Klimaire PTAC15H502-KC, PTHP09H352-KC, PTAC12H352-KC, PTAC15H352-KC, PTHP15H502-KC, PTHP12H352-KC, PTHP15H352-KC, PTAC09H352-KC Installation guide

Klimaire PTAC15H502-KC, PTHP09H352-KC, PTAC12H352-KC, PTAC15H352-KC, PTHP15H502-KC, PTHP12H352-KC, PTHP15H352-KC, PTAC09H352-KC Installation guide
PTAC/PTHP
PACKAGED TERMINAL AIR CONDITIONER / HEAT PUMP
Installation & Operation
Manual
Mark of Superior Quality
IMPORTANT NOTE:
Read this manual carefully before installing
or operating your new air conditioning
unit. Make sure to save this manual for
future reference.
Before using your air conditioner, please read
this manual carefully and keep it for future reference.
For more information please visit www.klimaire.com
CONTENTS
1. SAFETY PRECAUTIONS....................................................................2
2. IMPORTANT SAFETY INSTRUCTIONS ............................................5
3. AIR CONDITIONER FEATURES.........................................................6
4. CONTROL PANEL OPERATION........................................................7
5. DIP SWITCHES CONFIGURATION....................................................8
6. DIP SWITCHES CONFIGURATION BY PANEL CONTROL.............10
7. WALL THERMOSTAT TERMINAL....................................................11
8. INSTALLATION..................................................................................13
9. CARE AND CLEANING.....................................................................15
10. TROUBLESHOOTING.....................................................................16
Read This Manual
Inside you will find many helpful hints on how to use and maintain your air conditioner
properly. Just a little preventive care on your part can save you a great deal of time and
money over the life of your air conditioner. You'll find many answers to common problems
in the chart of troubleshooting tips. If you review our chart of Troubleshooting Tips first, you
may not need to call for service at all.
CAUTION
This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understand the hazards involved. Children shall not play the appliance. Cleaning
and user maintenance shall not be made by children without supervision. ( be applicable
for the European Countries )
This appliance is not intended for use by persons (including children) with reduced physical ,
sensory or mental capabilities or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety. (be applicable for other countries except the European Countries )
Children should be supervised to ensure that they do not play with the appliance.
If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
The appliance shall be installed in accordance with national wiring regulations.
Do not operate your air conditioner in a wet room such as a bathroom or laundry room.
The appliance with electric heater shall have at least 1 meter space to the combustible
materials.
Contact the authorised service technician for repair or maintenance of this unit.
Contact the authorised installer for installation of this unit.
When there are wide differences between USER S MANUAL and Remote controller
Illustration on function description,the description on USER S MANUAL shall prevail.
If the air conditioner is knocked over during use, turn off the unit and unplug it from the main
power supply immediately. Visually inspect the unit to ensure there is no damage. If you
suspect the unit has been damaged, contact a technician or customer service for assistance.
In a thunderstorm, the power must be cut off to avoid damage to the machine due to lightning.
To reduce the risk of fire or electric shock, do not use this fan with any solid-state speed
control device.
Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar
coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic
area and where it will not be tripped over.
1
SAFETY PRECAUTIONS
To prevent injury to the user or other people and property damage, the following instructions
must be followed. Incorrect operation due to ignoring of instructions may cause harm or
damage. The seriousness is classified by the following indications.
WARNING
This symbol indicates the possibility of death or serious injury.
CAUTION
This symbol indicates the possibility of injury or damage to property.
Meanings of symbols used in this manual are as shown below.
Never do this.
!
Always do this.
WARNING
!
!
!
Otherwise, it may cause
Do not operate or stop
the unit by inserting or
pulling out the power
plug.
It may cause electric shock
electric shock or fire due
to excess heat generation.
or fire due to heat
generation.
Do not modify power
cord length or share
the outlet with other
appliances.
Do not operate with
wet hands or in damp
environment.
It may cause electric shock
or fire due to heat
generation.
It may cause electric shock.
Always ensure
effective earthing.
Do not allow water to
run into electric parts.
!
Incorrect earthing may
It may cause failure of
machine or electric
shock.
Incorrect installation may
Plug in power plug
properly.
cause electric shock.
!
Unplug the unit if
strange sounds, smell,
or smoke comes from
it.
It may cause fire and
electric shock.
Do not damage or
use an unspecified
power cord.
It may cause electric shock
or fire.If the power cord is
damaged, it must be replaced
by the manufacturer or an
authorised service centre or
a similarly qualified person
in order to avoid a hazard.
Do not direct airflow
at room occupants
only.
This could damage your
health.
Do not use the socket
if it isloose or
damaged.
It may cause fire and
electric shock.
2
Always install circuit
breaker and a
dedicated power
circuit.
cause fire and electric
shock.
Do not open the unit
during operation.
It may cause electric shock.
WARNING
!
!
Keep firearms away.
Do not use the power
cord close to heating
appliances.
It may cause fire.
It may cause fire and electric
shock.
Do not use the power cord
near flammable gas or
combustibles, such as
gasoline, benzene, thinner, etc.
It may cause an explosion
or fire.
Ventilate room before operating
air conditioner if there is a gas
leakage from another appliance.
Do not disassemble or modify
unit.
It may cause explosion, fire and, burns.
It may cause failure and electric shock.
CAUTION
Do not clean the air
conditioner with water.
When the air filter is to
be removed, do not touch
the metal parts of the unit.
It may cause an injury.
!
When the unit is to be
cleaned, switch off, and
turn off the circuit
breaker.
Do not clean unit when
power is on as it may cause
fire and electric shock, it may
cause an injury.
!
Stop operation and
close the window in
storm or hurricane.
!
Water may enter the unit and
degrade the insulation. It may
cause an electric shock.
An oxygen shortage
Do not put a pet or house
plant where it will be
exposed to direct air flow.
Do not use for
special purposes.
may occur.
Do not use this air
This could injure the pet or
conditioner to preserve
precision devices, food,
pets, plants, and art
objects.It may cause
deterioration of quality,
etc.
plant.
!
Ventilate the room
well when used
together with a stove,
etc.
Hold the plug by the
head of the power
plug when taking it out.
Operation with windows
It may cause electric shock
opened may cause wetting
of indoor and soaking of
household furniture.
and damage.
3
!
Turn off the main
power switch when
not using the unit
for a long time.
It may cause failure of
product or fire.
CAUTION
Do not place obstacles
around air-inlets or
inside of air-outlet.
!
Ensure that the installation
bracket of the outdoor
appliance is not damaged
due to prolonged exposure.
It may cause failure of
If bracket is damaged, there
appliance or accident.
is concern of damage due to
falling of unit.
Do not use strong
detergent such as wax
or thinner but use a soft
cloth.
Do not place heavy object
on the power cord and
ensure that the cord is
not compressed.
Appearance may be
There is danger of fire or
deteriorated due to change
of product color or
scratching of its surface.
electric shock.
!
Use caution when unpacking and
installing. Sharp edges could cause
injury.
!
Clean the evaporator once every
three months by professional people.
!
Otherwise it may cause failure of electric
heating feature.
4
!
Always insert the
filters securely. Clean
filter once every two
weeks.
Operation without filters
may cause failure.
Do not drink water
drained from air
conditioner.
It contains contaminants and
could make you sick.
If water enters the unit, turn the unit
off at the power outlet and switch
off the circuit breaker. Isolate supply
by taking the power-plug out and
contact a qualified service technician.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
NOTE The power supply cord with
this air conditioner contains a current
detection device designed to reduce
the risk of fire.
Please refer to the section Operation
,
of Current Device for details.
In the event that the power supply
cord is damaged, it cannot be
repaired-it must be replaced with a
cord from the Product Manufacturer.
,
Do not, under any
circumstances, cut,
remove, or bypass
the grounding prong.
Power supply cord
with 3-prong grounding plug
and current detection device
For your safety
Do not store or use gasoline or other flammable vapors
and liquids in the vicinity of this or any other appliance.
Avoid fire hazard or electric shock. Do not use an
extension cord or an adaptor plug. Do not remove any
prong from the power cord.
WARNING
Electrical Information
Be sure the electrical service is adequate for the model
you have chosen. This information can be found on the
serial plate, which is located on the side of the cabinet
and behind the grille.
Be sure the air conditioner is properly grounded. To
minimize shock and fire hazards, proper grounding is
important. The power cord is equipped with a three-prong
grounding plug for protection against shock hazards.
Your air conditioner must be used in a properly grounded
wall receptacle. If the wall receptacle you intend to use is
not adequately grounded or protected by a time delay
fuse or circuit breaker, have a qualified electrician install
the proper receptacle.
Ensure the receptacle is accessible after the unit installation.
Do not run air conditioner without side protective cover in
place. This could result in mechanical damage within the
air conditioner.
The appliance shall be installed in accordance with national
wiringregulations.
Do not use an extension cord or an adapter plug.
NOTE:
The shape may be different according to its model:
Power Card
Power Suppy
230V,15A
230V,20A
230V,30A
5
265V,15A
265V,20A
265V,30A
Operation of Current Device(optional)
The power supply cord contains a current device that senses damage to the power cord. To test your power
supply cord do the following:
1. Plug in the Air Conditioner.
2. The power supply cord will have TWO buttons on the plug head.
Press the TEST button, you will notice a click as the RESET
button pops out.
3. Press the RESET button, again you will notice a click as the button
engages.
4. The power supply cord is now supplying electricity to the unit.
(On some products this it also indicated by a light on the plug head.)
NOTES:
Do not use this device to turn the unit on or off.
Always make sure the RESET button is pushed in for correct operation.
The power supply must be replaced if it fails reset when either the TEST button is pushed, or it cannot be
reset. A new one can be obtained from the product manufacturer.
If power supply cord is damaged, it cannot be repaired. It MUST be replaced by one obtained from the
product manufacturer.
When 265V units are to be installed,the power supply must be permanent wiring.Permanent
wiring may be done through the accessory subbase.An exposed cord connection on 265V units
are not permitted.
AIR CONDITIONER FEATURES
This unit has many featrues.The servicer must be
familiar with these features in order to properly
service the unit.
Compressor Restart Delay
This feature extends the overall life of compressor by preventing the short-cycling of the air
conditioner.When the compressor restarts,the
unit is designed to give a minimum of three
minutes to have a time of equalizing the refrigerant pressures for optimizing cycling.
Memory
The unit has memory .If power is lost,all of the
control settings(mode,fan speed,on/off and
configuration) are remembered.So when power
is restored,the unit will start back up in the mode
(and configuration) it was in,when power was
lost.
Automatic Quick Warm-up (for heat pump
models only)
If the room temperature falls to 4.5 OC/8 OF
below the set point temperature,the reverse
cycle heat is shut off and the electric strip heat
is turned on for one cycle,until heating is
satisfied.
LED Indicators and Buttons
The touch pad has buttons for MODE,FAN,
POWER,SETPOINT UP and SETPOINT DOWN.
It also has LEDs that correspond to the mode,
fan speed,power and setpoint operation,to
indicate the unit s status.LEDs for HIGH,MED
,
and LOW indicate the fan speed that is selected.
LEDs for FAN,COOL and HEAT indicate what
operating mode is active.LED for POWER is the
unit ON/OFF status LED.If the unit is in ON mode,
the LED will be green.If the unit is OFF,the LED
will be off.
NOTE: HEAT mode is for Cooling & Heating models only.
Automatic Evaporator Freeze Protection
Automatically to keep the evaporator from
freezing,the compressor is tuuned off and the
indoor fan is turned on when the evaporator
temperature is too lower.If the evaporator
temperature is not too lower this function is off.
6
High Temperature Protection In Heating
Operation
The compressor and(or) electric heater will be
switched off to prevent damage in high indoor
blow air temperature or error indoor temperature
sensor.
Unit Configuration
O
F or OC
The unit can display in either OF or OC.
CONTROL PANEL OPERATION
The control panel keypad will look like the following
Fig.1. For some models with REMOTE SIGNAL
RECEPTOR, the unit can be controlled by the control
panel alone or by the remote. NOTE: Some models
have no REMOTE SIGNAL RECEPTOR.
Fig.1
POWER
- Press the POWER button to turn the unit on or off.
MODE
- Push this button to cycle through the modes from
COOL-HEAT-FAN-COOL.The indicator light beside
the "MODE" option will illuminate, identifying the
mode selected.
- COOL:.Cooling begins automatically when the
room temperature is above the set point,and stops
when the room temperature is 2OC(4OF) below the
set point.But the compressor will run 5 minutes at
least in COOL mode before stoping.
- HEAT:The maximum temperature can be set up to
29OC/84OF. For heat pump models,the unit can
alternate to run between in reverse cycle heat
mode and electric heater mode according to the
difference between the setting temperature and
the room temperature.
The fan motor cycles with the compressor stop.
NOTE:
The reverse cycle and electric heater cannot be run at
the same time. In following cases, it is normal that the
reverse cycle does not operate.
1.When the outdoor temperatrue is lower than 4OC/40OF
or the room temperature falls to 4.5OC/8OF below the
set point temperature.
2.There is a 3-minute minimum compressor run time at
any setting to prevent short cycling. The indoor fan
motors starts before the compressor and stops after
the compressor cycles off.
3.Push the S1 on the DIP SWITCHES to UP (ON)
position.
4.When frost builds up to the evaporator coils,the unit
will defrost automatically and the compressor will cycle
off.
- FAN:Fan operation only without heating and cooling.
Note: If the unit has DIP SWITCHES feature,the
temperature range can be setted is controlled by
DIP SWITCHES.See DIP SWITCHES CONFIGURATIONS on page 8 for details.
7
UP/DOWN BUTTONS (
/
)
- Push the UP (or DOWN) button to increase (or
decrease) the set temperature of the unit in cooling
or heating mode.The temperature can be set by
increments of 1OC (1OF).The setting temperature
appears in the display.
NOTE:Press and hold
and
buttons together
for 3 seconds will alternate the temperature display
between OC & OF scale.
FAN (FAN SPEED)
- Every time you push this button,the fan speed
cycles through the settings as follows:HIGH-MEDLOW-HIGH.
CONSTANT FAN
- In cooling mode, press the button to turn on or off the
constant fan function. When the function is turned on,
the constant fan light will illuminate, identifying the fan
continuous run for cooling. When the function is turnd
off, the constant fan light will go out, identifying the fan
cycle run with compressor stop.
NOTE: Every time the unit is turned on, the function
will work as the DIP SWITCHES CONFIGURATIONS
DISPLAYS:
- Shows the set temperature in OC or OF. While on
Fan only mode,it shows the room temperature.
Control code (on some models):
LC-Pads on the control panel is not available.The
unit can be setted by using wire cotroller only.
FC-Pads on the control panel and wire controller
are not available. The unit can be setted by
using FRONT DESK CONTROL only.
Error codes:
AS-Room temperature sensor error;
ES-Evaporator temperature sensor error;
CS-Condenser temperature sensor error;
OS-Outside temperature sensor error;
HS-Exhaust temperature sensor error;
LE-Wire cotroller error;
NOTE:When error occurs,unplug the unit and plug
it back in.If error repeats, call for service.
Other codes:
LO-Room temperature is lower than 0OC/32OF;
HI-Room temperature is higher than 37OC/99OF;
FP-Low temp. Protection.
NOTE: All the illustrations in this manual are
for explanation purpose only. Your air
conditioner may be slightly different.
The actual shape shall prevail.
CONTROL PANEL OPERATION CONTINUED
Accessory
NOTE:This air conditioner is designed to be
operated under condition as follows:
Cooling Outdoor temp:
operation
Indoor temp:
Heating Outdoor temp:
operation Indoor temp:
18-43OC/64-109OF (18-52OC/64-125OF
for special tropical models)
THIS UNIT IS CONTROLLED BY WALL MOUNTED THERMOSTAT
17-32 C/62-90OF
-5-24 C/23-76OF
O
0-27 C/32-80 F
O
O
NOTE:When the unit displays LC (Pads on the
control panel is not available.The unit can be setted
by using wire cotroller only.) You can install the
Accessory on the control panel.
O
Note: Performance may be reduced outside of
these operating temperatures.
NOTE: For some models, there is corresponding
operation happened after 3 seconds when pressing
any button.
NOTE: When there are wide differences between
USERS MANUAL and Remote controller Illustration
on function description, the description on USERS
MANUL shall prevail.
DIP SWITCHES CONFIGURATIONS (Optional)
X
A0A3
1 2 3 4
S9
1 2
S11
S1
S2
S3
S4
Fig.4
S5
S6
1 2 3 4
S7
1 2 3 4
S8
REMOVING THE FRONT PANEL
- Dip switches controls are located behind front panel,
through an opening below the control panel.To
access,remove front panel.See Fig.2.
- Dip switches are accessible without opening the
control box.See Fig.3.
- Unit must be powered OFF to effectively change
their status.
- Pull out at the bottom to release it from the tabs
DIP SWITCHES CONFIGURATIONS
- Then lift up .
- See Table 1 and Fig.4 for Dip Switches configurations
Fig.2
and functions of each dip switch position.
UP(ON)
DOWN(OFF)
Dip Switches
Wall thermostat type
Load delay for 3 seconds
Heating type
Temperature display type
Control type
Setpoint limit 1
Setpoint limit 2
Fan CON/CYC for heating
Fan CON/CYC for cooling
Low temp. Protection
8
Fig.3
.
DIP SWITCHES CONFIGURATIONS (Optional)
Table 1
No .
S1
S2
S3
UP(ON)
Electric Heat Only
Temperature Display in OF
Wall Thermostat Enable
DIP SWITCHES CONFIGURATIONS
DOWN(OFF)
Electric Heat and Pump Heat
Temperature Display in OC
Control Panel Enable
UP*UP:61OF~86OF(16OC~30O C);
S4*S5 UP*DOWN:65OF~78OF(18OC~26O C);
Two configurations (S4*S5)
combine to select set point
range.
DOWN*UP:63OF~80OF(17OC~27O C);
S6
DOWN*DOWN:68OF~75OF(20OC~24O C);
Fan Continuous Run for Heating Fan Cycle for Heating
S7
Fan Continuous Run for Cooling
S8
Low temp. Protection enable
Use some types of wall
S9
(S3 UP) Thermostat
S9
Use Control Panel only
(S3
DOWN)
Sw11
Remarks
For Heat Pump unit only
Load delay for 3 seconds
Fan Cycle for Cooling
Low temp. Protection disable Optional
you can consult with the
Use PTAC other Wall
sales agency or manufacturer
Thermostat
for details
Use Control Panel or some
types of wall Thermostat
Use control Panel or some
types of wall Thermostat, the
other one must be turned off
Normal
Optional
Electric Heat Only (for heat pump unit only)
- This setting is typically used for Emergency Heating.
Heat and Cool Fan CON/CYC Dip-switches
- Allows the fan to operate in continuous or cycle
modes while the unit is in heating and cooling mode.
NOTE: On heating mode, the setting temperature
can not be higher than 29OC/84OF.
Wall Thermostat Enable
- A wired wall thermostat can be connected to the
unit .If it is,this dip switch must be moved to the
Wall Thermostat Enable Position,before the wall
thermostat will begin control.
Low temp. Protecton(optional)
- If unit senses a room temperature below 32OF
(0OC), the fan motor and electric strip heat will
turn on and warm the room to 40OF(4.4OC). The
fan stops a short time after the temperature is
satisfied.
CON(Continuous)
-Allows fan to run continuously,circulating air even when the
temperature setting has been satisfied.This switch helps to
maintain the room temperature closer to the thermostat setting.
CYC(Cycle)
-This setting allows the fan to cycle on and off with the
compressor or electric heater.The fan stops a short time after
the temperature setting is satisfied.
Setpoint Temperature Limits
- Provides a restricted range of temperature control.
9
DIP SWITCHES CONFIGURATIONS by PANEL CONTROL
(Optional)
DIP SWITCHES CONFIGURATIONS by PANEL
CONTROL
- Turn off the unit.
- Press the up ( ) and down ( ) buttons together
for 3 seconds to activate the dip switches
configurations by panel control (see Fig.4).
- See Table 1 for Dip Switches configurations and
functions by panel control.
NOTE: Press the up ( ) and down ( ) buttons
together for 3 seconds again or no operation
within 30 seconds to exit the dip switches
configurations by panel control and the unit will
save the last settings.
- Display function settings with 2 digitals in LED
display window, high (left) for dip switches,
low (right) for functions (see Fig.4).
- Press up ( ) button to set the dip swithces, press
down ( ) button to set the functons.
Table 1
LED display window
High(left) Low(right)
01
Fig.4
DIP SWITCHES CONFIGURATIONS by PANEL CONTROL
Low(right)
No . High(left)
1-by
panel
control
0-by dip switches
/
0
1-electric heat only
0-electric heat and pump heat
1
S1
S2
1-tmperature display in OF
0-temperature display in OC
2
3- use control panel or some types of wall thermostat;
S3*S9 3
2-use some types of wall thermostat; 1-use PTAC other
wall thermostat; 0-control panel enable.
Remarks
For Heat Pump unit only
You can consult with the sales
agency or manufacturer for details
S4*S5
4
4-62OF~86OF(17OC~30OC); 3-61OF~86OF(16OC~30OC);
O
O
O
O
2-65OF~78OF(18OC~26OC); 1-63 F~80 F(17 C~27 C);
0-68OF~75OF(20OC~24OC);
S6
6
1-fan continuous run for heating 0-fan cycle for heating
S7
7
1-fan continuous run for cooling
0-fan cycle for cooling
S8
8
1-low temp. protection enable
0-low temp. protection disable
SW7
A
1-front desk control disable
0-front desk control enable
Optional
Optional
Sw11
B
1-Load delay for 3 seconds
0-normal
Optional
Not available for use PTAC
other wall thermostat .
NOTE:
1. The LED display window will show 00 when you first enter the setting mode, only when you set 01 you can start
the next settings.
2. To activate front dest control function, you need to pull the dip switch SW7 to DOWN(OFF) , and then set the panel
control to A0 .
3. After all set, press up ( ) and down ( ) buttons together for 3 seconds to exit the operation interface and cut off the
power. When re-power on, the settings are activated.
10
WALL THERMOSTAT TERMINAL (Optional)
IMPORTANT: Only trained, qualified personnel
should access electrical panel on unit and install
electrical accessories. Please contact your local
electrical contractor, dealer, or distributor for
assistance.
Thermostat Wire Routing
Thermostat wire is field supplied. Recommended
wire gauge is 18 to 20 gauge solid thermostat wire.
NOTE: It is recommended that extra wires are run
to unit in case any are damaged during installation.
Thermostat wire should always be routed around
or under, NEVER through, the wall sleeve. The
wire should then be routed behind the front panel
to the easily accessible terminal connector.
- Insert the wire connector of the wall thermostat into
the relevant terminal according to different shapes as
shown below.
Terminal of some types of wall
thermostat
Dip switch
Installation instruction of PTAC other Wall
Thermostat
- Remove the two screws as shown below and take
the cover panel down.
Remove the two screws
Take the cover panel down
Terminal of PTAC other Wall
Thermostat
NOTE: Refer to thermostat installation instructions
for details on installing wall thermostat.
Installation instruction of some types of wall
Thermostat (you can Consult with the
sales agency or manufacturer for details)
- Pull the dip switch to the DOWN(OFF) position as
shown below.
Dip switch
11
TERMINAL
24V(L)
24V(N)
COMP
HEAT1
HEAT2
4-WAY
HI-FAN
Fig. A - Proper Wire Routing Beneath Unit
LOW-FAN
FC(L)
THERMOSTAT WIRE ROUTING
(UNDER SLEEVE, BEHIND FRONT PANEL)
FC(N)
Terminal of PTAC other Wall Thermostat(MODE A)
DESIGNATION
FC(L)
Front desk control terminal L
FC(N)
Front desk control terminal N
LOW-FAN
Low fan speed
HI-FAN
High fan speed
4-WAY
4-way valve; Reverse cycle (Energized in
Heat) For heat pump models
HEAT2
Electrical heater 2
HEAT1
Electrical heater 1
COMP
Compressor
24V(N)
24VAC terminal N(Neutral),Common
24V(L)
24VAC terminal L
WALL THERMOSTAT TERMINAL (Optional)
FRONT DESK CONTROL
The controller can handle a switch signal from
FC(L) and FC(N) input, called front desk control.
Input must be 24VAC. If system doesn't receive
a 24VAC signal, it will turn unit off; otherwise, the
unit runs in normal control.
- The DIP switch can control the FRONT DESK
CONTROL feature. The DIP switch is on the DOWN
position, the unit will be turn off; otherwise,the unit
runs in normal control. See FigB.
4-WAY
HEAT1
COMP
24V(L)
24V(N)
LOW-FAN
HI-FAN
Terminal of PTAC other Wall Thermostat(MODE B)
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may
result in equipment damage or
improper operation.
Improper wiring may damage unit
electronics.Common busing is not
permitted. Damage or erratic
operation may result.
Dip switch of FRONT
DESK CONTROL
FigB.
NOTE:
Use terminal 4-way for heat pump connection
only.
Suggest set the compressor protection time
morn than 3 minutes in wall thermostat. If set less
than 3 minutes, the compressor will restart delay
3 minutes still.
Wall thermostat must be heating changeover
4-way valve.
For thermostats that have only one fan speed
output (on or auto),the fan speed is determined
by how the terminal connector is wired. If Low
fan is desired, wire the G output from the
thermostat to (LOW-FAN) on the units terminal
block. If High fan is desired, wire the G output
from the themostat to (HI-FAN) on the units
terminal block.
The range of set tempreture of Wall thermostat
must be in consonance with the range of DIP
switch setting.
Wall thermostat must be set the type properly
in consonance with the unit type : heat pump
or no heat pump.
If the Wall thermostat has only one electrical
heater output, connect the two terminals of
HEAT 1 and HEAT 2, the unit can operate two
electrical heaters(only for the unit has two
electrical heaters). Otherwise operate one
electrical heater.
Please do not remove the control panel.
12
INSTALLATION
HOW TO INSTALL THE UNIT
Dimension of air conditioner
CAUTION
1067mm/42inch
There are sharp edges that can cause
serious cuts.
When lifting the air conditioner,it is
HEAVY.Use 2 people to lift.
408mm/16inch
- For existing sleeve,you should measure the wall
sleeve dimensions.
- Install the new air conditioner according to these
installation instructions to achieve the best performance.
All wall sleeves used to mount the new air conditioner
must be in good structural condition and have a rear
grille that securely attaches to the sleeve or the flange
of the sleeve to secure the new air conditioner.
- To avoid vibration and noise,make sure the unit is
installed securely and firmly.
- When installing the sleeve,make certain there is
nothing within 20 of the back that would interfere
with heat radiation and exhaust air flow. (See Fig.5)
COOLED
AIR
WALL
606mm/23.9inch
Dimension of sleeve assembly (optional)
1067mm/42inch
408mm/16inch
376mm/14.8inch
SLEEVE
HEAT
RADIATION
Shipping
tape
Over 20
INTAKE
AIR
Fig.6
WALL
Fig.5
PREPARATION OF SLEEVE ASSEMBLY(optional)
- Refer to the installation instruction of sleeve assembly
for details.
PREPARATION OF REAR GRILLE ASSEMBLY
(optional)
- Refer to the installation instruction of rear grille
assembly for details.
- Pull out at the bottom to release it from the tabs
- Then lift up .
Fig.7
UNIT INSTALLATION
- Carefully remove shipping tapes from the front panel.
(See Fig.6)
- Remove the front panel. (See Fig.7)
- Remove the shipping screw from the vent door.(See
Fig.8)
13
Shipping
screw
Fig.8
.
INSTALLATION
UNIT INSTALLATION (CONTINUED)
- Rotate the vent control lever to either open or close
the vent door.(See Fig.9)
Vent control lever
CONTINUED
CAUTION
Do not put obstacles around air-inlet
or inside of air-outlet of the unit,
such as window curtain etc.
Always insert the filter securely, clean
filter once every two weeks as r
equired.
Vent closed
Vent open
Fig.9
NOTE:When vent control lever set at CLOSE,only
the air inside the room is circulated and filtered.
When set at OPEN,some outdoor air will be drawn
into room.This will reduce heating or cooling
efficiency.
- Lift unit level and slide unit into wall sleeve until
firmly against front of wall sleeve and secure with
4 screws and washers (supplied in the SLEEVE
ASSEMBLY ) through the unit flange holes.
(See Fig.10 and Fig.11)
Fig.10
Fig.11
- Reinstall front panel.(See Fig.12)
Place tabs over top rail . Push Inward at bottom
until panel snaps into place
.
Fig.12
14
CARE AND CLEANING
FRONT PANEL AND CASE
- Turn unit off and disconnect power supply.To clean,
use water and a mild detergent.DO NOT use bleach
and abrasivers.Some commercial cleaners may
damage the plastic parts.
OUTDOOR COIL
- Coil on outdoor side of unit should be checked
regularly.Unit will need to be removed to inspect
dirt build-up that will occur on the inside of the coil.
If clogged with dirt and soot ,coil should be
professionally cleaned.Clean inside and outside of
outdoor coils regularly.
NOTE: Never use a high-pressure spray on coil.
CAUTION
- Removing Air Filter
2 Air filters
Pull up
Fig.13
- Replacing Air Filter
Push down
UNIT DAMAGE HAZARD
Failure to follow this caution may result in
equipment damge or improper operation.
Airflow restriction may cause damage to
the unit.
Fig.14
VENT DOOR FILTER
IMPORTANT:TURN UNIT OFF BEFORE
CLEANING.
AIR FILTERS
IMPORTANT:TURN UNIT OFF BEFORE
CLEANING.
CAUTION
UNIT DAMAGE HAZARD
Failure to follow this caution may result in
equipment damge or improper operation.
Do not operate unit without filters in
place.If a filter becomes torn or damaged,
it should be replaced immediately.
Operating without filters in place or with
damaged filter will allow dirt and dust to
reach indoor coil and reduce cooling,
heating,airflow and efficiency of unit.
Airflow restriction may cause damage
to unit.
- The most important thing you can do to maintain
unit efficiency is to clean the filters once every
two weeks as required.
Clogged filters reduce cooling,heating and airflow.
- Keeping filters clean will:
Decrease cost of operation.
Save energy.
Prevent clogged indoor coil.
Reduce risk of premature component failure.
- To Clean Air Filters:
Vacuum off heavy soil.
Run water through filter.
Dry thoroughly before replacing.
- If the vent door is open,access requires the removal
of the unit from the wall sleeve.Clean the vent filter
twice a year or as required.
- Make sure to remove the shipping screw from the
vent door.(See.Fig.8)
- Rotate the vent control lever to open the vent door.
(See. Fig.15)
- Remove four screws from the vent door filter.
(See.Fig.15)
- First pull out the vent door steel wire from the hole
of the vent door, then take off the vent door and filter.
(See.Fig.15)
- Clean the filter.Dry thoroughly before replacing.
- Replac the vent door and filter,reinstall the four
screws.
- Reinsert the vent door steel wire into the hole of the
vent door.
Vent door
control lever
.
Screws
Vent door
steel wire
Vent door
filter
Fig.15
15
Vent door
TROUBLESHOOTING
POSSIBLE CAUSES
SOLUTONS
UNIT DOES NOT START
Unit may have become unplugged
Fuse may have blown
Circuit breaker may have been tripped
Unit may be off
Unit may be in a protection mode.
Check that plug is plugged securely in wall receptacle.
Note:Plug has a test/reset button on it.Make sure that the plug has
not tripped.
Replace the fuse.See Note 1.
Reset circuit breaker.See Note 1.
Turn unit on (bottom right button on keypad).
UNIT NOT COOLING/HEATING ROOM
Unit air discharge section is blocked
Temperature setting is not high or low
enough
Note:Setpoint limits may not allow the
unit to heat or cool the room to the
temperature desired.Check section on
dipswitch settings.
Unit air filters are dirty.
Room is excessively hot or cold when
unit is started.
Vent door left open.
Unit may be in a protection mode.
Compressor is in time delay.
Make sure that curtains,blinds or furniture are not restricting or
blocking unit airflow.
Reset to a lower or higher temperature setting.
Remove and clean filters.
Allow sufficient amount of time for unit to heat or cool the room.
Start heating or cooling early before outdoor temperature,cooking
heat or gatherings of people make room uncomfortable.
Close vent door.
Check dipswitch and wall thermostat settings for desired comfort.
Wait approximately 3 minutes for compressor to start.
DISPLAY HAS STRANGE NUMBERS/
CHARACTERS ON IT
The unit may be in a protection mode.
The unit may be set for OC (instead of OF).
UNIT MAKING NOISES
Clicking,gurging and whooshing noises are normal during
operation of unit.
WATER DRIPPING OUTSIDE
If a drain kit has not been installed,condensation runoff during very
hot and humid weather is normal.See Note 2.If a drain kit has been
installed and is connected to a drain system,check gaskets and
fittings around drain for leaks and plugs.
WATER DRIPPING INSIDE
Wall sleeve is not installed level
Wall sleeve must be installed level for proper drainage of
condensation .Check that installation is level and make any
necessary adjustments.
16
TROUBLESHOOTING
POSSIBLE CAUSES
SOLUTONS
ICE OR FROST FORMS ON INDOOR
COIL
Low outdoor temperature
Dirty filters
When outdoor temperature is approximately 55OF or below,frost
may form on the indoor coil when unit is in Cooling mode.Switch
unit to FAN operation until ice or frost melts.
Remove and clean filters.
COMPRESSOR PROTECTION
Power may have cycled,so compressor
is in a restart protection.
Random Compressor restart-Whenever the unit is plugged in,or
power has been restarted,a random compressor restart will occur.
After a power outage,the compressor will restart after
approximately 3 minutes.
Compressor Protection-To prevent short cycling of the compress
or, there is a random startup delay of 3 minutes and a minimum
compressor run time of 3 minutes.
ELECTRIC HEATING FAILURE
Clean the evaporator once every three months by professional
people.
NOTES:
1.If circuit breaker is tripped or fuse is blown more than once,contact a qualified electrician.
2.If unit is installed where condensation drainage could drip in an undesirable location,an accessory drain kit
should be installed and connected to drain system.
17
The Klimaire logo is a registered Trademark of Klimaire Products inc.
Copyright 2020 Klimaire Products Inc.
2190 NW 89 Place, Doral, FL 33172 - USA
The design and specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement