FLASH Thermoflash DIGI 2 HF Schnellstartanleitung
Add to my manuals20 Pages
The FLASH Thermoflash DIGI 2 HF is a feature-rich thermostat programmable that offers a wide range of possibilities for programming and regulating your heating. It comes with three pre-defined heating programs and allows for creating customized schedule. Easy to install and simple to program, the kit enables precise temperature regulation and energy saving without any construction work. The wireless thermostat and wall-mounted receiver communicate via radio frequency, so you can place the thermostat anywhere you want, without worrying about wiring.
advertisement
Kit Thermoflash DIGI 2 HF
réf. 56460
Thermostat programmable sans fil et récepteur mural
Thermostat programmable à cycle hebdomadaire et récepteur mural IP43
FR IT
GB ES
DE
Présentation des produits
Le thermostat DIGI 2 HF
Simple à installer et facile à programmer, le kit DIGI 2 HF vous permet, sans travaux, de programmer et réguler votre chauffage.
Température
économique
Température confort
Touches +/pour les réglages
Indicateur du niveau de température en cours confort ou économique
+
-
Auto Manu
¡c
¡c
Indicateur du jour de la semaine
Température ambiante
1 2 3 4 5 6 7 timer days
Témoin d'usure des piles
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MODE
Indicateur d’enclenchement du chauffage ou de la climatisation
Sélection des modes
Absence prolongée
(vacances)
Visualisation des périodes confort et
économique
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Le kit DIGI 2 HF a été conçu pour vous apporter confort et économies d’énergie. Il s’installe facilement dans votre logement, il régule la température ambiante en fonction de la programmation et envoie des ordres marche/arrêt au récepteur mural installé à proximité de la chaudière ou de l’émetteur de chaleur à gérer.
Le kit DIGI 2 HF régule la température ambiante selon
3 niveaux de température.
• Température confort : c’est la température que vous souhaitez pendant vos heures de présence.
• Température économique : c’est la température que vous souhaitez pendant vos absences de courte durée ou pendant la nuit.
minimale assurée pendant vos absences prolongées.
Elle protège votre logement des risques du gel.
Installation du thermoflash DIGI 2 HF
Pour bien assurer sa fonction de régulation de la température ambiante, le DIGI 2 HF doit être installé à environ 1,5 m du sol, sur un mur intérieur,
à l’abri du rayonnement direct et de toute source de chaleur telle que : téléviseur, lampe, radiateur, courant d’air etc.
A l’aide du socle fourni avec le DIGI 2 HF, vous pouvez le poser simplement sur un meuble en veillant à ce qu’aucun facteur externe ne l’influence
(radiateur, fenêtre, téléphone portable etc.).
Sélection des jours de la semaine
(1 = lundi, 2 = mardi...
7 = dimanche)
Choix du programme
P1 à P4
Réglage température confort
Réglage température
économique
Validation Réglage comptage horaire
Remise
à zéro générale
Vous pouvez également le fixer au mur.
• Pour cela, déclipsez-le socle mural.
Le récepteur mural IP43
Le récepteur mural IP43 s’installe facilement et discrètement à proximité de la chaudière. Il reçoit les ordres marche/arrêt en provenance du DIGI 2 HF et les transmet à la chaudière via une sortie filaire.
Bouton poussoir de configuration et de forçage.
Témoin de mise sous tension et de codage.
Voyant allumé = le produit est alimenté.
Ce voyant clignote lors des opérations de codage.
Témoin de fonctionnement.
Ce voyant est allumé lorsque le contact de sortie du récepteur est fermé = ON.
• Fixez le au mur.
!
Important :
l’ensemble émetteur + récepteur est codé en usine, il est donc immédiatement fonctionnel.
Inutile de refaire le codage.
Mise en place ou remplacement des piles
Ce thermostat programmable est pourvu d’un témoin d’usure des piles, veuillez, dès son apparition en bas à droite de l’afficheur, procéder au remplacement de celles-ci (utilisez 2 piles 1,5 V alcalines LR6, l’autonomie est de 12 mois).
Lors du remplacement des piles, le programmateur conserve ses programmes pendant 60 secondes.
Réinitialisation
Avant de commencer la programmation de votre appareil, veuillez abaisser le capot et appuyer sur la touche
RESET
à l’aide d’une pointe de stylo.
0000
h
• Raccrochez le produit sur son socle.
1
Mise à l’heure et au jour actuel
C’est la première mise en service.
• Vous venez d’appuyer sur la touche
RESET
.
• Les inscriptions
I2:00 et le pointeur
▲ sous le jour 1
(lundi) clignotent.
1 2 3 4 5
1 2 3 4 5 6 7
+
☛
-
DAYS
☛
1-7
PROG
P1-P4
OK
0000
h
Res
Mettez à l’heure avec les touches
+
/
-
(un appui prolongé sur la touche accélère le défilement de l’heure).
Réglez le jour actuel par appuis successifs sur la touche
DAYS 1-7
,un pointeur
▲ apparaît sous le jour correspondant (1 = lundi, 2 = mardi,
3 = mercredi etc.).
Validez avec la touche
OK
.
Vous souhaitez modifier l’heure ou le jour : appuyez sur la touche
MODE
jusqu’à l’apparition du pointeur
▲ sous le sigle horloge et procéder comme ci-dessus aux points , et .
Réglage des températures
Les températures confort et économique sont préréglées : Confort = 20°C, Economique = 16°C.
☛ ☛
MODE
P3
= Température confort de
6h
à
8h30
, de
11h30
à
13h30
et de
16h30
à
23h
.
Température économique de
8h30
à
11h30
, de
13h30
à
16h30
et de
23h
à
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P4
=
Programme libre
vous permettant de créer des périodes en température confort et des périodes en température
économique. Ce programme P4 peut
être différent pour chaque jour de la semaine.
Sélection d’un programme existant P1, P2,
P3, pour un jour de la semaine (en mode programmation, toutes les modifications se valident automatiquement).
exemple :
P2 pour mercredi
+
-
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
Appuyez sur la touche plusieurs fois pour obtenir l’horaire 6:00 : chaque appui bref vous fait progresser de 30 minutes et un appui prolongé accélère la progression.
• Appuyez sur la touche obtenir l’horaire 8:00 .
• Appuyez sur la touche obtenir l’horaire I2:00 .
• Appuyez sur la touche obtenir l’horaire I4:00 .
• Appuyez sur la touche obtenir l’horaire I8:00 .
• Appuyez sur la touche obtenir l’horaire 22:00 .
plusieurs fois pour plusieurs fois pour plusieurs fois pour plusieurs fois pour plusieurs fois pour
Nota :
si vous avez fait une erreur (ex : 11h30 au lieu de 12h00) utilisez les touches
+
/
-
pour avancer ou reculer et corriger à l’aide des touches
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
-
Auto Manu
c
¡c c
¡c
1 2 3 4 5 6 7
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
Modification de la température confort
Appuyez sur la touche .
Modifiez la température avec les touches
+
/
-
.
Validez avec la touche
OK
.
Modification de la température économique
Appuyez sur la touche .
Modifiez la température avec les touches
+
/
-
.
Validez avec la touche
OK
.
La programmation
PROG
P1-P4
Pour programmer votre semaine vous diposez de 4 programmes :
P1
,
P2
,
P3
, qui sont préenregistrés et non modifiables.
P4
est libre et vous permet de créer un programme personnalisé et différent pour chaque jour de la semaine.
P1
= Température confort de
6h
à
23h
.
Température économique de
23h
à
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
!
P1 est affecté aux 7 jours de la semaine par défaut. S’il correspond à votre rythme de vie restez en mode automatique, sinon continuez.
Appuyez sur la touche
PROG P1-P4
pour passer en mode programmation.
Le N° du programme affecté au jour clignote sur la partie droite de l’afficheur.
Appuyez sur la touche
DAYS 1-7
jusqu’à l’apparition du pointeur
▲ sous le jour que vous souhaitez programmer dans notre exemple mercredi.
Appuyez sur la touche
PROG P1-P4
jusqu’à l’apparition dans la partie droite de l’écran du numéro de programme P2 clignotant.
Validez avec la touche
OK
, le jour suivant vous est automatiquement proposé.
Création d’un programme
P4
Un profil de 24h, composé de 48 thermomètres en bas de l’afficheur,vous permet de visualiser aisément la composition de votre programme.
Un thermomètre à moitié vide correspond à
30 minutes en température économique.
Un thermomètre plein correspond à 30 minutes en température confort.
exemple :
création de 3 périodes en température confort pour le vendredi : de
6h
à
8h
, de
12h
à
14h
et de
18h
à
22h
.
1 2 3 4 5 6 7
+
-
Auto Manu
¡c
¡c
DAYS
1-7
2
☛
0
0
1
1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PROG
P1-P4
☛ ☛ ☛
0000
h
Res
☛ ☛
MODE
Depuis le mode
Auto
, appuyez sur la touche
PROG P1-P4
.
Avec la touche
DAYS 1-7
sélectionnez le jour de
1 à 7 et vérifiez votre programme sur le profil de
24h en bas de l’afficheur (exemple ci-dessous).
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Appuyez sur
MODE
pour revenir en mode
Auto
.
Le mode automatique (Auto)
Le passage en mode automatique se fait en appuyant sur la touche
MODE
jusqu’à l’apparition du pointeur
▲ sous
Auto
.
MODE
En mode automatique, l’horloge thermostat s’adapte à votre rythme
Auto Manu
° c de vie en réalisant le ou les programme(s) que vous avez choisi(s).
☛ ☛
Le mode manuel (Manu)
Le mode manuel transforme votre appareil en un simple thermostat.
Il vous permet de maintenir une température constante dans votre logement (réglable de 5°C à
30°C).
P2
= Température confort de
6h
à
8h30
et de
16h30
à
23h
.
Température économique de
8h30
à
16h30
et de
23h
à
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
2
Modification temporaire de la température
En mode automatique, cette fonction très pratique vous permet de modifier temporairement la température ambiante.
Auto Manu
• Pour augmenter la température appuyez sur la touche
+
(plusieurs appuis si nécessaire).
• Pour abaisser la température appuyez sur la touche
-
☛
☛
+
nécessaire).
0 1
¡c
¡c
2 3 4 5
L’indicateur du niveau de température en cours
(confort ou économique) se met à clignoter.
Cette modification prendra fin lors du prochain changement de température programmée.
Pour revenir au programme initial, appuyez sur
MODE
et replacez le pointeur
▲ sous
Auto
.
L’arrêt du clignotement de l’indicateur du niveau de température en cours (confort ou économique) marque la fin de la modification temporaire.
Le mode absence prolongée vacances
Ce mode met votre logement à l’abri des risques du gel en maintenant une température minimum réglable dans votre logement durant vos absences.
Vous pouvez programmer la durée de votre absence pour prévoir la remontée en température de votre logement à votre retour.
2 possibilités de maintien hors-gel :
Forçage hors-gel permanent
• Appuyez sur , le jour 0I clignote.
• Appuyez une fois sur la touche
-
, l’affichage F
ORC clignote.
• Validez avec la touche
OK
.
• Réglez le niveau de température souhaité pendant votre absence avec les touches
+
/
-
.
• Validez avec la touche
OK
.
Pour annuler et revenir en mode
Auto
, appuyez sur la touche
MODE
.
Maintien hors-gel pour un nombre de jours
• Appuyez sur
,
le jour 0I clignote.
• Avec les touches
+
/
-
, réglez la durée de votre absence en jour (de 1 à 99 jours).
La journée en cours compte pour 1
.
• Validez avec la touche
OK
.
