RAB Lighting DSK4R11827120W Surface & Flush Mount Instructions

Add to My manuals
2 Pages

advertisement

RAB Lighting DSK4R11827120W Surface & Flush Mount Instructions | Manualzz

4” DISK DOWNLIGHT

IMPORTANT

DSK4R119XX120W

TO PREVENT ELECTRICAL SHOCK, POWER SHOULD BE TURNED OFF AT THE FUSE BOX BEFORE INSTALLATION.

SAFETY WARNINGS:

Read all product labels and directions.

input rating of the luminaire.

local codes. Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.

• WARNING – To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.

• Replace only with RAB Lighting Inc. Visit our website: RABLIGHTING.COM Call our experts at 888 722-1000

MODEL# DSK4R118XX120W DSK4R119XX120W.

• The recessed luminaire is intended for mounting only in a covered ceiling where only the led side of the luminaire will be exposed to damp or dry or wet locations.

• INSTALLATION SHOULD ONLY BE PERFORMED AFTER POWER TO THE FIXTURE HAS BEEN DISCONNECTED.

• These instructions shall be included on an information sheet packaged with each unit.

WHAT’S IN THE BOX

ATT

THIS LUMINAIRE HAS BEEN MODIFIED TO OPERATE LED LAMPS.

T

REPLACE ONLY WITH RAB Lighting Inc.

RABLIGHTING.COM 888 722-1000

MODEL#

OPTIONAL ACCESSORIES

Our disk downlight is compatible with most common 4” recessed housings, please purchase the LAMPSOCKET E26 SET

( Model# DSK4/ACC - including E26 adapter, female connector and friction clips) for installation in housings.

Disk (1) Screws (2) Nuts (3) Lumi Sticker (1)

TOOLS NEEDED

Installation with J-BOX

A screwdriver is needed for installation.

Installation with Existing Housing

No tools are necessary for installation.

DIMENSIONAL DRAWINGS

E26 adapter(1) Female connector(1) Friction Clips (3)

MIN. LAMP COMPARTMENT DIMENSIONS

Installation with J-BOX

J-box Min Volume - 18 in 3 , Min Length: 3.5in, Height: 2.19in

Compatible with standard J-box

Installation with Existing Housing

Min lamp compartment dimensions - Dia: 4in, Height: 5.9in

Compatible with most common 4in recessed housings

1 3/4”

1 1/8”

5 1/2”

4” DISK DOWNLIGHT

INSTALLATION WITH J-BOX

1. Make sure the POWER IS TURNED OFF at the source to the J-box in which you are installing the product.

2. Squeeze the clips and take out bracket from disk. (Fig.1)

Fig: 1

Bracket

INSTALLATION WITH EXISTING HOUSING

1. Squeeze the clips and remove the bracket from disk, the bracket is

no need for installation with existing housing .

(Fig.5)

Fig: 5

Bracket

3. Connect the Ground Wire (green) to J-box, and fasten the bracket to J-box with the screws provided in package. (Fig.2) Pay attention to the direction of bracket.

Fig: 2

J-box

Ground wire

(green)

Bracket

Bracket installation

J-box

Correct

J-box

Wrong

F

Screw*2

4. Connect the wires of J-box to disk, white - white, black - black.

(Fig.3)

Fig: 3

Nuts

JBOX

Black (line)

Ground

White (neutral)

Black (line)

Green (ground)

White (neutral)

DISK

2. Make sure the POWER IS TURNED OFF at the source to the recessed housing in which you are installing the product.

3. Wire the disk with female connector. (Fig.6) Insert the black wire into the side marked (+) and the white wire into the side marked (-).

Make sure both wires are tightly secured.

Fig: 6

White wire

Black wire Female connector

4. Install the friction clip on the back of the Downlight.

(Fig. 7)

Fig: 7

Friction Clips

5. Screw the E26 adapter into the socket. Then connect male connector of E26 adapter to the female connector of the disk. (Fig. 8)

Fig: 8

5. Push disk up into the mounting bracket until it clicks into place

(Fig.4) .

Fig: 4

Housing

E26 adapter

Disk

6. Simply slide the trim and metal friction clips into the housing. (Fig.9)

Fig: 9

(Fig. 10)

Fig: 10

Easy Answers v

advertisement

Related manuals

advertisement