Innova 3020d Owner's manual

Innova 3020d Owner's manual
Table of Contents
i
SAFETY PRECAUTIONS
SAFETY FIRST! .......................................................................
1
ABOUT THE CODE READER
CONTROLS AND INDICATORS .............................................
DISPLAY FUNCTIONS ............................................................
3
4
USING THE CODE READER
CODE RETRIEVAL PROCEDURE ..........................................
VIEWING ABS DTCs ...............................................................
ERASING DIAGNOSTIC TROUBLE CODES (DTCs) .............
7
9
10
WARRANTY AND SERVICING
LIMITED ONE YEAR WARRANTY ..........................................
SERVICE PROCEDURES .......................................................
13
13
Safety Precautions
SAFETY FIRST
SAFETY FIRST!
To avoid personal injury, instrument damage and/or
damage to your vehicle.
This manual describes common test procedures used
by experienced service technicians. Many test procedures
require precautions to avoid accidents that can result in
personal injury, and/or damage to your vehicle or test
equipment. Always read your vehicle's service manual and
follow its safety precautions before and during any test or
service procedure. ALWAYS observe the following general
safety precautions:
When an engine is running, it produces carbon monoxide,
a toxic and poisonous gas. To prevent serious injury or
death from carbon monoxide poisoning, operate the
vehicle ONLY in a well-ventilated area.
To protect your eyes from propelled objects as well as hot
or caustic liquids, always wear approved safety eye
protection.
When an engine is running, many parts (such as the
coolant fan, pulleys, fan belt etc.) turn at high speed. To
avoid serious injury, always be aware of moving parts.
Keep a safe distance from these parts as well as other
potentially moving objects.
Engine parts become very hot when the engine is running.
To prevent severe burns, avoid contact with hot engine
parts.
P RND L
Before starting an engine for testing or troubleshooting,
make sure the parking brake is engaged. Put the
transmission in park (for automatic transmission) or
neutral (for manual transmission). Block the drive wheels
with suitable blocks.
Connecting or disconnecting test equipment when the
ignition is ON can damage test equipment and the
vehicle's electronic components. Turn the ignition OFF
before connecting the Code Reader to or disconnecting
the Code Reader from the vehicle’s Data Link Connector
(DLC).
1
Safety Precautions
SAFETY FIRST
To prevent damage to the on-board computer when taking
vehicle electrical measurements, always use a digital
multimeter with at least 10 megOhms of impedance.
Fuel and battery vapors are highly flammable. To prevent
an explosion, keep all sparks, heated items and open
flames away from the battery and fuel / fuel vapors. DO
NOT SMOKE NEAR THE VEHICLE DURING TESTING.
Don't wear loose clothing or jewelry when working on an
engine. Loose clothing can become caught in the fan,
pulleys, belts, etc. Jewelry is highly conductive, and can
cause a severe burn if it makes contact between a power
source and ground.
2
About the Code Reader
CONTROLS AND INDICATORS
CONTROLS AND INDICATORS
2
5
6
7
1
3
2
4
9
Figure 1. Controls and Indicators
See Figure 1 for the locations of items 1 through 9, below.
1.
ERASE button - Erases Diagnostic Trouble Codes (DTCs) and
"Freeze Frame" data from your vehicle's computer, and resets
Monitor status.
2. DTC button - Displays the DTC View screen and/or scrolls the LCD
display to view DTCs.
3.
LINK button - When the Code Reader is connected to a vehicle,
links the Code Reader to the vehicle’s PCM to retrieve Powertrain
DTCs from the computer’s memory.
4. ABS button - Links the Code Reader to the vehicle’s ABS control
module to retrieve ABS DTCs from the computer’s memory.
5. GREEN LED - Indicates that all engine systems are running
normally (all Monitors on the vehicle are active and performing their
diagnostic testing, and no DTCs are present).
3
About the Code Reader
DISPLAY FUNCTIONS
6. YELLOW LED - Indicates there is a possible problem. A “Pending”
DTC is present and/or some of the vehicle's emission monitors have
not run their diagnostic testing.
7. RED LED - Indicates there is a problem in one or more of the
vehicle's systems. The red LED is also used to show that DTC(s)
are present. DTCs are shown on the Code Reader’s LCD display. In
this case, the Malfunction Indicator (“Check Engine”) lamp on the
vehicle's instrument panel will light steady on.
8. LCD Display - Displays test results, Code Reader functions and
Monitor status information. See DISPLAY FUNCTIONS, below, for
details.
