USER'S MANUAL
ч о п о кое юн
CONTENTS
Install power supply..cccoviviiiiiiiiiiiici ieee eee 1
Install MoetnerDoal Ou: cms mass menes cm ms nan à ий
Install 37” and 5%” drives.........ee..eeeesseeeroa 3
Install PCI components..........eee_e.esssvesreeeeoos 5
Fan installation and Set UP .a.sssrrr 5
Connect case leads to motherboard............... 6
Complete Che Installation ======== ==> mos 6
USB/eSATA/Audio cable pin assignments............_c... 7
X-Trooper
Finished Appearance
NOTE: CPU and memory installation is not covered in this
manual. Please refer to each component's documentation
E for instructions.
1. Install power supply:
1.1 Remove thumbscrews from the 1.2 Grab the notch on the edge of the
rear of the X-Trooper on the right panel. Pull to release.
right side of the case.
-
- —
— + = — а.
pe —
Cr о =
== —
— — = = —
1.3 Install power supply below 1.4 Make sure that the power supply
mounting ledges from the inside is correctly installed, and that
of the case at the bottom. screw mount points are aligned
(as seen in step 1.5).
NOTE: Touch an unpainted metal section of the chassis to discharge
static electricity before handling PC components. An anti-static wrist
strap should also be worn to further minimize the possibility of damage.
2. Install motherboard:
f AM AM AM |
AM= | Е
EM =
0
M
eee
= (С Micro ATX : M
ATX: A
he J
= = [а (С) |
MO сн |
a
О
С
—
с
1.5 Fasten screws to the back of the 2.1 Refer to the motherboard holes
case. Keep a hand on the power index for standoff placement for
supply to keep the holes aligned. your motherboard type. A full
ATX (12"x9.6") board will use
notches listed as "A", Some
motherboards may not use all
notches. Use any notches that
line up with your motherboard.
2.2 If your motherboard included an 2,3 put standoff screws in place. Align
I/O shield, fit the shield in the motherboard with standoffs and
provided hole on the back of the mount to case. This ATX mother-
case until it clicks into place. board (12”x8.3”) only used the left
Make sure that the holes on the six notches.
shield match up with the 1/0
connectors on the motherboard.
3. Install 312” and 544” drives:
3.1 To install an optical or floppy drive, 3.2 For 5 1/4" drives, align the device
first remove the metal shield that with the drive bay and insert. Do
sits behind each drive bay cover. the same for 3 1/2” drives using
This must be done from the inside the lower drive bay.
of the case. Next remove the drive
bay covers by pinching the tab
holding both sides in place and
pushing inwards.
3.3 Remove the other side panel in 3.4 For hard-disk drives, find the
the same manner as step 1.1 mounting rails in the screw bag.
and step 1.2. Locate the Attach rails to both sides of the
indicated toolless rails and line drive.
them up with the holes in the
drive. Secure by turning the
knob to a horizontal (-)
position. You can unlock the
rail by turning the knob back to
the vertical (|) position.
3.5 Align rails with hard drive bay and 3.6 Remove the left-hand side panel in
insert. the same way as shown in step 1.1
and step 1.2. Connect the power
cables to the drive and reroute any
wiring that you want to behind
the motherboard tray.
4. Install PCI components:
4.1 First, remove the PCI slot covers. 4.2 Read your PCI expansion card's
Push on the cover at a diagonal documentation. Install PCI card
angle. Wiggle the cover until it into correct slot for your card
comes loose. Be careful as there type (x1, x16, etc.).
could be sharp edges that can
cut you.
5. Fan installation and setup:
LALALA
9 ht 444444 44 44
EA A == À Lo L A A J
Herr rrr
0000000000000 4
4.3 Once the card is seated firmly, 5.1 Inside the chassis, mount fan to
secure it with a screw in the the underside of “blowhole” area
appropriate hole. and screw into place. Follow the
same procedure for the side
fans. NOTE: You only need to
do this if you purchased the non-
windowed version.
6. Connect case leads to motherboard:
6.1 Locate the above front panel 6.2 Locate the above front panel leads.
leads. Your motherboard user's Refer to your motherboard user's
manual will provide schematics. manual for placement
The triangular markings Mon schematics. The case speaker can
the leads indicate positive wires. be found in the accessories bag.
(Remove right-side panel to better access wiring.)
7. Complete the installation:
7.1 With all components properly installed,
gently return side panels to their
original positions and replace all
SCrews.
Congratulations! You have completed
assembly of the X-Trooper!
8. USB/eSATA/Audio cable pin assignments:
X-Trooper Cable Module
ESATA
GND
TXN TXP
sv GND
GND RXP
HD AUDIO
GND BLACK —RED PORT1 L
PRESENCE# BLACK — GREEN PORT1R
SENSE1-RETURN GRAY — YELLOW PORT2 R
KEY — ORANGE SENSE-SEND
SENSE2-RETURN WHITE — BLUE PORT2 L
AC97 AUDIO
GND BLACK ——RED MIC-IN
N/C — — — GREEN MIC-POWER
LINE OUT RR YELLOW — YELLOW LINE OUT FR
KEY —N/C
LINE OUT RL BLUE —— BLUE LINE OUT FL
USB
+5V RED —— if} ORANGE +5V
DO- WHITE — HI | —— GRAY Do-
D0+ GREEN—— YELLOW DO+
GND GND+BLACK —— UE+GND GND
NIC— KEY
FIGRL FOR YOUR LUF
">
