Innova FixAssist 3030RS Owner's manual

Innova FixAssist 3030RS Owner's manual
Table of Contents
i
ABOUT THE SCAN TOOL
SAFETY FIRST! .......................................................................
CONTROLS AND INDICATORS ..............................................
DISPLAY FUNCTIONS ............................................................
INITIAL ADJUSTMENTS ..........................................................
1
2
3
5
USING THE SCAN TOOL
CODE RETRIEVAL PROCEDURE ..........................................
ERASING DIAGNOSTIC TROUBLE CODES (DTCs) ..............
ABOUT REPAIRSOLUTIONS 2® ............................................
CONNECTING TO BLUETOOTH / WIFI .................................
6
10
11
12
ADDITIONAL FUNCTIONS
VIEWING VEHICLE INFORMATION .......................................
EVAP TEST ..............................................................................
VIEWING MONITOR ICON DESCRIPTIONS .........................
VIEWING LED DEFINITIONS ..................................................
SELECTING THE DISPLAY LANGUAGE ...............................
ADJUSTING DISPLAY BRIGHTNESS ....................................
ENABLING/DISABLING THE AUDIBLE TONE .......................
ENABLING/DISABLING NAVIGATIONAL FOOTERS .............
VIEWING THE HOTKEY LEGEND ..........................................
SETTING THE UNIT OF MEASUREMENT .............................
14
16
16
17
17
17
18
18
18
19
WARRANTY AND SERVICING
LIMITED ONE YEAR WARRANTY...........................................
SERVICE PROCEDURES .......................................................
21
21
About the Scan Tool
SAFETY FIRST
SAFETY FIRST!
This manual describes common test procedures used by experienced
service technicians. Many test procedures require precautions to avoid
accidents that can result in personal injury, and/or damage to your
vehicle or test equipment. Always read your vehicle's service manual
and follow its safety precautions before and during any test or service
procedure. ALWAYS observe the following general safety precautions:
When an engine is running, it produces carbon monoxide, a
toxic and poisonous gas. To prevent serious injury or death
from carbon monoxide poisoning, operate the vehicle ONLY
in a well-ventilated area.
To protect your eyes from propelled objects as well as hot
or caustic liquids, always wear approved safety eye
protection.
When an engine is running, many parts (such as the coolant
fan, pulleys, fan belt etc.) turn at high speed. To avoid serious
injury, always be aware of moving parts. Keep a safe distance
from these parts as well as other potentially moving objects.
Engine parts become very hot when the engine is running.
To prevent severe burns, avoid contact with hot engine
parts.
P RND L
Before starting an engine for testing or trouble-shooting, make
sure the parking brake is engaged. Put the transmission in
park (for automatic transmission) or neutral (for manual
transmission). Block the drive wheels with suitable blocks.
Connecting or disconnecting test equipment when the
ignition is ON can damage test equipment and the vehicle's
electronic components. Turn the ignition OFF before
connecting the Code Reader to or disconnecting the Code
Reader from the vehicle’s Data Link Connector (DLC).
To prevent damage to the on-board computer when taking
vehicle electrical measurements, always use a digital
multimeter with at least 10 MegOhms of impedance.
The vehicle's battery produces highly flammable hydrogen
gas. To prevent an explosion, keep all sparks, heated items
and open flames away from the battery.
Don't wear loose clothing or jewelry when working on an
engine. Loose clothing can become caught in the fan,
pulleys, belts, etc. Jewelry is highly conductive, and can
cause a severe burn if it makes contact between a power
source and ground.
1
About the Scan Tool
CONTROLS AND INDICATORS
CONTROLS AND INDICATORS
8
5
6
7
1
3
2
4
9
Figure 1. Controls and Indicators
See Figure 1 for the locations of items 1 through 9, below.
1.
ERASE button - Erases Diagnostic Trouble Codes (DTCs) and
"Freeze Frame" data from your vehicle's computer, and resets
Monitor status.
2. DTC/FF button – Displays the DTC View screen and/or scrolls the
LCD display to view DTCs and Freeze Frame data.
3.
ENTER button - When in Menu mode, confirms the selected
option or value.
DOWN button - When in MENU mode, scrolls down through the
4.
menu options. When LINKED to a vehicle, scrolls down through the
current display screen to display any additional data.
5. GREEN LED - Indicates that all engine systems are running
normally (all Monitors on the vehicle are active and performing their
diagnostic testing, and no DTCs are present).
6. YELLOW LED - Indicates there is a possible problem. A “Pending”
DTC is present and/or some of the vehicle's emission monitors have
not run their diagnostic testing.
2
About the Scan Tool
DISPLAY FUNCTIONS
7. RED LED - Indicates there is a problem in one or more of the
vehicle's systems. The red LED is also used to show that DTC(s)
are present. DTCs are shown on the Scan Tool’s LCD display. In
this case, the Malfunction Indicator (“Check Engine”) lamp on the
vehicle's instrument panel will light steady on.
8. Display - Displays test results, Scan Tool functions and Monitor status
information. See DISPLAY FUNCTIONS, below, for details.
9. CABLE - Connects the Scan Tool to the vehicle's Data Link Connector
(DLC).
DISPLAY FUNCTIONS
2
1
15 14
3
4
5
10
11
6
12
7
8
9
13
Figure 2. Display Functions
See Figure 2 for the locations of items 1 through 15, below.
1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area.
2. Monitor icons - Indicate which Monitors are supported by the
vehicle under test, and whether or not the associated Monitor has
run its diagnostic testing (Monitor status). A solid green icon
indicates the associated Monitor has completed its diagnostic
testing. A flashing red icon indicates that the vehicle supports the
associated Monitor, but the Monitor has not yet run its diagnostic
testing.
3.
Vehicle icon - When visible, indicates that the scan tool is being
powered through the vehicle’s DLC connector.
4.
Link icon - When visible, indicates the scan tool is
communicating with the vehicle’s computer.
5.
Computer icon - When visible, indicates the scan tool is linked
to a personal computer.
6. DTC Display Area - Displays the Diagnostic Trouble Code (DTC)
number. Each fault is assigned a code number that is specific to that
fault. The DTC number is color-coded as follows:
3
About the Scan Tool
DISPLAY FUNCTIONS
„
RED - Indicates the currently displayed DTC is a STORED or
PERMANENT DTC.
„
YELLOW - Indicates the currently displayed DTC is a PENDING
DTC.
„
GREEN - In cases where no codes are retrieved, a “No DTCs
are presently stored in the vehicle’s computer” message is
shown in green.
7. Code Number Sequence - The scan tool assigns a sequence
number to each DTC that is present in the computer’s memory,
starting with “1.” This number indicates which code is currently
displayed. Code number “1” is always the highest priority code, and
the one for which “Freeze Frame” data has been stored.
If “1” is a “Pending” code, there may or may not be “Freeze
Frame” data stored in memory.
8. Code Enumerator - Indicates the total number of codes retrieved
from the vehicle’s computer.
9. Test Data Display Area - Displays DTC definitions, Freeze Frame
data and other pertinent test information messages.
10. SYSTEM icon - Indicates the system with which the code is
associated:
MIL icon
11. FREEZE FRAME icon - Indicates that there is Freeze Frame data
from “Priority Code” (Code #1) stored in the vehicle’s computer
memory.
12. Code type - Indicates the type of code being displayed; Generic
Stored, Generic Pending, Generic permanent, etc.
13. Severity - Indicates the level of severity for the priority code (code
number “1”), as follows:
1 - Service should be scheduled and repairs made when
convenient. This DTC typically has no immediate threat to
essential system components in the short term.
2 - Repair immediately if drivability issues are present. Threat to
essential system components if not repaired as soon as possible.
3 - Stop and repair vehicle immediately to prevent interrelated
failures. Harmful and damaging to essential system components.
4
14.
Bluetooth icon – Indicates communication status with a
compatible
Innova
mobile
application
(please
visit
www.innova.com/apps for more information). A solid blue icon
indicates an active Bluetooth connection has been established. A
solid grey icon indicates Bluetooth is not connected.
15.
WiFi icon – Indicates WiFi communication status. When ON,
indicates the scan tool is linked to a WiFi network. When OFF,
indicates there is no WiFi connection.
About the Scan Tool
INITIAL ADJUSTMENTS
INITIAL ADJUSTMENTS
The first time the unit is connected to a vehicle, you must select the
desired display language (English, French or Spanish) and unit of
measurement (USA or Metric) as follows:
1. Select the desired display language, then press ENTER
„
.
The Select Unit screen displays.
2. Select the desired unit of measurement, then press ENTER
.
After the initial language and unit of measurement selections
are performed, these, as well as other settings, can be
changed as desired. Proceed to Additional Functions on page
14 for further instructions.
5
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
CODE RETRIEVAL PROCEDURE
Retrieving and using Diagnostic Trouble Codes (DTCs) for
troubleshooting vehicle operation is only one part of an
overall diagnostic strategy.
Never replace a part based only on the DTC definition.
Each DTC has a set of testing procedures, instructions
and flow charts that must be followed to confirm the
location of the problem. Always refer to the vehicle's
service manual for detailed testing instructions.
Check your vehicle thoroughly before performing
any test.
ALWAYS observe safety precautions whenever working on a
vehicle.
1. Turn the ignition off.
2. Locate the vehicle's 16-pin Data Link
Connector (DLC).
Some DLCs have a plastic cover
that must be removed before
connecting the Scan Tool.
If the Scan Tool is ON, turn it OFF
BEFORE connecting to the DLC.
3. Connect the Scan Tool to the vehicle's
DLC. The cable connector is keyed and
will only fit one way.
„
If you have problems connecting the
cable connector to the DLC, rotate
the connector 180°.
If you still have problems, check the
DLC on the vehicle and on the Scan
Tool.
4. Turn the ignition on. DO NOT start the
engine.
5. When the Scan Tool is properly
connected to the vehicle’s DLC, the
Scan Tool will automatically turn ON.
6
„
If the unit does not power on automatically, it may indicate there
is no power present at the vehicle’s DLC connector. Check the
fuse panel and replace any burned-out fuses.
„
If replacing the fuse(s) does not correct the problem, consult
your vehicle’s repair manual to identify the proper computer
(PCM) fuse/circuit, and perform any necessary repairs before
proceeding.
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
6. The Scan Tool automatically starts a check of the vehicle’s
computer to determine which type of communication protocol it is
using. When the Scan Tool identifies the computer’s communication
protocol, a communication link is established.
A PROTOCOL is a set of rules and procedures for regulating data
transmission between computers, and between testing equipment
and computers. As of this writing, five different types of protocols
(ISO 9141, Keyword 2000, J1850 PWM, J1850 VPW and CAN)
are in use by vehicle manufacturers.
„
If the Scan Tool fails to link to the vehicle’s computer, a
“Communication Error” message shows.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press ENTER
„
to continue.
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press and hold ENTER
to return to the Main Menu.
- Turn the ignition off, and disconnect the Scan Tool.
- Contact Technical Support for assistance.
7. If the Scan Tool can decode the Vehicle
Identification Number (VIN) for the
vehicle under test, the Confirm Vehicle
screen displays.
„
If the information shown is correct for the vehicle under test,
select Yes, then press ENTER
. Proceed to step 9.
„
If the information shown is not correct for the vehicle under test,
or if you wish to manually select the vehicle, select No, then
press ENTER
. Proceed to step 8.
„
If the Scan Tool cannot decode the Vehicle Identification
Number (VIN) for the vehicle under test, the Select Vehicle
screen displays. Proceed to step 8.
8. When No is selected from the Vehicle
information screen, the Select Make
screen displays.
„
Select the desired vehicle make,
then press ENTER
to continue.
-
„
The Vehicle Information screen
displays.
If the information shown is correct for the vehicle under test,
select Yes, then press ENTER
. Proceed to step 9.
7
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
„
If the information shown is not correct for the vehicle under test,
or if you wish to reselect the vehicle, select No, then press
ENTER
to return to the Select Make screen.
9. After approximately 10~60 seconds, the Scan Tool will retrieve and
display any Diagnostic Trouble Codes, Monitor Status and Freeze
Frame Data retrieved from the vehicle’s computer memory.
„
The Scan Tool will display a code only if codes are present. If no
codes are present, the message “No Powertrain DTCs or Freeze
Frame Data presently stored in the vehicle’s computer” displays.
„
The Scan Tool is capable of retrieving and storing up to 32 codes in
memory, for immediate or later viewing.
10. Refer to DISPLAY FUNCTIONS on page 3 for a description of
display elements.
In the case of long code
definitions, or when viewing
Freeze Frame Data, a small arrow
is shown in the upper/lower righthand corner of the Scan Tool
display area to indicate the
presence of additional information.
If a definition for the currently displayed code is not available,
an advisory message shows.
11. Read and interpret Diagnostic Trouble Codes/system condition
using the display and the green, yellow and red LEDs.
The green, yellow and red LEDs are used (with the LCD
display) as visual aids to make it easier to determine engine
system conditions.
„
Green LED – Indicates that all engine
systems are “OK” and operating
normally. All monitors supported by
the vehicle have run and performed
their diagnostic testing, and no trouble
codes are present. All Monitor icons
will be solid.
„
Yellow LED - Indicates one of the
following conditions:
A. A PENDING CODE IS PRESENT – If
the yellow LED is illuminated, it may
indicate a Pending code is present.
Check the display for confirmation. A
Pending code is confirmed by the
presence of a numeric code and the
word PENDING.
8
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
B. MONITOR NOT RUN STATUS – If
the display shows a zero (indicating
there are no DTC’s present in the
vehicle’s computer memory), but the
yellow LED is illuminated, it may be
an indication that some of the
Monitors supported by the vehicle
have not yet run and completed their
diagnostic testing. Check the display
for confirmation. All Monitor icons that
are blinking have not yet run and
completed their diagnostic testing; all
Monitor icons that are solid have run
and completed their diagnostic testing.
„
Red LED - Indicates there is a
problem with one or more of the
vehicle's systems. The red LED is
also used to show that DTC(s) are
present. In this case, the Malfunction
Indicator (Check Engine) lamp on the
vehicle's instrument panel will light
steady on.
„
DTC’s that start with “P0”, “P2” and some “P3” are
considered Generic (Universal). All Generic DTC definitions
are the same on all OBD2 equipped vehicles. The Scan Tool
automatically displays the code definitions (if available) for
Generic DTC’s.
„
DTC’s that start with “P1” and some “P3” are Manufacturer
specific codes and their code definitions vary with each vehicle
manufacturer.
12. If more than one DTC was retrieved, and to view Freeze Frame
Data, press and release DTC/FF, as necessary.
„
Each time DTC/FF is pressed and released, the Scan Tool will
scroll and display the next DTC in sequence until all DTCs in its
memory have displayed.
„
Freeze Frame data (if available) will display after DTC #1.
„
In OBD2 systems, when an emissions-related engine malfunction occurs that causes a DTC to set, a record or snapshot of engine conditions
at the time that the malfunction
occurred is also saved in the vehicle’s
computer memory. The record saved
is called Freeze Frame data. Saved
engine conditions include, but are not
limited to: engine speed, open or closed loop operation, fuel system
commands, coolant temperature, calculated load value, fuel
pressure, vehicle speed, air flow rate, and intake manifold pressure.
9
Using the Scan Tool
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
If more than one malfunction is present that causes more than
one DTC to be set, only the code with the highest priority will
contain Freeze Frame data. The code designated “01” on the
Scan Tool display is referred to as the PRIORITY code, and
Freeze Frame data always refers to this code. The priority
code is also the one that has commanded the MIL on.
13. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” Code.
14. Determine engine system(s) condition by viewing the display for any
retrieved Diagnostic Trouble Codes, code definitions and Freeze
Frame data, and interpreting the green, yellow and red LEDs.
„
If DTC’s were retrieved and you are going to perform the repairs
yourself, proceed by consulting the Vehicle’s Service Repair
Manual for testing instructions, testing procedures, and flow
charts related to retrieved code(s).
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
When the Scan Tool’s ERASE function is used to erase
DTCs from the vehicle's on-board computer, "Freeze
Frame" data and manufacturer-specific enhanced data are
also erased. "Permanent" DTCs ARE NOT erased by the
ERASE function.
If you plan to take the vehicle to a Service Center for repair, DO NOT
erase the codes from the vehicle's computer. If the codes are erased,
valuable information that might help the technician troubleshoot the
problem will also be erased.
Erase DTCs from the computer's memory as follows:
When DTCs are erased, the I/M Readiness Monitor Status
program resets status of all Monitors to a not run condition. To
set all Monitors to a DONE status, an OBD2 Drive Cycle must
be performed.
1. If not connected already, connect the
Scan Tool to the vehicle's DLC, and
turn the ignition "On.” (If the Scan Tool
is already connected and linked to the
vehicle's computer, proceed directly to
step 3. If not, continue to step 2.)
2. Perform the Code Retrieval procedure
as described on page 6.
10
„
To erase OBD2 DTCs: Wait until
the codes are displayed, then
proceed to step 3.
„
Press and release ERASE
. A confirmation message shows.
Using the Scan Tool
ABOUT REPAIRSOLUTIONS 2®
„
If you are sure you want to proceed,
.
select YES, then press ENTER
„
If you do not want to proceed, select
to
NO, then press ENTER
cancel the erase procedure.
„
If you chose to erase DTCs, a “One
moment
please…”
message
displays while the erase function is
in progress.
If the vehicle’s engine is running, an advisory message shows.
Turn the engine OFF, then turn the ignition back to ON. DO NOT
start the engine. Press ENTER
to continue.
„
If the erase was successful, a
confirmation message shows. The
Scan Tool automatically relinks to the
vehicle’s computer after 3 seconds.
If the erase was not successful and
ECU error code $22 is present, an
advisory message displays. Start
the engine and maintain vehicle
speed at 0. Choose Erase DTCs to
try again.
„
If the erase was not successful, an advisory message shows
indicating the erase request was sent to the vehicle’s computer.
The Scan Tool automatically relinks to the vehicle’s computer
after 3 seconds.
ABOUT REPAIRSOLUTIONS 2®
RepairSolutions 2® is a web-based service created to assist both Do-ItYourself and Professional technicians in quickly and accurately
diagnosing and repairing today’s vehicles. RepairSolutions 2 allows you
to view and save the diagnostic data retrieved from a vehicle’s on-board
computer(s) using your Code Reader. At the core of RepairSolutions 2
is an extensive knowledge database, developed by compiling and
analyzing years worth of “real world” vehicle service data.
RepairSolutions 2 builds on manufacturer-recommended diagnostic and
repair information by providing verified, vehicle-specific fixes supplied by
ASE technicians across the country. RepairSolutions 2 also provides
access to an extensive knowledge database including:
„
Verified Fixes – Find the most likely fixes reported and verified by
ASE Technicians for the retrieved DTCs.
„
Repair Instructions – View available repair instructions to properly
perform the fix.
„
Video Tutorials – Watch repair video tutorials for valuable repair
tips.
11
Using the Scan Tool
CONNECTING TO BLUETOOTH / WIFI
„
Technical Service Bulletins – Research known problems reported
by vehicle manufacturers.
„
Safety Recalls – Research known safety concerns applicable to a
vehicle.
And much more. Please visit www.innova.com for additional information.
Hardware Requirements:
„
Innova Scan Tool with Bluetooth/WiFi
„
Android or iOS Smart Device
Accessing RepairSolutions 2®
1. Download and install the RepairSolutions 2® app from the App
Store (for iOS devices) or Google Play (for Android devices).
2. Launch the RepairSolutions 2 app and log in to your account.
„
If you have not yet established an account, you must register for
a FREE RepairSolutions 2 account before proceeding.
3. Connect the Code Reader to a vehicle and establish a Bluetooth or
WiFi connection with your Smart Device (refer to CONNECTING TO
BLUETOOTH / WIFI, below). Be sure your Smart Device is
connected to an available WiFi network.
„
The RepairSolutions 2 app will store two WiFi configurations
only.
4. Retrieve diagnostic data (refer to CODE RETRIEVAL PROCEDURE
on page 6 for details).
5. The RepairSolutions 2 app automatically displays a report based on
the retrieved diagnostic data.
„
If the Code Reader is not connected to WiFi or Bluetooth,
vehicle data will not be saved.
CONNECTING TO BLUETOOTH / WIFI
Launch the RepairSolutions2 app an follow the prompts to establish
Bluetooth and (optionally) WiFi connections, as follows:
1. Launch the RepairSolutions2 app. Select Wifi Tools Settings from
the menu. Power on your Code Reader, then select from the list of
available devices.
2. When Bluetooth pairing is complete, a confirmation screen displays.
Click Continue.
„
If a Bluetooth connection cannot be established, an advisory
message displays. Tap Try Again to repeat the pairing process.
3. Follow the on-screen prompts to connect to an available WiFi
network.
„
12
You can automatically connect to the network your Smart Device
is currently connected to, or you can manually connect to
another available network.
Using the Scan Tool
CONNECTING TO BLUETOOTH / WIFI
„
Note that only 2.4GHz networks are supported.
„
If you do not wish to connect to a WiFi network at this time, tap
SKIP.
4. When WiFi pairing is complete, a confirmation screen displays. Click
Continue to view the “Setup Complete” message, then click
Continue to enter RepairSolutions2.
„
If a WiFi connection cannot be established, an advisory
message displays. Tap Try Again to repeat the pairing process.
13
Additional Functions
VIEWING VEHICLE INFORMATION
In addition to retrieving Diagnostic Trouble Codes (DTCs), you can use
the scan tool to perform additional diagnostic tests, to view diagnostic
and vehicle information stored in your vehicle's on-board computer, and
to configure the scan tool for your particular needs. Additional tests and
related functions are accessed through the Main Menu. The following
functions are available:
„
Vehicle Information – Displays the
Vehicle Info menu, which lets you
retrieve and view reference information
for the vehicle under test.
„
EVAP Test – Lets you initiate a test of
the vehicle’s EVAP system.
„
Monitor Icons – Shows the full names
for the I/M MONITOR STATUS icons.
„
LED Definitions – Provides descriptions of the meaning of the Scan
Tool SYSTEM STATUS LEDs.
„
Language Selection – sets the display language for the Scan Tool
to Englis, French or Spanish.
„
Adjust Brightness – Adjusts the brightness of the display screen.
„
Audible Tone – Turns the Scan Tool’s audible tone “o” and “off.”
When turned “on,” a tone sounds each time a button is pressed.
„
Footer – Turns the navigational “footers” at the bottom of most
display screens “on” and “off.”
„
Hotkey Legend – Shows functional descriptions for the Scan Tool’s
hotkeys.
„
Unit of Measurement – sets the unit of measurement for the Scan
Tool’s display to USA or Metric.
To access the Main Menu:
„
Press and hold ENTER
.
- The Main Menu displays.
VIEWING VEHICLE INFORMATION
The Scan Tool offers three options for
retrieving reference information for the
vehicle under test; Vehicle ID, Available
Modules and IPT (In-use Performance
Tracking).
Retrieving Vehicle ID Information
The Vehicle ID function is applicable to model year 2000 and
newer OBD2-compliant vehicles.
The Scan Tool can retrieve a list of information (provided by the vehicle
manufacturer), unique to the vehicle under test, from the vehicle's onboard computer. This information may include:
14
Additional Functions
VIEWING VEHICLE INFORMATION
„
The vehicle's VIN number
„
The control module identification number
„
The vehicle's calibration ID(s). These IDs uniquely identify the
software version(s) for the vehicle's control module(s).
„
The Vehicle's Calibration Verification Number(s) (CVNs) required by
ODB2 regulations. CVNs are used to determine if emission-related
calibrations for the vehicle under test have been changed. One or
more CVNs may be returned by the vehicle's computer.
1. Select Vehicle Information from the Main Menu, then press
ENTER
.
„
The Vehicle Information menu displays.
.
2. Select Vehicle ID, then press ENTER
The first time the Vehicle ID function is used, it may take several
minutes to retrieve the information from the vehicle's computer.
3. When the retrieval process is completed,
the vehicle ID information displays.
4. When you have finished viewing the
retrieved vehicle ID information, press
to return to the
and hold ENTER
Main Menu.
Viewing Available Modules
The Scan Tool can retrieve a list of modules supported by the vehicle
under test.
1. Select Vehicle Information from the Main Menu, then press
ENTER
.
„
The Vehicle Information menu displays.
2. Select Available Modules, then press
ENTER
.
3. When the retrieval process is completed,
a complete list of modules supported by
the vehicle under test displays.
4. When you have finished viewing the list of available modules, press
and hold ENTER
to return to the Main Menu.
Viewing In-use Performance Tracking (IPT)
The Scan Tool can retrieve In-use Performance Tracking (IPT) statistics
for monitors supported by the vehicle under test. Two values are
returned for each monitor; the number of times that all conditions
necessary for a specific monitor to detect a malfunction have been
encountered (XXXCOND), and the number of times that the vehicle has
been operated under the specific conditions for the monitor (XXXCOMP).
Statistics are also provided for the number of times the vehicle has been
operated in OBD monitoring conditions (OBDCOND), and the number of
times the vehicle’s engine has been started (IGNCNTR).
15
Additional Functions
EVAP TEST- VIEWING MONITOR ICON DESCRIPTIONS
1. Select Vehicle Information from the
Main Menu, then press ENTER
.
„
The Vehicle
displays.
Information
2. Select IPT, then press ENTER
menu
.
3. When the retrieval process is completed,
the In-use Performance Tracking
statistics for the vehicle under test
display.
„
If In-use Performance Tracking is not available for your vehicle,
an advisory message shows on the diagnostic tool’s display.
Press and hold ENTER
to return to the Main Menu.
4. When you have finished viewing the statistics, press and hold
to return to the Main Menu.
ENTER
EVAP TEST
The EVAP Test function lets you initiate a leak test for the vehicle's
EVAP system.
The Scan Tool does not perform the leak test, but signals to
vehicle's on-board computer to initiate the test. The vehicle
manufacturer determines the criteria and method for stopping
the test once it has been started. Refer to the vehicle's service
repair manual to determine the procedures necessary to stop
the test.
1. From the Main Menu, select EVAP Test, then press ENTER
.
2. A "One moment please..." message
displays.
3. When the EVAP leak test has been
initiated by the vehicle's on-board
computer, a confirmation message
displays.
„
Press ENTER
to exit.
Some vehicle manufacturers do not allow diagnostic tools or other
external devices to control vehicle systems. If the EVAP Test is
not supported by the vehicle under test, an advisory message
shows on the Scan Tool's display. Press ENTER
to exit.
VIEWING MONITOR ICON DESCRIPTIONS
The I/M MONITOR STATUS icons on the Scan Tool’s LCD display
provide an indication of the “Completed / Not Complete” status for all I/M
Monitors supported by the vehicle under test. The Monitor Icons
function displays the full name for each Monitor icon.
16
Additional Functions
LED DEFINITIONS - DISPLAY LANGUAGE - DISPLAY BRIGHTNESS
1. From the Main Menu, select Monitor
Icons, then press ENTER
.
„
The Monitor Icons screen displays.
„
The screen shows a list of the 15
Monitor icons, along with the full name
for each icon. Use the DOWN
button, as necessary, to scroll the list.
2. When you have finished viewing the Monitor icon descriptions, press
to return to the Main Menu.
and hold ENTER
VIEWING LED DEFINITIONS
The SYSTEM STATUS LEDs on the scan tool provide a visual
indication of the I/M Readiness status of the vehicle under test. The
LED Definitions function provides a description of the meanings of the
green, yellow and red SYSTEM STATUS LEDs.
1. From the Main Menu, select LED
Definitions, then press ENTER
.
„
The LED Definitions screen displays.
„
The screen provides a description of
the meanings of the green, yellow
and red SYSTEM STATUS LEDs.
2. When you have finished viewing the
LED meanings, press and hold ENTER
to return to the Main Menu.
SELECTING THE DISPLAY
LANGUAGE
1. Select Language Selection in the Main
.
Menu, then press ENTER
„
The Language Selection screen displays.
2. Select the desired display language, then
press ENTER
to save your changes.
To return to the Main Menu without making changes, press
.
and hold ENTER
ADJUSTING DISPLAY BRIGHTNESS
1. Select Adjust Brightness in the Main
Menu, then press ENTER
.
„
The Adjust
displays.
Brightness
screen
2. Select Darker or Lighter, as desired,
.
then press ENTER
17
Additional Functions
AUDIBLE TONE - NAVIGATIONAL FOOTERS - HOTKEY LEGEND
3. Repeat steps 1 and 2 as needed until the desired brightness is
obtained.
To return to the Main Menu without making changes, press
.
and hold ENTER
ENABLING/DISABLING THE AUDIBLE TONE
1. Select Audible Tone in the Main Menu,
then press ENTER
.
„
The Audible Tone screen displays.
2. Select On or Off as desired, then press
ENTER
to save your changes.
To return to the Main Menu
without making changes, press
.
and hold ENTER
ENABLING/DISABLING NAVIGATIONAL FOOTERS
1. Select Footer in the Main Menu, then
press ENTER
.
„
The Footer screen displays.
2. Select On of Off as desired, then
to save your
press ENTER
changes.
To return to the Main Menu
without making changes, press
.
and hold ENTER
VIEWING THE HOTKEY LEGEND
1. Select Hotkey Legend in the Main
Menu, then press ENTER
.
„
The Hotkey Legends screen displays.
„
The screen shows a functional
description of each of the scan
tool’s hotkeys.
2. When you have finished viewing the
Hotkey Legend, press and hold ENTER
.
18
Additional Functions
SETTING THE UNIT OF MEASUREMENT
SETTING THE UNIT OF MEASUREMENT
1. Select Unit of Measurement in the Main
Menu, then press ENTER
.
„
The Unit of Measurement screen
displays.
2. Select the desired unit of measurement,
then press ENTER
to save your
changes.
To return to the Main Menu without making changes, press
.
and hold ENTER
19
Notes
20
Warranty and Servicing
LIMITED ONE YEAR WARRANTY
The Manufacturer warrants to the original purchaser that this unit is free
of defects in materials and workmanship under normal use and
maintenance for a period of one (1) year from the date of original
purchase.
If the unit fails within the one (1) year period, it will be repaired or
replaced, at the Manufacturer’s option, at no charge, when returned
prepaid to the Service Center with Proof of Purchase. The sales receipt
may be used for this purpose. Installation labor is not covered under this
warranty. All replacement parts, whether new or remanufactured,
assume as their warranty period only the remaining time of this warranty.
This warranty does not apply to damage caused by improper use,
accident, abuse, improper voltage, service, fire, flood, lightning, or other
acts of God, or if the product was altered or repaired by anyone other
than the Manufacturer’s Service Center.
The Manufacturer, under no circumstances shall be liable for any
consequential damages for breach of any written warranty of this unit.
This warranty gives you specific legal rights, and you may also have
rights, which vary from state to state. This manual is copyrighted with all
rights reserved. No portion of this document may be copied or
reproduced by any means without the express written permission of the
Manufacturer. THIS WARRANTY IS NOT TRANSFERABLE. For
service, send via U.P.S. (if possible) prepaid to Manufacturer. Allow 3-4
weeks for service/repair.
SERVICE PROCEDURES
If you have any questions, require technical support or information on
UPDATES and OPTIONAL ACCESSORIES, please contact your local
store, distributor or the Service Center.
USA & Canada:
(800) 544-4124 (6:00 AM-6:00 PM, Monday through Saturday)
All others:
Saturday)
(714) 241-6802 (6:00 AM-6:00 PM, Monday through
FAX: (714) 241-3979 (24 hr.)
Web: www.innova.com
21
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement