GE ZIFS240PBSS Wine Chiller - A Series installation Guide

Add to My manuals
12 Pages

advertisement

GE ZIFS240PBSS Wine Chiller - A Series installation Guide | Manualzz
 monogram.com
Read these instructions completely and carefully.
IMI \ | — Save these instructions
for local inspector’s use.
and ordinances.
Note to Installer - Be sure to leave these
instructions with the Consumer.
Note to Consumer - Keep these instructions with
your Owner’s Manual for future reference.
— Observe all governing codes
== This appliance must be
properly grounded. See below.
Consulter ci-dessous.
IT you received a damaged Fresh-Food Refrigerator
or Bar Refrigerator with Icemaker, you should
immediately contact your dealer or builder.
Skill Level - Installation requires basic mechanical
skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation
Is not covered under the GE Appliance Warranty.
e Use this appliance only for its intended purpose.
e Immediately repair or replace electrical service cords
that become frayed or damaged.
e Unplug the unit before cleaning or making repairs.
e Repairs should be made by a qualified service
technician.
e || ne faut utiliser cet appareil que pour l’usage pour
lequel il a été construit.
e || faut réparer ou remplacer immédiatement tout
cordon d'alimentation électrique effiloché ou
endommagé.
e Débranchez le réfrigérateur avant le nettoyage
ou toute intervention.
e Les réparations doivent être faites par un technicien
qualifié.
For Monogram local service in your area, call
1.800.444.1845
For Monogram service in Canada, call
1.800.561.3344
For Monogram Parts and Accessories, call
1.800.626.2002.
monogram.com
= Please read carefully.
FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong
(grounding) wall receptacle to minimize the possibility of electric shock hazard from this appliance.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Where a standard 2-prong wall outlet is encountered, it is your personal responsibility and obligation to have it replaced
with a properly grounded 3-prong wall outlet.
DO NOT, UNDER ANY CIRCUMSTANCES, CUT OR REMOVE THE THIRD
(GROUND) PRONG FROM THE POWER CORD.
DO NOT USE AN ADAPTER PLUG TO CONNECT THE REFRIGERATOR
TO A 2-PRONG OUTLET.
DO NOT USE AN EXTENSION CORD WITH THIS APPLIANCE.
Important Information
Parts Required
Caring for Your Stainless Steel
Tools, Hardware
Staining Wood Drawer Fronts
Install Water Line
Design Guide (For ZIFS240 and 2185240}
The Installation Space
Side-by-Side Installations
Product Clearances 5
Design Guide (For ZIFI240 and 2181240)
LA] LA] LA LA LA
un 4
The Installation Space 6
Side-by-Side Installations 7
Product Clearances 7
Installation Instructions
Step 1, Remove Packaging and Installation Parts ci. 8
Step 2, Install Custom 3/4" Door Panel and Handle
(Z1F1240 and ZiB1240 models only) 8,9
Step 3, Leveling 9
Step 4, Connect Water Supply
Z1B1240 and Z1BS240 models only) 9
Step 5, Connect Power 10
Step 6, Slide Product into Cutout 10
Step 7, Set Temperature Controls 10
ZIF1240 AND 2181240 MODELS ONLY
PARTS REQUIRED PARTS SUPPLIED
e Custom handle e Handle side trim
e Assembled overlay panel * Optional black or
e Screws stainless steel toekick
Before installation or first use, we strongly advise that
you polish the stainless steel exterior and handle with
a commercially available stainless steel cleaner such as
Stainless Steel Magic.” To preserve and protect the fine
finish, we also strongly advise that you apply stainless
steel cleaner monthly.
* Adjustable wrench
« Carpenter’s glue (ZIF1240 and ZIBI240 models only)
Screwdriver {ZIFI240 and ZIBI240 models only)
The drawer fronts are unfinished cherry wood. During use,
oil from hands may accumulate and stain the wood.
e The drawer fronts may be stained and sealed to match
adjacent cabinetry.
* Apply the stain and sealer according to the manufacturer’s
instructions. To avoid unpleasant odor, keep the door open
to ventilate and allow the stain/sealer to dry completely
before using the product.
A cold water supply is required for automatic icemaker
operation. The water pressure must be between 20 and
120 p.s.l.
* The water line can enter the opening through
the floor or back wall. Route 1/4" O.D. copper tubing or GE
SmartConnect” kit between the cold water line and water
connection location, long enough to extend to the front of
the refrigerator.
e Install an optional water filter in the water line near the
refrigerator. À water filter is recommended in areas where
the water supply contains sand and particles. Installation
Instructions are packed with the filter.
NOTE: The only GE approved plastic tubing is supplied in
the GE SmartConnect” Refrigerator Tubing kits. Do not use
any other plastic water supply line because the line is under
pressure at all times. Other types of plastic may crack or
rupture with age and cause water damage to your home.
GE SmartConnect” Refrigerator Tubing Kits are available
in the following lengths:
2'(0.6 m) = WXO8X10002
6'(1.8 m) WX08X10006
15" 46 M)
25' (7.6 m)
WXO08X10015
WX08X10025
(2181240 AND 2185240 MODELS ONLY]
Water Line Water Line
1-1/2"
min.
Floor
Shut off the main water supply.
Turn on the nearest faucet long enough to clear the line
of water.
e Install a shut-off valve (required) between the icemaker
water valve and cold water pipe in a basement or cabinet.
The shut-off valve should be located where it will be easily
accessible.
* Turn on the main water supply and flush debris. Run about
a quart of water through the tubing into a bucket. Shut off
water supply at the shut-off valve.
NOTE: Saddle type shut-off valves are included in many water
supply Kits, but are not recommended for this application.
NOTE: Commonwealth of Massachusetts Plumbing Codes
248CMR shall be adhered to. Saddle valves are illegal and use
is not permitted in Massachusetts. Consult with your licensed
plumber.
For models ZIFS240 and 2185240 with Stainless Steel Doors and Handles
Flush —
Installation 1/4"
В lh
NOTE: |
Water line location CABINET || 1 panel or cleat 0 be set CABINET
for ZIBS240 model E
only Front edge of product case ae
He в x |
da — В 23-3/1" Frontface %
} no” - |
Г These products will fit flush to \
ST ae md - adjacent cabinets when instalied with
. n a 1/4" filler panel or cleat. The filler
NOTE: | | panel should be recessed or set back
Handle and | 34-1/4" behind the door and even with the
handle standoff 26" I 24-3/4" front edge of the product case.
depth is 2-1/4". | to 34-3/
including
Handle |
*Рог а standard installation: The product must be installed so that —
the stainless steel front will project 1-5/8" forward of adjacent Standard
cabinets. This position will allow a full door swing and prevent | Installation |
interference with adjacent cabinetry. The opening between cabinets |
must be 23-3/4" minimum.
**For a flush installation: Install a 1/4"-wide filler strip on the hinge
side. The filler strip will act as a spacer between the door case and CABINET CABINET
adjacent cabinets and will prevent interference with the cabinet Front edge of product case {, 3
door swing. Recess the filler strip 1-5/8" back from the front face | | - a
of the refrigerator, or even with the front edge of the product case DMA | ; ed
(behind the gasket). The width of the opening must be 24" (including Fontiace (VIP
the 1/4" filler strip, In a standard installation, the product 120°
will project forward of adjacent ен
* All models may be used freestanding. cabinets. See Dim. A.
Additional Specifications Product NN IN a i.
* A 120 volt 60HZ., 15 or 20 amp power supply 15 >1BS240 >
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
For models ZIFS240 and 21B5240 with Stainless Steel Doors and Handles
SIDE-BY-SIDE INSTALLATIONS
For a complete refreshment center, install a Fresh-Food
Refrigerator beside a Double-Drawer Refrigerator,
Beverage Center or Wine Chiller/Wine Reserve. Or, install
a Refrigerator with Icemaker beside a Wine Chiller/Wine
Reserve,
A side-by-side installation requires at least a 47-1/2"-
wide minimum opening for standard installation and
48"-wide minimum opening for flush installation. No
trim kits required.
e Products must operate from separate, properly
grounded receptacles.
A
TT |
WALI ge In
| MN
©, /— 47-1/7" Min. Standard —\ 8
A 48" Min. Flush N
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110% door swing.
When installed in a corner:
e Allow 14" minimum clearance on the hinge side
for a full 110° door swing.
s Allow 4" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE: Clearances are based on the recommended
2-1/4" handle standoff depth.
14" Minimum to Wall f
«> 90 Door
swing 21-5/8
110 Door |
Swing - |
1 ни | |
= Th \ РЕ 23-5/8'
теж 4" Minimum to Wall
NOTE: Right-hand models illustrated. Allow the same
clearances on the opposite side for left-hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
Z185240 are not available with left-hand door swing.
e Test the door swing. Carefully open and close the door.
The door should not rub or catch on adjacent cabinetry.
Choose the location:
* These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
* Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
* These products are not designed to be stacked one
over the other.
For models ZIFI1240 and 21B1240 with Custom Door Panels and Handles
ATION SPACE THE INSTALLATION SPACE (соп*.)
f Standard \
— : installation
—
; 24 NOTE:
34-1/2"-35" 19 Max Water line location for CABINET CABINET
1-1/ Front edge of product case es
a — 23-3/4" Min. | | \ |
Dim. A I A4
[—Y A Front face \ A110°
NOTE: If installing between т Ne
и In a standard installation, the product 120°
frameless cabinets, a 1/2 Will project forward of adjacent >— A
wide filler strip or side panel 34-1/4' cabinets. See Dim. A.
may be needed on the hinge to 34-3/4" Product NA Dima"
side. The filler strip will act as roduc me
a spacer between the door | ENEE 2314
case and adjacent cabinet | a | 81240 e
and will prevent interference 24-7/8" N 3.5/8"
with the cabinet door swing. —
The width of the opening
must include the filler panels.
The product must be installed so that the custom panel front will
project 2-3/4" forward of adjacent cabinets. This position will allow a
full door swing and prevent interference with adjacent cabinetry. The
opening between cabinets must be 23-3/4" minimum. These models
can not be installed flush in 24"-deep cabinets.
e All models may be used freestanding.
Additional Specifications
* A 120 volt 60HZ., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.
Black or Stainless Steel Toekick Options
* These products are shipped with a stainless steel toekick
and a black toekick. For shipping purposes, one of the
toekicks will be secured to the back of the unit, and the
second will be installed on the unit. Keep the unused
toekick and any unused parts for future use.
For models ZIFI1240 and 21B1240 with Custom Door Panels and Handles
For a complete shment center, install a Fresh-Food
Refrigerator beside a Double-Drawer Refrigerator,
Beverage Center or Wine Chiller/Wine Reserve. Or, install
a Refrigerator with Icemaker beside a Wine Chiller/Wine
Reserve,
A side-by-side installation requires at least a 47-1/2"-
wide opening. No trim kits required.
e Products must operate from separate, properly
grounded receptacles.
PRODUCT CLEARANCES
The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
e Allow 16" minimum clearance on the hinge side
for a full 110° door swing.
¢ Allow 4-1/2" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE: Custom handle clearances may vary,
16" Minimum to Wall |
> 90 Door ,
Swing 21-5/8
110 Door |
Swing |
© \ 23-5/8'
AN 4-1/2" Minimum to Wall
wr
NOTE: Right hand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models Z1F1240 and ZIFS240 only. Models ZIBI240 and
Z\BS240 are not available with left hand door swing.
e Test the door swing. Carefully open and close
the door. The door should not rub or catch on adjacent
cabinetry. NOTE: When installing custom panel and
handle, use above clearances as a general guide but
adjust according to the installation.
Choose the location:
e These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
e Do not install these products where the temperature will
go below 55°F (13°C) or above 90°F (32°C).
e These products are not designed to be stacked one
over the other.
e Remove corner blocks and foam drawer stops.
* Remove all packing material, tape and protective
plastic coverings.
e Remove the toekick attached to the back of the unit.
e Remove the custom panel attached to the front of
the unit.
AC CAU TON: smal objects are a choke
hazard for children. Remove and discard any parts
not used.
‘ | EIN DEVIN © Les petits objets
peuvent Strangler les enfants. | faut jeter toutes
les pieces qui ne sont pas utilisées.
(ZIFI240 aı and. 2181240 models s onlu}
3/4" Overlay Panel Dimensions
Model ZIFI240 and ZIBI240 require sme
a field-installed overlay door panel.
| Overlay
e The overlay panel must be | Panel
secured to a 1/4" thick backer + Door
panel that slides into the trim. N
A .10" thick spacer panel must \
be placed between the overlay ;
and backer panel. 1/4" al
: . nc
* A custom handle of your choice, Backen Spacer
supplied by your cabinetmaker,
must be installed on this overlay panel. Countersink all
screws into the backer panel. Screws cannot protrude
from the backer panel.
IMPORTANT NOTE: Maximum total weight for custom
door panel is 25 pounds.
3/4" Overlay 23-5/8" 30°
| 0.10" Spacer 22-1/2" 29-1/16"
ANEL AND HA DLE (CONT)
(ZIF1240 and 2181240 models only)
Assemble overlay panels ==
with glue and screws. Overlay Panel Æ |
Spacer Panel | :
TT |
DA
e Center the spacer/backer '
panel on the overlay panel.
Secure with glue and screws. Countersink all screws
into the backer panel.
e Center spacer panel on the
backer panel, left to right and
top to bottom. Secure the
panels with glue.
Custom Panel Hinge Routing Dimensions
Use a 3/4" router bit to cut a notch into the back side of
the assembled panel 3/8" toward the front of the overlay
panel, 3/4" deep and 7/8" wide.
NOTE: Right-hand models
ilustrated. Cut notches on the
opposite side for left-hand fresh
~~ food door swing models
\ ZIFI240 and ZIFS240.
uu A Back side
| of custom
> panel
Install custom door panel and handle:
e Open door to 90°.
e Remove 5 screws holding trim; lift off trim.
Retain screws.
NOTE: Right-hand models
X illustrated. Follow the
_— same instructions on the
= opposite side for left-hand
> fresh food door swing
= models 711240 and
ZIFS240.
ANEL AND HANDLE (CO NT)
(ZIFI240 a and z 2181240 ) models onlu)
install custom door panel and handle (cont.):
* A custom handle of your choice, supplied by your
cabinetmaker, must be installed onto the overlay panel
before the panels are slid into the trim. Countersink all
screws into the backer panel. Screws cannot protrude
from the backer panel.
Screws Must
Be Countersunk
Into Panel
OTD TD
Handle
Custom -
Door Panels
e Slide overlay panel into the door trim.
e Reinstall the side trim using the trim screws removed
earlier.
my
Place the brushed decorative cover over the side trim
to hide the screw heads. Ensure side trim is aligned top
to bottom and front to back. Snap into place.
NOTE:
For shipping
purposes, the
brushed decorative
cover will be
secured to
the front of
the unit.
f
e Use an adjustable wrench
to turn the leveling legs and f
raise or lower the product.
For built-in installation, adjust
the leveling legs slightly below
the bottom of the countertop.
INSTALLATION TIP:
Measure floor to underside
of countertop inside the
opening. If the room floor |
is higher than the opening
floor, adjust the rear |
leveling legs approximately В -
1/8" less than the opening height. Screw front legs all
the way in to shorten the height at the front. This will
allow you to slightly tip the unit into the opening. Once
in the correct position, the front legs can be adjusted to
level the product.
| Turn Right to Lower
J ; Turn Left to Raise
SUPPLY
1/4
\, _ Compression
Nut
Ferrule
(sleeve)
SmartConnect™ Tubing
~~ Refrigerator
Connection
e Locate and bring the water line tubing to the rear
of the cabinet.
e Turn the water on to flush debris from the line.
Run about a quart of water through the tubing
into a bucket, then shut off the water,
Copper Tubing:
e Slip a 1/4" nut and ferrule over both ends of the copper
tubing. Insert the tube into the refrigerator connection
on the unit and tighten the nut.
e Turn on the water to check for leaks.
GE SmartConnect” Tubing:
e Insert the molded end of the tubing into the
refrigerator connection. Tighten the compression nut
until it is just hand tight.
e Tighten one additional turn with a wrench.
Overtightening can cause leaks!
e Turn on the water to check for leaks.
NOTE: Coil excess tubing length behind the unit.
e Connect power cord plug to a properly grounded
receptacle.
e Check to make sure power is on by opening the door
to see if interior light turns on.
* Bar Refrigerator with Icemaker - The interior fan runs
all the time except during defrost cycle when the door
is open.
e Fresh-Food Refrigerator - The interior fan runs
all the time except when the door is open.
See the Owner’s Manual for further explanation of the fan.
LAU | TUN. Do not push against the door
panel With u Jour r knees. Do not push or lift the unit by
the door handle. Damage may occur!
А, MALL JIN + Ne poussez jamais
le panneau de a porte c avec vos genoux. Ne poussez
jamais votre appareil ou ne le soulevez jamais par
la poignée de porte. Vous pouvez 'endommager.
e Open the door and gently push the unit back into
the opening with your hands against the sides.
Be careful not to entangle power cord.
* In a standard 24" opening, the front face of
the stainless steel door will be flush with adjacent
cabinetry. A custom panel door may protrude
1-3/4" beyond the surrounding cabinets.
e Check again to be sure the unit is level.
® [f the unitis installed under a countertop, adjust
the leveling legs until the unit is resting firmly against
the underside of the countertop.
e |f alignment with adjacent cabinetry Is an issue,
use a shim to secure the unit against the underside
of the countertop.
10
e The temperature controls are preset. Refer to
the Owner’s Manual for more information. Allow
12-24 hours for the temperature to stabilize.
NOTE: The Fresh-Food Refrigerator or Bar Refrigerator with
lcemaker operate very quietly. You may not notice the unit
running, and when first installed, the fans and motor may
not come on immediately - this is normal. If the display is
lit and the light is working, the unit is operating.
11
Pub. No. 31-51544-6
Part No. 197D5893P002
09-09 JR
Printed in Slovenia
NOTE: While performing installations described in this book,
safety glasses or goggles should be worn.
For Monogram® local service in your area, call
1.800.444.1845.
NOTE: Product improvement is a continuing endeavor
at General Electric. Therefore, materials, appearance
and specifications are subject to change without notice.
GE Consumer & Industrial
Appliances
General Electric Company
Louisville, KY 40225
GEAppliances.com

advertisement

Related manuals

advertisement