Installation
Instructions
Advantium ®240V
Built-ln SpeedCook
Ovens
PSB2200
PSB2201
ZSC2200
ZSC2201
ZSC2202
49-40574-1
MFL06213302
02-08 JR
Safetg Information
BEFORE YOU BEGIN
Read these instructions
completely
CONTENTS
and carefully.
Design Information
Models Available ......................................................................
2
Product Dimensions and Clearances ............................
3
Tools and Parts Required ....................................................
3
Parts Supplied ..........................................................................
3
Electrical Tools and Parts Required ................................
3
Advance Planning ..................................................................
3
IM PORTANT- savethese
instructions
for
local inspector's
use.
IM PORTANT- Observe allgoverning codes
and ordinances.
• Note to Installer - Be sure to leave these
instructions with the Consumen
Installation
Preparation
Electrical Requirements ........................................................
/4
Install Junction Box ................................................................
/4
Preparing the Opening (Installation without
an accessorg storage drawer) ..................................
5%
Preparing the Opening (Installation with
an accessorg storage drawer) ..................................
7-8
• Note to Consumer
- Keep these instructions
with gour Owner's Hanual for future reference.
• Skill Level - Installation of this appliance
requires basic mechanical and electrical skills.
• Completion
Installation
Instructions
Step 1, Remove Packaging and Parts ..........................
9
Step 2, Route Conduit ........................................................
10
Step 3, Install Bottom Trim ..............................................
11
Step/4, Install Mounting Screws ....................................
11
Step 5, Finalize Installation ..............................................
11
Time - 1 Hour.
• Proper installation is the responsibilitg of the
installer. Product failure due to improper
installation is not covered under the warrantg.
See Owner's Manual for warrantg information.
IMPORTANT-
Use this oven onlg for
its intended purpose. Never use the oven for
warming or heating a room. Prolonged use of the
oven without proper ventilation can be hazardous.
MODELS AVAILABLE
Profile Models:
PSB2200NWW-White
CAUTION:
PSB2200NBB-Black
PSB2201NSS-Stainless Steel
For personal safety, remove house fuse or oven
circuit breaker before beginning installation to
avoid severe or fatal shock injurg.
Monogram Models:
ZSC2200NWW-White
ZSC2200NBB-Block
CAUTION:
For personal safetg, the mounting surface must
be capable of supporting the cabinet load, in
addition to the added weight of the 80-pound oven
and 30-pound drawer, plus additional oven loads of
up to 50 pounds or a total weight of up to 160
pounds.
ZSC2201NSS-Stainless Steel
Monogram Pro Range Models:
ZSC2202NSS-Stainless Steel
NOTE: This unit cannot be installed with an
accessorg storage drawer.
CAUTION:
For personalsafetg, this product cannot be
installed in cabinet arrangements such as an
island, a peninsula or below a countertop.
2
Design Information
PRODUCT DIMENSIONS
AND CLEARANCES
NOTE: Appearance
will vary by model.
_21-1/2"_
29-3/4"
[
"1
O
11
\
\
\
J
\
Yy
19"
,,
TOOLS
AND
PARTS
ADVANCEPLANNING
REQUIRED
(NOT SUPPLIED}
• These ovens may be installed directly into a 30" wide
oven cabinet.
[] #2 Phillips screwdriver
[] Hand held drill
[]
[]
[]
[]
• Cutout dimensions are NOT the same for installation
with or without an accessory storage drawer. Hake
sure to use the correct cutout when preparing the
opening.
NOTE: Model ZSC2202 CANNOT be installed with an
High speed drill bit, 3/32"diameter
3/8" slot head screwdriver
Level
Saw
accessory storage drawer See Installation
Preparation Without an Accessory Storage Drawer
for this model.
[] 2x_ or 2x2 lumber for installing runners
or 3/8" plywood for floor (if required)
[] Wood screws or other hardware for installing
runner or shelf to support oven (if required)
[] Safety glasses or goggles
IM PORTANT-This oven
is not approved for
use above another built-in Advantium Speedcook
oven, a side by side installation or below a
countertop.
• For personal safety, this oven cannot be installed
in a cabinet arrangement
such as an island or
peninsula.
• The oven must be installed at least 36-3//4" above
the floor.
PARTS SUPPLIED
[] 6 brass screws (3 required, 3 extra)
[] 5 color matched screws (4 required, 1 extra)
[] Bottom trim
• Allow for clearance to adjacent
drawers, etc.
ELECTRICAL
TOOLS
AND
• Cabinets installed adjacent to wall ovens must
have an adhesion spec of at least 194°F
temperature rating.
PARTS
REQUIRED (NOT SUPPLIED)
[] Junction box
[] Electrical cable (3-conductor
as required by local codes)
[] UL-listed conduit connectors
or t-conductor
corners, walls,
The oven must be securely installed in a cabinet
that is firmly attached to the house structure.
Weight on the oven door could cause the oven
to tip and result in injury. Never allow anyone to
climb, sit, stand or hang on the oven door.
wire
[] Wire cutters and wire strippers
If installing the drawer accessory, the drawer must
be assembled to the oven prior to installation into
the cabinet. See the Accessor_l Storage Drawer
Assemblg Instructions.
3
Installation
Preparation
ELECTRICALREQUIREMENTS
INSTALLJUNCTION BOX
Single Speedcook
The conduit is located at the top right on the back of
the oven.
Installation
Product rating is 120/208 or 120/240 volt, 60 Hz,
30 amps. This product must be connected to a supply
circuit of the proper voltage and frequency and
protected by a time delay fuse or circuit breaker.
Power should be supplied from a separate, dedicated
30-ampere branch circuit. Wire size must conform to
the requirements of the National Electrical Code or the
prevailing local code.
Combined
Speedcook
Locate and install thejunction
oven conduit.
• Through the left or right sides of the cabinet wall
and into adjacent cabinet.
• Or, through the cutout floor.
• Or, in the upper cabinet.
and Wall Oven Installation
When installed in combination with a GE/Honogram
single wall oven, use separate electrical junction boxes.
1-
Refer to single oven installation instructions for
electrical requirements of that product.
Cutout
Height
These connections must be made by a qualified
electrician. All electrical connections must meet
b
National Electrical Code or prevailing local codes.
Combined Speedcook and Warming Drawer
Installation
When installing the 8peedcook oven over a GE or
Honogram electric warming drawer, a separate 120V,
60Hz, properly grounded receptacle must be installed.
See instructions packed with the warming drawer.
WARNING
• The electrical power to the oven branch circuit
must be shut off while line connections are being
made.
• Use copper wiring only.
• Electrical
The free
must be
This wire
ground is required on this appliance.
end of the green wire {ground wire)
connected to a suitable ground.
must remain grounded to the oven.
• If cold water pipe is interrupted by plastic,
non-metallic gaskets, union connections or other
insulating materials, DO NOT use for grounding.
• DO NOT ground to a gas pipe.
• DO NOT have a fuse in the NEUTRAL or
GROUNDING circuit. A fuse in the NEUTRAL or
GROUNDING circuit could result in an electrical
shock.
• Check with a qualified electrician if you are in
doubt as to whether the appliance is properly
grounded.
Failure to follow these instructions
box within reach of the
could result in
serious injury or death.
4
Installation
Preparation
PreparationWITHOUTan AccessorgStorageDrawer
PREPARE THE OPENING
PREPARE THE OPENING (CONT.)
The Advantium
Installation over a GE/Monogram
Warming Drawer:
240V can be installed in
combination with other GE/Monogram appliances.
Always follow each product's Installation
Instructions to complete the installation.
Single
Advantium
23-1/2"
24OV Installation:
Order a 30" wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
J
30" •
23-1/2"
Construct
Solid Bottom
Min. 3/8"
Plywood
Supported
by 2x4 or 2x2
Runnersall
FourSides
2" Min.
_ (3" recommended)
4- 25-1/4"
"
g
drawer
requirement
17-1/2"
L_
J
36-3/4"
Min.
Construct
Base
Min. 3/8"
..\Plywood
Supported
by 2x4 or 2x2
Runners all
Four Sides
NOTE: Additional clearances between the cutouts
may be required. Check to be sure the oven supports
above the Warming Drawer location do not obstruct
the required interior depth and height. See Warming
Drawer installation instructions for details.
J
J
• Always maintain 36-3/4" minimum height from
the floor to the cutout in any single or combined
installation.
• Allow 2-1/8" case trim overlap on the sides and
7/8" overlap on the bottom of the opening for all
models. Allow 1-1/4" case trim overlap on the top
for models PSB2200 and PSB2201 and 3//4"
overlap on the top for models ZSC2200, ZSC2201
and ZSC2202.
• Oven overlaps will conceal cut edges on all sides
of the opening.
When installed over a single oven or a warming
drawer, allow at least 2" between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.
Construct a solid oven floor of 3/8" min. thick pluwood
supported bu 2 x 4 or 2 x 2 runners on all sides.
• The support must be level and rigidlu mounted,
flush with the bottom edge of the cutout.
S
Installation
Preparation
PreparationWITHOUTan AccessorgStorageDrawer
PREPARE THE OPENING (CONT,)
PREPARE THE OPENING {CONT.)
Installation
Installation
over a GE/Nonogram
Warming
Drawer:
over a GE/Monogram
25-1/4"
17-1/2"
Oven:
Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
Oven and
ConstructSolid
30"
23-1/2"
Bottom Min.
3/8" Plywood
Supportedby
2x4 or 2x2
Runnersall
FourSides
A
2" Min.
(3" recommended)
17-1/2"
Per Oven
Requirement
2" Min.
B"recommended)
Per Oven
Requirement
45-1/4"
Min.
2" Min.
_equirement
• If Uou are replacing a GE/Honogram electric
double oven with the combined installation of
an Advantium 2/40V and a single oven, use the
dimensions shown. The middle rail separating
the two openings mau need to be larger than
the 2" minimum shown.
NOTE: Additional
clearances
between the cutouts
ma U be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
CAUTION: For personal safet U, the mounting
surface must be capable of supporting the
cabinet load, in addition to the added weight of
this approximate 80-pound oven, plus additional
oven loads of up to 50 pounds or a total weight
of 130 pounds.
6
Installation
Preparation
Preparation WITHan AccessoryStorage Drawer
NOTE:MODELZSC2202CANNOTBE INSTALLEDWITH AN ACCESSORY
STORAGEDRAWER.SEEINSTALLATIONPREPARATION
WITHOUTAN ACCESSORY
STORAGEDRAWERFORTHISHODEL.
PREPARE THE OPENING
PREPARE THE OPENING
The Advantium 240V can be installed in
combination with other GE/Nonogram appliances.
Always follow each product's Installation
Instructions to complete the installation.
Single
Advantium
Single Advantium
Order a 30" wide single oven cabinet or cut the
opening in a wall to the dimensions shown.
23-1/2"
• The support must be level and rigidlu mounted,
flush with the bottom edge of the cutout.
4-
25-I/4"
Min*
Installation
over a GE/Monogram
Warming Drawer:
_"
23-1/2"
....
21"
3B-3/4"
Min.
(cont.)
Construct a solid oven floor of 3/8" min. thick pluwood
supported bu 2 x 4 or 2 x 2 runners on all sides.
}
I
240V Installation
When installed over a single oven or a warming
drawer, allow at least 2" between the two openings.
This separation will provide clearance for bottom
overlap of the Advantium 240V and the other
appliance overlaps.
24OV Installation:
30" _
{CONT.)
Construct
Base
Min 3/8"
_Plywood
Supported
by 2x4 or 2x2
Runnersall
FourSides
25-I/4"
Min. _
_
/
Construct
Solid Bottom
Min. 3/8"
Plywood
Supported
by 2x40r 2x2
Runnersall
FourSides
2" Min.
(3" recommended)
ig
drawer
requirement
* For existing cutouts, a maximum width of 28-1/2"
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
36-3/4"
Min.
• Always maintain 36-3//4" minimum height from
the floor to the cutout in any single or combined
installation.
* For existing cutouts, a maximum width of 28-1/2"
is acceptable. If the opening is slightI9 wider,
secure a furring strip on each side of the cutout
for securing the oven.
• Allow 3//4" to 2-1/8" case trim overlap on the sides
and 7/8" overlap on the bottom of the opening for
all models. The amount of overlap on the sides
depends on the actual cutout width. Allow 1-1/4"
case trim overlap on the top for models PSB2200
and PSB2201 and 3/4" overlap on the top for
models ZSC2200, ZSC2201 and ZSC2202.
NOTE: Additional clearances between the cutouts
mau be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
• Oven overlaps will conceal cut edges on all sides
of the opening.
7
Installation
Preparation
Preparation WITHan AccessoryStorage Drawer
NOTE:MODELZSC2202CANNOTBE INSTALLEDWITH AN ACCESSORY
STORAGEDRAWER.SEEINSTALLATIONPREPARATION
WITHOUTAN ACCESSORY
STORAGEDRAWERFORTHISHODEL.
PREPARE THE OPENING (CONT.)
PREPARE THE OPENING (CONT.)
Installation
Installation
over a GE/Monogram
Warming
Drawer:
30"
over a GE/Nonogram
23-1/2"
/
Oven:
Construct Solid
Bottom Min.
3/8" Plywood
Supported by
2x4 or 2x2
Runners all
Four Sides
Oven
and
ConstructSolid
30"
23-I/2"
Bottom Min.
3/8" Plywood
Supportedby
2x4 or 2x2
Runnersall
/ FourSides
2" Min.
(3" recommended)
2" Min.
(3" recommended)
Per Oven
Requirement
Per Oven
Requirement
45-1/4"
Min.
2" Min.
45-1/4"
Min. ,Perwarmingdrawerrequirement
/
/
* For existing cutouts, a maximum width of 28-1/2"
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
* For existing cutouts, a maximum width of 28-1/2"
is acceptable. If the opening is slightly wider,
secure a furring strip on each side of the cutout
for securing the oven.
NOTE: Additional clearances between the cutouts
° If you are replacing a GE/lonogram
electric
double oven with the combined installation of
an Advantium 240V and a single oven, use the
dimensions shown. The middle rail separating
the two openings mau need to be larger than
the 2" minimum shown.
mau be required. Check to be sure the oven
supports above the Warming Drawer location do
not obstruct the required interior depth and height.
See Warming Drawer installation instructions for
details.
CAUTION: For personal safetu, the mounting
surface must be capable of supporting the cabinet
load, in addition to the added weight of this
approximate 80-pound oven and 50-pound
drawer, plus additional oven loads of up to 50
pounds or a total weight of 160 pounds.
8
Installation
[]
Instructions
REMOVE THE PACKAGING AND PARTS
° Remove all packing material and tape.
• Locate parts package containing
mounting
screws.
• Remove the oven from the carton. Do not lift unit bg
handle or conduit. Two people are required to lift
this oven.
• Open the door and remove ang packaging
O_ner*g
Manual
in oven.
_nst_ll_tion
_nstructions
Rack
i
Owner's Manual
Cook Book
Installation
Instructions
Bottom
Trim
Cooking
Guide
<@
6 Brass Screws
Cook Book
Glass Trag
Metal Trags (2)
(3 required, 3 extra)
Cooking Guide
5 Color Hatched
Screws
(4 required, i extra)
IMPORTANT: If installing the Advantium 240V Oven
with an accessorg storage drawer, read the storage
drawer assemblg instructions to assemble the
products together before proceeding to Step 2.
Turntable Ring
Metal Grill Trag
9
Installation
[]
Instructions
ROUTE CONDUIT THROUGH
CUTOUT
CAUTIO N: Two people
[]
ROUTE CONDUIT THROUGH
CUTOUT (CONT.)
When connecting
circuit:
are required to lift
the oven into the opening. Grasp the bottom at
front and rear. Discard foam base. DO NOT USE
HANDLE OR CONDUIT TO LIFT THE OVEN. DAMAGE
WILL OCCUR.
to a 3-conductor
branch
• Connect oven red lead to branch circuit red lead.
• Connect oven black lead to branch circuit black
lead.
• Connect oven green ground lead and white lead
to branch circuit neutral (white or gray).
With oven in front of the cabinet opening:
• Insert conduit into cabinet opening. Connect oven
wiring and branch circuit.
B C(l_lduc!ol BralIch Cifcdit
• Lift the oven into the opening while continuing to feed
the conduit in the direction of the installed junction
box. Be sure the conduit does not get pinched
between the back of the oven and the cabinet wall.
Bral/ChCircLlit
!2BVAC
Red
Overs
OC
_
Bed
White or
• Leave oven a few inches forward
of the cabinet
Neutral
6ray
front frame. Do not push the unit all of the wag
into the cutout.
12OVAC
Black
_
G/_e/i
h
White
O(_
Back
J_
When connecting
circuit:
to a 4-conductor
branch
• Connect oven red lead to branch circuit red lead.
• Connect oven black lead to branch circuit black
lead.
• Break connection between oven white lead and
oven green ground lead.
• Connect oven white lead to branch circuit neutral
lead (white or grag).
• Connect oven green ground lead to branch circuit
ground lead (green or bare copper).
(Ovenshown without
4 Conductor Branch Circuit
accessorystorage drawer.)
Brarc
WARNING
• Disconnect power to the junction
making the electrical connection.
120VAC
box before
/20V A(;
(}1c J}t
Bed
Back
Oven
C) _
Bed
_
Blac
Bareo_
@e_r]
• Electrical ground is required on this appliance.
GND
• Do not connect the electrical supplg until
appliance is permanentlg grounded.
Neutral
GROUNDING INSTRUCTIONS
This appliance must be connected to a grounded,
metallic, permanent wiring sgstem, or an equipment
grounding connector should be run with the circuit
conductors and connected to the equipment
grounding terminal or lead on the appliance.
Failure to follow these instructions could result
in fire, personal injury or electrical shock.
10
C-reen
C)_
W/te
or (_ray
_
W
White
Installation
[]
Instructions
[]
INSTALL BOTTOM TRIM
INSTALL MOUNTING
NOTE: If installing the Advantium 2/40 Oven with an
accessoru storage drawer, the bottom trim is not
required. Proceed to Step/4.
j
SCREWS
mo
]
• Align bottom trim tabs to slots in the bottom of the
oven.
• Slide the oven the remaining wau into the opening
so that the side flanges and control panel are
against the cabinet frame. Hake sure that the oven
is centered in the opening.
nj
• Secure the bottom trim to the bottom of the oven
using 3 brass screws provided.
L
• Open the door, place a turntable trau in the oven
and make sure that the tra U in the unit is level.
• Drill pilot holes through the side flanges.
• Drive the color matched screws into the side
flanges. It is recommended
be hand tightened.
If installing
drawer:
that the screws
oven with an accessorg storage
• Open the drawee
• Drill pilot holes through the side flanges.
• Drive color match screws into the side flanges.
It is recommended that the screws be hand
tightened.
/
[
[]
FINALIZE INSTALLATION
• Turn power on at the source. The interior light
should come on when the door is opened.
• Refer to Owner's
11
Manual for operating
instructions.
Assembly Instructions
Advantium ®240V Built-ln Accessory Storage Drawer
J×2200, J×2201, Z×2201
BEFORE YOU BEGIN
MODELS AVAILABLE
Profile Models:
Read these instructions completely and carefully. Read
the Installation Instructions for the Advantium 240V oven
JX2200BB-Block
JX2201SS-Stoinless Steel
completely and carefully for cutout dimensions and
step-by-step instructions.
Monogram Models:
IM PORTANT- sove
these
instructions
for
ZX2201SS-Stainless Steel
local inspector's use.
IM PORTANT-
NOTE: Adventium 240V Built-In SpeedCook Oven
model ZSC2202SS CANNOT be installed with an
Observe oligoverningcodes
ond ordinonces.
eccessorg storoge drawer. See Installation
Preporotion Without on Accessorg Storoge Drower in
the Advontium 240V Built-In SpeedCook Oven
Instollotion Instructions for this model.
• NOTE TO INSTALLER: Be sure to leave these
instructions with the ConsumeE
• NOTE TO CONSUMER: Keep these instructions with
your Advantium 240V Oven Owner's Manual for
future reference.
• SKILL LEVEL: Installation of this appliance requires
basic mechanical skills.
PRODUCT DIMENSIONS AND CLEARANCES
• COMPLETION TIME: One hour with the installation
of an Advantium 240V oven.
,,
• Proper installation is the responsibility of the installeE
Allow 15" clearance
when fully open
• Product foilure due to improper instollution is not
covered under the Worrontg. See the Advontium
240V Oven Owner's Monuol for worruntg informution.
NOTE:Appearance will varg bg model.
TOOLS REQUIRED
• #2 Phillipsscrewdriver
PARTS SUPPLIED
• 2 Side Supports
• Screws
•
12
Screws{color matched)
ASSEMBLYTO ADVANTIUM 240V BUILT-IN SPEEDCOOK OVEN
[]
ASSEMBLING THE OVEN TO DRAWER
(CONT.)
REMOVE PACKAGING AND PARTS
• Remove the drawer from the carton.
[]
• Remove all packing material and tape.
• Open the drawer and remove ang parts inside.
Remove the front two bottom screws on each
side of the oven and the top center screw on
each side of the storage drawer.
• Locate parts.
II
A_sembly
Instructions
Side Supports {2)
J
Assemblg
Instructions
|
Screws (2 Sets)
[]
ASSEMBLING THE OVEN TO DRAWER
[]
Place storage drawer on a surface with the
front of drawer hanging over the edge of the
surface. Not placing the front edge of drawer
over the edge of the surface mag result in
damage to the drawer since the front edge of
drawer hangs below the bottom of drawer.
[]
J
[]
Place the side supports into the tabs on the
drawer and secure using the screws supplied
and the screws removed in Step C.
Place the oven on top of the storage drawer.
lake sure that the back and sides of the oven
align with the back and sides of drawer.
|
J
[]
NOTE: The bottom of the oven side flanges will
sit directlg in front of the top of the storage
drawer side flanges.
13
The oven and storage drawer assemblg is now
readg to be installed. Return to the Advantium
2/40V Built-In SpeedCook Oven Installation
Instructions to complete the installation.
14
15
NOTE: while performing installations described in this book,
safety glasses or goggles should be worn
NOTE: Product improvement is a continuing endeqvor at
General Electric Therefore, materials, appearance and
specifications are subject to change without notice
Printed in Korea
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY/40225
ge.com
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021