Tappan MSH1BE, FSH1BE, ESH1BE, WSH2BE, HSH1BE, PSH1BE, GSH2BE, BSH2BE, CSH1BE, VSH1BE Installation guide

Tappan MSH1BE, FSH1BE, ESH1BE, WSH2BE, HSH1BE, PSH1BE, GSH2BE, BSH2BE, CSH1BE, VSH1BE Installation guide
SPLIT SYSTEM HEAT PUMP
14 SEER
INSTALLATION INSTRUCTIONS
*SH(1,2)BE4M1 - SP18K, (R,S)P24K, (R,S)P30K, SP36K, SP42K, SP48K, & SP60K
(1.5, 2, 2.5, 3, 3.5, 4, & 5 TON) SERIES, SINGLE PHASE MODELS WITH MICROCHANNEL COILS
IMPORTANT
ATTENTION INSTALLERS:
It is your responsibility to know this product better
than your customer. This includes being able to install
the product according to strict safety guidelines and
instructing the customer on how to operate and maintain
the equipment for the life of the product. Safety should
always be the deciding factor when installing this product
and using common sense plays an important role as well.
Pay attention to all safety warnings and any other special
notes highlighted in the manual. Improper installation of
the unit or failure to follow safety warnings could result
in serious injury, death, or property damage.
These instructions are primarily intended to assist
qualified individuals experienced in the proper installation
of this appliance. Some local codes require licensed
installation/service personnel for this type of equipment.
Please read all instructions carefully before starting the
installation. Return these instructions to the customer’s
package for future reference.
DO NOT DESTROY. PLEASE READ CAREFULLY &
KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.
IMPORTANT SAFETY INFORMATION........................... 2
HEAT PUMP INSTALLATION......................................... 3
General Information................................................................... 3
Before You Install the Heat Pump.............................................. 3
Locating the Heat Pump............................................................ 3
Packaging Removal................................................................... 3
Ground Level............................................................................. 3
Rooftop...................................................................................... 3
Connecting Refrigerant Tubing Between the Indoor
& Outdoor Unit........................................................................... 4
Outdoor Orifice Removal & Installation...................................... 4
ELECTRICAL WIRING.................................................... 5
Pre-Electrical Checklist.............................................................. 5
Line Voltage............................................................................... 5
Grounding.................................................................................. 5
Thermostat / Low Voltage Connections..................................... 5
CoreSenseTM Diagnostics Module............................................. 6
Compressor Protection........................................................... 6
Resetting Alert Codes............................................................. 6
START UP & ADJUSTMENTS........................................ 7
Pre-Start Check List.................................................................. 7
Start-Up Procedures.................................................................. 7
Operating Temperatures......................................................... 7
Air Circulation - Indoor Blower................................................... 7
Short Cycle Protection............................................................... 7
System Cooling.......................................................................... 7
System Heating......................................................................... 7
Defrost Control Board Test Pins................................................. 7
HEAT PUMP MAINTENANCE......................................... 8
Panel Removal........................................................................... 8
Panel Installation....................................................................... 8
REFRIGERANT CHARGING........................................... 9
Charging the Unit in AC mode................................................... 9
If the outdoor temperature is 65 degrees F or higher:............ 9
If the outdoor temperature is between 35 degrees F
and 65 degrees F:................................................................... 9
If the outdoor temperature is below 35 degrees F:................. 10
WIRING DIAGRAMS........................................................ 11
Figure 9. Wiring Diagram for *SH(1,2)BE4M1SP with
Low Pressure Switch............................................. 11
Figure 10. Wiring Diagram for *SH1BE4M1SPwith
CoreSenseTM and Low Pressure Switch............... 12
Figure 11. Wiring Diagram for *SH1BE4M1SP with Low
Pressure Switch (Manufactured Housing)........... 13
Figure 12. Wiring Diagram for *SH2BE4M1RP
(Manufactured Housing)...................................... 14
Figure 13. Wiring Diagram for *SH2BE4M1SP
(Manufactured Housing)...................................... 15
Figure 14. Wiring Diagram for *SH2BE4M1RP
(Builder's Series)................................................. 16
Figure 15. Wiring Diagram for *SH2BE4M1SP
(Builder's Series)................................................. 17
INSTALLATION CHECKLIST.......................................... 20
REPLACEMENT PARTS................................................. 20
IMPORTANT SAFETY INFORMATION
INSTALLER: Please read all instructions before servicing
this equipment. Pay attention to all safety warnings and
any other special notes highlighted in the manual. Safety
markings are used frequently throughout this manual to
designate a degree or level of seriousness and should not
be ignored. WARNING indicates a potentially hazardous
situation that if not avoided, could result in personal injury or
death. CAUTION indicates a potentially hazardous situation
that if not avoided, may result in minor or moderate injury
or property damage.
WARNING:
ELECTRICAL SHOCK, FIRE OR
EXPLOSION HAZARD
Failure to follow safety warnings exactly could
result in serious injury or property damage.
Improper servicing could result in dangerous
operation, serious injury, death or property
damage.
• Before servicing, disconnect all electrical power
to the unit.
• When servicing controls, label all wires prior
to disconnecting. Reconnect wires correctly.
• Verify proper operation after servicing.
WARNING:
This split system heat pumps is shipped charged
with R410A refrigerant and ready for installation.
If repairs make it necessary for evacuation and
charging, it should only be attempted by qualified
trained personnel thoroughly familiar with this
equipment. Under no circumstances should
the owner attempt to install and/or service this
equipment. Failure to comply with this warning
could result in property damage, personal injury,
or death.
CAUTION:
This unit uses R-410A refrigerant. DO NOT use
any other refrigerant in this unit. Use of another
refrigerant will damage the unit.
2
WARNING:
Unless noted otherwise in these instructions,
only factory authorized parts or accessory
kits may be used with this product. Improper
installation, service, adjustment, or maintenance
may cause explosion, fire, electrical shock or
other hazardous conditions which may result in
personal injury or property damage.
• Installation of equipment may require brazing operations.
Installer must comply with safety codes and wear
appropriate safety equipment (safety glasses, work gloves,
fire extinguisher, etc.) when performing brazing operations.
• Follow all precautions in the literature, on tags, and on
labels provided with the equipment. Read and thoroughly
understand the instructions provided with the equipment
prior to performing the installation and operational checkout
of the equipment.
• Use caution when handling this appliance or removing
components. Personal injury can occur from sharp metal
edges present in all sheet metal constructed equipment.
WARNING:
The information listed below and the next page
must be followed during the installation, service,
and operation of this equipment. Failure to follow
safety recommendations could result in possible
damage to the equipment, serious personal injury
or death.
• The installer must comply with all local codes and
regulations which govern the installation of this type of
equipment. Local codes and regulations take precedence
over any recommendations contained in these instructions.
Consult local building codes and the National Electrical
Code (ANSI CI) for special installation requirements.
• All electrical wiring must be completed in accordance with
local, state and national codes and regulations and with
the National Electric Code (ANSI/NFPA 70) or in Canada
the Canadian Electric Code Part 1 CSA C.22.1.
• This equipment contains liquid and gaseous refrigerant
under high pressure. DO NOT USE ANY PORTION OF
THE CHARGE FOR PURGING OR LEAK TESTING.
Installation or servicing should only be performed by
qualified trained personnel thoroughly familiar with this
type equipment.
• Fully annealed, refrigerant grade copper tubing should
be used when installing the system. Refrigerant suction
line tubing should be fully insulated.
• This unit is designed for outdoor installations only and
should be positioned as shown on page 3.
HEAT PUMP INSTALLATION
General Information
*SH(1,2)BE4M1 split system heat pumps are designed only
for outdoor rooftop or ground level installations. This unit
has been tested for capacity and efficiency in accordance
with AHRI Standards and will provide many years of safe
and dependable comfort, providing it is properly installed
and maintained. Abuse, improper use, and/or improper
maintenance can shorten the life of the appliance and create
unsafe hazards.
To achieve optimum performance and minimize equipment
failure, it is recommended that periodic maintenance be
performed on this unit. The ability to properly perform
maintenance on this equipment requires certain mechanical
skills and tools.
Refer to the Quick Reference Data sheet for additional
electrical, charging and unit information.
Before You Install the Heat Pump
√ The cooling load of the area to be conditioned must be
calculated and a system of the proper capacity selected.
It is recommended that the area to be conditioned be
completely insulated and vapor sealed.
√ Check the electrical supply and verify the power supply
is adequate for unit operation. The system must be wired
and provided with circuit protection in accordance with
local building codes. If there is any question concerning
the power supply, contact the local power company.
√ The indoor section (air handler, furnace, etc) should be
installed before routing the refrigerant tubing. Refer to
the indoor unit's installation instructions for installation
details.
√ All units are securely packed at the time of shipment and
upon arrival should be carefully inspected for damage prior
to installing the equipment at the job site. Verify coil fins
are straight. If necessary, comb fins to remove flattened
or bent fins. Claims for damage (apparent or concealed)
should be filed immediately with the carrier.
√ Please consult your dealer for maintenance information
and availability of maintenance contracts. Please read all
instructions before installing the unit.
Packaging Removal
To prevent damage to the tubing onnections, carefully remove
the carton and user’s manual from the equipment. Discard
the shipping carton.
Ground Level
Ground level installations must be located according to local
building codes or ordinances and these requirements:
• Clearances must be in accordance with those shown in
Figure 1.
• A suitable mounting pad must be provided and be separate
from the building foundation. The pad must be level and
strong enough to support the unit’s weight. The slab height
must be a minimum of 2” (5 cm) above grade and with
adequate drainage. See Figure 1.
Rooftop
• The method of mounting should be designed so that it
does not overload roof structures or transmit noise to
the interior of the structure. The roof must be structurally
capable of handling the weight of the unit.
• Full perimeter support is required under the unit. Support
must be made of weather resistant materials and installed
prior to unit installation.
• The support must be built to raise the unit 6" above the
roof.
6” from Building
or Structure
24" for
Service Access
12" or 18”
See Note
DO NOT
OBSTRUCT
TOP OF UNIT
12" or 18”
See Note
NOTE: Units require full perimeter clearances.
Installer must maintain 18” between two units
or 12” between single unit and structure.
Locating the Heat Pump
• Survey the job site to determine the best location for
mounting the outdoor unit.
• Overhead obstructions, poorly ventilated areas, and areas
subject to accumulation of debris should be avoided. See
Figure 1.
• Sufficient clearance for unobstructed airflow through the
outdoor coil must be maintained in order to achieve rated
performance. See Figure 1 for minimum clearances to
obstructions.
• Consideration should be given to availability of electric
power, service access, noise, and shade.
48”
2” Mounting Pad
Figure 1. Clearance Requirements
3
Connecting Refrigerant Tubing Between the Indoor
& Outdoor Unit
CAUTION:
When servicing, cover or seal openings to
minimize the exposure of the refrigerant system
to air to prevent accumulation of moisture and
other contaminants.
After outdoor and indoor unit placement has been determined,
route refrigerant tubing between the equipment in accordance
with sound installation practices.
• When connecting refrigerant linesets together, it is
recommended that dry nitrogen be flowing through the
joints during brazing. This will prevent internal oxidation
and scaling from occurring.
• Refrigerant tubing should be routed in a manner that
minimizes the length of tubing and the number of bends
in the tubing.
• Refrigerant tubing should be supported in a manner
that the tubing will not vibrate or abrade during system
operation.
• Tubing should be kept clean of foreign debris during
installation.
• Every effort should be made by the installer to ensure
that the field installed refrigerant containing components
of the system have been installed in accordance with
these instructions and sound installation practices to
insure reliable system operation and longevity.
• The maximum recommended interconnecting refrigerant
line length is 75 feet, and the vertical elevation difference
between the indoor and outdoor sections should not
exceed 20 feet.
• If precise forming of refrigerant lines is required, a copper
tubing bender is recommended. Avoid sharp bends and
contact of the refrigerant lines with metal surfaces.
• A filter dryer is provided with the unit and must be
installed in the liquid line of the system. If the installation
replaces a system with a filter dryer already present in the
liquid line, the filter dryer must be replaced with the one
supplied with the unit. The filter dryer must be installed
in strict accordance with the manufacturer’s installation
instructions.
• Optional equipment such as liquid line solenoid valves,
low ambient, etc., should be installed in strict accordance
with the manufacturer’s installation instructions.
Outdoor Orifice Removal & Installation
CAUTION:
When servicing, cover or seal openings to
minimize the exposure of the refrigerant system
to air to prevent accumulation of moisture and
other contaminants.
CAUTION:
To prevent damage to the unit or internal
components, it is recommended that two
wrenches be used when loosening or tightening
nuts. Do not over tighten!
1. Using two wrenches loosen the nut and liquid valve. Turn
the assembly nut counter-clockwise until the orifice body
halves are separated.
2. Insert a light-gauge wire hook between the valve body
and the restrictor orifice while being careful not to scratch
either part. Carefully remove the restrictor orifice from the
valve body. See Figure 3.
Liquid
Valve
Restrictor
Swivel Nut
Figure 2. Liquid Valve, Restrictor, &
Swivel Nut Adapter
The orifice installed in the outdoor unit has been sized for use
with the most popularly matched indoor units. Depending
on the indoor coil that the unit is being matched with, the
outdoor restrictor may need to be changed. Please refer
to the Quick Reference Data sheet that is supplied with the
outdoor unit for more information.
If the outdoor unit has the liquid valve shown in Figure 2, then
the restrictor is located inside the swivel nut connection of
the liquid valve and not inside the outdoor unit’s distributor.
Perform steps 1 - 5 if the outdoor restrictor needs to be
changed.
Figure 3. Removal of Orifice
4
3. Check the actual size of the new orifice. NOTE: The size
is stamped on its side. Do not use pin gauges to measure
the orifice diameter.
4. Insert the new orifice into the valve body, with the rounded
end facing into the valve. See Figure 2 (page 4).
•
CAUTION:
To prevent damage to the unit or internal
components, it is recommended that two
wrenches be used when loosening or tightening
nuts. Do not over tighten!
5. Realign the assembly nut on the valve body and hand
tighten both components. Mark a line on both bodies and
then tighten an additional ¼ turn using two wrenches. The
movement of the two lines will show how much the nut is
tightened.
•
•
ELECTRICAL WIRING
WARNING:
To avoid risk of electrical shock, personal
injury, or death, disconnect all electrical power
to the unit before performing any maintenance
or service. The unit may have more than one
electrical supply.
•
•
electrical conductors and circuit protection must be in
compliance with information listed on the outdoor unit
data label. Any other wiring methods must be acceptable
to authority having jurisdiction.
The outdoor unit requires both power and control circuit
electrical connections. Refer to the wiring diagrams for
identification and location of outdoor unit field wiring
interfaces. See Figure 9 (page 11), Figure 10 (page
12), Figure 11 (page 13)) Figure 12 (page 14),
Figure 13 (page 15), Figure 14 (page 16), & Figure 15
(page 17). Make all electrical connections in accordance
with all applicable codes and ordinances.
Overcurrent protection must be provided at the branch
circuit distribution panel and sized as shown on the unit
rating label and according to applicable local codes. See
the unit rating plate for minimum circuit ampacity and
maximum overcurrent protection limits.
Provide power supply for the unit in accordance with the
unit wiring diagram, and the unit rating plate. Connect the
line-voltage leads to the terminals on the contactor inside
the control compartment.
Use only copper wire for the line voltage power supply to
this unit in strict accordance of the NEC (ANSI/NFPA 70),
applicable local codes, and the instructions provided with
the equipment. Use proper code agency listed conduit
and a conduit connector for connecting the supply wires
to the unit. Use of rain tight conduit is recommended.
208/230 Volt units are shipped from the factory wired for
230 volt operation. For 208V operation, remove the lead
from the transformer terminal marked 240V and connect
it to the terminal marked 208V.
Optional equipment requiring connection to the power or
control circuits must be wired in strict accordance of the
NEC (ANSI/NFPA 70), applicable local codes, and the
instructions provided with the equipment.
Label all wires prior to disconnection when
servicing the unit. Wiring errors can cause
improper and dangerous operation.
•
• All electrical connections must be in compliance with all
applicable local codes and ordinances, and with the current
revision of the National Electric Code (ANSI/NFPA 70).
• For Canadian installations the electrical connections and
grounding shall comply with the current Canadian Electrical
Code (CSA C22.1 and/or local codes).
Grounding
Pre-Electrical Checklist
√ Verify that the voltage, frequency, and phase of the supply
source match the specifications on the unit rating plate.
√ Verify that the service provided by the utility is sufficient
to handle the additional load imposed by this equipment.
Refer to the unit wiring label for proper high and low
voltage wiring.
√ Verify factory wiring is in accordance with the unit wiring
diagram. Inspect for loose connections. See Figure 9
(page 11), Figure 10 (page 12), Figure 11 (page
13)) Figure 12 (page 14), Figure 13 (page 15),
Figure 14 (page 16), & Figure 15 (page 17).
Line Voltage
• A wiring diagram is located on the inside cover of the
electrical box of the outdoor unit. The installer should
become familiar with the wiring diagram before making
any electrical connections to the outdoor unit.
• An electrical disconnect must be located within sight
of and readily accessible to the unit. This switch shall
be capable of electrically de-energizing the outdoor unit.
• Line voltage to the unit should be supplied from a dedicated
branch circuit containing the correct fuse or circuit breaker
for the unit. Incoming field wiring and minimum size of
WARNING:
The unit cabinet must have an uninterrupted or
unbroken electrical ground to minimize personal
injury if an electrical fault should occur. Do not
use gas piping as an electrical ground!
This unit must be electrically grounded in accordance with
local codes or, in the absence of local codes, with the National
Electrical Code (ANSI/NFPA 70) or the CSA C22.1 Electrical
Code. Use the grounding lug provided in the control box for
grounding the unit.
Thermostat / Low Voltage Connections
• Thermostat connections should be made in accordance
with the instructions supplied with the thermostat and the
indoor equipment. A typical installation with a heat pump
thermostat and air handler is shown in Figure 4 (page
6).
• The outdoor unit is designed to operate from a 24 VAC
Class II control circuit. The control circuit wiring must
comply with the current provisions of the NEC (ANSI/NFPA
70) and with applicable local codes having jurisdiction.
• The low voltage wires must be properly connected to the
units low voltage terminal block.
• The thermostat should be mounted about 5 feet above the
5
ODT
(Optional)
W2
IN
G
Green
G
Red
R
R
W2
OUT
W
C
C
O
O
O
Y1
IN
Y
Y
Outdoor
Heat
Pump
R
White
E
Black
C
Thermostat
W2
Air Handler
floor on an inside wall. DO NOT install the thermostat on
an outside wall or any other location where its operation
may be adversely affected by radiant heat from fireplaces,
sunlight, or lighting fixtures, and convective heat from
warm air registers or electrical appliances. Refer to the
thermostat manufacturer’s instruction sheet for detailed
mounting and installation information.
CoreSenseTM Diagnostics Module
(Select Models Only)
The CoreSenseTM Diagnostics Module, Figure 5, is a
breakthrough innovation for troubleshooting heat pump and
air conditioning system failures. The module installs easily
in the electrical box of the outdoor unit near the compressor
contactor.By using the compressor as a sensor, CoreSense
Diagnostics helps the service technician more accurately
troubleshoot system and compressor fault conditions.
A flashing LED indicator communicates the ALERT code
and a diagnostic key is also imprinted on the side of the
module to quickly direct the technician to the root cause of a
problem. Alert identification codes are also listed in Table 1.
Compressor Protection
Figure 4. Typical Thermostat Connections
Compressor
Common Wire
Reset Button
The CoreSenseTM Diagnostics module utilizes proprietary
algorithms to protect the compressor and system from
repeated trips of system pressure controls and the compressor
internal overload. The protection terminal of the module should
be wired in series with the system low pressure and high
pressure cutouts, as well as the compressor contactor. When
the module detects a series of trips as described below, it
will activate a lockout feature that opens the normally closed
protection contacts in the module, thereby cutting power to
the contactor and shutting off the compressor.
Resetting Alert Codes
Run / Alert
(Yellow LED)
When the CoreSenseTM Diagnostics module has detected a
series of adverse conditions that have caused it to lockout
the compressor, and after the issue has been resolved, it
is necessary to manually reset the module in order to clear
the present alert code.
Trip / Lock
(Red LED)
The primary way of clearing the code and resetting the alert
is to press the reset button located on the module.
Figure 5. CoreSenseTM Diagnostics Module
ALERT CODE
NOTE: Pressing the reset will require a pin or a mini electronics
screwdriver. This button must be pressed and held for a
minimum of one second for the module to be reset. Pressing
LOCK LEVEL
LOCK INDICATION
Normal operation, no trip
N/A
N/A
Code1
Yellow Flash 1
Long run time. Compressor is on running for more than 18 hours.
(Code1 is disabled in Heat Pump Mode)
N/A
N/A
Code2
Yellow Flash 2
Compressor (pressure) trip. Compressor runs for 12 sec to 15 min followed
by a compressor trip condition lasting for more than 7 min.
4x consecutive
Red: Flash2
Yellow: Off
Code3
Yellow Flash 3
Pressure switch cycling. Compressor runs for 12 sec to 15 min followed
by a compressor trip lasting between 35 sec to 7 min.
4x consecutive
or 10x total
Red: Flash3
Yellow: Off
Code4
Yellow Flash 4
Locked rotor. Compressor trips within a compressor run time of 12 sec
and does not start within 35 sec.
10x consecutive
Red: Flash4
Yellow: Off
Code5
Yellow Flash 5
Compressor (moderate run) trip. Compressor runs for 15 min to 18 hrs
followed by a compressor trip lasting longer than 7 min.
4x consecutive
or 10x total
Red: Flash5
Yellow: Off
Current >2A
for 40ms
Red: Flash9
Yellow: Off
N/A
N/A
Normal Run
Solid Yellow
Code9
Red Flash 9
Trip
Solid Red
ALERT CONDITION
The current to the PROT terminal is greater than 2A.
Demand is present, but compressor is not running.
Table 1. LED Diagnostics for CoreSenseTM Diagnostics Module
6
the reset button clears the immediate lock code and the seven
day operating history. It will not clear the permanent module
history. In the case of the three-wire module, the codes can
be reset or cleared by cycling power to the module. This can
be done by disengaging the Common (C) terminal. This will
not clear the seven day operating history.
START UP & ADJUSTMENTS
Pre-Start Check List
√ Verify the unit is level and has sufficient clearances for
unobstructed airflow.
√ Verify the outdoor coil and top of the unit are free from
obstructions and debris, and all equipment access/control
panels are in place.
√ Verify that the line voltage power leads are securely
connected and the unit is properly grounded.
√ Verify that the low voltage wires are securely connected
to the correct leads on the low voltage terminal strip.
√ Verify that the power supply branch circuit overcurrent
protection is sized properly.
√ Verify that the thermostat is wired correctly.
Start-Up Procedures
WARNING:
This unit is equipped with a crankcase heater.
Allow 24 hours prior to continuing the start up
procedures to allow for heating of the refrigerant
compressor crankcase. Failure to comply may
result in damage and could cause premature
failure of the system. This warning should be
followed at initial start up and any time the power
has been removed for 12 hours or longer.
Operating Temperatures
This equipment has been designed to operate within the
temperatures specified in Table 2. Running the equipment
in heating at higher than 70°F may require the use of a
Heat Pump Mild Weather Control Kit or changing over to
emergency or auxiliary heating.
Air Circulation - Indoor Blower
1. Set the thermostat system mode on OFF and the fan mode
to ON.
2. Verify the blower runs continuously. Check the air delivery
at the supply registers and adjust register openings for
balanced air distribution. If insufficient air is detected,
examine ductwork for leaks or obstructions.
3. Set the thermostat fan mode to AUTO and verify the blower
stops running.
Short Cycle Protection
1. Set the thermostat system mode to COOL. Observe the
temperature setting of the thermostat and gradually raise
the set-point temperature until the unit de-energizes.
2. Immediately lower the set point temperature of the
thermostat to its original setting and verify that the indoor
blower is energized and outdoor unit remains de-energized.
3. After approximately 5 minutes, verify the outdoor unit
energizes and the temperature of the discharge air is
cooler than the room temperature.
System Cooling
1. Set the thermostat’s system mode to COOL and the fan
mode to AUTO. Gradually lower the thermostat temperature
setpoint below room temperature and verify the outdoor
unit and indoor blower energize.
2. Verify blower wheel is spinning in direction indicated by
arrow. Feel the air being circulated by the indoor blower
and verify that it is cooler than ambient temperature. Listen
for any unusual noises. If unusual sounds occur, determine
the source of the noise and correct as necessary.
3. Verify HI and LO refrigerant pressures.
4. Allow the system to operate for several minutes and then
set the temperature selector above room temperature.
Verify the fan and compressor cycle off with the thermostat.
NOTE: The blower should also stop unless fan switch is
set to the ON position.
System Heating
1. Set the thermostat's system mode to HEAT and the
temperature mode to below room temperature.
2. Verify the outdoor unit and indoor fan stop running. After
5 minutes, increase the temperature on the thermostat to
it's maximum setting.
3. Verify the outdoor unit and indoor blower energize. Feel
the air being circulated by the indoor blower and verify
that it is warmer than ambient temperature. Listen for any
unusual noises. If unusual sounds occur, determine the
source of the noise and correct as necessary.
Defrost Control Board Test Pins
• Placing a jumper between the test pins for less than 1
second will bypass the Anti-Short Cycle Timer.
• Placing a jumper between the test pins for more than 1
second will force the unit into a defrost cycle. As soon
as the jumper is removed, the defrost cycle will end as
determined by the typical criteria.
• Verify the Status Indicator (on the control board) against
the codes listed in Table 3 to determine proper diagnostic
description.
COOLING
HEATING
MIN (°F)
MAX (°F)
MIN (°F)
MAX (°F)
60
115
-10
70
Table 2. Heat Pump Operating Temperatures
STATUS
INDICATOR
STATUS
TYPE
DIAGNOSTIC
DESCRIPTION
C1
H1
Operating Status
Operating Status
Cooling, 1st Stage
Heating, 1st Stage
SC
Operating Status
Anti Short Cycle Timer
OF
Operating Status
Defrost
_.
Operating Status
Power on, no call
for operation
01
Fault
Pressure switch, low
02
Fault
03
Fault
Pressure switch, high
Temperature Sensor,
Ambient
Temperature Sensor, Coil
04
Fault
05
Fault
OF
(FLASHING)
Input Error
Board
Forced defrost - test short
applied longer than 11
minutes
Table 3. Defrost Control Board Status Indicators
7
HEAT PUMP MAINTENANCE
WARNING:
To prevent electrical shock, personal injury, or
death, disconnect all electrical power to the unit
before performing any maintenance or service.
The unit may have more than one electrical
supply.
Proper maintenance is important to achieve optimum
performance from the heat pump. The ability to properly
perform maintenance on this equipment requires certain
mechanical skills and tools. If you do not possess these
skills, contact your dealer for maintenance. Consult your
local dealer about the availability of maintenance contracts.
Routine maintenance should include the following:
• Inspect and clean or replace air filters at the beginning
of each heating and cooling season, or more frequently
if required.
• Inspect the outdoor coil at the beginning of each cooling
season. Remove any debris. Clean the outdoor coil and
louvers as necessary using a mild detergent and water.
Rinse thoroughly with water.
• Inspect the electrical connections for tightness at the
beginning of each heating and cooling season. Service
as necessary.
Figure 6. Panel Removal
DETAIL A
CAUTION:
The unit should never be operated without a
filter in the return air system. Replace disposable
filters with the same type and size.
DETAIL B
• Do not add additional oil to motors unequipped with oil
tubes. The compressor is hermetically sealed at the factory
and does not require lubrication.
• To access the internal components of the unit, refer
to Figure 6 for panel removal and Figure 7 for panel
installation.
Panel Removal
1. Remove screws securing the panel.
2. Slide the panel up towards the top pan in order to clear
the bottom flange from the base pan. See Figure 6 (page
8).
3. Swing the bottom of the panel out and pull the panel down
to remove it from the unit.
Panel Installation
1. Insert the top corners of side panel flanges into the corner
post channels as shown in Detail A in Figure 7 (page 8).
2. Slide the panel up into the top pan. (You may need to push
on the center of the panel at the top in order to clear the
top pan edge).
3. Swing the panel in and push down until the panel is resting
on the top edge of the base pan wall as shown in Detail
B.
4. Insert screws into the panel to secure it to the unit.
8
Figure 7. Panel Installation
REFRIGERANT CHARGING
WARNING:
This split system heat pump is shipped charged
with R410A refrigerant and ready for installation.
If repairs make it necessary for evacuation and
charging, it should only be attempted by qualified
trained personnel thoroughly familiar with this
equipment. Under no circumstances should
the owner attempt to install and/or service this
equipment. Failure to comply with this warning
could result in property damage, personal injury,
or death.
After refrigerant line connections are completed, it is required
that you leak check and evacuate the indoor section and all
line connections (using proper methods) before finalizing
the full system refrigerant charge.
• To achieve rated capacity and efficiency, the compressor
must be exposed to refrigerant for at least 24 hours prior
to running and then the compressor must be run for a
minimum of 12 hours.
• Refer to the Quick Reference Data sheet for additional
charging information. Outdoor units with non-AHRI listed
indoor coils are not recommended and deviations from
rated airflows or non-listed combinations may require
modification to the expansion device and refrigerant
charging procedures for proper and efficient system
operation.
• The refrigerant charge can be checked and adjusted
through the service ports provided external to the outdoor
unit. Use only gage line sets which have a “Schrader”
depression device present to actuate the valve. A common
suction port for heating mode charging is included and
located on the compressor access panel above the outdoor
unit service valves.
• A high-pressure switch is factory-installed and located in
the compressor discharge line internal to the outdoor unit.
The switch is designed to de-energize the system when
very high pressures occur during abnormal conditions.
Under normal conditions, the switch is closed. If the
discharge pressure rises above 575 psig, then the switch
will open and de-energize the outdoor unit. The switch will
close again once the liquid pressure decreases to 460
psig. Please note that the switch interrupts the thermostat
inputs to the unit. When the switch opens and then closes,
there will be a 5 minute short cycling delay before the
outdoor unit will energize.
• A low-pressure switch is factory installed (certain models)
and located internally on the suction line of the outdoor unit.
The switch is designed to protect the compressor from a
loss of charge by interrupting the thermostat inputs to the
unit. If the suction pressure falls below 20 psig, the switch
will open and de-energize the outdoor unit. The switch will
close again when the suction pressure increases above
35 psig. When the switch opens and then closes, there is
a 3 minute short cycling delay before the outdoor unit will
energize. Under normal conditions the switch is closed.
Charging the Unit in AC mode
If the outdoor temperature is 65 degrees F or higher:
After completing the refrigerant line connections, leak
checking the system, and evacuating the indoor section
and all line connections (using proper methods), perform
the following steps:
1. Determine the recommended charge addition (if applicable)
for the system being installed. This information is in the
unit’s QRD (Quick Reference Data sheet).
2. Calculate the amount of additional refrigerant needed for
the line set length of the actual installation. This information
is on the first page of the unit’s QRD (Quick Reference
Data sheet).
3. Weigh in the additional charge amounts determined by
step 1 and 2 above.
4. Adjust the charge to match the superheat (for fixed orifice
systems) or subcooling (for TXV systems). There are three
different resources for doing this:
a.) The chargecalculator.com website. This will walk
you through the charging process step by step.
b.) The charging tables on the inside of the outdoor
unit’s electrical box cover panel. These tables
provide superheat targets for fixed orifice systems
and subcooling targets for TXV systems. The system
should be charged so that the measured superheat/
subcooling are within 1 degree F of the target listed
in the table.
For fixed orifice systems:
• If your measured superheat at the suction valve is
LESS THAN the recommended superheat value
in the table then REMOVE refrigerant.
• If your measured superheat at the suction valve
is GREATER THAN the recommended superheat
value in the table then ADD refrigerant.
For TXV systems:
• If your measured subcooling at the liquid valve is
LESS THAN the recommended subcooling value
in the table then ADD refrigerant.
• If your measured subcooling at the liquid valve is
GREATER THAN the recommended subcooling
value in the table then REMOVE refrigerant.
c.) The charging tables in the Supplemental Charging
Information, can be found online in the literature
library. The tables can also be accessed by scanning
the QR code on the unit’s electrical panel. The
pressures listed in these tables are for reference only
and are to be used in troubleshooting a system. The
system should be charged to match the superheat
or subcooling targets as previously noted and not
to match the system pressures. Follow the same
procedure described in 4b above.
If the outdoor temperature is between 35 degrees F and
65 degrees F:
After completing the refrigerant line connections, leak
checking the system, and evacuating the indoor section
and all line connections (using proper methods), perform
the following steps:
1. Determine the recommended charge addition (if applicable)
for the system being installed. This information is in the
unit’s QRD (Quick Reference Data sheet).
2. Calculate the amount of additional refrigerant needed for
the line set length of the actual installation. This information
9
superheat/subcooling are within 1 degree F of the
target listed in the table.
For fixed orifice systems:
• If your measured superheat at the suction valve is
LESS THAN the recommended superheat value
in the table then REMOVE refrigerant.
• If your measured superheat at the suction valve
is GREATER THAN the recommended superheat
value in the table then ADD refrigerant.
For TXV systems:
NOTE: One half of the unit should be covered corner to corner.
Figure 8. Blocked Off Outdoor Fan Discharge
is on the first page of the unit’s QRD (Quick Reference
Data sheet).
3. Weigh in the additional charge amounts determined by
step 1 and 2 above.
4. Block off the discharge of the outdoor fan. NOTE: One half
of the unit should be covered corner to corner as shown
in Figure 8 (page 10).
5. With the unit in cooling mode, Adjust the charge to match
the superheat (for fixed orifice systems) or subcooling (for
TXV systems). There are two different resources for doing
this:
a.) The chargecalculator.com website. This will walk
you through the charging process step by step.
b.) The low ambient charging tables on the inside of
the outdoor unit’s electrical box cover panel. These
tables provide superheat targets for fixed orifice
systems and subcooling targets for TXV systems.
The system should be charged so that the measured
10
• If your measured subcooling at the liquid valve is
LESS THAN the recommended subcooling value
in the table then ADD refrigerant.
• If your measured subcooling at the liquid valve is
GREATER THAN the recommended subcooling
value in the table then REMOVE refrigerant
If the outdoor temperature is below 35 degrees F:
After completing the refrigerant line connections, leak
checking the system, and evacuating the indoor section
and all line connections (using proper methods), perform
the following steps:
1. Determine the recommended charge addition (if applicable)
for the system being installed. This information is in the
unit’s QRD (Quick Reference Data sheet).
2. Calculate the amount of additional refrigerant needed for
the line set length of the actual installation. This information
is on the first page of the unit’s QRD (Quick Reference
Data sheet).
3. Weigh in the additional charge amounts determined by
steps 1 and 2 above.
4. Return to the system when the outdoor temperature is 35
degrees F or higher and follow the steps defined in step 4
of the “If the outdoor temperature is between 35 degrees
and 65 degrees F" or "If the outdoor temperature is 65
degree F or higher” sections above as applicable.
YELLOW
C
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
HPS
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
(24V COM)
Y1 OUT
Y2 OUT
HOT1
HOT2
COIL#1
TEMP
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
LPS - Low Pressure Switch
RVS - Reversing Valve Solenoid
* HARD START KIT (OPTIONAL)
HGBP
COIL SENSOR
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
CCH
T2
L2
CAPACITOR
F
(OPTIONAL
OUTDOOR
THERMOSTAT)
RVS
LPS
HGBP
HPS
COIL SENSOR
Y
O
C W2
C W2 IN
E
ODT
Y2 IN
BLACK
THERMOSTAT
R
Y1 IN R O
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
FAN1 FAN2 CCH2 CCH1
TEMP
DEFROST CONTROL
BOARD
AMB SENSOR
5
BLACK
BLACK
BLACK
BLACK
BLACK
H
C
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
04/16
711316C
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
(OPTIONAL OUTDOOR
THERMOSTAT)
RVS
LPS
2
YELLOW
CC
R
DEFROST CONTROL BOARD
AMB SENSOR
C
F
DUAL CAPACITOR
H
S
T1
L1
NOTES:
1. Disconnect all power before servicing.
1. Couper le courant avant de faire letretien.
2. For supply connections use copper conductors only.
2. Employez uniquement des conducteurs en cuivre.
3. Not suitable on systems that exceed 150 volts to ground
3. Ne convient pas aux installations de plus de 150 volt a la terre.
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
WIRING DIAGRAMS
CC
Figure 9. Wiring Diagram for *SH(1,2)BE4M1SP with Low Pressure Switch
11
12
YELLOW
R
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
C
HPS
LPS
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
(OPTIONAL
OUTDOOR
THERMOSTAT)
RVS
HGBP
HPS
COIL SENSOR
5
LPS
BLACK
Y
W2 E
THERMOSTAT
R O C
Y1 IN R O C W2 IN
RVS
R C Y P
CORESENSE
BLACK
BLACK
BLACK
2
CAPACITOR
F
BLACK
CCH
H
C
L1
T1
L2
R
S
GRD
Figure 10. Wiring Diagram for *SH1BE4M1SP with CoreSenseTM and Low Pressure Switch
01/19
10252930
(Replaces 711341C)
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
BLACK
(OPTIONAL OUTDOOR
THERMOSTAT)
RED
YELLOW
ODT
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
TEMP FAN1 FAN2 CCH2CCH1
DEFROST CONTROL
BOARD
AMB SENSOR
BLACK
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
* HARD START KIT (OPTIONAL)
LPS - Low Pressure Switch
CC
R C Y P
COIL SENSOR
CORESENSE
HGBP
CCH
T2
L2
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
DEFROST CONTROL BOARD
AMB SENSOR
C
F
DUAL CAPACITOR
H
S
T1
L1
NOTES:
1. Couper le courant avant de faire letretien.
1. Disconnect all power before servicing.
2. Employez uniquement des conducteurs en cuivre.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground
3. Ne convient pas aux installations de plus de 150 volt a la terre.
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
YELLOW
C
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
HPS
LPS
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
CCH
T2
L2
RVS
HGBP
HPS
COIL SENSOR
5
Y
W2
BROWN
THERMOSTAT
R O C
Y1 IN R O C W2 IN
E
ODT
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT LPS
OUTDOOR
TEMP FAN1 FAN2 CCH2CCH1
DEFROST CONTROL
BOARD
AMB SENSOR
BLACK
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
ODT - Outdoor Thermostat
* HARD START KIT (OPTIONAL)
LPS -Low Pressure Switch
HGBP
COIL SENSOR
CC
R
DEFROST CONTROL BOARD
AMB SENSOR
C
F
DUAL CAPACITOR
H
S
T1
L1
CAPACITOR
F
BLACK
BLACK
BLACK
BLACK
BLACK
BROWN
RVS
2
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
01/19
10252920
(New)
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
H
C
NOTES:
1. Disconnect all power before servicing.
1. Couper le courant avant de faire letretien.
2. Employez uniquement des conducteurs en cuivre.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground
3. Ne convient pas aux installations de plus de 150 volt a la terre.
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
Figure 11. Wiring Diagram for *SH1BE4M1SP with Low Pressure Switch (Manufactured Housing)
13
14
YELLOW
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
C
HPS
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
CCH
T2
L2
RVS
HGBP
HPS
COIL SENSOR
5
Y
Figure 12. Wiring Diagram for *SH2BE4M1RP (Manufactured Housing)
W2
THERMOSTAT
R O C
Y1 IN R O C W2 IN
E
ODT
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
TEMP FAN1 FAN2 CCH2CCH1
DEFROST CONTROL
BOARD
AMB SENSOR
BLACK
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
* HARD START KIT (OPTIONAL)
HGBP
COIL SENSOR
AMB SENSOR
CC
S
R
DEFROST CONTROL BOARD
C
F
H
DUAL
CAPACITOR
PTCR
T1
L1
CAPACITOR
F
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BROWN
PTCR
RVS
2
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
10/18
10252180
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
H
C
NOTES:
1. Couper le courant avant de faire letretien.
1. Disconnect all power before servicing.
2. Employez uniquement des conducteurs en cuivre.
2. For supply connections use copper conductors only.
3. Not suitable on systems that exceed 150 volts to ground
3. Ne convient pas aux installations de plus de 150 volt a la terre.
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
YELLOW
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
C
HPS
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
CCH
T2
L2
RVS
HGBP
HPS
COIL SENSOR
5
Y
W2
BROWN
THERMOSTAT
R O C
Y1 IN R O C W2 IN
E
ODT
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
TEMP FAN1 FAN2 CCH2CCH1
DEFROST CONTROL
BOARD
AMB SENSOR
BLACK
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
ODT - Outdoor Thermostat
* HARD START KIT (OPTIONAL)
HGBP
COIL SENSOR
CC
R
DEFROST CONTROL BOARD
AMB SENSOR
C
F
DUAL CAPACITOR
H
S
T1
L1
CAPACITOR
F
BLACK
BLACK
BLACK
BLACK
BLACK
BROWN
RVS
2
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
03/18
10214360
(New)
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
H
C
NOTES:
1. Couper le courant avant de faire letretien.
1. Disconnect all power before servicing.
2. Employez uniquement des conducteurs en cuivre.
2. For supply connections use copper conductors only.
3. Ne convient pas aux installations de plus de 150 volt a la terre.
3. Not suitable on systems that exceed 150 volts to ground
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
Figure 13. Wiring Diagram for *SH2BE4M1SP (Manufactured Housing)
15
16
YELLOW
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
C
HPS
Figure 14. Wiring Diagram for *SH2BE4M1RP (Builder's Series)
Y
E
THERMOSTAT
R O C
W2
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
CCH
T2
L2
RVS
HGBP
HPS
COIL SENSOR
5
Y
E
THERMOSTAT
R O C
Y1 IN R O C W2 IN
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
TEMP FAN1 FAN2 CCH2CCH1
DEFROST CONTROL
BOARD
AMB SENSOR
W2
BLACK
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
* HARD START KIT (OPTIONAL)
HGBP
COIL SENSOR
AMB SENSOR
CC
S
R
DEFROST CONTROL BOARD
C
F
H
DUAL
CAPACITOR
PTCR
T1
L1
CAPACITOR
F
PTCR
RVS
2
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
BLACK
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
12/14
10066150
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
H
C
NOTES:
1. Couper le courant avant de faire letretien.
1. Disconnect all power before servicing.
2. Employez uniquement des conducteurs en cuivre.
2. For supply connections use copper conductors only.
3. Ne convient pas aux installations de plus de 150 volt a la terre.
3. Not suitable on systems that exceed 150 volts to ground
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
YELLOW
R
C
OUTDOOR FAN MOTOR
S
COMPRESSOR
C
HPS
CCH
T2
L2
Y
W2
THERMOSTAT
R O C
E
ODT
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
Y2 IN
Y1 IN R O C W2 IN
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
COIL#1
TEMP
RVS
HGBP
HPS
COIL SENSOR
(OPTIONAL
OUTDOOR
THERMOSTAT)
OUTDOOR
TEMP FAN1 FAN2 CCH2 CCH1
AMB SENSOR - Ambient Sensor
CC - Contactor Coil
CCH - Crankcase Heater
HPS - High Pressure Switch
HGBP - Hot Gas By Pass Valve
RVS - Reversing Valve Solenoid
* HARD START KIT (OPTIONAL)
HGBP
COIL SENSOR
CC
R
DEFROST CONTROL BOARD
AMB SENSOR
C
F
DUAL CAPACITOR
H
S
T1
L1
CAPACITOR
F
Y
O
C
W2
C W2 IN
THERMOSTAT
R
Y1 IN R O
E
ODT
Y2 IN
HP2 HP1 LP2 LP1 W2 OUT RV2 RV1
COIL#1
TEMP
HOT1
HOT2
(24V COM)
Y1 OUT
Y2 OUT
OUTDOOR
FAN1 FAN2 CCH2 CCH1
TEMP
DEFROST CONTROL
BOARD
AMB SENSOR
5
BLACK
BLACK
BLACK
BLACK
BLACK
H
C
L1
T1
L2
R
S
GRD
GROUNDING
SCREW
C
COMPRESSOR
R
BLACK
04/16
711315C
BLACK/
BLACK WHITE
YELLOW/
YELLOW BLACK
S
C
OUTDOOR
FAN MOTOR
Single Phase
RED/RED BLACK
BLUE
(SINGLE PHASE)
FIELD SUPPLY
L1
L2
T2
ORANGE
CONTACTOR
CC
BLACK
CCH
(OPTIONAL OUTDOOR
THERMOSTAT)
RVS
2
NOTES:
1. Disconnect all power before servicing.
1. Couper le courant avant de faire letretien.
2. For supply connections use copper conductors only.
2. Employez uniquement des conducteurs en cuivre.
3. Ne convient pas aux installations de plus de 150 volt a la terre.
3. Not suitable on systems that exceed 150 volts to ground
4. For replacement wires use conductors suitable for 105˚ C.
5. For ampacities and overcurrent protection, see unit rating plate.
START RELAY*
6. Connect to 24 vac/40va/class 2 circuit. See furnace/air handler
START
LEGEND:
installation instructions for control circuit and optional
CAPACITOR*
1
FIELD WIRING
relay/transformer kits.
LOW VOLTAGE
DUAL
208/230V
HIGH VOLTAGE
Split System Heat Pump (Outdoor Section)
WIRING DIAGRAM
YELLOW
CC
BLACK
Figure 15. Wiring Diagram for *SH2BE4M1SP (Builder's Series)
17
18
19
INSTALLATION CHECKLIST
ELECTRICAL SYSTEM
INSTALLATION ADDRESS:
CITY:
STATE:
Electrical connections tight?
YES
NO
Line voltage polarity correct?
YES
NO
UNIT MODEL #:
Rated Voltage:
UNIT SERIAL #:
Has the thermostat been calibrated?
YES
NO
Is the thermostat level?
YES
NO
Is the heat anticipator setting correct?
(If Applicable)
YES
NO
Unit Installed Minimum clearances
per Figure 1 (page 3)?
YES
NO
INSTALLER NAME:
CITY:
REPLACEMENT PARTS
STATE:
Has the owner’s information been
reviewed with the customer?
YES
NO
Has the Literature Package been left
with the unit?
YES
NO
Replacement parts are available through your distributor.
Please have the complete model and serial number of the
unit when ordering replacement parts.
Capacitors
REFRIGERATION SYSTEM
Was unit given 24 hr warm up period
for crankcase heaters?
YES
NO
Compressors
Thermostats
Contactors
Time Delay Relays
Pressure Switches
Transformers
Relays
Stage-1 Liquid Pressure (High Side):
Stage-1 Suction Pressure (Low Side):
ELECTRICAL:
Temperature Limit Switches
Blower Motor
Fan Motor
Blower Assembly
Cabinet Panels
MOTORS:
COMPONENTS:
Fan Grille
Filter/Driers
Expansion Valves
Specifications & illustrations subject to change without notice or incurring obligations (12/18).
O’Fallon, MO, © Nortek Global HVAC LLC 2018. All Rights Reserved.
10252480
(Replaces 1016544A)
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement