Zebra TC72 User Guide
Reklama
Reklama
TC72
Touch Computer
MN-004055-01EN
ZEBRA and the stylized Zebra head are trademarks of Zebra Technologies Corporation, registered in many jurisdictions worldwide. . All other trademarks are the property of their respective owners.
© 2020 Zebra Technologies Corporation and/or its affiliates. All rights reserved.
For further information regarding legal and proprietary statements, go to:
COPYRIGHTS: www.zebra.com/copyright
WARRANTY: www.zebra.com/warranty
END USER LICENSE AGREEMENT: www.zebra.com/eula
Terms of Use
Proprietary Statement
This manual contains proprietary information of Zebra Technologies Corporation and its subsidiaries
(“Zebra Technologies”). It is intended solely for the information and use of parties operating and maintaining the equipment described herein. Such proprietary information may not be used, reproduced, or disclosed to any other parties for any other purpose without the express, written permission of Zebra
Technologies.
Product Improvements
Continuous improvement of products is a policy of Zebra Technologies. All specifications and designs are subject to change without notice.
Liability Disclaimer
Zebra Technologies takes steps to ensure that its published Engineering specifications and manuals are correct; however, errors do occur. Zebra Technologies reserves the right to correct any such errors and disclaims liability resulting therefrom.
Limitation of Liability
In no event shall Zebra Technologies or anyone else involved in the creation, production, or delivery of the accompanying product (including hardware and software) be liable for any damages whatsoever
(including, without limitation, consequential damages including loss of business profits, business interruption, or loss of business information) arising out of the use of, the results of use of, or inability to use such product, even if Zebra Technologies has been advised of the possibility of such damages. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Revision History
Changes to the original guide are listed below:
Change Date
-01 Rev A 9/2020 Initial release.
Description
2
Table of Contents
3
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner ..................... 38
Pairing the RS507/RS507X/RS6000 Hands-Free Imager ............................................. 39
Pairing in HID Mode Using Near Field Communication.......................................... 40
Pairing Using Bluetooth Human Interface Device .................................................. 41
Pairing Using Bluetooth Human Interface Device .................................................. 42
4
Entering Numbers, Symbols, and Special Characters ..................................... 61
5
Responding with a Private Response .............................................................. 80
6
Configuring Ethernet Static IP Address.......................................................... 109
7
Configuring Ethernet Static IP Address.......................................................... 132
Connecting a Headset to the 3.5 mm Audio Adapter ........................................... 135
Removing the Device from the Trigger Handle .................................................... 146
8
Installing Applications Using the USB Connection ............................................... 165
Installing Applications Using the Android Debug Bridge ...................................... 166
Downloading the System Update Package .......................................................... 168
Performing a System Update Using microSD Card.............................................. 168
Performing an Enterprise Reset From Device Settings........................................ 169
Performing an Enterprise Reset Using microSD Card ......................................... 170
Performing a Factory Reset Using microSD Card................................................ 171
9
Formatting a microSD Card as Internal Memory............................................ 174
10
11
About This Guide
Configurations
This guide covers the following configurations:
Configuratio n
TC720L
Radios
WLAN: 802.11 a/b/g/n/ac/d/h/i/r/k/v
3 w
/
WPAN: Bluetooth v5.0 Low Energy
Display Memory
4.7” High
Definition
(1280 x 720)
LCD
4 GB
RAM/32 GB
Flash
Data
Capture
Options
2D imager, camera and integrated
NFC
Operating
System
Android 10
Notational Conventions
Notational conventions are used to highlight important information.
• Bold
text is used to highlight the following:
•
Dialog box, window and screen names
•
Drop-down list and list box names
•
Check box and radio button names
•
Icons on a screen
•
Key names on a keypad
•
Button names on a screen.
•
Bullets (•) indicate:
•
Action items
•
Lists of alternatives
•
Lists of required steps that are not necessarily sequential.
•
Sequential lists (for example, those that describe step-by-step procedures) appear as numbered lists.
12
About This Guide
Icon Conventions
The following icons are used throughout the document. The icons and their associated meanings are described below.
NOTE:
The text here indicates information that is supplemental for the user to know and that is not required to complete a task.
IMPORTANT:
The text here indicates information that is important for the user to know.
CAUTION:
If the precaution is not heeded, the user could receive minor or moderate injury.
WARNING:
If danger is not avoided, the user CAN be seriously injured or killed.
DANGER:
If danger is not avoided, the user WILL be seriously injured or killed.
Service Information
If you have a problem with your equipment, contact Customer Support for your region. Contact information is available at: zebra.com/support .
When contacting support, please have the following information available:
•
Serial number of the unit (found on manufacturing label)
•
Model number or product name (found on manufacturing label)
•
Software type and version number
Customer Support responds to calls by email or telephone within the time limits set forth in support agreements.
If the problem cannot be solved by Customer Support, the user may need to return the equipment for servicing and will be given specific directions. We are not responsible for any damages incurred during shipment if the approved shipping container is not used. Shipping the units improperly can possibly void the warranty. Remove the microSD card from the device before shipping for service.
If the device was purchased from a business partner, contact that business partner for support.
Determining Software Versions
Before contacting Customer Support, determine the current software version on your device.
1.
2.
Swipe down from the Status bar with two fingers to open the Quick Access panel, and then touch .
Touch
About phone
.
3.
Scroll to view the following information:
• Battery information
• SW components
• Legal information
• Model & hardware
13
About This Guide
• Android version
• Android security patch level
•
Baseband version
• Kernel version
• Build number
Determining the Serial Number
Before contacting Customer Support, determine the serial number of your device.
•
Touch
About phone
>
Model & hardware
>
Serial number.
14
Getting Started
Introduction
This chapter provides information to get the device up and running for the first time.
Unpacking
1.
2.
3.
4.
Carefully remove all protective material from the device and save the shipping container for later storage and shipping.
Verify that the following are included:
•
Touch computer
•
4,620 mAh PowerPercision+ Lithium-ion battery
•
Hand strap
•
Regulatory Guide.
Inspect the equipment for damage. If any equipment is missing or damaged, contact the Global
Customer Support center immediately.
Prior to using the device for the first time, remove the protective shipping film that covers the scan window, display, and camera window.
15
Getting Started
Features
Figure 1
Front View
17
16
15
14
13
18
12
11
1
2
3
10
9
8
4
5
7
6
Table 1
Front View Features
4
5
2
3
Number
1
6
7
8
9
10
11
12
Item
Touch
Screen
Function
Displays all information needed to operate the device.
Scan Button Initiates data capture (programmable).
PTT Button Initiates push-to-talk communications (programmable).
Back Button Displays the previous screen.
Home Button Displays the Home screen with a single press.
On device with GMS, opens the Google Now screen when held for a short period of time.
Microphone
Charging
Contacts
Speaker
Use for communications in Handset mode.
Provides power to the device from cables and cradles.
Provides audio output for video and music playback. Provides audio in speakerphone mode.
Search
Button
Opens the Recent App screen.
Menu Button Opens a menu with items that affect the current screen or app.
Light Sensor Determines ambient light for controlling display backlight intensity.
Proximity
Sensor
Determines proximity for turning off display when in handset mode.
16
Getting Started
Table 1
Front View Features (Continued)
Number
13
14
15
16
17
18
Item
Power Button Turns the display on and off. Press and hold to reset the device, power off or
Microphone
Receiver
Charging/Not ification LED
Data Capture
LED
Front Facing
Camera swap battery.
Function
Use for communications in Speakerphone mode.
Use for audio playback in Handset mode.
Indicates battery charging status while charging and app generated notifications.
Indicates data capture status.
Use to take photos and videos (optional).
Figure 2
Rear View
27
26
24
28
30
29
25
19
24
23
20
21
20
21
22
23
Table 2
Back View Features
Number
19
24
25
26
Item
Interface
Connector via cables and accessories.
Function
Provides USB host and client communications, audio and device charging
Exit Window Provides data capture using the imager.
Microphone Use during video recording and for noise cancellation.
Scan Button Initiates data capture (programmable).
Volume
Up/Down
Button
Increase and decrease audio volume (programmable).
Press to remove the battery.
Battery
Release
Latches
Elastic
Sleeve
Battery
Use to hold optional stylus.
Provides power to the device.
17
Getting Started
Table 2
Back View Features (Continued)
Number
27
28
29
30
Item
Hand strap
Hand strap
Mounting
Point
Camera
Camera
Flash
Use to securely hold the device in your hand.
Provides latching point for the hand strap.
Takes photos and videos.
Function
Provides illumination for the camera.
Setting Up the Device
To start using the device for the first time:
1.
Install a SAM card.
2.
3.
Install a micro secure digital (SD) card (optional).
Install hand strap (optional).
4.
5.
6.
Install the battery.
Charge the device.
Power on the device.
Installing the SAM Card
CAUTION:
Follow proper electrostatic discharge (ESD) precautions to avoid damaging the Secure Access
Module (SAM) card. Proper ESD precautions include, but not limited to, working on an ESD mat and ensuring that the user is properly grounded.
NOTE:
If using a micro SAM card, a third-party adapter is required.
1.
Lift the access door.
18
Getting Started
2.
Insert a SAM card into the SAM slot with the cut edge toward the middle of the device and the contacts facing down.
Mini SAM Slot
3.
4.
Ensure that the SAM card is seated properly.
Replace the access door.
5.
Press the access door down and ensure that it is properly seated.
CAUTION:
Access door must be replaced and securely seated to ensure proper device sealing.
Installing a microSD Card
The microSD card slot provides secondary non-volatile storage. The slot is located under the battery pack.
Refer to the documentation provided with the card for more information, and follow the manufacturer’s recommendations for use.
CAUTION:
Follow proper electrostatic discharge (ESD) precautions to avoid damaging the microSD card.
Proper ESD precautions include, but are not limited to, working on an ESD mat and ensuring that the operator is properly grounded.
1.
2.
Remove the hand strap, if installed.
Lift the access door.
19
Getting Started
3.
Slide the microSD card holder to the Open position.
4.
Lift the microSD card holder.
5.
Insert the microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
20
Getting Started
6.
Close the microSD card holder door and slide the door to the Lock position.
7.
Replace the access door.
8.
Press the access door down and ensure that it is properly seated.
CAUTION:
Access door must be replaced and securely seated to ensure proper device sealing.
Installing the Hand Strap and Battery
NOTE:
User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories.
Performance levels such as sealing (Ingress Protection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
NOTE:
Installation of the hand strap is optional. Skip this section if not installing the hand strap.
1.
Remove the hand strap filler from the hand strap slot. Store the hand strap filler in a safe place for future replacement.
21
Getting Started
2.
Insert the hand strap plate into the hand strap slot.
3.
Insert the battery, bottom first, into the battery compartment in the back of the device.
4.
Press the battery down into the battery compartment until the battery release latches snap into place.
5.
Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
22
Getting Started
Installing the Battery
NOTE:
User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories.
Performance levels such as sealing (Ingress Protection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
1.
Insert the battery, bottom first, into the battery compartment in the back of the device.
2.
Press the battery down into the battery compartment until the battery release latches snap into place.
Charging the Battery
Before using the device for the first time, charge the main battery until the green Charging/Notification light emitting diode (LED) remains lit. To charge the device, use a cable or a cradle with the appropriate power supply. For information about the accessories available for the device, see
for more information.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or accessory always performs battery charging in a safe and intelligent manner. At higher temperatures (approximately +37°C
(+98°F)) the device or accessory may, for small periods of time, alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device or accessory indicates when charging is disabled due to abnormal temperatures via its LED.
To charge the main battery:
1.
Connect the charging accessory to the appropriate power source.
2.
Insert the device into a cradle or attach to a cable. The device turns on and begins charging. The
Charging/Notification LED blinks amber while charging, then turns solid green when fully charged.
23
Getting Started
Charging Indicators
Table 3
Charging/Notification LED Charging Indicators
Off
State Indication
The device is not charging. The device is not inserted correctly in the cradle or connected to a power source. Charger/cradle is not powered.
The device is charging.
Slow Blinking Amber (1 blink every
4 seconds)
Solid Green
Fast Blinking Amber (2 blinks/second)
Charging complete.
Charging error:
•
Temperature is too low or too high.
•
Charging has gone on too long without completion (typically eight hours).
Slow Blinking Red (1 blink every 4 seconds)
Solid Red
The device is charging but the battery is at end of useful life.
Charging complete but the battery is at end of useful life.
Fast Blinking Red (2 blinks/second) Charging error but the battery is at end of useful life.
•
Temperature is too low or too high.
•
Charging has gone on too long without completion (typically eight hours).
Zebra Visibility Services
The device captures and provides device analytics to a system administrator. The first time the device boots (or after a Factory reset), the
Zebra Services
agreement screen displays.
1.
2.
3.
Leave
Device Data
enabled if you want the device to send analytics data.
Touch the
Device Data
switch to disable the device from sending analytics data.
Touch
OK
to confirm selection.
Replacing the Battery
NOTE:
User modification of the device, particularly in the battery well, such as labels, asset tags, engravings, stickers, etc., may compromise the intended performance of the device or accessories.
Performance levels such as sealing (Ingress Protection (IP)), impact performance (drop and tumble), functionality, temperature resistance, etc. could be effected. DO NOT put any labels, asset tags, engravings, stickers, etc. in the battery well.
CAUTION:
Do not add or remove SIM, SAM or microSD card during battery replacement.
1.
2.
3.
Remove any accessory attached to the device.
Press the Power button until the menu appears.
Touch
Battery Swap
.
24
Getting Started
4.
5.
6.
Follow the on-screen instructions.
Wait for the LED to turn off.
If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
7.
Press the two battery latches in.
25
8.
Lift the battery from the device.
Getting Started
CAUTION:
Replace the battery within two minutes. After two minutes the device reboots and data may be lost.
9.
Insert the replacement battery, bottom first, into the battery compartment in the back of the device.
10.
Press the battery down until the battery release latch snaps into place.
11.
Replace the hand strap, if required.
12.
Press and hold the Power button to turn on the device.
NOTE:
After replacing the battery, wait 15 minutes before using
Battery Swap
again.
Replacing the SIM or SAM Card
NOTE:
SIM replacement applies to TC77 only.
To replace the SIM or SAM card:
1.
Press and hold the Power button until the menu appears.
2.
3.
Touch
Power off
.
Touch
OK
.
26
Getting Started
4.
If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
5.
6.
7.
Press the two battery latches in.
Lift the battery from the device.
Lift the access door.
8.
Remove card from holder.
Figure 3
Remove SAM Card
Figure 4
Remove Nano SIM Card
9.
Insert the replacement card.
27
Figure 5
Insert SAM Card
Getting Started
Figure 6
Insert Nano SIM Card
Mini SAM Slot
10.
Replace the access door.
11.
Press the access door down and ensure that it is properly seated.
CAUTION:
Access door must be replaced and securely seated to ensure proper device sealing.
12.
Insert the battery, bottom first, into the battery compartment in the back of the device.
13.
Press the battery down until the battery release latch snaps into place.
14.
Replace the hand strap, if required.
15.
Press and hold the Power button to turn on the device.
Replacing the microSD Card
To replace the microSD card:
1.
Press the Power button until the menu appears.
2.
3.
Touch
Power off
.
Touch
OK
.
28
Getting Started
4.
If hand strap is attached, slide the hand strap clip up toward the top of the device and then lift.
5.
6.
Press the two battery latches in.
Lift the battery from the device.
7.
Lift the access door.
8.
9.
Slide the microSD card holder to the Open position.
Lift the microSD card holder.
10.
Remove microSD card from holder.
11.
Insert the replacement microSD card into the card holder door ensuring that the card slides into the holding tabs on each side of the door.
12.
Close the microSD card holder door and slide the door to the Lock position.
29
13.
Replace the access door.
Getting Started
14.
Press the access door down and ensure that it is properly seated.
CAUTION:
Access door must be replaced and securely seated to ensure proper device sealing.
15.
Insert the battery, bottom first, into the battery compartment in the back of the device.
16.
Press the battery down until the battery release latch snaps into place.
17.
Replace the hand strap, if required.
18.
Press and hold the Power button to turn on the device.
30
Data Capture
Introduction
The device supports data capture using:
•
Integrated Imager
•
Integrated Camera
•
RS507/RS507X Hands-free Imager
•
RS6000 Bluetooth Ring Scanner
•
DS3578 Digital Scanner
•
DS3608 Digital Scanner
•
DS3678 Digital Scanner.
Integrated Imager
The device with an integrated 2D imager has the following features:
•
Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal,
PDF417, Digimarc, and 2D matrix code types.
•
The ability to capture and download images to a host for a variety of imaging applications.
•
Advanced intuitive laser aiming cross-hair and dot aiming for easy point-and-shoot operation.
The imager uses imaging technology to take a picture of a barcode, stores the resulting image in memory, and executes state-of-the-art software decoding algorithms to extract the barcode data from the image.
Operational Modes
The device with an integrated imager supports two modes of operation, listed below. Activate each mode by pressing the Scan button.
•
Decode mode - The device attempts to locate and decode enabled barcodes within its field of view. The imager remains in this mode as long as you hold the scan button, or until it decodes a barcode.
NOTE:
To enable Pick List Mode, configure in DataWedge or set in an application using a API command.
31
Data Capture
•
Pick List mode - Selectively decode a barcode when more than one barcode is in the device’s field of view by moving the aiming crosshair or dot over the required barcode. Use this feature for pick lists containing multiple barcodes and manufacturing or transport labels containing more than one barcode type (either 1D or 2D).
Digital Camera
The device with an integrated camera based barcode scanning solution has the following features:
•
Omnidirectional reading of a variety of barcode symbologies, including the most popular linear, postal,
QR, PDF417, and 2D matrix code types.
•
Cross-hair reticle for easy point-and-shoot operation.
•
Picklist mode to decode a particular barcode from many in the field of view.
The solution uses the advanced camera technology to take a digital picture of a barcode, and executes state-of-the-art software decoding algorithms to extract the data from the image.
RS507/RS507X Hands-Free Imager
The RS507/RS507X Hands-free Imager is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 9
RS507/RS507X Hands-Free Imager
Refer to the RS507/RS507X Hands-free Imager Product Reference Guide for more information.
RS6000 Bluetooth Ring Scanner
The RS6000 Bluetooth Ring Scanner is a wearable barcode scan solution for both 1D and 2D barcode symbologies.
Figure 10
RS6000 Bluetooth Ring Scanner
Refer to the RS6000 Bluetooth Ring Scanner Product Reference Guide for more information.
32
Data Capture
DS3678 Digital Scanner
The cordless DS3678 combines superior 1D and 2D omnidirectional barcode scanning performance and advanced ergonomics in a lightweight design. See the DS36X8 Product Reference Guide for more information.
Figure 11
DS3678 Digital Scanner
Scanning Considerations
Typically, scanning is a simple matter of aim, scan, and decode, with a few quick trial efforts to master it.
However, consider the following to optimize scanning performance:
• Range:
Scanners decode best over a particular working range — minimum and maximum distances from the barcode. This range varies according to barcode density and scanning device optics. Scan within range for quick and constant decodes; scanning too close or too far away prevents decodes.
Move the scanner closer and further away to find the right working range for the barcodes being scanned.
• Angle:
Scanning angle is important for quick decodes. When the illumination/flash reflects directly back into the imager, the specular reflection can blind/saturate the imager. To avoid this, scan the barcode so that the beam does not bounce directly back. Do not scan at too sharp an angle; the scanner needs to collect scattered reflections from the scan to make a successful decode. Practice quickly shows what tolerances to work within.
•
Hold the device farther away for larger symbols.
•
Move the device closer for symbols with bars that are close together.
NOTE:
Scanning procedures depend on the app and device configuration. An app may use different scanning procedures from the one listed above.
Scanning with Internal Imager
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows the user to enable the imager, decode the barcode data, and display the barcode content.
33
Data Capture
To scan with the internal imager:
1.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
2.
Point the exit window on the top of the device at a barcode.
3.
Press and hold the scan button.
The red laser aiming pattern turns on to assist in aiming.
NOTE:
When the device is in Picklist mode, the imager does not decode the barcode until the crosshair or aiming dot touches the barcode.
4.
Ensure the barcode is within the area formed by the crosshairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 12
Aiming Pattern
Figure 13
Pick List Mode with Multiple Barcodes
5.
The Data Capture LED lights green and a beep sounds, by default, to indicate the barcode was decoded successfully.
34
Data Capture
6.
Release the scan button.
The barcode content data displays in the text field.
NOTE:
Imager decoding usually occurs instantaneously. The device repeats the steps required to take a digital picture (image) of a poor or difficult barcode as long as the scan button remains pressed.
Scanning with Integrated Camera
To capture bar code data:
NOTE:
When capturing bar code data in poor lighting, turn on Illumination mode in the DataWedge app.
See the device Integrator Guide for detailed information on configuring DataWedge.
1.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
For example, open the web browser and touch the text field.
2.
3.
Aim the camera at a bar code.
Press and hold the Scan button. By default, a preview window appears on the screen. The Decode light emitting diode (LED) lights red to indicate that data capture is in process.
NOTE:
When Picklist mode is enabled, move the device until the bar code is centered under the red target on the screen.
4.
Move the device until the bar code is visible on the screen.
5.
6.
The Decode LED lights green, a beep sounds and the device vibrates, by default, to indicate the bar code was decoded successfully.
The captured data appears in the text field.
Scanning with RS507/RS507X Hands-Free Imager
To read a barcode, a scan-enabled app is required. The device contains the DataWedge app that allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS507/RS507X:
1.
Pair the RS507/RS507X with the device. See Pairing Using Simple Serial InterfacePairing Bluetooth
Scanners or Pairing Using Bluetooth Human Interface Device for more information.
35
Data Capture
2.
3.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the RS507/RS507X at a barcode.
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS507/RS507X LEDs light green and a beep sounds to indicate the barcode was decoded successfully. When the RS507/RS507X is in Pick List mode, the RS507/RS507X does not decode the barcode until the center of the crosshair touches the barcode.
Figure 14
RS507/RS507X Aiming Pattern
Figure 15
RS507/RS507X Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
36
Data Capture
Scanning with RS6000 Bluetooth Ring Scanner
To read a barcode, a scan-enabled app is required. Devices that contain the Zebra DataWedge app allows you to enable the scanner to decode barcode data and display the barcode content.
To scan with the RS6000:
1.
2.
3.
Pair the RS6000 with the device. See Pairing Using Bluetooth Human Interface Device for more information.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the RS6000 at a barcode.
4.
Press and hold the trigger.
The red laser aiming pattern turns on to assist in aiming. Ensure the barcode is within the area formed by the cross-hairs in the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
The RS6000 LEDs light green and a beep sounds to indicate the barcode was decoded successfully.
When the RS6000 is in Pick List mode, the RS6000 does not decode the barcode until the center of the crosshair touches the barcode.
Figure 16
RS6000 Aiming Pattern
37
Data Capture
Figure 17
RS6000 Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
Scanning with the DS3608 USB Scanner or DS3678 Bluetooth Scanner
To scan with the DS3608 or DS3678:
1.
Pair the scanner with the device. For more information, see Connecting a USB Scanner for the DS3608 or Pairing Bluetooth Scanners for the DS3678.
2.
3.
Ensure that an app is open on the device and a text field is in focus (text cursor in text field).
Point the scanner at a barcode.
4.
Press and hold the trigger.
Ensure the barcode is within the area formed by the aiming pattern. The aiming dot increases visibility in bright lighting conditions.
Figure 18
DS3608/DS3678 Aiming Pattern
38
Data Capture
Figure 19
DS3608/DS3678 Pick List Mode with Multiple Barcodes in Aiming Pattern
5.
The captured data appears in the text field.
Pairing the RS507/RS507X/RS6000 Hands-Free Imager
To connect the RS507/RS507X or RS6000 imager to the device, use one of the following methods:
•
Near Field Communication (NFC) (RS6000 only)
•
Simple Serial Interface (SSI)
•
Bluetooth Human Interface Device (HID) Mode.
Pairing Using Near Field Communication
The device provides the ability to pair the RS6000 using NFC.
NOTE:
RS6000 Only.
To pair using NFC:
1.
Ensure that the RS6000 is in SSI mode. Refer to the RS6000 User Guide for more information.
2.
3.
Ensure that NFC is enabled on the device.
Align the NFC icon on the RS6000 with the NFC antenna on the device.
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the device. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
NFC Logo
39
NFC Antenna Area
Data Capture
Pairing in HID Mode Using Near Field Communication
The device provides the ability to pair the RS6000 in HID mode using NFC.
NOTE:
RS6000 Only.
To pair in HID mode using NFC:
1.
Ensure that NFC is enabled on the device.
2.
3.
Ensure that Bluetooth is enabled on the device.
Place the RS6000 in Human Interface Device (HID) mode. If the RS6000 is already in HID mode, skip to step 4.
a.
b.
Remove the battery from the RS6000.
Press and hold the Restore key.
c.
d.
e.
Install the battery onto the RS6000.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
Scan the barcode below to place the RS6000 in HID mode.
4.
5.
6.
Remove the battery from the RS6000.
Re-install the battery into the RS6000.
Align the NFC icon on the RS6000 with the NFC antenna on the device.
The RS6000 Status LED blinks blue indicating that the RS6000 is attempting to establish connection with the device. When connection is established, the Status LED turns off and the RS6000 emits a single string of low/high beeps.
A notification appears on Notification panel and the icon appears in the Status bar.
NFC Logo
NFC Antenna Area
Pairing Using Simple Serial Interface (SSI)
To pair the RS507/RS507X or RS6000 with the device using SSI.
40
Data Capture
1.
Swipe up from the bottom of the Home screen and touch .
2.
Using the RS507/RS507X or RS6000, scan the barcode on the screen.
The RS507/RS507X or RS6000 emits a string of high/low/high/low beeps. The Scan LED flashes green indicating that the RS507/RS507X or RS6000 is attempting to establish connection with the device.
When connection is established, the Scan LED turns off and the RS507/RS507X or RS6000 emits one string of low/high beeps.
A notification appears on the Notification panel and the icon appears in the Status bar.
Pairing Using Bluetooth Human Interface Device
To pair the RS507/RS507X or RS6000 with the device using Human Interface Device (HID):
1.
Ensure that Bluetooth is enabled on both devices.
2.
3.
4.
Ensure that the Bluetooth device to discover is in discoverable mode.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Place the RS507/RS507X or RS6000 in HID mode. If the RS507/RS507X or RS6000 is already in HID mode, skip to step 5.
a.
b.
c.
d.
e.
Remove the battery from the RS507/RS507X or RS6000.
Press and hold the Restore key.
Install the battery onto the RS507/RS507X or RS6000.
Keep holding the Restore key for about five seconds until a chirp is heard and the Scan LEDs flash green.
Scan the barcode below to place the RS507/RS507X or RS6000 in HID mode.
41
Data Capture
Figure 20
RS507 Bluetooth HID Barcode
Figure 21
RS6000 Bluetooth HID Barcode
5.
6.
7.
8.
Remove the battery from the RS507/RS507X or RS6000.
Re-install the battery into the RS507/RS507X or RS6000.
Go to
Settings
.
Touch
Bluetooth
.
9.
Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
10.
Scroll through the list and select RS507/RS507X or RS6000.
The device connects to the RS507/RS507X or RS6000 and
Connected
appears below the device name. The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
A notification appears on Notification panel and the icon appears in the Status bar.
Pairing a Bluetooth Scanner
Connect the scanner to the device using one of the following methods:
•
Simple Serial Interface (SSI) mode
•
Bluetooth Human Interface Device (HID) mode.
Pairing Using Bluetooth Human Interface Device
To pair the scanner with the device using HID:
1.
Remove the battery from the scanner.
2.
3.
Replace the battery.
After the scanner reboots, scan the barcode below to place the scanner in HID mode.
4.
5.
6.
On the device, swipe down from the Status bar to open the Quick Access panel and then touch .
Touch
Bluetooth
.
Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
42
Data Capture
7.
Scroll through the list and select XXXXX xxxxxx, where XXXXX is the scanner and xxxxxx is the serial number.
The device connects to the scanner, the scanner beeps once and
Connected
appears below the device name. The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
DataWedge
DataWedge is a utility that adds advanced barcode scanning capability to any application without writing code. It runs in the background and handles the interface to built-in barcode scanners. The captured barcode data is converted to keystrokes and sent to the target application as if it was typed on the keypad.
DataWedge allows any app on the device to get data from input sources such as a barcode scanner, MSR,
RFID, voice, or serial port and manipulate the data based on options or rules.
Configure DataWedge to:
•
Provide data capture services from any app.
•
Use a particular scanner, reader or other peripheral device.
•
Properly format and transmit data to a specific app.
To configure DataWedge refer to techdocs.zebra.com/datawedge/ .
Enabling DataWedge
1.
2.
3.
4.
Swipe up from the bottom of the Home screen and touch .
Touch >
Settings
.
Touch the
DataWedge enabled
checkbox. A blue checkmark appears in the checkbox indicating that
DataWedge is enabled.
Touch the Home button.
Disabling DataWedge
1.
2.
Touch .
Touch
Settings
.
3.
Touch
DataWedge enabled
.
The blue check disappears from the checkbox indicating that DataWedge is disabled.
Supported Decoders
NOTE:
DataWedge supports the decoders listed below but not all are validated on this device.
43
Table 4
Supported Decoders
Data Capture
Decoders
Australian Postal O
Aztec
Canadian Postal
Chinese 2 of 5
Codabar
Code 11
Code 128
Code 39
Code 93
Composite AB
Composite C
Discrete 2 of 5
Datamatrix
Dutch Postal
DotCode
EAN13
EAN8
Grid Matrix
GS1 DataBar
GS1 DataBar
Expanded
GS1 DataBar Limited O
GS1 Datamatrix O
GS1 QRCode
HAN XIN
Interleaved 2 of 5 O
O
O
X
X
X
O
X
X
X
O
O
O
O
O
X
X
X
O
X
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
O
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
--
O
O
O
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
--
O
O
--
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
--
O
O
--
O
O
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
--
O
--
--
O
--
O
O
O
X
X
O
O
O
O
O
X
X
X
O
X
X
X
O
X
--
O
O
--
O
O
O
--
O
X
--
--
--
O
O
--
X
X
X
O
X
X
X
O
--
--
O
--
O
O
--
O
44
Data Capture
Table 4
Supported Decoders (Continued)
Decoders
Japanese Postal
Korean 3 of 5
MAIL MARK
Matrix 2 of 5
Maxicode
MicroPDF
MicroQR
MSI
PDF417
QR Code
Decoder Signature
TLC 39
Trioptic 39
UK Postal
UPCA
UPCE0
UPCE1
US4state
US4state FICS
US Planet
US Postnet
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
Key
X = Enabled
O = Disabled
-- = Not Supported
Touch the Back button to return to the previous screen.
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
--
O
O
O
X
X
O
O
--
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
O
O
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
--
--
O
--
--
--
--
O
--
--
--
O
--
--
--
O
--
O
X
X
O
O
--
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
X
X
O
O
--
O
X
X
O
O
O
O
O
O
O
X
O
X
O
O
O
45
Using the Device
Home Screen
Turn on the device to display the Home screen. Depending on how your system administrator configured your device, your Home screen may appear differently than the graphics in this section.
After a suspend or screen time-out, the Home screen displays with the lock slider. Touch the screen and slide up to unlock.
The Home screen provides four additional screens to place widgets and shortcuts. Swipe the screen left or right to view the additional screens.
NOTE:
By default, AOSP devices do not have the same icons on the Home screen as GMS devices. Icons are shown below for example only.
Home screen icons can be configured by the user and may look different than shown.
Figure 22
Home Screen
46
Using the Device
1
2
3
4
Status Bar
Widgets
Shortcut Icons
Folder
Displays the time, status icons (right side), and notification icons (left side).
For more information see Notification Icons on page 47
and
.
Launches stand-alone apps that run on the Home screen.
Opens apps installed on the device.
Contains apps.
Setting Home Screen Rotation
By default, the Home screen rotation is disabled.
1.
Touch and hold anywhere on the Home screen until the options appear.
2.
3.
Touch
Home settings
.
Touch the
Allow Home screen rotation
switch.
4.
5.
Touch the Home button.
Rotate the device.
Status Bar
The Status bar displays the time, notification icons (left side), and status icons (right side).
If there are more notifications than can fit in the Status bar, a dot displays indicating that more notifications exist. Swipe down from the Status bar to open the Notification panel and view all notifications and status.
Figure 23
Notification and Status Icons
1
2
1
Notification Icons. See Notification Icons on page 47 .
Status Icons. See
.
Notification Icons
Notification icons indicate app events and messages.
Table 5
Notification Icons
Icon
Main battery is low.
Description
More notifications are available for viewing.
Data is syncing.
Indicates an upcoming event. AOSP devices only.
2
47
Using the Device
Table 5
Notification Icons (Continued)
Icon Description
Indicates an upcoming event. GMS devices only.
Open Wi-Fi network is available.
Audio is playing.
Problem with sign-in or sync has occurred.
Device is uploading data.
Animated: the device is downloading data. Static: the download is complete.
Device is connected to or disconnected from a virtual private network (VPN).
Preparing internal storage by checking it for errors.
USB debugging is enabled on the device.
BT Headset is connected to the device.
PTT Express Voice client status. See the PTT Express PTT Notification Icons for a complete list.
Indicates the RxLogger app is running.
Indicates the Bluetooth scanner is connected to the device.
Indicates the ring scanner is connected to the device in HID mode.
Status Icons
Status icons display system information for the device.
Table 6
Status Icons
Icon
Alarm is active.
Main battery is fully charged.
Main battery is partially drained.
Description
Main battery charge is low.
Main battery charge is very low.
Main battery is charging.
All sounds, except media and alarms, are muted. Vibrate mode is active.
48
Using the Device
Table 6
Status Icons (Continued)
Icon Description
Indicates that all sounds except media and alarms are muted.
Do Not Disturb mode active.
Airplane Mode is active. All radios are turned off.
Bluetooth is on.
The device is connected to a Bluetooth device.
Connected to a Wi-Fi network. Indicates the Wi-Fi version number.
Not connected to a Wi-Fi network or no Wi-Fi signal.
Connected to an Ethernet network.
Speakerphone enabled.
Managing Notifications
Notification icons report the arrival of new messages, calendar events, alarms, and ongoing events. When
for a list of possible notification icons and their description.
•
To view a list of all notifications, open the Notification panel by dragging the Status bar down from the top of the screen.
Quick Settings Bar
•
To respond to a notification, open the Notification panel and then touch a notification. The Notification panel closes and the corresponding app opens.
49
Using the Device
•
To manage recent or frequently used notifications, open the Notification panel and then touch
Manage notifications
. Touch the toggle switch next to an app to turn off all notifications, or touch an app for more notification options.
•
To clear all notifications, open the Notification panel and then touch
CLEAR ALL
. All event-based notifications are removed. Ongoing notifications remain in the list.
•
To close the Notification panel, swipe the Notification panel up.
Opening the Quick Access Panel
Use the Quick Access panel to access frequently used settings (for example, Airplane mode). To get to the
Quick Access Panel:
•
If the device is locked, swipe down once.
•
If the device is unlocked, swipe down once with two fingers, or twice with one finger.
•
If the Notification panel is open, swipe down from the Quick Settings bar.
NOTE:
Not all icons are pictured. Icons may vary.
Quick Access Panel Icons
•
Display brightness - Use the slider to decrease or increase the brightness of the screen.
•
Wi-Fi network - Turn Wi-Fi on or off. To open Wi-Fi settings, touch the Wi-Fi network name.
•
Bluetooth settings - Turn Bluetooth on or off. To open Bluetooth settings, touch
Bluetooth
.
•
Battery saver - Turn Battery saver mode on or off. When Battery saver mode is on the performance of the device is reduced to preserve battery power.
•
Invert colors - Invert the display colors.
•
Do not disturb - Control how and when to receive notifications.
50
Using the Device
•
Airplane mode - Turn Airplane mode on or off. When Airplane mode is on the device does not connect to Wi-Fi or Bluetooth.
•
Auto-rotate - Lock the device’s orientation in portrait or landscape mode or set to automatically rotate.
•
Flashlight - Turn flashlight on or off. Turn camera flash on or off.
The thermal protection safety feature for the camera provides the following behavior if the temperature range is 40°C or above:
•
If the flashlight is kept on for a certain period of time, it is automatically turned off and cannot be turned back on for a period of time until it has cooled off.
•
During the cooling off period, the camera cannot be turned on. If you attempt to use the camera, a message displays indicating to try again after a period of time.
•
Location - Enable or disable locationing feature.
•
Hotspot - Turn on to share the device’s mobile data connection with other devices.
•
Data Saver - Turn on to prevent some apps from sending or receiving data in the background.
•
Night Light - Tint the screen amber to make it easier to look at the screen in dim light. Set Night Light to turn on automatically from sunset to sunrise, or at other times.
•
Screen Cast - Share phone content on Chromecast or a television with Google Cast built-in. Touch cast screen to display a list of devices, then touch a device to begin casting.
•
Dark Theme - Toggles dark theme on and off. Dark themes reduce the luminance emitted by the screen, while meeting minimum color contrast ratios. It helps improve visual ergonomics by reducing eye strain, adjusting brightness to current lighting conditions, and facilitating screen use in dark environments, while conserving battery power.
•
Focus mode - Turn on to pause distracting apps. To open Focus mode settings, touch and hold.
•
Bedtime mode - Turn grayscale on and off. Grayscale turns the screen black and white, reducing phone distractions and improving battery life.
Editing Icons on the Quick Settings Bar
The first several setting tiles from the Quick Access panel become the Quick Settings bar.
•
Open the Quick Access panel and touch to edit, add, or remove settings tiles.
Battery Management
Observe the recommended battery optimization tips for your device.
•
Set the screen to turn off after a short period of non-use.
•
Reduce screen brightness.
•
Turn off all wireless radios when not in use.
•
Turn off automatic syncing for Email, Calendar, Contacts, and other apps.
•
Minimize use of apps that keep the device from suspending, for example, music and video apps.
NOTE:
Before checking the battery charge level, remove the device from any AC power source (cradle or cable).
51
Using the Device
Checking Battery Status
•
Open
Settings
and touch
About phone
>
Battery Information
.
Or, swipe up from the bottom of the screen and touch to open the
Battery Manager
app. See
• Battery present status
indicates if the battery is present.
• Battery level
lists the battery charge (as a percentage of fully charged).
•
Swipe down with two fingers from the status bar to open the quick access panel.
•
Battery percentage is displayed next to the battery icon.
Monitoring Battery Usage
The
Battery
screen provides battery charge details and power management options to extend battery life.
1.
Go to
Settings
.
2.
Touch
Battery
.
Display battery information and power management options for a specific app.
1.
2.
Go to
Settings
.
Touch
Apps & notifications
.
3.
4.
Touch an app.
Touch
Advanced
>
Battery
.
Different apps display different information. Some apps include buttons that open screens with settings to adjust power use. Use the
DISABLE
or
FORCE STOP
buttons to turn off apps that consume too much power.
Low Battery Notification
When the battery charge level drops below 18%, the device displays a notice to connect the device to power. The user should charge the battery using one of the charging accessories.
When the battery charge drops below 10%, the device displays a notice to connect the device to power.
The user must charge the battery using one of the charging accessories.
When the battery charge drops below 4%, the device turns off. The user must charge the battery using one of the charging accessories.
Interactive Sensor Technology
The device contains sensors that monitor movement, orientation and ambient light.
•
Gyroscope - Measures angular rotational velocity to detect rotation of the device.
•
Accelerometer - Measures the linear acceleration of movement to detect the orientation of the device.
•
Digital Compass - The digital compass or magnetometer provides simple orientation in relation to the
Earth's magnetic field. As a result, the device always knows which way is North so it can auto rotate digital maps depending on the physical orientation of the device.
•
Light Sensor - Detects ambient light and adjusts the screen brightness.
52
Using the Device
•
Proximity Sensor - Detects the presence of nearby objects without physical contact. The sensor detects when the device close to your face during a call and turns off the screen, preventing unintentional screen touches.
In order to take advantage of these sensors, applications use API commands. Refer to the Google Android
Sensor APIs for more information. For information on the Zebra Android EMDK, go to: techdocs.zebra.com
.
Waking the Device
The device goes into Suspend mode when you press the Power button or after a period of inactivity (set in the Display settings window).
1.
To wake the device from Suspend mode, press the Power button.
The Lock screen displays.
2.
Swipe the screen up to unlock.
•
If the Pattern screen unlock feature is enabled, the Pattern screen appears instead of the Lock screen.
•
If the PIN or Password screen unlock feature is enabled, enter the PIN or password after unlocking the screen.
NOTE:
If you enter the PIN, password, or pattern incorrectly five times, you must wait 30 seconds before trying again.
If you forget the PIN, password, or pattern contact your system administrator.
USB Communication
Connect the device to a host computer to transfer files between the device and the host computer.
When connecting the device to a host computer, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files. For information on USB communication accessories available for this device, see Accessories.
Transferring Files
Use Transfer files to copy files between the device and the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
On the device, pull down the Notification panel and touch
Charging this device via USB
.
By default,
No data transfer
is selected.
Touch
File Transfer
.
NOTE:
After changing the setting to
File Transfer
, and then disconnect the USB cable, the setting reverts back to
No data transfer
. If the USB cable is reconnected, select
File Transfer
again.
4.
5.
On the host computer, open a file explorer application.
Locate the
device
as a portable device.
6.
7.
Open the SD card or the Internal storage folder.
Copy files to and from the device or delete files as required.
53
Using the Device
Transferring Photos
Use
PTP
to copy photos from the device to the host computer.
1.
Connect the device to a host computer using a USB accessory.
2.
3.
On the device, pull down the Notification panel and touch
Charging this device via USB
.
Touch
PTP
.
4.
5.
6.
On the host computer, open a file explorer application.
Open the SD card or the Internal storage folder.
Copy or delete photos as required.
Disconnect from the Host Computer
CAUTION:
Carefully follow the host computer’s instructions to unmount the microSD card and disconnect
USB devices correctly to avoid losing information.
To disconnect the device from the host computer:
1.
On the host computer, unmount the device.
2.
Remove the device from the USB accessory.
54
Settings
Accessing Settings
There are multiple ways to access settings on a device.
•
Swipe down with two fingers from the top of the Home screen to open the Quick Access panel and touch
.
•
Double-swipe down from the top of the Home screen to open the Quick Access panel and touch
.
•
Swipe up from the bottom of the Home screen to open APPS and touch
Settings
.
Display Settings
Use Display settings to change the screen brightness, enable night light, change the background image, enable screen rotation, set sleep time, and change font size.
Setting the Screen Brightness Manually
Manually set the screen brightness using the touchscreen.
1.
Swipe down with two fingers from the Status bar to open the Quick Access panel.
2.
Slide the icon to adjust the screen brightness level.
Setting the Screen Brightness Automatically
Automatically adjust the screen brightness using the built-in light sensor.
1.
Go to
Settings
.
2.
3.
Touch
Display
.
If disabled, touch
Adaptive brightness
to automatically adjust the brightness.
4.
By default,
Adaptive brightness
is enabled. Toggle the switch to disable.
Touch the Home button.
Setting Night Light
The Night Light setting tints the screen amber, making the screen easier to look at in low light.
1.
Go to
Settings
.
2.
Touch
Display
.
55
Settings
6.
7.
8.
3.
4.
5.
Touch
Night Light
.
Touch
Schedule
.
Select one of the schedule values:
•
None (default)
•
Turns on at custom time
•
Turns on from sunset to sunrise.
By default,
Night Light
is disabled. Touch
TURN ON NOW
to enable.
Adjust the tint using the
Intensity
slider.
Touch the Home button.
Setting Screen Rotation
By default, screen rotation is enabled.
1.
Go to
Settings
.
2.
3.
Touch
Display
>
Advanced
.
Touch
Auto-rotate screen
.
NOTE:
To change the Home screen rotation, see
Setting Home Screen Rotation on page 47
.
4.
Touch the Home button.
Setting Screen Timeout
Set the screen sleep time.
1.
Go to
Settings
.
2.
3.
Touch
Display
>
Advanced
>
Screen timeout
.
Select one of the sleep values.
• 15 seconds
• 30 seconds
• 1 minute
(default)
• 2 minutes
4.
• 5 minutes
• 10 minutes
• 30 minutes
Touch the Home button.
Lock Screen Display
The lock screen display setting wakes the screen when notifications are received.
1.
Go to
Settings
.
2.
Touch
Display
>
Advanced
.
56
Settings
3.
4.
5.
Touch
Lock screen display
.
In the
When to show
section, enable or disable an option using the switch.
Touch the Home button.
Setting Touch Key Light
The four touch keys under the screen are backlit. Configure the touch key light to save battery power.
1.
Go to
Settings
.
2.
3.
Touch
Display
>
Advanced
.
Touch
Touch key light
.
4.
Select an option to choose how long the touch key light stays on:
• Always off
• 6 seconds (default)
• 10 seconds
5.
• 15 seconds
• 30 seconds
• 1 minute
• Always on.
Touch the Home button.
Setting Font Size
Set the size of the font in system apps.
1.
Go to
Settings
.
2.
3.
Touch
Display
>
Advanced
.
Touch
Font size
.
4.
5.
Select one of the font size values.
•
Small
•
Default
•
Large
•
Largest.
Touch the Home button.
Notification LED Brightness Level
Set the brightness of the Notification LED.
1.
Go to
Settings
.
2.
3.
4.
Touch
Display
>
Advanced
.
Touch
Notification LED Brightness Level
.
Use the slider to set the brightness value (default: 15).
57
Settings
5.
Touch the Home button.
Touch Panel Mode
The device display is able to detect touches using a finger, a conductive-tip stylus, or gloved finger.
NOTE:
A glove can be made of medical latex, leather, cotton, or wool.
For optimal performance use a Zebra certified stylus.
1.
2.
Go to
Settings
.
Touch
Display
>
Advanced
.
3.
4.
5.
Touch
Touch panel mode
.
Select:
a.
b.
c.
Glove and Finger (Screen Protector off)
to use a finger or a gloved finger on the screen without a screen protector.
Stylus and Finger (Screen Protector off)
to use a finger or a stylus on the screen without a screen protector.
Finger Only (Screen Protector off)
to use a finger on the screen without a screen protector.
d.
e.
Glove and Finger (Screen Protector on)
to use a finger or a gloved finger on the screen with a screen protector.
Stylus and Finger (Screen Protector on)
to use a finger or a stylus on the screen with a screen protector.
Touch the Home button.
Setting the Date and Time
You are only required to set the time zone or set the date and time if the wireless LAN does not support
Network Time Protocol (NTP).
1.
2.
Go to
Settings
.
Touch
System
>
Date & time
.
3.
4.
5.
6.
Touch
Date
.
In the calendar, set today’s date.
Touch
OK
.
Touch
Time
.
7.
8.
Touch the green circle, drag to the current hour and then release.
Touch the green circle, drag to the current minute and then release.
9.
Touch
AM
or
PM
.
10.
Touch
OK
.
11.
Touch
Use 24-hour format
.
12.
Touch the Home button.
58
Settings
General Sound Setting
Use the
Sound
settings to configure media and alarm volumes.
1.
Go to
Settings
.
2.
3.
Touch
Sound
.
Touch an option to set sounds.
Sound Options
• Zebra volume controls
• Ring volume
- Controls the ringtone volume.
• Media volume
- Controls the music, games, and media volume.
• Alarm volume
- Controls the alarm clock volume.
• Notifications volume
- Controls the notification volume.
• In call volume
- Controls the volume during a call.
• Scanner volume
- Controls the scanner volume.
• Volume presets
•
- Mutes the ring, notifications, and scanner so that the device does not make sounds or vibrate.
•
- All sounds except media and alarms are silenced and vibrate mode is active.
•
- Enables all sounds at the user defined levels.
• Vibrate for calls
- Switch on or off.
• Do Not Disturb
- Mutes some or all sounds and vibrations.
• Shortcut to prevent ringing
- Select how the shortcut method prevents ringing.
• Phone ringtone -
Select a sound to play when the phone rings.
• Default notification sound
- Select a sound to play for all system notifications.
• Default alarm sound
- Select a sound to play for alarms.
• Other sounds and vibrations
• Dial pad tones
- Play a sound when pressing keys on dial pad (default - disabled).
• Screen locking sounds
- Play a sound when locking and unlocking the screen (default – enabled).
• Charging sounds and vibration
- Plays a sound and vibrates when power is applied to the device
(default - enabled).
• Touch sounds
- Play a sound when making screen selections (default – disabled).
• Touch vibration
- Vibrate the device when making screen selections (default – disabled).
• Wireless Emergency alerts
- Touch to configure emergency broadcast settings and notifications.
Setting Wake-Up Sources
By default the device wakes from suspend mode when the user presses the
Power
button. The device can be configured to wake when the user presses the
PTT
or
Scan
buttons on the left side of the device.
1.
Go to
Settings
.
59
Settings
3.
4.
2.
Touch
Wake-Up Sources
.
• LEFT_TRIGGER_2
- PTT button.
• RIGHT_TRIGGER_1
- Right scan button.
• SCAN
- Left scan button.
Touch a checkbox. A check appears in the checkbox.
Touch the Home button.
Remapping a Button
Buttons on the device can be programmed to perform different functions or as shortcuts to installed apps. For a list of key names and descriptions, refer to: techdocs.zebra.com
.
NOTE:
It is not recommended to remap the scan button.
3.
4.
1.
2.
5.
Go to
Settings
.
Touch
Key Programmer
. A list of programmable buttons displays.
Select the button to remap.
Touch the
BUTTON REMAPPING
tab or the
SHORTCUT
tab that lists the available functions and applications.
Touch a function or application shortcut to map to the button.
NOTE:
If you select an application shortcut, the application icon appears next to the button on the Key
Programmer screen.
6.
7.
Touch the Home button.
If remapping the Back, Home, Search, or Menu button, perform a Soft Reset.
Keyboards
The device provides multiple keyboard options.
•
Android Keyboard - AOSP devices only
•
Gboard - GMS devices only
•
Enterprise Keyboard
NOTE:
By default the Enterprise and Virtual Keyboards are disabled.
Keyboard Configuration
Enabling Keyboards
1.
2.
3.
Go to
Settings
.
Touch
System
>
Languages & input
>
Virtual keyboard
>
Manage keyboards
.
Touch a keyboard to enable.
To enable a virtual keyboard like Gboard or Enterprise keyboard:
60
Settings
Switching Between Keyboards
•
To switch between keyboards, touch in a text box to display the current keyboard.
•
On the Gboard keyboard, touch and hold (GMS devices only).
•
On the Android keyboard, touch and hold (AOSP devices only).
•
On the Enterprise keyboard, touch . Only available with Mobility DNA Enterprise License.Not pre-installed on the device. Contact Zebra Support for more information.
Using the Android and Gboard Keyboards
Use the Android or Gboard keyboards to enter text in a text field.
•
To configure the keyboard settings, touch and hold
,
(comma) and then select
Android keyboard settings
.
Edit Text
Edit entered text and use menu commands to cut, copy, and paste text within or across apps. Some apps do not support editing some or all of the text they display; others may offer their own way to select text.
Entering Numbers, Symbols, and Special Characters
1.
2.
Enter numbers and symbols.
•
Touch and hold one of the top-row keys until a menu appears then select a number or special character.
•
Touch the Shift key once for a single capital letter. Touch the Shift key twice to lock in uppercase. Touch the Shift key a third time to unlock Capslock.
•
Touch
?123
to switch to the numbers and symbols keyboard.
•
Touch the
=\<
key on the numbers and symbols keyboard to view additional symbols.
Enter special characters.
•
Touch and hold a number or symbol key to open a menu of additional symbols. A larger version of the key displays briefly over the keyboard.
Using the Enterprise Keyboard
The Enterprise Keyboard contains multiple keyboard types.
•
Numeric
•
Alpha
•
Special characters
•
Data capture.
Numeric Tab
The numeric keyboard is labeled
123
. The keys displayed vary on the app being used. For example, an arrow displays in
Contacts
, however
Done
displays in
account setup.
Alpha Tab
The alpha keyboard is labeled using the language code. For English, the alpha keyboard is labeled
EN
.
61
Settings
Additional Character Tab
The additional characters keyboard is labeled
#*/
.
Touch to enter emoji icons in a text message.
Touch
ABC
to return to the Symbols keyboard.
Scan Tab
The Scan tab provides an easy data capture feature for scanning barcodes.
Language Usage
Use the
Language & input
settings to change the device’s language, including words added to the dictionary.
Changing the Language Setting
3.
4.
1.
2.
5.
6.
Go to
Settings
.
Touch
System
>
Languages & input
.
Touch
Languages
. A list of available languages displays.
If the desired language is not listed, touch
Add a language
and select a language from the list.
Touch and hold to the right of the desired language, then drag it to the top of the list.
The operating system text changes to the selected language.
Adding Words to the Dictionary
5.
6.
7.
3.
4.
1.
2.
Go to
Settings
.
Touch
System
>
Languages & input
>
Advanced
>
Personal dictionary
.
If prompted, select the language where this word or phase is stored.
Touch
+
to add a new word or phrase to the dictionary.
Enter the word or phrase.
In the
Shortcut
text box, enter a shortcut for the word or phrase.
Touch the Home button.
Notifications
Setting App Notifications
To set notification settings for a specific app:
1.
Go to
Settings
.
2.
3.
Touch
Apps & notifications
>
SEE ALL XX APPS
. The
App info
screen displays.
Select an app.
4.
Touch
Notifications
.
Options vary depending on the app selected.
62
Settings
5.
Select an available option:
Show notifications
- Select to turn all notifications from this app on (default) or off.
Touch a notification category to display additional options.
• Alerting
- Allow notifications from this app to make sound or vibrate the device.
• Pop on screen
- Allow notifications from this app to pop notifications on the screen.
• Silent
- Do not allow notifications from this app to make sound or vibrate.
• Minimize
- In the Notification panel, collapse notifications to one line.
• Advanced
- Touch for additional options.
• Sound
- Select a sound to play for notifications from this app.
• Vibrate
- Allow notifications from this app to vibrate the device.
• Blink light
- Allow notifications from this app the light the Notification LED blue.
• Show notification dot
- Allow notifications from this app to add a notification dot to the app icon.
• Override Do Not Disturb
- Allow these notifications to interrupt when Do Not Disturb is enabled.
Advanced
• Allow notification dot
- Do not allow this app to add a notification dot to the app icon.
• Additional settings in the app
- Open the app settings.
Viewing Notification Settings for All Apps
To view the notification settings for all apps:
1.
Go to
Settings
.
2.
3.
4.
Touch
Apps & Notifications
.
Scroll down to
Notifications
to view how many apps have notifications turned off.
To set or view notifications settings for a specific app, see Setting App Notifications.
Controlling Lock Screen Notifications
To control whether notifications can be seen when the device is locked:
1.
Go to
Settings
.
2.
3.
Touch
Apps & notifications
>
Notifications
.
Touch
Notifications on lockscreen
and select one of the following:
• Show alerting and silent notifications
(default)
• Show alerting notifications only
• Don’t show notifications.
Blink Light
The Notification LED lights blue when an app, such as email and VoIP, generates a programmable notification or to indicate when the device is connected to a Bluetooth device. By default, LED notifications are enabled.
To change the notification setting:
1.
Go to
Settings
.
63
Settings
2.
3.
Touch
Apps & notifications > Notifications > Advanced
.
Touch
Blink light
to toggle the notification on or off.
64
Applications
The
APPS
screen displays icons for all installed apps. See Application Deployment for information on installing and uninstalling apps. For information on standard Android apps, go to the Google Play Apps store .
The following table describes the apps installed on the device.
Table 7
Apps
Icon Description
Battery Manager
- Displays battery information, including charge level, status, health and wear level.
Bluetooth Pairing Utility
– Use to pair a Zebra Bluetooth scanner with the device by scanning a barcode.
Calculator
- Provides the basic and scientific arithmetic functions.
Calendar
- Use to manage events and appointments. GMS/GMS-Restricted only.
Calendar
- Use to manage events and appointments. AOSP only.
Camera
- Take photos or record videos. For more information, see Camera on page 71 .
Chrome
- Use to access the Internet or intranet. GMS/GMS-Restricted only.
Chromium
- Use to access the Internet or intranet. AOSP only.
Clock
- Use to schedule alarms for appointments or as a wake-up.
65
Applications
Table 7
Apps (Continued)
Icon Description
Contacts
- Use to manage contact information.
DataWedge
- Enables data capture using the imager. For more information, see DataWedge
.
DisplayLink Presenter
- Use to present the device screen onto a connected monitor.
Drive
- Upload photos, videos, documents, and other files to personal storage site.
GMS/GMS-Restricted only.
Duo
- A one-to-one video calling app. GMS/GMS-Restricted only.
DWDemo
- Provides a way to demonstrate the data capture features using the imager. For more information, see
DataWedge Demonstration on page 76 .
- Use to send and receive email. AOSP only.
Files
- Organize and manage files on the device.
Gallery
- Use to view photos stored on the microSD card. AOSP only.
Gmail
- Use to send and receive email using a Google email account. GMS/GMS-Restricted only.
- Launches Google ™ search app. GMS/GMS-Restricted only.
Keep Notes
- Use to create, edit, and share notes. GMS/GMS-Restricted only.
License Manager
- Use to manage software licenses on the device.
Maps
- Use to see your location on a map (with public transit, traffic, or satellite overlays).
Search for any business or place of interest. Provides turn-by-turn navigation with voice guidance, traffic-avoidance, and alternate routes, for drivers, cyclists, walkers, and users of public transportation. GMS/GMS-Restricted only.
66
Applications
Table 7
Apps (Continued)
Icon Description
MSRN
- Use to verify authenticity of the paired Snap-on MSR and to provision the Snap-on
MSR.
Music
- Play music stored on the microSD card. AOSP only.
Photos
- Use to sync photos with Google account. GMS/GMS-Restricted only.
Play Movies & TV
- View movies and video on your device. GMS/GMS-Restricted only.
Play Store
- Download music, movies, books, and Android apps and games from the
Google Play Store. GMS/GMS-Restricted only.
PTT Express
- Use to launch PTT Express client for VoIP communication.
RxLogger
- Use to diagnose device and app issues. For more information, see RxLogger on page 82 .
Search
- Use to search the Web. Requires an Internet connection. AOSP only.
Settings
- Use to configure the device.
Sound Recorder
- Use to record audio. For more information, see Sound Recorder on page 83 .
StageNow
- Allows the device to stage a device for initial use by initiating the deployment of settings, firmware, and software.
Worry Free Wifi Analyzer
- A diagnostic intelligent app. Use to diagnose surrounding area and display network stats, such as coverage hole detection, or AP in vicinity. Refer to the
Worry Free Wi-Fi Analyzer Administrator Guide for Android.
YouTube
- Use to view videos on the YouTube
™
web site. GMS/GMS-Restricted only.
67
Applications
Table 7
Apps (Continued)
Icon Description
YT Music
- Use to listen to music. GMS/GMS-Restricted only.
Zebra Bluetooth Settings
- Use to configure Bluetooth logging.
Zebra Data Services
- Use to enable or disable Zebra Data Services. Some options are set by the system administrator.
Accessing Apps
All apps installed on the device are accessed using the
APPS
window.
1.
On the Home screen, swipe up from the bottom of the screen.
2.
3.
Slide the
APPS
window up or down to view more app icons.
Touch an icon to open the app.
Switching Between Recent Apps
Use the Recent button to switch between recently used apps.
1.
Touch .
2.
3.
4.
A window appears on the screen with icons of recently used apps.
Slide the apps displayed up and down to view all recently used apps.
Swipe left or right to remove app from the list and force close the app.
Touch an icon to open an app or touch Back button to return to the current screen.
Battery Manager
The
Battery Manager
provides detailed information about the battery and battery swap procedures on supported devices.
Opening Battery Manager
To open the Battery Manager app, swipe up from the bottom of the Home screen, and then touch .
Battery Manager Information Tab
The Battery Manager displays detailed information about battery charging, health, and status.
68
Applications
Table 8
Battery Icon Description
Battery Icon Description
Battery charge level is between 85% and 100%.
Battery charge level is between 19% and 84%.
Battery charge level is between 0% and 18%.
• Level
- The current battery charge level as a percentage. Displays
-%
when level is unknown.
• Wear
- The health of the battery in graphical form. When the wear level exceeds 80%, the bar color changes to red.
• Health
- The health of the battery. If a critical error occurs, appears. Touch to view the error description.
• Decommission
- The battery is past its useful life and should be replaced. See system administrator.
• Good
- The battery is good.
• Charge error
- An error occurred while charging. See system administrator.
• Over Current
- An over-current condition occurred. See system administrator.
• Dead
- The battery has no charge. Replace the battery.
• Over Voltage
- An over-voltage condition occurred. See system administrator.
• Below Temperature
- The battery temperature is below the operating temperature. See system administrator.
• Failure Detected
- A failure has been detected in the battery. See system administrator.
• Unknown
- See system administrator.
• Charge Status
• Not charging
- The device is not connected to AC power.
• Charging-AC
- The device is connected to AC power and charging, or is fast charging via USB.
• Charging-USB
- The device is connected to a host computer with a USB cable and charging.
• Discharging
- The battery is discharging.
• Full
- That the battery is fully charged.
• Unknown
- The battery status is unknown.
• Time until Full
- The amount of time until the battery is fully charged.
• Time since charging
- The amount of time since the device began charging.
• Time until empty
- The amount of time until the battery is empty.
• Advanced info
- Touch to view additional battery information.
• Battery present status - Indicates that the battery is present.
69
Applications
• Battery level
- The battery charge level as a percentage of scale.
• Battery scale
- The battery scale level used to determine battery level (100).
• Battery voltage
- The current battery voltage in millivolts.
• Battery temperature
- The current battery temperature in degrees Centigrade.
• Battery technology
- The type of battery.
• Battery current
- The average current into or out of the battery over the last second in mAh.
• Battery manufacture date
- The date of manufacture.
• Battery serial number
- The battery serial number. The number matches the serial number printed on the battery label.
• Battery part number
- The battery part number.
• Battery decommission status
- Indicates if the battery is past its life span.
• Battery Good
- The battery is in good health.
• Decommissioned Battery
- The battery is past its useful life and should be replaced.
• Base cumulative charge
- Cumulative charge using Zebra charging equipment only.
• Battery present capacity
- Maximum amount of charge that could be pulled from the battery under the present discharge conditions if the battery were fully charged.
• Battery health percentage
- With a range from
0
to
100
, this is the ratio of “present_capacity” to
“design_capacity” at a discharge rate of “design_capacity”.
• % decommission threshold
- The default % decommission threshold for a gifted battery as 80%.
• Battery present charge
Amount of usable charge remaining in the battery at present under the current discharge conditions.
• Battery total cumulative charge
The total accumulated charge in all chargers.
• Battery time since first use
The time passed since the battery was placed in a Zebra terminal for the first time.
• Battery error status
- The error status of the battery.
• Battery usage number
- The health of the battery as a result of charging and discharging. A high number indicates low battery health.
• Usage decommission threshold
- When the Battery usage number is greater than or equal to the
Usage decommission threshold, the battery is past its useful life and should be replaced.
• App version
- The application version number.
Battery Manager Swap Tab
The
Swap
tab also appears when the uses presses the Power button and select
Battery Swap
.
Use to place the device in Battery Swap mode when replacing the battery. Follow the instructions on the screen. Touch
Proceed with battery swap
button.
70
Applications
Camera
NOTE:
The device saves photos and videos on the microSD card, if installed and the storage path is changed manually. By default, or if a microSD card is not installed, the device saves photos and videos on the internal storage.
This section provides information for taking photos and recording videos using the integrated digital cameras.
Taking Photos
NOTE:
See Photo Settings for camera setting descriptions.
1.
Swipe up from the bottom of the Home screen and touch
Camera
.
Filters
Scene Mode
Camera Switch
HDR
Settings
Gallery
Camera Mode
2.
3.
4.
5.
Shutter Button
If necessary, touch the Camera Mode icon and touch .
To switch between the rear camera and front camera (if available), touch .
Frame the subject on the screen.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
71
Applications
6.
7.
Touch an area on the screen to focus. The focus circle appears. The two bars turn green when in focus.
Touch .
The camera takes a photo and a shutter sound plays.
The photo momentarily displays as a thumbnail in the lower left corner.
Taking a Panoramic Photo
Panorama mode creates a single wide image by panning slowly across a scene.
1.
Swipe up from the bottom of the Home screen and touch
Camera
.
2.
3.
4.
5.
Touch the Camera Mode icon and touch .
Frame one side of the scene to capture.
Touch and slowly pan across the area to capture. A small white square appears inside the button indicating the capture is in progress.
If you are panning too quickly, the message
Too fast
appears.
Touch to end the shot. The panorama appears immediately and a progress indicator displays while it saves the image.
Recording Videos
1.
2.
Swipe up from the bottom of the Home screen and touch
Camera
.
Touch the camera mode menu and touch .
72
Color Effect
Applications
Camera Switch
Audio
Settings
Gallery
Camera Mode
Shutter Button
3.
4.
5.
To switch between the rear camera and front camera (if available), touch .
Point the camera and frame the scene.
To zoom in or out, press two fingers on the display and pinch or expand fingers. The zoom controls appear on the screen.
6.
Touch to start recording.
The video time remaining appears in the top left of the screen.
7.
Touch to end the recording.
The video momentarily displays as a thumbnail in the lower left corner.
Photo Settings
In Photo mode, photo settings appear on screen. Touch to display the photo settings options.
Rear Camera Photo Settings
• Flash
- Select whether the camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
•
•
Off
- Disable flash.
Auto
- Adjust flash automatically depending upon light meter (default).
On
- Enable flash upon taking a photo.
73
Applications
• Picture size
- The size (in pixels) of the photo to:
13M pixels
(default),
8M pixels
,
5M pixels
,
3M pixels
,
HD 1080
,
2M pixels
,
HD720
,
1M pixels
,
WVGA
,
VGA,
or
QVGA
.
• Picture quality
- Set the picture quality setting to:
Low
,
Standard
(default) or
High
.
• Countdown timer
- Select
Off
(default),
2 seconds
,
5 seconds
or
10 seconds
.
• Storage
– Set the location to store the photo to:
Phone
or
SD Card
.
• Continuous Shot
- Select to take a series of photos quickly while holding the capture button.
Off
(default) or
On
.
• Face Detection
- Set the camera to automatically adjust the focus for faces.
• ISO
- Set camera sensitivity to light to:
Auto
(default),
ISO Auto (HJR)
,
ISO100
,
ISO200
,
ISO400
,
ISO800
or
ISO1600
.
• Exposure
- Set the exposure settings to:
+2
,
+1
,
0
(default),
-1
or
-2
.
• White balance
- Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
•
•
•
Incandescent
Fluorescent
Auto
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
• Daylight
- Adjust the white balance for daylight.
• Cloudy
- Adjust the white balance for a cloudy environment.
• Redeye reduction
- Helps eliminate redeye effect. Options:
Disabled
(default), or
Enable
.
• ZSL
- Set the camera to immediately take a picture when the button is pressed (default – enabled).
• Shutter Sound
- Select to play a shutter sound when taking a photo. Options:
Disable
(default) or
Enable
.
• Anti Banding
- Allows the camera to avoid problems caused by artificial light sources that are not constant. These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options:
Auto
(default),
60 Hz
,
50
Hz
, or
Off
.
Front Camera Photo Settings
• Selfie Flash
- Turns screen white to help produce a little extra light in dimmer settings. Options:
Off
(default), or
On
.
• Picture size
- Set the size (in pixels) of the photo to:
5M pixels
(default),
3M pixels
,
HD1080
,
2M pixels
,
HD720
,
1M pixels
,
WVGA
,
VGA,
or
QVGA
.
• Picture quality
- Set the picture quality setting to:
Low
,
Standard
(default) or
High
.
• Countdown timer
- Set to:
Off
(default),
2 seconds
,
5 seconds
or
10 seconds
.
• Storage
– Set location to store the photo to:
Phone
or
SD Card
.
• Continuous Shot
- Select to take a series of photos quickly while holding the capture button.
Off
(default) or
On
.
• Face Detection
- Select to turn face detection
Off
(default) or
On
.
• ISO
- Set how sensitive the camera is to light. Options:
Auto
(default),
ISO Auto (HJR)
,
ISO100
,
ISO200
,
ISO400
,
ISO800
or
ISO1600
.
74
Applications
• Exposure
- Touch to adjust the exposure settings. Options:
+2
,
+1
,
0
(default),
-1
or
-2
.
• White balance
- Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors:
• Incandescent
- Adjust the white balance for incandescent lighting.
•
• Fluorescent
- Adjust the white balance for florescent lighting.
Auto
- Adjust the white balance automatically (default).
• Daylight
- Adjust the white balance for daylight.
• Cloudy
- Adjust the white balance for a cloudy environment.
• Redeye reduction
- Helps eliminate redeye effect. Options:
Disabled
(default), or
Enable
.
• ZSL
- Set the camera to immediately take a picture when the button is pressed (default – enabled)
• Selfie Mirror
- Select to save a mirror image of the photo. Options:
Disable
(default), or
Enable
.
• Shutter Sound
- Select to play a shutter sound when taking a photo. Options:
Disable
(default) or
Enable
.
• Anti Banding
- Allows the camera to avoid problems caused by artificial light sources that are not constant. These sources cycle (flicker) fast enough to go unnoticed to the human eye, appearing continuous. The camera’s eye (its sensor) can still see this flicker. Options:
Auto
(default),
60 Hz
,
50
Hz
, or
Off
.
Video Settings
In Video mode, video settings appear on screen. Touch to display the video settings options.
Rear Camera Video Settings
• Flash
- Select whether Rear-facing Camera relies on its light meter to decide whether a flash is necessary, or to turn it on or off for all shots.
•
•
•
•
•
• Off
- Disable flash (default).
• On
- Enable flash.
• Video quality
- Set video quality to:
4k DCI
,
4k UHD
,
HD 1080p
(default),
HD 720p
,
SD 480p, VGA,
CIF, or QVGA
.
• Video duration
- Set to:
30 seconds (MMS)
, or
30 minutes (default)
.
• Storage
– Set the location to store the photo to:
Phone
(default) or
SD Card
.
• White balance
- Select how the camera adjusts colors in different kinds of light, to achieve the most natural-looking colors.
Incandescent
Fluorescent
Auto
Daylight
Cloudy
- Adjust the white balance for incandescent lighting.
- Adjust the white balance for florescent lighting.
- Adjust the white balance automatically (default).
- Adjust the white balance for daylight.
- Adjust the white balance for a cloudy environment.
75
Applications
• Image Stabilization
- Set to reduce blurry videos due to device movement. Options:
On
or
Off
(default).
Front Camera Video Settings
• Video quality
- Set video quality to:
HD1080
(default),
HD 720p
(default),
HD720
, or
SD 480p
,
VGA
,
CIF
, or
QVGA
.
• Video duration
- Set to:
30 seconds (MMS)
, or
30 minutes
(default).
• Storage
– Set the location to store the photo to:
Phone
(default) or
SD Card
.
• Image Stabilization
- Set to reduce blurry videos due to device movement. Options:
On
or
Off
(default).
DataWedge Demonstration
Use
DataWedge Demonstration
to demonstrate data capture functionality. To configure DataWedge, refer to techdocs.zebra.com/datawedge/ .
DataWedge is disabled on the Home screen. To enable this feature, go to the DataWedge settings and enable Barcode input option.
Table 9
DataWedge Demonstration Icons
Icon
Illumination
Description
Imager illumination is on. Touch to turn illumination off.
Data Capture
Imager illumination is off. Touch to turn illumination on.
The data capture function is through the internal imager.
An RS507 or RS6000 Bluetooth imager is connected.
An RS507 or RS6000 Bluetooth imager is not connected.
Scan Mode
Menu
The data capture function is through the rear camera.
Imager is in picklist mode. Touch to change to normal scan mode.
Imager is in normal scan mode. Touch to change to picklist mode.
Opens a menu to view the application information or to set the application DataWedge profile.
Scanner Selection
To select a scanner, touch >
Settings
>
Scanner selection
.
See the Data Capture section for more information.
76
Applications
Press the programmable button or touch the yellow scan button to capture data. The data appears in the text field below the yellow button.
77
Applications
PTT Express Voice Client
NOTE:
Requires a PTT Express License.
PTT Express Voice Client enables Push-To-Talk (PTT) communication between disparate enterprise devices. Leveraging existing Wireless Local Area Network (WLAN) infrastructure, PTT Express delivers simple PTT communication without requiring a voice communication server.
• Group Call
: Press and hold the PTT (Talk) button to start communicating with other voice client users.
• Private Response
: Double-press the PTT button to respond to the originator of the last broadcast or to make a Private Response.
PTT Express User Interface
Figure 24
PTT Express Default User Interface
Notification Icon
Service Indication
Settings
Enable/Disable Switch
Talk Group
Table 10
PTT Express Default User Interface Descriptions
Item
Notification Icon
Service Indication
Talk Groups
Settings
Enable/Disable
Switch
Description
Indicates the current state of the PTT Express client.
Indicates the status of the PTT Express client. Options:
Service Enabled
,
Service Disabled
or
Service Unavailable
.
Lists all 32 Talk Groups available for PTT communication.
Opens the PTT Express Settings screen.
Turns the PTT service on and off.
78
Applications
PTT Audible Indicators
The following tones provide helpful cues when using the voice client.
• Talk Tone
: Double chirp. Plays when the Talk button is depressed. This is a prompt for you to start talking.
• Access Tone
: Single beep. Plays when another user just finished a broadcast or response. You can now initiate a Group Broadcast or Private Response.
• Busy Tone
: Continuous tone. Plays when the Talk button is depressed and another user is already communicating on the same talkgroup. Plays after the maximum allowed talk time is reached (60 seconds).
• Network Tone
:
•
Three increasing pitch beeps. Plays when PTT Express acquires the WLAN connection and the service is enabled.
•
Three decreasing pitch beeps. Plays when PTT Express loses the WLAN connection or the service is disabled.
PTT Notification Icons
Notification icons indicate the current state of the PTT Express Voice client.
Table 11
PTT Express Icon Descriptions
Status Icon Description
The PTT Express Voice client is disabled.
The PTT Express Voice client is enabled but not connected to a WLAN.
The PTT Express Voice client is enabled, connected to a WLAN, and listening on the
Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and communicating on the Talk Group indicated by the number next to the icon.
The PTT Express Voice client is enabled, connected to a WLAN, and in a private response.
The PTT Express Voice client is enabled and muted.
The PTT Express Voice client is enabled but it is not able to communicate due to a VoIP telephony call in progress.
Enabling PTT Communication
1.
2.
Swipe up from the bottom of the Home screen and touch .
Slide the
Enable/Disable Switch
to the
ON
position. The button changes to
ON
.
79
Applications
Selecting a Talk Group
One of 32 Talk Groups can be selected by PTT Express users. However, only one talk group may be enabled at a time on the device. Touch one of the 32 Talk Groups. The selected Talk Group is highlighted.
PTT Communication
NOTE:
This section describes the default PTT Express client configuration. Refer to the PTT Express V1.2
User Guide for detailed information on using the client.
PTT communication may be established as a Group Call. When PTT Express is enabled, the PTT button on the left side of the device is assigned for PTT communication. When the Wired Headset is used, Group
Calls can also be initiated using the headset Talk button.
Figure 25
PTT Button
1
1 PTT button
Creating a Group Call
1.
2.
Press and hold the PTT button (or the Talk button on the headset) and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that PTT Express and the WLAN are enabled.
Start talking after hearing the talk tone.
NOTE:
Holding the button for more than 60 seconds (default) drops the call, allowing others to make
Group calls. Release the button when finished talking to allow others to make calls.
Responding with a Private Response
The Private Response can only be initiated once a Group Call has been established. The initial Private
Response is made to the originator of the Group Call.
1.
Wait for an access tone.
80
Applications
4.
5.
2.
3.
Within 10 seconds, double-press the PTT button, and listen for the talk tone.
If you hear a busy tone, release the button and wait a moment before making another attempt. Ensure that PTT Express and the WLAN are enabled.
Start talking after the talk tone plays.
Release the button when finished talking.
Disabling PTT Communication
1.
2.
3.
Swipe up from the bottom of the Home screen and touch .
Slide the
Enable/Disable Switch
to the
OFF
position. The button changes to
OFF
.
Touch the Home button.
81
Applications
RxLogger
RxLogger is a comprehensive diagnostic tool that provides application and system metrics, allows for the creation of custom plug-ins, and diagnoses device and application issues. RxLogger logs the following information: CPU load, memory load, memory snapshots, battery consumption, power states, wireless logging, cellular logging, TCP dumps, Bluetooth logging, GPS logging, logcat, FTP push/pull, ANR dumps, etc. All generated logs and files are saved onto flash storage on the device (internal or external).
RxLogger Configuration
RxLogger is built with an extensible plug-in architecture and comes packaged with a number of plug-ins already built-in. For information on configuring RxLogger, refer to techdocs.zebra.com/rxlogger/ .
To open the configuration screen, from the RxLogger home screen touch
Settings
.
Configuration File
RxLogger configuration can be set using an XML file. The
config.xml
configuration file is located on the microSD card in the
RxLogger\config
folder. Copy the file from the device to a host computer using a USB connection. Edit the configuration file and then replace the XML file on the device. There is no need to stop and restart the RxLogger service since the file change is automatically detected.
Enabling Logging
To enable logging:
1.
2.
3.
Swipe the screen up and select .
Touch
Start
.
Touch the Home button.
Disabling Logging
1.
2.
3.
To disable logging:
Swipe the screen up and select .
Touch
Stop
.
Touch the Home button.
Extracting Log Files
3.
4.
1.
2.
Connect the device to a host computer using an USB connection.
Using a file explorer, navigate to the
RxLogger
folder.
Copy the file from the device to the host computer.
Disconnect the device from the host computer.
Backing Up
RxLogger Utility allows the user to make a zip file of the
RxLogger
folder in the device, which by default contains all the RxLogger logs stored in the device.
82
Applications
•
To save the backup data, touch >
BackupNow
.
RxLogger Utility
RxLogger Utility is a data monitoring application for viewing logs in the device while RxLogger is running.
Logs and RxLogger Utility features are accessed using Main Chat Head.
Initiating the Main Chat Head
To initiate the Main Chat Head:
1.
Open
RxLogger
.
2.
3.
Touch >
Toggle Chat Head
. The Main Chat Head icon appears on the screen.
Touch and drag the Main Chat head icon to move it around the screen.
Removing the Main Chat Head
To remove the Main Chat Head icon:
1.
Touch and drag the icon. A circle with an X appears.
2.
Move the icon over the circle and then release.
Viewing Logs
To view logs:
1.
Touch the Main Chat Head icon. The RxLogger Utility screen appears.
2.
3.
4.
Touch a log to open it. The user can open many logs with each displaying a new sub Chat Head.
If necessary, scroll left or right to view additional Sub Chat Head icons.
Touch a Sub Chat Head to display the log contents.
Removing a Sub Chat Head Icon
To remove a sub chat Head icon, press and hold the icon until it disappears.
Backing Up In Overlay View
1.
2.
RxLogger Utility allows the user to make a zip file of the
RxLogger
folder in the device, which by default contains all the RxLogger logs stored in the device.
The Backup icon is always available in Overlay View.
Touch . The Backup dialog box appears.
Touch
Yes
to create the back up.
Sound Recorder
Use
Sound Recorder
to record audio messages.
Recordings are saved on the microSD card (if installed) or the internal storage, and are available in the
Music application (AOSP devices) or the Play Music application (GMS devices).
Touch to open options menu.
83
Applications
• File type
- Select the file type for the recording file.
• AMR
• 3GPP
• AAC
• WAV
• AMR-WB
• AMR-WB-3GPP
.
• Storage location
- Select the location for the recording file.
• Phone storage
• SD card
84
Wireless
This section provides information on the following wireless features:
•
Wireless Local Area Network (WLAN)
•
Bluetooth
•
Cast
•
Near Field Communications (NFC)
Wireless Local Area Networks
Wireless local area networks (WLANs) allow the device to communicate wirelessly inside a building.
Before using the device on a WLAN, the facility must be set up with the required hardware to run the
WLAN (sometimes known as infrastructure). The infrastructure and the device must both be properly configured to enable this communication.
Refer to the documentation provided with the infrastructure (access points (APs), access ports, switches,
Radius servers, etc.) for instructions on how to set up the infrastructure.
Once the infrastructure is set up to enforce the chosen WLAN security scheme, use the
Wireless & networks
settings configure the device to match the security scheme.
The device supports the following WLAN security options:
•
Open
•
Wireless Equivalent Privacy (WEP)
•
Wi-Fi Protected Access (WPA)/WPA2 Personal (PSK)
•
WPA/WPA2/WPA3 Enterprise (EAP)
•
Protected Extensible Authentication Protocol (PEAP) - with MSCHAPV2 and GTC authentication.
•
Transport Layer Security (TLS)
•
Tunneled Transport Layer Security (TTLS) - with Password Authentication Protocol (PAP),
MSCHAP and MSCHAPv2 authentication
•
Password (PWD)
•
Lightweight Extensible Authentication Protocol (LEAP).
The
Status
bar displays icons that indicate Wi-Fi network availability and Wi-Fi status.
NOTE:
To extend the life of the battery, turn off Wi-Fi when not in use.
85
Wireless
Connecting to a Wi-Fi Network
To connect to a Wi-Fi network:
1.
Go to
Settings
.
2.
3.
Touch
Wi-Fi
to open the
Wi-Fi
screen. The device searches for WLANs in the area and lists them.
Scroll through the list and select the desired WLAN network.
4.
5.
For open networks, touch profile once or press and hold and then select
Connect
or for secure networks enter the required password or other credentials then touch
Connect
. See the system administrator for more information.
The device obtains a network address and other required information from the network using the dynamic host configuration protocol (DHCP) protocol. To configure the device with a fixed internet
protocol (IP) address, see Configuring the Device to Use a Static IP Address on page 89
.
In the Wi-Fi setting field,
Connected
appears indicating that the device is connected to the WLAN.
Removing a Wi-Fi Network
To remove a remembered or connected network:
1.
Go to
Settings
.
2.
3.
Touch
Network & Internet
>
W-Fi
.
Scroll down to the bottom of the list and touch
Saved networks
.
4.
5.
6.
Touch the name of the network.
Touch
FORGET
.
Touch the Home button.
WLAN Configuration
This section provides information on configuring Wi-Fi settings.
Configuring a Secure Wi-Fi Network
3.
4.
1.
2.
5.
6.
7.
8.
Go to
Settings
.
Touch
Network & Internet
>
Wi-Fi
.
Slide the switch to the
ON
position.
The device searches for WLANs in the area and lists them on the screen.
Scroll through the list and select the desired WLAN network.
Touch the desired network. If the network security is
Open
, the device automatically connects to the network. For all other network security a dialog box appears.
If the network security is WPA/WPA2-Personal, or WEP, enter the required password and then touch
Connect
.
If the network security is WPA/WPA2/WPA3 Enterprise:
•
Touch the
EAP method
drop-down list and select one of the following:
• TTLS
86
Wireless
• PWD
• LEAP
.
•
Touch the
Phase 2 authentication
drop-down list and select an authentication method.
•
If required, touch
CA certificate
and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the
Security
settings.
•
If required, touch
User certificate
and select a user certificate. Note: User certificates are installed using the Location & security settings.
•
If required, in the
Identity
text box, enter the username credentials.
•
If desired, in the
Anonymous identity
text box, enter an anonymous identity username.
•
If required, in the
Password
text box, enter the password for then given identity.
NOTE:
By default, the network Proxy is set to
None
and the IP settings is set to
DHCP
. See Configuring for a Proxy Server for setting connection to a proxy server and see Configuring the Device to Use a Static
IP Address for setting the device to use a static IP address.
9.
Touch
Connect
.
10.
Touch the Home button.
Manually Adding a Wi-Fi Network
Manually add a Wi-Fi network if the network does not broadcast its name (SSID) or to add a Wi-Fi network when out of range.
1.
2.
Go to
Settings
.
Touch
Network & Internet
>
Wi-Fi
.
3.
4.
5.
6.
Slide the Wi-Fi switch to the
On
position.
Scroll to the bottom of the list and select
Add network
.
In the
Network name
text box, enter the name of the Wi-Fi network.
In the
Security
drop-down list, set the type of security to:
7.
8.
• None
• WEP
• WPA/WPA2-Personal
• WPA/WPA2/WPA3-Enterprise
If the network security is
None
, touch
Save
.
If the network security is
WEP,
or
WPA/WPA2-Personal
, enter the required password and then touch
Save
.
9.
If the network security is
WPA/WPA2/WPA3-Enterprise
:
•
Touch the
EAP method
drop-down list and select one of the following:
• PEAP
• TLS
• TTLS
• PWD
• LEAP.
87
Wireless
•
Touch the
Phase 2 authentication
drop-down list and select an authentication method.
•
If required, touch
CA certificate
and select a Certification Authority (CA) certificate. Note:
Certificates are installed using the
Security
settings.
•
If required, touch
User certificate
and select a user certificate. Note: User certificates are installed using the
Security
settings.
•
If required, in the
Identity
text box, enter the username credentials.
•
If desired, in the
Anonymous identity
text box, enter an anonymous identity username.
•
If required, in the
Password
text box, enter the password for the given identity.
NOTE:
By default, the network Proxy is set to
None
and the IP settings is set to
DHCP
. See Configuring for a Proxy Server on page 88
for setting connection to a proxy server and see Configuring the Device to
Use a Static IP Address on page 89 for setting the device to use a static IP address.
10.
Touch
Save
. To connect to the saved network, touch and hold on the saved network and select
Connect to network
.
11.
Touch the Home button.
Configuring for a Proxy Server
A proxy server is a server that acts as an intermediary for requests from clients seeking resources from other servers. A client connects to the proxy server and requests some service, such as a file, connection, web page, or other resource, available from a different server. The proxy server evaluates the request according to its filtering rules. For example, it may filter traffic by IP address or protocol. If the request is validated by the filter, the proxy provides the resource by connecting to the relevant server and requesting the service on behalf of the client.
It is important for enterprise customers to be able to set up secure computing environments within their companies, making proxy configuration essential. Proxy configuration acts as a security barrier ensuring that the proxy server monitors all traffic between the Internet and the intranet. This is normally an integral part of security enforcement in corporate firewalls within intranets.
1.
2.
3.
4.
Go to
Settings
.
Touch
Network & Internet
>
Wi-Fi
.
Slide the Wi-Fi switch to the
On
position.
In the network dialog box, select and touch a network.
5.
6.
7.
8.
Touch
Advanced options
.
Touch
Proxy
and select
Manual
.
In the
Proxy hostname
text box, enter the address of the proxy server.
In the
Proxy port
text box, enter the port number for the proxy server.
9.
In the
Bypass proxy for
text box, enter addresses for web sites that are not required to go through the proxy server. Use a comma “,” between addresses. Do not use spaces or carriage returns between addresses.
10.
Touch
Connect
.
11.
Touch the Home button.
88
Wireless
Configuring the Device to Use a Static IP Address
By default, the device is configured to use Dynamic Host Configuration Protocol (DHCP) to assign an
Internet protocol (IP) address when connecting to a wireless network.
1.
2.
Go to
Settings
.
Touch
Network & Internet
>
Wi-Fi
.
3.
4.
Slide the Wi-Fi switch to the
On
position.
In the network dialog box, select and touch a network.
5.
6.
7.
8.
9.
Touch
Advanced options
.
Touch
IP settings
and select
Static
.
In the
IP address
text box, enter an IP address for the device.
If required, in the
Gateway
text box, enter a gateway address for the device.
10.
If required, in the
Network prefix length
text box, enter the prefix length.
11.
If required, in the
DNS 1
text box, enter a Domain Name System (DNS) address.
12.
If required, in the
DNS 2
text box, enter a DNS address.
13.
Touch
Connect
.
14.
Touch the Home button.
Wi-Fi Preferences
Use the
Wi-Fi preferences
to configure advanced Wi-Fi settings. From the Wi-Fi screen scroll down to the bottom of the screen and touch
Wi-Fi preferences
.
• Turn on Wi-Fi automatically
- When enabled, Wi-Fi automatically turns back on when near high quality saved networks.
• Open network notification
- When enabled, notifies the user when an open network is available.
• Advanced
- Touch to expand options.
• Additional settings
- See Additional Settings.
• Install Certificates
– Touch to install certificates.
• Network rating provider
- Disabled (AOSP devices). To help determine what constitutes a good
Wi-Fi network, Android supports external Network rating providers that provide information about the quality of open Wi-Fi networks. Select one of the providers listed or
None
. If none are available or selected, the Connect to open networks feature is disabled.
• Wi-Fi Direct
- Displays a list of devices available for a direct Wi-Fi connection.
• MAC address
- Displays the Media Access Control (MAC) address of the device when connecting to Wi-Fi networks.
• IP address
- Displays the IP address of the device when connecting to Wi-Fi networks.
Additional Wi-Fi Settings
NOTE:
Additional Wi-Fi settings are for the device, not for a specific wireless network.
89
Wireless
Use the
Additional Settings
to configure additional Wi-Fi settings. To view the additional Wi-Fi settings, scroll to the bottom of the
Wi-Fi
screen and touch
Wi-Fi Preferences
>
Advanced
>
Additional settings.
• Regulatory
• Country Selection
- Displays the acquired country code if 802.11d is enabled, else it displays the currently selected country code.
• Region code
- Displays the current region code.
• Band and Channel Selection
• Wi-Fi frequency band
- Set the frequency band to:
Auto
(default),
5 GHz only
or
2.4 GHz only
.
• Available channels (2.4 GHz)
- Touch to display the
Available channels
menu. Select specific channels and touch
OK
.
• Available channels (5 GHz)
- Touch to display the
Available channels
menu. Select specific channels and touch
OK
.
• Logging
• Advanced Logging
– Touch to enable advanced logging or change the log directory.
• Wireless logs
- Use to capture Wi-Fi log files.
• Fusion Logger
- Touch to open the
Fusion Logger
application. This application maintains a history of high level WLAN events which helps to understand the status of connectivity.
• Fusion Status
- Touch to display live status of WLAN state. Also provides information about the device and connected profile.
• About
• Version
- Displays the current Fusion information.
Wi-Fi Direct
Wi-Fi Direct devices can connect to each other without having to go through an access point. Wi-Fi Direct devices establish their own ad-hoc network when required, letting you see which devices are available and choose which one you want to connect to.
1.
2.
Go to
Settings
.
Touch
Wi-Fi
>
Wi-Fi preferences
>
Advanced
>
Wi-Fi Direct
. The device begins searching for another Wi-Fi Direct device.
3.
4.
Under
Peer devices
, touch the other device name.
On the other device, select
Accept
.
Connected
appears on the device. On both devices, in their respective Wi-Fi Direct screens, the other device name appears in the list.
Bluetooth
Bluetooth devices can communicate without wires, using frequency-hopping spread spectrum (FHSS) radio frequency (RF) to transmit and receive data in the 2.4 GHz Industry Scientific and Medical (ISM) band (802.15.1). Bluetooth wireless technology is specifically designed for short-range (10 m (32.8 ft)) communication and low power consumption.
Devices with Bluetooth capabilities can exchange information (for example, files, appointments, and tasks) with other Bluetooth enabled devices such as printers, access points, and other mobile devices.
90
Wireless
The device supports Bluetooth Low Energy. Bluetooth Low Energy is targeted at applications in the healthcare, fitness, security, and home entertainment industries. It provides reduced power consumption and cost while maintaining standard Bluetooth range.
Adaptive Frequency Hopping
Adaptive Frequency Hopping (AFH) is a method of avoiding fixed frequency interferers, and can be used with Bluetooth voice. All devices in the piconet (Bluetooth network) must be AFH-capable in order for AFH to work. There is no AFH when connecting and discovering devices. Avoid making Bluetooth connections and discoveries during critical 802.11b communications. AFH for Bluetooth consists of four main sections:
•
Channel Classification - A method of detecting an interference on a channel-by-channel basis, or pre-defined channel mask.
•
Link Management - Coordinates and distributes the AFH information to the rest of the Bluetooth network.
•
Hop Sequence Modification - Avoids interference by selectively reducing the number of hopping channels.
•
Channel Maintenance - A method for periodically re-evaluating the channels.
When AFH is enabled, the Bluetooth radio “hops around” (instead of through) the 802.11b high-rate channels. AFH coexistence allows enterprise devices to operate in any infrastructure.
The Bluetooth radio in this device operates as a Class 2 device power class. The maximum output power is 2.5 mW and the expected range is 10 m (32.8 ft). A definition of ranges based on power class is difficult to obtain due to power and device differences, and whether in open space or closed office space.
NOTE:
It is not recommended to perform Bluetooth wireless technology inquiry when high rate 802.11b operation is required.
Security
The current Bluetooth specification defines security at the link level. Application-level security is not specified. This allows application developers to define security mechanisms tailored to their specific need.
Link-level security occurs between devices, not users, while application-level security can be implemented on a per-user basis. The Bluetooth specification defines security algorithms and procedures required to authenticate devices, and if needed, encrypt the data flowing on the link between the devices. Device authentication is a mandatory feature of Bluetooth while link encryption is optional.
Pairing of Bluetooth devices is accomplished by creating an initialization key used to authenticate the devices and create a link key for them. Entering a common personal identification number (PIN) in the devices being paired generates the initialization key. The PIN is never sent over the air. By default, the
Bluetooth stack responds with no key when a key is requested (it is up to user to respond to the key request event). Authentication of Bluetooth devices is based-upon a challenge-response transaction.
Bluetooth allows for a PIN or passkey used to create other 128-bit keys used for security and encryption.
The encryption key is derived from the link key used to authenticate the pairing devices. Also worthy of note is the limited range and fast frequency hopping of the Bluetooth radios that makes long-distance eavesdropping difficult.
Recommendations are:
•
Perform pairing in a secure environment
•
Keep PIN codes private and do not store the PIN codes in the device
•
Implement application-level security.
91
Wireless
Bluetooth Profiles
The device supports the Bluetooth services listed.
Table 12
Bluetooth Profiles
Profile
Service Discovery Protocol
(SDP)
Serial Port Profile (SPP)
Object Push Profile (OPP)
Advanced Audio Distribution
Profile (A2DP)
Audio/Video Remote Control
Profile (AVRCP)
Personal Area Network (PAN)
Human Interface Device Profile
(HID)
Headset Profile (HSP)
Hands-Free Profile (HFP)
Phone Book Access Profile
(PBAP)
Out of Band (OOB)
Symbol Serial Interface (SSI)
Description
Handles the search for known and specific services as well as general services.
Allows use of RFCOMM protocol to emulate serial cable connection between two Bluetooth peer devices. For example, connecting the device to a printer.
Allows the device to push and pull objects to and from a push server.
Allows the device to stream stereo-quality audio to a wireless headset or wireless stereo speakers.
Allows the device to control A/V equipment to which a user has access. It may be used in concert with A2DP.
Allows the use of Bluetooth Network Encapsulation Protocol to provide L3 networking capabilities over a Bluetooth link. Only
PANU role is supported.
Allows Bluetooth keyboards, pointing devices, gaming devices and remote monitoring devices to connect to the device.
Allows a hands-free device, such as a Bluetooth headset, to place and receive calls on the device.
Allows car hands-free kits to communicate with the device in the car.
Allows exchange of Phone Book Objects between a car kit and a mobile device to allow the car kit to display the name of the incoming caller; allow the car kit to download the phone book so you can initiate a call from the car display.
Allows exchange of information used in the pairing process. Pairing is completed using the Bluetooth radio, but requires information from the OOB mechanism. Using OOB with NFC enables pairing when devices simply get close, rather than requiring a lengthy discovery process.
Allows for communication with Bluetooth Imager.
Bluetooth Power States
The Bluetooth radio is off by default.
•
Suspend - When the device goes into suspend mode, the Bluetooth radio stays on.
•
Airplane Mode - When the device is placed in Airplane Mode, the Bluetooth radio turns off. When
Airplane mode is disabled, the Bluetooth radio returns to the prior state. When in Airplane Mode, the
Bluetooth radio can be turned back on if desired.
92
Wireless
Bluetooth Radio Power
Turn off the Bluetooth radio to save power or if entering an area with radio restrictions (for example, an airplane). When the radio is off, other Bluetooth devices cannot see or connect to the device. Turn on the
Bluetooth radio to exchange information with other Bluetooth devices (within range). Communicate only with Bluetooth radios in close proximity.
NOTE:
To achieve the best battery life, turn off radios when not in use.
Enabling Bluetooth
1.
2.
3.
Swipe down from the Status bar to open the Notification panel.
Touch to turn Bluetooth on.
Touch the Home button.
Disabling Bluetooth
1.
2.
3.
Swipe down from the Status bar to open the Notification panel.
Touch to turn Bluetooth off.
Touch the Home button.
Discovering Bluetooth Device(s)
The device can receive information from discovered devices without pairing. However, once paired, the device and a paired device exchange information automatically when the Bluetooth radio is on.
1.
2.
Ensure that Bluetooth is enabled on both devices.
Ensure that the Bluetooth device to discover is in discoverable mode.
3.
4.
5.
6.
7.
8.
9.
Ensure that the two devices are within 10 meters (32.8 feet) of one another.
Swipe down from the Status bar to open the Quick Access panel.
Touch and hold
Bluetooth
.
Touch
Pair new device
. The device begins searching for discoverable Bluetooth devices in the area and displays them under
Available devices
.
Scroll through the list and select a device. The Bluetooth pairing request dialog box appears.
Touch
Pair
on both devices.
The Bluetooth device is added to the
Paired devices
list and a trusted (“paired”) connection is established.
Changing the Bluetooth Name
By default, the device has a generic Bluetooth name that is visible to other devices when connected.
1.
Go to
Settings
.
2.
3.
4.
Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
If Bluetooth is not on, move the switch to turn Bluetooth on.
Touch
Device name
.
93
Wireless
5.
6.
Enter a name and touch
RENAME
.
Touch the Home button.
Connecting to a Bluetooth Device
Once paired, connect to a Bluetooth device.
1.
Go to
Settings
.
2.
3.
Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
In the list, touch the unconnected Bluetooth device.
When connected,
Connected
appears below the device name.
Selecting Profiles on the Bluetooth Device
Some Bluetooth devices have multiple profiles.
1.
Go to
Settings
.
2.
Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3.
4.
5.
In the
Paired Devices
list, touch next to the device name.
Turn on or off a profile to allow the device to use that profile.
Touch the Home button.
Unpairing a Bluetooth Device
Unpairing a Bluetooth device erases all pairing information.
1.
Go to
Settings
.
2.
Touch
Connected devices
>
Connection preferences
>
Bluetooth
.
3.
4.
5.
In the
Paired Devices
list, touch next to the device name.
Touch
FORGET
.
Touch the Home button.
Cast
Use
Cast
to mirror the device screen on a Miracast enabled wireless display.
1.
Go to
Settings
.
2.
Touch
Connected devices
>
Connection preferences
>
Cast
.
3.
4.
5.
Touch >
Enable wireless display
.
The device searches for nearby Miracast devices and lists them.
Touch a device to begin casting.
Touch the Home button.
94
Wireless
Near Field Communications
NFC/HF RFID is a short-range wireless connectivity technology standard that enables secure transaction between a reader and a contactless smartcard. The technology is based on ISO/IEC 14443 type A and B
(proximity) and ISO/IEC 15693 (vicinity) standards, using the HF 13.56 MHz unlicensed band.
The device supports the following operating modes:
•
Reader mode
•
Peer-to-Peer communication
•
Card Emulation mode.
Using NFC, the device can:
•
Read contactless cards such as contactless tickets, ID cards and ePassport.
•
Read and write information to contactless cards such as SmartPosters and tickets, as well as devices with NFC interface such as vending machines.
•
Read information from supported medical sensors.
•
Pair with supported Bluetooth devices such as printers , ring scanners (ex. RS6000), and headsets (ex.
HS3100).
•
Exchange data with another NFC device.
•
Emulate contactless card such as payment, ticket, or SmartPoster.
The device NFC antenna is positioned to read NFC cards from the top of the device while the device is being held.
The device NFC antenna is located on the back of the device, near the Interface Connector.
Reading NFC Cards
Read contactless cards using NFC.
Figure 26
Reading Cards
1.
2.
Launch an NFC enabled application.
Hold device as shown.
95
Wireless
3.
4.
Move the device close to the NFC card until it detects the card.
Hold the card steadily until the transaction is complete (usually indicated by the application).
Sharing Information Using NFC
You can beam content like a web page, contact cards, pictures, YouTube links or location information from your screen to another device by bringing the devices together back to back.
Make sure both devices are unlocked, support NFC, and have both NFC and Android Beam turned on.
1.
Open a screen that contains a web page, video, photo or contact.
2.
3.
4.
Move the back of the device toward the back of the other device.
Align the NFC logo on the device with the NFC antenna on the other device.
Move the front of the device toward the front of the other device.
When the devices connect, a sound emits, the image on the screen reduces in size, the message
Touch to beam
displays.
Figure 27
NFC Antenna
5.
Touch anywhere on the screen.
The transfer begins.
Enterprise NFC Settings
Improve NFC performance or increase battery life by selecting which NFC features to use on the device.
• Card Detection Mode
- Select a card detection mode.
• Low
- Increases battery life by lowering the NFC detection speed.
• Hybrid
- Provides a balance between NFC detection speed and battery life (default).
• Standard
- Provides the best NFC detection speed, but reduces battery life.
• Supported Card Technology
- Select an option to detect only one NFC tag type, increasing battery life, but reducing detection speed.
• All (Default)
- Detects all NFC tag types. This provides the best detection speed, but reduces battery life.
• ISO 14443 Type A/B
96
Wireless
• FeliCa
• ISO15693
• Other NFC settings available with Zebra administrator tools (CSP)
- Allows configuration of additional Enterprise NFC Settings through staging tools and Mobile Device Management (MDM) solutions with an MX version that supports the Enterprise NFC Settings Configuration Service Provider
(CSP). For more information on using the Enterprise NFC Settings CSP, refer to: techdocs.zebra.com
.
97
Accessories
This table lists the accessories available for the device.
Table 13
Accessories
Accessory
Cradles
2-Slot Charge Only
Cradle
2-Slot USB/Ethernet
Cradle
Part Number
CRD-TC7X-SE2CPP-01
CRD-TC7X-SE2EPP-01
5-Slot Charge Only
Cradle
5-Slot Ethernet Cradle
Cradle Mount
CRD-TC7X-SE5C1-01
CRD-TC7X-SE5EU1–01
BRKT-SCRD-SMRK-01
Description
Provides device and spare battery charging. Use with power supply, p/n
PWR-BGA12V50W0WW.
Provides device and spare battery charging and USB communication with a host computer and Ethernet communication with a network. Use with power supply, p/n
PWR-BGA12V50W0WW.
Charges up to five devices. Use with power supply, p/n PWR-BGA12V108W0WW and
DC line cord, p/n CBL-DC-381A1-01. Can accommodate one 4-Slot Battery Charger using the Battery Adapter Cup.
Provides device charging and provides
Ethernet communication for up to five devices. Use with power supply, p/n
PWR-BGA12V108W0WW and DC line cord, p/n CBL-DC-381A1-01. Can accommodate one 4-Slot Battery Charger using the Battery Adapter Cup.
Mounts the 5-Slot Charge Only Cradle,
5-Slot Ethernet Cradle, and 4-Slot Battery
Charger to a wall or rack.
Batteries and Chargers
4,620 mAh
PowerPrecision+ battery
4-Slot Spare Battery
Charger
BTRY-TC7X-46MPP-01
BTRY-TC7X-46MPP-10
SAC-TC7X-4BTYPP-01
Replacement battery (single pack).
Replacement battery (10–pack).
Charges up to four battery packs. Use with power supply, p/n
PWR-BGA12V50W0WW.
98
Accessories
Table 13
Accessories (Continued)
Accessory
Battery Charger Adapter
Cup
Part Number
CUP-SE-BTYADP1-01
Description
Allows for one 4-Slot Battery Charger to be charged and docked on the left most slot of the 5-Slot cradles (maximum one per cradle).
Vehicle Solutions
Charging Cable Cup
Charge Only Vehicle
Cradle
TC7X Data
Communication Enabled
Vehicle Cradle with Hub
Kit
Cigarette Light Adapter
Auto Charge Cable
Hard-wire Auto Charge
Cable
RAM Mount
CRD-TC7X-VCD1-01
CHG-AUTO-CLA1-01
CHG-AUTO-HWIRE1-01
RAM-B-166U
RAM Mount Base
CHG-TC7X-CLA1-01
CRD-TC7X-CVCD1-01
RAM-B-238U
Charge and Communication Cables
Charging Cable Cup CHG-TC7X-CBL1-01
Provides power to the device from a cigarette lighter socket.
Charges and securely holds the device.
Requires power cable
CHG-AUTO-CLA1-01 or
CHG-AUTO-HWIRE1-01, sold separately.
Contains the TC7X Vehicle
Communication Charging Cradle and the
USB I/O Hub.
Provides power to the Vehicle Cradle from a cigarette lighter socket.
Provides power to the Vehicle Cradle from the vehicle's power panel.
Provides window mounting option for the
Vehicle Cradle. RAM Twist Lock Suction
Cup with Double Socket Arm and Diamond
Base Adapter. Overall Length: 6.75”.
RAM 2.43" x 1.31" Diamond Ball base with
1" ball.
Snap-On USB Cable
MSR Adapter
Snap-On DEX Cable
Audio Accessories
Rugged Headset
CBL-TC7X-USB1-01
MSR-TC7X-SNP1-01
CBL-TC7X-DEX1-01
HS2100-OTH
Provides power to the device. Use with power supply, p/n PWR-BUA5V16W0WW, sold separately.
Provides power to the device and USB communication with a host computer. Use with power supply, p/n
PWR-BUA5V16W0WW, sold separately.
Provides power and USB communication with a host computer. Use with USB-C cable, sold separately.
Provides electronic data exchange with devices such as vending machines.
Bluetooth Headset HS3100-OTH
Rugged wired headset. Includes HS2100
Boom Module and HSX100 OTH
Headband Module.
Rugged Bluetooth Headset. Includes
HS3100 Boom Module and HSX100 OTH
Headband Module.
99
Accessories
Table 13
Accessories (Continued)
Accessory
3.5 mm Audio Adapter
Part Number
ADP-TC7X-AUD35-01
3.5 mm Headset
3.5 mm Quick
Disconnect Adapter
Cable
Scanning
Trigger Handle
HDST-35MM-PTVP-01
ADP-35M-QDCBL1-01
TRG-TC7X-SNP1-02
Snaps onto the device and provides audio to a wired headset with 3.5 mm plug.
Use for PTT and VoIP calls.
Provides connection to the 3.5 mm
Headset.
Description
Trigger Handle Attach
Plate with Tether
Trigger Handle Attach
Plate
ADP-TC7X-CLHTH-10
ADP-TC7X-CLPTH1-20
Adds gun-style handle with a scanner trigger for comfortable and productive scanning.
Trigger Handle Attach Plate with tether.
Allows for installation of the Trigger Handle
(10-pack). Use with charge only cradles.
Trigger Handle Attach Plate. Allows for installation of the Trigger Handle
(20-pack). Use with Ethernet and charge only cradles.
Carrying Solutions
Soft Holster
Rigid Holster
Hand Strap
SG-TC7X-HLSTR1-02
SG-TC7X-RHLSTR1-01
SG-TC7X-HSTRP2-03
Stylus and Coiled Tether SG-TC7X-STYLUS-03
Screen Protector SG-TC7X-SCRNTMP-01
Power Supplies
Power Supply PWR-BUA5V16W0WW
Power Supply
TC7X soft holster.
TC7X rigid holster.
Replacement hand strap with hand strap mounting clip (3–pack).
TC7X stylus with coiled tether (3-pack).
Provides additional protection for the screen (1-pack).
PWR-BGA12V50W0WW
Provides power to the device using the
Snap-On USB Cable, Snap-on Serial
Cable or Charging Cable Cup. Requires
DC Line Cord, p/n DC-383A1-01 and country specific three wire grounded AC line cord sold separately.
Provides power to the 2–Slot cradles and
4-Slot Spare Battery Charger. Requires
DC Line Cord, p/n CBL-DC-388A1-01 and country specific three wire grounded AC line cord sold separately.
100
Accessories
Table 13
Accessories (Continued)
Accessory
Power Supply
DC Line Cord
DC Line Cord
Part Number
PWR-BGA12V108W0WW Provides power to the 5-Slot Charge Only cradle and the 5-Slot Ethernet Cradle.
Requires DC Line Cord, p/n
CBL-DC-381A1-01 and country specific three wire grounded AC line cord sold separately.
CBL-DC-388A1-01
CBL-DC-381A1-01
Description
Provides power from the power supply to the 2-Slot cradles and 4-Slot Spare Battery
Charger.
Provides power from the power supply to the 5-Slot Charge Only Cradle and 5-Slot
Ethernet Cradle.
Battery Charging
Main Battery Charging
The device’s Charging/Notification LED indicates the status of the battery charging in the device.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Spare Battery Charging
The Spare battery Charging LED on the cup indicates the status of the spare battery charging.
The 4,620 mAh battery fully charges in less than five hours at room temperature.
Table 14
Spare Battery Charging LED Indicators
LED
Slow Blinking Amber
Solid Green
Fast Blinking Amber
Slow Blinking Red
Solid Red
Fast Blinking Red
Off
Indication
Spare battery is charging.
Charging complete.
Error in charging; check placement of spare battery.
Spare battery is charging and battery is at the end of useful life.
Charging complete and battery is at the end of useful life.
Error in charging; check placement of spare battery and battery is at the end of useful life.
No spare battery in slot; spare battery not placed correctly; cradle is not powered.
101
Accessories
Charging Temperature
Charge batteries in temperatures from 0°C to 40°C (32°F to 104°F). The device or cradle always performs battery charging in a safe and intelligent manner. At higher temperatures (e.g. approximately +37°C
(+98°F)) the device or cradle may for small periods of time alternately enable and disable battery charging to keep the battery at acceptable temperatures. The device and cradle indicates when charging is disabled due to abnormal temperatures via its LED.
2-Slot Charge Only Cradle
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
The 2-Slot Charge Only Cradle:
•
Provides 5 VDC power for operating the device.
•
Charges the device’s battery.
•
Charges a spare battery.
Figure 28
2–Slot Charge Only Cradle
Spare Battery
Charging LED
Power LED
102
Accessories
Setup
Figure 29
2–Slot Charge Only Cradle
Charging the Device
1.
Insert the device into the slot to begin charging.
103
Accessories
2.
Ensure the device is seated properly.
Charging the Spare Battery
1.
Insert the battery into the right slot to begin charging.
2.
Ensure the battery is seated properly.
104
Accessories
2-Slot USB/Ethernet Cradle
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
The 2-Slot USB/Ethernet Cradle:
•
Provides 5.0 VDC power for operating the device.
•
Charges the device’s battery.
•
Charges a spare battery.
•
Connects the device to an Ethernet network.
•
Provides communication to a host computer using a USB cable.
NOTE:
Remove all attachments on the device, except the hand strap, before place onto the cradle.
Figure 30
2-Slot USB/Ethernet Cradle
Spare Battery
Charging LED
Power LED
105
Accessories
Setup
Figure 31
2–Slot USB/Ethernet Cradle
Charging the Device
1.
Place the bottom of the device into the base.
106
Accessories
2.
3.
Rotate the top of the device until the connector on the back of the device mates with the connector on the cradle.
Ensure the device is connected properly. The charging Charging/Notification LED on the device begins blinking amber indicating that the device is charging.
Charging the Spare Battery
1.
Insert the battery into the right slot to begin charging.
Figure 32
Spare Battery Charging
107
Accessories
2.
Ensure the battery is seated properly.
USB/Ethernet Communication
The 2–Slot USB/Ethernet Cradle provides both Ethernet communication with a network and USB communication with a host computer. Prior to using the cradle for Ethernet or USB communication. Ensure that the switch on the USB/Ethernet module is set properly.
Turn the cradle over to view the module.
Figure 33
2–Slot USB/Ethernet Cradle Module Switch
For Ethernet communication, slide the switch to the position.
For USB communication, slide the switch to the position.
Place the switch in the center position to disable communications.
Ethernet LED Indicators
There are two LEDs on the USB/Ethernet Module RJ-45 connector. The green LED lights to indicate that the transfer rate is 100 Mbps. When the LED is not lit the transfer rate is 10 Mbps. The yellow LED blinks to indicate activity, or stays lit to indicate that a link is established. When it is not lit it indicates that there is no link.
Figure 34
LED Indicators
Yellow LED Green LED
Table 15
USB/Ethernet Module LED Data Rate Indicators
Data Rate Yellow LED
100 Mbps
10 Mbps
On/Blink
On/Blink
On
Off
Green LED
Establishing Ethernet Connection
1.
2.
3.
Swipe down from the Status bar to open the Quick Access panel and then touch .
Touch
Ethernet
.
Slide the Ethernet switch to the
ON
position.
108
Accessories
4.
5.
Insert the device into a slot.
The icon appears in the Status bar.
Touch
Eth0
to view Ethernet connection details.
Ethernet Settings
The following settings can be configured when using Ethernet communication:
•
Proxy Settings
•
Static IP.
Configuring Ethernet Proxy Settings
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1.
2.
3.
4.
5.
6.
7.
8.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch
Network & Internet
.
Touch
Ethernet
.
Place the device into the Ethernet cradle slot.
Slide the switch to the
ON
position.
Touch and hold
Eth0
until the menu appears.
Touch
Modify Proxy
.
Touch the
Proxy
drop-down list and select
Manual
.
9.
In the
Proxy hostname
field, enter the proxy server address.
10.
In the
Proxy port
field, enter the proxy server port number.
NOTE:
When entering proxy addresses in the Bypass proxy for field, do not use spaces or carriage returns between addresses.
11.
In the
Bypass proxy for
text box, enter addresses for web sites that do not require to go through the proxy server. Use the separator “|” between addresses.
12.
Touch
MODIFY
.
13.
Touch .
Configuring Ethernet Static IP Address
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1.
2.
3.
4.
5.
6.
7.
8.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch
Network & Internet
.
Touch
Ethernet
.
Place the device into the Ethernet cradle slot.
Slide the switch to the
ON
position.
Touch
Eth0
.
Touch
Disconnect
.
Touch
Eth0
.
109
Accessories
9.
Touch and hold the IP settings drop-down list and select
Static
.
10.
In the
IP
address field, enter the proxy server address.
11.
If required, in the
Gateway
field, enter a gateway address for the device.
12.
If required, in the
Netmask
field, enter the network mask address
13.
If required, in the
DNS address
fields, enter a Domain Name System (DNS) addresses.
14.
Touch
CONNECT
.
15.
Touch .
110
Accessories
5-Slot Charge Only Cradle
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
The 5-Slot Charge Only Cradle:
•
Provides 5 VDC power for operating the device.
•
Simultaneously charges up to five devices and up to four devices and one 4-Slot Battery Charger using the Battery Charger Adapter. See the device Integrator Guide for Android 8.1 Oreo for information on installing the 4-Slot Battery Charger onto the cradle.
•
Consists of a cradle base and cups that can be configured for various charging requirements.
Figure 35
5-Slot Charge Only Cradle
Power LED
Setup
Figure 36
5-Slot Charge Only Cradle
111
Accessories
Charging the Device
1.
Insert the device into a slot to begin charging.
2.
Ensure the device is seated properly.
112
Accessories
Installing the Four Slot Battery Charger
The Battery Charger must be installed in the first slot only.
1.
Remove power from the cradle.
2.
Using a Phillips screwdriver, remove the screw securing the cup to the cradle base.
3.
Slide the cup to the front of the cradle.
113
Figure 37
Remove Cup
Accessories
4.
5.
Carefully lift the cup up to expose the cup power cable.
Disconnect the cup power cable.
NOTE:
Place power cable into adapter to avoid pinching cable.
6.
Connect the Battery Adapter power cable to the connector on the cradle.
114
Accessories
7.
Place adapter onto cradle base and slide toward rear of cradle.
8.
Using a Phillips screwdriver, secure adapter to cradle base with screw.
9.
Align mounting holes on the bottom of the Four Slot Battery Charger with the stubs on the Battery
Adapter.
115
Accessories
10.
Slide the Four Slot battery Charger down toward the front of the cradle.
11.
Connect the output power plug into the power port on the Four Slot Battery Charger.
Removing the 4-Slot Battery Charger
1.
2.
Disconnect the output power plug from the 4-Slot Battery Charger.
At the back of the cup, press down on the release latch.
116
Accessories
3.
4.
Slide the 4-Slot Battery Charger toward the front of the cradle.
Lift the 4-Slot off the cradle cup.
117
Accessories
4-Slot Charge Only Cradle with Battery Charger
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
The 4-Slot Charge Only Cradle with Battery Charger:
•
Provides 5 VDC power for operating the device.
•
Simultaneously charges up to four devices and up to four spare batteries.
Figure 38
4-Slot Charge Only Cradle with Battery Charger
Power LED
118
Accessories
Setup
Figure 39
Connect Battery Charger Output Power Plug
Figure 40
Connect Charge Only Cradle Power
Charging the Device
1.
Insert the device into a slot to begin charging.
119
Accessories
2.
Ensure the device is seated properly.
NOTE:
See
Installing the Four Slot Battery Charger on page 113
for information on installing the 4-Slot
Battery Charger onto the cradle.
Charging Spare Batteries
1.
2.
Connect the charger to a power source.
Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact.
120
Battery
Battery
Charge LED
Battery Slot
Accessories
121
Accessories
5-Slot Ethernet Cradle
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
The 5-Slot Ethernet Cradle:
•
Provides 5.0 VDC power for operating the device.
•
Connects up to five devices to an Ethernet network.
•
Simultaneously charges up to five devices and up to four devices and on 4-Slot Battery Charger using the Battery Charger Adapter.
Figure 41
5-Slot Ethernet Cradle
1000 LED
100/10 LED
122
Accessories
Setup
•
Connect the 5-Slot Ethernet cradle to a power source.
Daisy-chaining Ethernet Cradles
Daisy-chain up to ten 5-Slot Ethernet cradles to connect several cradles to an Ethernet network. Use either a straight or crossover cable. Daisy-chaining should not be attempted when the main Ethernet connection to the first cradle is 10 Mbps as throughput issues will almost certainly result.
To daisy-chain 5-Slot Ethernet cradles:
1.
Connect power to each 5-Slot Ethernet cradle.
2.
Connect an Ethernet cable to the one of the ports on the back of the first cradle and to the Ethernet switch.
123
Accessories
3.
Connect the other end of the Ethernet cable to one of the ports of the back of the second 5-Slot
Ethernet cradle.
To Switch To Power Supply
4.
To Next
Cradle
To Power Supply
Connect additional cradles as described in step 2 and 3.
124
Accessories
Charging the Device
1.
Insert the device into a slot to begin charging.
125
Accessories
2.
Ensure the device is seated properly.
126
Accessories
Installing the Four Slot Battery Charger
NOTE:
The Battery Charger must be installed in the first slot only.
1.
Remove power from the cradle.
2.
Using a Phillips screwdriver, remove the screw securing the cup to the cradle base.
127
Accessories
3.
Slide the cup to the front of the cradle.
4.
5.
Carefully lift the cup up to expose the cup power cable.
Disconnect the cup power cable.
NOTE:
Place power cable into adapter to avoid pinching cable.
6.
Connect the Battery Adapter power cable to the connector on the cradle.
128
Accessories
7.
Place adapter onto cradle base and slide toward rear of cradle.
8.
Using a Phillips screwdriver, secure adapter to cradle base with screw.
129
Accessories
9.
Align mounting holes on the bottom of the Four Slot Battery Charger with the stubs on the Battery
Adapter.
10.
Slide the Four Slot battery Charger down toward the front of the cradle.
11.
Connect the output power plug into the power port on the Four Slot Battery Charger.
Removing the 4-Slot Battery Charger
1.
Disconnect the output power plug from the 4-Slot Battery Charger.
130
Accessories
2.
At the back of the cup, press down on the release latch.
3.
4.
Slide the 4-Slot Battery Charger toward the front of the cradle.
Lift the 4-Slot off the cradle cup.
Ethernet Communication
Ethernet LED Indicators
There are two green LEDs on the side of the cradle. These green LEDs light and blink to indicate the data transfer rate.
Table 16
LED Data Rate Indicators
Data Rate
1 Gbps
100 Mbps
10 Mbps
On/Blink
Off
Off
1000 LED
Off
On/Blink
On/Blink
100/10 LED
Establishing Ethernet Connection
3.
4.
1.
2.
5.
Go to
Settings
.
Touch
Network & internet
>
Ethernet
.
Slide the Ethernet switch to the
ON
position.
Insert the device into a slot.
The icon appears in the Status bar.
Touch
Eth0
to view Ethernet connection details.
Ethernet Settings
The following settings can be configured when using Ethernet communication:
•
Proxy Settings
•
Static IP.
131
Accessories
Configuring Ethernet Proxy Settings
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch
Network & internet
>
Ethernet
.
Place the device into the Ethernet cradle slot.
Slide the switch to the
ON
position.
Touch and hold
Eth0
until the menu appears.
Touch
Modify Proxy
.
Touch the
Proxy
drop-down list and select
Manual
.
In the
Proxy hostname
field, enter the proxy server address.
In the
Proxy port
field, enter the proxy server port number.
NOTE:
When entering proxy addresses in the Bypass proxy for field, do not use spaces or carriage returns between addresses.
10.
In the
Bypass proxy for
text box, enter addresses for web sites that do not require to go through the proxy server. Use the separator “|” between addresses.
11.
Touch
MODIFY
.
12.
Touch .
Configuring Ethernet Static IP Address
The device includes Ethernet cradle drivers. After inserting the device, configure the Ethernet connection:
1.
2.
3.
4.
5.
6.
7.
8.
Swipe down with two fingers from the status bar to open the quick access panel and then touch .
Touch
Network & internet
>
Ethernet
.
Place the device into the Ethernet cradle slot.
Slide the switch to the
ON
position.
Touch
Eth0
.
Touch
Disconnect
.
Touch
Eth0
.
Touch and hold the IP settings drop-down list and select
Static
.
9.
In the
IP
address field, enter the proxy server address.
10.
If required, in the
Gateway
field, enter a gateway address for the device.
11.
If required, in the
Netmask
field, enter the network mask address
12.
If required, in the
DNS address
fields, enter a Domain Name System (DNS) addresses.
13.
Touch
CONNECT
.
14.
Touch .
132
Accessories
4-Slot Battery Charger
CAUTION:
Ensure that you follow the guidelines for battery safety described in
Battery Safety Guidelines on page 176
.
This section describes how to use the 4-Slot Battery Charger to charge up to four device batteries.
Setup
Figure 42
Four Slot Battery Charger Power Setup
Charging Spare Batteries
1.
Connect the charger to a power source.
133
Accessories
2.
Insert the battery into a battery charging well and gently press down on the battery to ensure proper contact.
Battery
Battery
Charge LED
Battery Slot
3.5 mm Audio Adapter
The 3.5 mm Audio Adapter snaps onto the back of the device and removes easily when not in use. When attached to the device the 3.5 mm Audio Adapter allows a user to connect a wired headset to the device.
134
Accessories
Connecting a Headset to the 3.5 mm Audio Adapter
1.
Connect the Quick Disconnect connect of the headset to the Quick Disconnect connector of the 3.5 mm
Quick Disconnect Adapter Cable.
2.
Connect the audio jack of the 3.5 mm Quick Disconnect Adapter Cable to the 3.5 mm Audio Adapter.
Figure 43
Connect Adapter Cable to Audio Adapter
135
Accessories
Attaching the 3.5 mm Audio Adapter
1.
Align the top mounting points on the 3.5 mm Audio Adapter with the mounting slots on the device.
2.
Rotate the Audio Adapter down and press down until it snaps into position.
Device with 3.5 mm Audio Adapter in Holster
When using the device and the audio adapter in a holster, ensure that the display faces in and the headset cable is securely attached to the audio adapter.
Figure 44
Device with 3.5 mm Audio Adapter in Holster
Removing the 3.5 mm Audio Adapter
1.
Disconnect headset plug from 3.5 mm Audio Adapter.
136
Accessories
2.
Lift the bottom of the Audio Adapter away from the device.
3.
Remove Audio Adapter from the device.
Snap-On USB Cable
The Snap-On USB Cable snaps on to the back of the device and removes easily when not in use. When attached to the device the Snap-On USB Cable allows the device to transfer data to a host computer and provide power for charging the device.
Connecting to Device
1.
Align the top mounting points on the cable with the mounting slots on the device.
2.
Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the device.
137
Accessories
USB Communication
1.
Connect the Snap-On USB Cable to the device.
2.
Connect the USB connector of the cable to a host computer.
Charging the Device
1.
2.
Connect the Snap-On USB Cable to the device.
Connect the power supply to the Snap-On USB Cable
3.
Connect to the power supply to an AC outlet.
138
Disconnecting from Device
1.
Press down on the cable.
Accessories
2.
Rotate away from the device. The magnetics release the cable from the device.
Charging Cable Cup
This section describes how to use the Charging Cable Cup to charge the device.
139
Accessories
Charging the Device
1.
Insert the device into the cup of the Charging Cable Cup.
2.
3.
Ensure the device is seated properly.
Slide the two yellow locking tabs up to lock the cable to the device.
140
Accessories
4.
Connect the power supply to the Charging Cable Cup and to a power source.
Snap-On DEX Cable
The Snap-On DEX Cable snaps on to the back of the device and removes easily when not in use. When attached to the device the Snap-On DEX Cable provides electronic data exchange with devices such as vending machines.
Connecting to Device
1.
Align the top mounting points on the cable with the mounting slots on the device.
2.
Rotate the cable down and press until it snaps into place. Magnetics hold the cable to the device.
141
Accessories
DEX Communication
1.
2.
Connect the Snap-On DEX Cable to the device.
Connect the DEX connector of the cable to a device such as a vending machine.
Disconnecting from Device
1.
Press down on the cable.
142
Accessories
2.
Rotate away from the device. The magnetics release the cable from the device.
Trigger Handle
The Trigger Handle adds a gun-style handle with a scanning trigger to the device. It increases comfort when using the device in scan-intensive applications for extended periods of time.
NOTE:
The Attachment Plate with Tether can only be used with Charge Only cradles.
Figure 45
Trigger Handle
Latch
Trigger
Release Button
Attachment Plate with
Tether
Attachment Plate without Tether
Installing the Attachment Plate to Trigger Handle
NOTE:
Attachment Plate with Tether only.
To install the attachment plate to the Trigger Handle:
1.
Insert the loop end of the tether into the slot on the bottom of the handle.
143
Accessories
2.
Feed the attachment plate through the loop.
3.
Pull the attachment plate until the loop tightens on the tether.
Installing the Trigger Handle Plate
3.
4.
1.
2.
5.
6.
Press and hold the
Power
button until the menu appears.
Touch
Power off
.
Touch
OK
.
Press in the two battery latches.
Lift the battery from the device.
Remove the hand strap filler plate from the hand strap slot. Store the hand strap filler plate in a safe place for future replacement.
7.
Insert the attachment plate into the hand strap slot.
8.
Insert the battery, bottom first, into the battery compartment in the back of the device.
144
Accessories
9.
Rotate the top of the battery into the battery compartment.
10.
Press the battery down into the battery compartment until the battery release latches snap into place.
Inserting the Device into the Trigger Handle
1.
Align the back of the Trigger handle with the Trigger Mounting Plate.
2.
Press the two release latches.
145
Accessories
3.
Rotate the device down and press down until it snaps into place.
Removing the Device from the Trigger Handle
1.
Press both Trigger Handle release latches.
146
Accessories
2.
Rotate the device up and remove from the Trigger handle.
147
Accessories
Vehicle Charging Cable Cup
This section describes how to use the Vehicle Charging Cable Cup to charge the device.
148
Accessories
Charging the Device
1.
Insert the device into the cup of the Vehicle Charging Cable.
2.
3.
Ensure the device is seated properly.
Slide the two yellow locking tabs up to lock the cable to the device.
149
Accessories
4.
Insert the Cigarette Lighter plug into the vehicle cigarette lighter socket.
Vehicle Cradle
The cradle:
•
holds the device securely in place
•
provides power for operating the device
•
re-charges the battery in the device.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to
32V and supplies a maximum current of 3A.
150
Figure 46
Vehicle Cradle
Accessories
Device Insertion and Removal
CAUTION:
Ensure that the device is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while driving.
To ensure the device was inserted correctly, listen for the audible click that signifies that the device locking mechanism was enabled and the device was locked into place.
151
Accessories
Figure 47
Install Device into Vehicle Cradle
To remove the device from the cradle, grasp the device and lift out of the cradle.
Figure 48
Remove Device from Vehicle Cradle
152
Accessories
Battery Charging
Ensure the cradle is connected to a power source.
Insert the device into the cradle. The device starts to charge through the cradle as soon as it is inserted.
This does not deplete the vehicle battery significantly. The battery charges in approximately four hours.
See
for charging indications.
NOTE:
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the device will only charge when its temperature is between 0°C to +40°C.
TC7X Vehicle Communication Charging Cradle
The Vehicle Communication Charging Cradle:
•
holds the device securely in place
•
provides power for operating the device
•
re-charges the battery in the device.
The cradle is powered by the USB I/O Hub.
Refer to the TC7X Vehicle Cradle Installation Guide for information on installing the TC7X Vehicle
Communication Charging Cradle.
Figure 49
TC7X Vehicle Communication Charging Cradle
153
Device Insertion and Removal
Figure 50
Insert Device into Cradle
Accessories
1
2
Figure 51
Remove Device from Cradle
1
3
2
2
To ensure the device was inserted correctly, listen for the audible click that signifies that the device locking mechanism was enabled and the device was locked into place.
CAUTION:
Ensure that the device is fully inserted into the cradle. Lack of proper insertion may result in property damage or personal injury. Zebra Technologies Corporation is not responsible for any loss resulting from the use of the products while driving.
To remove the device from the cradle, press the release latch, grasp the device and lift out of the vehicle cradle.
Device Battery Charging
Insert the device into the cradle. The device starts to charge through the cradle as soon as it is inserted.
This does not deplete the vehicle battery significantly. The battery charges in approximately four hours.
See
for all charging indications.
Charging Note
The Vehicle Cradle operating temperature is -40°C to +85°C. When in the cradle, the device will only charge when its temperature is between 0°C to +40°C.
154
Accessories
USB I/O Hub
The USB I/O Hub:
•
provides power to a vehicle cradle
•
provides USB hub for three USB devices (such as printers)
•
provides a powered USB port for charging another device.
The cradle is powered by the vehicle’s 12V or 24V electrical system. The operating voltage range is 9V to
32V and supplies a maximum current of 3A to the vehicle cradle and 1.5 A to the four USB ports simultaneously.
Refer to the device Integrator Guide for Android 8.1 Oreo for information on installing the USB I/O Hub.
Figure 52
USB I/O Hub
Connect USB Cables
The USB I/O Hub provides three USB ports for connecting devices such as printers to a device in the vehicle cradle. To connect USB cables:
1.
Slide the cable cover down and remove.
155
Accessories
2.
3.
Insert the USB cable connector into one of the USB ports.
Place each cable into the cable holder.
4.
Align the cable cover onto the USB I/O Hub. Ensure that the cables are within the cover opening.
5.
Slide cable cover up to lock into place.
External USB Cable
The USB I/O Hub provides a USB port for charging external devices such as cell phones. This port is for charging only.
1.
Open the USB Access Cover.
156
Accessories
2.
Insert the USB cable connector into the USB port.
USB Port
Access Cover
USB Port
Power to Vehicle Cradle
The USB I/O Hub can provide power to a Vehicle Cradle.
1.
Connect the Power Output Cable connector to the Power Input Cable connector of the Vehicle Cradle.
2.
Tighten thumbscrews by hand until tight.
2
Vehicle Cradle Power and
Communication Connector
1
Power and
Communication
Connector
Audio Headset Connection
The USB I/O Hub provides audio connection to the device in a vehicle cradle.
Depending upon the headset, connect the headset and audio adapter to the Headset connector.
157
Accessories
Figure 53
Connect Audio Headset
Headset
Adapter Cable
Collar
Hand Strap Replacement
CAUTION:
Close all running applications prior to replacing the hand strap.
3.
4.
1.
2.
Press and hold the
Power
button until the menu appears.
Touch
Power Off
.
Touch
OK
.
Remove the hand strap clip from the hand strap mounting slot.
158
5.
Press the two battery latches in.
Accessories
6.
Lift the battery from the device.
7.
8.
Remove the battery.
Remove the hand strap plate from the hand strap slot.
159
Accessories
9.
Insert the replacement hand strap plate into the hand strap slot.
10.
Insert the battery, bottom first, into the battery compartment.
11.
Rotate the top of the battery into the battery compartment.
12.
Press the battery down into the battery compartment until the battery release latches snap into place.
160
Accessories
13.
Place hand strap clip into hand strap mounting slot and pull down until it snaps into place.
161
Application Deployment
Security
The device implements a set of security policies that determine whether an application is allowed to run and, if allowed, with what level of trust. To develop an application, you must know the security configuration of the device, and how to sign an application with the appropriate certificate to allow the application to run (and to run with the needed level of trust).
NOTE:
Ensure the date is set correctly before installing certificates or when accessing secure web sites.
Secure Certificates
If the VPN or Wi-Fi networks rely on secure certificates, obtain the certificates and store them in the device’s secure credential storage, before configuring access to the VPN or Wi-Fi networks.
If downloading the certificates from a web site, set a password for the credential storage. The device supports X.509 certificates saved in PKCS#12 key store files with a .p12 extension (if key store has a .pfx or other extension, change to .p12).
The device also installs any accompanying private key or certificate authority certificates contained in the key store.
Installing a Secure Certificate
To install a secure certificate:
1.
Copy the certificate from the host computer to the root of the microSD card or the device’s internal memory. See USB Communication for information about connecting the device to a host computer and copying files.
2.
3.
4.
5.
6.
7.
8.
Go to
Settings
.
Touch
Security
>
Encryption & credentials
.
Touch
Install from storage
.
Navigate to the location of the certificate file.
Touch the filename of the certificate to install.
If prompted, enter the password for credential storage. If a password has not been set for the credential storage, enter a password for it twice and then touch
OK
.
If prompted, enter the certificate’s password and touch
OK
.
162
Application Deployment
9.
Enter a name for the certificate and in the Credential use drop-down, select
VPN and apps
or
Wi-Fi
.
10.
Touch
OK
.
The certificate can now be used when connecting to a secure network. For security, the certificate is deleted from the microSD card or internal memory.
Configuring Credential Storage Settings
1.
2.
Go to
Settings
.
Touch
Security
>
Encryption & credentials
.
• Trusted credentials
- Touch to display the trusted system credentials.
• User credentials
- Touch to display user credentials.
• Install from storage
- Touch to install a secure certificate from the microSD card or internal storage.
• Clear credentials
- Deletes all secure certificates and related credentials.
Development Tools
Android Application Development
Development Workstation
Android development tools are available at developer.android.com
.
To start developing applications for the device, download Android Studio. Development can take place on a Microsoft® Windows®, Mac® OS X®, or Linux® operating system.
Applications are written in the Java language, but compiled and executed in the Dalvik virtual machine.
Once the Java code is compiled cleanly, the developer tools make sure the application is packaged properly, including the AndroidManifest.xml file.
Android Studio contains a full featured IDE as well as SDK components required to develop Android applications.
Enabling Developer Options
The
Developer options
screen sets development related settings. By default, the Developer Options are hidden.
1.
2.
Go to
Settings
.
Touch
About phone
.
3.
4.
5.
6.
7.
Scroll down to
Build number
.
Tap
Build number
seven times. The message
You are now a developer!
appears.
Touch the Back button.
Touch
System
>
Advanced
>
Developer options
.
Slide the
USB debugging
switch to the
ON
position.
163
Application Deployment
EMDK for Android
EMDK for Android provides developers with tools to create business applications for enterprise mobile devices. It is designed for use with Google's Android Studio and includes Android class libraries such as
Barcode, sample applications with source code, and the associated documentation.
EMDK for Android allows applications to take full advantage of the capabilities that Zebra devices have to offer. It embeds Profile Manager technology within Android Studio IDE, providing a GUI-based development tool designed specifically for Zebra devices. This allows fewer lines of code, resulting in reduced development time, effort, and errors.
For more information go to: techdocs.zebra.com
.
StageNow
StageNow is Zebra's next-generation Android Staging Solution built on the MX platform. It allows quick and easy creation of device profiles, and can deploy to devices simply by scanning a bar code, reading a tag, or playing an audio file.
The StageNow Staging Solution includes the following components:
•
The StageNow Workstation tool installs on the staging workstation (host computer) and lets the administrator easily create staging profiles for configuring device components, and perform other staging actions such as checking the condition of a target device to determine suitability for software upgrades or other activities. The StageNow Workstation stores profiles and other created content for later use.
•
The StageNow Client resides on the device and provides a user interface for the staging operator to initiate staging. The operator uses one or more of the desired staging methods (print and scan a bar code, read an NFC tag or play an audio file) to deliver staging material to the device.
For more information go to: techdocs.zebra.com
.
GMS Restricted
GMS Restricted mode deactivates Google Mobile Services (GMS). All GMS apps are removed from the device and communication with Google (analytics data collection and location services) is disabled. It also provides enhanced security and privacy.
Use StageNow to disable or enable GMS Restricted mode. After a device is in GMS Restricted mode, enable and disable individual GMS apps and services using StageNow. To ensure GMS Restricted mode persists after an Enterprise Reset, use the Persist Manager option in StageNow. For more information on
StageNow, refer to techdocs.zebra.com
.
ADB USB Setup
To use the ADB, install the USB driver. This assumes that the development SDK has been installed on the host computer. Go to developer.android.com/sdk/index.html
for details on setting up the development
SDK.
ADB driver for Windows and Linux are available on the Zebra Support Central web site at www.zebra.com/support . Download the ADB and USB Driver Setup package. Follow the instructions with the package to install the ADB and USB drivers for Windows and Linux.
Enabling USB Debugging
By default, USB debugging is disabled.
164
Application Deployment
1.
2.
3.
4.
5.
6.
7.
Go to
Settings
.
Touch
About phone
.
Scroll down to
Build number
.
Tap
Build number
seven times. The message
You are now a developer!
appears.
Touch the Back button.
Touch
System
>
Advanced
>
Developer options
.
Slide the
USB debugging
switch to the
ON
position.
Touch
OK
.
8.
9.
Connect the device to the host computer using the Rugged Charge/USB Cable.
The
Allow USB debugging?
dialog box appears on the device.
10.
On the device, touch
OK
.
11.
On the host computer, navigate to the
platform ‐ tools
folder.
12.
Type
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE:
If device number does not appear, ensure that ADB drivers are installed properly.
13.
Touch the Home button.
Application Installation
After an application is developed, install the application onto the device using one of the following methods:
•
USB connection, see
Installing Applications Using the USB Connection on page 165 .
•
Android Debug Bridge, see
Installing Applications Using the Android Debug Bridge on page 166 .
•
microSD Card, see Installing Applications Using a microSD Card on page 166
.
•
Mobile device management (MDM) platforms that have application provisioning. Refer to the MDM software documentation for details.
Installing Applications Using the USB Connection
CAUTION:
When connecting the device to a host computer and mounting the microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
1.
2.
Connect the device to a host computer using the Rugged Charge/USB cable.
Pull down the Notification panel and touch
Charging this device via USB
.
3.
4.
5.
Touch
File Transfer
.
On the host computer, open a file manager application.
On the host computer, copy the application .apk file from the host computer to the device.
165
Application Deployment
CAUTION:
Carefully follow the host computer’s instructions to unmount the microSD card and disconnect
USB devices correctly to avoid losing information.
6.
Disconnect the device from the host computer.
7.
Swipe the screen up and select to view files on the microSD card or Internal Storage.
8.
9.
Locate the application .apk file.
Touch the application file.
10.
Touch
Continue
to install the app or
Cancel
to stop the installation.
11.
To confirm installation and accept what the application affects, touch
Install
otherwise touch
Cancel
.
12.
Touch
Open
to open the application or
Done
to exit the installation process. The application appears in the App list.
Installing Applications Using the Android Debug Bridge
Use ADB commands to install application onto the device.
CAUTION:
When connecting the device to a host computer and mounting its microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
1.
2.
Ensure that the ADB drivers are installed on the host computer. See
.
Connect the device to a host computer using USB. See USB Communication on page 53 .
3.
4.
5.
6.
7.
8.
Go to
Settings
.
Touch
System
>
Advanced
>
Developer options
.
Slide the switch to the
ON
position.
Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
Touch
OK
.
On the host computer, open a command prompt window and use the adb command:
9.
adb install <application>
where: <application> = the path and filename of the apk file.
Disconnect the device from the host computer. See
.
Installing Applications Using a microSD Card
CAUTION:
When connecting the device to a host computer and mounting its microSD card, follow the host computer’s instructions for connecting and disconnecting USB devices, to avoid damaging or corrupting files.
1.
Copy the apk file to the root of the microSD card.
•
Copy the apk file to a microSD card using a host computer (see USB Communication for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
•
Connect the device with a microSD card already installed to the host computer, and copy apk file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
166
Application Deployment
2.
3.
4.
5.
Connect the device to a host computer using USB. See USB Communication.
Copy the application APK file from the host computer to the microSD card.
Remove the microSD card from the host computer.
Press and hold the Power button on the device until the menu appears.
6.
7.
Touch
Power off
.
Press the two battery latches in.
8.
9.
Lift the battery from the device.
Lift the access door.
10.
Insert the microSD card.
11.
Replace the access door.
12.
Insert the battery, bottom first, into the battery compartment in the back of the device.
13.
Press the battery down until the battery release latches snap into place.
14.
Replace the hand strap, if required.
15.
Press and hold the Power button to turn on the device.
16.
Swipe the screen up and select to view files on the microSD card.
17.
Touch >
SD card
.
18.
Locate the application .apk file.
19.
Touch the application file.
20.
Touch
Continue
. to install the app or
Cancel
to stop the installation.
21.
To confirm installation and accept what the application affects, touch
Install
otherwise touch
Cancel
.
22.
Touch
Open
to open the application or
Done
to exit the installation process. The application appears in the App list.
Uninstalling an Application
5.
6.
7.
3.
4.
1.
2.
Go to
Settings
.
Touch
Apps & notifications
.
Touch
See all apps
to view all apps in the list.
Scroll through the list to the app.
Touch the app. The
App info
screen appears.
Touch
Uninstall
.
Touch
OK
to confirm.
Performing a System Update
System Update packages can contain either partial or complete updates for the operating system. Zebra distributes the System Update packages on the Zebra Support & Downloads web site. Perform a system update using either a microSD card or using ADB.
167
Application Deployment
Downloading the System Update Package
1.
2.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
Download the appropriate System Update package to a host computer.
Performing a System Update Using microSD Card
1.
2.
3.
Copy the System Update zip file to the root of the microSD card.
•
Copy the zip file to a microSD card using a host computer (see USB Communication for more information), and then installing the microSD card into the device (see Replacing the microSD Card for more information).
•
Connect the device with a microSD card already installed to the host computer, and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
Touch
Restart
.
4.
5.
6.
7.
Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from SD card
.
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
or
Diff OTA
Package
.
8.
9.
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to the System Update file.
10.
Press the Power button. The System Update installs and then the device returns to the Recovery screen.
11.
Press the Power button to reboot the device.
Performing a System Update Using ADB
1.
6.
7.
4.
5.
2.
3.
Connect the device to a host computer using the Rugged Charge/USB cable or by inserting the device into the 1-Slot USB/Charge Only Cradle.
Go to
Settings
.
Touch
System
>
Advanced
>
Developer options
.
Slide the switch to the
ON
position.
Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
Touch
OK
.
On the host computer, open a command prompt window and use the adb command:
adb devices
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
168
Application Deployment
NOTE:
If device number does not appear, ensure that ADB drivers are installed properly.
8.
Type:
adb reboot recovery
9.
Press Enter. The System Recovery screen appears on the device.
10.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from ADB
.
11.
Press the Power button.
12.
Use the Volume Up and Volume Down buttons to navigate to
Full OTA Package
or
Diff OTA Package
.
13.
Press the Power button.
14.
On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
15.
Press Enter. The System Update installs (progress appears as percentage in the Command Prompt window) and then the System Recovery screen appears on the device.
16.
Press the Power button to reboot the device.
Verifying System Update Installation
3.
4.
1.
2.
Go to
Settings
.
Touch
About phone
.
Scroll down to
Build number
.
Ensure that the build number matches the new system update package file number.
Enterprise Reset
An Enterprise Reset erases all user data in the
/data
partition, including data in the primary storage locations (
/sdcard
and emulated storage).
Before performing an Enterprise Reset, provision all necessary configuration files and restore after the reset.
Perform Enterprise Reset from the device settings, using a microSD card, or using ADB.
Performing an Enterprise Reset From Device Settings
1.
2.
3.
Go to
Settings
.
Touch
System
>
Reset options
>
Erase all data (enterprise reset)
.
Touch
Erase all data
twice to confirm the Enterprise Reset.
Downloading the Enterprise Reset Package
1.
2.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
Download the Enterprise Reset file to a host computer.
169
Application Deployment
Performing an Enterprise Reset Using microSD Card
1.
2.
3.
Copy the Enterprise Reset zip file to the root of the microSD card.
•
Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
•
Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
Touch
Restart
.
4.
5.
6.
7.
Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from SD card
.
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
8.
9.
Press the Power button.
Press the Volume Up and Volume Down buttons to navigate to the Enterprise Reset file.
10.
Press the Power button. The Enterprise Reset occurs and then the device returns to the Recovery screen.
11.
Press the Power button to reboot the device.
Performing an Enterprise Reset Using ADB
1.
7.
8.
4.
5.
2.
3.
6.
Connect the device to the Rugged Charge/USB cable or insert the device into the 1-Slot USB/Charge
Only Cradle.
Connect the cable or cradle to the host computer.
Go to
Settings
.
Touch
System
>
Advanced
>
Developer options
.
Slide the switch to the
ON
position.
Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
Touch
OK
.
On the host computer, open a command prompt window and type:
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE:
If device number does not appear, ensure that ADB drivers are installed properly.
9.
Type:
adb reboot recovery
170
Application Deployment
10.
Press Enter. The System Recovery screen appears on the device.
11.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from ADB
.
12.
Press the Power button.
13.
Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
14.
Press the Power button.
15.
On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
16.
Press Enter. The Enterprise Reset package installs and then the System Recovery screen appears on the device.
17.
Press the Power button to reboot the device.
Performing a Factory Reset
A Factory Reset erases all data in the
/data
and
/enterprise
partitions in internal storage and clears all device settings. A Factory Reset returns the device to the last installed operating system image. To revert
for more information.
Downloading the Factory Reset Package
To download the Factory Reset package:
1.
Go to the Zebra Support & Downloads web site, www.zebra.com/support .
2.
Download the appropriate Factory Reset file to a host computer.
Performing a Factory Reset Using microSD Card
1.
2.
3.
Copy the Factory Reset zip file to the root of the microSD card.
•
Copy the zip file to a microSD card using a host computer (see USB Communication for more information) and then installing the microSD card into the device (see Replacing the microSD Card for more information).
•
Connect the device with a microSD card already installed to the host computer and copy zip file to the microSD card. See USB Communication for more information. Disconnect the device from the host computer.
Press and hold the Power button until the menu appears.
Touch
Restart
.
4.
5.
6.
7.
Press and hold the PTT button until the device vibrates. The System Recovery screen appears.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from SD card
.
Press the Power button.
Use the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
8.
9.
Press the Power button.
Use the Volume Up and Volume Down buttons to navigate to the Factory Reset file.
10.
Press the Power button. The Factory Reset occurs and then the device returns to the Recovery screen.
171
Application Deployment
11.
Press the Power button to reboot the device.
Performing a Factory Reset Using ADB
To perform an Factory Reset using ADB:
1.
Connect the device to the Rugged Charge/USB cable or insert the device into the 1-Slot USB/Charge
Only Cradle.
2.
3.
4.
5.
6.
Connect the cable or cradle to the host computer.
Go to
Settings
.
Touch
System
>
Advanced
>
Developer options
.
Slide the switch to the
ON
position.
Touch
USB Debugging
. A check appears in the check box. The
Allow USB debugging?
dialog box appears.
7.
8.
Touch
OK
.
On the host computer, open a command prompt window and type:
adb devices
.
The following displays:
List of devices attached
XXXXXXXXXXXXXXX device
(where XXXXXXXXXXXXXXX is the device number).
NOTE:
If device number does not appear, ensure that ADB drivers are installed properly.
9.
Type:
adb reboot recovery
10.
Press Enter. The System Recovery screen appears on the device.
11.
Press the Volume Up and Volume Down buttons to navigate to
Apply upgrade from ADB
.
12.
Press the Power button.
13.
Press the Volume Up and Volume Down buttons to navigate to
Full OTA Package
.
14.
Press the Power button.
15.
On the host computer command prompt window type:
adb sideload <file>
where: <file> = the path and filename of the zip file.
16.
Press Enter. The Factory Reset package installs and then the System Recovery screen appears on the device.
17.
Press the Power button to reboot the device.
Storage
The device contains the following types of file storage:
•
Random Access Memory (RAM)
•
Internal storage
172
Application Deployment
•
External storage (microSD card)
•
Enterprise folder.
Random Access Memory
Executing programs use RAM to store data. Data stored in RAM is lost upon a reset. The operating system manages how applications use RAM. It only allows applications and component processes and services to use RAM when required. It may cache recently used processes in RAM, so they restart more quickly when opened again, but it will erase the cache if it needs the RAM for new activities.
The screen displays the amount of used and free RAM.
• Performance
- Indicates memory performance.
• Total memory
- Indicates the total amount of RAM available.
• Average used (%)
- Indicates the average amount of memory (as a percentage) used during the period of time selected (default - 3 hours).
• Free
- Indicates the total amount of unused RAM.
• Memory used by apps
- Touch to view RAM usage by individual apps.
Viewing Memory
1.
2.
Go to
Settings
.
Touch
System
>
Advanced
>
Developer options
>
Memory
.
Internal Storage
The device has internal storage. The internal storage content can be viewed and files copied to and from when the device is connected to a host computer. Some applications are designed to be stored on the internal storage rather than in internal memory.
Viewing Internal Storage
1.
2.
Go to
Settings
.
Touch
Storage
.
• Internal Storage
- Displays the total amount of space on internal storage and amount used.
If the device has removable storage installed, touch
Internal shared storage
to display a the amount of internal storage used by apps, photos, videos, audio and other files.
External Storage
The device can have a removable microSD card. The microSD card content can be viewed and files copied to and from when the device is connected to a host computer.
Viewing External Storage
1.
2.
Go to
Settings
.
Touch
Storage
.
Portable storage displays the total amount of space on the installed microSD card and the amount used.
To unmount the microSD card, touch .
173
Application Deployment
Touch S
D
card to view the contents of the card.
Formatting a microSD Card
1.
4.
5.
2.
3.
Touch
SD card
.
Touch >
Storage settings
.
Touch
Format
.
Touch
ERASE & FORMAT
.
Touch
DONE
.
Formatting a microSD Card as Internal Memory
4.
5.
2.
3.
You can format a microSD card as internal memory to increase the actual amount of the device’s internal memory. Once formatted, the microSD card can only be read by this device.
1.
Touch
SD card
.
Touch >
Storage settings
.
Touch
Format as internal
.
Touch
ERASE & FORMAT
.
Touch
DONE
.
Enterprise Folder
The Enterprise folder (within internal flash) is a super-persistent storage that is persistent after a reset and an Enterprise Reset. The Enterprise folder is erased during a Factory Reset. The Enterprise folder is used for deployment and device-unique data. The Enterprise folder is approximately 128 MB (formatted).
Applications can persist data after an Enterprise Reset by saving data to the enterprise/user folder. The folder is ext4 formatted and is only accessible from a host computer using ADB or from an MDM.
Managing Apps
Apps use two kinds of memory: storage memory and RAM. Apps use storage memory for themselves and any files, settings, and other data they use. They also use RAM when they are running.
1.
2.
3.
Go to
Settings
.
Touch
Apps & notifications
.
Touch
See all XX apps
to view all apps on the device.
4.
5.
Touch >
Show system
to include system processes in the list.
Touch an app, process, or service in the list to open a screen with details about it and, depending on the item, to change its settings, permissions, notifications and to force stop or uninstall it.
App Details
Apps have different kinds of information and controls.
• Force stop
- Stop an app.
• Disable
- Disable an app.
174
Application Deployment
• Uninstall
- Remove the app and all of its data and settings from the device. See Uninstalling an
Application for information about uninstalling apps.
• Notifications
- Set the app notification settings.
• Permissions
- Lists the areas on the device that the app has access to.
• Storage & cache
- Lists how much information is stored, and includes buttons for clearing it.
• Mobile data & Wi-Fi
- Provides information about data consumed by an app.
• Advanced
•
Screen time - Displays the amount of time the app has displayed on the screen.
• Battery
- Lists the amount of computing power used by the app.
• Open by default
- If you have configured an app to launch certain file types by default, you can clear that setting here.
• Display over other apps
- allows an app to display on top of other apps.
• App details
- Provides a link to additional app details on the Play store.
• Additional settings in the app
- Opens settings in the app.
• Modify system settings
- Allows an app to modify the system settings.
Managing Downloads
Files and apps downloaded using the Browser or Email are stored on the microSD card or Internal storage in the Download directory. Use the Downloads app to view, open, or delete downloaded items.
1.
2.
3.
Swipe the screen up and touch .
Touch >
Downloads
.
Touch and hold an item, select items to delete and touch . The item is deleted from the device.
175
Maintenance and
Troubleshooting
Maintaining the Device
For trouble-free service, observe the following tips when using the device:
•
To avoid scratching the screen, use the supplied stylus or plastic-tipped pens intended for use with a touch-sensitive screen. Never use an actual pen or pencil or other sharp object on the surface of the device screen.
•
The touch-sensitive screen of the device is glass. Do not drop the device or subject it to strong impact.
•
Protect the device from temperature extremes. Do not leave it on the dashboard of a car on a hot day, and keep it away from heat sources.
•
Do not store the device in any location that is dusty, damp, or wet.
•
Use a soft lens cloth to clean the device. If the surface of the device screen becomes soiled, clean it with a soft cloth moistened with an approved cleanser. For a list of approved cleansers, see Approved Cleanser Active
Ingredients.
•
Periodically replace the rechargeable battery to ensure maximum battery life and product performance. Battery life depends on individual usage patterns.
Battery Safety Guidelines
•
The area in which the units are charged should be clear of debris and combustible materials or chemicals.
Particular care should be taken where the device is charged in a non commercial environment.
•
Follow battery usage, storage, and charging guidelines found in this guide.
•
Improper battery use may result in a fire, explosion, or other hazard.
•
To charge the mobile device battery, the ambient battery and charger temperatures must be between +32ºF and +104ºF (0ºC and +40ºC).
•
Do not use incompatible batteries and chargers, including non-Zebra batteries and chargers. Use of an incompatible battery or charger may present a risk of fire, explosion, leakage, or other hazard. If you have any questions about the compatibility of a battery or a charger, contact the Global Customer Support Center.
•
For devices that utilize a USB port as a charging source, the device shall only be connected to products that bear the USB-IF logo or have completed the USB-IF compliance program.
•
Do not disassemble or open, crush, bend or deform, puncture, or shred the battery.
•
Severe impact from dropping any battery-operated device on a hard surface could cause the battery to overheat.
•
Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals.
176
Maintenance and Troubleshooting
•
Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, explosion, or other hazard.
•
Do not leave or store the equipment in or near areas that might get very hot, such as in a parked vehicle or near a radiator or other heat source. Do not place battery into a microwave oven or dryer.
•
Battery usage by children should be supervised.
•
Please follow local regulations to properly dispose of used rechargeable batteries.
•
Do not dispose of batteries in fire.
•
In the event of a battery leak, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with water for 15 minutes, and seek medical advice.
•
If you suspect damage to your equipment or battery, contact Customer Support to arrange for inspection.
Cleaning Instructions
CAUTION:
Always wear eye protection.
Read warning label on alcohol product before using.
If you have to use any other solution for medical reasons please contact the Global Customer Support
Center for more information.
WARNING:
Avoid exposing this product to contact with hot oil or other flammable liquids. If such exposure occurs, unplug the device and clean the product immediately in accordance with these guidelines.
Approved Cleanser Active Ingredients
100% of the active ingredients in any cleaner must consist of one or some combination of the following: isopropyl alcohol, bleach/sodium hypochlorite
1 (see important note below)
, hydrogen peroxide, ammonium chloride, or mild dish soap.
IMPORTANT:
Use pre-moistened wipes and do not allow liquid cleaner to pool.
1
When using sodium hypochlorite (bleach) based products, always follow the manufacturer’s recommended instructions: use gloves during application and remove the residue afterwards with a damp alcohol cloth or a cotton swab to avoid prolonged skin contact while handling the device.
Due to the powerful oxidizing nature of sodium hypochlorite, the metal surfaces on the device are prone to oxidation (corrosion) when exposed to this chemical in the liquid form (including wipes). In the event that these type of disinfectants come in contact with metal on the device, prompt removal with an alcohol-dampened cloth or cotton swab after the cleaning step is critical.
Harmful Ingredients
The following chemicals are known to damage the plastics on the device and should not come in contact with the device: acetone; ketones; ethers; aromatic and chlorinated hydrocarbons; aqueous or alcoholic alkaline solutions; ethanolamine; toluene; trichloroethylene; benzene; carbolic acid and TB-lysoform.
Many vinyl gloves contain phthalate additives, which are often not recommended for medical use and are known to be harmful to the housing of the device.
177
Maintenance and Troubleshooting
Device Cleaning Instructions
Do not apply liquid directly to the device. Dampen a soft cloth or use pre-moistened wipes. Do not wrap the device in the cloth or wipe, instead gently wipe the unit. Be careful not to let liquid pool around the display window or other places. Before use, allow the unit to air dry.
NOTE:
For thorough cleaning, it is recommended to first remove all accessory attachments, such as hand straps or cradle cups, from the mobile device and to clean them separately.
Special Cleaning Notes
The device should not be handled while wearing vinyl gloves containing phthalates, or before hands are washed to remove contaminant residue after gloves are removed.
If products containing any of the harmful ingredients listed above are used prior to handling the device, such as hand sanitizer that contain ethanolamine, hands must be completely dry before handling the device to prevent damage to the device.
IMPORTANT:
If the battery connectors are exposed to cleaning agents, thoroughly wipe off as much of the chemical as possible and clean with an alcohol wipe. It is also recommended to install the battery in the terminal prior to cleaning and disinfecting the device to help minimize buildup on the connectors.
When using cleaning/disinfectant agents on the device, it is important to follow the directions prescribed by the cleaning/disinfectant agent manufacturer.
Cleaning Materials Required
•
Alcohol wipes
•
Lens tissue
•
Cotton-tipped applicators
•
Isopropyl alcohol
•
Can of compressed air with a tube.
Cleaning Frequency
The cleaning frequency is at the customer’s discretion due to the varied environments in which the mobile devices are used and may be cleaned as frequently as required. When dirt is visible, it is recommended to clean the mobile device to avoid build up of particles which make the device more difficult to clean later on.
For consistency and optimum image capture, it is recommended to clean the camera window periodically especially when used in environments prone to dirt or dust.
Cleaning the Device
Housing
Thoroughly wipe the housing, including all buttons and triggers, using an approved alcohol wipe.
178
Maintenance and Troubleshooting
Display
The display can be wiped down with an approved alcohol wipe, but care should be taken not to allow any pooling of liquid around the edges of the display. Immediately dry the display with a soft, non-abrasive cloth to prevent streaking.
Camera and Exit Window
Wipe the camera and exit window periodically with a lens tissue or other material suitable for cleaning optical material such as eyeglasses.
Cleaning Battery Connectors
4.
5.
1.
2.
3.
6.
Remove the main battery from the mobile computer.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
To remove any grease or dirt, rub the cotton portion of the cotton-tipped applicator back-and-forth across the connectors on the battery and terminal sides. Do not leave any cotton residue on the connectors.
Repeat at least three times.
Use a dry cotton-tipped applicator and repeat steps 3 and 4. Do not leave any cotton residue on the connectors.
Inspect the area for any grease or dirt and repeat the cleaning process if necessary.
CAUTION:
After cleaning the battery connectors with bleach-based chemicals, follow the Battery
Connector Cleaning instructions to remove bleach from the connectors.
Cleaning Cradle Connectors
1.
2.
3.
4.
5.
6.
7.
Remove the DC power cable from the cradle.
Dip the cotton portion of the cotton-tipped applicator in isopropyl alcohol.
Rub the cotton portion of the cotton-tipped applicator along the pins of the connector. Slowly move the applicator back-and-forth from one side of the connector to the other. Do not leave any cotton residue on the connector.
All sides of the connector should also be rubbed with the cotton-tipped applicator.
Remove any lint left by the cotton-tipped applicator.
If grease and other dirt can be found on other areas of the cradle, use a lint-free cloth and alcohol to remove.
Allow at least 10 to 30 minutes (depending on ambient temperature and humidity) for the alcohol to air dry before applying power to cradle.
If the temperature is low and humidity is high, longer drying time is required. Warm temperature and low humidity requires less drying time.
CAUTION:
After cleaning the cradle connectors with bleach-based chemicals, follow the Cleaning Cradle
Connectors instructions to remove bleach from the connectors.
179
Maintenance and Troubleshooting
Troubleshooting
Performing a Soft Reset
Perform a soft reset if applications stop working.
1.
Press and hold the Power button until the menu appears.
2.
Touch
Restart
.
The device reboots.
Performing a Hard Reset
CAUTION:
Performing a hard reset with a microSD card installed in the device may cause damage or data corruption to the microSD card. All un-saved data is lost after performing a hard reset.
Perform a hard reset if the device stops responding.
1.
Simultaneously press the Power, Scan and Volume Up buttons for at least four seconds.
2.
When the screen turns off, release the buttons.
The device reboots.
TC72
The following tables provides typical problems that might arise and the solution for correcting the problem.
Table 17
Troubleshooting the TC72
Problem
When pressing the power button the device does not turn on.
When pressing the power button the device does not turn on but two LEDs blink.
Battery did not charge.
Cause
Battery not charged.
Battery not installed properly.
System crash.
Battery charge is at a level where data is maintained but battery should be re-charged.
Cannot see characters on display.
Solution
Charge or replace the battery in the device.
Install the battery properly.
Perform a reset.
Charge or replace the battery in the device.
Battery failed.
Device removed from cradle while battery was charging.
Extreme battery temperature.
Replace battery. If the device still does not operate, perform a reset.
Insert device in cradle. The 4,620 mAh battery fully charges in less than five hours at room temperature.
Battery does not charge if ambient temperature is below 0°C (32°F) or above 40°C (104°F).
Device not powered on. Press the
Power
button.
180
Maintenance and Troubleshooting
Table 17
Troubleshooting the TC72
Problem
During data communication with a host computer, no data transmitted, or transmitted data was incomplete.
Cause
Device removed from cradle or disconnected from host computer during communication.
Incorrect cable configuration.
Communication software was incorrectly installed or configured.
Wi-Fi radio is not on.
You moved out of range of an access point.
During data communication over
Wi-Fi, no data transmitted, or transmitted data was incomplete.
During data communication over
WAN, no data transmitted, or transmitted data was incomplete.
During data communication over
Bluetooth, no data transmitted, or transmitted data was incomplete.
No sound.
Device shuts off.
You are in an area of poor cellular service.
APN is not set up correctly.
SIM card not installed properly.
Volume setting is low or turned off.
Device is inactive.
Adjust the volume.
Solution
Replace the device in the cradle, or reattach the communication cable and re-transmit.
See the system administrator.
Perform setup.
Turn on the Wi-Fi radio.
Move closer to an access point.
Move into an area that has better service.
See system administrator for APN setup information.
Remove and re-install the SIM card.
Data plan not activated. Contact your service provider and ensure that your data plan is enable.
Bluetooth radio is not on.
Turn on the Bluetooth radio.
You moved out of range of another Bluetooth device.
Move within 10 meters (32.8 feet) of the other device.
The display turns off after a period of inactivity. Set this period to 15 seconds, 30 seconds, 1, 2, 5, 10 or
30 minutes.
Replace the battery.
Reset the device.
Tapping the window buttons or icons does not activate the corresponding feature.
Battery is depleted.
The device is not responding.
181
Maintenance and Troubleshooting
Table 17
Troubleshooting the TC72
Problem
A message appears stating that the device memory is full.
The device does not decode with reading bar code.
Device cannot find any Bluetooth devices nearby.
Cannot unlock device.
Cause
Too many files stored on the device.
Too many applications installed on the device.
Scanning application is not loaded.
Unreadable bar code.
Distance between exit window and bar code is incorrect.
Device is not programmed for the bar code.
Device is not programmed to generate a beep.
Battery is low.
Solution
Delete unused memos and records. If necessary, save these records on the host computer (or use an
SD card for additional memory).
Remove user-installed applications on the device to recover memory. Select >
Storage
>
FREE UP
SPACE
>
REVIEW RECENT ITEMS
. Select the unused program(s) and tap
FREE UP
.
Load a scanning application on the device or enable
DataWedge. See the system administrator.
Ensure the symbol is not defaced.
Place the device within proper scanning range.
Program the device to accept the type of bar code being scanned. Refer to the EMDK or DataWedge application.
If the device does not beep on a good decode, set the application to generate a beep on good decode.
Too far from other
Bluetooth devices.
The Bluetooth device(s) nearby are not turned on.
The Bluetooth device(s) are not in discoverable mode.
User enters incorrect password.
If the scanner stops emitting a laser beam upon a trigger press, check the battery level. When the battery is low, the scanner shuts off before the device low battery condition notification. Note: If the scanner is still not reading symbols, contact the distributor or the Global Customer Support Center.
Move closer to the other Bluetooth device(s), within a range of 10 meters (32.8 feet).
Turn on the Bluetooth device(s) to find.
Set the Bluetooth device(s) to discoverable mode. If needed, refer to the device’s user documentation for help.
If the user enters an incorrect password eight times, the user is requested to enter a code before trying again.
If the user forgot the password, contact system administrator.
182
Maintenance and Troubleshooting
2-Slot Charge Only Cradle
Table 18
Troubleshooting the 2-Slot Charge only Cradle
Symptom
LEDs do not light when device or spare battery is inserted.
Device battery is not charging.
Spare battery is not charging.
Possible Cause
Cradle is not receiving power.
Device is not seated firmly in the cradle.
Spare battery is not seated firmly in the cradle.
Device was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
The device is not fully seated in the cradle.
Extreme battery temperature.
Battery not fully seated in charging slot.
Battery inserted incorrectly.
Battery is faulty.
Action
Ensure the power cable is connected securely to both the cradle and to AC power.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Remove and re-insert the spare battery into the charging slot, ensuring it is firmly seated.
Ensure cradle is receiving power. Ensure device is seated correctly. Confirm main battery is charging.
The 4,620 mAh battery fully charges in less than five hours.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 0 °C (32 °F) or above 40 °C (104 °F).
Remove and re-insert the spare battery in the cradle, ensuring it is firmly seated. The 4,620 mAh battery fully charges in less than five hours.
Re-insert the battery so the charging contacts on the battery align with the contacts on the cradle.
Verify that other batteries charge properly. If so, replace the faulty battery.
2-Slot USB/Ethernet Cradle
Table 19
Troubleshooting the 2-Slot USB/Ethernet Cradle
Symptom
During communication, no data transmits, or transmitted data was incomplete.
Possible Cause
Device removed from cradle during communications.
Incorrect cable configuration.
Device has no active connection.
USB/Ethernet module switch in not in the correct position.
Action
Replace device in cradle and retransmit.
Ensure that the correct cable configuration.
An icon is visible in the status bar if a connection is currently active.
For Ethernet communication, slide the switch to the
position. For USB communication, slide the switch to the position.
183
Maintenance and Troubleshooting
Table 19
Troubleshooting the 2-Slot USB/Ethernet Cradle (Continued)
Symptom
LEDs do not light when device or spare battery is inserted.
Device battery is not charging.
Spare battery is not charging.
Possible Cause
Cradle is not receiving power.
Device is not seated firmly in the cradle.
Spare battery is not seated firmly in the cradle.
Device was removed from cradle or cradle was unplugged from AC power too soon.
Battery is faulty.
The device is not fully seated in the cradle.
Extreme battery temperature.
Battery not fully seated in charging slot.
Battery inserted incorrectly.
Battery is faulty.
Action
Ensure the power cable is connected securely to both the cradle and to AC power.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Remove and re-insert the spare battery into the charging slot, ensuring it is firmly seated.
Ensure cradle is receiving power. Ensure device is seated correctly. Confirm main battery is charging.
The 4,620 mAh battery fully charges in less than five hours.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove and re-insert the device into the cradle, ensuring it is firmly seated.
Battery does not charge if ambient temperature is below 0 °C (32 °F) or above 40 °C (104 °F).
Remove and re-insert the spare battery in the cradle, ensuring it is firmly seated. The 4,620 mAh battery fully charges in less than five hours.
Re-insert the battery so the charging contacts on the battery align with the contacts on the cradle.
Verify that other batteries charge properly. If so, replace the faulty battery.
5-Slot Charge Only Cradle
Table 20
Troubleshooting the 5-Slot Charge Only Cradle
Problem
Battery is not charging.
Cause
Device removed from the cradle too soon.
Battery is faulty.
Device is not inserted correctly in the cradle.
Ambient temperature of the cradle is too warm.
Solution
Replace the device in the cradle. The battery fully charges in approximately five hours.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove the device and reinsert it correctly. Verify charging is active. Touch >
System
>
About phone
>
Battery
Information
to view battery status.
Move the cradle to an area where the ambient temperature is between -10 °C (+14 °F) and +60 °C (+140 °F).
184
Maintenance and Troubleshooting
5-Slot Ethernet Cradle
Table 21
Troubleshooting the 5-Slot Ethernet Cradle
Problem
During communication, no data transmits, or transmitted data was incomplete.
Battery is not charging.
Device removed from cradle during communication s.
Cause
Incorrect cable configuration.
Device has no active connection.
Device removed from the cradle too soon.
Battery is faulty.
Device is not inserted correctly in the cradle.
Ambient temperature of the cradle is too warm.
Solution
Replace device in cradle and retransmit.
Ensure that the correct cable configuration.
An icon is visible in the status bar if a connection is currently active.
Replace the device in the cradle. The battery fully charges in approximately five hours.
Verify that other batteries charge properly. If so, replace the faulty battery.
Remove the device and reinsert it correctly. Verify charging is active. Touch >
System
>
About phone
>
Battery
Information
to view battery status.
Move the cradle to an area where the ambient temperature is between -10 °C (+14 °F) and +60 °C (+140 °F).
4-Slot Battery Charger
Table 22
Troubleshooting the 4-Slot Battery Charger
Problem
Spare Battery
Charging LED does not light when spare battery is inserted.
Cause
Spare battery is not correctly seated.
Solution
Remove and re-insert the spare battery into the charging slot, ensuring it is correctly seated.
185
Maintenance and Troubleshooting
Table 22
Troubleshooting the 4-Slot Battery Charger (Continued)
Problem
Spare Battery not charging.
Cause
Charger is not receiving power.
Spare battery is not correctly seated.
Battery adapter is not seated properly.
Battery was removed from the charger or charger was unplugged from AC power too soon.
Battery is faulty.
Ensure charger is receiving power. Ensure the spare battery is seated correctly. If a battery is fully depleted, it can take up to five hours to fully recharge a Standard Battery and it can take up to eight hours to fully recharge an Extended Life
Battery.
Verify that other batteries charge properly. If so, replace the faulty battery.
Solution
Ensure the power cable is connected securely to both the charger and to AC power.
Remove and re-insert the battery into the battery adapter, ensuring it is correctly seated.
Remove and re-insert the battery adapter into the charger, ensuring it is correctly seated.
186
Technical Specifications
For device technical specifications, go to www.zebra.com/support .
Data Capture Supported Symbologies
Item
1D Bar Codes
2D Bar Codes
Description
Code 128, EAN-8, EAN-13, GS1 DataBar Expanded, GS1 128, GS1 DataBar
Coupon, UPCA, Interleaved 2 of 5, UPC Coupon Code
PDF-417, QR Code, Digimarc, Dotcode
SE4750-SR Decode Distances
The table below lists the typical distances for selected bar code densities. The minimum element width (or
“symbol density”) is the width in mils of the narrowest element (bar or space) in the symbol.
Symbol Density/ Bar Code
Type
3 mil Code 39
5.0 mil Code 128
5 mil PDF417
6.67 mil PDF417
10 mil Data Matrix
100% UPCA
4.1 in.
10.41 cm
3.5 in.
8.89 cm
4.4 in.
11.18 cm
3.2 in.
8.13 cm
3.3 in.
8.38 cm
2.0 in.
5.08 cm
Near
Typical Working Ranges
4.9 in.
12.45 cm
6.8 in.
17.27 cm
6.3 in.
16.00 cm
8.1 in.
20.57 cm
8.5 in.
21.59 cm
18.0 in.
45.72 cm
Far
187
Technical Specifications
Symbol Density/ Bar Code
Type
Near
Typical Working Ranges
Far
15 mil Code 128
20 mil Code 39
2.6 in.
6.06 cm
1.8 in.
4.57 cm
19.8 in.
50.29 cm
27.0 in.
68.58 cm
Note: Photographic quality bar code at 18° tilt pitch angle under 30 fcd ambient illumination.
I/O Connector Pin-Outs
Pin 1
7
8
5
6
3
4
1
2
9
10
Pin Signal
GND
RXD_MIC
PWR_IN_CON
TRIG_PTT
GND
USB-OTG_ID
TXD_EAR
USB_OTG_VBUS
USB_OTG_DP
USB_OTG_DM
Description
Power/signal ground.
UART RXD + Headset microphone.
External 5.4 VDC power input.
Trigger or PTT input.
Power/signal ground.
USB OTG ID pin.
UART TXD, Headset ear.
USB VBUS
USB DP
USB DM
2-Slot Charge Only Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Description
Height: 10.6 cm (4.17 in.)
Width: 19.56 cm (7.70 in.)
Depth: 13.25 cm (5.22 in.)
748 g (26.4 oz.)
12 VDC
30 watts
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
188
Technical Specifications
Item
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10 kV contact
+/- 10 kV indirect discharge
2-Slot USB/Ethernet Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 20 cm (7.87 in.)
Width: 19.56 cm (7.70 in.)
Depth: 13.25 cm (5.22 in.)
870 g (30.7 oz.)
12 VDC
30 watts
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
5-Slot Charge Only Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Description
Height: 90.1 mm (3.5 in.)
Width: 449.6 mm (17.7 in.)
Depth: 120.3 mm (4.7 in.)
1.31 kg (2.89 lbs.)
12 VDC
65 watts
90 watts with 4–Slot Battery Charger installed.
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
189
Technical Specifications
Item
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
0% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
5-Slot Ethernet Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 21.7 cm (8.54 in.)
Width: 48.9 cm (19.25 in.)
Depth: 13.2 cm (5.20 in.)
2.25 kg (4.96 lbs)
12 VDC
65 watts
90 watts with 4-Slot Battery Charger installed.
0 °C to 50 °C (32 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
4-Slot Battery Charger Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Description
Height: 4.32 cm (1.7 in.)
Width: 20.96 cm (8.5 in.)
Depth: 15.24 cm (6.0 in.)
386 g (13.6 oz.)
12 VDC
40 watts
0 °C to 40 °C (32 °F to 104 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
0 °C to 40 °C (32 °F to 104 °F)
190
Technical Specifications
Item
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
+/- 10kV indirect discharge
Charge Only Vehicle Cradle Technical Specifications
Dimensions
Item
Weight
Input Voltage
Power Consumption
Operating Temperature
Storage Temperature
Charging Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 12.3 cm (4.84 in.)
Width: 11.0 cm (4.33 in.)
Depth: 8.85 cm (3.48 in.)
320 g (11.3 oz.)
12/24 VDC
40 watts
-40 °C to 85 °C (-40 °F to 185 °F)
-40 °C to 85 °C (-40 °F to 185 °F)
0 °C to 40 °C (32 °F to 104 °F)
5% to 95% non-condensing
76.2 cm (30.0 in.) drops to vinyl tiled concrete at room temperature.
+/- 20kV air
+/- 10kV contact
Trigger Handle Technical Specifications
Dimensions
Item
Weight
Operating Temperature
Storage Temperature
Humidity
Drop
Electrostatic Discharge
(ESD)
Description
Height: 11.2 cm (4.41 in.)
Width: 6.03 cm (2.37 in.)
Depth: 13.4 cm (5.28 in.)
110 g (3.8 oz.)
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
1.8 m (6 feet) drops to concrete over temperature range.
+/- 20kV air
+/- 10kV contact
191
Technical Specifications
Charging Cable Cup Technical Specifications
Item
Length
Input Voltage
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
Description
25.4 cm (10.0 in.)
5.4 VDC
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
Snap-On USB Cable Technical Specifications
Item
Length
Input Voltage
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
Description
1.5 cm (60.0 in.)
5.4 VDC (external power supply)
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
DEX Cable Technical Specifications
Item
Length
Operating Temperature
Storage Temperature
Humidity
Electrostatic Discharge
(ESD)
Description
1.5 cm (60.0 in.)
-20 °C to 50 °C (-4 °F to 122 °F)
-40 °C to 70 °C (-40 °F to 158 °F)
10% to 95% non-condensing
+/- 20kV air
+/- 10kV contact
192
Index
A
approved cleanser 177 approved cleanser active ingredients 177
apps
RxLogger Utility 83 sound recorder 83
B barcode scanning
battery
low battery notification 52 monitor usage 52
battery management 51 battery level 51 battery present status 51 battery optimization 51
C
front camera photo settings 74
front camera video settings 76
photo settings 73 rear camera photo settings 73
recording videos 72 taking panoramic photos 72
video settings 75 camera settings 73, 75
battery connectors 179 camera and exit window 179 cradle connectors 179 display 179
materials 178 cleaning instructions 178
cradle
193
D data capture
datawedge 43 decoders 43 disabling 43 enable 43
digital camera 32 barcode scanning 32 data capture 32
DS3678
pairing 42 pairing using Bluetooth HID 42
DS3678 digital scanner
barcode scanning 33 data capture 33
E
F
G
H
I integrated imager
barcode scanning 31 data capture 31 operational modes 31
interactive sensor technology 52
K
editing text 61 numeric tab 61
L
M maintenance
approved cleanser active ingredients 177
Index
194
clean housing 178 cleaning frequency 178
cleaning materials required 178 device cleaning instructions 178
N
notifications
O
operational modes
decode mode 31 pick list mode 31
P pairing
RS507/RS6000 hands-free imager 39
using Bluetooth HID (RS507/RS6000) 41
using Bluetooth HID(DS3678) 42
using simple serial interface(RS507/RS6000) 40
Pairing Using Bluetooth Human Interface Device 41
photos
PTT Express
private response 80 talk groups 80
PTT-Express
Q
quick settings
R
reset device
RS507
RS507/RS6000
pairing using Bluetooth HID 41
pairing using simple serial interface 40
RS6000
S scanning
setting
Index
sharing information using NFC 96
T
transferring files using USB 53
U
V
videos
W
wireless local area network 85
195
www.zebra.com
Stáhnout
Veřejný odkaz aktualizován
Veřejný odkaz na váš chat byl aktualizován. You may view and manage your chat links after registration here.
Veřejný odkaz na dokument
Reklama