9. CABLE - Connects the Code Reader to the vehicle's Data Link
Connector (DLC).
DISPLAY FUNCTIONS
1
16 5
13
2
4
3
7
6
10
9
11
14
15
8
12
Figure 2. Display Functions
See Figure 2 for the locations of items 1 through 16 below.
1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area.
2. Monitor icons - Indicate which Monitors are supported by the
vehicle under test, and whether or not the associated Monitor has
run its diagnostic testing (Monitor status). When a Monitor icon is
solid green, it indicates that the associated Monitor has completed
its diagnostic testing. When a Monitor icon is flashing red, it
indicates that the vehicle supports the associated Monitor, but the
Monitor has not yet run its diagnostic testing.
The I/M Monitor Status icons are associated with INSPECTION
and MAINTENANCE (I/M) READINESS STATUS. Some states
require that all vehicle Monitors have run and completed their
diagnostic testing before a vehicle can be tested for Emissions
(Smog Check). A maximum of fifteen Monitors are used on OBD2
systems. Not all vehicles support all fifteen Monitors. When the
Diagnostic Tool is linked to a vehicle, only the icons for Monitors
that are supported by the vehicle under test are visible on the
display.
4
About the Code Reader
DISPLAY FUNCTIONS
3.
Link icon - Indicates whether or not the Diagnostic Tool is
communicating (linked) with the vehicle's on-board computers.
When visible, the Diagnostic Tool is communicating with the
computers. If the Link icon is not visible, the Diagnostic Tool is not
communicating with the computers.
4.
Vehicle icon - Indicates whether or not the Diagnostic Tool is
being properly powered through the vehicle's Data Link Connector
(DLC). A visible icon indicates that the Diagnostic Tool is being
powered through the vehicle's DLC connector.
5. MIL icon - Indicates the status of the Malfunction Indicator Lamp
(MIL). The MIL icon is visible only when a DTC has commanded the
MIL on the vehicle's dashboard to light.
6. ABS icon - Indicates the currently displayed DTC is an Anti-Lock
Braking System code.
7. AIR BAG icon – Indicates the currently displayed DTC is a
Supplemental Restraint System code.
8. HISTORY icon – Indicates the currently displayed DTC is a
“History” code.
9. FREEZE FRAME icon - Indicates that “Freeze Frame” data has been
stored in the vehicle’s computer for the currently displayed DTC.
10. PENDING icon - Indicates the currently displayed DTC is a
"Pending" code.
11. PERMANENT icon - Indicates the currently displayed DTC is a
“Permanent” code.
12. DTC Display Area - Displays the Diagnostic Trouble Code (DTC)
number. Each fault is assigned a code number that is specific to that
fault.
13. Code Number Sequence - The Diagnostic Tool assigns a
sequence number to each DTC that is present in the computer's
memory, starting with "01.” This helps keep track of the number of
DTCs present in the computer's memory. Code number "01" is
always the highest priority code, and the one for which "Freeze
Frame" data has been stored.
14. Code Enumerator - Indicates the total number of codes retrieved
from the vehicle’s computer.
15. Severity - Indicates the level of severity for the priority code (code
number “1”), as follows:
Service should be scheduled and repairs made when
convenient. This DTC typically has no immediate threat to
essential system components in the short term.
Repair immediately if drivability issues are present. Threat
to essential system components if not repaired as soon as
possible.
Stop and repair vehicle immediately to prevent interrelated
failures. Harmful and damaging to essential system
components.
5
About the Code Reader
DISPLAY FUNCTIONS
16.
6
Bluetooth icon – Indicates communication status with a
compatible
Innova
mobile
application
(please
visit
www.innova.com/apps for more information). A solid blue icon
indicates an active Bluetooth connection has been established. A
solid grey icon indicates Bluetooth is not connected.
Using the Code Reader
CODE RETRIEVAL PROCEDURE
CODE RETRIEVAL PROCEDURE
Never replace a part based only on the DTC definition. Each DTC has a
set of testing procedures, instructions and flow charts that must be
followed to confirm the location of the problem. This information is found
in the vehicle's service manual. Always refer to the vehicle's service
manual for detailed testing instructions.
Check your vehicle thoroughly before performing any test.
ALWAYS observe safety precautions whenever working on a
vehicle. See SAFETY FIRST! on page 1 for more information.
1. Turn the ignition off.
2. Locate the vehicle's 16-pin Data Link
Connector (DLC).
3. Connect the Code Reader’s cable
connector to the vehicle's DLC. The
cable connector is keyed and will only fit
one way.
„
If you have problems connecting the
cable connector to the DLC, rotate
the connector 180° and try again.
If you still have problems, check the
DLC on the vehicle and on the Code
Reader. Refer to your vehicle's
service manual to properly check the
vehicle's DLC.
„
After the Code Reader’s test
connector is properly connected to
the vehicle's DLC, the Vehicle icon
should display to confirm a good
power connection.
4. Turn the ignition on. DO NOT start the
engine.
5. The Code Reader will automatically link to the vehicle’s computer(s).
„
If the LCD display is blank, it indicates there is no power at the
vehicle's DLC. Check your fuse panel and replace any burnedout fuses.
If replacing the fuse(s) does not correct the problem, see your
vehicle's repair manual to locate the proper computer (PCM)
fuse/circuit. Perform any necessary repairs before continuing.
„
After 4-5 seconds, the Code Reader will retrieve and display
any Diagnostic Trouble Codes that are in the vehicle's computer
memory.
7
Using the Code Reader
CODE RETRIEVAL PROCEDURE
„
If Error is shown on the Code
Reader’s LCD display, it indicates
there is a communication problem.
This means that the Code Reader is
unable to communicate with the
vehicle's computer. Do the following:
-
Turn the ignition key off, wait 5
seconds and turn the key back on
to reset the computer.
-
Make sure your vehicle is OBD2 compliant.
6. Read and interpret the Diagnostic Trouble Codes using the LCD
display and the green, yellow and red LEDs.
The green, yellow and red LEDs are used (with the LCD
display) as visual aids to make it easier for the user to
determine engine system conditions.
„
Green LED - Indicates that all
engine systems are "OK" and
running normally. All monitors on the
vehicle are active and are performing
their diagnostic testing, and no
trouble codes are present. A zero will
show on the Code Reader’s LCD
display for further confirmation.
„
Yellow LED - Indicates one of the
following conditions:
PENDING CODE PRESENT - If the
yellow LED is lit, it may indicate the
existence of a pending code. Check
the Code Reader’s LCD display for
confirmation. A pending code is
confirmed by the presence of a
numeric code and the word PENDING
on the Code Reader’s LCD display. If
no pending code is shown, the yellow
LED indicates Monitor Status (see the
following).
MONITOR STATUS - If the Code
Reader’s LCD display shows a zero
(indicating there are no DTCs present
in the vehicle's computer), but the
yellow LED is lit, it indicates a
"Monitor Has Not Run" status. This
means that some of the Monitors on
the vehicle have not yet finished their
diagnostic self-testing. This condition
is confirmed by one or more blinking
Monitor icons on the LCD display. A
blinking Monitor icon means the Monitor has not yet run and
finished its diagnostic self-testing. All Monitor icons that are solid
have completed their diagnostic self-testing.
8
Using the Code Reader
VIEWING ABS DTCs
„
Red LED - Indicates there is a problem
with one or more of the vehicle's
systems. The red LED is also used to
show that DTC(s) are present (displayed on the Code Reader’s LCD
display). In this case, the Malfunction
Indicator (Check Engine) lamp on the
vehicle's instrument panel will light
steady on.
The Code Reader will display a code only if codes are
present in the vehicle's computer memory. If no codes
are present, a "0" will be displayed.
7. If more than one code is present, press and release the DTC button,
as necessary, to display additional codes.
8. When the last retrieved DTC has been displayed and the DTC
button is pressed, the Code Reader returns to the “Priority” code.
Visit the manufacturer's website for Fault Code Definitions. Match the
retrieved DTC(s) with those listed. Read the associated definition(s),
and see the vehicle's service manual for further evaluation.
VIEWING ABS DTCs
ABS functionality is supported for Chrysler, Ford, and GM
vehicles only. Visit the manufacturer’s website for a complete
list of vehicles covered.
1. If not connected already, connect the Code Reader to the vehicle's
DLC, and turn the ignition "On.” (If the Code Reader is already
connected and linked to the vehicle's computer, proceed directly to
step 3. If not, continue to step 2.)
2. Perform the Code Retrieval procedure
as described on page 7.
3. Press the ABS button. After 4-5 seconds,
the Code Reader will retrieve and
display any Diagnostic Trouble Codes
stored in the ABS controller’s memory.
„
If ABS functionality is not supported
by your vehicle, the message
“NoSUP” shows on the Code
Reader’s display.
The Code Reader will display a
code only if codes are present
in the vehicle’s computer
memory. If no codes are
present, a “0” will be displayed.
4. If more than one code is present, press and release the ABS button,
as necessary, to display additional codes.
9
Using the Code Reader
ERASING DIAGNOSTIC TROUBLE CODES
5. When the last retrieved DTC has been displayed and the ABS
button is pressed, the Code Reader returns to the “Priority” code.
„
To exit the ABS mode, press the DTC button to return to the
OBD2 mode.
Visit the manufacturer's website for Fault Code Definitions. Match the
retrieved DTC(s) with those listed. Read the associated definition(s),
and see the vehicle's service manual for further evaluation.
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
When the Code Reader’s ERASE function is used to erase
the DTCs from the vehicle's on-board computer, "Freeze
Frame" data and manufacturer-specific enhanced data are
also erased.
If you plan to take the vehicle to a Service Center for repair, DO NOT
erase the codes from the vehicle's computer. If the codes are erased,
valuable information that might help the technician troubleshoot the
problem will also be erased.
Erase DTCs from the computer's memory as follows:
When DTCs are erased from the vehicle's computer memory, the
I/M Readiness Monitor Status program resets status of all the
Monitors to a not run "flashing" condition. To set all of the Monitors
to a DONE status, an OBD2 Drive Cycle must be performed.
Refer to your vehicle's service manual for information on how to
perform an OBD2 Drive Cycle for the vehicle under test.
1. If not connected already, connect the Code
Reader to the vehicle's DLC. (If the Code
Reader is already connected and linked to
the vehicle's computer, proceed directly to
step 4. If not, continue to step 2.)
2. Turn the ignition on. DO NOT start the
engine. The Code Reader will automatically link to the vehicle’s computer.
„
To erase OBD2 DTCs: Wait until the
codes are displayed on the Code
Reader’s LCD and then proceed to
step 3.
„
To erase ABS DTCs: Press the
ABS button to retrieve codes, and
then proceed to step 3.
3. Press and release the Code Reader’s
ERASE
button. The LCD display will
indicate "SuRE?" for your confirmation.
„
10
If you change your mind and do not
wish to erase the codes, press the
DTC button to return to the code
retrieval function.
Using the Code Reader
ERASING DIAGNOSTIC TROUBLE CODES
„
If you wish to continue, press the ERASE
button again.
When all retrievable information, including DTCs, has been
cleared from the computer’s memory, the Code Reader will relink to the vehicle’s computer, and the LCD display will show "0.”
Erasing DTCs does not fix the problem(s) that caused the code(s)
to be set. If proper repairs to correct the problem that caused the
code(s) to be set are not made, the code(s) will appear again (and
the check engine light will illuminate) as soon as the vehicle is
driven long enough for its Monitors to complete their testing.
11
Notes
12
Warranty and Servicing
LIMITED ONE YEAR WARRANTY
The Manufacturer warrants to the original purchaser that this unit is free
of defects in materials and workmanship under normal use and
maintenance for a period of one (1) year from the date of original
purchase.
If the unit fails within the one (1) year period, it will be repaired or
replaced, at the Manufacturer’s option, at no charge, when returned
prepaid to the Service Center with Proof of Purchase. The sales receipt
may be used for this purpose. Installation labor is not covered under this
warranty. All replacement parts, whether new or remanufactured,
assume as their warranty period only the remaining time of this warranty.
This warranty does not apply to damage caused by improper use,
accident, abuse, improper voltage, service, fire, flood, lightning, or other
acts of God, or if the product was altered or repaired by anyone other
than the Manufacturer’s Service Center.
The Manufacturer, under no circumstances shall be liable for any
consequential damages for breach of any written warranty of this unit.
This warranty gives you specific legal rights, and you may also have
rights, which vary from state to state. This manual is copyrighted with all
rights reserved. No portion of this document may be copied or
reproduced by any means without the express written permission of the
Manufacturer. THIS WARRANTY IS NOT TRANSFERABLE. For
service, send via U.P.S. (if possible) prepaid to Manufacturer. Allow 3-4
weeks for service/repair.
SERVICE PROCEDURES
If you have any questions, require technical support or information on
UPDATES and OPTIONAL ACCESSORIES, please contact your local
store, distributor or the Service Center.
USA & Canada:
(800) 544-4124 (6:00 AM-6:00 PM PST, Monday through Saturday)
All others: (714) 241-6802 (6:00 AM-6:00 PM PST, Monday through
Saturday)
FAX: (714) 241-3979 (24 hr.)
Web: www.innova.com
13
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement