Innova 5310 Owner's manual

Innova 5310 Owner's manual
Table of Contents
SAFETY PRECAUTIONS
SAFETY FIRST! ..................................................................
1
SCAN TOOL CONTROLS
i
CONTROLS AND INDICATORS ..........................................
DISPLAY FUNCTIONS ........................................................
INITIAL ADJUSTMENTS ......................................................
2
3
5
USING THE SCAN TOOL
CODE RETRIEVAL PROCEDURE ..........................................
THE SYSTEM MENU................................................................
VIEWING OEM ENHANCED DTCs .........................................
VIEWING OEM ENHANCED DTCs (Ford/Mazda only) ...........
VIEWING ABS DTCs ...............................................................
VIEWING SRS DTCs ................................................................
ERASING DIAGNOSTIC TROUBLE CODES (DTCs) .............
ABOUT REPAIRSOLUTIONS® ...............................................
CONNECTING TO BLUETOOTH / WIFI .................................
6
11
11
12
14
15
16
18
19
LIVE DATA MODE
VIEWING LIVE DATA ..............................................................
CUSTOMIZING LIVE DATA (PIDs) ..........................................
RECORDING (CAPTURING) LIVE DATA ...............................
LIVE DATA PLAYBACK ...........................................................
20
21
22
26
ADDITIONAL TESTS
SYSTEM TEST MENU .............................................................
RESETTING THE OIL MAINTENANCE LIGHT .......................
PERFORMING A SERVICE CHECK .......................................
BATTERY/ALTERNATOR TEST .............................................
USING THE DLC LOCATOR ...................................................
VIEWING VEHICLE INFORMATION .......................................
VIEWING THE FIRMWARE VERSION ....................................
THE TOOL LIBRARY ...............................................................
ADJUSTMENTS AND SETTINGS ...........................................
28
31
32
33
35
35
37
38
40
WARRANTY AND SERVICING
LIMITED ONE YEAR WARRANTY...........................................
SERVICE PROCEDURES .......................................................
45
45
Safety Precautions
SAFETY FIRST!
SAFETY FIRST!
This manual describes common test procedures used by experienced
service technicians. Many test procedures require precautions to avoid
accidents that can result in personal injury, and/or damage to your
vehicle or test equipment. Always read your vehicle's service manual
and follow its safety precautions before and during any test or service
procedure. ALWAYS observe the following general safety precautions:
When an engine is running, it produces carbon monoxide,
a toxic and poisonous gas. To prevent serious injury or
death from carbon monoxide poisoning, operate the vehicle
ONLY in a well-ventilated area.
To protect your eyes from propelled objects as well as hot
or caustic liquids, always wear approved safety eye
protection.
When an engine is running, many parts (such as the
coolant fan, pulleys, fan belt etc.) turn at high speed. To
avoid serious injury, always be aware of moving parts.
Keep a safe distance from these parts as well as other
potentially moving objects.
Engine parts become very hot when the engine is running.
To prevent severe burns, avoid contact with hot engine parts.
P RND L
Before starting an engine for testing or troubleshooting,
make sure the parking brake is engaged. Put the
transmission in park (for automatic transmission) or
neutral (for manual transmission). Block the drive wheels
with suitable blocks.
Connecting or disconnecting test equipment when the
ignition is ON can damage test equipment and the vehicle's
electronic components. Turn the ignition OFF before
connecting the Scan Tool to or disconnecting the Scan
Tool from the vehicle’s Data Link Connector (DLC).
To prevent damage to the on-board computer when taking
vehicle electrical measurements, always use a digital
multimeter with at least 10 megOhms of impedance.
Fuel and battery vapors are highly flammable. To prevent
an explosion, keep all sparks, heated items and open
flames away from the battery and fuel / fuel vapors. DO
NOT SMOKE NEAR THE VEHICLE DURING TESTING.
Don't wear loose clothing or jewelry when working on an
engine. Loose clothing can become caught in the fan,
pulleys, belts, etc. Jewelry is highly conductive, and can
cause a severe burn if it makes contact between a power
source and ground.
1
Scan Tool Controls
CONTROLS AND INDICATORS
CONTROLS AND INDICATORS
14
13
10
12
7
11
1
4
2
5
3
6
9
8
Figure 1. Controls and Indicators
See Figure 1 for the locations of items 1 through 14, below.
1.
ERASE button - Erases Diagnostic Trouble Codes (DTCs),
and “Freeze Frame” data from your vehicle’s computer, and resets
Monitor status.
2.
SYSTEM MENU button – When pressed, displays the System
Test Menu.
3. DTC/FF button - Displays the DTC View screen and/or scrolls the
LCD display to view DTCs and Freeze Frame data.
4.
LINK button - When connected to a vehicle, links the Scan Tool
to the vehicle’s PCM.
5. M button – When pressed, displays the Main Menu.
2
Scan Tool Controls
DISPLAY FUNCTIONS
6. LD button – When pressed while linked to a vehicle, places the
Scan Tool in Live Data mode.
7.
UP button – When in MENU mode, scrolls UP through the
menu options. When LINKED to a vehicle, scrolls UP through the
current display screen to display any additional data.
8.
ENTER button - When in MENU mode, confirms the selected
option or value.
9.
DOWN button - When in MENU mode, scrolls DOWN through
the menu options. When LINKED to a vehicle, scrolls DOWN
through the current display screen to display any additional data.
10. GREEN LED - Indicates that all engine systems are running
normally (all Monitors on the vehicle are active and performing their
diagnostic testing, and no DTCs are present).
11. YELLOW LED - Indicates there is a possible problem. A “Pending”
DTC is present and/or some of the vehicle’s emission monitors have
not run their diagnostic testing.
12. RED LED - Indicates there is a problem in one or more of the
vehicle’s systems. The red LED is also used to show that DTC(s)
are present. DTCs are shown on the Scan Tool’s display. In this
case, the Malfunction Indicator (“Check Engine”) lamp on the
vehicle’s instrument panel will light steady on.
13. Display - Color LCD display shows menu and submenus, test
results, Scan Tool functions and Monitor status information. See
DISPLAY FUNCTIONS (page 9) for more details.
14. CABLE - Connects the Scan Tool to the vehicle’s Data Link
Connector (DLC).
DISPLAY FUNCTIONS
2
1
15 14
3
4
5
10
11
6
12
7
8
9
13
Figure 2. Display Functions
See Figure 2 for the locations of items 1 through 15, below.
3
Scan Tool Controls
DISPLAY FUNCTIONS
1. I/M MONITOR STATUS field - Identifies the I/M Monitor status area.
2. Monitor icons - Indicate which Monitors are supported by the vehicle
under test, and whether or not the associated Monitor has run its
diagnostic testing (Monitor status). A solid green icon indicates the
associated Monitor has completed its diagnostic testing. A flashing red
icon indicates that the vehicle supports the associated Monitor, but the
Monitor has not yet run its diagnostic testing.
3.
Vehicle icon - When visible, indicates that the Scan Tool is
being powered through the vehicle’s DLC connector.
4.
Link icon - When visible, indicates the Scan Tool is
communicating with the vehicle’s computer.
5.
Computer icon - When visible, indicates the Scan Tool is linked
to a personal computer.
6. DTC Display Area - Displays the Diagnostic Trouble Code (DTC)
number. Each fault is assigned a code number that is specific to that
fault. The DTC number is color-coded as follows:
„
RED - Indicates the currently displayed DTC is a STORED OR
PERMANENT DTC.
„
YELLOW - Indicates the currently displayed DTC is a PENDING
DTC.
„
GREEN - In cases where no codes are retrieved, a “No DTCs
are presently stored in the vehicle’s computer” message is
shown in green.
7. Code Number Sequence - The Scan Tool assigns a sequence
number to each DTC that is present in the computer’s memory,
starting with “1.” This number indicates which code is currently
displayed. Code number “1” is always the highest priority code, and
the one for which “Freeze Frame” data has been stored.
If “1” is a “Pending” code, there may or may not be “Freeze
Frame” data stored in memory.
8. Code Enumerator - Indicates the total number of codes retrieved
from the vehicle’s computer.
9. Test Data Display Area - Displays DTC definitions, Freeze Frame
data and other pertinent test information messages.
10. SYSTEM icon - Indicates the system with which the code is
associated:
MIL icon
ABS icon
SRS icon
11. FREEZE FRAME icon - Indicates that there is Freeze Frame data
from “Priority Code” (Code #1) stored in the vehicle’s computer
memory.
12. Code type - Indicates the type of code being displayed; Generic
Stored, Generic Pending, Generic permanent, etc.
