IDIS DR-8416 16CH NVR 8 HDD RAID Product Manual

information on RTSP, refer to

for basic information on using the Setup menus.

Mouse

Using a mouse makes it easier to configure the settings.

A mouse lets you make selections faster and use its wheel to scroll through long menus. You can also use the mouse wheel to increase/decrease numerical values.

General

This Setup menu contains general system options.

●

Site

: Used to enter a description about the system’s installation site (no description by default). You can edit the information using the virtual keyboard.

●

System ID

: Used to identify the NVR apart from other

NVRs. System ID is also used to control the NVR with the remote control.

The default System ID is 0 and can be changed to a value between 0 and 99. The System ID can also be entered using the virtual keyboard.

●

Language

: Choose a language.

●

Version

: Indicates the software version.

●

Upgrade

: Upgrade the system. If NetFS feature is in use, click Upgrade. You can select the

USB Port

NetFS

. If the NetFS feature is not in use, you can only select the USB port. Selecting the USB port displays the USB search window. You will then be able to select an upgrade package and upgrade the system.

Selecting NetFS displays the list of registered FTP sites. Once the upgrade is completed, the NVR will reboot automatically.

When using Use 2FA feature, registered mobile device must be authenticated to upgrade the system. For more information on 2FA function, refer to

Use 2FA on page 36

Part 2 - Configuration

●

Setup

: Exports current NVR settings or imports existing settings. If the NetFS feature is in use, you can export or import NVR settings in the registered FTP site.

●

Import

: Decide whether to import network settings as well. If you do not wish to change the current network settings, do not select

Include Network

Setup

Selecting

Setup Import

does not change the settings below.

• Time-related settings (Date/Time, Time Zone, and

Use Daylight Saving Time)

• Camera-related

Advanced Settings

settings

• Camera-related

Stream

settings (Only if the resolution is different from the camera in exporting)

●

Export

: Exports the current system settings to a storage device connected to the system’s USB port or the registered FTP site in NetFS. You can designate a

File Name

for the export file.

For USB flash memory devices, the NVR supports the

FAT32 file format only.

●

Show System Log

: Displays a searchable list of 5,000 most recent system log entries. For more information on types of system log entries, refer to the

System

Log Types in the installation manual

. The icon appears next to log entries originating from a remote source. To export the system log, select the

Export

at the bottom of the screen and then designate a file name.

In order to display the system_log.txt file, you must use the correct character encoding settings and use a fixed-width font.

●

Clear All Data

: Erases all recording data. Selecting

Clear All Data

displays a confirmation window. Select

Clear

to proceed.

•

Before you perform

Clear All Data

, make sure you are not accidentally deleting important data. Erased data cannot be recovered.

•

Clear All Data

does not affect the system log.

Instead, the

Clear All Data

event will be added to the log.

●

System Shutdown

: Shuts down the system. When prompted, select

System Shutdown

●

Trubleshotting Reporting

: When there is a problem with NVR system, generate reports for troubleshooting.

Date/Time

Part 2 - Configuration

●

Holiday

: Designate holidays. On specified holidays, recording takes place according to the holiday recording schedule specified under Record Schedule.

Select the

button at the bottom of the window.

Select a date.

Select

to apply and exit.

●

Date

: Used to change the system’s date setting.

●

Time

: Used to change the system’s time setting.

●

Date Format

Time Format

: Used to change the system’s date and time formats.

●

Time Zone

: Used to designate the system’s time zone.

Refer to the map displayed on the screen and change the time zone using the mouse or the arrow buttons.

●

Use Daylight Saving Time

: Enables DST correction.

●

Time Sync.

: Select a time server for the system to synchronize with.

Select the icon to delete the existing holiday date.

Select

Automatic Sync

Enter the

Time Server

’s IP address or domain name or select and then choose a server from the list of registered time servers.

Specify the server synchronization

Interval

Select

to apply and exit.

• If you have configured the DNS Server setting under

Network - WAN

, you can enter the time server's domain name instead of its IP address.

Part 2 - Configuration

User

Use this option to register users and assign permissions.

Select the Export button to create the UPR(User

Password Reset) file. The UPR file can be used to finding a password offline. Select the location to save the UPR file and enter the file name.

Select

+ Group

and enter a group name. A group name can be up to 15 characters in length.

Specify the group’s permission settings. For more information on permission settings, refer to the

Group Permissions on page 35

Select

+ User

and then enter a user name.

If you wish to use RTSP function, set the password.

For security, It is recommended that you set a different password for RTSP and User. For more

RTSP on page 76

Select

Configure

Auto Login

and

Auto Logout

settings.

Select

Apply

to exit.

• Group names, user names, passwords and email can be entered using the virtual keyboard. For more information on using the virtual keyboard, refer to

the

Text Input via Virtual Keyboard on page 30

• To delete a registered user or group, select the icon on the right of the corresponding user/group.

Group Administrator

and User admin cannot be deleted.

• Select the icon next to Group & User on the top of the screen to delete all groups and users except

Group Administrator

and

User admin

simultaneously.

• A password entry is required to edit existing groups and users.

•

Group Administrator

's permissions cannot be changed.

• With the

User admin

account, only the password can be changed.

• When the system starts up, it will automatically log into the account designated under

Auto Login

• The system will automatically log out of the account if the duration of inactivity specified under

Auto

Logout

Select a group for the user and then enter a password. The password can be up to 16 characters in length and may include letters, symbols, and numbers. The e-mail address will be used as information on password verification.

Group Permissions

System Shutdown

Upgrade

Color Control

System Check

PTZ(Dewarping)

Control

Alarm-Out Control

Covert Camera View

Audio

Factory Reset

Search Clip Copy

May shutdown the system from the system menu.

May upgrade the system from the system menu (System

Setup).

May adjust each camera's brightness, contrast, saturation, and hue settings.

May view System

Check results.

May control PTZ and

Dewarping cameras.

May reset in the event of an alarm-out.

Alarm-outs can be reset by pressing the

Alarm

button on the device or selecting the

Alarm-Out Control

button on the remote program.

May access covert cameras in Live and

Search modes.

May use the camera audio on remote program.

May reset the NVR to all its initial factory settings.

The user who has permission for Clip

Copy can perform

Clip Copy. If the user does not have permission, Clip Copy is not allowed but only search is allowed.

Part 2 - Configuration

Setup

Camera Setup

System Time

Change

Data Clear

PTZ Setup

Alarm-Out

Setup

Covert

Camera Setup

VA Box Setup

Record Setup

DirectNDC

Setup

EventUpload

Self-

Diagnosis

Setup Import

Setup Export

May configure camera settings.

May change the system's date and time settings.

May clear data stored in the system.

May configure PTZ settings.

May configure alarmout settings.

May configure convert camera settings.

May configure VA box settings.

May configure recording settings.

May access the NVR and control it remotely via network.

May upload the video clips when an event occurs.

May configure the

NVR self-diagnostic settings.

May import previously saved NVR settings.

May export current

NVR settings.

Part 2 - Configuration

Security

Use this option to configure security settings.

When the mobile device registration is complete, the following message will appear. Click

Disable 2FA

at the bottom left corner of the screen to deactivate 2FA function via the email of an administrator user account.

Use 2FA

Two-factor authentication (2FA) is a method of confirming a user's claimed identity by utilizing a combination of two different components.

In other words, it is a method of authenticating the registered mobile devices such as mobile phones and smartphones on NVR for security when proceeding settings, search and upgrade.

When you click

Register,

the following message will appear.

To use email authentication, the SMTP setup must be configured. To use UPR funtion, the UPR file must be saved in advance.

For more information on saving the UPR file, refer to

User on page 34

• 2FA device registration is supported only via IDIS

Mobile app.

• Only the administrator account user can configure this option.

• The maximum number of device that can be registrated is 16.

Storage

Use this option to configure storage settings.

Part 2 - Configuration

RAID

●

Internal HDD

: Indicates the disks configuring RAID.

●

Setup

: Check the RAID setup information and change it Select RAID level (10,6,5,1) or Stop and then click OK to activate the selected RAID setup after the system has restarted.

●

Type

: Indicates the type of the installed disk.

●

Capacity

: Indicates the disk’s capacity.

●

Format

: If the disk has been formatted, indicates either

Record

Not Using

. If you have connected an unformatted storage device, the Use As value will be indicated as

Not Formatted

●

Information

: Indicates if the disk is being used for recording purposes. Disks that were used in different systems will show up as

Other

. Select

Information

to check the saved data’s time information or select

Delete

to erase the data.

• Select

Format

to prepare the disk as a storage for data recording.

• Disks formatted with Use As set to

Not Using

will not be used for data recording.

•

This NVR supports SATA2 HDDs.

If you change the setup related to RAID, you must reboot the system. All existing data on the disks will be erased.

●

Information

: Check the disk information configuring

RAID

HDD Installation Precautions

To reuse the HDD which was used as a RAID, low-level format the drive. Otherwise, it is recognized as a RAID error and the data of all the connected HDDs may be deleted.

Make sure to turn off the power before you add, remove or replace the HDD.

RAID Configuration Precatuions

It is possible to configure a raid represented by odd number on consecutive disk drives.

Various combinations of RAID can be configured according to the following conditions.

●

RAID 1

: Two consecutive hard drives (RAID configurations represented by disk drives 1, 3, 5 and

7).

●

RAID 5, RAID 10

: Four consecutive hard drives (RAID configurations represented by disk drives 1 and 6).

●

RAID 6

: All hard drives (RAID configuration represented by disk drive 1).

Part 2 - Configuration

RAID Configuration Error

Monitoring

Use this option to configure Monitoring settings.

●

RAID Broken

: When some of the HDDs that make up RAID are in error and then the defective HDDs are replaced, the data cannot be recovered.

●

Degrade

: If the defective HDDs are replaced, the data can be recovered by rebuilding the system. However, performance may be degraded in this case.

Degraded status

is as follows. All remaining errors are included to

RAID Broken

status.

•

RAID 1, RAID 5

: In case one of the HDDs composing

RAID is in error.

•

RAID 6

In case one or two HDDs composing RAID is in error.

•

RAID 10

: In case one or two HDDs composing RAID is in error.

(However, R10 (X,X,O,O) R10 (O,O,X,X) is included to RAID Broken status.)

–

Settings

: Configure when and what the system should monitor for.

●

Actions

: Configure alarm-out (NVR alarm-out channel, NVR beep, camera alarm-out channel) and notification (email, LAN1 through 5, SNS, push, alert window) settings.

Part 2 - Configuration

Monitoring Options

System

Bootup,

Restart,

Shutdown

Panic Record

Define monitoring times. If selfdiagnosis is not performed on a regular basis, the system will assume an error.

Define bootup, restart and shutdown actions.

Check

Recording

Define panic recording actions.

The system will assume an error if the system has been scheduled to record normally but recording does not take place during scheduled intervals.

Select

Schedule On

and then configure the days of the week, times, and monitoring interval.

Select the button on the bottom left of the screen to add a schedule. Select icon to delete the schedule.

Check Alarm-In

Disk Almost

Full

Disk Full

The system will assume an error if the alarm-in status does not change during the specified monitoring interval while alarm-in is active.

Generates an event if the disk reaches the specified capacity

(80% to 99%).

Generates an event when all disks reach their maximum capacity.

Disk Bad

Generates an event when the specified percentage of the disk becomes damaged. Set to between 10% and 90% in 10% intervals.

Disk

Temperature

Disk S.M.A.R.T.

Fan Error eSATA

Disconnected

Disk Config

Change

No Storage

Found

Consecutive

Invalid PW

Redundant

Power Error

RAID BROKEN

Degrade

Specify the threshold temperature. Once any disk reaches this threshold, the system will issue an alert.

Monitors disks that support

S.M.A.R.T. and notifies the user if a disk error is detected.

Notifies the user when the fan inside the system malfunctions.

Notifies the user if an eSATA device becomes disconnected while in use.

It will be highlighted when the

NVR reboots after the hard disk drive has been replaced.

It will be highlighted when no hard disk drive has been connected.

It will be highlighted when login fails by entering a wrong password for consecutive attempts.

It will be highlighted when the redundant power is disconnected.

(This feature is supported only with DR-8432D model)

It will be highlighted when the

RAID counfiguration is broken.

It will be highlighted when one of the HDDs composing RAID is in error.

• For system events, only an e-mail notification of actions can be selected.

• In order to use the Notify(Callback) feature, the

NVR must be registered to the remote program on the receiving PC's end.

• For more information on the RAID Broken and

Degrade,

refer to

RAID Configuration Error on page 38

Part 2 - Configuration

Self-Diagnosis

Use this option to configure self-diagnostic settings.

This feature is also supported when connected to the

NVR from a remote program.

Once

Run the failover

have made to the camera, the camera will reboot automatically.

●

Reports

–

No.

: Selects which reports to export.

–

Time

: Displays when you started the self-diagnosis.

–

View a Report

: Briefly displays whether the report is “Good” or “Bad”.

–

Click the + icon at the bottom left corner of the screen to run the self-diagnosi

–

Export

: Saves the Saves the reports to a storage device, such as the USB port and NetFS site, by converting them to HTML format. You can export more than one report at a time by selecting multiple reports.

–

Auto Generating Interval

: Select any time period between 6 hours and 7 days.

• The reports are stored in up to 24 files. If you have configured

Auto Generating Interval

as one-day period, only the the reports from the last 24 days can be viewed.

• If the NVR is turned off, the reports will automatically turn off.

• The reports are organized by recent date and time.

●

FailOver:

Whene a problem is detected on the target device, click the

Run the failover button

to resolve the problem.

–

Target Device.

: Selects which device to run the failover.

–

Channels

: Select the camera channel if a camera is set to the target device.

–

Action

: Select the type of action to run the failover.

–

Run the failover

: Click the

Run the failover

button when a fail is detected on the target device to resolve the problem.

Once you have run failover on the camera, the camera will reboot automatically. By selecting

System,

Network, Device Health Status, Storage Status,

Camera Status

VA Box Status

, you can see the brief results of the self-diagnosis for the target device.

The NVR

self-diagnostic report

can only be viewed in text form.

This feature is also supported when connected to the

NVR from a remote program.

We recommend clicking the

Export

button at the bottom of the list, which allows you to view the reports on a PC web browser. We also recommend scanning the self-diagnostic report on a remote program, which allows you to view the reports in HTML format as shown below.

About

Part 2 - Configuration

Camera Setup

Refer to the

for basic information on using the Setup menus.

Registration

You can register cameras at remote locales. By selecting a number from the list, you can move the camera up or down the list using the mouse wheel to reorder its position. The remaining cameras will move down the list automatically.

●

Title:

Edit the camera’s name.

●

MAC Address

: Displays the camera’s MAC address registered to the NVR.

●

Address

: Displays the camera’s IP address registered to the NVR.

●

Model

: Indicates the camera’s model.

●

Scan

: Select to scan and register the device connected to the NVR.

This feature is supported only when connected to the

NVR from a remote program.

Part 2 - Configuration

Device Scan

Scan the device under

Registration

Scan

●

No.

: Select the registered camera number and click the

Add Camera

button to register the camera.

●

MAC Address

: Displays the scanned camera’s MAC address.

●

Address

: Displays the scanned camera’s IP address.

●

Model

: Indicates the camera model.

●

Protocol:

Indiscates the scanned camera’s protocol.

●

Name

: Displays the scanned camera’s IP name.

●

Status

: The “Registered” indicates the camera is registered to the NVR and “Not registered” indicates the camera is not registered to the NVR.

●

Protocol

: Select the protocol you wish to search for that was used by the camera (or encoder).

• Even if the network device uses a protocol supported by the NVR, the device itself may not be visible for scanning and registration by the NVR. For more information about supported network devices and models, contact your retailer.

• The supported scan modes may vary depending on protocol selected.

●

Mode

: Select the scan mode.

–

Auto Scan(LAN)

: Lists any cameras in a LAN environment. If Auto scan (LAN) fails to recognize the camera, try using IP Address scan instead.

–

IP Address

: Enter the IP address of a camera.

The NVR scans for the camera that matches the specified address. If you enter an IP address range, the NVR scans for cameras falling under the specified address range. By specifying an IP address, you can also specify which port to use with the Remote Admin feature. It is recommended that you do not network the camera via DHCP

(Dynamic Host Configuration Protocol). If the camera is networked via DHCP, the camera may not be connected properly depending on changes in the external network environment.

If Auto Scan (LAN) fails to recognize a camera, try using the IP Address scan instead.

●

Filter

: Enter a keyword in the MAC Address / Address

/ Model / Name / Status fields for the selected camera.

This allows the user to scan this camera easily.

When configuring a port, the device may fail to scan if the port selected for the NVR and the port selected for the camera differ. In this case, you must register the camera to change its IP address.

Login

If the password is set or you want to register third party cameras, registering a device requires an authorized user login.

Select the desired deivce from the list and click the

Add Camera

button, then the login window will appear.

Select a user, enter the password, and then select

• By selecting

Apply to All Devices

, you can apply the same authentication information to all of the network devices in the list.

• When you select multiple network devices from the list and click the

Add camera

button, a window for the network device will appear.

Select

Skip

to skip the authentication settings for the current network device and to display the Authentication window of the next network device.

• For IDIS cameras, a user and password may not be required.

General

Enable/disable the covert view and rename cameras.

Part 2 - Configuration

Advanced Setup

Configure security and other advanced camera settings.

●

Title

: Edit the camera’s name.

●

Use

: Set the camera as

Normal

Covert 1

, or

Covert 2

Live images and video recordings from cameras that have been set as

Covert 1

Covert 2

will not be available to users who do not have covert camera access. Setting a camera as

Covert 1

hides its images but does display OSD information about the camera.

Setting a camera as

Covert 2

hides its images as well as ODS information about the camera as if it has been deactivated completely.

●

Use Real Time Mode

: Supports seamless video display even when there are multiple camera connections. (Only for DR-6332PS model)

• If you have configured

Use Real Time Mode

, the streaming settings may change for all registered cameras. Some settings may be disabled.

• If you have configured

Use Real Time Mode

, the remote streaming IPS can be low.

●

Video

: Adjust the camera image sensor settings such as white balance and exposure. Configuration options may differ depending on the camera model.

●

Privacy Masking

: Enable/disable and configure privacy masking for the camera.

●

SSL

: Set the camera’s security level as

Unavailable

Standard

High

, or

Very High

Standard

High

and

Very High

settings apply SSL (Secure Sockets Layer) protection to the camera.

●

Reset

: Resets the port or cameras.

–

Factory Reset

: Control the PoE Switch’s port. This option is available when connecting to Video In/

PoE port or using a DirectIP PoE Switch (optional).

Select

PoE Reset

to reboot the camera. It is not supported by video encoders.

–

Soft Reset

: Reboots the camera.

–

Factory Reset

: Resets the NVR to all its initial factory settings. It is supported by DirectIP cameras only.

●

Mode

: Select a resolution mode. This is supported by video encoders only.

●

PTZ

: If using an RS-485-compliant camera, configure it for use in PTZ Mode.

–

PTZ Product

: Choose to select the model of installed PTZ device.

–

: Choose to assign an ID to each PTZ device.

– Choose to set up

Baud Rate

Data Bit

Stop Bit

and

Parity

of the connected device.

Part 2 - Configuration

Refer to the PTZ device manufacturer’s instructions for the proper settings.

Types of configuration options shown vary depending on the PTZ functions supported by the camera.

1 2 3 4

Scan

Used to set up a profile for moving the camera between two points. At least two presets must be available in order to use the scan feature.

Set

: Used to set up a scan profile.

Numbers shown below Preset, Scan, Pattern, and

Tour indicate the numbers of configured functions.

Preset

–

Name

: Enter a name for the scan profile.

–

Start/Stop

: Specify which presets to use as start and stop points.

–

Dwell Time (sec.)

: Specify how long the camera will dwell at start and stop positions.

–

Speed/Direction

: Specify scanning speed and direction.

●

Test

: Select a scan profile and then click Test to test it.

●

Edit

: Used to edit the selected scan profile.

●

Remove

: Used to remove the selected scan profile.

Pattern

Used to set up a pattern profile for the camera to follow along.

Use the buttons below to choose a preset position.

– Directional Buttons (

Used to tilt and pan the camera.

–

Zoom

( ): Zoom in and out.

–

Focus

( ): Adjust camera focus to far or near.

–

Speed

: Specify the camera’s panning and tilting speed.

●

Set

: Choose a preset number and then enter a name.

This saves the current preset under the specified preset number and name.

●

Go to

: Select a preset from the list and then click Go to to move the camera to the selected preset position.

●

Edit

: Used to change the selected preset’s name.

●

Remove

: Used to remove the selected preset.

Start recording

: Select a pattern number, enter a name for the pattern, and then click

to save the pattern.

Move the camera using directional, zoom, and focus buttons and then click

Stop recording

to save the pattern profile. You can record up to two minutes of movement.

Part 2 - Configuration

– Directional Buttons (

Used to tilt and pan the camera.

–

Zoom

( ): Zoom in and out.

–

Focus

( ): Adjust camera focus to far or near.

–

Speed

: Specify the camera’s panning and tilting speed.

●

Test

: Select a pattern profile and then click Test to test it.

●

Edit

: Used to edit the selected pattern profile.

●

Remove

: Used to remove the selected pattern profile.

Tour

Used to set up a tour profile of multiple functions in a designated sequence.

Set

: Used to set up a tour profile.

–

Dwell Time (sec.)

: Specify how long to perform the selected function for.

–

Speed

: Specify the preset speed.

●

Test

: Select a tour profile and then click Test to test it.

●

Edit

: Used to edit the selected tour profile.

●

Remove

: Used to remove the selected tour profile.

Select

Apply

after setting up a preset, scan, pattern, or tour profile to see images from the concerned camera on the left side of the screen.

Selecting

Apply

displays a popup screen that indicates whether the profile has been set up successfully.

PTZ Reset:

Reboots the camera’s panning / tilting and zoom settings.

Home Position

: Specify the camera’s home position.

●

Default

: Uses the factory-default position as the camera’s home position.

●

Custom

: Uses the user-defined position as the home position.

●

Select

Set

to change the home position.

Auto Run

: Specify which action to take if the camera has not been controlled for the specified duration of time.

Auto Pan

: Specify the camera’s panning direction.

When Auto Pan is selected from a remote program, the camera pans in the direction selected here.

Auto Flip

: Automatically flips the image when the camera tilts past 90° to prevent the objects from appearing upside down.

●

Digital

: Flips the image left to right or top to bottom.

●

Mechanical

: Automatically pans or tilts the camera.

●

Off

: Disables Auto Flip.

Tilt-Range

: Specify the camera’s tilting range.

Restore

: Specify whether to restore the camera to its last position or function. Enabling this option restores the camera to its last position or function after being restarted.

–

Name

: Enter a name for the tour profile.

–

Function

: Indicates the order of the function in the tour sequence.

Part 2 - Configuration

Privacy Masking Options Image Sensor Options

Select

Name

to rename the privacy masking area. Select the icon to delete the existing privacy masking area.

Select

Privacy Masking Setup

to display additional privacy masking area options. You can drag on the area with the mouse to resize it or add up to 16 different areas.

●

Edit

Save

: Rename the selected privacy masking area.

Delete

: Save the changes and exit the privacy masking area options screen.

Cancel

: Delete the selected privacy masking area.

: Exit the privacy masking area options screen without saving the changes.

●

Product, Firmware Version

: Displays the camera model name and firmware version.

●

Video Style

: Select

TV1 Color

PC Color

●

Backlight Compensation

: Enable/disable Backlight

Compensation. If enabled, objects are exposed brighter in backlit situations.

●

Auto Adjust

: Selecting

Auto

allows the system to assess the lighting conditions and adjust the setting automatically. Selecting

Manual

allows the user to adjust the setting manually.

●

Sharpness

: Adjust the sharpness level. Adjust the contours to make the images look sharper. Increasing the value raises the sharpness level, but using too high a value can result in unwanted noise.

●

Noise Filter

: Select the noise filter level. Noise filter can reduce the noise in images taken under lowlighting conditions. Increasing the value reduces the noise, but using too high a value can result in blurry images.

●

3DNR

: Enable/disable 3DNR (3D Noise Removal).

3DNR reduces background noise in images taken under low-lighting conditions. 3DNR does not produce blurry images like Noise Filter but can result in ghosting.

Part 2 - Configuration

●

IR Mode

blocks out the infrared spectrum.

You can ensure clear images at all times by blocking out the infrared spectrum in high-lighting conditions and allowing the infrared spectrum to pass through in low-lighting conditions.

–

Daytime Mode/Nighttime Mode

: Enable/disable

IR Mode

–

Auto

: Allow the system to enable/disable

IR Mode

automatically.

–

Schedule

: Set up the

IR Mode

schedule.

Mode

is disabled for all days and times that are designated as

Daytime

in the schedule and is enabled at all other times.

Some camera models may not support the

Schedule

function.

●

White LED Mode

: Clicking on/off enables or disables

White LED lighting when motion is detected by the

PIR sensor. Also clicking auto allows the system to enable/disable

White LED mode

automatically.

●

Black & White Mode

: Display the images in greyscale for greater clarity in low-lighting conditions.

–

On/Off

: Enable/disable

Black & White Mode

–

Auto

: Allow the system to enable/disable

Black &

White Mode

automatically.

–

Schedule

: Set up the

Black & White Mode

schedule.

Black & White Mode

is disabled for all days and times that are designated as

Daytime

in the schedule and is enabled at all other times.

●

Pivot

: Enable this option and choose the direction of the pivot. You can turn the image by 90 degress in the clockwise or counterclockwise direction. This feature is particularly effective when monitoring hallways, passages, and other confined spaces.

The 32-channel model does not support the pivot feature.

●

Defog

: Disables or enables the Defog feature. When it is enabled, image with a fog is adjusted.

●

IR Strength

: Adjust the IR LED’s brightness level.

Select a brightness level manually between 0%

(darkest) and 100% (brightest). Selecting Auto(Smart

IR) allows the system to control the IR LEd's brigtness level automatically.

●

Smart IR

: Help solve the problem of infrared LEDs whiting out images, such as people's faces, when they are too close to the IR LEDs of a night vision camera.

In this case, the image is adjusted through AE control.

●

Advanced AE Mode

: Select desired setup mode between

Normal

and

Number-Identification

. In

Number-Identification

mode, when a certain area of images is too bright due to backlight under low lighting conditions and it causes the other area to be too dark, this function provides the other area of images brightly and clearly by blocking the backlight in the certain area. Dark parking lot entrances and gas station entrances at night, for example (Local

Exposure compensates for the bright light coming from incoming vehicle headlights and makes it possible to see the license plates). When setting to the

Number-Identification

mode, some option settings will be adjusted automatically, and you cannot change them as long as the Setup Mode is not changed.

●

Switching Level :

Controls the changing time of daytime / nighttime mode, depending on the

Switching Level between 1 to 10. The higher the value is, day / nighttime mode is changed under high-lighting conditions. Also the lower the value is, day / nighttime mode is changed under low-lighting conditions.

●

Mirror

: Select

Horizontal

Vertical

to flip the image horizontally and/or vertically.

Select

Apply

after setting up a camera to see images from the concerned camera on the left side of the screen. Selecting

Apply

displays a popup screen that indicates whether the camera has been set up successfully or not.

Part 2 - Configuration

White Balance Options Exposure Options

●

Preset

: Use preconfigured white balance settings.

–

Auto

: Allow the system to adjust the white balance automatically. The system will assess the lighting conditions and adjust the white balance automatically.

–

Incandescent - Fluorescent Cold

: Select a lighting type to apply the appropriate white balance.

●

Manual

: Adjust the white balance manually. Adjust

Red and Blue gain values. Greater the value, greater the intensity of the corresponding color.

Select

Apply

after setting up a camera to see images from the concerned camera on the left side of the screen. Selecting

Apply

displays a popup screen that indicates whether the camera has been set up successfully or not.

●

AE Target Gain

: Specify exposure compensation’s target gain. Exposure is compensated automatically based on the specified target gain. Higher the gain, brighter the images.

●

Local Exposure

: Activate Local Exposure. Use Local

Exposure on images that appear too dark due to backlighting conditions and on images containing over-exposed sections. Greater the value, clearer the image. e.g.) Dark parking lot entrances and gas station entrances at night (Local Exposure compensates for the bright light coming from incoming vehicle headlights and makes it possible to see the license plates).

●

Anti-Flicker

: If the lights in the area where the camera is located use alternating current, specify the frequency of the lights to minimize flickering.

Matching the frequencies can eliminate flickering completely. (NTSC: 60Hz, PAL: 50Hz).

●

Slow Shutter

: Activate Slow Shutter. The slow shutter mode functions only under low lighting conditions.

When the slow shutter mode is enabled, images are displayed bright even under the low-lighting conditions. There may be a difference in the way it functions depending on the camera model. See the camera user’s manual for details.

●

Focus Mode

: Used to change the focus movement format as Auto/Manual/Semi-Automatic. It may not be supported depending on the device.

●

WDR

: Disables or enables the WDR (Wide Dynamic

Range). When the very dark and very bright areas exist simultaneously on the screen, WDR allows you to recognize the both areas.

Part 2 - Configuration

●

IRIS

: Depending on the camera type, the user can select DC-IRIS or P-IRIS.

–

DC IRIS

–

OFF

: Select this if a manual IRIS lens is mounted on the camera.

–

DC-IRIS (Auto) :

Select THIS IF A DC-type auto

IRIS lens is mounted.

–

P-IRIS

–

P-IRIS (Auto)

: The system will assess the lighting conditions and adjust the openness of IRIS automatically.

–

P-IRIS (Fix) :

Use the slider to select the desired openness of IRIS. Select the most suitable value for the lighting conditions in the area where the camera is located.

●

Shutter Speed Control

: Adjust Shutter Speed. This option is available only when

Anti-Flicker

and

Slow

Shutter

are both set to

Off

–

Auto

: The system will assess the lighting conditions and adjust the shutter speed automatically.

–

Manual

: Use txhe slider to select the desired shutter speed. Select the most suitable minimum and maximum shutter speeds for the lighting conditions in the area where the camera is located.

(1/30 to 1/8000)

Select

Apply

after setting up a camera to see images from the concerned camera on the left side of the screen. Selecting

Apply

displays a popup screen that indicates whether the camera has been set up successfully or not.

View Options

●

Type

: Selects the camera view.

●

Mode

: Selects the screen layout in live mode.

• Dewarping feature is not supported when mode is set to the original.

• When changing the view mode, the resolution will be applied automatically.

Miscellaneous

●

Image Stabilizer

: Activate Image Stabilizer. The

Image Stabilizer reduces blurring caused by camera shake that results from external conditions such as the wind.

Part 2 - Configuration

Stream

Configure the camera’s live and recording resolution, codec, picture quality, transfer speed, and ips speed settings.

●

Camera Channels

: It’s possible to configure a unique video profile for each camera.

●

: Apply the video profile settings of the camera selected under Camera Channel to a different camera.

●

Live/Remote Video Profile

: Check the current Live video picture quality and edit remote video profile settings.

–

Use Dynamic Remote Stream

: Automatically transmits the

Live 1

(Single Screen),

Live 2

(2x2), or

Remote

(greater than 2x2) stream, depending on the remote program’s live screen layout.

●

Record Video Profile

: Set up 4 recording quality profiles.

●

Video Profile

: Select

Live 1

Live 2

Remote

, or

Custom

(available from Record Video Profile only).

Live 1

and

Live 2

allows the user to change

Bitrate

and

Quality

settings only and configures the remaining settings automatically.

–

Codec

: Supports H.264 and H.265.

–

Resolution

: Select a resolution supported by the camera. Maximum available resolution is chosen automatically based on the selected video profile.

–

Quality

: Select

Very High

High

Standard

Basic

, or

Manual

. You can assign different Quality settings to different cameras.

–

Bitrate

: Select

CBR

VBR

. Transmitted data size is fixed with

CBR

but varies depending on the amount of movements in the images with

VBR

–

ips

: Select a value between 1 and 30. Maximum

ips

is determined automatically based on the selected video profile.

●

Intelligent Codec

: Lower bitrate by using the intelligent codec.

• Some camera models may not support the

Intelligent Codec function.

• When using intelligent codec function, the start of some functions, such as clip copy or clip attachment can be changed to an earlier point than the selected point.

●

MAT Setup

: Select the MAP Setup option to use the

MAT (Motion Adaptive Transmission) function during video transmission and recording.

• When the MAT (Motion Adaptive Transmission) function is active, the associated VA device may not work properly.

• It is recommended that you do not use the MAT function of the associated camera to increase the accuracy of the image analysis.

• Some camera models may not support the MAT function.

* MAT function(Motion Adaptive Transmission) reduces bandwidth overload and saves storage capacity by reducing the frame rate of the video during periods of inactivity. The user can select the period of sustained inactivity which triggers this function by adjusting Inactivity Period.

●

Sensitivity

: Set the motion detection sensitivity.

Higher values will result in more sensitive motion detection.

●

Inactivity Period

: Set the Inactivity Period. If motion is not detected for the duration of time specified, video is transmitted and recorded using the frame rate designated below until movement is detected again.

Audio

Configure audio recording settings for all cameras simultaneously.

Part 2 - Configuration

SD Card

If connection between the camera and NVR fails, the video will be recorded on SD memory card of the camera. When the connection is recovered again, the recorded video on SD memory card will be recorded on the NVR. For more information on Smart Failover, refer to the the

Smart Failover on page 55.

●

Audio Codec

: Select an audio codec. (G.711 u-Law,

G.711 a-Law, ADPCM 16KHz or G.726)

●

Associated Audio In:

Associates the selected audio channel with the camera. It is supported by video encoders only.

●

Audio In

: Select an audio input source (microphone or line-in) and then adjust the volume. Noise Filter reduces the environmental noise and enhances the voice. If you turn on the noise filter, the sound may be distorted somewhat. We recommend that you do not use this function in a place with a lot of songs because it may degrade performance.

●

Audio Out

: Adjust the volume.

Cameras do not feature built-in audio amplifier units and therefore require the user to purchase a speaker system with a built-in amplifier separately.

●

Recycle

: When there is not enough storage available on SD memory card, the oldest video will be deleted automatically.

●

Format

: Click on this button to format the inserted

SD card. Formatting the SD card deletes all data saved on the card.

●

Stuatus

: Display the status of the SD card.

• This function is only supported for the cameras supporting Failover recording of SD memory card.

• For cameras is in use by other NVRs or the newly registered cameras, the Format option displays

Other

. Please format the SD card to use this function.

Part 2 - Configuration

Upgrade

When using NetFS, select Firmware Upgrade. You can select or USB port or NetFS. If not, you can only select

USB port. Selecting Camera.

Select USB port to display USB search window and then select the corresponding upgrade package from the storage device connected to the NVR’s USB port. After selecting an upgrade package, select Apply to upgrade the camera.

Record Setup

Refer to the

for basic information on using the Setup menus.

General

Configure general recording settings.

• If an upgrade attempt fails, an upgrade failure message will be displayed. Refer to

Error Code

Types in the installation manual

for more details.

• The camera will reboot after the upgrade and then reconnect automatically.

●

Recycle

: When the recording disks become full, the system overwrites existing data with new data, starting with the oldest first. If

Recycle

is disabled, recording will simply stop when the recording disks reach their maximum capacity.

●

Record Audio

: The camera will record audio along with video.

●

Event Record Dwell

: If linked recording is designated as an event-triggered action, recording takes place for the duration specified under this setting.

●

Auto Deletion

: Configure this option to delete recording data automatically after the specified number of days has elapsed. Select between 1 day and 999 days.

To disable Auto Deletion, select

Never

. If enabled, recording data will be stored on the NVR for the specified number of days and then deleted automatically. Expired recording data are deleted automatically at midnight and will be deleted even if the system reboots or the

Auto Deletion

setting has been changed.

●

VA Data Protect Duration

: Configure this option to select the data protection period. Select between 1 day and 90 days.

Part 2 - Configuration

●

Limit Time-Lapse Recording

: You can store event recording data for longer. If you do not wish to use

Limit Time-Lapse Recording

, select

Never

. This function is activated when data has been stored for longer than as configured because the recording disk has sufficient capacity and saves new data by overwriting

Time Lapse Recording

data that are older than as specified under Recycle mode.

• If the recording stored on the disk is shorter than the duration specified under

Limit Time-Lapse

Recording

, the older of

Event Recording

Time

Recording

data is deleted first.

•

The system's recording time may change depending on recording quality, resolution, motion, and other configurations made by the user. The duration specified under

Limit Time-Lapse Recording

may not be guaranteed in certain situations.

●

Use Panic Recording

: Enable/disable Panic

Recording.

●

Panic Recording Duration

: Disable Panic Recording automatically. Select between 5 mins and 1 hr. If you do not wish to disable the feature automatically, select

No Limit

●

Video Profile

: Select a recording profile value for

Panic Recording.

Schedule

<Simple Mode>

<Advanced Mode>

Disabling

Schedule On

suspends schedule recording regardless of the schedule and displays the icon on the upper left corner of each camera screen. Pressing the

Panic Record

button displays the icon and commences panic recording.

Set Record Schedule mode as

Simple Mode

Advanced Mode

allows you to configure a unique recording schedule for each event.

Select the icon to delete a schedule.

• Changing the recording schedule mode suspends all active event-linked actions.

•

Select the + button on the bottom left of the screen to add a schedule. Select

Day

to specify the

Day

setting or select

All

. Select

Scope

to specify the time frame.

Part 2 - Configuration

Simple Mode Options

●

Mode

: Select

No Record

Time

Event

, or

Time &

Event

Record

Time

Event

Unless the

Panic Record

button is pressed, no recording will take place during the scheduled time frames on the scheduled days.

The icon appears on the upper left corner of the screen. The icon appears at scheduled times to indicate recording is in progress.

The icon appears on the upper left corner of the screen. The icon appears when the specified event occurs to indicate recording is in progress.

If Pre-Event is enabled, the and

icons appear when recording is not in progress, or the and icons appear when an event occurs and recording is in progress.

Time &

Event

The icon appears on the upper left corner of the screen and recording commences as per the video profile selected for time under

Setup

. When an event occurs, the icon changes into icon and recording commences as per the video profile selected for events under

Setup

●

Channel

: Select which cameras to apply the schedule to.

●

Settings

: Select to configure default recording profile values for Time Lapse and Event Recording modes.

Advanced Mode Options

Select to configure event types and video profiles.

●

Type

: Event-specific and time recording icons are as follows:

Time Lapse

(Time)

Audio Detection

Alarm-In

Motion

Detection

Video Loss

Trip Zone

Tampering

Text-In

Recording Fail

Face Detection

Exceed the

People Limit

ANPR

Fan Error

Exceed the Time

Limit

VA Loss

●

Video Profile

: Configure the profile to use for recording.

●

Dwell

: Specify how long to record for after a corresponding event occurs.

• Upper-tier schedule's settings apply to unconfigured channels.

• If multiple events take place on a specific channel and different

Video Profile

and

Dwell Time

settings apply, highest settings apply to all event-linked recordings.

Pre-Event

When an event occurs, enabling this option includes the specified duration prior to the event in the eventtriggered recording.

Part 2 - Configuration

Smart Failover

When the connection is recovered again, Smart Failover

Service enables the data recorded on SD memory card to record on NVR.

●

No.

: Select which cameras to apply Pre-Event to.

●

Video Profile

: Select a video profile for the recording.

●

Dwell

: Specify the duration of pre-event recording data.

• If no event mode schedule exists in the schedule, a warning message prompting you to add an event mode schedule will be displayed.

•

The warning message will appear even in

Time &

Event

mode.

●

Recorded Data

: Indicates the time information of the recorded data.

●

Video Profile

: Select a video profile for the smart failover recording.

●

Status

: Indicates the current status of the recorded data.

• This function supports only if selecting the

Recording Failover Serivce

•

This function is only supported for the cameras supporting Failover recording of SD memory card.

•

If the camera is reconnected during recording, the video recording will restart from the beginning.

Part 2 - Configuration

Event Setup

information on using the Setup menus.

Use the remote control’s arrow buttons to move the block selection window up, down, left, and right. The selection window consists of 8 blocks per row. Select/ deselect individual blocks using the

Camera

buttons.

You can use the mouse to drag the zone and then select, clear, or reverse the selection.

From the zone selection screen, press the button on the remote control or right-click on the mouse to open up the Zone Setup menu.

Video-Analytics

Video-Analytics methods are Motion, Trip Zone, and

Tampering.

Motion

●

No.

: Select which cameras to apply Motion Detection to.

●

Sensitivity

: Set daytime and nighttime sensitivity settings between 1 (Low) and 5 (High).

–

Select

: Confirm the block selection in the selection window.

–

Clear

: Clear the block selection in the selection window.

–

Reverse

: Clear the blocks selected within the selection window and select all unselected blocks within the selection window.

–

Select All

: Select all blocks.rmn

–

Clear All

: Clear all block selections.

–

Reverse All

: Clear all selected blocks within the screen and select all unselected blocks within the screen.

–

: Save the changes and exit the menu.

–

Cancel

: Exit the menu without saving the changes.

●

Zone

: Define the motion detection block.

●

Min. Blocks

: Motion needs to be detected in more than the specified number of blocks in order to trigger a Motion Detection event. You may select a value between 1 and the number of blocks selected under

Zone

for daytime and nighttime, each.

●

Etc

: Select Etc to detect an event on PTZ movement.

Part 2 - Configuration

●

Ignoring Interval

: The system does not produce event log entries or issue remote notifications regarding motion detected for the time specified after the initial motion was detected. Set the value between 1 sec and 5 secs or choose

Never

Ignoring Interval does not affect motion detection recording.

●

Daytime Setup

: Specify when daytime starts and ends. Adjust the time frame in 15-minute increments.

Times outside the specified range will be assumed as nighttime by the system.

●

Actions

: Specify which actions to take when motion is detected.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Part 2 - Configuration

Trip Zone

●

No.

: Select which cameras to apply Trip Zone to.

●

Sensitivity

: Set daytime and nighttime sensitivity settings between 1 (Low) and 5 (High).

Zone

: Define the motion detection block.

Use the remote control’s arrow buttons to move the block selection window up, down, left, and right. The selection window consists of 8 blocks per row. Select/ deselect individual blocks using the

Camera

buttons.

You can use the mouse to drag the zone and then select, clear, or reverse the selection.

From the zone selection screen, press the button on the remote control or right-click on the mouse to open up the Zone Setup menu.

–

Select

: Confirm the block selection in the selection window.

–

Clear

: Clear the block selection in the selection window.

–

Reverse

: Clear the blocks selected within the selection window and select all unselected blocks within the selection window.

–

Select All

: Select all blocks.

–

Clear All

: Clear all block selections.

–

Reverse All

: Clear all selected blocks within the screen and select all unselected blocks within the screen.

–

Trip Direction

: Define in which direction the motion has to occur in order for it to be considered an event. Select In for movements from outside the selection area in or Out for movements from inside the selection area out.

–

: Save the changes and exit the menu.

–

Cancel

: Exit the menu without saving the changes.

Part 2 - Configuration

●

Actions

: Specify which actions to take when Trip Zone is detected.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

●

Trip Zone Ignoring Interval

: The system does not produce event log entries or issues remote notifications regarding Trip Zone events detected during the specified time following the initial Trip

Zone event. Set a value between 1 sec and 5 secs or choose Never.

Trip Zone Ignoring Time does not affect Trip Zone recording.

●

Daytime Setup

: Specify when daytime starts and ends. Adjust the time frame in 15-minute increments.

Times outside the specified range will be assumed as nighttime by the system.

Tampering

●

No.

: Select which cameras to apply Tampering to.

●

Sensitivity

: Set to between 1 (Low) and 5 (High).

●

Activation Time

: Specify how long tampering detection needs to last in order for it to be considered an event. Tampering detections that do not last for the specified duration of time will not be considered as events.

●

Actions

: Specify which actions to take when

Tampering is detected.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to

Event

Time & Event

mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

●

Use Ignoring Time

: Select

Time Setup

to specify the tampering detection ignore time. Tampering detection will be disabled during the specified time frame.

Part 2 - Configuration

Alarm-In Video Loss

●

No.

: Enable / disable alarm-ins.

This option includes both local and network camera alarm-ins. 1 through 32 are network camera alarm-ins, whereas 33 through 48 are local alarm-ins.

●

Title

: Use the virtual keyboard to enter titles.

●

Type

: Change the alarm-in type.

●

Actions

: Specify which actions to take when Alarm-In is detected.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

•

Select

Panic Record

to specify which alarm-in channels to use. Panic Record commences when the corresponding alarm-in occurs and terminates when the alarm-in is deactivated.

●

Activation Time

: Specify how long video loss has to last in order for it to be considered as an event.

When the video loss is not detected for the specified duration of time, it will not be considered as an event.

●

Actions

: Specify which actions to take when a Video

Loss event occurs.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to

Event

Time & Event

mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

●

Ignoring Interval

: The system does not produce event log entries or issue remote notifications for video loss detected for the time specified after the initial video loss was detected. Set the value between

0.1 and 15 seconds or choose

Never

. This is supported only when video encoders are connected.

●

Use Ignoring Time

: Select

Time Setup

to specify the time to ignore video loss detection. Video loss detection will be disabled for a specified time period.

This is supported only when video encoders are connected.

Audio Detection

●

Activation Time

: Specify how long audio detection has to last in order for it to be considered as an event.

When the audio detection is not detected for the specified duration of time, it will not be considered as an event.

●

No.

: Select which cameras to apply Audio Detection to.

●

Sensitivity

: Set to between 1 (Low) and 5 (High).

●

Activation Time

: Specify how long audio detection has to last in order for it to be considered an event.

Audio detections that do not last for the specified duration of time will not be considered as events.

●

Actions

: Specify which actions to take when audio detection events occur.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Part 2 - Configuration

●

Ignoring Interval

: The system does not produce event log entries or issues remote notifications regarding audio detected during the specified time following the initial audio detection. Set a value between 1 sec and 5 secs or choose

Never

●

Use Ignoring Time

: Select

Time Setup

to specify the audio detection ignore time. Audio detection will be disabled during the specified time frame.

Part 2 - Configuration

Recording Fail Text-In

●

Activation Time

: Specify how long recording fail has to last in order for it to be considered as an event. When the recording fail is not detected for the specified duration of time, it will not be considered as an event.

●

Actions

: Specify which actions to take when a

Recording Fail event occurs.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to

Event

Time & Event

mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

●

Setup

: Configure text-in devices.

• It's possible to batch configure all text-in devices with the exception for port settings.

• An influx of large amounts of text-in data from multiple channels can hinder system performance.

●

Text-In Product

: The setup window is updated so that the portion below the port setting matches the corresponding text-in device. Displayed screenshot illustrates Generic Text settings.

●

Transaction Start

: Once

Transaction Start

has been designated, the system will recognize the specified string as the beginning of a transaction. You can choose the Any Character setting. Under this setting, any character will trigger the system into recognizing the start of a new transaction.

●

Transaction End

: Once

Transaction End

has been designated, the system will recognize the specified string as the end of a transaction. Select

0 more line(s)

next to Transaction End and specify a value between 1 and 10. The system will recognize the specified Transaction End string plus the number of lines as being the end of a transaction.

Part 2 - Configuration

●

Line Delimiter

: Designate a string to mark the end of a line. You can enter control strings by selecting and then entering ^, followed by a letter. For example,

Carriage Return is ^M and Line Feed (new line) is ^J.

●

Ignore String

: Specify a string to ignore from transaction records.

●

Case Sensitive

: Ignores case in strings designated under

Transaction Start

Transaction End

Line

Delimiter

, and

Ignore String

Case Sensitive

does not apply to control strings.

●

Time Out

: Once

Time Out

has been enabled, the system will assume the end of a transaction if no new string is entered within the specified duration of time.

Select between 5 secs and 15 mins.

Selecting RS-232, RS-485, USB-Serial 1 through 8, or LAN

1 through 16 as the port activates the Port Setup button.

Select

Setup

and configure the

Baud Rate

Data Bit

Stop Bit

, and

Parity

settings.

• If any one of LAN1 through 16 has been selected as the port, select the Port Setup button and configure the network port setting.

• If using a USB-serial port, the Text-In feature may malfunction if the USB cable is removed while the system is in operation.

●

Title

: Designate a name for the text-in device.

●

Actions

: Specify which actions to take when text-in is detected.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify

: Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

ANPR

●

Setup:

Configurea ANPR devices.

●

Port

: If any one of the LANs has been selected as the port, select the Port Setup button and configure the network port setting.

●

ANPR Product

: Configure the product to apply ANPR function.

●

Actions

: Specify which actions to take when ANPR event occurs.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify:

Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Part 2 - Configuration

Camera System

The event occurs when the fan has stopped in the fan mounted camera.

Face Detection

When face detection event occurs in the selected camera, the area that the face is detected displays on the screen.

●

No.:

Select which cameras to apply Fan Error to.

●

Actions:

Specify which actions to take when a Fan

Error event occurs.

–

Record:

Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out:

Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify:

Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ:

Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

• In case of the camera that not supports camera system event, the camera system feature will be disabled.

●

No.:

Select which cameras to apply Face Detection to.

●

Sensitivity

: Set sensitivity settings between 1 (Low) and 5 (High).

●

Max

. Detect Count: Set the maximum detected number of face as 8 or 32.

When you set the Max. Detect Count as 32, the sensitivity feature will be disabled.

●

Min. Face Size:

Select 120 x 120, 150 x 150, 180 x180,

210 x 210 or 240 x 240.

●

Actions:

Specify which actions to take when a Face

Detection event occurs.

–

Record:

Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out:

Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify:

Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ:

Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

• In case of the camera that not supports face detection event, the face detection feature will be disabled.

●

Ignoring Interval:

The system does not produce event log entries or issue remote notifications regarding face detected for the time specified after the initial motion was detected. Set the value between 1 sec and 5 secs or choose Never.

Queue Management

Part 2 - Configuration

●

Setup

: Configure Exceed the Time and People Limit event.

–

Exceed the People Limit

: When the number of selected people in a defined area (zone) exceeds the limit, an event occurs.

–

Exceed the Time Limit

: When people stay in a defined area longer than the time set, an event occurs.

●

Actions:

Specify which actions to take when an event occurs.

–

Record:

Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to Event or Time & Event mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out:

Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify:

Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ:

Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

• In order to use the Callback feature, the NVR must be registered on the remote program.

• In order to use the Queue Management feature, it should be set on the channel.

Part 2 - Configuration

VA Loss

Device Setup

Refer to the

for basic information on using the Setup menus.

Alarm-Out

●

Activation Time

: Specify how long VA loss has to last in order for it to be considered as an event. When the

VA loss is not detected for the specified duration of time, it will not be considered as an event.

●

Actions

: Specify which actions to take when a VA loss event occurs.

–

Record

: Specify which cameras to begin linked recording on when an event occurs. If the schedule is set to

Event

Time & Event

mode, the selected cameras will begin linked recording when an event occurs.

–

Alarm-Out

: Designate event-triggered alarm-out channels (each for the NVR and camera) and beeps.

–

Notify:

Configure to be notified of events by Mail,

LAN1 through 5, Push, FTP, and/or Alert Window.

–

PTZ

: Moves the PTZ camera to a specific preset position when an event occurs.

–

Event Monitoring:

Selects the cameras to monitor when an event occurs.

In order to use the Callback feature, the NVR must be registered on the remote program.

Click the + icon at the bottom left corner of the screen to add a schedule.

You can apply different schedules for different

Day

s of the week.

Select icon to delete the schedule.

●

Dwell Time

: Select a value between 5 secs and 15 mins as the alarm-out duration.

●

Title

: Designate a name for the alarm-out.

●

Range

: Change the schedule time frame.

●

Mode

: Select

Event

, or

Off

Event

Generates an alarm-out when an event occurs.

Alarm-out is always on.

Off

Alarm-out is always off.

●

Channels

: Configure alarm-out port and beep settings.

Remote Control

Part 2 - Configuration

VA Box

By analyzing camera images, you can check real-time analysis results from a client program such as the IDIS

Center.

●

Port

: Select

None

RS232

RS485.

Click the

Setup

button and then select the correct

Baud Rate

Parity

Data Bits

and

Stop Bits

for the device you are connecting to the NVR. You can select the device from the

Remote Control Product

list. If the

RS232

port and RS485 port are in use for PTZ control, networking or text input, the remote keyboard cannot be configured. A warning message window will appear when other devices are using the same port, such as

PTZ control, networking or text input. The message warns that you cannot use another device because the ports overlap.

VA Box can only analyze the video from the camera using H.264 and H.265.

VA BOX_Registration

You can register VA Box at remote locales.

●

Title:

Edit the VA Box’s name.

●

MAC Address

: Displays the VA Box’s MAC address registered to the NVR.

●

Address

: Displays the VA Box’s IP address registered to the NVR.

●

Model

: Indicates the VA Box’s model.

●

Scan

: Select to scan and register the device connected to the NVR.

Part 2 - Configuration

Device Scan

Scan the device under

Registration

Scan

People Counting

Count the number of people passing through the line on the live screen.

●

No.

: Select the registered VA Box number and click the

Add Box

button to register the camera.

●

MAC Address

: Displays the scanned device’s MAC address.

●

Address

: Displays the scanned device's IP address.

●

Model

: Indicates the device model.

●

Registered Device MAC Address

: Displays the MAC address of the NVR to have registered VA Box.

●

Status

: The “Registered” indicates the VA Box is registered to the NVR and “Not registered” indicates the VA Box is not registered to the NVR.

Right-click on the zone setup screen to bring up the

People Counting Menu.

–

Crossing Line

: Set a virtual border to count the floating population.

–

Head:

Set the size of a head on the screen based on the floating population.

A miscount may occur when a head is set too large or too small.

–

Freeze :

You can pause or resume the live screen by pressing it.

–

Save :

Save the changes and exit the menu.

–

Cancel :

Exit the setup screen without saving the changes.

VA BOX_Setup

Configure VA Box-related settings.

HeatMap

Analyze the movement frequency in the zone of the live screen. Use the left mouse button to define the zone.

Drag and drop the vertex to modify a previously set zone and click on the left mouse button to reset the zone.

●

Title

: Displays the name of a VA Box.

●

Camera

: Select the camera to analyze the video. Only one camera can be set for each VA Box channel.

The video analytics may not be supported depending on the model.

●

Analytic Type

: Select one among People Counting,

HeatMap and Queue Management. A single video analysis function is available for each VA Box channel.

Lines cannot cross when setting the zone.

Right-click on the zone setup screen to bring up the the

HeatMap Menu.

–

Undo :

Return to the previously set zone.

Part 2 - Configuration

–

Save:

Save the changes and exit the menu.

–

Cancel :

Exit the setup screen without saving the changes.

Queue Management

Count and manage time and the number of people who have stayed in the set zone. Use the left mouse button to define the zone. Drag and drop the vertex to modify a previously set zone and click on the left mouse button to reset the zone. You can create a maximum of five zones.

●

Configuration

: Configure the details of the VA Box.

Select the VA Box’s

Analytic Type

first before you use this setup.

Lines cannot cross when setting the zone.

●

Overhead Type

: Set the size of a head on the screen to detect only the person.

Right-click on the zone setup screen to bring up the

Queue Management Menu.

–

Head

: Set the head size of the person.

–

Freeze :

You can pause or resume the live screen by pressing it.

–

Delete

: Delete the zone selected in the image.

–

Undo :

Return to the previously set zone.

–

Edit name:

Set the name of the zone.

–

Save :

Save the changes and exit the menu.

–

Cancel :

Exit the setup screen without saving the changes.

–

Dynamic Background Suppression :

Recognize the objects (people) even if the background is moving.

–

Light Disturbance :

Recognize the objects in the lighting conditions such as sunlight.

–

Shadow Suppression :

Set not to recognize the shadow as an object.

–

FishEye :

When the camera is tilted, recognize the lower and upper body together, not separately.

–

Object Tracking:

The object tracking slider sets the sensitivity. The closer the level is to the

Sensitive

, the more sensitively the device can track the movement.

●

Filter Area Setup

–

Dynamic Background Filter :

Do not detect the new object in the dynamic background filter area.

When an already detected object moves into the area, it can track the movement.

–

Non-Tracking Filter :

Do not detect the new object in the non-tracking filter area. When an already detected object moves into the area, the track will be released.

Filter Area Setup function is only supported if the

Analytic Type

is set to People Counting or Queue

Management.

–

Cooldown :

Indicate on the screen the HeatMap information recorded before

Cooldown

–

Record Duration :

Set the recording interval to save the HeatMap data.

Cooldown and Recording function are only supported if the

Analytic Type

is set to HeatMap.

Part 2 - Configuration

–

Detection Reference Time (sec.) :

Set the time to detect objects in the queue management zone. It detects when the objects (people) stay longer than the time frame set in the defined area.

Detection Reference Time (sec.) is only supported if the

Analytic Type

is set to Queue Management.

●

Reset:

Resets the port or VA Box.

–

PoE Reset:

Control the PoE Switch’s port. This option is available when connecting to Video In/

PoE port or using a DirectIP PoE Switch (optional).

Select PoE Reset to reboot VA Box.

–

Soft Reset:

Reboots VA Box.

Use a client program such as IDIS Center to check the analysis results.

VA BOX_Upgrade

When using NetFS, select Firmware Upgrade. You can select USB storage or NetFS. If not using NetFS, you can select USB storage only. Select USB storage to display

USB search window and then select the corresponding upgrade package from the storage device connected to the NVR’s USB port. After selecting an upgrade package, select Apply to upgrade the VA Box.

VA BOX_Schedule

Configure the schedule of the VA Box. Select the

+ button on the bottom left of the screen to add a schedule. Select Day to specify the Day setting or select

All. Select Scope to specify the time frame.

• If an upgrade attempt fails, an upgrade failure message will be displayed. Refer to

Error Code

Types in the installation manual

for more details.

• The VA Box will reboot after the upgrade and then reconnect automatically.

Deleting the schedules stops the real-time video analysis.

Network Setup

information on using the Setup menus.

General

●

Remote Audio Channel

: Transmits the selected channel’s audio to the remote program. Select

Select

From Client

to stream audio of the channel selected on the remote program.

Audio skipping and sync issues can occur under poor network conditions.

●

Enable SSL for Transferring Data

: Applies SSL

(Secure Sockets Layer) protection on remote viewing and recording data transmissions.

• If using the SSL feature, it will not be possible to connect to the NVR from a remote program or a network keyboard that does not support SSL.

• Changing the SSL setting temporarily severs all remote connections to the NVR in order to apply the change.

• This product contains content developed by

OpenSSL Project for use in Open SSL Toolkit (http:// www.openssl.org/).

●

IDIS Web

: If you wish to use IDIS Web, select

IDIS Web

- Use IDIS Web Service

. Select IDIS Web - IDIS Web

Port and choose a port number between 1024 and

65535. The port number can also be entered using the virtual keyboard. For more information on IDIS Web,

refer to the

Part 4 - IDIS Web on page 96

Part 2 - Configuration

●

DirectNDC

: Use Direct Network Display Control (NDC) by clicking the

Use DirectNDC

button to toggle between On and Off. You will be able to change the settings if Use DirectNDC is enabled. DirectNDC service allows you to access the NVR and control it remotely using a PC or mobile devices via Ethernet.

–

Port

: Configure the port number of the DirectNDC server.

–

Password

: Configure the

Password

to connect to the NVR from a remote locale.

Up to three users at a time can access a NVR remotely via DirectNDC service.

●

Network Bandwidth Limit

: Configure the bandwidth limit.

If you configured

Network Bandwidth Limit

, the live video may not display smoothly in a remote program.

Part 2 - Configuration

Key

←

→

↑

↓

Enter or

Return

Character

Input,

Delete,

BackSpace,

Space

Esc

Function

Press the

←

to move to the left in the menu. This is the same as pressing the

Left arrow button on the front panel or the remote control.

Press the

→

to move to the right in the menu. This is the same as pressing the

Right arrow buttons on the front panel or the remote control.

Press the

↑ to move up in the menu.

This is the same as pressing the Up arrow button on the front panel or the remote control.

Press the

↓ to move down in the menu.

This is the same as pressing the Down arrow button on the front panel or the remote control.

Press the Enter or Return key to select the highlighted item or complete an entry that you have made during system setup. This is the same as pressing the Play/Pause button on the front panel or the remote control.

They play the same role as a keyboard input.

Press the Esc to escape the sequence .

Press the F1 key to perform the panic recording . This is the same as pressing the PANIC button on the front panel or the remote control.

Press the F2 key to reset all NVR outputs while the alarm has been activated including the built-in buzzer.

This is the same as pressing the

ALARM button on the front panel or the remote control.

Press the F3 key to initiate PTZ mode.

This is the same as pressing the PTZ button on the front panel or the remote control.

F4 or

PaceUP/

PageDown

F10 or

Windows

Home

Press the F4 or PageUp or PageDown key to toggle between different display formats. This is the same as pressing the LAYOUT button on the front panel or the remote control.

Press the F5 key to refresh the current

DirectNDC screen.

Press the F6 key to switch to the search mode. This is the same as pressing the Search Mode Button on the front panel or the CALENDER button the remote control.

Press the F10 or Windows key to display the Live Monitoring menu or

Search menu on the screen. This is the same as pressing the

MENU

button on the front panel or the remote control.

Press the Home key to copy video clips. This is the same as pressing the

CLIP COPY button on the front panel.

WAN

Designate the IP address type as

Manual

DHCP

Manual

Part 2 - Configuration

●

Ping Test

: Select to test the current WAN settings you made.

● Set

Type

to Manual.

Manual

lets you configure related settings manually.

Configure

IP Address

Gateway

, and

Subnet Mask

settings manually using the remote control's arrow buttons or the virtual keyboard.

●

DNS Server

: Enter the DNS server’s IP address. The

IP address can also be entered using the virtual keyboard.

●

Remote Port

: The port used by the remote program to connect to the NVR. Choose a value between 1024 and 65535. The port number can also be entered using the virtual keyboard.

Enter the IP address of the NVR.

Adjust the frequency of the ping test.

Select

Run

to do the test. The test result is displayed.

Select

Close

to exit.

• If using a firewall, select Change Port to change the port number to one that is permitted by the firewall.

•

Changing the port temporarily severs the NVR's remote connection.

Remote point IP and port settings on the remote program must also be changed in order for it to connect to the NVR.

●

To use the

UPnP

(Universal Plug and Play) feature, select

Use UPnP

. If using an IP router (or NAT), UPnP service allows the device to automatically forward the port to the NVR.

• This port is used to access a port that has a private

IP address.

• In order to use the UPnP service, the IP router (or

NAT) must support UPnP port forwarding and have the relevant options enabled.

• Port number cannot be changed with

Use UPnP

selected.

●

Status

: Indicates the number of the port forwarded by the IP router (or NAT) to the NVR via UPnP service.

Part 2 - Configuration

DHCP

FEN

If using a dynamic IP address, FEN service makes it easy to connect to the NVR from a remote program without having to configure dynamic IP or router settings.

Select

DHCP

and then

Save

to retrieve IP address and other network settings automatically from the DHCP server. Once the network settings have been retrieved, the NVR’s current IP address is displayed in the IP

Address field.

• It may not be possible to retrieve the IP address if there is no DHCP server. If this is the case, contact your network administrator.

• With DHCP, the NVR's IP address might change with each startup.

There is a limit to the number of users allowed to connect remotely at the same time. Contact the service center for more information.

●

Use FEN

: Check if you wish to use FEN service.

●

FEN Name

: After entering the NVR name you wish to register on the FEN server, check and register the entered name. This is a unique NVR name that will be registered on the FEN server.

•

You will not be able to save FEN settings unless you click on the Check button next to the NVR Name field and check the entered name's availability.

•

You will be prompted with an error message if you do not enter NVR name or enter a name already registered to the FEN Server.

• If the device name contains the #, \, and/or % symbol, it might not be able to connect to the NVR from the IDIS Web program.

●

FEN Server

: Enter the FEN server’s IP address or domain name.

If you have configured the DNS Server setting under

Network - WAN

, you can enter the FEN server's domain name instead of its IP address in the

FEN

Server

field.

●

Port

: Specify the FEN server’s port number.

If using an IP router (or NAT), port configuration and other network functions will depend on the usage method of the IP router (or NAT).

●

Status

: Used to check the status of the device being registered to the FEN server.

Select

Save

after making changes to register the NVR’s name to the FEN server.

If FEN has been configured correctly, the FEN server's help desk information will be displayed in the

Help

Desk

field the next time you access the FEN Setup screen.

Part 2 - Configuration

NetFS

This allows you to register NetFS sites for the following functions:

●

Upload or download files to upgrade, import/export of a setup file, log export, self-diagnosis export, or file print on an FTP site. The related settings are as follows:

: (Setup) in the live monitoring mode - System menu - General tab - Upgrade, Import, Export or

SystemLog - Self-Diagnosis Export

: (Setup) in the live monitoring mode - System menu - Self-Diagnosis Export

: in the search mode - (Print)

●

Upload clip-copy files to an FTP site. The related settings are as follows:

: (Export) in the search mode - A-B Clip-Copy or

Clip-Copy.

●

FTP notification of an event detection (system events excluded). The related settings are as follows:

: (Setup) in the live monitoring mode - Notification menu - FTP tab - FTP setting,

: (Setup) in the live monitoring mode - Event menu - Actions – Notify (FTP) setting)

•

It is recommended that you use FileZilla and smallFtp servers.

• This feature is supported only in the passive mode

(PASV) of the FTP site.

●

Use

: Select the usage for the NetFS feature.

– N/A : Disables the NetFS feature.

– ALL: Enables the NetFS feature.

– Upgrade: Allows you to use the upgrade file that was uploaded to the NetFS site.

– Setup: Allows you to import or export a setup file that was uploaded to the NetFS site.

– System Log – Allows you to save system logs to the

NetFS site.

– Clip-Copy – Allows you to manually copy video clips or automatically copy event-detected video clips to the NetFS site.

– Print – Allows you to save images as a PDF file to the NetFS site.

●

Site

: Enter NetFS site information.

• When you delete an FTP site from the NetFS setup screen in the Network menu, the FTP site in the FTP setup screen in notification will be deleted, too.

• When you change the usage to anything other than

ALL or Clip-Copy, the FTP notification function will be disabled.

• Select the icon to delete the existing NetFS site.

Enter information about the NetFS site using the virtual keyboard and then click the

test

buton to test the current NetFS site.

Select Use NetFS to use the

NETFS feature

. Click the + icon at the bottom of the list to add up to 16 FTP sites.

●

Title

: Check if you wish to use FEN service.

●

Title

: Enter the NetFS site name using the virtual keyboard.

●

Address

: Enter the NetFS address using the virtual keyboard.

●

Port

: Configure the port to connect to the NetFS site.

●

Remoth path

: Enter a folder path to the NetFS site using the virtual keyboard.

●

User

Password

: Enter the user and password to access the NetFS site using the virtual keyboard.

●

Test

: Test the current NetFS site settings you have entered.

Part 2 - Configuration

RTSP

RTSP service allows you to monitor real-time using the

Real-Time Streaming Protocol.

Firewall

Setting up a customized firewall rule set, it allows or denies access such as specific MAC address, IP address and receiving network port of the NVR.

●

RTSP Port

: Set the port number of the RTSP server obtained from your system administrator.

●

RTP Port

: Set the start/end port number of the RTP server obtained from your system administrator.

• You can access a remote NVR and monitor live video images using media players, such as VLC Player, supporting RTSP service. Start the media player on your local PC and enter

“rtsp://ID:Password@IP address:RTSP port number/trackID=channel number” (e.g.: rtsp:// admin:@10.0.152.35:554/trackID=1)

• Video display on certain media players may not be smooth depending on the network status.

• RTSP service might not be supported, depending on the type of media player.

Select

Use Firewall

to activate firewall function. Click the + icon at the bottom of the list to set up a firewall rule.

●

Title:

Edit the name of the rule.

●

Type:

Set the IP adddress, the MAC address or the network port.

●

Action:

Select which actions to apply this firewall rule to.

–

Drop:

Discard the packet that matches all the specified conditions.

–

Reject:

Deny the packet that matches all the specified conditions and send back an ACK packet telling it that the "packet was dropped" to the sender.

–

Accept:

Allow the packet that matches all the specified conditions.

●

Interface:

Specify the ethernet interface. It refers to a

WAN (Network Client) or VIN (Video-In).

●

Mac Address:

If the rule is set to MAC address, enter the sending MAC address

●

IP:

If the type of the rule is set to IPv4 or within the

IPv4 scope, enter the sending IP address.

●

Port:

If the type of the rule is set to port or within the port scope, enter the receiving network port number of NVR.

Part 2 - Configuration

NAT

Notification Setup

NAT function is to connect to the camera which is internal VIN network from the physically divided WAN network PC (WebSetup / IDIS Web / IDIS Center program

/ RTSP).

To connect to the camera WebSetup / IDIS Web / IDIS

Center program / RTSP function, you need to configure the NAT rule to forward ports from NVR port number to the camera port number.

Schedule

Select the + icon at the lower left corner of the screen to add a notification schedule.

Select

Use NAT

to activate NAT function. Click the + icon at the bottom of the list to set up a NAT rule.

●

Day

: Add different schedules for different days of the week.

●

Range

: Change the event notification time frame.

●

Notify

: Select which notifications to generate when an event occurs. Select

Mail

LAN 1 through 5

Push

FTP

, and/or

Summary

•

In order to use the

Notification

(Callback) feature, the NVR must be registered on the remote program.

• Select the icon to delete the existing schedule.

●

Summary Email Interval

: Transmit event summary emails to a remote destination at specified intervals.

●

Title:

Edit the name of the rule.

●

Type:

Set the IP adddress, the MAC address or the network port.

●

Action:

Select which actions to apply this NAT rule to.

–

PORT_FORWARD:

Allow the access by combining an external TCP/UDP port with an internal port.

●

Protocol:

Set the network protocol to apply the rule to.

●

Interface:

Specify the ethernet interface. It refers to a

WAN (Network Client) or VIN (Video-In).

●

IP:

If the type of the rule is set to IPv4 or within the

IPv4 scope, enter the sending IP address.

●

Port:

If the type of the rule is set to port or within the port scope, enter the receiving network port number of NVR.

It is not possible to set an interface from VIN to WAN direction. For more information on NAT, refer to

NAT

Configuration Guide on page 103

Part 2 - Configuration

Callback

Configure Callback settings.

●

+Mail

: Add a mail recipient

Select the group name and then assign the

Group

Recipient. Enter the the recipient's e-mail address and mail server provider. Select the icon to select the mail server provider from a list ot registered SMTP mail server providers.

Enter the IP address of the receiving server and set

Retry

to between 1 and 10 in case of connection failure.

Mail

Configure Mail settings.

The recipient's mail address must be in the correct email format and contain the @ symbol.

Select the

Attach Type

to attach event recordings to outgoing mails to an account that belongs to that group.

Select the icon to remove the account and added group.

●

+Group

: Add a recipient group and select the image file format attached to an email.

A virtual keyboard appears allowing you to enter the

Group name. You can select between CBF and MP4.

When selecting CBF, the NVR will attach an event detected video clip to an email. When selecting MP4, the NVR will attach the event detected image file (MP4 format) to an email.

Part 2 - Configuration

SMTP Setup

Select

SMTP Setup

at the bottom right corner of the screen to configure an SMTP server.

Select the SMTP server

Type

Enter the

SMTP Server

’s IP address or domain name and then configure the

Port

and

Sender

settings.

Push

Configure Push settings.

Default SMTP server port number is

. Select

Test

to send out a test mail using the current settings.

Select SS/TLS or STARTTLS, depending a method of supporting a secure connection.

• If you have configured the DNS Server setting under

Network - WAN

, you can enter the STMP server's domain name instead of its IP address in the

SMTP

Server

field.

• Address entered under

Sender

must be in the correct email format and include the @ symbol.

If user authentication is required by the SMTP server, select

Use

and then enter the

User

and

Password

information.

Select

Push

to use Push feature.

The Push feature sends out event-related messages to mobile phone.

Enable to receive the event occured in NVR on the mobile phone(Android, iOS). The NVR must be registered and set in mobile phone.

Select

to apply and exit.

This product contains content developed by OpenSSL

Project for use in Open SSL Toolkit (http://www.

openssl.org/).

Part 2 - Configuration

FTP

The FTP feature uploads event-detected images or video clips to the FTP site when an event occurs. Click the + icon at the bottom of the list to add an FTP site.

●

FTP

: Enter the FTP site information using the virtual keyboard.

●

Upload File

: Select the file format to be uploaded to the FTP site.

Up to 5 FTP sites can be registered.

Click the + icon at the bottom of the list to add an FTP site.

• For the FTP notification to work properly, the related settings should be configured as follows:

Network menu - NetFS tab - Use setting

Event menu - Actions - FTP setting

• When you delete an FTP site from the NetFS setup screen in the Network menu, the FTP site in the

FTP setup screen in the Notification menu will be deleted, too.

• If many event occurs during a short period, the images may not be uploaded to the FTP site.

• The FTP notification is not supported for system events.

• If upload fails several times, the images or video clips are deleted.

• When the NVR boots, all images and video clips are deleted even if they were not uploaded yet.

●

Site

: Displays the list of the registered FTP sites.

Select an FTP site from the list. If the Use settings of the NetFS site are set to anything other than

ALL

Clip-Copy

, you cannot select the FTP site. You can change the Use settings or register other FTP sites in the NetFS setup screen in the Network menu.

●

Upload File

: Select between

CBF

and

MP4

. When you select

CBF

, the NVR will upload an event detected video clip to the FTP site. When you select

MP4

, the

NVR will attach an event-detected video clip to the

FTP site.

●

Site Information

: Displays information for the FTP site.

Display Setup

information on using the Setup menus.

Main Monitor

Configure monitor-related settings.

Part 2 - Configuration

OSD

Show OSD (On Screen Display) information on the bottom of the screen.

Status

●

Date

and

Time

: Displays the date and time.

Camera

●

No.

: Displays the camera number on the upper left corner of the camera screen.

●

Title

: Displays the camera name on the upper left corner of the camera screen.

●

Record

: Displays recording and schedule icons.

●

Audio

: Displays the icon on channels generating audio.tkfkd60

●

PTZ

: Displays the icon on PTZ cameras.

●

PTZ Zoom

: Displays the zoom magnification (e.g. x2, x3, etc.)

●

Text-In / ANPR

: Displays data received from text-in and ANPR devices. Select

Display Dwell

and specify how long to display data. Data are shown on the single screen only.

●

Resolution (Search)

: Displays the recording resolution in Placyback mode.

●

Codec (Search)

: Displays the codec information in

Placyback mode.

●

Mode

: Select

Full Sequence

Cameo Sequence

●

Interval

: Select between 3 secs and 2 mins. For more information on Sequence, refer to the

8 Sequence on page 23

●

Manual Configuration

: Set the resolution manually regardless of the resolution supported by the monitor.

●

Resolution

: Select from 3840 x 2160, 1920 x 1200,

1920 x 1080, 1680 x 1050 and 1600 x 1200.

●

Event Monitoring On

: With Event Monitoring enabled, the camera screen linking event monitoring is shown. For more information on Event Monitoring, refer to the

Event Monitoring on page 26

●

Event Alert

: With Event Alert selected, the red line appears on the top of the camera screen linking event monitoring when an event occurs.

• Supported resolutions may be restricted depending on the monitor.

• 3840 x 2160 @ 50/60Hz resolution is supported only in HDMI 2.0 monitor.

• We recommend using 3840 x 2160 or 1920 x 1080 resolution.

• If you use a VGA monitor as the main display, we recommend that you use a resolution of 1920 x

1080 or below.

• HDMI deep color feature is not supported.

●

Use BRP(Boost Remote Performance) mode

: With

BRP mode on, the camera full screen does not display in live mode and the network bandwidth can limit to

100Mbps.

Part 2 - Configuration

Status Setup