I Installation Instructions I If you have questions, 27" Built-In Wall Oven 911.47702,47703,47704,47709,47722,47724, 47729,47742,47743,47744,47749,47619 contact Before You Begin Read these instructions carefully and completely. • IMPORTANT-save instructions these for local inspector's use. • IMPORTANT-obeerve a. governing I Our website at: www.sears.com codes and ordinances. • Proper installation is the responsibility of the installer and product failure due to improper installation is NOT covered under the warranty. • NOTE--This grounded. appliance must be properly • ATTENTION INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. • Note to Installer--Be sure to leave these instructions with the consumer. • Note to Consumer--Keep these instructions for future reference. Materials Parts Included Needed Metal _ Bottom Trim Wire Nuts Single Ovens 9 Screws Double Ovens 13 Screws Strain Relief Clamp for 1/2" conduit Plastic Bottom Trim Junction Box (_ _- 36" of String Tools Needed Optional Metal Bottom Trim 1/8" Drill Bit and Electric or Hand Drill 229c4053P498-2 31-10517-2 (502 JR) 1 Phillips Screwdriver Installation Instructions IMPORTANT SAFETY INSTRUCTIONS Electrical Requirements For Your Safety • Be sure your oven is installed properly by a qualified installer or service technician. • Be sure the oven is securely installed in a cabinet that is firmly attached to the house structure. Weight on the oven door could cause the oven to tip and result in injury. Never allow anyone to climb, sit, stand or hang on the oven door. This appliance must be supplied with the proper voltage and frequency, and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse having amperage as noted on rating plate. (Rating Plate is located on oven side trim.) We recommend you have the electrical wiring and hookup of your oven connected by a qualified electrician, After installation, have the electrician show you where your main oven disconnect is located. • Make sure the cabinets and wall coverings around the oven can withstand the temperatures (up to 200°F) generated by the oven. Check with your local utilities for electrical codes which apply in your area. Failure to wire your oven according to governing codes could result in a hazardous condition, If there are no local codes, your oven must be wired and fused to meet the requirements of the National Electrical Code, ANSI/NFPA No. 70-Latest Edition. You can get a copy by writing: National Fire Protection Association Batterymarch Park Quincy, MA 02269 WARNING: The electrical power to the oven supply line must be shut off while line connections are being made. Failure to do so could result in serious injury or death, Effective January 1,1996, the National Electrical Code requires that new, but not existing, construction utilize a four-conductor connection to an electric oven. When installing an electric oven in new construction, a mobile home, recreational vehicle or an area where local codes prohibit grounding through the neutral conductor, follow the instructions in the section on NEW CONSTRUCTION AND FOUR-CONDUCTOR BRANCH CIRCUIT CONNECTION. You must use a three-wire, single-phase A.C. 208Y/120 Volt or 240/120 Volt, 60 hertz electrical system. If you connect to aluminum wiring, properly installed connectors approved for use with aluminum wiring must be used. 2 Installation Instructions Pre-lnstallation ON THE FOLLOWING PAGES IS TO BE USED FOR SINGLEAND DOUBLE ALL INFORMATION OVENINSTALLATION INSTALLATION! Checklist Door removal is not a requirement for installation of the product, but is an added convenience. To remove the door: III Ill [1[ Open the oven door as far as it will go. Remove packaging materials. Check behind hinges and under false bottom. Remove labels on the outside of the door, plastic on trims and panel and all tape around oven. Push both hinge locks down toward the door frame, to the unlocked position. This may require a flat blade screwdriver. _pE8 Hinge Unlocked Position Slot Hinge Arm DO NOT LIFT THE DOOR BY THE HANDLE! I _ I _ Place hands on both sides of the door, and close the oven door to the removal position. This is half way between the broil stop and fully closed. .., Open oven door and remove literature pack, broiler pan and grid, and oven racks. [_ Lift up and out door untilthe hinge arms clear the slots. Remove Installation Instructions from literature pack and read them carefully before you begin. Be sure to place all literature, Use and Care, Installations, etc. in a safe place for future reference. Hinge Clears Slot NOTE: The oven door is very heavy. Be sure you have a firm grip before lifting the oven door off the hinges. Use caution once the door is _emovedo Do not _ay the door on its handle. This could cause dents or scratches. 3 (Continued on following page) Installation Instructions Pre-lnstallation Place the oven on a table or platform even with the cutout opening. (Platform must support 150 Ibs. single, 275 Ibs. double.) Checklistoont. [&,JF" 4 Remove the bottom trim from the top of the oven. It will be installed at the end of the installation process, The trim is wrapped separately and taped to the top of the unit. Installation Instructions Cutout for Single Built-In Oven Cabinet Cabinet Width Junction 27" Width 27" Box Location Allow 7/8" for overlap of oven over side edges Recommended Minimum Cutout Location from Floor 32 1/2" Cutout Depth 23 1/2" Min. Cutout Width 25" Min. 22" MIn. above 2" x 4" or equivalent runners level with bottom of cutout Cutout base rail 25 1/4" Max. Cutout 27 5/8" Min. Height 28 1/8" Max. 20- have a front frame and the sides are less than 3/4" thick, shim both sides equally to OTE: If the does not establish the cabinet cutout width. JunCtion Box I_ocetion Allow for a minimum clearance comers, etc. when adjacent drawers, walls, door Recommended minimum cutout loCation from floor 32 1/2" of 20" to il is open T Allow 1" minimum for overlap of oven top and bottom of cutout If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight ovens, the runners support 150 Ibs. 2" x 4" or equivalent runners level with bottom of cutout of the oven. For single and braces must ] 24" NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks are covered. J or opening 27" -- This oven is not approved for stackable or side by side installation. 5 Installation Instructions Cutout for Double Built-In Oven Cabinet JunCtion Box Width 27" Location Recommended Cabinet Minimum Width 27- Allow 7/8" for ovedap of oven over side edges of cutout _ Cutout Width 25" Min. 25 114" Max Cutout Location from Floor 13 1/4" Cutout Depth 23 5/8" Min. Cutout Width 25" Min. 25 1/4" Max. 44" Above base rail Alternate 2" x 4" or equivalent runners level with bottom of cutout location 49 11116" Min. 50 118" Max. junction box Height drawers, 49 11/16" Min. NOTE: If the cabinet does not have a front frame and the sides are less than 314" thick, shim both sides equally to establish the cutout width. _- Recommended minimum cutout location from floor 131/4" / Allow s minimum of 20" for clearance to adjacent etc. when Height 50 1/8" Max, 5" 20 -j oorners, Cutout Cutout walls, door is open Allow 1 _ minimum for ovedxp of oven top and bottom of cutout If the cabinet does not have a solid bottom, two braces or runners must be installed level with the bottom of the cutout to support the weight of the oven. For double ovens, the runners and braces must support 275 Ibs. 2" X 4" or equlvalsut ruflnArs level with botom of cutout NOTE: If marks, blemishes or the cutout opening are visible above the installed oven, it may be necessary to add wood shims under the runners and front trim until the marks or opening are covered. 18" Over Centedine of Cabinet 6 _- Installation Instructions Cutout for Single Built-In Oven Under Counter Gas or electde cooktops may be installed over this oven. See cooktop installation instructions for cutout size. See label on top of oven for approved cooktop models. Gas and electrical connections for gas _;ooktop must be located in an adjacent accessible lOCation to the right. 24itV 1208V Junction Box Locstlon \ I I TOp andlor aide fillem may be neceeear_j if unit is positioned between existing cabinets. Be sure they are attached securely, since they will anchor the oven i the cabinet. - 25" Min. 25 1/4" Max. 27 5/8" Min. 28 1/8" Max. _- Allow 1" unit overlap all edges 22" Min. Above Support platform 32" Typical Countertop Height 24° L . ._ 3/4" Support Platform Required MUST SUPPORT 150 LBS. _t Ii_This d under a solid disk, induction oven is not approved to be III n 7 d_aft _u_r coo_op_ r Installation Instructions Electrical Connections ATTENTION [] [] INSTALLER All electric wall ovens must be hard wired (direct wired) into an approved junction box. A plug and receptacle is NOT permitted on these products. DO NOT shorten the flexible Turn off the circuit breaker or remove fuses to the oven branch circuit. With the oven supported on a table or platform in front of the cabinet opening, connect the flexible conduit to the electrical junction box as shown below. Position the conduit in such a manner that it will lie on top of the oven in a natural loop when the oven is installed. You will need to purchase an appropriate strain relief clamp to complete the connection of the conduit to the junction box. conduit. The conduit strain relief clamp must be securely attached to the junction box and the flexible conduit must be securely attached to the clamp. If the flexible conduit will not fit within the clamp, do not install the oven until a clamp of the proper size is obtained. Condu,t NOTE TO ELECTRICIAN: The 3 power leads supplied with this appliance are UL recognized for connection to heavier gauge household wiring. The insulation of these 3 leads is rated at temperatures much higher than the temperature rating of household wiring. The current carrying capacity of the conductor is governed by the wire gauge and the temperature rating of the insulation around the wire. I _1-. WARNING: Improper connection of aluminum house _" E_ f _ it_ _ 1 Strain Relief Clamp Ifl Placeo_,en on__ LU-'_ _" fnot=.cluded) _-_ support to ass=st in must be used at wiring to copper leads can result in an electrical hazard or fire. Use only connectors designed for joining copper to aluminum and follow the manufacturer's recommended procedure closely. connecting conduit 8 Junction Box (Continued on followingpage) Installation Instructions Electrical Connections cont. I "-----] New Construction and Four-Conductor Branch Circuit Connection • When installing in new construction, [] Three-Conductor Branch Circuit Connection When connecting to a three-conductor circuit, if local codes permit: or a. Connect the bare with the crimped the branch circuit in color), using a • When installing in a mobile home, or • When installing in a recreational vehicle, or • When local codes do not permit grounding through neutral: branch oven ground conductor neutral (white) lead to neutral (white or gray wire nut. a. Cut the neutral (white) lead from the crimp. Re-strip the neutral (white) lead to expose the proper length of conductor. Ground Wire _-_ Junction b. Connect the oven red lead to the branch circuit red lead in accordance with local codes, using a wire nut. Box Cover c. Connect the oven black lead to the branch circuit black lead in accordance with local codes, using a wire nut. If the residence red, black or white leads are aluminum conductors, see WARNING on page 8. b. Attach the appliance grounding lead (green or bare copper) in accordance with local codes. If the residence grounding conductor is aluminum, see WARNING on page 8. d. Install Junction Box Cover. c. Connect the oven neutral (white) lead to the branch circuit neutral (white or gray) in accordance with local codes, using a wire nut. d. Connect the oven red lead to the branch circuit red lead and the oven black lead to the branch circuit black lead in accordance with local codes, using wire nuts. If the residence red, black or white leads are aluminum conductors, see WARNING on page 8. e. Install Junction Box Cover. 9 Installation Instructions Securing the Oven in the Opening [] Sliding the Oven Into the Opening [] a, Loop (do not tie) a 36" string around the conduit before the oven is slid into place. This will keep the conduit from falling behind the oven. Drilling the Pilot Holes and Mounting the Oven NOTE: Before drilling the pilot holes, _1 make sure the oven is pushed as far back into the opening as it will go and centered, Drill six 1/8" pilot holes through the mounting holes (top and bottom) of the side trim, for the #8 screws provided. Drill ten holes for the Double Oven. string loop while pushing the oven into Pull out on '1 the cabinet The screws must be a minimum of 1/4" from the front of the cutout. b. Lift oven into cabinet cutout using the oven opening as a grip. Carefully push against oven front frame. Do not push against outside edges. c. As you slide the oven back, pull the string so that the conduit will lie on top of the oven in a natural loop. WARNING: Mounting screws must be used. Failure d. When you are sure the conduit is out of the way, slide the oven 3/4 way back into the opening. Remove the String by pulling on one end of the loop. do so could result falling out of the cabinet serious injury. to in the oven causing b. Secure the oven to cabinet with screws provided. NOTE: If the cabinet is particle board, you must use #8 x 3/4" particle board screws. These may be purchased at any hardware store. 10 (Continued on following page) Installation Instructions To install a single metal bottom trim assembly (on some models), use sections C3 and C4. To install a metal bottom trim with a plastic bottom trim (on some models), use sections C3-C5. [_ Preparing for the Bottom Trim Installation Installing the Plastic Bottom Trim (on some models) a. With oven installed, take the bottom trim and center it on the bottom front edge of the cabinet opening. b. Using the trim as a template, mark the center of each slot (three total) where the mounting holes will be drilled. b. Find the key slot on the back of the trim. With Lower 3_lm in Position, Mark (3) Mounting Hole Locations c. Remove the trim. d. Drill pilot holes into the center of each template mark. [] a. Make sure flat side is up on the plastic bottom trim. Key Hole Slot and Wide Flange Remove Lower Trim Before Pre-drilling Mounting Holes at Top c. Match the key slot with the rivet on the bottom of the side trim, and lower the trim onto the rivet. Installing the Metal Bottom Trim a. Place the bottom metal trim centered over the pre-drilled mounting holes. Tape the edges of the trim down to maintain the alignment. rim Mounting Rivet of Metal Lower Trim d. Push the trim down, at both ends, until it snaps into place. Side JTdm Trim Screws Side Metal Lower Trim b. Using three trim screws provided, secure the bottom trim to the bottom edge of the cabinet. removed from A aik CAUTION: Besureyou do not tip the oven forward during installation or you may bend the bottom trim. The bottom trim provides an opening _'or cooling _ir to enter the cabinet. This opening should never be blocked. If this unit is ever the cabi;_et or the oven is ever pulled out for service, the trim must be removed first or damage to the trim will occur. 11 Installation Instructions Replacing the Oven Door I-_ NOTE: The oven door is heavy. You may need help lifting the door high enough to slide it into the hinge slots. Do not lift the door by the handle. Open the oven door as far as it will open. I-D-'4] front Push frame the hinge upcavity, againstto the of thelocks oven the locked position. 1-_ Hinge in Locked Position Lift the oven door by placing one hand on each side. The door is heavy, so you may need help. Do not lift the door by the handle. Notch of Hinge ly Fitted into I Hinge Slot I [] I-_ With the door at the same angle as the removal position (half way between the closed and broil stop position, seat the notch of the hinge arm into the bottom edge of the hinge slot. The notch of the hinge arm must be fully seated into the bottom of the slot. Hinge Arm of Slot Hinge Notch 12 Close the oven door. Installation Instructions Pre-Test Checklist [_ Remove all protective film, if present, and any stickers. [_ Check that the bottom trim is installed properly (see page 11). [_ Check benot sure that allorwiring is secure to and pinched in contact with moving parts. I_ Check to be sure the mounting screws are installed and flush with the side trim (see page 10). Operation Checklist Remove all items from the inside of the oven. NOTE TO ELECTRICIAN: The power leads supplied with this appliance Check that conduit is securely connected to the junction box. are UL recognized for connections to larger gauge household wiring. The insulation of these leads is rated at temperatures much higher than the temperature rating of household wiring. The current carrying capacity of a conductor is governed by the wire gauge and also the temperature rating of the insulation around the wire. Turn on the power to the oven. (Refer to your Use and Care Guide.) Verify that the bake and broil units, and all cooking functions operate properly. Check that the circuit breaker is not tripped nor the house fuse blown. NOTE: ALUMINUM WIRING A,WARNING: IMPROPER See your Use and Care Guide for troubleshooting list. CONNECTION OF ALUMINUM HOUSE WIRING TO THE COPPER LEADS CAN RESULT IN AN ELECTRICAL HAZARD OR FIRE, B. Splice copper wires to aluminum wiring using special connectors designed and UI. approved for joining copper to aluminum, and follow the manufacturer's recommended connector procedure closely. NOTE: Wire used, location and enclosure of splices, etc., must conform to good wiring practice and local codes. 13 NOTES 14
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project
advertisement
© 2021