.31 mm
2
) or larger and no longer than
50 feet.
IMPORTANT:
This inverter uses a modified sine waveform, which is not quite the same as power company electricity. For the following devices, we strongly recommend that you use caution and check the device’s manual to make sure it is compatible with modified sine waveform.
1.
Switch mode power supplies
2.
Linear power supplies
3.
Class 2 transformers
4.
Line filter capacitors
5.
Shaded pole motors
6.
Fan motors
7.
Microwave ovens
8.
Fluorescent and high-intensity lamps
(with a ballast)
9.
Transformerless battery chargers
Using the inverter with any of these devices may cause the device to run warmer or overheat.
POWERING A 110V AC DEVICE
1.
Ensure the battery clips are securely on the storage holders.
2.
Open the protective cover of the AC power outlet on the front panel.
3.
Make sure the 110V AC device to be operated is turned OFF.
4.
Plug the 110V AC device into the AC power outlet and press the
Select
button, to choose
AC Inverter
.
5.
Turn the device on.
6.
Charge the unit as soon as possible after each use.
RISK OF ELECTRIC SHOCK.
Incorrect operation of your inverter may result in damage and personal injury. The inverter output is 110V AC and can shock or electrocute the same as any ordinary household AC wall outlet.
NOTE: The maximum continuous load is
400 watts. Do not use the inverter with a product that draws more than 400 watts, as this may cause damage to the inverter and the product.
Page 9
5. MAINTENANCE INSTRUCTIONS
• After use and before performing maintenance, unplug and disconnect the jump starter.
• Use a dry cloth to wipe all battery corrosion and other dirt or oil from the battery clips, cords and the jump starter case.
• Ensure that all of the jump starter components are in place and in good working condition.
• All servicing should be performed by qualified service personnel.
6. MOVING AND STORAGE INSTRUCTIONS
• Store inside, in a cool, dry place.
• Do not store the clips on the handle, clipped together, on or around metal, or clipped to cables. The clips on the jump starter are live when the switch is in the ON position and will produce arcing or sparking if they come in contact with each other. To prevent accidental arcing, always place the switch in the
OFF position and keep the clips on the storage holders when not using it to jump start a vehicle.
• If the jump starter is moved around the shop or transported to another location, take care to avoid/prevent damage to the cords, clips and jump starter. Failure to do so could result in personal injury or property damage.
IMPORTANT:
Do not use and/or store the jump starter in or on any area or surface where damage could occur if the internal battery should unexpectedly leak acid.
IMPORTANT:
• CHARGE IMMEDIATELY AFTER
PURCHASE
• KEEP FULLY CHARGED
Charge the jump starter’s internal battery immediately after purchase, after every use and every 30 days.
All batteries are affected by temperature. The ideal storage temperature is at 70°F. The internal battery will gradually self-discharge (lose power) over time, especially in warm environments.
Leaving the battery in a discharged state may result in permanent battery damage. To ensure satisfactory performance and avoid permanent damage, charge the internal battery every month.
7. TROUBLESHOOTING
PROBLEM
The jump starter won’t jump start my car.
POSSIBLE CAUSE
The Jump Start switch is not turned ON.
SOLUTION
Turn ON the Jump Start switch.
The clamps are not making a good connection to the battery.
Check for poor connection to battery and frame.
Make sure connection points are clean.
The jump starter’s battery is not charged.
The vehicle’s battery is defective.
Check the battery charge status by pressing the
Select
button on the front of the unit. See Digital
Display section.
Have the battery checked.
Page 10
PROBLEM
The unit won’t power my
12V device.
The internal battery won’t hold a charge.
The jump starter’s alarm is on.
The inverter is on, but the display only shows err .
The compressor shuts off before reaching the set pressure.
POSSIBLE CAUSE
The 12V device is not turned on.
SOLUTION
Turn on the 12V device.
The Portable Power’s battery is not charged.
Check the battery charge status by pressing the button on the front of the unit. See Digital Display section.
The 12V device draws more than 15A or has a short circuit.
The battery is bad (will not accept a charge).
Contact a qualified service technician, to replace the fuse.
Have the battery checked.
Connections are reversed.
Disconnect the jump starter and reverse the clamps.
The jump starter battery is not fully charged.
Recharge the unit.
The device is drawing more than 400W or has a short circuit.
The compressor has a thermal cutoff, to protect it from overheating.
Use only devices that draw less than 3.3 amps of
AC current.
Wait a few minutes. The compressor will start up again and finish the process.
8. SPECIFICATIONS
Internal battery type ............................... Sealed maintenance-free AGM lead-acid
Nominal voltage ............................................................................................. 12V DC
USB output ..............................................................................................5V DC, 2.1A
Jump start ...............................................................................................1150A peak
9. REPLACEMENT PARTS
Air compressor accessory kit (3 hose adapters) ................................ 2299001425Z
10. ACCESSORIES
Male-to-male accessory cable .................................................................. 94500109
Page 11
1. WARRANTY
1150 Peak Amp Jump Starter, AC/DC/USB
Power Source and Compressor
WARRANTY
90-DAY MONEY BACK GUARANTEE
This MASTERFORCE™ brand jump starter carries our 90-Day Money Back
Guarantee. If you are not completely satisfied with your MASTERFORCE™ brand product for any reason within ninety (90) days from the date of purchase, return the item with your original receipt to any MENARDS
®
retail store, and we will provide you a refund – no questions asked.
3-YEAR LIMITED WARRANTY
This MASTERFORCE™ brand jump starter carries our famous No Hassle 3-Year
Limited Warranty to the original purchaser. If, during normal use, this MASTER-
FORCE™ product breaks or fails due to a defect in material or workmanship within three (3) years from the date of original purchase, simply bring the item with the original sales receipt back to your nearest MENARDS
®
retail store. At its discretion, MASTERFORCE™ agrees to have the item or any defective part(s) repaired or replaced with the same or similar MASTERFORCE™ product or part free of charge, within the stated warranty period, when returned by the original purchaser with original sales receipt. Not withstanding the foregoing, this limited warranty does not cover any damage that has resulted from abuse or misuse of the Merchandise. This warranty: (1) excludes expendable parts including but not limited to blades, brushes, belts, bits, light bulbs, and/or batteries; (2) shall be void if this product is used for commercial and/or rental purposes; and (3) does not cover any losses, injuries to persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary from state to state. Be careful, jump starters are dangerous if improperly used or maintained. Seller’s employees are not qualified to advise you on the use of this merchandise. Any oral representation(s) made will not be binding on seller or its employees. The rights under this limited warranty are to the original purchaser of the merchandise and may not be transferred to any subsequent owner. This limited warranty is in lieu of all warranties, expressed or implied including warranties or merchantability and fitness for a particular purpose. Seller shall not be liable for any special, incidental, or consequential damages. The sole exclusive remedy against the seller will be for the replacement of any defects as provided herein, as long as the seller is willing or able to replace this product or is willing to refund the purchase price as provided above. For insurance purposes, seller is not allowed to demonstrate any of these products for you.
For questions/comments, technical assistance or repair parts—
Please call toll free at:
1-800-621-5485.
Page 12
NOTES
Page 13
Page 14
NOTES
NOTES
Page 15
© 2020 Menard, Inc., Eau Claire, WI 54703
05/2020

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Jump-starts vehicles with up to 1000 amps of power
- Inflates tires up to 120 PSI
- Charges electronic devices via USB
- Built-in LED flashlight for emergencies
- Compact and lightweight design for easy storage