SoundPEATS Truengine SE Earbud Headphone User Manual

Add to My manuals
1 Pages


SoundPEATS Truengine SE User Manual - Download & Read Online | Manualzz
 Truengine SE >;
USER MANUAL | Manuel d'Utilisation | Bedienungsanleitung |
Manual de Instrucciones | Manuale di istruzioni | Nika | 880
Package Content
Product Diagram
Button Controls
Once connected, the Truengine SE headphones can control media and phone
cals from a phone or tablet.
Function Operation
Power On Automatic: Take out earbuds from charging case
Manual: Long press Multifunction button for 1.5s while
earbuds are off
7O EY ——al
0 O
Bluetooth Version Bluetooth 5.0
Bluetooth Chipset QCC3020
Audio Decode Apt-X AAC SBC
Maximum Working Range 33 feet/10m (no obstacie)
Playing Time About 6 hours
Earbuds Charging Time About 2 hours
Charging Time of Charging Case 2.5 hours
Charging Case Recharge Earphones | 3.5 times
Earpiece Dimension (L * W * H)
Power Off Automatic: Place earbuds back info charging case
Manual: Long press Multifunction button for 8s while
earbuds are on
Volume Up Double tap right Multifunction button
Volume Down Double tap left Multfunction button
Play Previous Long press the left Multifunction button for 1.5s
Multifunction button for 1.5s
button once
button for1.5s
Siri for IOS devices)
Wearing the earphones
1. Identify left and right earbud.
2. Adjust earbuds to find the most
comfortable place. ( e
3. Insert earbuds to ensure seal well
your ear channel.
Getting Started
1. Left and right earbud will pair with each other when take out both earbuds
simutaneously from charging case with power. Next the led indicator of left
earbud will goes out, and led indicator on right earbud will flash red and
white alternately and you can hear voice prompt “pairing”, which indicates
that earbuds succeed in entering pairing mode.
2. Please find the name of "SOUNDPEATS Truengine SE” on the bluetooth list of
your phone, click to connect, you can hear voice prompt “connected” from
right earbud. Then you will get a pairing request again, please continue to
click” SOUNDPEATS Truengine SE L” to connect.
Bluetooth Pairing Request
108 “Headset” would like to pair with your iphone.
Cancel | Pair ху
Bluetooth Pairing Request
Andriod Pair with SOUNDPEATS Truengine SEL ?
Cancel | Pair y
3. SOUNDPEATS Truengine SE Headphones can remember devices previously
paired . If you have paired earbuds with a device once, simply activate the
bluetooth on your device, take out earbuds from charging case and close
the lid, they will automatically reconnect with that device. If earbuds don’t
automatically connect, select the earbuds name on your bluetooth device
to connect.
4. Play in mono mode: Left and right earbud can be used separately when
SOUNDPEATS Truengine SE have paired successfully.
1. When SOUNDPEATS Truengine SE L Headphones request pairing, please select
pairing, otherwise earbuds can’t be used in mono mode.
2. When SOUNDPEATS Truengine SE Headphones connect with phone equipped
with Qualcomm Snapdragon 855 and higher version chipset, there will be two
pairing name appeared on the bluetooth list and both of them will automati-
cally connect, you don't need to do the second pairing by manual.
3.1f you want to change pairing device but already in “connected” status with
previous one, you can force earbuds to enter into pairing mode-only need
press the Multifunction button for 5s.
Factory Reset
(Try the following steps if you fail to build connection between two earpieces or
earbuds to device)
1. Delete pairing name from your device's bluetooth list.
2.Place both erabuds back into the charging case and ensure that both
earbuds are in charging status, press and hold both multifunction buttons for
5s until both indicators flash in white twice. Reset complete.
SOUNDPEATS Truengine SE are equipped with a charging case which is not only a
charging dock to charge the headphones but also a carrying case with built-in
rechargeable battery, the charging case can provide up to 3.5 times full charge for
both headphones.
Charging the headphones
The headphones are partially charged at the factory. Please make sure they are full
charged before first use.
1. Put the earbuds into corresponding charging slots, make sure the charging
contactors are attached.
2. The LED indicators on the headphones turns red to start charging.
3. The headphones are fully charged when LED indicators lights out.
Charging the case
When the charging case is in low battery level,
only one white led indicator flashes, please
recharge the case:
1. Connect the charging port with USB charging
adapter or computer USB port.(current less than
5V 1A)
2. Please charge the earphones at least once
every 3 months when not in use for a long time.
We warrant this device 12 MONTHS from date of the original purchase for manufacturer
If the device fails due to a manufacturing defect, please contact seller directly to initiate
return and warranty process.
support@ peat com
@ www dpeat li
Please scan QR code to know the PDF user manual.


Key Features

  • Bluetooth 5.0 connectivity
  • Apt-X codec support
  • 6 hours playtime
  • 21 hours with charging case
  • Touch controls
  • Mono and stereo modes

Related manuals

Frequently Answers and Questions

Can I use the earbuds with my computer?
Yes, the SoundPEATS Truengine SE can be paired with any Bluetooth device, including computers.
How do I reset the earbuds to factory settings?
To reset the earbuds, place them in the charging case, and press and hold both multifunction buttons for 5 seconds until the indicators flash white twice.
How do I pair the earbuds with a new device?
Delete the pairing name from your device's bluetooth list, place both earbuds back into the charging case and ensure that both earbuds are in charging status, press and hold both multifunction buttons for 5s until both indicators flash in white twice. Then take out the earbuds from the charging case and follow the pairing instructions in the manual.