SureCall Flare, Flare-C User manual

SureCall Flare, Flare-C User manual

Flare

/ Flare-C

User Guide

Cellular signal booster kit with combined booster and indoor antenna

• Flare Omni kit for voice & 4G data (US)

• Flare Yagi kit for voice & 4G data (CANADA)

• Flare-C Yagi kit for voice & text signal (CANADA)

Introduction

Thank you for purchasing SureCall’s Flare cellular signal booster kit. SureCall’s Flare was specifically designed to eliminate frustrations over dropped calls and limited range by amplifying incoming and outgoing cellular signals in homes and offices.

I f you have any questions during setup, please reach out to our US-based experienced support technicians:

Call: 1-888-365-6283

Email: [email protected]

Or, chat: www.surecall.com, 7:00 am – 5:00 pm PST, Monday – Friday

Watch installation, optimization and troubleshooting techniques on our

SureCall YouTube channel

@SureCall Stay up to date with all things

SureCall

2

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Table of Contents

TABLE OF CONTENTS

How it works .................................................................................................................................... 4

PACKAGE CONTENTS ........................................................................................................................ 5

BEFORE INSTALLATION ..................................................................................................................... 6

Installation Overview ........................................................................................................................ 6

FLARE INSTALLATION ........................................................................................................................ 6

Step 1. Find the Area With the Strongest Signal ............................................................................ 6

Step 2. Install the Outside Antenna ................................................................................................. 7

Step 3. Place the Booster ............................................................................................................... 9

Step 4: Connect to Power ............................................................................................................... 9

Step 5: Enjoy Boosted Signal .......................................................................................................... 9

IF YOU WANT TO IMPROVE PERFORMANCE ................................................................................ 10

LED INDICATORS .............................................................................................................................. 10

TROUBLESHOOTING ........................................................................................................................ 10

FLARE SPECIFICATIONS .................................................................................................................. 11

Kitting Information ......................................................................................................................... 12

FCC & IC INFORMATION ................................................................................................................... 14

WARRANTY ....................................................................................................................................... 15

Three-Year Product Warranty ........................................................................................................ 15

Limitations of Warranty, Damages and Liability ........................................................................... 15

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

3

How It Works

How it works

1. An outside antenna collects signal from the cell tower.

2. The outside antenna sends the signal to the booster through coax cable.

3. The booster amplifies the cell signal and rebroadcasts the signal indoors to all mobile devices within range.

4. The booster amplifies outgoing cell signal back to the tower.

Outside Yagi Antenna (b)

Outside Omni Antenna (a) minim um 25 f t. sepa ration

Cable

Booster

Power Supply

How the SureCall Flare Booster Works

4

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Package Contents

PACKAGE CONTENTS

Unpack all package contents. For missing or damaged items, contact your reseller.

Turn over the signal booster and record the model and serial number for reference:

Serial #: ________________________________________________________________

Purchase Date: __________________________________________________________

Keep the carton and packing material to store the product in case you need to return. Your Flare signal booster package includes the following items:

1. SureCall Flare signal booster

2. Power supply

3. Cable for connecting the outside antenna to the signal booster

4. One outside antenna (either omni or Yagi antenna)

1. Flare Cellular Booster 2. Power Supply 3. Indoor Cable (50 ft.)

4. Outside Antenna Options:

4a. Outside Omni Antenna OR 4b. Outside Yagi Antenna

Warning

:

Unauthorized antennas, cables, and/or coupling devices are prohibited by FCC new rules. Please contact FCC for details: 1-888-CALL-FCC.

Changes or modifications not expressly approved by SureCall could void the user’s authority to operate the equipment.

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

5

6

Before Installation

BEFORE INSTALLATION

1. Prior to securing the location of any booster parts, a “soft install” is recommended as adjustments may be needed to optimize performance.

2. Your planned location for the booster (central to where signal is needed) should be near an existing electrical outlet.

3. Ensure adequate separation between the planned locations of the booster and outside antenna (at least 30 ft.).

4. Ensure sufficient cable length between the outside antenna location and booster location. The length of the provided cable is 50 ft.

Installation Overview

Step 1. Find the outside area with the strongest signal.

Step 2. Install the outside antenna

Step 3. Place the Flare on a table or desktop, center of the area where signal is needed.

Step 4. Connect the booster to an AC power source.

FLARE INSTALLATION

Step 1. Find the Area With the Strongest Signal

Finding Your Strongest Cellular Signal

Using your phone, identify the outside location with the strongest signal. Generally, this is found on the side facing your nearest cell tower and as high as possible.

For specific dB signal measurements, use the methods below. Note that dB measurements appear as a negative number where the closer to 0, the stronger the signal (eg. -100 dB would be considered a weak signal while -65 dB a strong signal).

• Apple iPhones: Dial *3001#12345#* and press Call. In the top-left corner, a dB number appears instead of bars.

• Android devices: download the app

“Network Signal Info” in the Google Play store.

Signal Strength

Poor Good Excellent

Note that Bars are not always a reliable measure of signal.

The best way to confirm signal coverage is the ability to place and hold a call.

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Installation

Step 2. Install the Outside Antenna

After identifying the area of strongest signal, choose the surface where you will mount the outside antenna.

Using the provided hardware, mount the outside antenna at the highest possible elevation, allowing a minimum separation of 25 feet from the planned location of the booster.

Once the outside antenna is secured, connect one end of the provided cable to the outside antenna and tighten the connection.

Do not collocate antennas or operate the outdoor antenna with any other antenna or signal booster.

Option A: Omni Antenna

The omni antenna is omni-directional, which receives and sends signals in a 360º radius.

The provided hardware allow for either a surface mount or pole-mount.

Mount antenna to a vertical surface:

1. Using vertical plate of bracket, mark position of desired placement. The omni

antenna should be mounted in an upright position (See “Omni Outside Antenna Install

Illustration” on page 7)

2. Unscrew nut from end of stucco screw and remove it along with lock washer and regular washer.

Omni antenna with surface mount hardware

3. Place vertical plate into desired location and tap the screws, head first, along with sleeve, into stucco 1/2 to 5/8 inches deep into place.

4. In this order, place washer, lock washer and nut on each screw and tighten until secure. When tightening screw, sleeve will expand to secure plate.

Pole-mount hardware

5. Remove screws from antenna base and use to secure antenna onto horizontal plate.

6. Connect antenna to one end of the provided RG6 cable and tighten the connection. Run the cable along route to planned location of your booster.

Note: Alternate screws may be required for differing surfaces such as wood or concrete.

Outside

Antenna

L-Bracket minim um 25

ft. se parati on

Planned

Booster

Location

Cable

Cable

Screws Nuts &

Washers

Anchors /

Sleeves

Omni Outside Antenna Install Illustration

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

7

Installation

Option B: Outside Yagi Antenna

Before installing a Yagi, or directional antenna, note that the antenna should be mounted on a pole or pipe (not provided), at the highest possible location and mounted horizontally, aimed in the direction of your nearest cell tower. To find the location of your carrier’s closest cell tower, go to www.antennasearch.com.

Ensure that the mounting area has at least a 12-inch radius clear of obstructions and other radiating elements and orient the antenna with the drip hole at the bottom.

Once you have identified your install location, assemble the u-bolt, bracket, nuts and washers onto a pole or pipe (not provided) as shown in the illustration. Keep the connections loose enough to allow the antenna to rotate until the optimum direction is found.

Once the outside antenna is secured to a pipe or pole, connect antenna to one end of the provided RG6 cable and tighten the connection. Run the cable along route to planned location of your booster.

Drip Hole

RG6 Cable

Nut

Washer

Bracket

U-bolt

Outside Antenna Assembly

minim um 25

ft. se parati on

Planned

Booster

Location

Cable

Omni Yagi Antenna Install Illustration

8

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Installation

Step 3. Place the Booster

Place the booster in a central location where signal is needed and at least 25 ft. from the outdoor antenna location.

When placing the booster, note that further separation between the booster and outside antenna will increase booster performance. Connect the open end of the RG6 cable from the outside antenna to the booster and tighten connection.

Please note that the performance and range of your booster depends on three factors:

1. Signal strength at the location of the outside antenna.

2. Interior building materials between the booster and your mobile device.

3. Distance between the outside antenna and booster

(while at least 25 ft. separation is recommended, further separation will increase performance).

Note: Fixed stations operating in the 1710-1755 MHz bands are limited to a maximum antenna height of 10 meters above ground.

This booster should not be used near open fire or flame. Storage and transportation: Store and place in non-extreme roomtemperature and dry environment.

Placing Booster and connecting cable

Step 4: Connect to Power

Once the booster and outside antenna are connected and in place, connect the power cord to the signal booster and plug into a power outlet.

Note: This booster is rated for 5-15V input voltage. DO NOT use the booster with a higher voltage power supply. This can damage the booster, cause personal injury, and void your warranty.

Step 5: Enjoy Boosted Signal

Place a call in the room where the booster is located to confirm that your phone is receiving a boosted signal.

Remember: Bars are not always a reliable measure of signal. The best way to confirm signal coverage is the ability to place and hold a call.

Connecting the Power Supply

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

9

LED Indicators & Troubleshooting

IF YOU WANT TO IMPROVE PERFORMANCE

• Identify a location outside that receives a stronger signal and move the outside antenna to that location (higher is usually better.

• Increase the distance between the booster and outside antenna.

• If using an omni outside antenna, upgrade to a directional yagi antenna that can be aimed toward your closest tower.

Please Note: Changes or modifications not expressly approved by SureCall could void user’s authority to operate the equipment.

LED INDICATORS

LED

Position

Left

Right

Left

Right

LED

Color

Yellow

Yellow

Red

Red /

Yellow

LED

Condition

Flashing

Flashing

Flashing

Alternately

Flashing

Indication

Automatic Gain Control (AGC) is self-adjusting. This is part of normal operation.

Automatic Gain Control (AGC) is preventing oscillation.

If this happens: Increase separation between outside antenna and booster to optimize performance.

The booster is receiving too strong of a signal which could cause the booster to automatically turn off.

If this happens, relocate the outside antenna to a location where the signal is weaker. If using a

Yagi outside antenna, turn in small increments away from cell tower until Red flashing stops.

Booster function has shut off to prevent oscillation.

If this happens: Increased separation between the outside antenna and Flare booster is needed to continue proper operation.

Power LED

10

Left LED

Right LED

Booster LED Diagram

TROUBLESHOOTING

If you have any questions during setup, please reach out to our US-based experienced support technicians:

Call: 1-888-365-6283

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Specifications

Email: [email protected]

Or, chat: www.surecall.com, 7:00 AM – 5:00 PM PST, Monday – Friday

Problem Resolution

Signal booster has no power Connect the power supply to an alternate power source.

Be sure the power source is not controlled by a switch that can remove power from the outlet.

Check the POWER LED ( ) on the signal booster. If it is OFF, return the power supply to SureCall. Contact tech support at to receive an RMA at:

1-888-365-6283 or [email protected], or go to www.surecall.com

7:00 AM – 5:00 PM PST, Monday –

Friday to chat with a representative.

After installing your signal booster system, you have no signal or reception

Verify that cable connections are tightly fitted to the booster and antenna.

Try further separating the booster and antenna.

Verify that there is usable signal where the antenna is placed.

 Remember: Bars are not always a reliable measure of signal. The best way to confirm signal coverage is the ability to place and hold a call.

FLARE SPECIFICATIONS

U.S.

5-Band Kit with Omni

(SC-Poly-DT-O-Kit)

Canada

5-Band Kit with Yagi

(SC-Poly-DT-CA)

Uplink Frequency Range (MHz): 698-716 / 776 – 787 / 824-849 / 1850-1915 / 1710-1755

Downlink Frequency Range (MHz): 728-746 / 746 – 757 / 869-894 / 1930-1995 / 2110-2155

Donor/Server Port Impedance: 75 ohm / 50 ohm

Maximum Gain:

Noise Figure:

72 dB

7 dB

75.1 dB

VSWR:

Supported Standards:

AC Input:

Maximum Output Power:

≤2.0

CDMA, WCDMA, GSM, EDGE, HSPA+, EVDO 4G and all cellular standards

Input: AC 110 – 240 V, 60 Hz ; Output: DC 5V / 3A

1 Watt EIRP

RG6 (50 ft.)

3 Watt EIRP

Cable:

RF Connectors:

Power Consumption:

Weight:

Dimensions:

FCC ID / IC:

Max Coverage Area:

Donor port: F Female, Server port: Integral

<12W

1. 8125 lb.

5.125 × 7.25 × 5.625 inches

RSNDT

2,500 Sq. Ft.

7784A-FLARE

3,000 Sq. Ft.

Dual Band Kit with Yagi

(SC-Dual-DT-Y-CA)

824-849 / 1850-1915

869-894 / 1930-1995

78.9 dB

CDMA, WCDMA, GSM, EDGE,

HSPA+, EVDO

7784A-FLAREDB

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

11

Kitting

12

Kitting Information

Flare 5-Band Kit with Omni (US): SC-Poly-DT-O-Kit

Flare 5-Band Kit with Yagi (Canada): SC-Poly-DT-CA

Component Product number Gain/Loss

Outdoor Antenna* SC-289W

Outdoor Cable*

Indoor Antenna

SC-231W

SC-RG6-50

SC-322W

SC-302W

LTE-A

707 MHz

3 dBi

10 dBi

3.32 dB

2.5 dBi

2.5 dBi

LTE-V

731 MHz

3 dBi

10 dBi

3.32 dB

2.5 dBi

2.5 dBi

Cellular

800 MHz

3 dBi

10 dBi

3.75 dB

3 dBi

3 dBi

PCS

1900 MHz

4 dBi

10 dBi

6.42 dB

5 dBi

5 dBi

AWS

1700 / 2100 MHz

4 dBi / 4 dBi

10 dBi / 10 dBi

6.22 dB / 6.68 dB

4 dBi / 5 dBi

4 dBi / 5 dBi

Note

50 Feet or longer

* The Flare booster is suitable for use with all equivalent and lower gain antennas, as well as, equivalent or greater lengths of cable.

Frequency (MHz)

Uplink: 1710-1755

Uplink: 1850-1915

Uplink: 824-849

Uplink: 698-716

Uplink: 777-787

Bandwidth (MHz)

75.0

75.3

36.3

23.8

24.0

Input (dBm)

-49.4

-49.8

-43.6

-40.1*

-45.9*

Mean Power (dBm)

24.3

21.7

20.6

23.2

18.3

Gain (dB)

73.7

71.5

64.2

63.3

64.2

Downlink: 2110-2155

Downlink: 1930-1995

Downlink: 869-894

86.5

74.4

36.3

-54.7*

-52.3*

-36.7

Downlink: 728-746

Downlink: 746-756

33.8

33.9

-37.7

-32.8

*Mean power: Measurements obtained on section 6.2 where Pmean = P01+3dB

Flare Dual Band Kit with Yagi (Canada): SC-Dual-DT-Y-CA-Kit

Component Product number Gain/Loss

Outdoor Antenna* SC-289W

Cellular - 800 MHz PCS - 1900 MHz

3 dBi 4 dBi

SC-231W 10 dBi 10 dBi

Outdoor Cable*

Indoor Antenna

SC-RG6-50

SC-322W

SC-302W

3.75 dB

3 dBi

3 dBi

6.42 dB

5 dBi

5 dBi

20.4

22.0

20.8

19.4

19.8

Note

50 Feet or longer

75.1

74.3

57.5

57.2

52.6

* The Flare booster is suitable for use with all equivalent and lower gain antennas, as well as, equivalent or greater lengths of cable.

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Kitting

Frequency (MHz)

Uplink: 1850-1915

Uplink: 824-849

Bandwidth (MHz)

75.0

36.8

Input (dBm)

-56.9*

-48.7

Mean Power (dBm)

22.0

20.9

Gain (dB)

78.9

69.6

Downlink: 1930-1995

Downlink: 869-894

75.3

36.5

-45.6

-39.2

21.0

19.8

66.6

59.0

*Input power level is decreased before reaching AGC -0.5 dB to maintain compliance with the intermodulation product of -13 dBm.

Mean power: Measurements obtained on section 6.2 where Pmean = P01+3 dB

Kitting

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

13

FCC, IC & Safety

FCC & IC INFORMATION

Important: Before installing your booster you need to register it with your carrier. You can do so online at the following urls:

Verizon:

http://www.verizonwireless.com/wcms/consumer/register-signal-booster.html

AT&T:

https://securec45.securewebsession.com/attsignalbooster.com/

T-Mobile:

https://support.t-mobile.com/docs/DOC-9827

Sprint:

https://www.sprint.com/legal/fcc_boosters.html

U.S. Cellular:

http://www.uscellular.com/uscellular/support/fcc-booster-registration.jsp

FCC Information:

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.

You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the FCC or a licensed wireless service provider.

This device may be operated ONLY in a fixed location for in-building use.

WARNING: E911 location information may not be provided or may be inaccurate for calls served BY USING THIS DEVICE.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected

• Consult the dealer or an experienced radio/TV technician for help.

Industry Canada:

This Class B digital apparatus meets all requirements of the Canadian Interference Causing Equipment Regulations. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation

Cet appareillage numérique de la classe B répond a toutes les exigencies de l’interférence canadienne causant des réglements d’équipment.

L’opération est sujette aux deux conditions suivantes: (1) ce dispositif peut ne pas causer l’interférence nocive, et (2) ce dispositif doit accepter n’importe quelle intérference reçue, y compris l’intérference qui peut causer l’opération peu désirée.

The Manufacturer’s rated output power of this equipment is for single carrier operation. For situations when multiple carrier signals are present, the rating would have to be reduced by 3.5 dB, especially where the output signal is re-radiated and can cause interference to adjacent band users. This power reduction is to be by means of input power or gain reduction and not by an attenuator at the output of the device.

La puissance de sortie nominale indiquée par le fabricant pour cet appareil concerne son fonctionnement avec porteuse unique. Pour des appareils avec porteuses multiples, on doit réduire la valeur nominale de 3,5 dB, surtout si le signal de sortie est retransmis et qu’il peut causer du brouillage aux utilisateurs de bandes adjacentes. Une telle réduction doit porter sur la puissance d’entrée ou sur le gain, et ne doit pas se faire au moyen d’un atténuateur raccordé à la sortie du dispositif

14

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

Warranty

WARRANTY

Three-Year Product Warranty

To activate your three-year manufacturer’s warranty, register your SureCall product at www.SureCall.com

SureCall warrants its products for three years from the date of purchase against defects in workmanship and/or materials. Specifications are subject to change. The three-year warranty only applies to products meeting the latest FCC Certification Guidelines stated on 2/20/2013 and going into effect April

30, 2014. A two-year warranty applies to any products manufactured before May 1, 2014.

Products returned by customers must be in their original, un-modified condition, shipped in the original or protective packaging with proof-of-purchase documentation enclosed, and a Return Merchandise Authorization (RMA) number printed clearly on the outside of the shipping container.

Buyers may obtain an RMA number for warranty returns by calling the SureCall Return Department toll-free at 1-888-365-6283. Any returns received by

SureCall without an RMA number clearly printed on the outside of the shipping container will be returned to sender. In order to receive full credit for signal boosters, all accessories originally included in the signal booster box must be returned with the signal booster. (The Buyer does not need to include accessories sold in addition to the signal booster, such as antennas or cables.)

This warranty does not apply to any product determined by SureCall to have been subjected to misuse, abuse, neglect, or mishandling that alters or damages the product’s physical or electronic properties.

SureCall warrants to the Buyer that each of its products, when shipped, will be free from defects in material and workmanship, and will perform in full accordance with applicable specifications. The limit of liability under this warranty is, at SureCall’s option, to repair or replace any product or part thereof which was purchased up to THREE YEARS after May 1, 2014 or TWO YEARS for products purchased before May 1, 2014, as determined by examination by SureCall, prove defective in material and/or workmanship. Warranty returns must first be authorized in writing by SureCall. Disassembly of any SureCall product by anyone other than an authorized representative of SureCall voids this warranty in its entirety. SureCall reserves the right to make changes in any of its products without incurring any obligation to make the same changes on previously delivered products.

As a condition to the warranties provided for herein, the Buyer will prepay the shipping charges for all products returned to SureCall for repair, and

SureCall will pay the return shipping with the exception of products returned from outside the United States, in which case the Buyer will pay the shipping charges.

The Buyer will pay the cost of inspecting and testing any goods returned under the warranty or otherwise, which are found to meet the applicable specifications or which are not defective or not covered by this warranty.

Products sold by SureCall shall not be considered defective or non-conforming to the Buyer’s order if they satisfactorily fulfill the performance requirements that were published in the product specification literature, or in accordance with samples provided by SureCall. This warranty shall not apply to any products or parts thereof which have been subject to accident, negligence, alteration, abuse, or misuse. SureCall makes no warranty whatsoever in respect to accessories or parts not supplied by it.

Limitations of Warranty, Damages and Liability:

EXCEPT AS EXPRESSLY SET FORTH HEREIN, THERE ARE NO WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS AS TO

MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR OTHER WARRANTIES, CONDITIONS, GUARANTEES, OR REPRESENTATIONS,

WHETHER EXPRESSED OR IMPLIED, IN LAW OR IN FACT, ORAL OR IN WRITING.

SURECALL AGGREGATE LIABILITY IN DAMAGES OR OTHERWISE SHALL NOT EXCEED THE PAYMENT, IF ANY, RECEIVED BY CELLPHONE-MATE,

INC. FOR THE UNIT OF PRODUCT OR SERVICE FURNISHED OR TO BE FURNISHED, AS THE CASE MAY BE, WHICH IS THE SUBJECT OF CLAIM

OR DISPUTE. IN NO EVENT SHALL SURECALL BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES, HOWSOEVER CAUSED.

All matters regarding this warranty shall be interpreted in accordance with the laws of the State of California, and any controversy that cannot be settled directly shall be settled by arbitration in California in accordance with the rules then prevailing of the American Arbitration Association, and judgment upon the award rendered may be entered in any court having jurisdiction thereof. If one or more provisions provided herein are held to be invalid or unenforceable under applicable law, then such provision shall be ineffective and excluded to the extent of such invalidity or unenforceability without affecting in any way the remaining provisions hereof.

Limitations of Warranty, Damages and Liability

SureCall has made a good faith effort to ensure the accuracy of the information in this document and disclaims the implied warranties of merchantability and fitness for a particular purpose and makes no express warranties, except as may be stated in its written agreement with and for its customers. SureCall shall not be held liable to anyone for any indirect, special or consequential damages due to omissions or errors. The information and specifications in this document are subject to change without notice. © 2017. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners.

SureCall, Inc

48346 Milmont Drive

Fremont, California 94538, USA

888.365.6283 | www.surecall.com

SureCall | 48346 Milmont Drive, Fremont CA 94538 | 1-888-365-6283 | [email protected]

15

SureCall, Inc

48346 Milmont Drive

Fremont, California 94538, USA

888.365.6283 | www.surecall.com

This is a CONSUMER device.

BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider’s consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider.

You MUST operate this device with approved antennas and cables as specified by the manufacturer. Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating this device immediately if requested by the

FCC or a licensed wireless service provider.

WARNING . E911 location information may not be provided or may be inaccurate for calls served by using this device.

This device may be operated ONLY in a fixed location for in-building use.

Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project