Advertisement
Advertisement
Network
Camera
Operation Manual
DC-E4513WRX
Powered by
2
Before reading this manual
This is a basic operation manual for use of an IDIS network camera. Users who are using this product for the first time, as well as users with experience using comparable products, must read this operation manual carefully before use and heed to the warnings and precautions contained herein while using the product. Safety warnings and precautions contained in this operation manual are intended to promote proper use of the product and thereby prevent accidents and property damage and must be followed at all times. Once you have read this operation manual, keep it at an easily accessible location for future reference.
• The manufacturer will not be held responsible for any product damage resulting from the use of unauthorized parts and accessories or from the user’s failure to comply with the instructions contained in this manual.
• The information in this document is believed to be accurate as of the date of publication even though explanation about some functions may not be incorporated. The manufacturer is not responsible for any problems resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
• It is recommended that first-time users of this network camera and individuals who are not familiar with its use seek technical assistance from their retailer regarding product installation and use.
• If you need to disassemble the product for functionality expansion or repair purposes, you must contact your retailer and seek professional assistance.
• Both retailers and users should be aware that this product has been certified as being electromagnetically compatible for commercial use. If you have sold or purchased this product unintentionally, please replace with a consumer version.
Safety Symbols
Symbol Publication
IEC60417, No.5031
Direct current
Description
In-Text
Symbol Type Description
Caution
Important information concerning a specific function.
Note
Useful information concerning a specific function.
Before reading this manual
Safety Precautions
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING
: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
Important Safeguards
1. Read Instructions
All the safety and operating instructions should be read before the appliance is operated.
2. Retain Instructions
The safety and operating instructions should be retained for future reference.
3. Cleaning
Unplug this equipment from the wall outlet before cleaning it. Do not use liquid aerosol cleaners. Use a damp soft cloth for cleaning.
4. Attachments
Never add any attachments and/or equipment without the approval of the manufacturer as such additions may result in the risk of fire, electric shock or other personal injury.
5. Water and/or Moisture
Do not use this equipment near water or in contact with water.
6. Placing and Accessories
Do not place this equipment on an wall or ceiling that is not strong enough to sustain the camera. The equipment may fall, causing serious injury to a child or adult, and serious damage to the equipment. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.
This equipment and cart combination should be moved with care.
Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.
Do not place this equipment in an enclosed space. Sufficient ventilation is required to prevent an increase in ambient temperature which can cause malfunction or the risk of fire.
7. Power Sources
This equipment should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power, please consult your equipment dealer or local power company.
You may want to install a UPS (Uninterruptible Power Supply) system for safe operation in order to prevent damage caused by an unexpected power stoppage. Any questions concerning UPS, consult your UPS retailer.
This equipment should be remain readily operable.
8. Power Cord
Operator or installer must remove power and TNT connections before handling the equipment.
9. Lightning
For added protection for this equipment during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the equipment due to lightning and power-line surges. If thunder or lightning is common where the equipment is installed, use a surge protection device.
10. Overloading
Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.
11. Objects and Liquids
Never push objects of any kind through openings of this equipment as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the equipment.
12. Servicing
Do not attempt to service this equipment yourself. Refer all servicing to qualified service personnel.
13. Damage requiring Service
Unplug this equipment from the wall outlet and refer servicing to qualified service personnel under the following conditions:
A. When the power-supply cord or the plug has been damaged.
B. If liquid is spilled, or objects have hit the equipment.
C. If the equipment has been exposed to rain or water.
D. If the equipment does not operate normally by following the operating instructions, adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the equipment to its normal operation.
E. If the equipment has been dropped, or the cabinet damaged.
F. When the equipment exhibits a distinct change in performance — this indicates a need for service.
14. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
15. Safety Check
Upon completion of any service or repairs to this equipment, ask the service technician to perform safety checks to determine that the equipment is in proper operating condition.
16. Field Installation
This installation should be made by a qualified service person and should conform to all local codes.
17.Tmra
A manufacturer’s maximum recommended ambient temperature
(Tmra) for the equipment must be specified so that the customer and installer may determine a suitable maximum operating environment for the equipment.
3
Before reading this manual
FCC Compliance Statement
THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART
15 OF THE FCC RULES. THESE LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL INTERFERENCE
WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE
RADIO FREQUENCY ENERGY AND IF NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCE TO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A RESIDENTIAL AREA IS LIKELY TO
CAUSE HARMFUL INTERFERENCE, IN WHICH CASE USERS WILL BE REQUIRED TO CORRECT THE INTERFERENCE AT THEIR OWN EXPENSE.
WARNING
: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE COULD VOID
THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. THIS CLASS OF DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE
CANADIAN INTERFERENCE CAUSING EQUIPMENT REGULATIONS.
WEEE (Waste Electrical & Electronic Equipment)
Correct Disposal of This Product
(Applicable in the European Union and other European countries with separate collection systems)
This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling.
Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
Copyright
© 2019 IDIS Co., Ltd.
IDIS Co., Ltd. reserves all rights concerning this manual.
Use or duplication of this manual in part or whole without the prior consent of IDIS Co., Ltd. is strictly prohibited.
Contents of this manual are subject to change without prior notice for reasons such as functionality enhancements.
Registered Trademarks
IDIS is a registered trademark of IDIS Co., Ltd.
Other company and product names are registered trademarks of their respective owners.
4
This product contains software built partially on open-source content. Codes for the corresponding open-source content are available for download depending on whether or not the source is publicly available under a license policy. For more information, refer to
System > General
page. This product includes software developed by the
University of California, Berkeley and its contributors, and software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.oepnssl.org/). Also, this product includes cryptographic software written by Eric
Young ([email protected]).
Table of Contents
1
5
6
Table of Contents
2
3
Part 1 - Remote Setup
Configure basic network camera settings and all other system settings.
Screen images may vary depending on the model.
Remote Setup
1
Launch the IDIS Discovery program and then from the main screen, select a network camera whose settings you wish to change.
2
Click on the
Setup
icon.
3
Select
Remote Setup
from the
Setup
menu to load the
Remote Setup
screen. Alternatively, you can select
Network Camera
from the main screen and then right-click to access the
Remote Setup
screen.
• System settings can also be changed using a remote program.
• Remote Setup works with the following web browsers when the web browsers support HTML5:
Microsoft Internet Explorer version 10 or later,
Google Chrome, Mozilla Firefox, or Apple Safari.
It may not work properly with Microsoft Internet
Explorer version 9.0 or earlier. It is recommended that you update the web browser to the latest version. When you launch
Remote Setup
on a
Microsoft Internet Explorer version 10 or later supporting HTML5 and the
Remote Setup
screen does not appear, check if the web browser’s document mode is set to
9
or higher or
Edge
. You can check the document mode as follows: Press the
F12
key on the keyboard
→
click the
Document mode
icon.
7
8
Part 1 - Remote Setup
Quick Setup
From the Remote Setup screen, select the menu on the left to display the current settings.
Select an option under the menu to change the corresponding settings. Once you have changed the settings, click
Save
to apply the settings.
Quick Setup allows you to set up
System
,
Network
,
Video
,
Audio
, and other basic settings needed for camera use.
System
Change the camera’s system information, add users/ groups, and/or import/export settings.
General
•
Language
: Select the language you wish to use for remote setup.
•
Name
: Enter a name for the camera. (Up to 31 alphanumeric characters, including spaces)
•
Note
: Enter a description for the camera.
•
HW Version/SW Version
: Indicates the camera’s hardware and software versions.
•
Miscellaneous
-
ONVIF Protocol
: Select to enable ONVIF protocol use. However, ONVIF Protocol is available only to users belonging to the standard user groups
(
Administrator
,
Operator
, and
User
) and when video compression is set to H.264 or JPEG under
Video > Streaming
menu. When you have connected to the camera by using the ONVIF protocol, only the currently enabled streams or events are supported and you cannot change it.
There may be some more settings that cannot be changed, too. If you want to change those settings, connect to the camera by using the IDIS Discovery program.
-
ONVIF Event Type
•
Normal:
This is the usual way the camera delivers events.
•
Standard:
This is the ONVIF standard event delivery method.
-
Opensource Licenses:
Click
View
to see the information of opensource licenses.
Part 1 - Remote Setup
•
Setup
-
Load Default Setup
: Restores all settings other than Date/Time to their factory defaults. Select
Include Network Setup to load default network settings as well. For more information on network
.
-
Import Setup
: Open a setup file and apply its settings to the camera. Click on the button and then select a setup file. Select Include Network
Setup to apply the file’s network setup settings (exc.
FEN). For more information on network setup, refer to the
.
-
Export Setup
: Export the current settings as a .dat file. Click on the button and then enter a file name.
•
Load Default Setup
and
Import Setup
options are available only to users belonging to the
Administrator
group.
• When applying the settings of a setup file, do not select the
Include Network Setup
option if the network settings contained in the selected file is currently being used by a different camera. Doing so can interfere with establishing a connection with the other camera.
• If IP Address, Port, and/or SSL settings have been changed, click
Save
to apply the current settings, and then restart Remote Setup. If you do not restart Remote Setup, the changes afterwards will not be applied.
9
Part 1 - Remote Setup
Date/Time User/Group
•
Date/Time
: Change the camera’s date/time settings and display formats and configure the time zone and daylight saving time settings. Click
Save
to apply the changes right away.
•
Time Sync
-
Automatic Sync
: Select to synchronize the system’s time with the time server at a specified interval.
Enter the time server’s IP address or domain name and then specify the interval. If the time server is
FEN
-enabled, select the
Use FEN
option and then enter the time server’s name instead of its IP address or domain name.
-
Run as Server
: Select to run the camera as a time server. Other devices will then be able to synchronize its time setting with this camera’s time setting.
If you wish to enter a domain name instead of an
IP address for the
Time Server
setting, DNS server
setup. If you wish to enter a server name instead of an IP address or a domain name, the
Use FEN
option must be
setup.
•
User/Group
: Change remote camera control permission settings for users and user groups.
-
Add Group
: Add a new user group. Designate a name for the group and then specify control authorities.
-
Add User
: Add a new user. Designate a name for the user, select which group to add the user to, and then enter a connection password.
-
Edit
: Edit group authorities and/or user passwords.
Select a group or user and then click on the button.
-
Remove
: Delete groups or users. Select a group of user you wish to delete and then click on the button.
•
Allow Anonymous Login
: Select if you are using
Webcasting. For more information on webcasting,
10
Part 1 - Remote Setup
.
•
User/Group
settings can only be configured by users belonging to the
Administrator
group.
• There is no default password for the
Administrator
group's
admin
user.
• Standard groups (
Administrator
,
Operator
, and
User
) cannot be edited or deleted. Authorities assigned here apply identically to ONVIF protocol user groups.
• Group authorities that can be assigned are as follows:
–
Upgrade
: Upgrade the system.
–
Setup
: Configure the system's settings.
–
Color Control
: Adjust the camera's brightness, contrast, saturation, and hue settings.
–
Alarm-Out Control
: Reset alarm outs.
–
Search
: Search video recordings saved on the SD memory card from a remote program.
–
Clip-Copy
: Search video recordings saved on the
SD memory card and save them as video files from a remote program.
Network
Change the network settings, enable FEN and security features, and control network bandwidth use.
IP Address
IPv4
11
Part 1 - Remote Setup
•
Type
: Select the type of network you are using. If this option has been changed, click
Save
to apply the current settings, and then restart Remote Setup. If you do not restart Remote Setup, the changes afterwards will not be applied.
-
Manual
: Select if using a static IP. You will then be able to configure the related settings manually.
-
DHCP
: Select if connected to the network using
DHCP. Click
Save
to retrieve IP address and other network settings automatically from the DHCP server.
•
DNS Server
: Enter the DNS server’s IP address. By using the DNS server, you will be able to use domain names instead of IP addresses when configuring the
FEN, time, or SMTP server. If the camera is connected to the network via DHCP, select the
From DHCP
option to retrieve the DNS server’s IP address from the
DHCP server automatically. The updated address will be displayed upon the subsequent connection.
IPv6
• Check
Use
to activate IPv6.
•
Type
: Select the type of network you are using. If this option has been changed, click
Save
to apply the current settings, and then restart Remote Setup. If you do not restart Remote Setup, the changes afterwards will not be applied.
-
Manual
: Select if using a static IP. You will then be able to configure the related settings manually.
-
DHCP
: Select if connected to the network using
DHCP. Click
Save
to retrieve IP address and other network settings automatically from the DHCP server or the router. If it can not be received automatically, it will be created automatically from the camera.
•
View IP Address Information:
The IPv6 address assigned to the IP camera is shown.
•
DNS Server
: Enter the DNS server’s IP address. If the camera is connected to the network via DHCP, select the
From DHCP
option to retrieve the DNS server’s IP address from the DHCP server or the router automatically. If it can not be received automatically, it will be created automatically from the camera.
The updated address will be displayed upon the subsequent connection.
• Contact your network administrator for more information on the camera's network connection type, the DNS server's IP address, and other related information.
• If using DHCP, the camera's IP address may change from time to time. We therefore recommend that you use the
FEN
feature.
• If using IPv6, some network function may be limited.
12
FEN
Select
Use FEN
to enable the
FEN
feature.
•
FEN Server
: Enter the FEN Server’s IP address or domain name.
•
Port
: Enter the FEN Server’s port number.
•
FEN Name
: Enter a camera name you wish to register to the FEN Server. Click
OK
to check the name’s availability.
Part 1 - Remote Setup
•
Use FEN
is a feature that allows you to register a unique name for a camera that utilizes a dynamic
IP address to the FEN Server and connect to the camera using the registered name instead of an
IP address, which can change from time to time.
Moreover, you can access the camera without having to configure NAT (Network Address
Translation) device settings even when the camera uses a NAT device. In order to use this feature, you must first register a FEN name to the FEN Server.
• If network settings have been changed, click
Save
at the bottom of the setup window to save the changes and then setup the
FEN
.
• Inquire with your network administrator for the
FEN
Server
’s IP address or domain name. If a DNS server has been configured under
Network
setup, you can enter the FEN Server’s domain name instead of its IP address for the FEN Server setting.
•
FEN Server
's default address is
fen.idisglobal.
com
. DNS server must be configured under network setup to ensure normal operation.
• You will not be able to save
FEN
settings unless you click on the
OK
button next to the
FEN name
field and check the entered name's availability.
In addition, you will be prompted with an error message if you do not enter a FEN name or enter a name already registered to the FEN Server.
If the FEN name contains special characters, the connection may not be made when the WebGuard or remote setting is accessed by FEN name through the Web browser. (If you can not access special characters, you can access by changing the encoding.)
The FEN Server operated by IDIS is a service to its clients and may go offline without notice for server update purposes or due to an unexpected failure.
13
Part 1 - Remote Setup
Port/QoS
•
Use HTTPS
: Select this option to apply https protocolbased security on IDIS Web.
•
Use UPnP
: If the camera is connected to the network via an IP router (or NAT), select this option to connect to the camera without setting up port forwarding.
The IP router (or NAT) must be enabled with UPnP in order for this feature to function properly. For more information enabling UPnP on your IP router (or NAT), refer to the
IP router or NAT’s operation manual
.
Click
Check
to test the current port settings.
A confirmation message will appear if all the selected ports are available for use. If not, a list of recommended port numbers will be shown.
•
Use/Port
: Enable/disable ports and designate corresponding port numbers.
Remote Port
and
IDIS
Web / HTTP
ports are enabled by default and cannot be disabled. By enabling IDIS Web and RTSP ports, you will be able to use the IDIS Web program or a media player that supports RTSP (Real-Time Streaming
Protocol) service to connect to the camera. When the HTTP port is enabled, you can run the camera’s
Remote Setup. If this option has been changed, click
Save
to apply the current settings, and then restart
Remote Setup. If you do not restart Remote Setup, the changes afterwards will not be applied.
•
DSCP
: Designate each port’s QoS (Quality of Service) level using DSCP values. Assigning QoS levels prioritizes the ports for network bandwidth use.
Higher the DSCP value, higher the QoS level and thus higher on the network bandwidth allocation priority list. Use
0
if you do not want to assign a QoS level. The network environment must support DSCP in order for this feature to function properly. Contact your network administrator for more details.
Click
Apply
to use the recommended port numbers.
•
Use SNMP
: Select this option to enable SNMP (Simple
Network Management Protocol).
14
Bandwidth Control
Regulates the camera’s network bandwidth use based on network traffic fluctuations.
Part 1 - Remote Setup
• In a WAN environment, it is recommended that you use the UPnP function if you record video by using the FEN function or FEN connection is not smooth.
Otherwise, monitoring or recording might not be smooth depending on the network environment.
• Each port number must be unique.
• It is not allowed to use the same port number for more than one function.
• You can connect to the camera using a media player that supports RTSP service and monitor its video feed. If the camera is connected to the network via an IP router (or NAT) or is behind a firewall, you must open the ports. (All ports if using UDP protocol and
RTSP ports if using TCP protocol) This feature may not be supported by al media player. In addition, video display on certain media players may not be smooth depending on the network status, video streaming compression method used, and/or the resolution setting. Connection methods are as follows:
–
Via PC
: Launch the media player (such as VLC) and then enter
rtsp://ID:Password@IP Address:
RTSP Port Number/trackID='Stream Number'
(Stream Number: 1 if Primary, 2 if Secondary, and
3 if Tertiary). (e.g.: rtsp://admin:@10.0.152.35:554/ trackID=1 (User: admin, Password: None, Camera
IP Address: 10.0.152.35, RTSP Port Number: 554,
Stream: Primary))
• Port numbers of the remote program must be updated whenever the camera's port numbers are changed.
• ONVIF protocol may not function if using HTTPS.
Select
Network Bandwidth limit
and then specify the maximum bandwidth. The camera will not be able to use more than the specified limit in the event of network traffic.
It may not be possible to produce the frame rate specified under
Video > Streaming
if a network bandwidth limit has been set.
15
Part 1 - Remote Setup
Security
•
IP Filtering
: Select this option to enable IP Filtering.
IP Filtering allows camera access from certain IP addresses and blocks access from others.
-
Add
: Add new IP addresses to Allow List or Deny
List. Select the
Host
option to add one IP address at a time. Select the
Group
option to define a range of
IP addresses you wish to add.
-
Remove/Remove All
: Remove individual or all IP addresses from Allow List or Deny List.
•
SSL
: Select this option to enable SSL (Secure Sockets
Layer). Enabling this option applies SSL protocol protection on data transmitted out. However, programs and systems that do not support SSL will not be able to connect to the camera. If this option has been changed, click
Save
to apply the current settings, and then restart Remote Setup. If you do not restart Remote Setup, the changes afterwards will not be applied.
• Time server, FEN Server, and SMTP server's IP addresses must be added to Allow List under
IP
Filtering
in order to use Time Sync, FEN, and Send
Email features. No connection to the camera will be permitted whatsoever from IP addresses added to
Deny List
.
• Enabling the
SSL
option may place a greater load on the external system, depending on the level of security being used.
• This product contains software developed by Open
SSL Project for use in Open SSL Toolkit. (http://www.
openssl.org/)
16
IEEE 802.1X
Select the
IEEE 802.1X
option to enable IEEE 802.1X network connection authentication.
Video
Part 1 - Remote Setup
•
Certificates
: Upload a certificate or a private key. You may be prompted to enter a password for the private key.
•
Settings
: Configure EAP (Extensible Authentication
Protocol) settings.
-
EAP Type
: Choose a network connection authentication method. Selected method must be identical to the authentication method used on the authentication server.
-
EAPOL Version
: Choose EAP authentication’s version.
-
EAP Identity/EAP Password
: Enter authentication
ID and password.
The authentication server and AP must support IEEE
802.1X authentication in order for the IEEE 802.1X network connection authentication feature to function properly.
Configure
Camera
,
Streaming
,
Webcasting
,
MAT
, and
Privacy Masking
options.
17
Part 1 - Remote Setup
Camera
Image Sensor
Configure
Image Sensor
settings.
White Balance
Configure
White Balance
settings.
•
Mode:
Choose resolution.
16:9 for 4M and 4:3 for 5M.
When changing sensor mode, some settings will be reset to default.
•
Mirroring
: Select Horizontal Reverse or Vertical
Reverse to flip the image horizontally or vertically.
•
Pivot
: Select a direction to rotate images 90 degrees clockwise or counterclockwise. If vertical resolution is less than 320, this function is not supported. If you enable this function, you can monitor more efficiently long and narrow space such as hallways, corridors, etc. If both Mirroring and Pivot functions are enabled,
Mirroring functions first, then Pivot.
•
Defog:
Disables or enables the Defog feature. When it is enabled, image with a fog is adjusted.
•
Preset
: Use preconfigured white balance settings.
-
Auto
: Allow the system to adjust the white balance automatically. The system will assess the lighting conditions and adjust the white balance automatically.
-
Hold:
Hold the current white balance.
-
INCANDESCENT - FLUORESCENT COLD
: Select a lighting type to apply the appropriate white balance.
If the
Preset
is
Hold
and the WDR mode is changed, a reset is required.
•
Manual
: Adjust the white balance manually. Adjust
Red and Blue gain values. Greater the value, greater the intensity of the corresponding color.
If the white balance does not work properly under the following specific conditions, select
Manual
or
Hold.
- When the surrounding environment of the object is out of the color temperature correction range
- When the surrounding environment of the object is dark
- The camera is pointed directly at the fluorescent lamp or installed in a place where the lighting change is severe.
18
Exposure
Configure
Exposure
settings.
•
AE Target Gain
: Specify exposure compensation’s target gain. Exposure is compensated automatically based on the specified target gain. Higher the gain, brighter the images.
•
Anti-Flicker
: If the lights in the area where the camera is located use alternating current, specify the frequency of the lights to minimize flickering.
Matching the frequencies can reduce flickering.
(NTSC: 60Hz, PAL: 50Hz) When using WDR, flickering can be present in poor environments even if Anti-
Flicker is turned on.
•
Slow Shutter
: Activate
Slow Shutter
. The electronic shutter’s speed will decrease to the specified level under low-lighting conditions to allow more light in and therefore produce brighter images.
•
WDR:
Disables or enables the WDR(Wide Dynamic
Range). When the very dark and very bright areas exist simultaneously on the screen, WDR allows you to recognize the both areas.
•
Backlight Compensation
: Enable/disable the
Backlight Compensation feature. If using WDR,
Backlight Compensation OFF does not work.
-
ON
: When images are too bright overall due to backlight, objects are exposed brighter under backlight circumstances.
•
Exposure Control:
Adjust Shutter Speed and gain.
This option is available only when
Anti-Flicker
and
Part 1 - Remote Setup
Slow Shutter
are both set to
Off
.
-
Auto:
The system will assess the lighting conditions and adjust the shutter speed and gain automatically.
-
Manual:
Use the slider to select the desired shutter speed and gain. Select the most suitable minimum and maximum shutter speeds and gains for the lighting conditions in the area where the camera is located.
With certain features, selecting
Auto
automatically loads settings suitable for the camera's installation environment.
19
Part 1 - Remote Setup
Day & Night
Configure
Day & Night
settings.
•
B&W Mode
: Display the images in greyscale for greater clarity in low-lighting conditions.
-
On/Off
: Enable/disable B&W Mode.
-
Auto
: Allow the system to enable/disable B&W
Mode automatically.
-
Schedule
: Set up a B&W Mode schedule. B&W
Mode is enabled on days and times designated as
Nighttime
and disabled at all other times. Select
On
or
Off
at the bottom of the schedule table and then click or drag on the dates and times to select/ unselect as
Nighttime
. Select
On
or
Off
and then click
Select All/Clear All
to select/unselect all dates and times as Nighttime.
•
IR Cut Filter
: IR Cut Filter blocks out the infrared spectrum. You can ensure clear images at all times by blocking out the infrared spectrum in high-lighting conditions and allowing the infrared spectrum to pass through in low-lighting conditions.
-
Nighttime Mode
/
Daytime Mode
: Disables or enables the IR cut filter.
-
Auto
: Allow the system to enable/disable IR Cut
Filter automatically.
-
Schedule
: Sets up the IR cut filter schedule. The
IR cut filter is disabled during the date and time scheduled as
Nighttime
and enabled during the rest. Set up or release Nighttime by selecting
On
or
Off
in the bottom and clicking or dragging the date and time area in the table. Selecting On or Off and clicking the
Select All/Clear All
button sets up or releases Nighttime for all dates and time.
•
Switching Mode:
Change the switching mode of daytime and nighttime. In normal mode, daytime/ nighttime is switched through the amount of light received by the ambient light sensor. In advanced mode, it is switched through the amount of light and the analysis of the camera video.
•
Switching Level:
Sets up the switching level between daytime and nighttime modes. For example, if the darkness level is set to
3
and the brightness level to
5
, the system switches to nighttime mode when in lighting conditions of level 3 or below and to daytime mode when in lighting conditions of level 5 or over. It is recommended that you do not set up the darkness level and brightness level identically; otherwise, this function may not work properly. This functions only when
B&W Mode
or
IR Cut Filter
is set to
Auto
.
20
Miscellaneous
Configure
Miscellaneous
settings.
Streaming
Part 1 - Remote Setup
•
IR Strength:
Set the brightness of the IR LED. The higher the value is set, the brighter it is.
•
Smart IR:
Prevent the object from being saturated by
IR light. Select
On
to always control saturation and select
Auto
to control saturation only when the zone is over-saturated.
•
Image Stabilizer:
Disables or enables the image stabilizer function. When the image stabilizer is enabled, it reduces blurring caused by camera shake that results from external conditions such as the wind.
Image Stabilizer
may not work properly in the following situations:
• When there are many moving objects on the screen
• Monotonous environment with few objects
• Noise is generated due to lack of light
•
Primary/Secondary/Tertiary/Quaternary
:
Multistreaming is supported. Enable/disable streaming use.
The stream you set first has priority.
21
Part 1 - Remote Setup
•
Compression
: Choose the streaming compression method. The H.265 compression does not support
ONVIF Protocol and RTSP.
When using H.265 compression, a device that does not support H.265 compression may prevent the screen from being displayed.
•
Resolution
: Choose a resolution setting for video streaming. The resolution varies depending on the camera model. The current stream resolution cannot be higher than the higher stream resolution.
•
Quality
: Choose a quality setting for video streaming.
•
Target Bitrate(Kbps):
Set the target bitrate. When
Quality
is set to
Manual
, you can configure the value of the target bitrate. If not, the set value of the target bitrate for each
Quality
appears.
•
Bitrate Control
: Choose a bitrate control mode for video compression.
-
CBR (Fixed Bitrate):
Maintains the current bitrate regardless of motion change in the video.
-
VBR (Variable Bitrate)
: Bitrate varies depending on motion changes in the video. Less movement places less load on the network and takes up less storage space.
•
Frame Rate
: Choose a frame rate setting for video streaming. The fame rate of the current stream cannot be higher than the fame rate of the higher stream if those stream resolutions are same.
•
Default Record Stream
: Choose a stream to use for recording. This setting, however, may not apply if a recording stream has been designated from the remote program or the SD memory card recording feature has been enabled.
•
Intelligent Codec:
Analyze real-time video intelligently to minimize bitrate while maintaining frame rate and image quality.
•
Multi-View Streaming
: Designate a specific area of the screen and stream images from that area only.
(not supported for the primary stream) Click
Setup
to designate a streaming area.
Select
On
and then specify the streaming area’s resolution.
22
-
Resolution Limit
: Indicates the maximum resolution that can be set for the streaming area.
-
Resolution
: Designate a streaming area.
Designated area is marked in red on the screen. You can adjust the resolution of the area or reposition the area by dragging and dropping using the mouse.
-
Current Resolution
: Displays the resolution of the designated streaming area.
• If multiple users are connected to the camera, the increase in bandwidth use can lower the frame rate.
Part 1 - Remote Setup
Webcasting
Use the webcasting service to view live images from the camera on a web site.
•
HTML Code
: Copy and paste the html code shown on the screen within the code of the web page you want the video to be displayed.
•
Stream
: Choose a stream to use for webcasting. Only a stream currently in use can be selected.
In order to use the webcasting service, the
Allow
Anonymous Login
option under
System > User/
Group
must be selected.
23
Part 1 - Remote Setup
MAT
Select the
MAT
option to use the MAT (Motion Adaptive
Transmission) feature during video transmission and recording.
•
Frame Rate
: Designate the frame rate to be used between the end of the Inactivity Period and the next motion detection. When the slow shutter mode is enabled under
Video > Camera
menu, the fame rate may change. Video is transmitted and recorded at the designated frame rate between then end of the
Inactivity Period and the next motion detection. Once motion is detected again, the frame rate designated under
Streaming
is restored immediately.
MAT (Motion Adaptive Transmission)
is a feature that lowers the frame rate when motion is not detected to reduce the load on the network and save on storage space. Based on the specified sensitivity setting, no movement will be assumed if there is no change between two consecutive images.
•
Sensitivity
: Set the motion detection sensitivity.
Higher values will result in more sensitive motion detection.
•
Inactivity Period
: Set the Inactivity Period. If motion is not detected for the duration of time specified, video is transmitted and recorded using the frame rate designated below until movement is detected again.
24
Privacy Masking
Select
Privacy Masking
to set up a privacy mask over a specific area. The section on which a privacy mask is applied will appear as black when monitoring video.
Audio
Configure audio in/out settings.
Part 1 - Remote Setup
•
Privacy Masking Setup
: Set up privacy masks(up to
8).
-
(Select)/ (Unselect)
: Set or remove a privacy mask. Click on the button and drag & drop using the mouse to set up a privacy mask.
-
No./Name
: Displays a list of active privacy masks.
The numbers indicate privacy mask numbers. Select the empty space next to a number to assign a name to the corresponding privacy mask. Click
Delete
to remove the selected privacy mask.
25
Part 1 - Remote Setup
In/Out
Event Action
Designate event detection alert actions.
•
Audio Codec
: Select an audio codec.
•
Input
: Select an option and then adjust the volume.
Noise Filter
reduces the environmental noise and enhances the voice. If you turn on the noise filter, the sound may be distorted somewhat. We recommend that you do not use this function in a place with a lot of songs because it may degrade performance.
•
Output
: Select an option and then adjust the volume.
Cameras do not feature built-in audio amplifier units and therefore require the user to purchase a speaker system with a built-in amplifier separately.
26
Alarm out
Select
Alarm Out
to enable alarm out.
Select
to send out emails.
Part 1 - Remote Setup
•
Dwell Time
: Designate the alarm out duration. When an event occurs, alarm out will be generated for the specified duration.
•
Schedule
: Specify the alarm out schedule. Alarm out is generated during the specified period only.
•
SMTP Server/Port
: Enter the SMTP server’s IP address
(or domain name) and port number you received from the network administrator. If a DNS server has been set up during network configuration, you can enter a domain name instead of an IP address.
•
Use SSL/STARTTLS
: If using an SMTP server requiring an SSL or STARTTLS connection, select
SSL
or
STARTTLS
option.
•
Authentication
: Enter a user ID and password if user authentication is required by the SMTP server.
•
Sender/Recipient(s)
: Enter the sender and recipients’ addresses. (Up to 10) The addresses must be properly formatted and include the @ symbol.
27
Part 1 - Remote Setup
Remote Callback
Select
Remote Callback
to send callback messages to a remote system.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
Audio Alarm
Select
Audio Alarm
to generate audio.
•
IP Address
: Enter the IP address and port number of the remote system that will receive the messages.
•
Retry
: Designate how many reattempts to make if message delivery fails.
•
List
: Displays a list of audio files to playback. Click
Add
or
Remove
to add/remove audio files. Select an audio file from the list and then click
Play
to listen to the file.
Please upload a file that a supported format. (.wav,
.mp3) The .wav file supports the formats of 8/16/24bits and 8/12/11.025/16/22.05/24/32/44.1/48/64/96KHz.
28
Part 1 - Remote Setup
FTP Upload
Select
FTP Upload
to upload .jpg image of the event detected to an FTP server.
•
FTP Server
: Click
Add
to register a new FTP server.
Click
Remove
to remove a registered FTP server.
When an event is detected, a .jpg image of the event detected image is uploaded to the Primary Server.
If the upload to the Primary Server fails, the file will be uploaded to the Secondary Server. Upload to the
Secondary Server will continue to be attempted until successful. Fill out the fields below and click
Test
to test the FTP server connection settings. Once the test is complete, click
OK
.
-
FTP Server
: Enter the FTP server’s IP address (or domain name).
-
Upload Path
: Designate the file upload path.
-
Port
: Enter the FTP server’s port number.
-
User ID, Password
: Enter the user ID and password needed for connecting to the FTP server.
•
Settings
: Configure image and upload settings.
-
Upload Type
: Choose an upload type. Select
Always
to upload images using the settings below, irrespective of event detection. Select
Event
to upload images using the settings below when an event is detected.
-
Upload Frequency
: Activated only when Upload
Type has been set to
Always
. Designate the upload speed. The specified number of images will be uploaded to the FTP server during the specified period of time.
-
Upload 1 image per
: Activated only when Upload
Type has been set to
Event
. Designate the upload speed. Select
Upload
for and specify a duration.
Images will be uploaded for the specified duration at the specified upload speed. Select
Upload while event status is active
to upload images at the specified speed only while event status is active.
29
Part 1 - Remote Setup
-
Resolution/Quality
: Choose the resolution and quality of the images to upload to the FTP server.
Range of resolution settings you can use here can vary depe nding on the resolution setting applied under
Video > Streaming
.
-
Base File Name
: Enter a name for the files to be uploaded to the FTP server and then choose file identification options. Select
Add Date/Time Suffix
to add event detection date and time information to each image file. Select
Add Sequence Number
Suffix - max. Count
to number the image files based on the order of event detection. Select
Overwrite
to overwrite the previous image with the new image. Event type is automatically added to the file names.
• When specifying the
Upload Path
or
Base File
Name
, you cannot use special characters such as \, /,
#, *, |, :, ", <, >, and ?.
• The resolution of FTP upload image can change depending on the resolution setting applied under
Video > Streaming
.
• Set speed settings for Upload Frequency and
Upload 1 image per options in consideration of the
FTP server's performance. FTP uploads can fail if the configured speed is higher than what the FTP server can handle.
Record
Select
Record
to record video on the SD memory card.
First, make sure that an SD memory card (Class 6 or higher) has been properly inserted.
•
Type:
Select the record type.
-
Normal Mode:
SD recording is performed according to schedule and setting.
-
Smart Failover:
Used for recording failover in NVR interlock.
•
Total Capacity
: Indicates the SD memory card’s total capacity if it has been inserted properly.
•
Format SD card
: Click on this button to format the inserted SD memory card. Formatting the SD memory card erases all data saved on the card.
This function is only supported for users in
Administrator
group.
•
Record Audio
: Enable/disable audio recording.
30
Schedule
Select the
Schedule
tab and set up a recording schedule.
•
Mode
: Choose a recording mode.
-
Always - Event
: Records video in event mode. In event recording mode, video is recorded when an event is detected.
-
Always - Time-Lapse
: Records video in time lapse mode. In time lapse recording mode, video is recorded continuously, irrespective of event detection.
-
Always - Time-Lapse/Event
: Records video in time lapse mode when event has not been detected and in event mode when one is detected.
-
Date/Time
: Video is recorded in the specified mode according to the dates and times selected in the schedule. Select
On
or
Off
at the bottom of the schedule table and then choose a recording mode.
Click on dates and times on the schedule table or drag to enable/disable recording mode. Select
On
or
Off
and then click
Select All
/
Clear All
to enable/ disable recording mode on all dates and times.
•
Duration
: Specify the event recording duration.
-
Pre-Event
: Select the pre-event recording duration.
You can record up to 60MB of video. Using high resolution, quality, and frame rate settings can cause the recording to exceed the 60MB limit and stop before the end of the specified recording duration.
-
Post-Event
: Select the post-event recording duration.
Part 1 - Remote Setup
Settings
Select the
Settings
tab and configure recording settings.
•
Recording Stream
: Choose a stream to use for recording. It’s possible to designate different streams for different recording modes.
-
Time-Lapse/Pre-Event
: Designate the stream to use for recording in time lapse mode or event mode
(pre-event).
-
Event
: Designate the stream to use for recording in event mode (post-event).
• Recordings saved on the SD memory card can be searched and played back from the IDIS Solution
Suite Compact program or remotely from the remote program. For more information, refer to each program's
operation manual
.
• Video search and playback may not function properly on the remote program while video is being recorded on to the SD memory card.
To remove the SD memory card, unselect the
Record
option and wait 30 seconds before doing so. Removing the SD memory card while recording is in progress of without waiting 30 seconds can damage the system and/or the recording data.
31
Part 1 - Remote Setup
Event
Configure event detection settings.
Alarm In
Select
Alarm In
to enable alarm in event. With alarm in event enabled, alarm in detections by the alarm in connector will be assumed as events.
•
Title
: Enter the alarm-in device’s name.
•
Type
: Select the alarm in type.
•
Event Action
: Select an alarm in event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email:
Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback:
Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm:
Select this option to generate an audio alert and then choose an audio file.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
32
Motion Detection
Select
Motion Detection
to configure motion detection event settings. With motion detection event enabled, motion detections within the designated area will be assumed as events.
Part 1 - Remote Setup time following a motion detection event.
•
Daytime
: Specify when daytime starts and ends. All other times will be assumed as nighttime.
•
Event Action
: Select a motion detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
•
Sensitivity
: Select daytime and nighttime motion detection sensitivity levels. Higher values will result in more sensitive motion detection.
•
Minimum Blocks for Detection
: Select minimum blocks for daytime and nighttime motion detection.
Motion must take place over the selected number of blocks in order for it to be considered as a motion detection event.
•
Motion Zone
: Click
Setup
and define the motion zone using blocks.
-
(Select)/ (Unselect)
: Enable/disable motion detection blocks.
-
(Single Block)
: Select/unselect motion detection blocks individually.
-
(Zone)
: Select/unselect multiple motion detection blocks.
-
(All)
: Select/unselect all motion detection blocks.
•
Motion Ignoring Interval
: With Motion Ignoring
Interval configured, no event log or notification is generated for motions detected during a period of
33
Part 1 - Remote Setup
Trip-Zone
Select
Trip-Zone
to configure trip zone event settings.
With trip zone event enabled, motion detected inside/ outside the selected area will be assumed as an event.
•
Sensitivity
: Select daytime and nighttime motion detection sensitivity levels. Higher values will result in more sensitive motion detection.
•
Trip-Zone
: Click
Setup
and define the trip zone using blocks.
-
(Select)/ (Unselect)
: Enable/disable trip zone blocks.
-
(Single Block)
: Select/unselect trip zone blocks individually.
-
(Zone)
: Select/unselect multiple trip zone blocks.
-
(All)
: Select/unselect all trip zone blocks.
-
Trip Direction
: Define in which direction the motion has to occur in order for it to be considered as an event. Select
In
for movement occurring from outside the trip zone in and
Out
for movement occurring from inside the trip zone out.
•
Motion Ignoring Interval
: With Motion Ignoring
Interval configured, no event log or notification is generated for motions detected during a period of time following a motion detection event.
•
Daytime
: Specify when daytime starts and ends. All other times will be assumed as nighttime.
•
Event Action
: Select a trip zone event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
•
Event Action
settings must be configured correctly in order to perform event actions.
34
Audio Detection
Select
Audio Detection
to configure audio detection event settings. With audio detection enabled, an audio detection taking place during the specified activation period will be assumed as an event.
Sensitivity
: Define the audio detection sensitivity.
Higher values will result in more sensitive detection.
•
Activation Time
: Specify how long audio has to be detected for it to be considered as an event. Audio detections that do not last for the specified duration of time will not be considered as events.
•
Use Ignoring Time
: Define the event ignoring time.
Audio detections taking place during the defined time range will not be assumed as events.
Part 1 - Remote Setup
•
Audio Ignore Interval
: With Audio Ignoring Time configured, no event log or notification is generated for audio detections taking place during a period of time following an audio detection event.
•
Event Action
: Select an audio detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
35
Part 1 - Remote Setup
Tampering
Select
Tampering
to configure tampering detection event settings. With tampering detection event enabled, a sudden change in the video, such as due to movement of the camera or covering up of the lens, will be assumed as an event.
•
Event Action
: Select a tampering detection event alert action.
-
Alarm Out
: Select if you wish to generate an alarm out.
-
Send Email
: Select if you wish to send an email.
Select the
Image Attachment
option to attach a
.jpg image of the event detected to the email.
-
Remote Callback
: Select this option to send a message to a remote system and then select which system to send the message to.
• Not supported from the IDIS Web program.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
-
Audio Alarm
: Select this option to generate an audio alert and then choose an audio file.
-
FTP Upload
: Select this option if you wish to upload images to the FTP server.
-
Record
: Select this option to record video.
Event Action
settings must be configured correctly in order to perform event actions.
•
Sensitivity
: Define the tampering detection sensitivity. Higher values will result in more sensitive detection.
•
Activation time
: Specify how long tampering has to be detected for it to be considered as an event.
Tampering detections that do not last for the specified duration of time will not be considered as events.
•
Use Ignoring Time
: Define the event ignoring time.
Tampering detections taking place during the defined time range will not be assumed as events.
36
System Event
Select
System Event
and configure system event settings. With system event enabled, system status, alarm in status, and disk status will be checked periodically and corresponding alerts will be generated.
•
System Alive
: Select to check the system status and then set up a schedule.
-
Send Email
: Select to send out an email when the system comes on line.
-
Remote Callback
: Select this option to send a message to a remote system when the system comes on line and then select which system to send the message to.
Part 1 - Remote Setup
•
Alarm In Bad:
Select to check the alarm in status and then set up a schedule.
-
Send Email
: Select to send out an email if no change is detected in the alarm in status.
-
Remote Callback:
Select this option to send a message to a remote system when the SD memory card is inserted/removed and then select which system to send the message to.
•
Disk In/Out
: Select to check if the SD memory card has been inserted/removed.
-
Send Email
: Select to send out an email when the
SD memory card is inserted/removed.
-
Remote Callback
: Select this option to send a message to a remote system when the SD memory card is inserted/removed and then select which system to send the message to.
•
and
Remote Callback
settings under
Event
Action
must be configured correctly in order to send out emails and messages.
•
Remote Callback
is not supported on IDIS Web.
• The camera must be registered to the remote system in order to use the
Remote Callback
feature.
37
Part 2 - IDIS Web
IDIS Web is a program that allows you to view and search video from remote locations over the Internet and can be accessed on a Microsoft Internet Explorer or Chrome.
System requirements for running IDIS Web are as follows:
OS: Microsoft
®
Windows
®
XP (Service Pack 3) Internet Explorer only , Microsoft
®
Windows
®
Vista (Service Pack 1),
Microsoft
®
Windows
®
7 (Home Premium, Professional, Ultimate), Microsoft
®
Windows
®
8 (Pro, Enterprise)
• CPU: Intel Pentium IV 2.4GHz or above (Core 2 Duo E4600 recommended)
• RAM: 1GB or more
• VGA: 128MB or more (1280x1024, 24bpp or above)
• Internet Explorer: Version 10 or later 32-bit
• Chrome: Google Chrome 22.0.1229.0 or above (59.xxx or above recommended)
1
Launch Internet Explorer or Chrome and then enter the following information in the address bar.
– http://IP Address:Port Number (IDIS Web connection port number selected during camera IP address and port number setup)
– Or http://FEN Server Address/FEN name (FEN Server address and FEN name registered to the FEN Server)
– Or http://web.idisglobal.com (it is required to enter the camera IP address when logging in. If the camera uses the FEN feature, you can enter the FEN name registered to the FEN server instead of the camera IP address after selecting the USE FEN option)
• If the Use HTTPS option has been selected during IDIS Web port number setup, enter https instead of http. If prompted with a security certificate warning, select "Continue to this website (not recommended)." If the IDIS Web login page fails to load, configure Internet Explorer's settings as follows:
– Tools
→
Internet Options
→
Security
→
Custom Level...
→
Medium-high (default) or Medium.
– Tools
→
Internet Options
→
Advanced
→
Security
→
Use TLS 1.0 (select)
• If connecting by entering an IP address and a port number, you can connect by entering just the IP address if IDIS
Web connection port number has been set to 80 (443 when entering https).
• If connecting by entering http://web.idisglobal.com, it is required to enter the Watch port number.
• Contact your network administrator for the IP address of the camera you wish to connect to the IDIS Web pot number.
38
Part 2 - IDIS Web
2
When prompted with the IDIS Web login window, select
LIVE-PORT
or
PLAY-PORT
as the desired mode. Enter the
ID and password and click
LOGIN
to sign in using the selected mode.
•
• IDIS Web does not work with Microsoft
®
Windows
®
8 metro UI.
• Do not close the login window while IDIS Web is running. Switching over to Web Live or Web Search mode can cause a script error, requiring you to restart the IDIS Web program.
• To use IDIS Web on Microsoft Windows Vista or above, launch Internet Explorer by right-clicking on the icon and selecting the
Run as administrator
option. Otherwise, certain IDIS Web functions might not be available.
• When running IDIS Web, the bottom section of the screen may get cut off if the address bar or the status bar is shown.
In this case, change Internet Options so that the address bar or the status bar is hidden. (
Tools
→
Internet Options
→
Security
→
Custom level...
→
Allow websites to open windows without address or status bars
(
Enable
))
• Launching a new version of IDIS Web for the first time can cause Internet Explorer to load information from the previous version. In this case, navigate to
Tools
→
Internet Options
→
General
, delete temporary Internet files, and then restart IDIS Web.
• On Microsoft Windows Vista or above, lowered image transmission rate can prevent the screen from being displayed or updated. In this case, we recommend that you disable the computer's auto tuning function. Open the command prompt as an administrator. (
Start
→
Accessories
→
Command Prompt
→
Right-Click
and then select
Run as administrator
) Type in "
netsh int tcp set global autotuninglevel=disable
"and then press Enter. Restart the computer to apply the change. To enable auto tuning again, launch the command prompt as an administrator and then type in "
netsh int tcp set global autotuninglevel=normal
". Restart the computer to apply the change.
39
Part 2 - IDIS Web
Web Live Mode
A remote web monitoring program that allows you to monitor images from remote locales in real-time.
2 3 4 5
테스트
1
6
7
8
9
0
!
@
^
#
$
%
4
TYPE 1
5
TYPE 1
6
TYPE 1
TYPE 1
7
8
9
1
2
3
Press to terminate IDIS Web.
Displays the current time.
Click screen.
TYPE 1
to view the video in full screen. Press the ESC key on the keyboard to return to the previous
Click to print the current video screen using a printer connected to the computer.
Click to save the current video screen as an image file.
Click to configure rendering mode and OSD settings. Select rendering mode to adjust the video output rate or select which OSD elements to display on the screen from the OSD list.
Click
Click
to load the camera setup window.
to switch over to Web Search mode.
TYPE 1
40
Part 2 - IDIS Web
0
!
@
#
$
%
^
Shows login information.
Indicates the camera's number.
This function is not supported.
Used to adjust live video quality.
Click to control the alarm out device connected to the camera.
Event status window at the bottom of the screen displays a list of events detected at remote locales.
/
Enable/Disable Alarm In
Motion Detection
Trip zone
Tampering
Audio Detection
Right-click on the screen to display the pop-up menu. Click to enable or disable each function.
•
Fisheye Dewarping:
This function is not supported.
•
Change Camera Title
: Used to change the camera's name.
Renaming the camera in Web Live mode does not affect the camera's name on the remote system. If no name is entered for the camera, the name used at the remote locale is shown on the screen.
•
Enable Audio
: Enables audio transmission with remote locales. Select to display
/
Enables transmission of audio to the remote locale via microphone.
Enables playback of audio from the remote locale on speakers.
Enables two-way audio communication with the remote locale.
Disables audio transmission.
buttons.
icon appears on the corresponding camera screen.
•
Aspect Ratio
: Change the aspect ratio of the video displayed on the screen.
-
Fit to Screen
: Fit the video to the size of the camera screen.
-
Fit to Aspect Ratio
: Resizes camera screen to original aspect ratio of the video.
-
Half Size (x0.5) - 4 Times Bigger (x4)
: Displays the camera videos in the selected size based on the original size of the video. For example, original size (x1) displays the video in its original size. Half size
(x0.5) through 4 times larger (x4) options are only available if there is enough space on the camera screen to accommodate the selected size.
•
MultiStream
: If the camera is running on multi-stream mode, you can choose between the streams.
•
Anti-Aliasing Screen
: Removes stair step effect (blocks) that are caused when zooming a video to improve overall quality of video output.
•
Mouse PTZ Control
: This function is not supported.
41
Part 2 - IDIS Web
Web Search Mode
A remote web search program that allows you to search for recordings from remote locales in real-time.
While in Web Search mode, connection to remote locales will terminate automatically after 30 minutes of inactivity.
2 3 4 5 1
113.49 NC-D320-IP
!
@
#
$
6
7
8
9
0 b
%
^
&
*
(
) a
TYPE 1
TYPE 1
1
2
3
4
5
6
7
Press to terminate IDIS Web.
Displays time information of the video recording from the remote locale.
Click screen.
TYPE 1
to view the video in full screen. Press the ESC key on the keyboard to return to the previous
Click to print the current video screen using a printer connected to the computer.
Click
to save the video recording as an executable file.
to save the current video screen as an image file.
42
Part 2 - IDIS Web
TYPE 1
TYPE 1
8
9
0
!
@
#
$
%
TYPE 1
^
Click to configure rendering mode and OSD settings. Select rendering mode to adjust the video output rate or select which OSD elements to display on the screen from the OSD list.
Click
Shows login information.
Indicates the camera's number.
Zoom in or out on the video.
Adjust image brightness.
Apply image filters (Sharpen, Blur, Equalizer, Interpolation, and Revert) to the images.
Image calibration is applied only during the paused state.
TYPE 1
Use the calendar to search for video recordings by specific dates.
Dates containing video recordings are highlighted in light blue. Selecting a date containing video recording data loads the earliest recording from that date. Selected date is highlighted in orange.
Select to enable time lapse search mode and search/playback video recordings in chronological order. In time lapse search mode, video recordings can be searched by selecting specific dates on the calendar. Time information of video recordings found on the selected dates is shown on the time table at the bottom of the screen. Select a point in time to display video from that moment. If multiple recordings are available for the selected point in time, you can select the desired segment.
Select parameters.
to enable event search mode and search for events matching user-designated
TYPE 1
&
(
)
* a
TYPE 1
TYPE 1
Go to First
TYPE 1 TYPE 1
Play by Frame (backwards)
TYPE 1
Rewind
Play/Pause
TYPE 1
Fast Forward
Play by Frame (forwards)
Go to Last
Click the recording.
to designate recent recordings you wish to search and then jump to a specific point in
Click to reload recent video recordings from remote locales.
Indicates the camera's recording data on a time bar. If the camera's system clock has been changed to a point in the past and more than one recording exists at the same point in time as a result, you will be able to choose which segment to search from the segment menu on the upper right portion of the time table.
43
Part 2 - IDIS Web
b
Right-click on the screen to display the pop-up menu. Click to enable or disable each function.
•
Fisheye Dewarping:
This function is not supported.
•
Change Camera Title
: Used to change the camera's name.
Renaming the camera in Web Search mode does not affect the camera's name on the remote system. If no name is entered for the camera, the name used at the remote locale is shown on the screen.
•
Enable Audio
: If audio was recorded with the video, enabling this option plays audio upon playback.
•
Aspect Ratio
: Change the aspect ratio of the video displayed on the screen.
•
Anti-Aliasing Screen
: Removes stair step effect (blocks) that are caused when zooming a video to improve overall quality of video output.
44
Part 3 - Appendix
Setup Menu Tree (Remote Setup)
Remote Setup
Quick Setup
System
Network
Video
Audio
System
General
Date/Time
User/Group
Network
IP Address
FEN
Port/QoS
Bandwidth Control
Security
IEEE 802.1X
Video
Camera
Streaming
Webcasting
MAT
Privacy Masking
Audio
In/Out
Event Action
Alarm Out
Remote Callback
Audio Alarm
FTP Upload
Record
Event
Alarm In
Motion Detection
Trip zone
Audio Detection
Tampering
System Event
45
Part 3 - Appendix
Index
B
Bitrate Control
C
Camera Name
Compression
D
Date/Time
DSCP
F
FEN Name
FEN Server
Frame Rate
I
IDIS Web port
IPFiltering
M
MAT
N
Network Bandwidth Limit
O
ONVIF Protocol
Q
Quality
R
Remote Port
Resolution
RTSP Port
S
SSL
T
Time Sync
U
Use FEN
Use HTTPS
User/Group
Use UPnP
46 V1.
1
IDIS Co., Ltd.
For more information, please visit at
www.idisglobal.com
Advertisement
