Terrazzo-Ware™
Mop Sink - Drop Front Series
TDF-24
Fixture May Show Some Available Options
Please visit www.acorneng.com
for most current specifications.
Terrazzo Drop Front Mop Sink
Mop Sink is an attractive, durable fixture designed to be easy to install and maintain. ACORN Terrazzo-Ware™ precast mop sinks provide flexibility in configuration and size as required by the design of the building and the specific installation. Custom sizes and colors are also available.
Front Shoulder is dropped 6" to allow easier bucket tipping. A stainless steel cap is provided on this dropped front shoulder for additional protection. Other shoulders are 12” high and pitched to provide drainage. Also comes standard without caps exposing the natural terrazzo finish. Optionally, they may be capped with stainless steel for protection.
Construction is one piece, precast terrazzo composed of marble chips cast in Portland cement to provide a compressive strength of at least 3,000 PSI seven days after casting. The mop sink surface is ground smooth and sealed to provide years of service.
Integral Drain is supplied with a removable, stainless steel grid strainer and provides for an inside caulked connection to a 3" pipe. The mop sink has coved corners and is pitched to the drain outlet to provide positive drainage. A beehive dome strainer is optionally available.
Tiling Flanges made of galvanized steel are provided loose as an easy to install accessory when flexibility and simplicity are desired. As an alternative, factory installed galvanized steel tiling flanges extending at least
1" above the shoulder can be specified.
Accessories to complement and complete the installation of the mop sink include:
• chrome finish faucets
• 36" hose to reduce splashing with wall hanger to support the hose
• mop hanger for easy storage of the mop over the sink
• rubber drain gaskets for easy installation of the fixture
• stainless steel wall guards to protect sensitive walls from splashing water
• tiling flanges for simple, flexible field installation
GUIDE SPECIFICATION
Provide and install an ACORN Drop Front Mop Sink (specify model number and options). Mop Sink shall be made of precast terrazzo to produce a compressive strength of at least 3,000 PSI seven days after casting. All exposed surfaces shall be ground smooth and sealed. No air holes or pits shall be allowed on the finished surface.
Sink shall have coved corners and be pitched to the drain outlet for positive drainage. Integral drain shall have a stainless steel strainer and provide for an inside caulked connection to a 3" pipe. The manufacturer will provide to the installer the necessary installation instructions.
Page 1 T.MSDF
Revised: 08/23/18
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: [email protected]
Terrazzo-Ware™ : Mop Sink - Drop Front Series
BASE MODEL, SIZE & TYPE(Must Specify) o TDF-24 24" Square Terrazzo Drop Front Mop Sink o TDF-32 32" Square Terrazzo Drop Front Mop Sink o TDF-36 36" Square Terrazzo Drop Front Mop Sink o TDF-3624 36" x 24" Rectangular Terrazzo Drop Front
Mop Sink
SUFFIX OPTIONS o - BDS Beehive Dome Strainer o - OC o - SSC
Optional Colors (contact factory)
Stainless Steel Cap
TILING FLANGES (factory installed) o - TF1 Tiling Flange, Rear Side o - TF2 Tiling Flange, Two Adjacent Sides
Specify: o Right & Rear o Left & Rear o - TF3 Tiling Flange, Three Sides
ACCESSORIES o KDG3 o KDG32 o KF
Rubber Drain Gasket for 3" Waste Pipe
Rubber Drain Gasket Reducer for 2" Waste Pipe
Tiling Flange(s) (Shipped Loose)
Specify length(s): o o
KFC
KH36 o 24" Qty:_______ o 32" Qty:_______ o 36" Qty:_______
Faucet, Chrome Finish (H & C)
Hose 36" Long with Wall Hanger o KMH o KWG o LB
Mop Hanger with 3 Grips on a Stainless Steel Bracket
Wall Guard (Shipped Loose)
Specify number of sides: o 1 Side o 2 Sides o 3 Sides
Specify length(s): o 24" Qty:_______ o 32" Qty:_______ o 36" Qty:_______
Lint Basket/Strainer
Please visit www.acorneng.com
for most current specifications.
WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Important: Installation instructions and current rough-in are furnished with each fixture. Do not rough in without certified dimensions.
Dimensions are subject to manufacturer’s tolerance of plus or minus 1/4" and change without notice. Acorn assumes no responsibility for use of void or superseded data. © Copyright 2007 Acorn Engineering Company
Selection Summary
Model No. & Option___________________________
Quantity____________________________________
Approved for Manufacturing
Company__________________Title______________
Signature_________________ Date______________
Page 2 T.MSDF
Revised: 08/23/18
Acorn Engineering Company • 15125 Proctor Avenue • P.O. Box 3527 • City of Industry, CA 91744-0527 U.S.A.
Tel: (800) 488-8999 • (626) 336-4561 • Fax: (626) 961-2200 • www.acorneng.com • E-mail: [email protected]