• Réglez le niveau de température souhaité pendant votre absence avec les touches
+
/
-
.
•
OK
. Le thermostat repassera en mode
Auto
à la fin de la période réglée.
Pour annuler et revenir en mode
Auto
, appuyez sur la touche
MODE
.
Signal d’entretien de votre
0000
installation
h
Ce mode vous permet soit :
• de penser à faire effectuer un entretien périodique
(changement de filtre sur un climatiseur, le nettoyage d’un appareil).
• de comparer vos consommations de chauffage ou d’air conditionné d’une année sur l’autre (en comparant le nombre d’heures d’enclenchement).
Comptage du nombre d’heures d’enclenchement
Auto Manu
1 2 3 4 5 6 7
+
timer
☛ ☛
MODE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS PROG
0000
OK
1-7 P1-P4
☛
h
Res
☛
Appuyez sur la touche
0000 h l’afficheur vous indique, depuis la mise en place des piles, le nombre d’heures d’enclenchement de votre brûleur,climatiseur,ventilo-convecteur,etc.selon
le type d’appareil commandé (un appui sur
+
ou
-
remet le compteur à zéro).
Appuyez sur
MODE
pour revenir en mode
Auto
.
Programmation de la périodicité d’entretien de votre installation
Appuyez sur la touche
0000 h
.
Réglez avec les touches
+
/
-
le nombre d’heures de fonctionnement à partir duquel vous souhaitez
être averti.
Validez avec la touche
OK
;le décomptage commence.Vous serez averti par l’apparition du sigle
timer
de la fin du décomptage.
Réglages éventuels
Vous pouvez procéder à différents réglages au dos de l’appareil
(lorsqu’il est débroché).
1-
Sélection du type d’installation
■
Chauffage
■
Air conditionné
2- Sélection du mode de régulation
■
Tout ou rien
■
Chronoproportionnel
Le mode chronoproportionnel est plus particulièrement conseillé pour des installations de planchers chauffants (forte inertie).
3-
Fonction anti-blocage de la pompe de circulation (enclenchement de la pompe durant 1 minute toutes les 24 heures)
■
Arrêt fonction anti-blocage
■
Marche fonction anti-blocage
Configuration
Pour associer un émetteur au récepteur :
• Appuyez pendant plus de 3 secondes sur le bouton poussoir du récepteur.
• Le voyant
OK
clignote, relâchez la touche.
Vous êtes en mode configuration.
• Appuyez pendant 3 secondes sur le bouton
RESET
du Thermoflash DIGI 2 HF.
• Le voyant
OK
du récepteur s'arrête de clignoter au bout de 5 secondes environ.
Le lien émetteur/récepteur est établi.
Mise à zéro
Pour effacer tous les liens émetteur/récepteur :
• Appuyez pendant plus de 10 secondes sur le bouton poussoir du récepteur.
• Le voyant
OK
clignote lentement puis plus rapidement.
• Ré-appuyez pendant 3 secondes sur le bouton poussoir du récepteur.
• Le voyant
OK
arrête de clignoter, tous les liens sont effacés.
Le récepteur retourne en mode
Auto
.
Forçage
La commande manuelle est disponible sur ce produit.
• Appuyez brièvement sur le bouton poussoir du récepteur (appui < 3 s.).
Chaque appui bref inverse l’état de la sortie.
Remarque :
la commande radio reste prioritaire.
3
Que faire si ?
•
Le chauffage ne se met pas en marche:
- le récepteur n’est pas alimenté : (voyant
OK
éteint).Vérifiez le fusible et le disjoncteur.
•
Le récepteur est hors de portée de l’émetteur :
- rapprochez-vous suffisamment du récepteur.
•
Le récepteur ne reconnaît pas le code de l’émetteur :
- reconfigurez le récepteur.
•
L'application ne se met pas en marche ou ne s’arrête pas :
- le récepteur ou l'émetteur est dans une zone perturbée par des émissions d'ondes (radio amateur, télévision, borne réseau GSM etc.) : déplacez le récepteur ou l'émetteur hors de la zone perturbée.
Si le problème persiste contactez votre électricien.
Caractéristiques techniques
Emetteur
Plage de réglage de la T° confort : +5°C à +30°C
Plage de réglage de la T° réduite : +5°C à +30°C
Plage de réglage de la T° vacances : +5°C à +30°C
Plage d’affichage de la T° ambiante : 0°C à +40°C
Différentiel statique :
Alimentation :
< 0.3°C
2 piles alcalines 1,5 V LR6
(pour alimenter l’ensemble du produit, transmission radio comprise)
Portée typique : 75 m. en champ libre
3 étages dans l’habitat typique
Fréquence d’émission :
Rapport cyclique d’émission :
433.92 MHz
10%
IP : 30
Température de fonctionnement : 0°C à +40°C
Température de stockage :
Hygrométrie :
Degré de pollution :
Dimensions :
Normes :
-20°C à +70°C
95% à 40°C normal
115 x 82 x 34 mm
EN 301-489-3
Récepteur
Alimentation : 230 V +10 % à -15 %
Charge minimale : 12 V 100 mA
Sortie : 1 contact inverseur libre de potentiel
Pouvoir de coupure :
AC1 :
Inductif :
Fréquence radio :
16 A 250 V
3 A (cos ϕ
= 0,6)
433.92 MHz
Indice de protection :
Classe d’isolation :
Tenue aux chocs :
T° de fonctionnement :
T° de stockage :
Capacité souple :
Capacité rigide :
Dimensions :
Hygrométrie :
Classe de réception :
Normes :
IP43
II
IK04
-10°C à +60°C
-20°C à +70°C
0,5 à 1,5 mm 2
0,5 à 2,5 mm 2
130 x 60 x 27 mm
90% max. à 20°C
2
EN 60669-2-1
Normes :
EN 300220-3,
EN 301-489-1 et EN 301-489-3.
Utilisable partout en Europe
Installation du récepteur
!
Avant toute intervention, coupez le courant.
Le schéma de câblage ne représente pas les protections. L’installation doit être réalisée par un professionnel dans le respect des normes en vigueur.
Pour faciliter son installation, le kit Thermoflash
DIGI 2 HF est livré avec un câble souple 4 fils de
1,5 mm 2 , longueur 1,20 m (non raccordé).
Pour le raccordement du récepteur HF, nous vous conseillons d’utiliser ce câble, en respectant le code couleur suivant :
brun
= phase
bleu
= neutre
gris noir
liaison vers la chaudière
L
N
5 4 3
L
2
N
1
L
N
5 4 3
L N
2 1
Pour convecteurs sans régulation fil pilote.
!
Dans le cas d’un branchement avec 2 types d’appareils (chauffage et climatisation), veillez à
éteindre l’un des appareils pour éviter que les deux ne fonctionnent simultanément durant la même saison.
5 4 3
L
2
N
1
L
N
4
33 rue Saint-Nicolas
B.P. 50152 - 67704 SAVERNE Cedex
Tél. 03 88 01 88 01 - Fax 03 88 01 88 90 www.flash.fr
Kit Thermoflash DIGI 2 HF
rif. 56460
Cronotermostato senza fili con ricevitore murale
Cronotermostato senza fili, ciclo settimanale con ricevitore murale IP43
FR IT
GB ES
DE
Presentazione dei prodotti
Cronotermostato DIGI 2 HF
Semplice da installare, facile da programmare, il kit DIGI 2 HF vi permette di programmare e regolare il vostro riscaldamento.
Temperatura comfort
Tasti +/– per la regolazione
Indicatore del livello di temperatura in corso comfort o economia
Temperatura economica
+
-
Auto Manu
¡c
¡c
Indicatore del giorno della settimana
Temperatura ambiente
1 2 3 4 5 6 7 timer days
¡c
Spia usura pile
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Indicatore dell’innesto del riscaldamento o del sistema di aria condizionamento
Selezione dei modi
MODE
Assenza prolungata
(vacanze)
Visualizzazione dei periodi comfort e economia
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Il kit DIGI 2 HF è stato concepito per apportare comfort ed economizzare energia. Si installa facilmente nella vostra casa, regola la temperatura ambiente in funzione della programmazione effettuata ed invia comandi marcia/arresto al ricevitore murale installato vicino alla caldaia.
Il kit DIGI 2 HF regola la temperatura ambiente secondo 3 livelli di temperatura.
• Comfort: è la temperatura raccomandata quando siete in casa.
• Ridotto: è la temperatura più gradevole quando siete assenti per breve tempo o durante la notte.
• Antigelo: è la temperatura minima assicurata durante le assenze prolungata. Protegge l’abitazione dai rischi del gelo.
Installazione del DIGI 2 HF
Per assicurare un buon funzionamento ; il DIGI 2 HF deve essere installato a circa 1.5 m dal suolo su un muro interno e riparato da ogni tipo di irraggiamento diretto e da ogni sorgente di calore come ad esempio il televisore, lampade, radiatori, correnti d’aria etc.
Il DIGI 2 HF può essere collocato su un qualsiasi mobile attraverso una sua base di appoggio, verificando che nessun fattore esterno possa influenzarlo (radiatore, finestra etc.).
Selezione dei giorni della settimana
(1 = lunedì, 2 = martedì...
7 = domenica)
Scelta del programma da P1 a P4
Regolazione temperatura comfort
Regolazione temperatura economia
Convalida Regolazione contatore orario
Ras: rimessa a zero generale
Voi potete comunque installarlo a muro.
• Per fare questo, staccate la base di appoggio.
Il ricevitore murale IP43
Il ricevitore murale IP43 si installa facilmente in prossimità della caldaia.
Esso riceve i comandi marcia/arresto provenienti dal DIGI 2 HF e li trasmette alla caldaia via filo.
Pulsante di configurazione e di forzatura.
Spia di messa in tensione e di codifica.
LED acceso = il prodotto è alimentato.
Questo LED lampeggia durante le operazioni di codifica.
Spia di funzionamento. Questo LED è acceso quando il contatto di uscita del ricevitore è chiuso = ON.
!
Importante:
l'insieme emettitore + ricettore viene codificato dal produttore ed é dunque immediatamente funzionante.
Inutile effettuare nuovamente la codifica.
Installazione o sostituzione delle pile
Il DIGI 2 HF è dotato di una spia che controlla la carica delle pile. Non appena la spia appare in basso a destra del display, procedere alla sostituzione delle pile (usare 2 pile 1,5 V alcaline LR6, l’autonomia è di circa 12 mesi).
Durante la sostituzione delle pile DIGI 2 HF conserva i suoi programmi per 60 secondi.
Reinizializzazione
Prima di iniziare la programmazione del vostro apparecchio abbassate il coperchio e premete sul tasto
RESET
con la punta di una biro.
0000
h
• Fissatela al muro.
• Dopo di che appoggiate il DIGI 2 HF sulla base.
5
Programmazione dell’ora e del giorno
E’ la prima messa in servizio.
• Voi avete premuto sul tasto
RESET
.
• Le ore I2:00 e l’indice
▲ sotto il giorno 1 (lunedì) lampeggiano.
1 2 3 4 5
P3
= Temperatura comfort dalle ore
6h
alle
8h30
, dalle ore
11h30
alle
13h30
e dalle ore
16h30
alle
23h
.
Temperatura economia dalle ore
8h30
alle
11h30
, dalle ore
13h30
alle
16h30
e dalle ore
23h
alle
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7
+
☛
-
DAYS
☛
1-7
PROG
P1-P4
OK
0000
h
Res
Programmate l’ora con i tasti
+
/
-
(una pressione prolungata sul tasto accelera lo scorrimento dell’ora).
Regolare il giorno con pressioni successive sul tasto
DAYS 1-7
, un indice
▲ appare sotto il giorno corrispondente (1 = lunedì,2 = martedì,
3 = mercoledì, ecc.).
Convalidate con il tasto
OK
.
Se volete modificare l’ora o il giorno: premere sul tasto
MODE
fino alla comparsa dell’indice
▲ sotto la sigla orologio e procedere come indicato sopra, ai punti , e .
Regolazione delle temperature
Le temperature comfort e economia sono preregolate: Comfort = 20°C, Economia = 16°C.
☛ ☛
MODE
P4
=
Programma libero
che vi permette di creare 3 periodi in temperatura comfort e 3 periodi in temperatura economia per ogni giorno della settimana.
Selezione di un programma esistente P1,
P2 o P3 per un giorno della settimana (in modo programmazione tutte le modifiche si convalidano automaticamente).
esempio:
P2 per mercoledi
+
-
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
+
☛
-
Auto Manu
c
¡c c
¡c
1 2 3 4 5 6 7
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
Modifica della temperatura comfort
Premere sul tasto .
Modificare la temperatura con i tasti
+
/
-
.
Convalidate con il tasto
OK
.
Modifica della temperatura économique
Premere sul tasto .
Modificare la temperatura con i tasti
+
/
-
.
Convalidate con il tasto
OK
.
La programmazione
PROG
P1-P4
Per programmare la vostra settimana avete a disposizione 4 programmi:
P1
,
P2
,
P3
, che sono preregolati e non modificabili.
P4
che è libero e che permette di creare un programma personalizzato e differente per ogni giorno della settimana.
P1
= Temperatura comfort dalle ore
6h
alle
23h
.
Temperatura economia dalle ore
23h
alle
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
!
P1 è destinata ai 7 giorni della settimana in modo standard. Se P1 corrisponde al vostro ritmo di vita rimanete in modo automatico, in caso contrario continuate.
P2
= Temperatura comfort dalle ore
6h
alle
8h30
e dalle ore
16h30
alle
23h
.
Temperatura economia dalle ore
8h30
alle
16h30
e dalle ore
23h
alle
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Premere sul tasto
PROG P1-P4
per passare in modo programmazione.
Il numero del programma assegnato al giorno lampeggia sulla destra del display.
Premere sul tasto
DAYS 1-7
fino alla comparsa dell’indice
▲ sotto il giorno che volete programmare. Nel nostro caso : mercoledì.
Premere sul tasto
PROG P1-P4
fino alla comparsa a destra del display del numero di programma P2 che lampeggia.
Convalidate con il tasto
OK
, il giorno seguente
è proposto automaticamente.
Creazione di un programma
P4
Un profilo di 24 ore composto da 48 termometri in basso sul display vi permettono di visualizzare facilmente la composizione del vostro programma.
Un termometro mezzo vuoto corrisponde a
30 minuti a temperatura economia.
Un termometro pieno corrisponde a 30 minuti en temperatura comfort.
esempio:
creazione di 3 periodi in temperatura comfort per il venerdì: dalle
6h
alle
8h
, dalle
12h
alle
14h
e dalle
18h
alle
22h
.
1 2 3 4 5 6 7
+
-
Auto Manu
¡c
¡c
DAYS
1-7
2
☛
0
0
1
1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PROG
P1-P4
☛ ☛ ☛
0000
h
Res
☛ ☛
MODE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Partendo dal modo
Auto
, premere sul tasto
PROG P1-P4
.
Con il tasto
DAYS 1-7
selezionare il giorno da 1 a 7 e verificate la programmazione sul profilo di 24 ore sulla parte bassa del display (vedere esempio qui sotto).
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Premere su
MODE
per ritornare al modo
Auto
.
Il modo automatico (Auto)
Il passaggio in modo automatico si effettua premendo sul tasto
MODE
fino alla comparsa dell’indice
▲ sotto
Auto
.
MODE
In modo automatico il DIGI 2 HF si adatta al vostro ritmo di vita con il
Auto Manu
° c programma o con i programmi da voi scelti.
☛ ☛
Il modo manuale (Manu)
Il modo manuale trasforma il vostro apparecchio in un semplice termostato mantenendo una temperatura costante dell’ambiente (regolabile da 5 a 30° C).
6
Modifica temporanea della temperatura
In modo automatico, questa funzione molto pratica, vi permette di modificare temporaneamente la temperatura ambiente.
• Per aumentare la tempera-
Auto Manu
tura premere sul tasto
+
¡c
(più volte se necessario).
• Per abbassare la temperatura premere sul tasto
-
(più volte se necessario).
☛
☛
+
-
0 1
¡c
2 3 4 5
L’indicatore del livello di temperatura in corso
(comfort o economia), si mette a lampeggiare.
La modifica terminerà al prossimo cambio di temperatura programmato.
Per ritornare al programma iniziale premere su
MODE
e rimettere l’indice
▲ sotto
Auto
.
L’arresto del lampeggiamento del livello di temperatura (comfort o economico) indica la fine della modifica temporanea.
Il modo assenza prolungata
Vacanze
Questo modo mette la vostra abitazione al riparo da ogni rischio di gelo, pur mantenendo una temperatura minima regolabile durante la vostra assenza. Potete programmare la durata della vostra assenza per prevedere l’aumento della temperatura al vostro ritorno.
2 possibilità di fuori gelo:
Forzatura fuori gelo permanente
• Premere sul tasto , il giorno 0I si mette a lampeggiare.
• Premere una sola volta sul tasto
-
, la visualizzazione F
ORC si mette a lampeggiare.
• Convalidate con il tasto
OK
.
• Regolare il livello di temperatura desiderato durante la vostra assenza mediante i tasti
+
/
-
.
• Convalidate con il tasto
OK
.
Per annullare e ritornare in modo
Auto
, premere sul tasto
MODE
.
Impostazione fuori gelo per un determinato numero di giorni
• Premere sul tasto , il giorno 0I si mette a lampeggiare.
• Con i tasti
+
/
-
, regolate la durata della vostra assenza in giorni (da 1 a 99).
Il giorno in corso conta per 1
.
• Convalidate con il tasto
OK
.
• Regolare il livello di temperatura desiderato durante la vostra assenza mediante i tasti
+
/
-
.
• Convalidate con il tasto
OK
.
Per annullare e ritornare in modo
Auto
, premere sul tasto
MODE
.
Segnale di pausa della vostra
0000
installazione
h
Questo modo vi permette sia:
• di pensare di fare effettuare un periode di pausa
(cambio del filtro su un sistema ad aria condizionata o pulizia di un apparecchio).
• di paragonare il consumo del riscaldamento o dell’aria condizionata da un anno all’altro (confrontando il numero di ore di funzionamento).
Comptaggio del numero di ore di funzionamento
Auto Manu
1 2 3 4 5 6 7
+
timer
☛ ☛
MODE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
0000
OK
☛
h
Res
Premere sul tasto
0000 h il display indica, fin dalla installazione delle pile, il numero di ore di funzionamento del vostro bruciatore, sistema di climatizzazione, convettore ecc., a seconda del tipo di apparecchio ordinato (una pressione su
+
o
-
rimette il contatore a zero).
Premere su
MODE
per ritornare al modo
Auto
.
Programmazione del periodo di pausa della vostra installazione
Premere sul tasto
0000 h
.
Regolare con i tasti
+
/
-
le ore di funzionamento trascorse le quali volete che l’apparecchio vi avverta.
Convalidate con il tasto
OK
; Il conto alla rovescia ha inizio.L’apparizione del segno
timer
vi avvertirà della fine del conteggio.
Regolazioni eventuali
Potete procedere a differenti regolazioni sul retro dell’apparecchio (sempre che sia).
1-
Selezione del tipo d’installazione
■
Riscaldamento
■
Aria condizionamento
2- Selezione del modo di regolazione
■
On/Off
■
Cronoproporzionale
Il modo cronoproporzionale è più particolarmente indicato per installazioni di riscaldamento a pavimento (forte inerzia).
3-
Funzione antibloccaggio della pompa di circolazione (innesto della pompa per
1 minuto ogni 24 ore).
■
Arresto funzione antibloccaggio
■
Funzionamento funzione antibloccaggio
Configurazione
Per associare un emettitore con il ricevitore:
• Premere per più di 3 secondi il pulsante del ricevitore.
• La spia
OK
lampeggia, rilasciare il pulsante.
Questo è il modo configurazione.
• Premere per 3 secondi il pulsante
RESET
del
Thermoflash DIGI 2 HF.
• La spia
OK
del ricevitore non lampeggia più dopo circa 5 secondi.
Il collegamento emettitore/ricevitore è creato.
Reinizializzazione
Per cancellare tutti i collegamenti emettitore/ricevitore:
• Premere per oltre 10 secondi il pulsante del ricevitore.
• La spia
OK
si mette a lampeggiare lentamente, poi sempre più rapidamente.
• Premere di nuovo per 3 secondi il pulsante
memo
del ricevitore.
• La spia
OK
smette di lampeggiare, vengono cancellati tutti i collegamenti.
Il ricevitore torna in modo
Auto
.
Forzatura
Su questo apparecchio è disponibile un comando manuale:
• Premere brevemente il pulsante
memo
del ricevitore (pressione < 3 secondi).
Ogni volta che si preme brevemente il pulsante, viene invertito lo stato dell’uscita.
Osservazione:
il comando radio continua ad avere la precedenza.
7
Che cosa fare se… ?
•
Il riscaldamento non si avvia:
- il ricevitore non è alimentato: (spia
OK
spenta). Verificare il fusibile e l’interruttore automatico.
•
Il ricevitore è fuori dalla portata dell’emettitore:
- avvicinarsi sufficientemente al ricevitore.
•
Il ricevitore non riconosce il codice dell’emettitore:
- reinizializzare il ricevitore.
•
Il prodotto non si accende o non si spegne:
- il ricevitore o l'emettitore si trovano in un'area perturbata da altre onde (radio-amatori, televisione, antenne GSM ecc.): spostate il ricevitore o l'emettitore in un'altra zona non perturbata.
Se il problema persiste, contattare il proprio elettricista.
Caratteristiche tecniche
Emettitore
Intervallo di regolazione della T° comfort: da +5°C a +30°C
Intervallo di regolazione della T° ridotta: da +5°C a +30°C
Intervallo di regolazione della T° vacanze: da +5°C a +30°C
Intervallo di regolazione della T° ambiente:
Differenziale statico: da 0°C a +40°C
< 0.3°C
Alimentazione: 2 batterie alcaline tipo 1.5V LR6
(per alimentare il prodotto completo, trasmissione radio compresa)
Distanza di emissione: 75 metri con campo libero
3 piani in abitazione standard
Frequenza di emissione: 433.92 MHz
Funzionamento ciclo di emissione:
IP :
Temperatura di funzionamento:
Temperatura di stoccaggio:
10%
30
0°C a +40°C
-20°C a +70°C
Igrometria:
Livello di inquinamento:
Dimensioni:
Norme:
95% a 40°C normale
115 x 82 x 34 mm
EN 301-489-3
Ricevitore
Alimentazione:
Carica minima:
230 V +10 % a -15 %
12 V 100 mA
Uscita: 1 contatto invertitore libero da potenziale
Capacità d’interruzione:
AC1 :
Induttiva:
Frequenza radio:
Indice di protezione:
16 A 250 V
3 A (cos ϕ
= 0,6)
433.92 MHz
IP43
Classe d’isolamento:
Resistenza all’urto:
II
IK04
Temperatura di funzionamento: -10°C a +60°C
Temperatura di stoccaggio: -20°C a +70°C
Capacità flessibile:
Capacità rigida:
Dimensioni:
Igrometria:
Classe di ricezione
Norme:
0,5 a 1,5 mm 2
0,5 a 2,5 mm 2
130 x 60 x 27 mm
90% max. a 20°C
2
EN 60669-2-1
Norme:
EN 300220-3,
EN 301-489-1 e EN 301-489-3.
Usato in tutta Europa
Installazione del ricevitore
!
Prima di qualsiasi intervento, togliere corrente all’impianto. Lo schema dei collegamenti non raffigura le protezioni. L’installazione deve essere effettuata da un esperto nel rispetto delle norme in vigore.
Per facilitarne l’installazione, il kit Thermoflash
DIGI 2 HF viene fornito con un cavo flessibile dotato di 4 fili da 1,5 mm 2 , lunghezza 1,20 m (non collegato).
Per collegare il ricevitore HF, vi consigliamo di utilizzare questo cavo, rispettando i seguenti codici cromatici:
marrone
= fase
blu
= neutra
grigio nero
collegamento con la caldaia
L
N
5 4 3
L
2
N
1
L
N
5 4 3
L N
2 1
!
Nel caso di un collegamento con 2 tipi d’apparecchi (caldaia e climatizzazione), spegnere uno degli apparecchi afine di evitare che i due funzionano simultaneamente duranted la stessa staggione.
5 4 3
L
2
N
1
L
N
8
33 rue Saint-Nicolas
B.P. 50152 - 67704 SAVERNE Cedex
Tél. 03 88 01 88 01 - Fax 03 88 01 88 90 www.flash.fr
Kit Thermoflash DIGI 2 HF
Art. Nr. 56460
Digitale Uhrenthermostat drahtlos und aufputz Empfänger
Digitale Uhrenthermostat Wochenzyklus und IP43 aufputz Empfänger
FR IT
GB ES
DE
Produktbeschreibung
Der Uhrenthermostat DIGI 2 HF
Einfach zu installieren, leicht zu programmieren, der DIGI 2 HF Kit ermöglicht Ihnen ohne Bauarbeiten
Ihre Heizung zu programmieren und regulieren.
Komforttemperatur
Taste "+/–" für die Einstellung
Anzeige des
Temperaturwertes
für den
Komfort- und Absenkbetrieb
Absenktemperatur
+
-
Auto Manu
¡c
¡c
Anzeige des
Wochentags
Umgebungstemperatur
1 2 3 4 5 6 7 timer days
¡c
Anzeige für den Ladezustand der Batterie
MODE
Anzeige für die
Einschaltung der
Heizung oder der
Klimaanlage
Wahl der
Betriebsart
Längere
Abwesenheit
(Urlaub)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Anzeige der
Betriebsarten
Komfort- und
Absenkbetrieb
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Wahl des
Wochentags
(1 = Montag,
2 = Dienstag ...
7 = Sonntag)
Wahl des
Programms
P1 bis P4
Einstellung des Wertes der
Komforttemperatur
Einstellung des Wertes der
Bestätigung Einstellung des
Absenktemperatur Stundenzählers
RESET
Der DIGI 2 HF Kit ist entwickelt worden, um für Sie
Komfort und Energieeinsparen zu bieten.
Die Installation des DIGI 2 HF Kit in Ihre Wohnung ist leicht durchzuführen. Er reguliert, gemäss der
Programmierung, die Raumtemperatur und sendet
Ein/Aus Befehle dem Empfänger der in der Nähe des
Heizkessels installiert ist.
• Die Komforttemperatur: das ist die Temperatur, die Sie haben möchten, wenn Sie anwesend sind.
• Die Absenktemperatur: das ist die Temperatur, die
Sie während Ihrer kurzzeitigen Abwesenheit oder während der Nacht haben möchten.
• das ist die
Mindesttemperatur für die Zeit einer längeren
Abwesenheit. Mit dieser Einstellung ist Ihre Wohnung gegen Frost geschützt.
Einrichtung des Thermoflash DIGI 2 HF
Um die Regelung der Raumtemperatur zu sichern, sollte der DIGI 2 HF in ca. 1,5 m Höhe an einer
Stelle der Innenwand angebracht werden, die von direkter Sonneneinstrahlungen und anderen thermischen Einflüssen (bspw. Lampe, Fernseher, usw.) geschützt ist.
Sie können den DIGI 2 HF einfach auf ein
Möbelstück stellen, mit Hilfe des mitgelieferten
Sockels. Sie sollten dabei achten dass, kein
Außenfaktor den DIGI 2 HF beeinflussen kann
(Heizkörper, Fenster).
Sie können den DIGI 2 HF auch an die Wand befestigen.
• Den Sockel entfernen
IP43 Empfänger
Der IP43 Wandempfänger ist leicht und diskret in der Nähe des Heizkessels zu montieren.
Er erhält die Ein/Aus Befehle vom DIGI 2 HF und leitet sie mittels ein Schaltausgang an den
Heizkessel weiter.
Taste für Verknüpfung und Zwangbetrieb.
Betrieb- und Kodierungs-Kontrolleuchte.
Wenn die Leuchte an ist, steht das produkt unter Strohn.
LED blinkt = Kodierungsvorgang läuft.
Funktions-Kontrolleuchte.
LED leuchtet = Ausgangskontakt geschlossen =
ON.
!
Wichtig:
das Sende-/Empfangsgerät wird werkseitig mit dem Code versehen und ist daher sofort
Betriebsbereit.
Eine Codierung ist nicht erforderlich.
Einsetzen und Austausch der Batterien
Diese Uhrenthermostat besitzt eine Anzeige für den Ladezustand der Batterie. Sobald diese Anzeige unten rechts im Display erscheint, sollten Sie die Batterien auswechseln. Es sind jeweils 2 alkalische
Batterien 1,5 V LR 6 zu verwenden. Der Betrieb wird damit für ca. 12 Monate gewährleistet.
Beim Austausch der Batterien bleiben die Programme für 60 Sekunden im Gerät gespeichert.
Reset
Bevor Sie mit der Programmierung Ihres Gerätes beginnen, klappen Sie bitte die Haube herab und drücken Sie mit Hilfe der Spitze eines
Kugelschreibers o.ä. die Taste
RESET
.
0000
h
• An die Wand befestigen.
• Das Produkt auf den Sockel wieder montieren.
9
Einstellung des Tages und der
Uhrzeit
Es handelt sich um die erste Inbetriebnahme.
• Drücken Sie die Taste
1 2 3
RESET
.
• Die Anzeige I2:00 und der
Zeiger
▲ unterhalb des Tages
1 (Montag) blinken.
4 5
1 2 3 4 5 6 7
+
☛
-
DAYS
☛
1-7
PROG
P1-P4
OK
0000
h
Res
Stellen Sie nun mit den Tasten
+
/
-
die Uhrzeit ein. Beim anhaltenden Drücken dieser Tasten läuft die Zeitanzeige schneller durch.
Mit Hilfe der Taste
DAYS 1-7
, stellen Sie jetzt den Tag ein. Unter dem jeweiligen Tag erscheint dann der Zeiger
▲
(1 = Montag, 2 = Dienstag,
3 = Mittwoch usw.).
Bestätigen Sie die Einstellung mit der Taste
OK
.
Falls Sie die Einstellung des Tages oder der
Uhrzeit verändern möchten, drücken Sie die
Taste
MODE
bis der Zeiger
▲ unter dem Symbol der Uhr steht. Anschließend gehen Sie ebenso wie in den obigen Punkten , und vor.
Einstellung der Temperaturen
Die Werte der Komfort- und der
Absenktemperatur sind voreingestellt:
Komforttemperatur = 20°C,
Absenktemperatur = 16 C
1 2 3 4 5 6 7
-
Auto Manu
c
¡c c
¡c
MODE
☛ ☛
MODE
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Änderung der Komforttemperatur
Änderung der Taste .
Mit Hilfe der Taste
+
/
-
den Wert der Temperatur
ändern.
Bestätigen Sie die Einstellung mit der Taste
OK
.
Modification de la température économique
Änderung der Taste .
Mit Hilfe der Taste
+
/
-
den Wert der Temperatur
ändern.
+
/
-
.
Bestätigen Sie die Einstellung mit der Taste
OK
.
Programmierung
PROG
P1-P4
Für die Programmierung sind 4 Programme auswählbar:
P1
,
P2
,
P3
, sind voreingestellt und können nicht verändert werden.
P4
kann frei programmiert werden und erlaubt Ihnen damit, Ihr persönliches Programm für jeden einzelnen
Wochentag zu erstellen.
P2
= Komforttemperatur von
6 Uhr
bis
8.30
Uhr
und von
16.30 Uhr
bis
23 Uhr
.
Absenktemperatur von
8.30 Uhr
bis
16.30 Uhr
und von
23Uhr
bis
6 Uhr
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P3
= Komforttemperatur von
6 Uhr
bis
8.30
Uhr
und von
16.30 Uhr
bis
23 Uhr
.
Absenktemperatur von
8.30 Uhr
bis
11.30 Uhr
, von
13.30 Uhr
bis
16.30
Uhr
und von
23Uhr
bis
6 Uhr
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P4
= Über dieses
freie Programm
können
Sie für jeden einzelnen Wochentag bis zu 3 Zeiträume mit Komforttemperatur und 3 Zeiträume mit Absenktemperatur programmieren.
Wahl eines der voreingestellten Programme
P1, P2 und P3 für einen Wochentag (in dem
Betriebsmodus Programmierung werden alle Änderungen automatisch bestätigt).
Beispiel:
P2 für Mittwoch
+
-
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
MODE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Drücken Sie die Taste
PROG P1-P4
um in die
Betriebsart Programmierung zu gelangen.
Die Nummer des Programms, die dem
Wochentag zugeordnet ist,blinkt im rechten Teil des Displays.
Drücken Sie die Taste
DAYS 1-7
bis der Zeiger
▲ unter dem Wochentag steht, den Sie programmieren möchten (in unserem Beispiel :
Mittwoch).
Drücken Sie die Taste
PROG P1-P4
zu drücken, bis im rechten Teil des Displays die gewünschte Programmnummer P2 blinkt.
Bestätigen Sie die Einstellung mit der Taste
OK
, anschliessend wird Ihnen automatisch der folgende
Tag angeboten.
Zusammenstellung eines Programms
P4
1 2 3 4 5 6 7
+
-
Auto Manu
¡c
¡c
DAYS
1-7
2
☛
0
0
1
1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
PROG
P1-P4
☛ ☛ ☛
0000
h
Res
☛ ☛
MODE
P1
= Komforttemperatur von
6 Uhr
bis
23 Uhr
.
Absenktemperatur von
23 Uhr
à
6h
.
Im unteren Teil des Displays wird ein aus 48
Thermometern bestehendes 24 Std.Profil angezeigt, an dem Sie die Zusammensetzung Ihres Programms ganz deutlich ablesen können.
Ein halbleeres Thermometer entspricht
30 Minuten bei Absenktemperatur.
Ein volles Thermometer entspricht 30 Minuten bei Komforttemperatur.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
!
P1 ist standardmässig den 7 Wochentagen zugeordnet. Sollte dieses Programm Ihrem
Lebensrhythmus entsprechen, so bleiben
Sie in dem automatischen Betriebsmodus, sonst setzen Sie fort.
Beispiel:
für die Programmierung von 3 Perioden bei
Komforttemperatur für Freitag:
6 Uhr
bis
8 Uhr
,
12
Uhr
bis
14 Uhr
und
18 Uhr
bis
22 Uhr
.
Ausgehend von der Betriebsart
Auto
, drücken
Sie die Taste
PROG P1-P4
.
Drücken Sie die Taste
DAYS 1-7
bis sich der
Zeiger
▲ unter dem Tage befindet, den Sie programmieren möchten,das ist in unserem Falle der
Freitag.
Drücken Sie die Taste
PROG P1-P4
bis im rechten Teil des Displays die Programmnummer
P4 blinkt. Ihr Display zeigt 0:00 an und das erste
Thermometer im Profil der 24 Std blinkt.
Jetzt drücken Sie mehrmals die Taste bis die Zeit 6:00 angezeigt wird. Bei jedem kurzen
Druck rücken Sie um 30 Minuten vor.Durch ein anhaltendes Drücken der Taste wird das
Durchlaufen der Uhrzeit beschleunigt.
bis die Zeit • Drücken Sie mehrmals die Taste
8:00 Uhr angezeigt wird.
• Drücken Sie mehrmals die Taste
I2:00 Uhr angezeigt wird.
• Drücken Sie mehrmals die Taste
I4:00 Uhr angezeigt wird.
• Drücken Sie mehrmals die Taste
I8:00 Uhr angezeigt wird.
• Drücken Sie mehrmals die Taste
22:00 Uhr angezeigt wird.
bis die Zeit bis die Zeit bis die Zeit bis die Zeit
Anmerkung:
sollten Sie einen Fehler gemacht haben (z.B. 11.30 Uhr statt 12.00 Uhr), so benutzen
Sie die Tasten
+
/
-
um sich vor- oder rückwärts zu bewegen und dann mit Hilfe der Tasten die entsprechenden Korrekturen vorzunehmen.
Bestätigen Sie die Einstellung mit der Taste
OK
, anschliessend wird Ihnen automatisch der folgende
Tag angeboten.
Drücken Sie die Taste
MODE
um in die
Auto
Betriebsmodus zurückzukehren.
Ablesen der Programme
Sie können Ihre Programmierung folgenderweise
überprüfen:
+
-
1 2 3 4 5 6 7
Auto Manu
¡c
¡c
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
☛ ☛
MODE
Ausgehend von der Betriebsart
Auto
, drücken
Sie die Taste
PROG P1-P4
.
Jetzt drücken Sie die Taste
DAYS 1-7
um den Tag auszuwählen. Anschliessend können Sie die
Programmierung an dem Profil der 24 Std überprüfen, das im unteren Teil des Displays angezeigt wird, z.B.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Zum Schluss drücken Sie die Taste
MODE
um in den
Auto
Betriebsmodus zurückzukehren.
Automatischer Betriebsmodus
(Auto)
Um den automatischen Betriebsmodus einzuschalten, ist die Taste
MODE
zu drücken, bis der Zeiger
▲ unter
Auto
steht.
MODE
Auto Manu
In dem automatischen Betriebsmodus
° c passt sich dieser Uhrenthermostat
Ihrem Lebensrhythmus an, indem das von Ihnen
☛ ☛ gewählte Programm ausgeführt wird.
10
Handgesteuerter Betriebsmodus
(Manu)
In dem handgesteuerten Betriebsmodus wird Ihr
Gerät zu einem einfachen Thermostaten.
Sie können auf diese Weise in Ihrer Wohnung eine konstante Temperatur aufrecht erhalten (die Sie von
5 °C bis 30 °C einstellen können).
Verknüpfung
¡c ¡c
☛
☛
☛
+
-
☛
DAYS
1-7
PROG
P1-P4
¡c
☛ ☛
MODE
OK
0000
h
Res
Drücken Sie die Taste
MODE
um den Zeiger
▲ unter
Manu
zu setzen.
Drücken Sie die Tasten
+
oder
-
um die gewünschte
Temperatur einzustellen (z.B. 22,5 °C).
Um die
Manu
zu verlassen, drücken Sie erneut die
Taste
MODE
um den Zeiger
▲ unter
Auto
zu setzen.
Vorübergehende Änderung der
Temperatur
In dem automatischen Betriebsmodus, können Sie
über diese sehr praktische Funktion die
Umgebungstemperatur zeitweilig ändern.
• Um die Temperatur zu erhöhen, drücken Sie
(gegebenenfalls mehrfach) die Taste
+
.
• Um die Temperatur zu senken, drücken Sie
☛
☛
+
-
(gegebenenfalls mehrfach) die Taste
-
.
Auto Manu
0 1
¡c
¡c
2 3 4 5
Die Anzeige des aktuellen Sollwertes der
Temperatur (Absenk- oder Komforttemperatur) beginnt zu blinken. Diese Änderung wird mit dem nächsten programmierten Temperaturwechsel aufgehoben.
Um zum ursprünglichen Programm zurückzukehren, ist die Taste
MODE
zu drücken, bis der Zeiger
▲ unter
Auto
steht.
Das Ende der zeitweiligen Änderung der
Temperatur wird dadurch gekennzeichnet, dass die
Anzeige des aktuellen Sollwertes der Temperatur
(Absenk- oder Komforttemperatur) aufhört zu blinken.
Urlaubsbetriebsmodus
(bei längerer Abwesenheit)
In diesem Betriebsmodus wird Ihre Wohnung während einer längeren Abwesenheit gegen Frost geschützt, indem hier eine einstellbare Mindesttemperatur aufrechterhalten wird. Sie können die Dauer Ihrer
Abwesenheit programmieren, um für ihre Rückkehr einen Temperaturanstieg in Ihrer Wohnung vorzusehen.
2 Möglichkeiten für die Frostschutzschaltung
Permanenter Frostschutz (Zwangsbetrieb)
• Drücken Sie die Taste Wochentag 0I blinkt.
• Drücken Sie einmal die Taste
-
, Anzeige F
ORC
(Zwangsbetrieb) blinkt.
• Bestätigen Sie die Einstellung mit der Taste
OK
.
• Jetzt den während Ihrer Abwesenheit gewünschten
Temperaturlevel mit Hilfe der Tasten
+
/
-
eingeben.
• Bestätigen Sie die Einstellung mit der Taste
OK
.
Um in
Auto
Betriebsmodus zurückzukehren und um abzubrechen, drücken Sie die Taste
MODE
.
Frostschutzbetrieb über mehrere Tage
• Drücken Sie die Taste Wochentag 0I blinkt
• Stellen Sie mit den tasten
+
/
-
, die Anzahl der
Tage ihrer Abwesenheit ein (1 bis 99 Tage).
Der laufende Tage gilt dabei als 1.
• Bestätigen Sie die Einstellung mit der Taste
OK
.
• Jetzt den während Ihrer Abwesenheit gewünschten
Temperaturlevel mit Hilfe der Tasten
+
/
-
eingeben.
• Bestätigen Sie die Einstellung mit der Taste
OK
.
Um in
Auto
Betriebsmodus zurückzukehren und um abzubrechen, drücken Sie die Taste
MODE
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
☛
h
Res
Nachdem Sie die Taste
0000 h gedrückt haben,wird
Ihnen auf dem Display die Anzahl der
Betriebsstunden seit dem Einsetzen der Batterien angezeigt, d.h. die Anzahl der Stunden, in denen
Ihr Brenner,Ihre Klimaanlage,Ihr Heizlüfter oder ein anderes Gerät, das Sie angeschlossen haben, eingeschaltet war. (der Taste
+
oder
-
wird der
Zähler auf Null gesetzt).
Drücken Sie die Taste
MODE
um in die
Auto
Betriebsweise zurückzukehren.
Programmierung des Wartungsintervalls für ihre Anlage
Drücken Sie die Taste
0000 h
.
Stellen Sie mit den Tasten
+
/
-
die Anzahl der
Betriebsstunden ein,nach denen Sie hingewiesen werden möchten.
Bestätigen Sie die Einstellung mit der Taste
OK
;
Das Rückwärtszählen beginnt. Am Ende des
Zählvorgangs werden sie durch die Anzeige des
Zeichens
timer
hingewiesen.
Mögliche Einstellungen
An der Rückseite Ihres nicht aufgesetzten Vorteils können Sie unterschiedliche Einstellungen vornehmen:
1- Anlagestypsauswahl
■
Heizung
■
2- Regelungstypsauswahl
Klimaanlage
■
Ein/Aus
■
Zeitproportional
Der Zeitproportionale Modus ist für
Fussbodenheizungen empfohlen.
3-
Blockierschutzfunktion für die
Umwälzpumpe (Einschalten der Pumpe für 1 Minute nach jeweils 24 Stunden)
■
Blockierschutz
Aus
■
Blockierschutz
Ein
Um ein Sender mit einem Empfänger zu verknüpfen:
• Taste des Empfängers 3 Sekunden drücken.
• Die Kontrolleuchte
OK
blinkt, Taste loschen. Sie sind jetzt im Konfigurationsmodus.
• Die Taste
RESET
des Thermoflash DIGI 2 HF, 3
Sekunden lang, drückten.
• Kontrolleuchte
OK
hört auf zu blinken nach ungefähr 5 Sekunden.
Die Verknüpfung zwischen Sender und Empfänger ist jetzt erstellt.
Zurücksetzen
Löschen sämtlicher Sender-/Empfänger Verknüpfungen:
• Taste des Empfängers mindestens 10
Sekunden lang drücken.
• Kontrolleuchte
OK
blinkt erst langsam, dann schnell.
• Erneut 3 Sekunden lang die Taste des
Empfängers drücken.
• Kontrolleuchte
OK
hört auf zu blinken, sämtliche Verknüpfungen sind gelöscht.
Der Empfänger kehrt in den automatischen
Betriebsmodus zurück.
Zwangsbetrieb
Das Gerät kann im Handbetrieb gesteuert werden:
• Drücken Sie kurz die Taste des Empfängers
(Duck < 3 Sek.).
Jeder kurze Druck kehrt den Ausgangszustand um.
Hinweis:
die Funksteuerung behält immer den
Vorrang auf der Handbedienung.
Was tun wenn?
•
Die Heizung schaltet sich nicht ein:
- der Empfänger steht nicht unter Spannung
(Kontrolleuchte
OK
leuchtet nicht).
Sicherung und Leistungsschutzschalter überprüfen.
•
Der Empfänger befindet sich nicht in
Senderreichweite:
- gehen Sie nahe genug an den Empfänger heran.
•
Der Empfänger erkennt nicht den Kode vom Sender:
- den Empfänger neu kodifizieren.
•
Die Anwendung schaltet sich nicht ein oder schaltet sich nicht aus:
Störsignale gestört (CB-Funk,
Fernsehbildschirm, Handy-Signalverstärker usw.): versuchen Sie die Quelle der Störsignale in grösserer Entfernung aufzustellen.
Sollte das Problem anhalten, wenden Sie sich an
Ihren Elektriker.
11
Anschlüss des Empfängers
!
Das Anschlußbild zeigt die Schutzelemente nicht. Die Einrichtung sollte fachgemäss und normgerecht durchgeführt werden.
Um die Installation zu erleichtern wird der
Bausatz Thermoflash DIGI 2 HF mit einem flexiblen Kabel, 4-adrig, Querschnittsfläche 1,5 mm 2 ,
Länge 1,20 m geliefert (nicht angeschlossen).
Wir empfehlen Ihnen, den HF-Empfänger mit Hilfe dieses Kabels unter Beachtung des nachstehenden
Farbencodes anzuschließen:
braun
= Phase
blau
= nulleiter
grau schwartz
Anbindung an Heizkessel
Technische Daten
Sender
Einstellbereich für die Normaltemperatur:
+5°C bis +30°C
Einstellbereich für die Absenktemperatur:
+5°C bis +30°C
Einstellbereich für die Frostschutztemperatur:
+5°C bis +30°C
Anzeigebereich für die Raumtemperatur:
Statische Schaltdifferenz:
0°C bis +40°C
< 0.3°C
Stromversorgung: 2 Batterien typ LR6
(Produkt inklusive Funkübertragung)
Durchschnittliche Reichweite: 75 m. zwischen
Sender und Empfänger im Freifeld
Übertragung über 3 Stockwerke im Wohnbereich
Sendefrequenz: 433.92 MHz
Duty cycle:
IP :
Betriebstemperatur:
Lagertemperatur:
10%
30
0°C bis +40°C
-20°C bis +70°C
Luftfeuchtigkeit:
Verschmutzungstufe:
Abmessungen:
Normen:
95% bis 40°C normal
115 x 82 x 34 mm
EN 301-489-3
Emfänger
Versorgungsspannung: 230 V +10 % bis -15 %
Mindestlast:
Ausgang:
Schaltleistung:
12 V 100 mA
1 Wechselkontakt, spannungsfrei
AC1:
Induktiv:
Funkfrequenz:
Schutzgrad:
16 A 250 V
3 A (cos ϕ
= 0,6)
433.92 MHz
IP43
Schutzklasse:
Stossfestigkeit
Betriebstemperatur:
Lagerungstemperatur:
Flexibel:
Massiv:
Abmessungen:
Luftfeuchtigkeit:
Receiver class:
Normen:
II
IK04
-10°C bis +60°C
-20°C bis +70°C
0,5 bis 1,5 mm 2
0,5 bis 2,5 mm 2
130 x 60 x 27 mm
90% max. bei 20°C
2
EN 60669-2-1
Normen:
EN 300220-3,
EN 301-489-1 und EN 301-489-3.
L
N
5 4 3
L N
2 1
!
Falls Sie den Thermoflash DIGI 2 HF für
Heizung und Kühlung Steuerung verwenden, müssen Sie achten, dass beide Systeme
(Heizung und Kühlung) nicht während der selbe jahreszeit funktionnieren.
L
N
5 4 3
L
2
N
1
L
N
5 4 3
L
2
N
1
Überall in Europa einsetzbar
12
33 rue Saint-Nicolas
B.P. 50152 - 67704 SAVERNE Cedex
Tél. 03 88 01 88 01 - Fax 03 88 01 88 90 www.flash.fr
Kit Thermoflash DIGI 2 HF
ref. 56460
Wireless clock thermostat and wall-mounting receiver
The Thermoflash DIGI 2 HF kit has been designed to offer you comfort and energy savings. It will be easily installed in your home and will control the ambient temperature according to the program. It will control through radio waves the RF receiver which may be fitted close to the boiler or the heating system.
The Thermoflash DIGI 2 HF kit will control the ambient temperature according to 3 temperature levels.
• Comfort temperature: this is the temperature for your hours of presence.
• Reduced temperature: this is the temperature for your brief absences or during the night.
• Frost protection temperature: this is the minimum temperature for long absences. It protects your dwelling from the risk of frost.
Wireless clock thermostat, weekly cycle and
IP43 wall-mounting receiver
FR IT
GB ES
DE
Product presentation
The thermostat DIGI 2 HF
Easy to install, easy to program, the kit DIGI 2 HF will allow you to control your heating system in accordance with your way of life.
Comfort temperature
+/– buttons for adjusting settings
Indicator for current temperature level comfort or reduced
Reduced temperature
+
-
Auto Manu
¡c
¡c
Pointer indicating day of the week
Ambient temperature
1 2 3 4 5 6 7 timer days
¡c
Warning light to indicate battery wear
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MODE
Heating or air conditioning start-up indicator
Mode selection
Prolonged absence
(holidays)
Viewing of comfort and economical periods
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Installation of thermoflash DIGI 2 HF
To control accurately the ambient temperature, the DIGI 2 HF must be installed 1,5 m. above the floor, on an internal wall shaded from direct sunlight and from all thermal influences such as: television, lamps, heater, etc.
The DIGI 2 HF is delivered with a base.With this accessory, you can simply put it on a furniture. It is important to check that no external influence will perturb it (heater, window etc.).
RESET Days of the week selection
(1=Monday, 2=Tuesday....
7=Sunday)
P1 to P4 programme selection
Comfort temperature setting
Reduced temperature setting
Validation Hour counter setting
You can also install it on an internal wall.
• Therefore, take out its wall mounting base.
The IP43 wall-mounting receiver
The IP43 wall-mounting receiver can be easily installed close to the boiler.The thermostat DIGI 2 HF will control the ambient temperature in the dwelling and will transmit ON and OFF signals to the receiver.
Pushbutton for configuration and priority setting.
Indicator of Power on and coding light.
LED on = product is powered on.
This LED flickers during coding operations.
Operation indicator light.
The LED is on when receiver’s output contact is closed = ON.
!
Important:
the transmitter and receiver assembly is factory coded and is therefore immediately operational.
There is no need to recode.
Inserting or re-inserting the batteries
This clock thermostat is equipped with a warning light to indicate when the batteries need replacing.
As soon as this indicator lights up at the bottom right-hand side of the display panel, replace the batteries (use two 1.5V LR6 alkaline batteries, life is approximately 12 months).
The device remains programmed for 60 seconds while batteries are being replaced.
Reset
Before beginning the programming of the device, please slide cover down and press
RESET
with the tip of a pen.
0000
h
• Fix it to the wall.
• Then replace the product on its base.
13
Setting current time and day
You are putting the device into operation for the first time.
• You have just pressed the
1 2 3 4 5
RESET
button.
• I2:00 appears and the pointer
▲ flashes under day 1 (monday).
1 2 3 4 5 6 7
+
☛
-
☛ ☛
MODE
DAYS
☛
1-7
PROG
P1-P4
OK
0000
h
Res
Set the time using the
+
/
-
buttons (the numbers run off more quickly when the button is pressed continuously).
Set the current day by pressing several times on the
DAYS 1-7
, a pointer
▲ appears under the corresponding day (1=monday, 2=tuesday,
3=wednesday, etc.)
Validate with the
OK
button.
If you wish to change the time or the day, press the
MODE
button until the pointer
▲ under the clock sign and continue as above for points , and .
Temperature setting
Comfort and reduced temperatures are pre-set:
Comfort = 20°C, Reduced = 16°C.
P3
= Comfort temperature from
6 a.m.
till
8.30
a.m.
, from
11.30 a.m.
till
1.30 p.m.
and from
4.30 p.m.
till
11 p.m.
Reduced temperature from
8.30 a.m.
till
11.30 a.m.
from
1.30 a.m.
till
4.30 p.m.
and from
11 p.m.
till
6 a.m.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P4
=
Blank programme
allowing you to create 3 comfort temperature periods and 3 reduced periods for each day of the week.
Selection of an existing P1, P2 or P3 programme for a day of the week (in programming mode all modifications are automatically validated).
example :
P2 for wednesday
+
-
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
Press the button several times to obtain
6:00 :The time displayed advances by 30 minutes for each short press. Continuous pressing accelerates the time run-off.
• Press the
8:00 .
• Press the
I2:00 .
• Press the
I4:00 .
• Press the
I8:00 .
• Press the
22:00 .
button several times to obtain button several times to obtain button several times to obtain button several times to obtain button several times to obtain
N.B. :
if you make a mistake (e.g. 11.30 instead of
12.00) use the
+
/
-
buttons to advance or return and correct with the thermometer buttons.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
-
Auto Manu
c
¡c c
¡c
1 2 3 4 5 6 7
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
MODE
Modification of comfort temperature
Press the button.
Modify the temperature with the
+
/
-
buttons.
Validate with the
OK
button.
Modification of reduced temperature
Press the button.
Modify the temperature with the
+
/
-
buttons.
Validate with the
OK
button.
Programming
PROG
P1-P4
You can programme your week according to 4 programme settings:
P1
,
P2
and
P3
are pre-recorded and cannot be modified.
P4
is blank and allows you to create a personalized programme varying according to the day of the week.
P1
= Comfort temperature from
6 a.m.
till
11 p.m.
Reduced temperature from
11 p.m.
till
6 a.m.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
!
The default allocation of P1 is to 7 days of the week. If this corresponds to your life style, stay in automatic mode, otherwise, continue.
P2
= Comfort temperature from
6 a.m.
till
8.30
a.m.
and from
4.30 p.m.
till
11 p.m.
Reduced temperature from
8.30 a.m.
till
4.30 p.m.
and from
11 p.m.
till
6 a.m.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
From the
Auto
,mode press the
PROG P1-P4
button.
Press the
DAYS 1-7
button until a pointer
▲ appears under the day you wish to programme
(friday in our example).
Press the
PROG P1-P4
button until the P4 programme number flashes in the right side of the screen.Your display panel indicates time as
0:00 and the first thermometer flashes on the
24-hour profile.
Press the
MODE
button to position the pointer
▲ under
Manu
.
Press the
+
or
-
buttons to adjust to the desired temperature (for instance 22.5°C).
To quit the
Manu
mode, press the
MODE
button and re-position
▲ under
Auto
.
14
Temporary temperature modification
In automatic mode this very useful function allows you to modify ambient temperature temporarily.
• To increase the temperature, press the
+
button
(several times, if necessary).
Auto Manu
• To decrease the temperature
☛
+
-
☛
¡c press the
-
button (several times, if necessary).
The current temperature level
☛
☛
0 1
¡c
2 3
indicator (comfort or reduced) will begin flashing.
4 5
This modification ends with the next change in programmed temperature.
To return to the initial programme press
MODE
and re-position the pointer
▲ under
Auto
.
The current temperature level indicator (comfort or reduced) will stop flashing when the temporary modification comes to an end.
Prolonged absence mode
(holidays)
This mode protects your dwelling from freezing by maintaining a minimum adjustable temperature in your dwelling during your absences.
You can programme the length of your absence so that the temperature rises for your return.
2 different settings are available for maintaining temperature above frost level:
Permanent frost protection
• Press the button, the day 0I flickers.
• Press once the
-
button, the F
ORC display flickers.
• Validate with the
OK
button.
• Using
+
/
-
buttons, set the temperature level desired during your absence.
• Validate with the
OK
button.
To cancel and return to
Auto
mode, press
MODE
button.
Setting frost protection temperature for a certain number of days
• Press the button, the day 0I flickers.
• Using
+
/
-
buttons, set the length of your absence in days (from 1 to 99 days).
The current day count as one.
• Validate with the
OK
button.
• Using
+
/
-
buttons, set the temperature level desired during your absence.
• Validate with the
OK
button.
To cancel and return to
Auto
mode, press
MODE
button.
Installation maintenance signal
0000 h
This mode allows you either:
• to take steps for regular maintenance (change of air conditioning filter, device cleaning).
• to compare your heating or air conditioning consumption from one year to the next (by comparing the number of running hours).
Counting running hours
+
-
Auto Manu
1 2 3 4 5 6 7 timer
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
☛
h
Res
Press the
0000 h button. The display panel will ndicate the number of hours your burner, air conditioning,ventilator-convector,etc.(depending of the type of device controlled) has been running from the moment the batteries were inserted (by pressing once on
+
or
-
you return the counter to zero.).
Press the
MODE
button to return in
Auto
mode.
☛ ☛
MODE
Programming the regular servicing of your installation.
Press the
0000 h button.
Set the number of running hours after which the warning signal should flash using the
+
/
-
buttons.
Validate with the
OK
button; the countdown begins.The message
timer
will appear at the end of the count-down warning you that servicing is required.
Possible settings
Various settings can be made on the back of the device (when it is not mounted).
Troubleshootings
•
The heating does not start:
- receiver’s power supply is cut off (
OK
light is off). Check fuse and circuit breaker.
•
Receiver is outside of transmitter’s range:
- move transmitter closer to receiver.
•
Receiver does not recognize transmitter’s code:
- re-install receiver.
•
The system does not start or does not stop:
- the receiver or transmitter is disturbed by radio transmission (radio ham, TV monitor, cellular phone re-transmitter, etc.): attempt to remove the source of disturbance.
In case of persistent problem, call on your electrician.
1-
Selection of installation’s type
■
Heating
■
On/Off
Configuration
■
Cooling
2- Selection of adjustment mode
■
Proportionnal
The proportionnal mode is to be set when using floorheating (high inertia).
3- Anti-locking function for the circulation pump (activation of the pump for 1 minute every 24 hours)
■
Anti-locking Anti-locking function off
■ function on
In order to associate the transmitter with the receiver:
• Press the receiver’s pushbutton for more than 3 seconds.
• The indicator
OK
light will start flickering, release the pushbutton.
The system is in configuration mode.
• Press the
RESET
button during 3 seconds of the transmitter Thermoflash DIGI 2 HF.
• The indicator
OK
button will stop flickering, at the end of 5 secondes.
The transmitter/receiver link is now established.
Technical specifications
Transmitter
Adjustment range for comfort temperature:
+5°C to +30°C
Adjustment range for reduced temperature:
+5°C to +30°C
Adjustment range for frost protection temperature:
+5°C to +30°C
Display range for ambient temperature:
Static differential:
0°C to +40°C
< 0.3 K
Power: 2 standard LR6 alkaline batteries
(to supply the product and the radio transmission)
Operating range: 75 m from transmitter to receiver in a free field (operates over 3 building floors)
Transmission frequence:
Transmitter duty cycle:
433.92 MHz
10%
IP:
Operating temperature:
Storage temperature:
Hygrometry:
Dimensions:
Degree of pollution:
Standards:
30
0°C to +40°C
–20°C to +70°C
95% max. at 25°C
115 x 82 x 34 mm standard
EN 301-489-3
Receiver
Supply voltage: 230 V +10 % at -15 %
Minimum load: 12 V 100 mA
Output: 1 changeover contact free of potential
Switching capacity:
AC1:
Inductive:
Radio frequency:
16 A 250 V
3 A (cos ϕ
= 0,6)
433.92 MHz
Degree of protection:
Isolation class:
Mechanical protection:
Operating temperature:
Storage temperature:
Flexible capacity:
Rigid capacity
Dimensions:
Hygrometry:
Receiver class:
Standards:
IP43
II
IK04
-10°C to +60°C
-20°C to +70°C
0,5 to 1,5 mm 2
0,5 to 2,5 mm 2
130 x 60 x 27 mm
90% max. at 20°C
2
EN 60669-2-1
Standards:
EN 300220-3,
EN 301-489-1 and EN 301-489-3.
Reset
For clearing all transmission/reception links:
• Press the receiver’s pushbutton for more than 10 seconds.
• The indicator
OK
light flickers slowly, then more quickly.
• Press again the receiver’s pushbutton more than 3 seconds.
• The indicator
OK
light stops flickering, all links have been cleared.
The receiver returns to the
Auto
mode.
Priority setting
Manual control is provided for this product.
• Press shortly receiver’s pushbutton (<3 sec).
Each press reverses output state.
Note:
radio control retains priority.
Usable everywhere in Europe
15
Receiver installation
!
Before working on the installation, isolate all electrical supplies. All electrical wiring must be carried out by a qualified person.
For easier installation, the Thermoflash DIGI 2 HF kit is suppplied with a flexible 4-wire 1,5 mm 2 cable of 1.20m length (not connected).
We recommend using this cable for connecting the
HF receiver according to the following colour codes:
brown
= phase
blue
= neutral
gray
connection to the boiler
black
L
N
5 4 3
L
2
N
1
L
N
5 4 3
L N
2 1
!
When two appliances (heating and cooling) are connected, always keep one of them switched off to prevent their simultaneous operation during the same season.
5 4 3
L
2
N
1
L
N
16
33 rue Saint-Nicolas
B.P. 50152 - 67704 SAVERNE Cedex
Tél. 03 88 01 88 01 - Fax 03 88 01 88 90 www.flash.fr
Kit Thermoflash DIGI 2 HF
ref. 56460
Termostato programable y receptor mural
El Kit DIGI 2 HF ha sido creado para aportar confort y ahorro de energía. De fácil instalación en su vivienda, regula la temperatura ambiente en función de la programación y envía órdenes de marcha/paro al receptor mural instalado cerca de la caldera.
El Kit DIGI 2 HF regula la temperatura ambiente según 3 niveles de temperatura.
durante su estancia.
durante las ausencias diarias, o por la noche.
• Temperatura descarche: temperatura mínima asegurada durante sus ausencias prolongadas.
Protege su hogar de las heladas.
Termostato programable sin hilos, ciclo semanal y receptor mural IP43
FR IT
GB ES
DE
Presentación de los productos
El termostato DIGI 2 HF
Simple de instalar, fácil de programar, el Kit DIGI 2 HF sin problemas para programar y regular su calefacción.
Temperatura económica
Temperatura confort
Teclas +/– para las regulaciones
Indicador del nivel de temperatura actual confort o económica
+
-
Auto Manu
Indicador del día de la semana
Temperatura ambiente
Testigo de desgaste de las pilas
Indicador de puesta en marcha de la calefacción o de la climatización
1 2 3 4 5 6 7
Selección de los modos
¡c
¡c timer days
MODE
Ausencia prolongada
(vacaciones)
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Visualización de los periodos confort y económico
Instalación del termostato DIGI 2 HF
Para asegurar el correcto funcionamiento de regulación de la temperatura ambiente el DIGI 2 HF debe instalarse a un altura de 1,5 m del suelo, en una pared interior y alejado de cualquier fuente de calor directo como: televisión, lámparas, radiadores, corrientes de aire etc.
Con ayuda del zócalo que acompaña al DIGI 2 HF, puede colocarlo simplemente sobre cualquier mueble, lejos de la influencia de cualquier factor externo (radiador, ventana).
Selección de los días de la semana
(1 = lunes, 2 = martes, ...,
7 = domingo)
Elección del programa de P1 a P4
Regulación temperatura confort
Regulación temperatura económica
Validación Regulación cómputo horario
Puesta a cero general
Puede fijarlo a la pared.
• Para ello quitar el zócalo trasero.
El receptor mural IP 43
El receptor mural IP 43, se instala fácilmente cerca de la caldera. El DIGI 2 HF manda las órdenes de marcha/paro al IP 43 y este las trasmite a la caldera.
Pulsador para configuración y forzamiento.
Indicador de puesta en tensión y de codificación.
Led encendido = el aparato recibe tensión.
Este led parpadea durante las operaciones de codificación.
Indicador de funcionamiento.
Este led está encendido cuando el contacto de salida del receptor está cerrado = ON.
• Fijarlo a la pared.
!
Importante:
el equipo emisor + receptor sale codificado de fábrica, apto listo para su funcionamiento.
Superfluo de recodificar.
Colocación o cambio de las pilas
El Cronotermostato dispone de un testigo de desgaste de las pilas. Cuando éste se enciende en la parte derecha del visualizador, hay que cambiar las pilas (utilice 2 pilas de 1,5 V, alcalinas LR6 - su autonomía es de unos 12 meses).
Cuando se cambian las pilas, el cronotermostato mantiene sus programas durante 60 segundos.
Reinicialización
Antes de iniciar la programación de su aparato, baje la tapa y pulse la tecla
RESET
con la punta de un bolígrafo.
0000
h
• Volver a colocar el DIGI 2 HF sobre su zócalo.
17
Puesta en hora y fecha
Es la primera puesta en servicio.
• Acaba de pulsar la tecla
RESET
.
• Las inscripciones I2:00 y el apuntador s bajo el día 1
(lunes) se encienden intermitentemente.
1 2 3 4 5
+
☛
-
DAYS
☛
1-7
PROG
P1-P4
0000
h
Res
Ponga la hora con las teclas
+
/
-
(si pulsa la tecla de forma prolongada, se acelera el paso de la hora).
Ajuste la fecha actual pulsando sucesivamente la tecla
DAYS 1-7
,aparece un apuntador
▲ bajo el día correspondiente (1 = lunes, 2 = martes,
3 = miércoles, etc.).
Valide con la tecla
OK
.
Si desea modificar la hora o el día, pulse la tecla
MODE
hasta que aparezca el apuntador
▲ bajo la sigla reloj,y proceda como en los puntos , y .
Regulación de las temperaturas
Auto Manu
c
¡c c
¡c
1 2 3 4 5 6 7
DAYS
1-7
PROG
P1-P4
1 2 3 4 5 6 7
OK
OK
0000
h
Res
Modificación de la temperatura confort
Pulse la tecla .
Modifique la temperatura con las teclas
+
/
-
.
Valide con la tecla
OK
.
Modificación de la temperatura económica
Pulse la tecla .
Modifique la temperatura con las teclas
+
/
-
.
Valide con la tecla
OK
.
Programación
PROG
P1-P4
Para programar su semana, dispone de 4 programas
P1
,
P2
,
P3
, que están prerregistrados y no son modificables.
P4
que es libre, y le permite crear un programa personalizado y diferente para cada día de la semana.
P1
= Temperatura confort de
6h
a
23h
.
Temperatura económica de
23h
a
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
!
P1 está asignado a los 7 días de la semana de forma estándar. Si corresponde a su ritmo de vida, manténgase en modo automático; de lo contrario, continúe.
P2
= Temperatura confort de
6h
à
8h30
y de
16h30
a
23h
.
Temperatura económica de
8h30
a
16h30
y de
23h
a
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
☛ ☛
MODE
Las temperaturas confort y económica están preajustadas: Confort = 20°C, Económica = 16°C.
-
MODE
P3
= Temperature confort de
6h
a
8h30
, de
11h30
a
13h30
y de
16h30
a
23h
.
Temperatura económica de
8h30
a
11h30
, de
13h30
a
16h30
y de
23h
a
6h
.
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
P4
=
Programa libre
que le permite crear tres periodos en temperatura confort y otros tres en temperatura económica para cada día de la semana.
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
Pulse la tecla varias veces para obtener el horario 6:00 : cada pulsación breve hace avanzar
30 minutos, y una pulsación prolongada acelera la progresión.
• Pulse la tecla horario 8:00 .
• Pulse la tecla horario I2:00 .
• Pulse la tecla horario I4:00 .
• Pulse la tecla horario I8:00 .
• Pulse la tecla horario 22:00 .
varias veces para obtener el varias veces para obtener el varias veces para obtener el varias veces para obtener el varias veces para obtener el
Nota :
si ha cometido un error (por ej.: 11h30 en vez de 12h00, utilice las teclas
+
/
-
para avanzar o retroceder, y modifique con las teclas .
Selección de un programa existente P1, P2 o P3 para un día de la semana (en modo programación, todas las modificaciones se validan automáticamente).
Ejemplo:
P2 para miércoles
+
-
MODE
Valide con la tecla
OK
, el día siguiente le es propuesto automáticamente.
Pulse la tecla
MODE
para pasar a modo
Auto
.
Lectura de los programas
Puede verificar su programación:
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
1 2 3 4 5 6 7
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
+
-
Auto Manu
¡c
¡c
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
MODE
Pulse la tecla
PROG P1-P4
para pasar al modo programación.
El N° del programa asignado al día parpadea en la parte derecha del visualizador.
Pulse la tecla
DAYS 1-7
hasta que aparezca el apuntador
▲ bajo el día que desea programar; miércoles en nuestro ejemplo.
Pulse la tecla
PROG P1-P4
hasta que aparezca intermitentemente el número de programa P2 en la parte derecha de la pantalla.
Valide con la tecla
OK
, el día siguiente le es propuesto automáticamente.
Creación de un programa
P4
Un perfil de 24 h compuesto por 48 termómetros en la parte inferior del visualizador le permite visualizar fácilmente la composición de su programa.
Un termómetro vacío hasta la mitad corresponde a 30 minutos en temperatura económica.
DAYS
1-7
PROG
P1-P4
OK
0000
h
Res
Desde el modo
Auto
,pulse la tecla
PROG P1-P4
.
Con la tecla
DAYS 1-7
seleccione el día de 1 a 7, y verifique su programa en el perfil de 24 h en la parte inferior del visualizador (ejemplo siguiente).
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Pulse la tecla
MODE
para pasar a modo
Auto
.
Modo automático (Auto)
El paso a modo automático se efectúa pulsando la tecla
MODE
hasta que aparezca el apuntador
▲ bajo
Auto
.
En modo automático, el
Cronotermostato se adapta a su ritmo de vida, ejecutando el o los programas que haya elegido.
MODE
Auto Manu
° c
Un termómetro lleno corresponde a 30 minutos en temperatura confort.
Ejemplo:
creación de 3 periodos en temperatura confort para el viernes: de
6h
a
8h
, de
12h
a
14h
y de
18h
a
22h
.
+
-
Auto Manu
¡c
¡c
1 2 3 4 5 6 7
☛ ☛
MODE
Modo manual (Manu)
El modo manual transforma su aparato en un simple termostato.
Le permite mantener una temperatura constante en su vivienda (regulable de 5°C a 30°C).
☛ ☛
☛ ☛
2
☛
0
0
1
1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
☛ ☛ ☛
0000
h
Res
☛
☛
☛
+
-
☛
DAYS
1-7
¡c ¡c
PROG
P1-P4
OK
¡c
0000
h
Res
MODE
☛ ☛
Desde el modo
Auto
,pulse la tecla
PROG P1-P4
.
Pulse la tecla
DAYS 1-7
hasta que aparezca el apuntador
▲ debajo del día que desea programar; el viernes en nuestro ejemplo.
Pulse la tecla
PROG P1-P4
hasta que aparezca intermitentemente el número de programa P4 en la parte derecha de la pantalla.Su visualizador indica 0:00 y el primer termómetro parpadea sobre el perfil de 24 h.
Pulse la tecla
MODE
para situar el apuntador
▲ bajo
Manu
.
Pulse
+
o
-
para ajustar la temperatura deseada
(ejemplo 22,5°C).
Para abandonar el modo
Manu
, pulse la tecla
MODE
y vuelva a situar el apuntador
▲ bajo
Auto
.
18
Modificación temporal de la temperatura
En modo automático, esta práctica función le permite modificar temporalmente la temperatura ambiente.
Auto Manu
• Para aumentar la temperatura ambiente, pulse la tecla
+
(varias veces si fuera necesario).
• Para reducir la temperatura, pulse la tecla
-
☛
☛
+
-
0 1
¡c
¡c
2 3 4 5
El indicador del nivel de temperatura actual
(confort o económica) comienza a parpadear.
Esta modificación finalizará en el siguiente cambio de temperatura programada.
Para volver al programa inicial, pulse
MODE
y sitúe el apuntador
▲ bajo
Auto
.
La parada del parpadeo del indicador de temperatura actual (confort o económica) marca el fin de la modificación temporal.
Modo ausencia prolongada vacaciones
Este modo evita el riesgo de helada de su vivienda, manteniendo una temperatura mínima regulable durante sus ausencias.
Puede programar el tiempo que vaya a estar ausente, para prever el aumento de temperatura de su vivienda a su regreso.
2 posibilidades para mantener el sistema antihelada:
Forzamiento de la antihelada permanente
• Pulse la tecla , el día 0I parpadea.
• Pulse una vez la tecla
-
, la indicación F
ORC parpadea.
• Valide con la tecla
OK
.
• Regule el nivel de temperatura que desea durante su ausencia con las tecla
+
/
-
.
• Valide con la tecla
OK
.
Para anular y volver al
Auto
, pulse la tecla
MODE
.
Forzamiento de la antihelada para un número de días.
• Pulse la tecla , el día 0I parpadea.
• Con las teclas
+
/
-
, ajuste la duración de su ausencia en días.
La jornada actual como 1
.
• Valide con la tecla
OK
.
• Regule el nivel de temperatura que desea durante su ausencia con las teclas
+
/
-
.
• Valide con la tecla
OK
.
Para anular y volver al
Auto
, pulse la tecla
MODE
.
Señal de mantenimiento de su
0000
instalación
h
Este modo le permite:
• recordar que debe hacer efectuar un mantenimiento periódico (cambio de filtro en un climatizador, o limpieza de un aparato).
• comparar sus consumos de calefacción o de aire acondicionado de un año a otro (comparando el número de horas de funcionamiento).
Cómputo del número de horas de funcionamiento
Auto Manu
1 2 3 4 5 6 7
+
timer
☛ ☛
MODE
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
DAYS
1-7
PROG
P1-P4
OK
0000
☛
h
Res
Pulse la tecla
0000 h desde el momento en que coloca las pilas,el visualizador le indica el número de horas de funcionamiento de su: quemador, climatizador, etc., según el tipo de aparato pedigree (pulsando
+
o
-
el contador se pone a cero).
Pulse la tecla
MODE
para pasar a modo
Auto
.
Programación de la periodicidad de mantenimiento de su instalación
Pulse la tecla
0000 h
.
Regule con las teclas
+
/
-
lel número de horas de funcionamiento a partir del cual desea ser avisado.
Valide con la tecla
OK
;comienza la cuenta atrás.
Una vez que ésta finalice,será avisado por la aparición de la sigla
timer
.
Regulaciones eventuales
Puede efectuar los diferentes regulaciones en la parte trasera del aparato (cuando está desenchufado).
1- Selección del tipo de regulación
■
Calefacción
■
Aire acondicionado
2- Selección del modo regulación
■
On/Off Cronoproporcional
■
Se recomienda muy especialmente el modo cronoproporcional para instalaciones de calefacción por el suelo (inercia baja o mediana).
3- Función antibloqueo de la bomba de circulación (accionamiento de la bomba durante 1 minuto cada 24 horas)
■
Parrada función antibloqueo
■
Marcha función antibloqueo
Configuración
Para sintonizar un emisor con el receptor:
• Mantener pulsado durante más de 3 segundos el pulsado del receptor.
• El testigo
OK
parpadea, relajar el pulsado.
El receptor está en modo configuración.
• Mantener pulsado durante 3 segundos la tecla
RESET
del Thermoflash DIGI 2 HF.
• El testigo
OK
del receptor deja de parpadear despues de 5 segundos.
La sintonización emisor/receptor queda establecida.
Borrado
Para borrar todas las sincronizaciones emisor/receptor:
• Mantener pulsado durante mas de 10 segundos el pulsador del receptor.
• El testigo
OK
parpadea primero lentamente y luego mas rapidamente.
• Pulsar de nuevo durante 3 segundos el pulsador del receptor.
• El testigo
OK
deja de parpadear, todos las sincronizaciones han sido borrados.
El receptor retorna al modo
Auto
.
Forzamiento
Este producto puede ser controlado manualmente.
• Pulsar rapidamente el pulsador del receptor
(menos de 3 segundos).
Cada presión invierte el estado de la salida.
Nota:
el radiocontrol es siempre prioritario.
¿Qué hacer si ?
•
La calefacción no se pone en marcha:
- el receptor no recibe alimentación: (testigo
OK
apagado). Revisar el fusible y el interruptor.
•
El receptor está fuera del alcance el emisor:
- acercarse más al receptor.
•
El receptor no reconoce el código del emisor:
- volver a instalar el receptor.
•
La aplicación no se pone en marcha o no se deja:
- el receptor está perturbado por una emisión de ondas (radioaficionado, pantalla de televisión, reemisor de teléfono móvil...): intentar desplazar la fuente de emisión de las ondas perturbadoras.
Si el problema continúa, llamar al electricista.
Caracterìsticas técnicas
Emisor
Rango regulación T° confort: +5°C a +30°C
Rango regulación de T° Reducida: +5°C a +30°C
Rango regulación T° Fuera de helada:
+5°C a +30°C
Gama de visualización de la T° ambiente:
Diferencia estática:
0°C a +40°C
<0.3°C
Alimentación: 2 pilas alcalinas 1,5 V LR6
(para alimentar el equipo de productos,
Distancia de emisión: transmisor radio incluido)
75 m en campo libre
3 etapas dentro de una vivienda clásica
Frecuencia de emisión: 433.92 MHz
Relación ciclica de emición:
IP :
10%
30
Escala de funcionamiento: 0°C a +40°C
Temperatura de almacenamiento: -20°C a +70°C
Higrometría:
Grado de polución:
95% a 40°C normal
Volumen:
Normas:
115 x 82 x 34 mm
EN 301-489-3
Receptor
Alimentación:
Carga mìnima:
230 V +10 % a -15 %
12 V 100 mA
Salida: 1 contacto inversor libre de potencial
Poder de corte:
AC1:
Inductivo:
Radiofrecuencia:
Indice de protección:
16 A 250 V
3 A (cos ϕ
= 0,6)
433.92 MHz
IP43
Clase de protección:
Resistencia al choque:
T° de funcionamiento:
T° de almacenamiento:
Capacidad flexible:
Capacidad rigido:
Volumen:
Higrometría:
Receiver class:
Normas:
II
IK04
-10°C a +60°C
-20°C a +70°C
0,5 a 1,5 mm 2
0,5 a 2,5 mm 2
130 x 60 x 27 mm
90% max. a 20°C
2
EN 60669-2-1
Normas:
EN 300220-3,
EN 301-489-1 y EN 301-489-3.
Utilizable en toda Europa
19
Instalación del receptor
!
Antes de calquier manipulación, para la instalación, cortar la corriente!
El esquema de conexión no representa las protecciones. La instalación debe ser realizada por un profesional en el respecto de las normas en vigor.
Para facilitar su instalación el kit Thermoflash
DIGI 2 HF se suministra con un cable flexible de
4 conductores de 1,5 mm
(no conectado).
2 de 1,20 m de largo
Para la conexión del receptor HF, se recomienda el uso de este cable, respetando los colores siguientes:
marrón
= fase
azul
= neutro
gris negro
conexión con la caldera
L
N
5 4 3
L
2
N
1
L
N
5 4 3
L N
2 1
!
En caso de conexión con 2 instalaciones diferentes (calefacción y climatización), piense en apagar uno de los dos aparatos para evitar que los dos funciones simultáneamente en la misma estación.
5 4 3
L
2
N
1
L
N
20
33 rue Saint-Nicolas
B.P. 50152 - 67704 SAVERNE Cedex
Tél. 03 88 01 88 01 - Fax 03 88 01 88 90 www.flash.fr
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Key Features
- Precise temperature regulation and energy saving
- 3 pre-defined heating programs
- Option to create your own heating schedule
- Wireless communication between thermostat and receiver
- Easy to install and program
- Ensures optimal comfort
- Protects against frost