Contents Contents Contents Contents IP-1100C - Side view camera Part No. 5961 5970 Model No. IP-1100C-C IP-1100C-FIX Quantity 1 1 Description IP Camera only - surface-mount, IP67 (1080P) 4 x M3 Fixing Screws and 1 x M3 Hex key (L Shape) (Not shown) IG 5905 IG 5971 Part #5969/#5961/5962 This guide is available in: xXxxxxx at IG www.brigade-electronics.com/productsupportarea IG5971 5905 PIN # 1 2 3 4 5 6 Wire Colour ORANGE WHITE RED GREEN YELLOW BLACK Description TXTX+ +12V RXRX+ GND Specifications Specifications Camera views IP-1100C - Side view camera IP-1100C PICK-UP DEVICE CMOS VIDEO COMPRESSION H.264 or H.265 NETWORK PROTOCOL MDR5,TCP/IP,HTTP,DHCP,NTP,FTP PICTURE ELEMENTS 1920*1080 IMAGE SIZE 1/2.5 EFFECTIVE HOR. RESOLUTION Approximately 800 TV Lines REQUIRED ILLUMINATION 0.05 Lux (color illumination) POWER SUPPLY 12Vdc ± 2Vdc POWER CONSUMPTION 5W (at 12Vdc) LENS ANGLE 103º(D) 84º(H) 46º(V) OPERATING TEMPERATURE RANGE -40°C ~ 70°C STORAGE TEMPERATURE RANGE -40°C ~ 85°C WEIGHT460g DIMENSIONS (W x H x D) 95.6mm x 51.2mm x 57.8mm Quick installation instructions Quick Quick installation installation instructions instructions Quick installation instructions IP-1100C IP-1X00C IP-1100C IP-1X00C www.brigade-electronics.com Quick Start Steps www.brigade-electronics.com www.brigade-electronics.com www.brigade-electronics.com www.brigade-electronics.com IP-1X00C Disclaimer Front overview camera Back door camera Quick Start Steps Note: It is recommended to choose channels 5-6 when using an MDR-504XX-XXXX and channels 9-16 when using an MDR-508XX-XXXX to avoid conflict with analogue cameras. Step 1 After connecting the IP camera with an MDR, go to the MDR On Screen Display. Right click to show the function bar and click the profile icon. Do not change Protocol Type from default settings of 'MDRS' After binding EACH camera channel click “Save”. Quick installation instructions Internet Protocol cameras have an inherent time delay and are designed to capture footage and help drivers and operators by providing high quality retrospective evidence in the event of an incident. Internet Protocol cameras should not be used as a driver aid when performing vehicle manoeuvres and do not exempt the driver from taking every normal precaution to ensure safety. No liability arising out of the use or failure of the product can in any way be attached to Brigade or to the distributor. Use Buttons “Previous CH” and “Next CH” to view and setup each IP camera Click “Exit” to exit IP camera setup page. Step 4 Click "Surveillance" -> "IPC Setup" -> "Fast Setup" Step 2 Input password. (Default is “admin”). Step 5 The MDR will start to search and connect to all IP Cameras (This will take 1-3 seconds). Part#5969/#5961/5962 #5936 Part The guide guide is is available available in: in Dutch, French, German, Italian, Polish, This xXxxxxx at Part #5969/#5961/5962 Portuguese, Russian, Spanish and Turkish at www.brigade-electronics.com/productsupportarea Part #5969/#5961/5962 Part #5969/#5961/5962 This guide is available in: xXxxxxx at www.brigade-electronics.com/productsupportarea This Thisguide guideisisavailable availablein: in:xXxxxxx xXxxxxxat at www.brigade-electronics.com/productsupportarea www.brigade-electronics.com/productsupportarea IG 5905 www.brigade-electronics.com/productsupportarea The left side of the screen will show a live view of the IP camera. The right half of the screen will show basic set up options. IPC ID: A / B; A = current showing IP camera ID Step 3 Choose “Setup” B = total IP camera/s detected Binding CH: assign the IP camera to the preferred channel. Step 6 Go back to the Live view page, the IP camera has been successfully assigned to a specific channel number. No Devise Device No Devise Device Device No Devise No Devise Device No Devise Device No Device Devise Option 2: Connecting multiple IP cameras to the MDR using 4-CH or 8-CH PON Switch Connection with multiple cameras Specifications Option 1: 1 x IP Camera connecting directly to the MDR 12V regulated DC power supply must be used to power IP Cameras (if PON Switch is not used). Alternatively, Brigade recommends the 12V DC supply output from MDR IO cable. Quick Start Connections with Steps 1 camera ** MDR-504XX-XXXX NOT COMPATIBLE WITH IP-EM-8 **
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021