13. Severity - Indicates the level of severity for the priority code (code
number “1”), as follows:
4
Scan Tool Controls
INITIAL ADJUSTMENTS
1 - Service should be scheduled and repairs made when
convenient. This DTC typically has no immediate threat to
essential system components in the short term.
2 - Repair immediately if drivability issues are present. Threat to
essential system components if not repaired as soon as possible.
3 - Stop and repair vehicle immediately to prevent interrelated
failures. Harmful and damaging to essential system components.
14.
Bluetooth icon – Indicates communication status with a compatible
Innova mobile application (please visit www.innova.com/apps for more
information). A solid blue icon indicates an active Bluetooth connection
has been established. A solid grey icon indicates Bluetooth is not
connected.
15.
Wi-Fi icon – Indicates Wi-Fi communication status. When ON,
indicates the scan tool is linked to a Wi-Fi network. When OFF,
indicates there is no Wi-Fi connection.
INITIAL ADJUSTMENTS
The first time the unit is connected to a vehicle, you must select the
desired display language (English, French or Spanish) and unit of
measurement (Standard or metric) as follows:
1. Select the desired display language, then press ENTER
„
.
The Select Unit screen displays.
2. Select the desired unit of measurement, then press ENTER
.
After the initial language and unit of measurement selections
are performed, these, as well as other settings, can be
changed as desired. Proceed to “ADJUSTMENTS AND
SETTINGS” on page 40 for further instructions.
5
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
CODE RETRIEVAL PROCEDURE
Retrieving and using Diagnostic Trouble Codes (DTCs) for
troubleshooting vehicle operation is only one part of an
overall diagnostic strategy.
Never replace a part based only on the DTC definition.
Each DTC has a set of testing procedures, instructions and
flow charts that must be followed to confirm the location of
the problem. Always refer to the vehicle's service manual
for detailed testing instructions.
Check your vehicle thoroughly before performing
any test.
ALWAYS observe safety precautions whenever working on a
vehicle.
3. Turn the ignition off.
4. Locate the vehicle's 16-pin Data Link
Connector (DLC).
Some DLCs have a plastic cover
that must be removed before
connecting the Scan Tool cable
connector.
If the Scan Tool is ON, turn it OFF
BEFORE connecting the Scan
Tool to the DLC.
5. Connect the Scan Tool to the vehicle’s DLC. The cable connector is
keyed and will only fit one way.
„
If you have problems connecting the cable connector to the DLC,
rotate the connector 180°.
„
If you still have problems, check the DLC on the vehicle and on
the Scan Tool.
6. Turn the ignition on. DO NOT start the engine.
7. When the Scan Tool is properly connected to the vehicle’s DLC, the
unit automatically turns ON.
6
„
If the unit does not power on automatically, it may indicate there
is no power present at the vehicle’s DLC connector. Check the
fuse panel and replace any burned-out fuses.
„
If replacing the fuse(s) does not correct the problem, consult
your vehicle’s repair manual to identify the proper computer
(PCM) fuse/circuit, and perform any necessary repairs before
proceeding.
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
8. The Scan Tool automatically starts a check of the vehicle’s
computer to determine which type of communication protocol it is
using. When the Scan Tool identifies the computer’s communication
protocol, a communication link is established.
A PROTOCOL is a set of rules and procedures for regulating
data transmission between computers, and between testing
equipment and computers. As of this writing, five different
types of protocols (ISO 9141, Keyword 2000, J1850 PWM,
J1850 VPW and CAN) are in use by vehicle manufacturers.
„
If the Scan Tool fails to link to the vehicle’s computer, a
“Communication Error” message shows.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
„
to continue.
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press the SYSTEM MENU
Menu.
- Turn the ignition off,
disconnect the Scan Tool.
button to return to the System
and
- Contact Technical Support for
assistance.
9. If the Scan Tool can decode the Vehicle
Identification Number (VIN) for the
vehicle under test, the Confirm Vehicle
screen displays.
„
If the information shown is correct for the vehicle under test,
select Yes, then press ENTER
. Proceed to step 10.
„
If the information shown is not correct for the vehicle under test,
or if you wish to manually select the vehicle, select No, then
press ENTER
. Proceed to step 8.
„
If the Scan Tool cannot decode the Vehicle Identification
Number (VIN) for the vehicle under test, the Select Vehicle
screen displays. Proceed to step 8.
10. When No is selected from the Vehicle
information screen, the Select Vehicle
screen displays. The Select Vehicle
screen lists the three most recently
tested vehicles.
7
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
„
To select a previously tested vehicle, select the desired vehicle,
then press ENTER
. Proceed to step 10.
„
To select a new vehicle, select New
Vehicle, then press ENTER
.
Proceed to step 9.
11. When New Vehicle is chosen from the
Select Vehicle screen, the Select Year
screen displays.
„
Select the desired vehicle model
year, then press ENTER
to
continue.
-
„
Select the desired vehicle make,
then press ENTER
to continue.
-
„
The Select
displays.
Model
screen
Select the desired vehicle model,
then press ENTER
to continue.
-
„
The Select Make screen displays.
The Select
displays.
Engine
screen
Select the desired vehicle engine
size, then press ENTER
to
continue.
-
The Select Transmission screen
displays.
„
Select the desired transmission type,
then press ENTER
to continue.
The Vehicle Information screen
displays.
„
If the information shown is correct
for the vehicle under test, select
Yes, then press ENTER
.
Proceed to step 10.
„
If the information shown is not correct for the vehicle under test,
or if you wish to reselect the vehicle, select No, then press
ENTER
to return to the Select Year screen.
12. After approximately 10~60 seconds, the Scan Tool will retrieve and
display any Diagnostic Trouble Codes, Monitor Status and Freeze
Frame Data retrieved from the vehicle’s computer memory.
„
8
The Scan Tool will display a code only if codes are present. If no
codes are present, the message “No Powertrain DTCs or Freeze
Frame Data presently stored in the vehicle’s computer” displays.
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
„
The Scan Tool is capable of retrieving and storing up to 32
codes in memory, for immediate or later viewing.
13. Refer to DISPLAY FUNCTIONS on page 3 for a description of
display elements.
In the case of long code definitions,
a small arrow is shown in the
upper/lower right-hand corner of the
Scan Tool display area to indicate
the
presence
of
additional
information.
If a definition for the currently
displayed code is not available,
an advisory message shows on
the Scan Tool’s display.
14. Read and interpret Diagnostic Trouble Codes/system condition
using the display and the green, yellow and red LEDs.
The green, yellow and red LEDs are used (with the display) as
visual aids to make it easier to determine engine system
conditions.
„
Green LED – Indicates that all engine
systems are “OK” and operating
normally. All monitors supported by
the vehicle have run and performed
their diagnostic testing, and no trouble
codes are present. All Monitor icons
will be solid.
„
Yellow LED – Indicates one of the
following conditions:
A. A PENDING CODE IS PRESENT – If
the yellow LED is illuminated, it may
indicate a Pending code is present.
Check the display for confirmation. A
Pending code is confirmed by the
presence of a numeric code and the
word PENDING.
B. MONITOR NOT RUN STATUS – If
the display shows a zero (indicating
there are no DTC’s present in the
vehicle’s computer memory), but the
yellow LED is illuminated, it may be
an indication that some of the
Monitors supported by the vehicle
have not yet run and completed their
diagnostic testing. Check the display
for confirmation. All Monitor icons that
are blinking have not yet run and
completed their diagnostic testing; all
Monitor icons that are solid have run
and completed their diagnostic testing.
9
Using the Scan Tool
CODE RETRIEVAL PROCEDURE
„
Red LED – Indicates there is a
problem with one or more of the
vehicle’s systems. The red LED is
also used to indicate that DTC(s)
are present. In this case, the
Malfunction Indicator (Check Engine)
lamp on the vehicle’s instrument
panel will be illuminated.
„
DTC’s that start with “P0”, “P2” and
some “P3” are considered Generic
(Universal). All Generic DTC definitions are the same on all OBD2
equipped vehicles. The Scan Tool automatically displays the code
definitions (if available) for Generic DTC’s.
„
DTC’s that start with “P1” and some “P3” are Manufacturer specific
codes and their code definitions vary with each vehicle manufacturer.
15. If more than one DTC was retrieved, and to view Freeze Frame
Data, press and release DTC/FF as necessary.
„
Each time DTC/FF is pressed and released, the Scan Tool will
scroll and display the next DTC in sequence until all DTCs in its
memory have displayed.
„ Freeze Frame Data (if available) will display after DTC #1.
„ In
OBD2 systems, when an
emissions-related engine malfunction
occurs that causes a DTC to set, a
record or snapshot of engine conditions at the time that the malfunction
occurred is also saved in the vehicle’s
computer memory. The record saved
is called Freeze Frame data. Saved
engine conditions include, but are not
limited to: engine speed, open or closed loop operation, fuel system
commands, coolant temperature, calculated load value, fuel
pressure, vehicle speed, air flow rate, and intake manifold pressure.
If more than one malfunction is present that causes more than
one DTC to be set, only the code with the highest priority will
contain Freeze Frame data. The code designated “01” on the
Scan Tool display is referred to as the PRIORITY code, and
Freeze Frame data always refers to this code. The priority
code is also the one that has commanded the MIL on.
16. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” Code.
17. Determine engine system(s) condition by viewing the Scan Tool’s
display for any retrieved Diagnostic Trouble Codes, code definitions and
Freeze Frame data, interpreting the green, yellow and red LEDs.
„ If DTC’s were retrieved and you are going to perform the repairs
yourself, proceed by consulting the Vehicle’s Service Repair
Manual for testing instructions, testing procedures, and flow
charts related to retrieved code(s).
10
Using the Diagnostic Tool
THE SYSTEM MENU - VIEWING OEM ENHANCED DTCs (except Ford/Mazda)
THE SYSTEM MENU
The System Menu provides the ability to retrieve “enhanced” DTCs and
Anti-Lock Brake System (ABS) DTCs for most BMW, Chrysler/Jeep,
Ford/Mazda, GM/Isuzu, Honda/Acura, Hyundai, Mercedes Benz, Nissan,
Toyota/Lexus, Volkswagen and Volvo vehicles. The types of enhanced
data available depends on the vehicle make. You can also return to the
Global OBD2 mode.
Depending on the vehicle under test, some features and functions
may not be available.
„
To access the System Menu, press
. Select the desired
SYSTEM MENU
option, then press ENTER
to view
the selected information.
To view ABS DTCs: Select ABS from the System Menu. Refer to
VIEWING ABS DTCs on page 14 to view ABS DTCs for your vehicle.
To view SRS DTCs: Select SRS from the System Menu. Refer to
VIEWING SRS DTCs on page 15 to view SRS DTCs for your vehicle.
To view OEM enhanced DTCs: Select OEM Enhanced from the
System Menu. Refer to VIEWING OEM ENHANCED DTCs on page 11
to view OEM enhanced DTCs for your vehicle.
VIEWING OEM ENHANCED DTCs (except Ford/Mazda)
When (make) OEM Enhanced is chosen from the System Menu, the
Scan Tool retrieves OEM enhanced DTCs from the vehicle’s computer.
1. A “One moment please” message displays while the Scan Tool
retrieves the selected DTCs.
„
If the Scan Tool fails to link to the vehicle’s computer, a
“Communication Error” message shows.
Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
„
to continue.
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press SYSTEM MENU
to return to the System Menu.
- Turn the ignition off, and disconnect the Scan Tool.
- Contact Technical Support for assistance.
2. Refer to DISPLAY FUNCTIONS on page 3 for a description of LCD
display elements.
11
Using the Diagnostic Tool
VIEWING OEM ENHANCED DTCs (Ford/Mazda only)
If the definition for the currently displayed code is not
available, an advisory message shows.
I/M MONITOR STATUS
icons are not displayed
when viewing enhanced
DTCs.
In the case of long code definitions, a small arrow is
shown in the upper/lower right-hand corner of the code
display area to indicate the presence of additional
information.
„
If no codes are present, the message “No OEM Enhanced DTC’s
are presently stored in the vehicle’s computer” shows. Press
to return to the System Menu.
SYSTEM MENU
3. If more than one code was retrieved press DTC/FF, as necessary,
to display additional codes one at a time.
„
Whenever the Scroll function is used to view additional codes,
the Scan Tool’s communication link with the vehicle’s computer
disconnects. To re-establish communication, press LINK
again.
4. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” Code.
„
To exit the enhanced mode, press SYSTEM MENU
to return
to the System Menu. Select Global OBD, then press ENTER
to return to the Global OBD2 mode.
VIEWING OEM ENHANCED DTCs (Ford/Mazda only)
Mazda Enhanced DTCs are available for Mazda-branded
Ford vehicles only.
When Ford OEM Enhanced is chosen from
the System Menu, the Ford Enhanced
menu displays. You may view OEM DTCs
for either the “Continuous Memory Test”,
“KOEO (Key On Engine Off) Test” or
“KOER (Key On Engine Running) Test.”
5. Select the desired option, then press
ENTER
.
„
If KOER is selected, an advisory message shows.
- Start and warm the engine to normal operating temperature,
then press ENTER
. Proceed to step 3.
6. If KOEO or Continuous Memory is selected, an “instructional”
message shows.
„
12
Turn the ignition OFF, then back ON. Press ENTER
Proceed to step 3.
.
Using the Scan Tool
VIEWING OEM ENHANCED DTCs
7. A “One moment please” message displays while the test is in
progress.
„ If the Scan Tool fails to link to the vehicle’s computer, a
“Communication Error” message shows.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
„
- Press LINK
to continue.
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press SYSTEM MENU
to return to the System Menu.
- Turn the ignition off, and disconnect the Scan Tool.
„
„
- Contact Technical Support for assistance.
If the KOER Test was selected, and the vehicle’s engine is not
running, an advisory message shows.
- Start the engine and press ENTER
to try again, or, press
to return to the System Menu.
SYSTEM MENU
If the KOEO Test was selected, and the vehicle’s engine is
running, an advisory message shows.
- Turn the ignition OFF then back ON and press ENTER
to
to return to the System
try again, or, press SYSTEM MENU
Menu.
8. If the KOER test was selected, an “instructional” message shows.
„
Turn the steering wheel to the left, then release.
„
Press and release the brake pedal.
„
Cycle the overdrive switch (if equipped).
„
A “One moment please” message displays while the test is in
progress.
9. Refer to DISPLAY FUNCTIONS on page 3 for a description of LCD
display elements.
I/M MONITOR STATUS icons
are not displayed when
viewing enhanced DTCs.
In the case of long code
definitions, a small arrow is
shown in the upper/ lower righthand corner of the code display
area to indicate the presence
of additional information.
13
Using the Diagnostic Tool
VIEWING ABS DTCs
„
If no codes are present, a “System
Pass” message displays. Press any
Hotkey.
10. If more than one code was retrieved
press DTC/FF to display additional
codes one at a time.
11. When the last retrieved DTC has been
displayed and DTC/FF is pressed, the
Scan Tool returns to the “Priority” Code.
„
To view additional enhanced DTCs, repeat steps 1 through 5,
above.
„
To exit the enhanced mode, press SYSTEM MENU
to return
to the System Menu. Select Global OBD, then press ENTER
to return to the Global OBD2 mode.
VIEWING ABS DTCs
Refer to the manufacturer’s website for vehicle makes covered.
Reading ABS DTCs
1. When ABS is chosen from the System Menu, a "One moment
please" message displays while the Scan Tool retrieves the selected
DTCs.
„
If ABS functionality is not supported, an advisory message
to return to the System Menu.
shows. Press SYSTEM MENU
„
If the Scan Tool fails to link to the vehicle’s computer, a
"Communication Error" message shows.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
„
to continue.
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press SYSTEM MENU
to return to the System Menu.
- Turn the ignition off, and disconnect the Scan Tool.
- Contact Technical Support for assistance.
2. Refer to DISPLAY FUNCTIONS on page 3 for a description of LCD
display elements.
14
Using the Scan Tool
VIEWING SRS DTCs
If the definition for the currently
displayed code is not available, an
advisory message shows.
I/M MONITOR STATUS icons are
not displayed when viewing ABS
DTCs.
In the case of long code definitions, a small arrow is shown in
the upper/lower right-hand corner of the code display area to
indicate the presence of additional information.
„
If no codes are present, the message "No ABS DTC’s are
presently stored in the vehicle’s computer" shows. Press
to return to the System Menu.
SYSTEM MENU
3. If more than one code was retrieved press DTC/FF to display
additional codes one at a time.
„
Whenever the Scroll function is used to view additional codes,
the Scan Tool’s communication link with the vehicle’s computer
disconnects. To re-establish communication, press LINK
again.
4. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” Code.
„
To exit the enhanced mode, press SYSTEM MENU
to return
to the System Menu. Select Global OBD, then press ENTER
to return to the Global OBD2 mode.
VIEWING SRS DTCs
Refer to the manufacturer’s website for vehicle makes covered.
Reading SRS DTCs
1. When SRS is chosen from the System Menu, a "One moment
please" message displays while the Scan Tool retrieves the selected
DTCs.
„
If SRS functionality is not supported, an advisory message
to return to the System Menu.
shows. Press SYSTEM MENU
„
If the Scan Tool fails to link to the vehicle’s computer, a
"Communication Error" message shows.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
to continue.
15
Using the Scan Tool
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
„
If the Scan Tool cannot link to the vehicle’s computer after three
attempts, the message “Contact Technical Support” displays.
- Press SYSTEM MENU
to return to the System Menu.
- Turn the ignition off, and disconnect the Scan Tool.
- Contact Technical Support for assistance.
2. Refer to DISPLAY FUNCTIONS on page 3 for a description of LCD
display elements.
If the definition for the currently
displayed code is not available, an
advisory message shows
I/M MONITOR STATUS icons are
not displayed when viewing SRS
DTCs.
In the case of long code definitions, a small arrow is shown in
the upper/lower right-hand corner of the code display area to
indicate the presence of additional information.
„
If no codes are present, the message "No SRS DTC’s are
presently stored in the vehicle’s computer" shows. Press
to return to the System Menu.
SYSTEM MENU
3. If more than one code was retrieved press DTC to display additional
codes one at a time.
„ Whenever the Scroll function is used to view additional codes,
the Scan Tool’s communication link with the vehicle’s computer
disconnects. To re-establish communication, press LINK
again.
4. When the last retrieved DTC has been displayed and DTC/FF is
pressed, the Scan Tool returns to the “Priority” code.
„
To exit the enhanced mode, press SYSTEM MENU
to return
to the System Menu. Select Global OBD, then press ENTER
to return to the Global OBD2 mode.
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
When the Scan Tool’s ERASE function is used to erase DTCs
from the vehicle's on-board computer, "Freeze Frame" data
and manufacturer-specific-enhanced data are also erased.
"Permanent" DTCs ARE NOT erased by the ERASE function.
If you plan to take the vehicle to a Service Center for repair, DO NOT
erase the codes from the vehicle's computer. If the codes are erased,
valuable information that might help the technician troubleshoot the
problem will also be erased.
Erase DTCs from the computer's memory as follows:
16
Using the Scan Tool
ERASING DIAGNOSTIC TROUBLE CODES (DTCs)
When DTCs are erased, the I/M Readiness Monitor Status
program resets the status of all Monitors to a not run condition. To
set all Monitors to a DONE status, an OBD2 Drive Cycle must be
performed.
1. If not connected already, connect the
Scan Tool to the vehicle's DLC, and
turn the ignition "On.” (If the Scan Tool
is already connected and linked to the
vehicle's computer, proceed directly to
step 3. If not, continue to step 2.)
2. Perform the Code Retrieval procedure
as described on page 6.
„
To erase OBD2 DTCs: Wait until
the codes are displayed, then
proceed to step 3.
„
To erase enhanced, ABS or SRS
to display the System Menu.
DTCs: Press SYSTEM MENU
Select the desired option, then press ENTER
. Perform the
appropriate Code Retrieval procedure and then proceed to step 3.
3. Press and release ERASE
confirmation message shows.
. A
„
If you are sure you want to proceed,
select Yes, then press ENTER
.
„
If you do not want to proceed, select
No, then press ENTER
to
cancel the erase procedure.
4. If you chose to erase DTCs, a “One moment please…” message
displays while the erase function is in progress.
If the vehicle’s engine is running, an advisory message shows.
Turn the engine OFF, then turn the ignition back to ON. DO
NOT start the engine. Press ENTER
to continue.
„
If the erase was successful, a
confirmation message shows. The
Scan Tool automatically relinks to the
vehicle’s computer after 3 seconds.
If the erase was not successful and
ECU error code $22 is present, an
advisory message displays. Start
the engine and maintain vehicle
to try again.
speed at 0, then press ERASE
„
If the erase was not successful, an advisory message shows
indicating the erase request was sent to the vehicle’s computer.
The Scan Tool automatically relinks to the vehicle’s computer
after 3 seconds.
17
Using the Scan Tool
ABOUT REPAIRSOLUTIONS®
Erasing DTCs does not fix the problem(s) that caused the
code(s) to be set. If proper repairs to correct the problem that
caused the code(s) to be set are not made, the code(s) will
appear again (and the Check Engine Light will illuminate) as
soon as the vehicle is driven long enough for its Monitors to
complete their testing.
ABOUT REPAIRSOLUTIONS®
RepairSolutions 2® is a web-based service created to assist both Do-ItYourself and Professional technicians in quickly and accurately
diagnosing and repairing today’s vehicles. RepairSolutions 2 allows you
to view and save the diagnostic data retrieved from a vehicle’s on-board
computer(s) using your Code Reader. At the core of RepairSolutions 2
is an extensive knowledge database, developed by compiling and
analyzing years worth of “real world” vehicle service data.
RepairSolutions 2 builds on manufacturer-recommended diagnostic and
repair information by providing verified, vehicle-specific fixes supplied by
ASE technicians across the country. RepairSolutions 2 also provides
access to an extensive knowledge database including:
„
Verified Fixes – Find the most likely fixes reported and verified by
ASE Technicians for the retrieved DTCs.
„
Repair Instructions – View available repair instructions to properly
perform the fix.
„
Video Tutorials – Watch repair video tutorials for valuable repair
tips.
„
Technical Service Bulletins – Research known problems reported
by vehicle manufacturers.
„
Safety Recalls – Research known safety concerns applicable to a
vehicle.
And much more. Please visit www.innova.com for additional information.
Hardware Requirements:
„
Innova Scan Tool with Bluetooth/WiFi
„
Android or iOS Smart Device
Accessing RepairSolutions 2®
1. Download and install the RepairSolutions 2® app from the App
Store (for iOS devices) or Google Play (for Android devices).
2. Launch the RepairSolutions 2 app and log in to your account.
18
„
If you have not yet established an account, you must register for
a FREE RepairSolutions 2 account before proceeding.
„
Connect the Code Reader to a vehicle and establish a Bluetooth
or WiFi connection with your Smart Device (refer to
CONNECTING TO BLUETOOTH / WIFI, below). Be sure your
Smart Device is connected to an available WiFi network.
Using the Scan Tool
CONNECTING TO BLUETOOTH / WIFI
„
The RepairSolutions 2 app will store two WiFi configurations
only.
3. Retrieve diagnostic data (refer to CODE RETRIEVAL PROCEDURE
on page 6 for details).
4. The RepairSolutions 2 app automatically displays a report based on
the retrieved diagnostic data.
„
If the Code Reader is not connected to WiFi or Bluetooth,
vehicle data will not be saved.
CONNECTING TO BLUETOOTH / WIFI
Launch the RepairSolutions 2 app and follow the prompts to
establish Bluetooth and (optionally) WiFi connections, as follows:
1. Launch the RepairSolutions 2 app. Select Wifi Tools Settings
from the menu. Power on your Code Reader, then select from the
list of available devices.
2. When Bluetooth pairing is complete, a confirmation screen displays.
Click Continue.
„
If a Bluetooth connection cannot be established, an advisory
message displays. Tap Try Again to repeat the pairing process.
3. Follow the on-screen prompts to connect to an available WiFi
network.
„
You can automatically connect to the network your Smart Device
is currently connected to, or you can manually connect to
another available network.
„
Note that only 2.4GHz networks are supported.
„
If you do not wish to connect to a WiFi network at this time, tap
SKIP.
4. When WiFi pairing is complete, a confirmation screen displays. Click
Continue to view the “Setup Complete” message, then click
Continue to enter RepairSolutions 2.
„
If a WiFi connection cannot be established, an advisory
message displays. Tap Try Again to repeat the pairing process.
19
Live Data Mode
VIEWING LIVE DATA
The Scan Tool lets you view "real-time" Live Data. This information
includes values (volts, rpm, temperature, speed etc.) and system status
information (open loop, closed loop, fuel system status, etc.) generated by
the various vehicle sensors, switches and actuators. These are the same
signal values generated by the sensors, actuators, switches and/or
vehicle system status information used by the vehicle's computer when
calculating and conducting system adjustments and corrections.
The real time (Live Data) vehicle operating information (values/status)
that the computer supplies to the Scan Tool for each sensor, actuator,
switch, etc. is called Parameter Identification (PID) Data.
Each PID (sensor, actuator switch, status, etc.) has a set of operating
characteristics and features (parameters) that serve to identify it. The
Scan Tool displays this information for each sensor, actuator, switch or
status that is supported by the vehicle under test.
WARNING: If the vehicle must be driven in order to perform a
troubleshooting procedure, ALWAYS have a second person
help you. One person should drive the vehicle while the other
person observes the Scan Tool data. Trying to drive and
operate the Scan Tool at the same time is dangerous, and
could cause a serious traffic accident.
VIEWING LIVE DATA
1. While linked to the vehicle, start the engine, then press LD.
2. A “One moment please . . .” message displays while the Scan Tool
establishes communication with the vehicle.
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2
compliant.
- Verify the connection at the DLC,
and verify the ignition is ON.
- Turn the ignition OFF, wait 5
seconds, then back ON to reset
the computer.
- Press ENTER
to continue.
3. Real-time Live Data (PID) information supported by the vehicle
under test displays.
„
If Live Data is not supported by the vehicle under test, an
to return
advisory message displays. Press SYSTEM MENU
to the System Menu. Live Data is not available for your vehicle.
The values for the various PIDS displayed may change as the
vehicle's operating conditions change.
4. Only a limited amount of PID data can be displayed on the screen at
one time. If additional PID data is available, a small arrow is shown
and DOWN
, as necessary, to view
on the display. Press UP
all available PID data.
20
Live Data Mode
CUSTOMIZING LIVE DATA (PIDs)
„
If communication with the vehicle is
lost while viewing Live Data, an
advisory message displays.
5. Press and release ENTER
to view
the currently selected PID in “graph” mode.
Press and release ENTER
again to
return to the PID list.
„
You can display a maximum of two
PIDs in "graph" mode at any given
time.
„
With two PID shown in "graph"
mode, press and hold LD to
superimpose one graph on the other.
Release LD to separate the graphs.
6. Press and hold ENTER
to view the
“expanded” definition for the currently
selected PID. Release to return to the PID
list.
7. If you experience vehicle problems,
view and/or compare the Live Data (PID)
information displayed on the Scan Tool
to specifications in the vehicle's repair
manual.
If desired, you can "customize" the Live Data display to show only
those PIDs you are interested in viewing. See Customizing Live
Data (PIDs) below for details.
CUSTOMIZING LIVE DATA (PIDs)
You can customize the Live Data display by placing the Scan Tool in
"Custom Live Data" mode and selecting only the PIDs that you wish to
display.
1. With the Scan Tool in Live Data mode
(see VIEWING LIVE DATA on page 20),
press and hold LD until the Live Data
Menu displays, then release
2. Select Custom Live Data, then press
ENTER
.
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
to continue.
21
Live Data Mode
RECORDING (CAPTURING) LIVE DATA
„
If Live Data is not supported by the vehicle under test, an
to return
advisory message displays. Press SYSTEM MENU
to the System Menu.
„
If custom Live Data was previously configured, the Select PIDs
to Use screen displays.
- To use the existing custom Live data selections, select Use
. Proceed to step 5.
existing PIDs, then press ENTER
- To configure new custom Live Data, select Select new PIDs,
then press ENTER
. The Custom Live Data menu displays.
Proceed to step 3.
„
If custom Live Data was not previously selected, the Custom
Live Data menu displays. Proceed to step 3.
and DOWN
to scroll
3. Press UP
through the available PIDs. When a PID
you wish to display is highlighted, press
ENTER
(a "checkmark" shows to
confirm your selection). Repeat until only
the PIDs you want to display are selected.
„
To deselect a PID, highlight the PID,
then press ENTER
. The
checkmark is removed.
4. When you are finished making your selection(s), press LD to
continue.
„
If no PIDs have been selected, an advisory message displays.
Press ENTER
to return to the Custom Live Data menu.
5. The Scan Tool is now in "Custom Live Data" mode. Only the PIDs
you selected are shown.
„
To change the current custom Live
Data selections, select Reselect
PIDs, then press ENTER
to
return to the Custom Live Data
menu. Repeat step 3.
6. To exit the "Custom Live Data" mode,
press LD to return to the Live Data Menu.
RECORDING (CAPTURING) LIVE DATA
You can record and save several frames of Live Data information for
each PID supported by the vehicle in the Scan Tool's memory.
There are two ways that the Scan Tool can record Live Data:
22
„
Record by DTC Trigger
„
Record by Manual Trigger
Live Data Mode
RECORDING (CAPTURING) LIVE DATA
If LINK
is pressed at any time while in Live Data mode,
any recorded Live Data will be erased from the Scan Tool’s
memory.
Record by DTC Trigger
This function automatically records Live Data information when a DTC
sets and saves it in the Scan Tool’s memory. The recorded (captured)
data can be a valuable troubleshooting aid, particularly if you are
experiencing a fault that is causing a DTC to set. The Scan Tool can
record approximately 100 frames of Live Data.
1. With the Scan Tool in Live Data mode (see VIEWING LIVE DATA
on page 20), press and hold the LD button until the Live Data Menu
displays, then release the LD button.
2. Select Record Live Data, then press ENTER
.
„
The Record Live Data Menu displays.
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
to continue.
3. Select Record by DTC Trigger, then press ENTER
„
.
The Select PIDs to Record screen
displays.
4. Press UP
and DOWN
to scroll
through the available PIDs. When a PID
you wish to record is highlighted, press
ENTER
(a “checkmark” shows to
confirm your selection). Repeat the
procedure until only the PIDs you want
to record are selected.
„
To deselect a currently selected PID, highlight the PID, then
press ENTER
. The checkmark is removed.
To record all PIDs, select Record All PIDs, the press LD to
continue.
5. When you are finished making your selections, press LD to continue.
„
If DTCs are presently stored in the
vehicle’s computer, an advisory
message displays. Select Erase
DTCs, then press ENTER
. A
“One moment please…” message
displays while DTCs are erased
from the vehicle’s computer.
23
Live Data Mode
RECORDING (CAPTURING) LIVE DATA
„
If the erase was not successful, an
advisory message displays.
- To retry the erase process, verify
that the Scan Tool is properly
connected to the vehicle’s DLC
and that the ignition is on. Select
Erase, then press ENTER
.
- To exit the record function, select
Back, then press ENTER
to
return to the Record Live Data
menu.
6. Put the engine in the operating
condition that causes the DTC to set.
„
If necessary, drive the vehicle until
you reach the vehicle speed at
which the problem occurs.
7. When the Scan Tool detects a fault that
causes a DTC to set, it automatically
records and saves approximately 100
frames of Live Data information in its
memory for each PID selected.
„
A progress message shows on the
display.
- You can stop and save recorded Live Data at any time by
.
pressing ENTER
„
When recording is complete, a confirmation screen displays.
Select Yes and press ENTER
to playback Live Data (see
LIVE DATA PLAYBACK on page 26 for details) or select No and
press ENTER
to return to the Live Data menu, as desired.
„
If recording was not successful, an advisory message displays.
to return to the Record Live Data menu.
Press ENTER
Record by Manual Trigger
This option lets you select the precise time at which the Live Data recording
will occur. Record by Manual Trigger can be a very valuable tool when
troubleshooting intermittent problems that do not meet the requirements for
a DTC to set. The Scan Tool can record approximately 100 frames of Live
Data.
1. With the Scan Tool in Live Data mode (see VIEWING LIVE DATA
on page 20), press and hold LD until the Live Data Menu displays,
then release.
2. Select Record Live Data, then press ENTER
„
24
The Record Live Data Menu displays.
.
Live Data Mode
RECORDING (CAPTURING) LIVE DATA
„
If the Scan Tool fails to establish communication with the vehicle,
a “Communication Error” message displays.
- Ensure your vehicle is OBD2 compliant.
- Verify the connection at the DLC, and verify the ignition is ON.
- Turn the ignition OFF, wait 5 seconds, then back ON to reset
the computer.
- Press LINK
to continue.
3. Select Record Manually, then press ENTER
„
.
The Select PIDs to Record screen
displays.
and DOWN
to scroll
4. Press UP
through the available PIDs. When a PID
you wish to record is highlighted, press
ENTER
(a “checkmark” shows to
confirm your selection). Repeat until
only the PIDs you want to record have
all been selected.
„
To deselect a PID, highlight the PID, then press ENTER
The checkmark is removed.
.
To record all PIDs, select Record All PIDs, the press LD to
continue.
5. When you are finished making your
selections, press LD to continue.
„
The Record
displays.
„
Highlight Start Recording. Put the
engine in the operating condition
where the problem manifests itself.
Live
Data
screen
- If necessary, drive the vehicle until you reach the vehicle
speed at which the problem occurs.
6. When the problem occurs, press and
release LD.
„ A progress message shows on the
display.
- You can stop and save recorded
Live Data at any time by pressing
ENTER
.
„
When recording is complete, a confirmation screen displays.
Select Yes and press ENTER
to playback Live Data (see
LIVE DATA PLAYBACK on page 26 for details) or select No and
press ENTER
to return to the Live Data menu, as desired.
„
If recording was not successful, an advisory message displays.
to return to the Record Live Data menu.
Press ENTER
25
Live Data Mode
LIVE DATA PLAYBACK
LIVE DATA PLAYBACK
Once Live Data has been recorded, it is saved in the Scan Tool's
memory. You can view recorded Live Data immediately after recording
by selecting Yes from the Record Live Data confirmation screen (see
RECORDING (CAPTURING) LIVE DATA on page 22 for more
information), or you can view it later using the "Playback" function.
1. With the Scan Tool connected to the vehicle and in Live Data mode
(see VIEWING LIVE DATA on page 20), press and hold LD until the
Live Data Menu displays, then release.
2. Select Playback Live Data, then press ENTER
„
.
The Playback Live Data menu displays.
When you select Yes from the Record Live Data confirmation
screen, the Scan Tool enters the "Live Data Playback" mode,
and the Playback Live Data menu displays.
3. Select Continuous Playback or Frame by Frame, as desired, then
press ENTER
.
„
Only a limited amount of PID data
can be displayed on the screen at
one time. If additional PID data is
available, a small arrow is shown on
and
the display. Press UP
DOWN
, as necessary, to view
all available PID data.
„
When viewing recorded Live Data, look for any irregularities in
any of the PID values/signal information (LTFT %, RPM, MAP,
TEMP, etc.). If any PIDs are not within specification, or
irregularities are detected, follow the procedures in the vehicle's
service repair manual to perform additional troubleshooting and
repair.
4. When you select Continuous Playback,
the Scan Tool plays recorded data at a
rate of one frame / 15 seconds. When
playback is finished, a Playback
Complete message displays.
„
To play the data back again, select
Continuous Playback or Frame by
Frame, as desired, then press
ENTER
.
„
To exit Live Data Playback mode and return to Live Data mode,
select Exit Playback, then press ENTER
.
5. When Frame by Frame is selected, you must scroll the individual
frames manually.
„
26
When you have viewed all PID information for the current frame
of Live Data, select Next Frame or Previous Frame, as desired,
then press ENTER
.
Live Data Mode
LIVE DATA PLAYBACK
„
To exit Live Data Playback mode, select Exit Playback, then
.
press ENTER
If there is no Live Data currently stored in the Scan Tool's
memory, an advisory message shows on the display. Press
LD to exit the "Live Data Playback" mode.
27
Additional Tests
SYSTEM TEST MENU
In addition to retrieving Diagnostic Trouble Codes (DTCs), you can use
the Scan Tool to perform additional diagnostic tests, to view diagnostic
and vehicle information stored in your vehicle's on-board computer, and
to configure the Scan Tool for your particular needs. Additional tests and
related functions are accessed through the Main Menu. The following
functions are available:
„
System Tests – Displays the System
Test menu, which lets your retrieve and
view results for the O2 Sensor Test and
OBD Monitor Test, and lets you initiate
a test of the vehicle’s EVAP system.
„
Service Reset – Lets you reset the Oil
Maintenance Light.
„
Service Check – Lets you view the
current engine oil level and oil life
remaining.
„
Battery/Alternator Test – Performs a check of the vehicle’s battery
and alternator system to ensure the system is operating within
acceptable limits.
„
DLC Locator – Lets you find the location of the Data Link
Connector (DLC) for a specified vehicle.
„
Vehicle Information – Displays the Vehicle Info menu, which lets
you retrieve and view reference information for the vehicle under
test.
„
Firmware Version – Displays the Scan Tool’s firmware version.
„
Tool Library – Displays the Tool Library menu, which provides
access to OBD1 and OBD2 DTC libraries and to definitions for
Monitor icons and LED indications.
„
Tool Settings – Displays the Tool Settings menu, which lets you
make several adjustments and settings to configure the Scan Tool
to your particular needs.
The System Tests and Vehicle Information options are
shown only when the Scan Tool is in Global OBD2 mode.
SYSTEM TEST MENU
Additional tests are accessed through the Mode Test menu. The
following functions are available:
„
O2 Sensor Test - Retrieves and displays O2 sensor monitor test
results from your vehicle's on-board computer.
„
OBD Monitor Test - Retrieves and displays test results for
emission-related powertrain components and systems that are not
continuously monitored.
„
EVAP Test - Performs a leak test for the vehicle's EVAP system.
1. While linked to the vehicle, press M.
28
Additional Tests
SYSTEM TEST MENU
„
The Main Menu displays.
2. Select System Tests, then press ENTER
.
„
The System Test menu displays.
If System Tests is not shown
on the Main Menu, the System
Tests
functions
are
not
available for your vehicle.
O2 Sensor Test
OBD2 regulations require that applicable vehicles monitor and test operation
of the oxygen (O2) sensors to identify problems that can affect fuel
efficiency and vehicle emissions. These tests are performed automatically
when engine operating conditions are within predefined limits. Results of
these tests are stored in the on-board computer's memory.
The O2 Sensor Test function lets you retrieve and view O2 sensor
monitor test results for the most recently completed tests from your
vehicle's on-board computer.
The scan tool does not perform O2 sensor tests, but retrieves
results from the most recently performed O2 sensor tests from
the on-board computer's memory. You may retrieve O2 sensor
test results for only one test of one sensor at any given time.
1. From the System Test menu, select O2
Sensor Test, then press ENTER
.
2. A "One moment please..." message
displays, followed by the select sensor
screen.
If O2 sensor test data is not
presently stored in the vehicle’s
computer, an advisory message
displays. Press M to return to the Main Menu.
If O2 sensor tests are not supported by the vehicle under test,
an advisory message displays. Press M to return to the Main
Menu.
3. Select the O2 sensor for which you wish
to view test results, then press ENTER
to display the test results.
4. When test results have been retrieved,
data for the selected sensor test will
show on the Scan Tool's display.
5. When you have finished viewing the retrieved test data:
„ To view test results for the next sensor, select Next, then press
ENTER
.
„
To return to the Select Sensor screen, select Back, then press
ENTER
.
29
Additional Tests
SYSTEM TEST MENU
6. When you have finished viewing test data for all desired sensors,
select Back, then press ENTER
to return to the System Test
menu; or, press M to return to the Main Menu.
OBD Monitor Test
The OBD Monitor Test function retrieves and displays test results for
emission-related powertrain components and systems that are not
continuously monitored. The tests available are determined by the
vehicle manufacturer.
The Scan Tool does not perform the OBD monitor test, but
retrieves results from the most recently performed tests from
the on-board computer’s memory. You may retrieve OBD
monitor test results for only one test at any given time.
1. From the System Test menu, select
OBD Monitor Test, then press ENTER
.
2. A “One moment please. . .” message
displays, followed by the Select Test
screen. (Refer to the vehicle’s service
repair manual for information related to
non-continuous tests.)
If OBD monitor test data is not presently stored in the vehicle’s
computer, an advisory message displays. Press M to return to
the Main Menu.
If OBD monitor tests are not supported by the vehicle under test,
an advisory message displays. Press M to return to the Main
Menu.
3. Select the desired test, then press
ENTER
to display the test results.
The display shows the following
information:
„
Test ID number
„
Module ID number
„
Component ID number
„
Min or Max test limit (Only one test limit, either Min or Max, is
shown for any given test.)
„
Test Value and status
Status is calculated by the Scan Tool by comparing the Test
Value against the displayed test limit (either Min or Max).
Status is shown as either Low, High or OK.
4. When you have finished viewing the retrieved test data, select Back
on the Select Test screen, then press ENTER
to return to the
System Test menu; or, press M to return to the Main Menu.
30
Additional Tests
SYSTEM TEST MENU
EVAP Test
The EVAP Test function lets you initiate a leak test for the vehicle's
EVAP system.
The Scan Tool does not perform the leak test, but signals to
vehicle's on-board computer to initiate the test. The vehicle
manufacturer determines the criteria and method for stopping the
test once it has been started. Refer to the vehicle's service repair
manual to determine the procedures necessary to stop the test.
1. From the System Test menu, select
EVAP Test, then press ENTER
.
2. A "One moment please..." message
displays.
3. When the EVAP leak test has been
initiated by the vehicle's on-board
computer, a confirmation message
displays. Select Back, then press ENTER
to return to the System Test menu; or,
press M to return to the Main Menu.
Some vehicle manufacturers do not
allow diagnostic tools or other
external devices to control vehicle
systems. If the EVAP Test is not
supported by the vehicle under test,
an advisory message displays. Press the M button to return to
the Main Menu.
RESETTING THE OIL MAINTENANCE LIGHT
1. While linked to the vehicle, press M.
„
The Main Menu displays.
2. Select Service Reset,
ENTER
to continue.
„
then
press
The Service Reset screen displays.
3. Select Oil Reset, then press ENTER
.
„
The Oil Reset screen displays.
„
If the vehicle under test is equipped
with a navigation system, select Yes,
then press ENTER
to continue.
„
If the vehicle under test is not
equipped with a navigation system,
select No, then press ENTER
to
continue.
31
Additional Tests
RESETTING THE OIL MAINTENANCE LIGHT
If the Scan Tool cannot reset the
Oil Maintenance Light, an “instructional” dialog displays, showing
the manual procedures for resetting the indicator light. When
finished viewing the instructions,
press M to return to the Main
Menu.
4. The Reset Oil Maintenance Indicator
screen displays.
„
If you do not wish to proceed with the
reset process, select No, then press
ENTER
to return to the System
Menu.
„
If you wish to proceed with the reset
process, select Yes, then press
ENTER
to continue.
5. When the reset process has competed,
a confirmation message displays. Press
M to return to the Main Menu.
„
If the oil reset was not successful,
an advisory message displays.
„
To perform the oil reset by procedure, select Yes, then press
. An “instructional” message displays, showing the
ENTER
manual procedures for resetting the indicator light.
„
If you do not wish to perform the oil reset by procedure, select
No, then press ENTER
to return to the Main Menu.
PERFORMING A SERVICE CHECK
The Service Check function lets you check the current oil level and oil
life.
1. While linked to the vehicle, press M.
„
The Main Menu displays.
2. Select Service Check, then press
ENTER
.
„
The Service Check screen displays.
„
The screen shows the current
Engine Oil Level and Oil Life
Remaining.
3. When you have finished viewing the
information, press M to return to the
Main Menu.
32
Additional Tests
BATTERY/ALTERNATOR TEST
BATTERY/ALTERNATOR TEST
The Scan Tool can perform a check of the vehicle’s battery and
alternator system to ensure the system is operating within acceptable
limits. You can perform a battery check only, or an alternator system
(battery and alternator) check.
To perform a battery check ONLY:
1. Press M and release.
„
The Main Menu displays.
2. Select Battery/Alternator Test, then
press ENTER
.
„
The Battery/Alternator Monitor Test
displays.
3. Select Battery Test, then press ENTER
.
„
An “instructional” message displays, showing the procedures to
prepare the vehicle for the battery check.
4. Prepare the vehicle for the battery check:
„
Turn the engine off.
„
Place the transmission in PARK or NEUTRAL, and set the
parking brake.
„
Make a visual check of the battery’s condition. If the battery
terminals are corroded or other damage is present, clean or
replace the battery as appropriate.
„
For “unsealed” batteries, make sure the water level in each cell
is above the battery plates.
„
Turn the ignition on. DO NOT start the engine.
5. Press ENTER
to begin the battery check.
If the engine is running, an advisory message shows. Turn
the engine off, then turn the ignition on. DO NOT start the
engine. Press ENTER
to continue.
„
An “instructional” message shows.
6. Turn the vehicle’s headlights on, the press ENTER
to continue.
„
A “countdown” message shows while the battery check is in
process.
„
If battery voltage is less than 12.1 volts, an advisory message
shows. Press M to return to the Main Menu. Turn the ignition off
and disconnect the Scan Tool from the vehicle. Fully charge the
battery, then repeat the battery check.
„
If battery voltage is greater than 12.1 volts, an “instructional”
message shows.
7. Turn the vehicle’s headlights off, then press ENTER
to continue.
33
Additional Tests
USING THE DLC LOCATOR - VIEWING VEHICLE INFORMATION
„
An “instructional” message shows.
8. Start the vehicle’s engine. Allow the engine to run for several
seconds, then turn the engine off. Repeat for a total of three
“start/stop” cycles.
If the Scan Tool did not detect “cranking status” for the
vehicle’s engine, an advisory message shows. Press
to repeat the battery check, or, press M to
ENTER
return to the Main Menu.
9. When the battery check is complete, a
results screen displays the battery
status. The System Status LEDs
provide a PASS/FAIL indication, as
follows:
„
Green = Good
„
Yellow = Normal
„
Red = Warning/Bad
10. Press M to return to the Main Menu.
To perform a charging system check:
1. Press M and release.
„
The Main Menu displays.
2. Select Battery/Alternator
then press ENTER
.
„
Monitor,
The Battery/Alternator Test Menu
displays.
3. Select Alternator Monitor, then press
ENTER
.
„
An “instructional” message shows.
4. Start and warm the engine to normal operating temperature. Turn on
to continue.
the headlights. Press ENTER
„
An “instructional” message shows.
5. Press the accelerator pedal to raise engine speed to 2000 RPM,
and maintain the engine speed.
„
When engine speed is within the
required range, the alternator test
begins. A progress screen shows.
„
When the “countdown” timer expires,
an “instructional” message shows.
6. Turn the vehicle’s headlights off, and
return the engine to idle speed.
„
34
A “One moment please…” message displays while the test
results are retrieved.
Additional Tests
BATTERY/ALTERNATOR TEST
7. When the alternator check is complete,
a results screen shows charging system
voltage and indicates whether or not the
charging system is within acceptable
limits. The System Status LEDs provide
a PASS/FAIL indication, as follows:
„
Green = System within limits
„
Yellow = Over charging or under
charging
„
Red = Excessive over charging or under charging
„
If the alternator voltage is less than 9 V, the red, yellow and
green SYSTEM STATUS LEDs will flash on and off.
8. Press M to return to the Main Menu.
USING THE DLC LOCATOR
1. Select DLC Locator in the Main Menu, then press ENTER
„
The Select Vehicle Model Year screen displays.
2. Select the desired vehicle model year, then press ENTER
„
.
The Select Vehicle Manufacturer screen displays.
3. Select the desired vehicle manufacturer, then press ENTER
„
.
.
The Select Vehicle Model screen displays.
4. Select the desired model, then press ENTER
„
The DLC Location screen for the
selected vehicle displays.
„
The DLC Location screen shows the
selected vehicle make and model, a
description of the DLC location and
whether the DLC is “covered” or
“uncovered,” and includes a picture
of the DLC location.
.
5. When you have finished viewing the DLC location, press any hotkey
to exit the DLC Locator.
VIEWING VEHICLE INFORMATION
The Vehicle Information function offers three options for retrieving
reference information for the vehicle under test; Vehicle ID, Available
Modules and IPT (In-Use Performance Tracking).
Retrieving Vehicle ID Information
The Vehicle ID function is applicable to model year 2000 and
newer OBD2-compliant vehicles.
35
Additional Tests
VIEWING VEHICLE INFORMATION
The Scan Tool can retrieve a list of information (provided by the vehicle
manufacturer), unique to the vehicle under test, from the vehicle's onboard computer. This information may include:
„
The vehicle's VIN number
„
The control module identification number
„
The vehicle's calibration ID(s). These IDs uniquely identify the
software version(s) for the vehicle's control module(s).
„
The Vehicle's Calibration Verification Number(s) (CVNs) required by
ODB2 regulations. CVNs are used to determine if emission-related
calibrations for the vehicle under test have been changed. One or
more CVNs may be returned by the vehicle's computer.
1. With the Scan Tool in OBD2 mode, press M.
„
The Main Menu displays.
2. Select Vehicle Information, then press
ENTER
.
„
The Vehicle
displays.
Information
menu
3. Select Vehicle ID, then press ENTER
.
The first time the Vehicle ID
function is used, it may take several
minutes to retrieve the information
from the vehicle's computer.
4. When the retrieval process is completed,
the vehicle ID information displays.
5. When you have finished viewing the
retrieved vehicle ID information, press
M to return to the Main Menu.
Viewing Available Modules
The Scan Tool can retrieve a list of modules supported by the vehicle
under test.
1. With the Scan Tool in OBD2 mode, press M.
„
The Main Menu displays.
2. Select Vehicle Information, then press
.
ENTER
„
The Vehicle
displays.
Information
menu
3. Select Available Modules, then press
.
ENTER
4. When the retrieval process is completed, a complete list of modules
supported by the vehicle under test displays.
36
Additional Tests
VIEWING VEHICLE INFORMATION
5. When you have finished viewing the list of available modules, press
M to return to the Main Menu.
Viewing In-use Performance Tracking (IPT)
The Scan Tool can retrieve In-use Performance Tracking (IPT) statistics
for monitors supported by the vehicle under test. Two values are
returned for each monitor; the number of times that all conditions
necessary for a specific monitor to detect a malfunction have been
encountered (XXXCOND), and the number of times that the vehicle has
been operated under the specific conditions for the monitor (XXXCOMP).
Statistics are also provided for the number of times the vehicle has been
operated in OBD monitoring conditions (OBDCOND), and the number of
times the vehicle’s engine has been started (IGNCNTR).
1. With the Scan Tool in OBD2 mode, press M.
„
The Main Menu displays.
2. Select Vehicle Information, then press the ENTER
„
button.
The Vehicle Information menu displays.
3. Select IPT, then press ENTER
.
4. When the retrieval process is completed,
the In-use Performance Tracking
statistics for the vehicle under test
display.
„
If In-use Performance Tracking is
not available for your vehicle, an
advisory message shows on the
Scan Tool’s display. Press M to
return to the Main Menu.
5. When you have finished viewing the statistics, press M to return to
the Main Menu.
VIEWING THE FIRMWARE VERSION
1. Select Firmware Version in the Main
Menu, then press ENTER
.
„
The Firmware Version screen displays for four seconds.
„
The screen shows the Scan Tool’s
current firmware version, bootloader
version and database version.
2. The display returns to the Main Menu.
37
Additional Tests
THE TOOL LIBRARY
THE TOOL LIBRARY
The Tool Library contains valuable reference information for the Scan
Tool. The following functions are available:
„
Tool Icons – Shows the full names for the I/M MONITOR STATUS
icons shown and descriptions of informational icons on the Scan
Tool’s display.
„
DTC Library – Provides access to libraries of OBD2 DTC definitions.
„
LED Meaning – Provides descriptions of the meaning of the Scan
Tool SYSTEM STATUS LEDs.
1. While linked to the vehicle, press M.
„
The Main Menu displays.
2. Select Tool Library, then press ENTER
.
„
The Tool Library menu displays.
Viewing Tool Icon Descriptions
The I/M MONITOR STATUS icons on the Scan Tool’s LCD display
provide an indication of the “Completed / Not Complete” status for all I/M
Monitors supported by the vehicle under test. The Tool Icons function
displays the full name for each Monitor icon, as well as descriptions of
the meanings of other informational icons shown on the Scan Tool’s
display.
1. From the Tool Library menu, select Tool Icons, then press ENTER
.
„
The Tool Icons screen displays.
„
The screen shows a list of the 15
Monitor icons, along with the full
name for each icon, as well as
descriptions of the meanings of
other informational icons. Use the
UP
and DOWN
buttons, as
necessary, to scroll the list.
2. When you have finished viewing the
tool icon descriptions, press M to return
to the Main Menu.
Using the DTC Library
1. From the Tool Library menu, select
DTC Library, then press ENTER
.
„
The Select Library screen displays.
2. Select OBD2
.
ENTER
38
Library,
then
press
Additional Tests
THE TOOL LIBRARY
„
The Select Manufacturer screen
displays.
3. Select the desired vehicle manufacturer,
then press ENTER
.
„
The Enter DTC screen displays.
The screen shows the code
“P0001,” with the “P” highlighted.
4. Use the UP
and DOWN
buttons,
as necessary, to scroll to the desired
DTC type (P=Powertrain, U=Network,
B=Body, C=Chassis), then press the
DTC/FF button.
„
The selected character displays solid,
and the next character is highlighted.
5. Select the remaining digits in the DTC
in the same way. When you have
selected all the DTC digits, press
ENTER
to view the DTC definition.
6. When you have finished viewing the DTC
definition, highlight Back, then press
ENTER
to return to the Enter DTC
screen and enter additional DTCs; or,
press M to return to the Main Menu.
If a definition for the DTC you entered is not available, an advisory
message shows. Highlight Back, then press ENTER
to return
to the Enter DTC screen and enter additional DTCs; or, press M to
return to the Main Menu.
Viewing LED Meaning
The SYSTEM STATUS LEDs on the Scan Tool provide a visual
indication of the I/M Readiness status of the vehicle under test. The
LED Meaning function provides a description of the meanings of the
green, yellow and red SYSTEM STATUS LEDs.
1. From the Tool Library menu, select LED
Meaning, then press ENTER
.
„
The LED Meaning screen displays.
„
The screen provides a description of
the meanings of the green, yellow
and red SYSTEM STATUS LEDs.
2. When you have finished viewing the
LED meanings, press M to return to the
Main Menu.
39
Additional Tests
ADJUSTMENTS AND SETTINGS
ADJUSTMENTS AND SETTINGS
The Scan Tool lets you make several adjustments and settings to
configure the Scan Tool to your particular needs. The following
adjustments and settings are available:
„
Adjust Brightness: Adjusts the brightness of the display screen.
„
Audible Tone: Turns the Scan Tool’s audible tone “on” and “off.”
When turned “on,” a tone sounds each time a button is pressed.
„
Footer Messages: Turns the navigational “footers” at the bottom of
most display screens “on” and “off.”
„
Hotkey Legend: Shows functional descriptions for the Scan Tool’s
hotkeys.
„
Language Selection: Sets the display language for the Scan Tool
to English, French or Spanish.
„
Unit of Measurement: Sets the Unit of Measurement for the Scan
Tool’s display to USA or metric.
To enter the Tool Settings mode:
1. While linked to the vehicle, press and release M.
„
The Main Menu displays.
2. Select Tool
.
ENTER
„
Settings,
then
press
The Tool Setting menu displays.
3. Make adjustments and settings as
follows.
Adjusting Display Brightness
1. Select Adjust Brightness in the Tool
Settings menu, then press ENTER
.
„
The Adjust Brightness screen displays.
to make
and DOWN
2. Press UP
the display lighter or darker, then press
ENTER
to save your changes.
To return to the Tool Settings menu without making changes,
press M.
Enabling/Disabling the Audible Tone
1. Select Audible Tone in the Tool
Settings menu, then press ENTER
.
„
The Audible Tone screen displays.
2. Select On or Off as desired, then press
to save your changes.
ENTER
40
Additional Tests
ADJUSTMENTS AND SETTINGS
To return to the Tool Settings menu without making changes,
press M.
Enabling/Disabling Navigational Footers
1. Select Footer Messages in the Tool
.
Settings menu, then press ENTER
„
The Footer Messages screen displays.
2. Select On of Off as desired, then press
ENTER
to save your changes.
To return to the Tool Settings menu without making changes,
press M.
Viewing the Hotkey Legend
1. Select Hotkey Legend in the Tool Settings menu, then press
ENTER
.
„
The Hotkey Legend screen displays.
„
The screen shows a functional
description of each of the Scan
Tool’s hotkeys.
2. When you have finished viewing the
to
Hotkey Legend, press ENTER
return to the Tool Settings menu.
Selecting the Display Language
1. Select Language Selection in the Tool
Settings menu, then press ENTER
.
„
The Language Selection screen displays.
2. Select the desired display language,
then press ENTER
to save your
changes.
To return to the Tool Settings menu without making changes,
press M.
Setting the Unit of Measurement
1. Select Unit of Measurement in the
Tool Settings menu, then press ENTER
.
„
The Unit of Measurement screen
displays.
41
Additional Tests
ADJUSTMENTS AND SETTINGS
2. Select the desired unit of measurement, then choose Save to save
your changes.
To return to the Tool Settings menu without making changes,
press M.
Exiting the MENU Mode
„
42
Press M to return to the Main Menu.
Notes
43
Notes
44
Warranty and Servicing
LIMITED ONE YEAR WARRANTY
The Manufacturer warrants to the original purchaser that this unit is free
of defects in materials and workmanship under normal use and
maintenance for a period of one (1) year from the date of original
purchase.
If the unit fails within the one (1) year period, it will be repaired or
replaced, at the Manufacturer’s option, at no charge, when returned
prepaid to the Service Center with Proof of Purchase. The sales receipt
may be used for this purpose. Installation labor is not covered under this
warranty. All replacement parts, whether new or remanufactured,
assume as their warranty period only the remaining time of this warranty.
This warranty does not apply to damage caused by improper use,
accident, abuse, improper voltage, service, fire, flood, lightning, or other
acts of God, or if the product was altered or repaired by anyone other
than the Manufacturer’s Service Center.
The Manufacturer, under no circumstances shall be liable for any
consequential damages for breach of any written warranty of this unit.
This warranty gives you specific legal rights, and you may also have
rights, which vary from state to state. This manual is copyrighted with all
rights reserved. No portion of this document may be copied or
reproduced by any means without the express written permission of the
Manufacturer. THIS WARRANTY IS NOT TRANSFERABLE. For
service, send via U.P.S. (if possible) prepaid to Manufacturer. Allow 3-4
weeks for service/repair.
SERVICE PROCEDURES
If you have any questions, require technical support or information on
UPDATES and OPTIONAL ACCESSORIES, please contact your local
store, distributor or the Service Center.
USA & Canada:
(800) 544-4124 (6:00 AM-6:00 PM PST, Monday through Saturday)
All others: (714) 241-6802 (6:00 AM-6:00 PM PST, Monday through
Saturday)
FAX: (714) 241-3979 (24 hr.)
Web: www.innova.com
45
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement