Inovonics EN1224-ON User manual

Inovonics EN1224-ON User manual
2.2 Select the Frequency Band
EN1224/EN1224-ON EchoStream®
Multiple-Condition Pendant Transmitter
Installation Instructions - 05606D
1 Overview
The EN1224 is a four-button, multi-condition pendant transmitter.
The EN1224 must be used with an EchoStream EN4000 of EN4200
serial receiver, or with the EN6040 network coordinator. In addition,
the application controller (e.g. control panel) must be designed to
accept the multiple conditions.
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics
Wireless technical services:
• E-mail: [email protected]
• Phone: (800) 782-2709
1.2 EN1224/EN1224-ON Components
A
C
EchoStream products are able to use a range of radio frequencies,
and must be configured for your geographic area. To configure the
transmitter:
1. Pry the housing apart at either end and pull the two halves
apart.
2. Place a selection jumper on the appropriate frequency band
selection pins.
• Leave the jumper off the pins to set the frequency range to
902-928 MHz for North America.
• Place the jumper on the bottom two pins, marked NZ, to set
the frequency range to 921-928 MHz for New Zealand.
• Place the jumper on the top two pins, marked AU, to set the
frequency range to 915-928 MHz for Australia.
3. Press the Reset button to complete configuration.
Caution: When pressing the Reset button, make sure you don’t
also touch the frequency band selection pins. Touching the
frequency band selection pins while pressing the Reset button can
inadvertently set the pendant to the wrong frequency band.
2.3 Register the Transmitter
The transmitter must be registered with the system in order to be
monitored and supervised. The transmitter will send a check-in
message to the serial receiver or network coordinator.
Pendants using the 868MHz frequency range for Europe will send a
check-in message every 12 minutes; all other transmitters will send
a check-in message every three minutes.
Each pendant has a unique factory-programmed identification
number. Refer to the control panel’s installation instructions for
details on registering a transmitter.
1. When prompted to reset transmitter, press and release the
Reset button.
2. Replace the cover.
3 Operation
Caution: The EchoStream system should be tested regularly to
ensure operation. To test the system, activate each of the
transmitter’s conditions and ensure an appropriate response.
3.1 Activating Conditions
B
Figure 1 EN1224/EN1224-ON components
A Reset button
B Frequency band selection pins
C Battery
2 Installation and Startup
2.1 Install/Replace the Battery
1. Pry the housing apart at either end and pull the two halves
apart.
2. If replacing a battery, remove the old battery.
3. Install the new battery.
4. Press the Reset button to initialize the transmitter.
© 2011 Inovonics - www.inovonics.com
The transmitter can send up to ten conditions. The conditions will
depend on the application, as will the response. The application
controller must be designed to recognize simultaneous messages.
The EN1224 and EN1224-ON require the use of an Inovonics serial
receiver, and cannot currently be used with an Inovonics add-on
receiver.
Condition signals are transmitted multiple times and are indicated
by the blinking transmission LED. Inovonics recommends you test
the transmitter regularly.
4 Specifications
Specifications Typical battery life:
3-5 years Battery type (BAT608): Panasonic CR2 or equivalent
Operating environment 0 to 60°C (32 to 140°F), noncondensing
Note: Specifications and data are subject to change without notice.
Printing Instructions
1. Print Duplex
2. Align and orient back page to match front
page.
3. Cut on dashed line
4. Fold cutsheet in half along the 8.5" axis.
5 Television and Radio Interference
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for
help.
6 FCC Part 15 and Industry Canada
Compliance
This device complies with part 15 of the FCC Rules and Industry
Canada license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit
pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
7 Warranty and Disclaimer
Note: Changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to
operate the equipment.
Inovonics Wireless Corporation ("Inovonics") warrants its products
("Product" or "Products") to conform to its own specifications and to
be free of defects in materials and workmanship under normal use
for a period of thirty-six (36) months from the date of manufacture.
Within the warranty period, Inovonics will repair or replace, at its
option, all or any part of the warranted Product. Inovonics will not be
responsible for dismantling and/or reinstallation charges. To
exercise the warranty, the User ("User", "Installer" or "Consumer")
must work directly through their authorized distributor who will be
given a Return Material Authorization ("RMA") Number by
Inovonics. Details of shipment will be arranged directly through the
authorized distributor.
This warranty is void in cases of improper installation, misuse,
failure to follow installation and operating instructions, alteration,
accident or tampering, and repair by anyone other than Inovonics.
This warranty is exclusive and expressly in lieu of all other
warranties, obligations or liabilities, whether written, oral, express,
or implied. There is no warranty by Inovonics that Inovonics
product will be merchantable or fit for any particular purpose, nor is
there any other warranty, expressed or implied, except as such is
expressly set forth herein. In no event shall Inovonics be liable for
an incidental, consequential, indirect, special, or exemplary
damages, including but not limited to loss of profit, revenue or
contract, loss of use, cost of down time, or interruption of business,
© 2011 Inovonics - www.inovonics.com
nor any claim made by distributor's customers or any other person
or entity.
This warranty will not be modified or extended. Inovonics does not
authorize any person to act on its behalf to modify or extend this
warranty. This warranty will apply only to Inovonics Products.
Inovonics will not be liable for any direct, incidental or consequential
damage or loss whatsoever, caused by the malfunction of Product
due to products, accessories, or attachments of other
manufacturers, including batteries, used in conjunction with
Inovonics Product.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement