Honda WP20X Owner Manual

HONDA
WP20X-WP30X
OWNER'S MANUAL
32ŸE5612 © Honda Motor Co., Ltd. 2002
00X32-YE5-6120 ® © GP) 1000.2002.08
—l1—
Thank you for purchasing a Honda water pump,
This manual covers operation and maintenance of the WP20X and WP30X water pump
All information in this publication is based on the latest product information availabl
at the time of approval for printing.
Honda Motor Co,, Lid. reserves the right to make changes at any time without notic
and without incurring any obligation.
No part of this publication may De reproduced without written permission.
This manual should be considered a permanent part of the pump and should remai
with the pumg if it is resold,
Illustrations herein ara mainly based on WP30X model.
Pay special attention to statements preceded by the following words:
Indicate a strong possibility of severe personal injury or death if instn
tion are not followed.
CAUTION: Indicates a possibility of personal injury or equipment damage if instruction
are not followed.
NOTE: Gives helpful information.
If a problem should arise, or if you have any questions about the pump, consult an auth
rized Honda dealer.
iio A This Honda water pump is designed to give safe and dependable service
operated according to instructions. Read and understand the Owner's Manual before a
erating the pump. Failure to do so could result in personal injury or equipment damag
« The lllustratlon may vary according to the type.
SAFETY INSTRUCTIONS
FAT TEN
To ensure safe operation-
- Honda water pump is designed to give safe and
dependable service if operated according to
Instructions.
Read and understand tha Owner's Manual before
operating the water pump. Failure to do so could result
in personal injury or equipment damage,
» The muffler becomes very hat during operation and |
remains hot for a while after stopping the engine,
Be careful not to touch the muffler while it is hot.
Lot the engine cool before storing the water pump
indoors. |
The engine exhaust system will be heated during
operation and remain hot immediately after stopping
the engine. |
To prevent scalding, pay attention to the warning
marks attached to the water pump.
pt’
Always make a pre-operation inspection (page 3} before you start the engine, You
may prevent an accident or equipment damage.
For safety, never pump flammable or corrosive liquids such as gasoline or acid. Also
to avoid pump corrosion, never pump sea water, chemical solutions, or caustic liquids
such as used oil, wine, or milk.
Place the pump on a firm, level surface, If the pump is titled or overturned, fuel
spillage may result.
To prevent fire hazards and to provide adequate ventilation, keep the pump at least
1 meter (3 feet) away from building walls snd other equipment during operation.
Do not place {flammable objects close to the pump.
Children and pets must be kept away from the area of operation due to a possibility
of burns from the hot engine components.
Know how ta stop the pump quickly, and understand the operation of all controls.
Never permit anyone to operate the pump without proper instructions.
Gasoline is extremely flammable and is explosive under certain conditions.
— Refuel in a well-ventilated area with the engine stopped. Do not smoke or allow
flames or sparks in the refueling area or where gasoline is stored.
— Do not overfill the tank. After refueling, make sure the tank cap is closed properly
and securely. 3
A WARNING
To ensure safe operation-
se Be careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite.
M any fuel is spilled, mada sure the area is dry before starting the engine.
Never run the engina in an enclosed or confined area. Exhaust contains poisonous
carbon monoxide gas: exposure can cause loss of consciousness and may lead to
death.
The muffler becomes very hot during operation and remains hot for a while after
stopping the engine. Be careful not to touch the mufflar while it is hot. Let the
engine cool before storing the pump indoors. Children and pets must be kept away
from tha area of operation due to 8 potsibility of burns from hot engine components.
2. SAFETY LABEL LOCATIONS
CE mark and noise label locations
[DXE typa only] [DXE type only]
Thasa labels warn you of potential hazards that can cause serious injury. Read the
labels and safety notes and precautions described in this manual carefully. .
CE MARK
If a label comes off or becomes hard to read, contact your Honda dealer for a r
replacement.
Manufacturar and address
2-1-1 MINAMI AGYAMA
HOT CAUTION TOKYO, JAPAN
READ OWNER'S MANUAL
Ao
HONDA MOTOR CO., LTD
C € EWP20X BE 200
E 2.9 kW 3600 min: 0 24.5kg <
MINATO KU
Machina wealgh
[stondard specilicatiand
[Example: WP20X CE MARK)
[Exemple: WP20X NOISE LABEL]
и
3. COMPONENT IDENTIFICATION
:WP20X >
1)
2}
3}
4}
19)
16)
[7)
(8)
MUFFLER
FUEL TANK CAP
DISCHARGE PORT
FRAME
OIL FILER CAP/DIPSTICK
ENGINE SWITCH
STARTER GRIP
FUEL VALVE
{9) CHOKE LEVER
(10) THROTTLE LEVER
(11} PRIMING WATER FILLER
CAP
(12) AIR CLEANER
{13) STRAINER
(14) OIL DRAIN PLUG
(15) PUMP DRAIN PLUG
(16) SUCTION PORT
< WP30X >
(1)
(2)
(3)
14)
(5)
(6)
{7}
(8)
MUFFLER
FUEL TANK CAP
DISCHARGE PORT
FRAME
OIL FILER CAP/DIPSTICK
ENGINE SWITCH
STARTER GRIP
FUEL VALVE
{99 CHOKE LEVER
(10) THROTTLE LEVER
(11) PRIMING WATER FILLER
CAP
(12} AIR CLEANER
{13} STRAINER
(14) OIL DRAIN PLUG
(15) PUMP DRAIN PLUG
{16} SUCTION PORT
—B—
4. PRE-OPERATION FOR STARTING
1. Connect the suction hose,
Use commercially available hose, hase connector, and hose bands. The suction hose must
be of reinforced, noncollapsible construction. Suction hose length should not be longer
then necessary, as pump performance is best when the pump is not far above the water
level. Self-priming time is also proportional to hose length.
The strainer that is provided with the pump should be attached to the end of the suction
hose with a band, as shown.
CAUTION: Always install the strainer on the end of the suction hose before pumping.
The strainer will excluse debris that can cause clogging or impeller damage.
MOTE: Tighten the hose connector and bands to prevent air leakage and loss of suction.
A loosely connected suction hose will reduce pump performance and self-priming ability.
{1} SUCTION HOSE
(2) HOSE BAND
(3) STRAINER
2. Connect the discharga hose.
Use a commercially available hose, hose connector, and hose band. A short, large-dia-
meler hose is most efficient. Long or small-diameter hose increases fluid friction and
reduces pump output.
NOTE: Tighten the hose band securely to prevent the hose from disconnecting under
high pressure.
(1) DISCHARGE HOSE
(2) HOSE BAND
3. Check the engine cil lavel.
CAUTION:
» Engine oil is a major factor affecting engine performance and service life. Non-deter
gent or vegetable cily are not reseommendad.
« Be sure to check the engina on a level surface with the engine stopped.
Use Honda 4-stroke oil, ar an equivalent SAE Viscosity Grades
high detergent premium quatity motor oil 15W-40
certified tomeet or exceed U.S. auto- CC A
mobile manufacturer's requirements lor 10W-40
Service Classification SG-SF. {motor oils 1 1 |
clessified SG -SF will show this dasignation LEE
on the container.) em
Select the appropriate viscosity for the
average temperature in your area, 730 720 —10 0 10 £ “0 40°C
—-20 0 20 40 & 60 100°F
AMBIENT TEMPERATURE
Remove the ail filler cap, and wipe tha dipstick with a clean rag. Check tha oil
lavel by inserting the dipstick in the filler hole without screwing it in,
If the oil level is below the end of the dipstick, refill with recommended oil up
to the top of the oil filler nack,
[1) OIL FILLER NECK
{21 OIL FILLER CAP
(3} UPPER LEVEL
4. Check the fuel level.
Remove the fuel cap and the check the fuel level. Refill the tank it the fuel level
is low,
Use automotive gasoline {Unleaded or lowleaded is preferred to minimize combustion
chamber deposits),
FOR NEW SOUTH WALES ONLY
Use unleaded fuel only.
Never use an oil/gasoline mixture ar dirty gasoline. Avoid getting dirt, dust or water
in the fuel tank.
FOR: E Te
e Gasolina is extramaly flammable and is explosive under certain conditions,
® Refuel in a well-ventilated area with the engina stopped. Do not smoke or allow
flames or sparks in the area where the engine is refueled or where gasoline is stored.
® Do not overfill the fuel tank (there should be no fuel in the filler neck). After
refueling, make sure the tank cap is closed properly and securely,
® Ве careful not to spill fuel when refueling. Spilled fuel or fuel vapor may ignite,
If any fuel is spilled, make sure the area is dry before starting the engine,
® Avoid repaated or prolongad contact with skin or breathing of vapor. KEEP OUT
OF REACH OF CHILDREN.
Fuel tank capacity: WP20X ...
WP30X ...
2.5 ¢ {0.66 US gal, 0.55% Imp gal)
3.6 £ (0.95 US gal, 0.73 Imp gal)
Gasolines containing alcohol
If you decida to use a gasoline containing alcohol (gasohol), be sure it's octane rating is at
least as high as that recommended by Honda, There are two types of “gasoho!”: one
containing ethanol, and the other containing methanol, Do not use gaschol that contains
more than 10% elhanol, Do not use gasoline containing methanol {methyl or wood
alcohol) that does not also contain cosolvents and corrosion inhibitors Tor methanol.
Never use gasoline contaming more than 5% methanol, even if it has cosolvents and corro:
sion inhibitors,
NOTE:
Fuel system damage or engine performance problems resulting from the use of fuels
that contain alcohal is not covered under the warranty. Honda cannot endorse the use
af fuels containing methanol since evidence of their suitability is as yet incomplete.
Before buying fuel from an unfamiliar station, try to find out it the fuel contains
alcohol, if it does, confirm the type and percantage of alcohol used. If vou notice any
undersirable operating symptoms while using a gascline that contains alcohol, or one
that you think contains alcohol, switch to a gasoline that you know does not contain
alcohol.
5. Check tha air cleaner element.
Remove the wing nut, washer and air cleaner cover,
Check the element for dirt or obstruction. |
Clean the element if necessary (ses page 221. =
“>,
(1) AIR CLEANER COVER SI
(7) AIR CLEANER ELEMENT
J
E
CAUTION: Never run the engine without the air cleaner. Rapid engine wear will result
from contaminants, such as dust and dirt, being drawn through the carburetor, into
the engine,
6, Check the priming water. 5. STARTING THE ENGINE
The pump chamber should be primed with full of water before operating. 1. Turn the fuel valve ON.
2. Close the choke lever,
CAUTION: Never attempt to oparata the pump without priming water or the pump will 200 h bi ure is hiah
overheat. Extended dry operation will destroy the pump seal. If tha unit has been oper. NOTE: Do nat use the choke if the engine 15 warm or the ambient temperature is hig
ted dry, stop th ine i ediatel d allow th mp to cool before adding primin
ater] dry stop the engine immediately and aliow the pump ap 8 1) FUEL VALVE
{2} CHOKE LEVER
{1} PRIMING WATER FILLER PLUG
3. Turn the engine switch to the ON position,
(1) ENGINE SWITCH
4. Mave the throttle lever slightly to the left.
(1) THROTTLE LEVER
3. Pull the starter grip lightly until resistance is felt, then pull it briskly.
CAUTION: Do not allow the starter grip to snap back against the engine. Return it
gently to prevent damage to the starter.
1) STARTER GRIP
e High altitude operation
At high altitude, the standard carburetor air-fuel mixture will be excessively
rich, Performance will decrease, and fuel consumption will increase.
High altitude performance can be improved by specifications to the carburetor.
If you always operate the generator at altitude higher than 1.500 m (5,000 feet)
above sea level, have your authorized Honda dealer perform these carburetor
modifications.
Even with suitable carburetor jetting, engine horsepower will decrease
approximately 3.5 % for each 300 m {1,000 foot) increase in altitude. The effect
of altitude on horsepowar will be greater than this if no carburetor
modification is made.
CAUTION: Operation of the pump at an altitude lower than the carburetor is
jetted for may result in reduced performance, overheating, and serious engine
damage caused by an excessivaly lean air-fuel mixture.
6. OPERATION
1. As the engine warms up, gradually open the choke,
(1) CHOKE LEVER
2. Set the throttle at the desired speed.
(1) THROTTLE LEVER
7. STOPPING THE ENGINE
1. Move the throttle lever fully to the right.
2. Turn the engine switch to the OFF position,
(1) THROTTLE LEVER
(2) ENGINE SWITCH
LOW
ÔFF
3. Turn the fuel valve OFF.
(1} FUEL VALVE
NOTE: To stop the engine in an emergency, turn the engine switch to the OFF position,
3. MAINTENANCE
"eriodic inspection and adjustment of the pump are essential if high level performance 15
0 be meintained, Regular maintenance will also help to extend service life. The required
ervice intervals and the kind of maintenance to be performed are described in the next
rage.
Shut off the engine before parforming any maintenance. If the engine
must be run, make sure the area is well ventilated. The exhaust contains poisonous
:arbon monoxide gas; exposure cen cause loss of conciousness and may lead to death.
-AUTION:
» If the pump has baen used with sea water, muddy water, etc., pump clean, fresh water
immediately afterward to reduce corrosion or remove sadimant.
» Use genuine Honda parts or their equivalent for maintanance or repair.
Replacemant parts which are not of equivalent quality may damage the pump.
Maintenanca Schedule
REGULAR SERVICE PERIOD 15) First Every Every Every
Item Parform at every indicated Each month |3 months| 6 months, year
month or oparating hour use or or or or
intarval, whichovar comas first, 20 hrs. | 50 hrs. | 100 hrs, | 300 hrs.
Engine oil Check level o
Chango o o
Air filter Check О
Clean On}
Sediment cup Clean ©
Spark plug Chackadjust o
Replace C
Spark arrostor Clean o
{optional pens)
Idle speed Check-adjust 012)
Yalva ciearanca Chack-adjust 0 (2)
Combustion chamber Claan After every 500 hrs. (2)
Fuel tank and filter Cloan | | © [2] |
Fuel tube Check Every 2 yaars [Roplace if nocossary}{2)
Impeller Check 012)
Impellar cloarance Check 012)
Pump inle1 valve Cheek 012)
NOTE (1)
(2)
(3)
Service more frequently when used in dusty areas.
These items should be serviced by your servicing dealer, unless
you have the proper tools and are mechanically proficient. Refer
to the Honda shop manual for service procedures.
For commercial use, log hours of operation to determine proper
maintenance intervals.
lo AAI Un
Drain the oil while the engine is still warm to assure rapid and complete draining,
1. Remove the oil filler cap and the drain plug, then drain the oil.
2. Reinstall the drain plug and tighten securely,
3. Refill with tha recommended ail {see page 10) to the specified level,
OIL CAPACITY: 0.6 £ (0.63 US at, 0.53 Imp qt}
(1) OIL FILLER CAP/DIPSTICK
(2) DRAIN PLUG
(3) OIL LEVEL
CAUTION: Used motor oil may cause skin cancer if repeatedly left in contact with
the skin for prolonged periods. Although this is unlikely unless you handle used oil
on a daily basis, it is still advisable to thoroughly wash your hands with soap and water
83 soon as possible after handling used oil.
NOTE: Please dispose of used motor oil in a manner that is compatible with the
environment. We suggest you take it in a sealed container to your local service station
for reclamation. Do not throw it in the trash or pour it on the ground.
2. Air cleaner service
A dirty air cleaner will restrict air flow to the carburetor. To prevent carburetor me
function, service the air cleaner regularly. Service more frequently when operating tr
pump in extremely dusty areas.
Do not use gasoline or low flash point solvents for cleaning. They a
flammable and explosive under certain conditions,
CAUTION: Never run the pump without the air cleaner. Rapid engine wear will ran
from contaminants such es dust and dirt being drawn into the engine.
1. Unscrew the wing nut, remove the air cleaner cover and remove the element,
2, Wash the element in a non-flammable or high flash point solvent and dry it thoroughl
3. Soak the element in clean engine oil and squeeze out the excess oil,
4. Reinstall the air cleaner element and the cover.
(1) AIR CLEANER COVER
{2} AIR CLEANER ELEMENT
3.
Spark plug service
Recommended spark plug: BPRBES [NGK)
W20EPR-U (NIPPONDENSO)
Го ensure proper engine operation, the spark plug must be properly gapped and free of
leposits.
Remove the spark plug cap.
If the engine has been running, the mufflar will ba vary hot. Be careful
10t to touch the muffler.
. Visually inspect the spark plug. Discard the spark plug if there is apparent wear, or
if the insulator is cracked or chipped, Clean the spark plug with a wire brush if it is
10 be reused,
. Measure the plug gap with a feeler gauge. The gap should be 0,77-0.8 mm {0.028—
0.031 in). Correct as necessary by bending the side electrode.
0.7 - 0.8 mm
4 (0028-0031)
4. Check that the spark plug washer is in good condition, and thread tha spark plug in by
hand to prevent cross-threading,
e их >>
DA ID |
“8
NX
VA
A
N
`
NOTE: If installing a new spark plug, tighten 1/2 turn after the spark plug seats to com-
press the washer, If reinstalling a used spark plug, tighten 1/8—1/4 turn after the spark
plug seats to compress the washer.
CAUTION: The spark plug must be securely tightaned, An improparly tightanad plug
can become very hot end possibly damage the engine. Never use a spark plug with an
impropar haat range.
9. TRANSPORTING/STORAGE
4. Change the engine oil,
5. Remove the spark plug, and pour about a tablespoon of clean engine oil into tt
cylinder. Crank the engine several revolutions to distribute the oil, then reinstall tt
® To avoid severe burns or fire hazards, let the engine cool before transporting the spark plug.
pump or storing it indoors. 6. Pull the starter grip until resistance is felt: Continue pulling until the notch on tt
* When transporting the pump, turn the fuel valve to the OFF position, and keep the starter pulley aligns with the hole an the recoil starter (see illustration below). At th
pump level to prevent fuel spillage. Spilled fuel or fuel vapor may ignile. point, the intake and exhaust valves are closed, and this will help to protect the engir
Before storing the pump for an extended period: from internal corrosion.
1. Be sure the storage area is free of excessive humidity and dust.
2. Clean the pump interiar . . ...
Sediment will settle in the pump if it has been used in muddy or sandy water, water
containing heavy debris. N re ООН
Pump clean water through the pump before shutting down or impeller may be a
damaged when restarting. After flushing, remove the pump drain plug, drain as much TTT,
water as possible from the pump housing and reinstall the plug.
3, Drain the fuel ..... Align the mark on the startar pulley
a. With the fuel valve OFF, remove the drain screw from carburetor float bowl and with the hole at the top of racoll
drain the carburetor, Drain the gasoline into a suitable container. starter.
b. Turn the fuel valve ON and drain the gasoline in the fuel tank into the suitable con:
tainer,
Cc. Reinstall the carburetor drain screw.
(1) PUMP DRAIN PLUG
(2) FLOAT BOWL
E 7, Cover the pump to keep out dust.
—95— —26—
10. TROUBLESHOOTING
Nhen the engine will not start;
1, Is there enough fuel?
2. Is the fuel valve on?
3. Is gasoline reaching the carburetor?
To check, loosen the drain screw with the fuel valve on.
If any fuel is spilled, make sure the area is dry before testing the spark
plug or starting the engine. Spilled {uel or fuel vapor may ignite.
(1) FLOAT BOWL
(2) DRAIN SCREW
| e —— | / :
© | ГО
О
4. Is the engine switch ON?
5_ Is there enough of in the engine?
6. Is the spark plug in good condition?
Remove and inspect the spark plug. Clean, readjust gap and dry the spark plug.
Replace il if necessary.
7. If the engine still does not start, take the pump to an autharized Honda dealer.
When the pump cannot pump the water;
1. Is the pump fully primed?
. |s the strainer clogged?
. Are the hose bands installed securely?
. Are the hoses damaged?
, |s the suction head too high?
. If the pump still does not operate, take the pump to ап authorized Honda dealer.
Ch NM à 0 59
11. SPECIFICATIONS
Dimensions and Waight
Model
WP20X
Power product
daseription code
WZBE
Length x Width x Height
" 470 x 350 x 380 mm
{18.5 x 13.8 x 15.0 in}
*" 470 x 350 x 360 mm
(18.5 x 13.8 x 14.2 in)
Dry weight
22 kg {48.5 Ibs)
*- With cushion rubber
ȴ. Without cushion rubber
Dimensions and Weight
Medal
WP30X
Power product
description code
WZBF
Length x Width x Height
* 505 x 375 x 465 mm
(19,9 x 14,8 x 18.3 in)
“+ 505 х 375 x 450 mm
(19,9 x 14.6 x 17,7 in)
Dry weight
28 kg (61.7 lbs)
*: With cushion rubber
"+ Without cushion rubber
Engine
Model GX120
Engine type 4-stroke, overhead valve, single cylinder
Displacemant
118 cm?’ (7.2 cuan)
Engine
Model GX1E60
Engine type 4-stroke, overhead valve, single cylinder
Cisplacemant
163 cm! (9.9 cu in)
Rare x Stroke
50 x 42 mm (2.4 x 1.7 in)
Bare x Stroke
BB x 45 mm (2.7 x 1.8 in)
Max. output
2.9 kW {4.0 PS) at 4,000 rpm
Max, output
4.0 kW {5.5 PS) at 4,000 rpm
Max. torque
7.4 N-m {0.75 kgl-m, 5.0 Lbf-ft) at 2.500 rpm
Max. torque
10.8 N-m {1.1 kgf-m, 2.0 (bFIt) at 2,500 rpm
Cooling system
Forced air
Cooling system
Forced air
lgnition system
Transistorized magneto
Ignition system
Transistorized magneto
PTO shaft rotation
Counterclockwise
PTO shaft rotation
Counterclockwise
Pump
Suction port diameter 50 mm {2 in)
Discharge port diameter 50 mm (Zin)
Rated revolutions 3,600 rpm
Total head 26 m (85.3 ft)
Suction head В т (27.9 ft)
Capacity 600 ¢ (158 US gal, 132 Imp ое Ат
Continuaus running time 2.2 hrs,
Sound prey UPN 0 dE
Guaranteed sound power level 103 dB
(Lwa) Tested by 2000/14/EC
Pump
Suction part diameter 80 mm (3,1 in)
Discharge port diameter 80 mm (3.1 in)
Rated revolutions 3,600 rpm
Total head 30 m (98.4 ft)
Suction head В т {27.9 ft)
Capacity 1,000 ¢ {264 US gal, 220 Imp gall/min
Continuous running time 2.4 hrs.
ra pres DN 01 de
Guaranteed sound power level 105 dB
{Lwa) Tested by 2000/14/EC
NOTE: Specifications are subject to change without notice due to
improvement.
NOTE: Specifications are subject ta change without notice due to
improvement.
12. MAJOR Honda DISTRIBUTOR ADDRESSES IN EUROPE
For European
For European (continued)
NAME OF FIRM [COMPANY]
ADDRESS
TEL: FAX:
Honda [UK.} Limited
470 London Road, Slough,
Earkshira, SLIBOY,
Uniled Kingdom
Tel: 91757-550-580
Fax: 01753-590-000
Hondo Europa Powar Equipmant S.A.
Folo 45 Ruo des Cholaignlers
45740 Ormos
France
Tol: 1-38-65-05-00
Fax: 1-38-65-06-05
Honda Doulschlond GmbH,
Sprendiingar, Landstro6g 166
C-63063 Ofrenbech'Main
Tai: 059-83-09-0
Fax: 0655-B3-09-519
083320, Lo Gorrign
[Barcolanal, Spain
NAME OF FIRM (COMPANY ADDRESS TEL: FAX:
OY Brandt AB Tuupakantio 4 Tol: 90-895-501
SF-01240, Vantaa Fax: #0-875-5276
Finland
TIMA PRODUCTS A/S Tärnfalkavai 16, Posiboks 511 Tal: 71-43-17.00
DK 2650 Hridovro Fax: 3677-16-30
Denmark
Greans Polig.Industriol Congos1 Tel: 93-871-84-50
Fax; D3-871-81-B0
Gormany
Honda Belgium HY, Wiingaardveld 1, 9300 Aalst Tol: 053-725-111
Balgium Fox: 053-725-100
Honda lralia Industriala 5.P.A. Via della Corchlgnola, 577 Tal: 06-54928-1
00143 ROMA Fox: 06-54928-400
Honda (Suissa) S.A,
Routa des Moulières 10
Caso Poslale Ch 1214
Yarnior-Genavao, Switzerland
Tuo): 022-34 1-22-00
Fax: 022-341-09-72
Aulomocion Canarios 5.4. (AUCASA)
Apartado, de Correos, num 206
Soma Cruz de Tonorifa
Canary lslond
Tol: 922-61-13-50
Fax: 922-651-1344
Honda Moderlond В.М.
Mikkolstraol 17
Tal: 018-04-57-333
2984 Riddorkork Fax: 015-04-91-888
Nolhodonds
Honda Austrio G.M.B.K. Honda Strasse 1 À-2351 Tel: 223-65-500
Wionar Neudort Fox: 223-566-4110
Auslria
Croch Rapublic
The Associated Motors Company Lid, 148, Aug D'Arguns, Mslido Tal: 356-23300 1
Malın Fox: 356-340473
Two Whnmals Ltd. Crosslands Businoss Park, Tal; 602111
Ballymount Aoad, Dublin 12, Fax: 4566579
Ireland
Gonaral Automolivo Co, S.À. P.O. Box 1200, 101 73 Athons Tal: 345-5321
Grèoce Fax: 346-7329
BG Technik 5.r.0, Radlickd 117/520 Tal: 2-5694 573
158 01 Proha 6 Fox: 2-5694 571
Honda Powar Equipment Sweden A.B.
Ssimástargránd B
Slockhoim-Arsta
Sweden
Tol; 08-502-24-50)
Fax: 08-722-36-27
Honda Produtos Do Farga, Portugal, 5.4.
Lugar da Abrurhairg
S. Pedro de Ponalerrim
2710 Sintra, Portupa!
Tal:351-1-9150374
Fox:351-1-9111021
Bardma ASS
Herghagon 5, Longhus
Hox 454, 1401 Ski
Norway
Tel: 64-66-05-C0
Fax: 54-85-0549
Aros Power Equipment Lid, 01-433 Warazawy, Tal: 22-685 17 06
ul Wroclawska 250 Fax: 22-665 16 03
Poland
MO.TOR.PEDO Ltd, 1134 Hudopasi, Tel: 1-4652080
Odzsa Gy-ur 61-63. Fox: 1-4652081
Hungary
For Canadian
NAME OF FIRM COMPANY) ADDRESS TEL: FAX:
Honda Canada Ine. 715 Milnor Avenue Tol: 1-888-946-6329
Toronto ON Fax: 1-897-039-0909
M18 2KB