Frigidaire PL36DD50EC Installation guide

Frigidaire PL36DD50EC Installation guide
MODELSPL30DD& PL36DD
DOWNDRAFTBLOWERSYSTEM
INTENDED FOR DOMESTIC COOKHNG ONLY
TO REDUCE
THE RISK OF FmRE, ELECTRIC
SHOCK,
INJURY TO PERSONS,
OBSERVE
THE FOLLOWmNG:
1.
2.
3.
Use this unit only in the manner intended by the manufacturer.
If you have questions, contact the manufacturer
at the address
or telephone
number in the warranty.
TO REDUCE
THE RISK OF INJURY
EVENT OF A RANGE
TOP GREASE
FOLLOWINGa:
Before servicing or cleaning unit, switch power off at service
panel and lock the service disconnecting
means to prevent
power from being switched on accidentally.
When the service
disconnecting
means cannot
be locked, securely
fasten a
prominent warning device, such as a tag, to the service panel.
Installation
work and electrical
wiring must be done by a
qualified
person(s)
in accordance
with all applicable
codes
and standards,
standards.
4.
OR
including
fire-rated
construction
codes
1.
SMOTHER
FLAMES with a close-fitting
lid, cookie sheet,
or metal tray, then turn off the burner. BE CAREFUL
TO
PREVENT
BURNS.
If the flames do not go out immedi
ately, EVACUATE
AND CALL THE FIRE DEPARTMENT.
2.
NEVER
3.
DO NOT USE WATER, including wet dishcloths
- a violent steam explosion will result.
4.
Use an extinguisher
PICK UPA
FLAMING
ONLY
PAN -You
may be burned.
or towels
if:
A. You know you have a Class ABC extinguisher,
and you
already know how to operate it.
B. The fire is small and contained
in the area where it
started.
and
Sufficient air is needed for proper combustion
and exhausting
of gases through the flue (chimney) of fue! burning equipment
to prevent
backdrafting.
Follow
the heating
equipment
manufacturer's
guideline and safety standards such as those
published by the National Fire Protection Association
(NFPA),
TO PERSONS
IN THE
F_RE, OBSERVE
THE
C. The fire department
is being
called.
D. You can fight the fire with your
a Based
on "Kitchen
Firesafety
Tips"
back to an exit.
published
by NFPA.
and the American
Society for Heating, Refrigeration
and Air
Conditioning
Engineers
(ASHRAE),
and the local code authorities.
1.
5.
When cutting or drilling into wall
electrical wiring and other hidden
For general
ventilating
hazardous
or explosive
2.
6.
Do not use this range
device.
To avoid motor bearing damage and noisy and/or unbalanced
impellers, keep drywall spray, construction
dust, etc. off power
unit.
7.
Ducted
3.
Clean
4.
Do not repair or replace any part of this appliance
unless
specifically
recommended
in this manual. All other servicing
should be done by a qualified technician.
5.
Please read specification
tion and requirements.
or ceiling,
utilities.
do not damage
hood with an additional
fans must always
be vented
speed
control
to the outdoors.
8.
To reduce
9.
Do not instal! this product with the activating
switch directly
behind a burner or element.
Minimum
distance between the
switch
the risk of fire, use only metal ductwork.
and the edge of the burner
10. Loose-fitting
or hanging clothing
operating
this appliance.
They
elements
11. Children
where
be 4 inches.
should never be worn when
may be ignited by burners/
on cooktop.
should not be left alone
this appliance
should
or unattended
in the area
is in use.
12. When flaming foods, turn the blower
may spread the flames.
OFF. An operating
blower
13. This unit must be grounded.
TO REDUCE
THE
RmSK OF A RANGE
TOP GREASE
FIRE:
1.
Never leave surface units unattended at high settings. Boilovers
cause smoking
and greasy spillovers
that may ignite. Heat
oils slowly on low or medium settings.
2.
Always
cooking
3.
Clean ventilating fans frequently
to accumulate
on fan or filter.
4.
Use proper pan size. Always
use cookware
the size of the surface element.
turn hood ON when
flaming foods.
cooking
Grease
at high
sh°uld
filters
and greaseqaden
for further
informa-
TYPICAL
COUNTER
TOP
INSTALLATION
CHIMNEY
TOP
COOK TOP
This unit can be easily installed
following these basic steps:
Mount the unit in the
cabinet.
Connect the ductwork
and electrical.
L
/
/
Install the cooktop.
INSTALLER:
frequently.
cooking with a variety of gas or
electric
cooktops.
It can be
mounted
in island, peninsula,
or
conventional
wall locations.
n°t be all°wed
for
label on product
This downdraft
blower system is
designed
to be used to exhaust
airborne
contaminants
when
Cut out the countertop
opening.
appropriate
surfaces
to exhaust
PLANNING
or when
heat
use only. Do not use
materials and vapors.
Save this manual for Electrical Inspector
HOMEOWNER:
Use and Care Information
3-1/4" x 10"
DUCT CONNECTOR
and Homeowner
on Page 5.
to use.
PLANNING
-(continued)
PLAN THE DUCTWORK
Note: The high level of air flow of this appliance
may affect the gas
flame on some types of gas cooktops.
This is NORMAL and wil!
cause no harm, but can be corrected by lowering the speed of the
blower.
RIGHT
DISCHARGE
LEFT
DISCHARGE
,_.
DOWN
DISCHARGE
(as shipped)
This downdraft
blower system is designed for use with 3-1/4"
x 10" ductwork
(can be transitioned
to 6" round).
Three
different
discharge
directions
are available with side-to-side
adjustment
for accurate alignment
of ductwork.
2.
TAKE MEASUREMENTS
1.
2.
Refer to the cooktop installation
instructions
for dimensions
of
cooktop,
countertop
cut-out, and cabinet
requirements.
The
Model PL30DD will fit in most 30" wide cabinets and the Model
PL36DD
will fit in most 36" wide cabinets.
However,
it is
recommended
that oversized cabinets be used for easier installation.
Cooktop
cause
depth
can vary greatly
the fit of these
from one to another.
two appliances
For best performance:
Choose the ducting option which allows
the shortest
length of ductwork
and a minimum
number of
elbows and transitions.
Check location of floor joists, wall
studs, electrical wiring or plumbing
for possible interference.
NOTE: The unit is shipped with the 3-1/4" x 10" discharge
facing DOWN. See "CHANGING
BLOWER
DIRECTION"
on
page 3, if necessary.
6"ROUND
13-1_4"
X 10"
This may
to be rather tight.
_EQUALS 2 L
_EQUALS6 FT OF
[STRAIGHTDUCT
3-14" X 10"
qp_
L
IJ
HFT OF
BSTRA_GHT
DUCT
3.
The system will operate most efficiently
when
does not exceed 40 feet of equivalent
duct. The
shows equivalent
feet of elbows and transitions.
of feet of straight duct plus the equivalent
feet
and/or elbows to be used should equal 40 feet
the ductwork
chart, above,
The number
of transitions
or less.
NOTI=: The equivalent
feet of various
roof and wan caps has
been taken into consideration.
Do not include
them in this
calculation.
Pay special attention to the areas of potential interference
highlighted above. A countertop
with (A) a raised lip and/or (B) a
backsplash
may not allow enough flat countertop
for a proper
installation.
Note that 2" of flat countertop
is required
behind
cooktop and that 1-3/4" is necessary between the back edge of the
cooktop and the inside of cabinet back.
PLAN THE WIRING
1.
The downdraft
blower system
120 VAC, 60 Hz circuit.
draws
4 AMPS
and requires
a
2.
The unit has a 2 ft. long power cord with a 3-pronged plug. Plan
to provide a grounded
outlet in a location which will allow the
unit's power cord to reach. (Note: If the Mode! PL30DD is being
installed in a 30" wide cabinet or the Model PL36DD is being
installed in a 36" wide cabinet, the outlet cannot be located on
the back wall of cabinet.) Outlet may also be wal!-mounted,
with access hole in cabinet.
CUT COUNTER, TOP OPENMNG
CHANGING
The blower
these steps
BLOWER
is shipped
ONLY if:
Dm$CHARGE (Optionam)
with its discharge
facing
DOWN.
Follow
1.
Lay out and cut the cooktop cut-out
downdraft
will fit behind it.
2.
Set cooktop
Center
in place
and square
far enough
FORWARD
and slide
it as far forward
it with edges
of countertop.
so
as possible.
,, the position of the blower discharge
needs to be moved
so ductwork does not interfere with floor joists, plumb
ing or wiring below.
,, it is necessary
to rotate
RIGHT or LEFT.
Place
DOWN
the blower
discharge
the unit on its back on a table or work
DISCHARGE
o MOVING
to the
surface.
BLOWER
LEFT OR R_GHT
SHEET
BLOWER
NUTS
METAL_
SCREW
CLAMP
CHANNEL_,\
3.
Place
the
plastic
template
cooktop
and center
downdraft
opening.
BOTTOM
FLANGE
1.
Loosen
the 4 nuts and 2 clamp
2.
Slide blower
3.
Use supplied
4.
Tighten
screws
to desired
cover
4.
Remove
cooktop
5.
Cut downdraft
countertop.
back
template
flange
of the
to mark
the
opening.
Be
careful
not
to
chip
edges
of
channels.
position.
plate to close
open space
wing nuts to secure top of blower
through bottom flange to secure
OR RIGHT
the
around
from countertop.
(if any).
MOUNT THE UNiT
and use sheet metal
bottom of blower.
MOUNTING
LEFT
against
it. Trace
SCREWS
LEVELING BRACKET FLANGE FACING OUT
DISCHARGE
NUT
LEVELING
BRACKET
FLANGE FACING IN
Set downdraft
1.
Remove
2.
Carefully
the 4 nuts and 2 clamp
and disconnect
blower
and RECONNECT
3.
Use supplied
4.
Replace clamp channels
its new position.
5.
Use sheet
bottom
channels.
lift blower
Reposition
cover
metal
of blower.
plate to close
screws
motor
plug if necessary.
MOTOR
open space
and use nuts to secure
through
bottom
PLUG.
flange
Extend
leveling
brackets
to floor
2.
Secure the downdraft
to the countertop
as follows: Hold the
downdraft
against the back of countertop
cut-out and tightening the 2 mounting
screws (one on each end of unit) on
underside of countertop.
Use a wood shim between screw and
underside of granite countertops.
3.
Screw leveling brackets
holding leveling bracket
(if any).
the blower
into opening.
of cabinet so downdraft
sits straight. (Note: Leveling brackets
can be removed
and re-attached
in other positions.
Bottom
flange may have to face inward in tight cabinet installations.)
in
to secure
3
to bottom of cabinet. Tighten
to unit on each side.
screws
INSTALL DUCTWORK
WIRING DIAGRAM
120 VAC
CAUTBON
- BEFORE
CUTTING
WORK." Check for interference
cal wiring or plumbing.
HOLE IN CABINET
with floor joists,
FOR DUCT-
wal! studs,
MNE
_N
electri-
3-1/4" X 10"
TO 6" RD
TRANSmON
6" RD
ELBOW &
DUCT-
INSTALL COOKTOP
1. Align the cooktop
place.
with
the downdraft
Note: Accurate alignment of cooktop
to ensure that there is no interference
1.
Cut
hole
in cabinet
as we!l
as
holes
in wall
or floor
as
and fasten
cooktop
in
and downdraft is necessary
when air vent is raised and
lowered. There should be a gap of 1/32"-1/16"
of the cooktop and the front of the downdraft
between
cover.
the back
necessary.
2.
3.
Mount the roof or wall cap and work back towards the cabinet,
attaching
al! ductwork,
elbows and transitions
as previously
planned. Tape al! ductwork connections
to make them secure
and air tight.
Connect ductwork (and transition,
if required) to downdraft.
If
necessary,
LOOSEN
nuts and screws that hold the blower in
place, and slide blower left or right to meet ductwork.
Retighten screws and nuts.
ADJUSTMENT
The downdraft
is factory-adjusted
for proper operation.
However,
shipping
and handling
may affect the position of the activating
switch.
To adjust
position
of activating
switch:
Note: A 3-1/4" x 10" collar is provided for insta!lers who prefer to
rivet the ductwork to the unit. This will allow blower to be removed
and replaced
work.
easily
in service
situations
without
disturbing
duct-
INSTALL ELECTRICAL WIRING
1.
Mount a standard
inside the cabinet.
easily reach it.
1.
If downdraft
2.
Lift air vent straight
UP position.
wiring box, with %pronged
receptacle,
Make sure the downdraft's
power cord can
2.
Run appropriate
receptacle.
power
3.
Plug the downdraft's
cable
power
into cabinet
cord
and connect
is plugged
into electrical
outlet,
up and cock it slightly
unplug
it.
so it remains
in the
SWITCH
MEMBRANE
it to
into the outlet.
3.
Remove
switch
cover from right end of air vent.
4.
Loosen the 2 screws
Position switch bracket
contact with underside
5.
Replace switch cover, gently lower air vent into chimney, and
plug in power cord. Re-connect
electrical
power and check
operation.
holding the switch bracket
in place.
so that activating switch just comes in
of switch membrane.
Tighten screws.
USE AND CARE
USE AND CARE - JContinued}
Always turn the downdraft blower on before you begin cooking to
establish an air flow in the kitchen. Let the blower run for a few
minutes to clean the air after you turn the cooktop
keep the whole kitchen cleaner and brighter.
off. This will
WARNING:
power supplyA_ways
before disconnect
c_eaning
e_ectric
unit.
1
Use a mild detergent suitable for painted surfaces.
DO NOT USE
ABRASIVE
CLOTH,
STEEL
WOOL
PADS, OR SCOURING
POWDERS.
Vacuum blower to clean. Do not immerse blower in
water.
CONTROLS
Wash the 2 aluminum
grease filters in a mild detergent solution or
a dishwasher.
Remove them from the air vent by grasping the tab
at the top of each filter.
Note: The filters
removed,
(wider
Turn the downdraft blower ON by pressing
switch. The air vent will rise.
-%
are different
sizes. Be sure to replace
one on the left), with tabs UP.
them as
down on the activating
KNOB
SERViCiNG
WARNING:
A_ways
power supply before
The blower can be turned ON or OFF and its speed can be
adjusted with the recessed
knob on the right side of the air vent.
disconnect
e_ectric
servicing
unit.
It may be necessary to remove the [email protected]
the cabinet in order to service components
motor or air vent mechanism.
blower system from
such as the blower
Disconnect
power to the cooktop and remove it first. Reverse the
steps under "MOUNT
THE UNIT" to remove the downdraft
from
the cabinet.
Turn the downdraft blower OFF by pressing the activating switch
again. The air vent will go down and the blower will shut OFF.
Note: For most convenient
operation,
set the blower to your
favorite speed. The blower will come on to this speed whenever
the activating switch is pressed and the air vent rises.
1
1
SERVICE PARTS
Models PL30DD & PL36DD
Downdraft
Blower System
KEY NO.
1
2
3
4
5
6
7
8
9
10
11
12
16
17
18
19
2O
21
22
23
24
25
26
28
29
3O
31
32
33
45
46
47
49
5O
51
52
53
54
55
56
57
58
59
6O
61
62
64
65
66
67
68
7O
71
73
74
75
84
*Standard
**Service
DESCRIPTION
Bushing, 7/8"
Bushing, Split Heyco, 5/8"
Bushing, Heyco, 1/2"
Roller
Switch Assembly, Up/Down
Wire Harness, Speed Control
Nut, 3/8-32
Knob
Motor insolator
Lower Switch Bracket Assembly
Green Ground Wire
Wire Harness
Back-up Plate
Crank
Switch Cover
Chimney Assembly with Slide
Motor (with Capacitor-Key No. 73)
Blower Wheel
Scroll Box Extension
Spacer
Top Bracket Assembly, Right
Top Bracket Assembly, Left
Top, Stainless
Scroll Box Assembly
Gear Motor Cover
Air Box Assembly
Scroll Box Cover
Capacitor Strap
Filter Kit (contains 2 filters)
End Cap
Gearmotor
Slide Strip
Screw, #8-18 x .375 SLT HX WS HD
Screw, #10-32 x .500 HX WS BDRH
Screw, #8-18 x .375 SR PH TRH
Screw, #8-18 x .500 No. 5 PH Trim
Cover, Air Box Opening
Nut, #10-24
Air Box Cover
Gearmotor Bracket Assembly
Leg Support
Screw, 1/4-20 x 5/16
Washer, 1/4
Screw, #8-32 x 1/2 PH HD MS
Screw, #!0-24 x 3/8 SH WH LOCK
Screw, #10-24 x 3/8 PH FL HD LD
Nut, 10-24 HEX KEPS
Nut, 1/4-20 WHIZ LOCK
U-Bolt, 10-24
Strain Relief
Nut, Hex Flange
Wire Channel Clamp
Wire Tie
Capacitor
Screw, 1/4-20 x 1.250 HEX HD
#8-18 x .250 PH TR HD BPT
Seal - Foam
Blower Assembly, Complete (Includes Key Nos.2, 9,
20, 21,22, 28, 31, 32, 49, 58, 64, 65, & 73)
Chimney Assembly, Complete
(Includes Key Nos. 5, 8, 19, 45, 51,52, & 71)
Hardware
Assembly
o May be purchased
- Contains
numerous
Ioca!ly.
parts.
6
QTY.
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
1
1
1
4
19
2
6
2
1
4
1
1
2
5
2
4
1
1
7
3
1
1
1
2
3
1
2
2
1
OPTIONAL
MODEL
NO.
TOP
COVER
KITS
DESCRIPTION
HT2730B
30" Black
HT2736B
36" Black
HT2730W
30" White
HT2736W
36" White
SERVICE
PARTS
Models PL30DD & PL36DD
Downdraft
Blower System
/
51
\
84
Your appliance is covered by a one year limited warranty. For one year from your original date of purchase,
Electrolux will pay all costs for repairing or replacing any parts of this appliance that prove to be defective
in materials or workmanship when such appliance is installed, used, and maintained in accordance with the
provided instructions.
Exclusions
This warranty
does
not cover the following:
1.
Products
2.
Product that has been transferred
Canada.
with original
3.
Rust on the interior or exterior
4.
Products
5.
Food
6.
Products
7.
Service
purchased
serial numbers
"as-is"
are not covered
used in a commercial
calls which
calls to correct
or cannot
malfunction
use or used other
the installation
or defects
in materials
than in accordance
Expenses for making the appliance accessible for servicing, such as removal
which are not a part of the appliance when it is shipped from the factory.
10. Service calls to repair or replace
11. Surcharges
charges,
12. Damages
cabinets,
including,
or mileage
of your appliance
or workmanship,
with the provided
9.
cosmetic
appliance
or to instruct
or for appliances
instructions.
you how to use your appliance.
of trim, cupboards,
shelves,
light bulbs, air filters, water filters, other consumables,
etc.,
or knobs,
parts.
but not limited to, any after hour, weekend,
expense
the USA or
or freezer failures.
Service
or other
determined.
outside
by this warranty.
8.
handles,
be readily
party or removed
setting.
do not involve
household
altered
owner to another
of the unit.
loss due to any refrigerator
not in ordinary
that have been removed,
from its original
for service
to the finish of appliance
walls, etc.
calls to remote
or home incurred
or holiday
areas, including
during
installation,
service calls, tolls, ferry trip
the state of Alaska.
including
but not limited to floors,
13. Damages caused by: services performed by unauthorized service companies; use of parts other than genuine
Electrolux parts or parts obtained from persons other than authorized service companies; or external causes
such as abuse, misuse, inadequate power supply, accidents, fires, or acts of God.
DISCLAIMER
OF IMPLIED
WARRANTIES;
CUSTOMER'S
SOLE AND EXCLUSIVE
LIMITATION
REMEDY
OF REMEDIES
UNDER THIS LIMITED
WARRANTY
SHALL
BE PRODUCT
REPAIR OR REPLACEMENT
AS PROVIDED HEREIN. CLAIMS BASED ON IMPLIED WARRANTIES,
INCLUDING
WARRANTIES OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE
YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW, BUT NOT LESS THAN ONE YEAR. ELECTROLUX
SHALL NOT BE LIABLE FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES SUCH AS PROPERTY DAMAGE
AND INCIDENTAL EXPENSES RESULTING FROM ANY BREACH OF THIS WRITTEN LIMITED WARRANTY
OR ANY IMPLIED
WARRANTY.
SOME STATES AND PROVINCES
DO NOT ALLOW
THE EXCLUSION
OR
LIMITATION OF INCIDENTAL OR CONSEQUENTIAL
DAMAGES, OR LIMITATIONS ON THE DURATION OF
IMPLIED WARRANTIES, SO THESE LIMITATIONS OR EXCLUSIONS
MAY NOT APPLY TO YOU. THIS
WRITTEN WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS
THAT VARY FROM STATE TO STATE.
If You Need
Service
Keep your receipt,
delivery
should service be required.
Service under this warranty
slip, or some other
appropriate
payment
record
to establish
the warranty
period
If service is performed, it is in your best interest to obtain and keep all receipts.
must be obtained by contacting Electrolux at the addresses or phone numbers below.
This warranty only applies in the USA and Canada. In the USA, your appliance
is warranted by Electrolux Major Appliances
North
America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted
by Electrolux Canada Corp. Electrolux
authorizes no person to change or add to any obligations
under this warranty. Obligations for service and parts under this warranty
must be performed by Electrolux or an authorized
are subject to change without notice.
service
company.
Product
USA
1.800.944.9044
GA
or specifications
as described
or illustrated
Canada
1.800.668.4606
Electrolux
Major Appliances
North America
P.O. Box 212378
Augusta,
features
30907
Electrolux
Electrolux Canada Corp.
5855 Terry Fox Way
Mississauga,
Ontario, Canada
L5V 3E4
99043820A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement