KitchenAid 5KSM3311XAHT0 Stand Mixer Owner's Manual

Add to my manuals
16 Pages

advertisement

KitchenAid 5KSM3311XAHT0 Stand Mixer Owner's Manual | Manualzz

5KSM3311

W10868696D_v01.indd 1 10/6/16 9:53 AM

PARTS AND FEATURES

PARTS AND ACCESSORIES

Attachment hub

Motor head

Beater shaft

Flat beater

Speed control

Bowl

Wire whip

Dough hook

2

| PARTS AND FEATURES

W10868696D_v01.indd 2

Flex Edge beater*

Pouring shield*

*Accessory sold separately

10/6/16 9:53 AM

STAND MIXER SAFETY

Flat beater

Bowl

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions. Misuse of appliance may result in personal injury.

2. To protect against risk of electrical shock, do not put

Stand Mixer in water or other liquid.

3. Unplug the Stand Mixer from outlet when not in use, before putting on or taking off parts, and before cleaning.

4. This appliance can be used by children aged from

8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

W10868696D_v01.indd 3

STAND MIXER SAFETY |

3

10/6/16 9:53 AM

STAND MIXER SAFETY

5. This appliance is not intended for use by persons, including children, with reduced physical sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instructions concerning use of the appliance in a safe way and understand the hazards involved.

6. The appliance is not to be used by children. The appliance and cord should be out of reach of children.

7. Avoid contacting moving parts. Keep hands, hair, and clothing, as well as spatulas and other utensils, away from beater during operation to reduce the risk of injury to persons and/or damage to the Stand Mixer.

8. Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any manner. Return appliance to the nearest Authorised Service Centre for examination, repair or adjustment.

9. The use of accessories not recommended or sold by KitchenAid may cause fire, electric shock or injury.

10. Do not use the Stand Mixer outdoors.

11. Do not let the cord hang over the edge of table or counter.

12. Do not let the cord contact hot surfaces, including the stove.

13. Remove the flat beater, wire whip, or spiral dough hook from the Stand Mixer before washing.

14. This appliance is intended to be used in household and similar applications such as:

- staff kitchen areas in shops, offices or other working environments.

- farm houses.

- by clients in hotels, motels and other residential type environments.

- bed and breakfast type environments.

SAVE THESE INSTRUCTIONS

This appliance should not be used in any commercial application and will void all warranty.

4

| STAND MIXER SAFETY

W10868696D_v01.indd 4 10/6/16 9:53 AM

STAND MIXER SAFETY

ELECTRICAL REQUIREMENTS

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

Voltage: 220-240 V

Frequency: 50-60 Hz

Wattage: 250 Watts

NOTE:

The power rating for your

Stand Mixer is printed on the serial plate.

Do not use an extension cord. If the power supply cord is too short, have a qualified electrician or serviceman install an outlet near the appliance.

The maximum rating is based on the attachment that draws the greatest load (power). Other recommended attachments may draw significantly less power.

USING THE STAND MIXER

CHOOSING THE RIGHT ACCESSORY

ACCESSORY

FLAT BEATER

FLEX EDGE BEATER*

USE TO MIX

DESCRIPTION

Normal to heavy mixtures

Cakes, Creamed frostings, Candies,

Cookies, Biscuits, Pie pastry, Meat loaf,

Mashed potatoes

WIRE WHIP

DOUGH HOOK

Mixtures that need air incorporated

Eggs, Egg whites, Heavy cream,

Boiled frostings, Sponge cakes,

Mayonnaise

Mixing and kneading yeast doughs

Breads, Rolls, Pizza dough, Buns

W10868696D_v01.indd 5

STAND MIXER SAFETY |

5

10/6/16 9:53 AM

USING THE STAND MIXER

SPEED CONTROL GUIDE

All speeds have the Soft Start feature which automatically starts the Stand Mixer at a lower speed to help avoid ingredient splash-out and “flour puff” at start-up, then quickly increases to the selected speed for optimal performance.

NOTE:

The speed control can be set between the speeds listed in the chart to obtain speeds 1, 3, 5, 7, and 9 if a finer adjustment is required. Do not exceed Speed 2 when preparing yeast doughs as this may cause damage to the Stand Mixer.

SPEED ACCESSORY ACTION

½

1

2

4

STIR

DESCRIPTION

For starting all mixing procedures, slow stirring, combining, and mashing. Use to add flour and dry ingredients to batter, and to add liquids to dry ingredients.

Do not use Speed 1 to mix or knead yeast doughs.

SLOW MIXING For slow mixing, mashing, faster stirring.

Use to mix and knead yeast doughs, heavy batters, and candies; start mashing potatoes or other vegetables; cut shortening into flour; mix thin or splashy batters.

MIXING,

BEATING

For mixing semi-heavy batters, such as cookies. Use to combine sugar and shortening, and to add sugar to egg whites for meringues. Medium speed for cake mixes.

6

BEATING,

CREAMING

For medium-fast beating (creaming), or whipping. Use to finish mixing cake, doughnut, and other batters. High speed for cake mixes.

8

10

FAST BEATING,

WHIPPING

For whipping cream, egg whites, and boiled frostings.

FAST WHIPPING For whipping small amounts of cream, or egg whites; for final whipping of mashed potatoes.

6

| USING THE STAND MIXER

W10868696D_v01.indd 6 10/6/16 9:53 AM

USING THE STAND MIXER

ASSEMBLING THE STAND MIXER

1

Check to be sure that the Stand

Mixer is unplugged, and the speed control is turned to “0”.

NOTE:

To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

2

Raise the motor head:

Slide the locking lever to the unlock position and lift the motor head. Once lifted, slide the locking lever to the lock position to keep the motor head up.

3

Attach the bowl:

Place the bowl on the bowl clamping plate and gently turn it in a clockwise direction to lock it into place.

4

Attach any accessory:

Slip the accessory onto the beater shaft and press upward as far as possible. Turn the accessory counterclockwise to hook the accessory over the pin on the shaft.

W10868696D_v01.indd 7

USING THE STAND MIXER |

7

10/6/16 9:53 AM

USING THE STAND MIXER

5

Lower the motor head:

Slide the locking lever to the unlock position and guide the motor head down.

Make sure motor head is completely down, then slide the locking lever to the lock position. Before mixing, test lock by attempting to raise the motor head.

(OPTIONAL) To adjust beater to bowl clearance:

Tilt the motor head back; then turn the screw slightly counterclockwise (left) to raise the beater, or clockwise (right) to lower the beater. Adjust the beater so that it just clears the surface of the bowl. If you over adjust the screw, the bowl lock lever may not lock into place.

(OPTIONAL) Place the pouring shield*:

Slide the pouring shield* from the front of the Stand Mixer over the bowl until the pouring shield* is centred. The bottom rim of the pouring shield* fits inside of the bowl.

The pouring chute will be just to the right of the attachment hub as you face the Stand Mixer.

IMPORTANT:

Your Stand Mixer is adjusted at the factory so that the flat beater just clears the bottom of the bowl. If, for any reason, the flat beater hits the bottom of the bowl or is too far away from the bowl, you can easily adjust the clearance.

NOTE:

When properly adjusted, the flat beater will not strike on the bottom or sides of the bowl. If the flat beater or the wire whip is so close that it strikes the bottom of the bowl, coating may wear off the beater or wires on the whip may wear.

*Accessory sold separately

8

| USING THE STAND MIXER

W10868696D_v01.indd 8 10/6/16 9:53 AM

USING THE STAND MIXER

OPERATING THE STAND MIXER

NOTE:

The Stand Mixer may warm up during use. Under heavy loads with extended mixing time, the top of the unit may become hot. This is normal.

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

1

Plug the Stand Mixer into a grounded outlet. Always set the speed control lever on lowest speed to start, then gradually increase speed to avoid splashing ingredients. See the “Speed control guide” to select the best speed for your recipe.

NOTE:

To move the speed control lever with ease, lift slightly up as you move it across the settings in either direction.

W10868696D_v01.indd 9

2

Do not scrape the bowl while the

Stand Mixer is operating. The bowl and beaters are designed to provide thorough mixing without frequent scraping. Scraping the bowl once or twice during mixing is usually sufficient.

USING THE STAND MIXER |

9

10/6/16 9:53 AM

USING THE STAND MIXER

NOTE:

The pouring shield* can be used to avoid ingredients splashing out of the bowl when mixing as well as to easily pour ingredients in the bowl while mixing.

(OPTIONAL)

Pour ingredients into the bowl through the pouring chute.

DISASSEMBLING THE STAND MIXER

1

Raise the motor head:

Check to be sure that the Stand Mixer is unplugged, and the speed control is turned to “0”; then slide the locking lever to the unlock position and lift the motor head. Once lifted, slide the locking lever to the lock position to keep the motor head up.

(

OPTIONAL) Remove the pouring shield*:

Lift the front of the pouring shield* clear of the rim of the bowl, and pull away from the Stand Mixer.

*Accessory sold separately

10

| USING THE STAND MIXER

W10868696D_v01.indd 10 10/6/16 9:53 AM

USING THE STAND MIXER

2

Remove the accessory:

Turn the speed control to “0”, unplug the

Stand Mixer, and tilt the motor head back; then, press the accessory upward as far as possible, then turn the accessory clockwise and pull it away from the beater shaft.

3

Remove the bowl:

Gently turn the bowl counterclockwise to release it from the bowl clamping plate.

OPTIONAL ATTACHMENTS

KitchenAid offers a wide range of optional attachments such as the spiralizer, pasta cutters, or food grinders that may be attached to the Stand Mixer attachment power shaft as shown here.

1

Check to be sure that the Stand

Mixer is unplugged, and the speed control is turned to “0”.

2

Turn the attachment knob counterclockwise to remove attachment hub cover.

W10868696D_v01.indd 11

USING THE STAND MIXER |

11

10/6/16 9:53 AM

USING THE STAND MIXER

3

Insert attachment into attachment hub, making certain that attachment power shaft fits into the square attachment hub socket. It may be necessary to rotate the attachment back and forth. When it is in the proper position, the pin on the attachment will fit into the notch on the hub rim.

4

Tighten the attachment knob by turning it clockwise until the attachment is completely secured to the Stand Mixer. See the

“Instructions” manual that came with your attachment for detailed directions on using the attachment.

NOTE:

Make sure attachment knob is securely tightened after removal or replacement of attachments.

CARE AND CLEANING

CLEANING THE STAND MIXER

IMPORTANT:

Do not wash the wire whip in the dishwasher. Do not immerse the

Stand Mixer body in water or other liquids. These parts should be hand washed.

1

Turn Stand Mixer off and unplug before cleaning. Wipe the Stand

Mixer body with a soft, damp cloth.

Do not use household/commercial cleaners. Wipe off the beater shaft frequently to remove any accumulation of residue. Do not immerse in water.

2

The bowl, flat beater, dough hook,

Flex Edge beater*, and pouring shield* (top shelf only) may be washed in a dishwasher; or, clean them thoroughly in hot, sudsy water and rinse completely before drying.

Do not store beaters on the shaft.

*Accessory sold separately

12

| CARE AND CLEANING

W10868696D_v01.indd 12 10/6/16 9:53 AM

CARE AND CLEANING

3

The wire whip is not dishwasher safe. Clean it thoroughly in hot, sudsy water and rinse completely before drying. Do not store the wire whip on the shaft.

TROUBLESHOOTING

Electrical Shock Hazard

Plug into an earthed outlet.

Do not remove earth prong.

Do not use an adapter.

Do not use an extension cord.

Failure to follow these instructions can result in death, fire, or electrical shock.

If your Stand Mixer should malfunction or fail to operate, please check the following:

1.

The Stand Mixer may warm up during use. Under heavy loads with extended mixing time periods, you may not be able to comfortably touch the top of the unit. This is normal.

2.

The Stand Mixer may emit a pungent odor, especially when new. This is common with electric motors.

3.

If the flat beater hits the bowl, stop the

Stand Mixer. See the “Assembling the

Stand Mixer” section and adjust the beater to bowl clearance.

4.

If your Stand Mixer should malfunction or fail to operate, please check the following:

• Is the Stand Mixer plugged in?

• Is the fuse in the circuit to the Stand

Mixer in working order? If you have a circuit breaker box, be sure the circuit is closed.

• Turn off the Stand Mixer for

10-15 seconds, then turn it back on. If the Stand Mixer still does not start, allow it to cool for 30 minutes before turning it back on.

Do not return the Stand Mixer to the retailer; retailers do not provide service.

For additional assistance, contact Customer

Service at:

AU:

1800 990 990

NZ:

0800 881 200

Please have your product serial number ready when calling.

W10868696D_v01.indd 13

TROUBLESHOOTING |

13

10/6/16 9:53 AM

W10868696D_v01.indd 14 10/6/16 9:53 AM

W10868696D_v01.indd 15 10/6/16 9:53 AM

W10868696D

© 2016. All rights reserved.

Specifications subject to change without notice.

W10868696D_v01.indd 16

10/16

10/6/16 9:53 AM

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement