Air King 4DA35B/9102B Operating Instructions & Parts Manual
Advertisement
Advertisement
Parrilla
Posterior
Girador
Tuerca de
Plástico
Parrilla
Anterior
4DA35B/9102B y 4DA36B/9106B
ENSAMBLADO
1. Incline el cabezal del ventilador hacia atrás. Coloque la Parrilla
Plástica Posterior en el Motor. (Figura 1)
2. Alinee el corte triangular en “∆” en la Parrilla Plástica Posterior con el poste triangular en la parte superior de la cubierta frontal del Motor. Encaje totalmente la Parrilla Plástica Posterior y fíjela con la Tuerca de Plástico, haciéndola girar en el Sentido de las Manecillas del Reloj. (Figura 2)
3. Deslice la Hélice sobre el Eje del Motor. (Alinee la Ranura en el bloque de la hélice con la Clavija del eje del motor.) (Figura 3)
4. Para fijar la Hélice, atornille el Girador en el Eje en el
Sentido Contrario a las Manecillas del Reloj hasta que se encuentre fija en el cubo de la hélice.
5. Con el cabezal del ventilador en posición recta, alinee el
Ornamento de la Parrilla Anterior para que quede en posición horizontal. Inserte la parte inferior de la Parrilla Anterior dentro de la Parrilla Plástica Posterior. La Lengüeta en la parte inferior de la Parrilla Plástica Posterior debería encajar entre los rayos de la
Parrilla Anterior. Encaje la Parrilla Anterior dentro de la Parrilla
Plástica Posterior comenzando desde arriba y progresando en forma descendiente por ambos lados.
Figura 1
Hélice
Parrilla
Posterior
Figura 2
Ranura
Motor
Espiga
Figura 3
Clavija
FUNCIONAMIENTO
OSCILACIÓN VARIABLE: Jale la perilla de oscilación ubicada en la parte posterior del motor hacia arriba. Gire el cabezal del ventilador hacia la izquierda, derecha o hacia delante. Empuje la perilla de oscilación hacia abajo y el ventilador oscilará describiendo el
ángulo fijado.
ÁNGULO VERTICAL: Para ajustar el ángulo vertical, incline el cabezal del ventilador hacia arriba o abajo, según prefiera.
VELOCIDAD: La velocidad está controlada por una perilla rotatoria:
(0) Apagado, (3) Alta, (2) Media, (1) Baja.
CABLE ELÉCTRICO: Enchufe el cable eléctrico en un tomacorriente de pared (CA 120 Voltios, 60 Hz).
MANTENIMIENTO
ADVERTENCIA:
SIEMPRE DESENCHUFE EL CABLE ANTES
DE MOVER O DAR SERVICIO AL VENTILADOR.
ADVERTENCIA:
¡NO SUMERJA EL VENTILADOR EN AGUA!
LIMPIEZA: Utilice un paño suave humedecido con una solución jabonosa liviana, tal como un detergente líquido para lavar platos.
Seque TODAS LAS PARTES POR COMPLETO antes de rearmar.
Después de dar mantenimiento o servicio, REARME POR COMPLETO la unidad en la forma descrita en este manual de instrucciones, antes de volver a conectarla a la fuente de poder.
PRECAUCIÓN:
No utilice gasolina, bencina, acetona, limpiadores abrasivos, etc. puesto que dañarán el Ventilador.
NUNCA use ALCOHOL O SOLVENTES.
LUBRICACIÓN: Los cojinetes de precisión vienen sellados de por vida en la fábrica y no precisarán ninguna lubricación adicional.
ALMACENAMIENTO: Guarde el Ventilador con estas instrucciones en un lugar fresco y seco.
REPARACIONES: Cualesquiera otras reparaciones, con la excepción del mantenimiento general a cargo del usuario, deben ser realizadas por un representante de servicio autorizado.
1
4
3
6
16
15
7
5
2
9
Figura 3
14
13
17
12
LISTA DE REPUESTOS
NO. DE PARTE PARA EL MODELO
REF DESCRIPCIÓN 4DA35B/9102B 4DA36B/9106B CANT .
1 Motor
2 Interruptor
3 Plastico Protector
02035053
02055087
02035052
02055087
7091854 7091854 1
4 Resorte de elevaci 02090586 1
1
1
5
6
7
8
9
Placa de trinquete
Eje de elevación
Base
Perilla del Interruptor
10 Placa Inferior
02010162B
02090521
Tuerca hexagonal de 5/16-24 02090033
2010540P
2010131
2010313
02010162B
02090521
02090033
2010541
2010131 1
1
1
1
1
1
11 Cordón eléctrico con clavija 02050009FPB 02050009FPB 1
12 Rejilla frontal 02096217
2010315
020962141 1
13 Tapa
14 Aspa
15 Tuerca de plastica
2010093
2010008
2010359P
2010093
2011013
2010359P
1
1
1
16 Rejilla plastica trasera
17 Ornamento de la rejilla
18 Pata de caucho
19 Tornillo #8 X 9/16 PPH
2011212
02010381A
2010415
2090039
2011200M
02010381A
2010415
2090039
2
1
1
1
11
18
Rev. F 10/09
10
19
8
4 2084067
OPERATING INSTRUCTIONS & PARTS MANUAL
OSCILLATING FANS
12" (30,5 cm) MODEL 4DA35B/9102B
16" (40,6 cm) MODEL 4DA36B/9106B
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DE-
SCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY
WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
DESCRIPTION
The Air King ® 12" (30,5 cm) and 16" (40,6 cm) Oscillating Fans feature whisper quiet operation with a 3 paddle blade. Fan is powered by a pre-lubricated permanent split capacitor motor with a 6 ft. (1.8 m)
18/3 cord set. Fan grills meet OSHA requirements. ETL listed.
SPECIFICATIONS
Motor ........................................120V, 60Hz (12")(30,5 cm)
CFM
M 3 /s
RPM
Amps
Watts
dB (A)
930
0.43
0.40
39
45
780
35
41
120V, 60Hz (16")(40,6 cm)
Blade Size ................................12" (30,5 cm) Model(4DA35B/9102B)
16" (40,6 cm) Model(4DA36B/9106B)
Speeds .....................................3 Speeds
Control .....................................Rotary Knob
Air Flow Distribution ................90°
MODEL 4DA35B/9102B 4DA36B/9106B
SPEED HIGH MED LOW HIGH MED LOW
620
32
36
1710 1500 1330
0.37 0.29 0.80
0.30 0.27 0.71
77
53
0.71 0.63
1450 1300 1090 1545 1394 1244
0.54 0.48
65
49
57
44
GENERAL SAFETY INFORMATION
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and injury to person, including the following:
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electrical requirements of the Fan.
3. Use this Fan only as described in this manual. Any other use not recommended by the manufacturer may cause fire, electrical shock, or injury to persons.
4. Unplug power cord before installing, servicing, or moving the Fan.
WARNING:
DO NOT DEPEND UPON THE ON-OFF
SWITCH AS THE SOLE MEANS OF DISCONNECTING
POWER WHEN INSTALLING OR SERVICING THE FAN.
ALWAYS UNPLUG THE POWER CORD.
5. This Fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden or wet atmospheres.
6. DO NOT use Fan in or near a window. Rain may create an electrical hazard.
7. The power cord is equipped with a three-prong grounded plug that must be inserted into a matching receptacle. Under no circumstances should the grounding prong be cut off the plug.
Where a two-prong wall receptacle is encountered, it must be replaced with a properly grounded three-prong receptacle installed in accordance with the National Electrical Code (NEC) and all applicable local codes and ordinances. This work must be done only by a qualified electrician, using
copper wire only.
WARNING:
USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNEC-
TION MAY CREATE THE RISK OF ELECTROCUTION. USE
OF SUCH ADAPTERS IS NOT PERMITTED IN CANADA.
WARNING:
THIS PLUG IS A SAFETY FEATURE. TO
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK AND
PERSONAL INJURY, DO NOT REMOVE, REPLACE, REPAIR
OR TAMPER WITH THE ORIGINALLY SUPPLIED PLUG. IF
THE FAN DOES NOT FUNCTION PROPERLY, IT MAY BE
DUE TO THE SAFETY DEVICE INCORPORATED IN THIS
PLUG.
8. Where possible, avoid the use of extension cords. If they must be used, minimize the risk of overheating by ensuring that they are UL listed. Never use a single extension cord to operate more than one Fan.
9. DO NOT operate any Fan with a damaged cord or plug or after the Fan malfunctions, has been dropped or damaged in any manner.
10.DO NOT insert or allow fingers or foreign objects to enter any ventilation or exhaust opening as it may cause an electric shock or fire, or damage the Fan. DO NOT block or tamper with the
Fan in any manner while it is in operation.
11.Always place the Fan on a stable, flat, level surface when operating, to avoid the chance of the Fan overturning. Locate the Power Cord so the Fan or other objects are not resting on it.
DO NOT run Power Cord under carpeting. DO NOT cover Power
Cord with throw rugs, runners, or the like. Arrange Power Cord away from room traffic and where it will not be tripped over.
12.This Fan is NOT intended for use in wet or damp locations.
Never locate a Fan where it may fall into a bathtub or other water container.
13.DO NOT use Fan outdoors.
14.This Fan is NOT suitable for use in agricultural facilities including areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating to electrical requirements for Agricultural Buildings. THIS FAN
DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE
547-7 (2008).
15.This Fan is NOT suitable for use in hazardous locations. Please refer to National Electric Code (NEC) Article 500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations. THIS FAN DOES NOT MEET THE
REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING:
REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK – DO NOT USE THIS FAN WITH ANY SOLID STATE
SPEED CONTROL DEVICES.
SAVE THESE
INSTRUCTIONS
Rev. F 10/09 1 2084067
4DA35B/9102B and 4DA36B/9106B
ASSEMBLY
1. Tilt Fan Head back. Put Plastic Rear Grill on Motor. (Figure 1)
2. Align Triangular "∆" cut in Plastic Rear Grill with triangular post on top of front Motor cover. Fully seat Plastic Rear Grill and secure with Plastic Nut turning Clockwise. (Figure 2)
3. Slide Blade onto Motor Shaft. (Align groove on blade hub with pin on motor shaft.) (Figure 3)
4. To secure Blade, screw Spinner onto Shaft Counter
Clockwise until tight on blade hub.
5. With fan head in upright position, align Ornament of Front Grill so it is horizontal. Insert bottom of Front Grill into Plastic Rear
Grill. Tab at the bottom of Plastic Rear Grill should fit between spokes of Front Grill. Snap Front Grill into Plastic Rear Grill beginning at the top and working down both sides.
OPERATION
VARIABLE OSCILLATION: Pull oscillation knob on the rear of the motor up. Turn fan head to left, right, or straight ahead. Push oscillation knob down and fan will oscillate about the set angle.
VERTICAL ANGLE: To adjust vertical angle, tilt fan head up or down, as desired.
SPEED: Speed is controlled by a rotary knob. (0) Off, (3) High, (2)
Medium, (1) Low.
POWER SUPPLY CORD: Plug power supply cord into a wall outlet
(AC 120Volts, 60 Hz).
Plastic
Rear Grill
Blade
Figure 1
Plastic Nut
Spinner
Front
Grill
Plastic Rear
Grill
Figure 2
Groove
Motor
Pin
Figure 3
Pin
MAINTENANCE
WARNING:
ALWAYS UNPLUG THE CORD BEFORE MOVING
OR SERVICING THE FAN.
WARNING:
DO NOT IMMERSE FAN IN WATER!
CLEANING:
Use a soft cloth moistened with a mild soap solution, such as liquid dish washing detergent. Dry ALL PARTS COM-
PLETELY before reassembling. After any maintenance or servicing, completely reassemble unit as described in this instruction manual before reconnecting to the power supply.
CAUTION:
Do not use gasoline, benzine, thinner, harsh cleaners, etc. as they will damage the Fan. NEVER use ALCOHOL
OR SOLVENTS.
LUBRICATION: Precision bearings are sealed at the factory for life and will not require any further lubrication.
STORAGE: Store the Fan, with these instructions, in a cool, dry place.
SERVICING
:
All other servicing, with the exception of general user-maintenance, should be performed by an authorized service representative.
Figure 3
16
1
4
3
6
11
18
Rev. F 10/09
15
7
5
2
9
10
19
8
14
13
17
12
REPLACEMENT PART LIST
REF
PART NO. FOR MODEL
NO. DESCRIPTION 4DA35B/9102B 4DA36B/9106B Qty
QTY
.
1 Motor
2
3
4
Rotary Switch
Crimp Connect
Elevation Spring
5 Ratchet Plate
6 Neck Bolt
7 5/16-24 Hex Nut
8 Stand
9 Switch Knob
10 Bottom Plate
02035053
02055087
7091854
-
02010162B
02090521
02090033
2010540P
2010131
2010313
11 Power Supply Cord w/Plug 02050009FPB
12 Front Grill 02096217
13 Spinner
14 Fan Blade
2010093
2010008
15 Plastic Nut
16 Plastic Rear Grill
17 Grill Ornament
18 Rubber Foot
19 Screw #8 X 9/16 PPH
2010359P
2011212
02010381A
2010415
2090039
02035052
02055087
7091854
02090586
02010162B
02090521
02090033
2010541
2010131
2010315
02050009FPB
020962141
2010093
2011013
2010359P
2011200M
02010381A
2010415
2090039
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2 2084067
MANUAL DE INSTRUCCIONES DE OPERACIÓN Y PARTES
VENTILADORES OSCILANTES
MODELO 4DA35B/9102B 12" (30,5 cm)
MODELO 4DA36B/9106B 16" (40,6 cm)
DESCRIPCIÓN
ESPECIFICACIONES
Motor .........................................120V, 60Hz (12")(30,5 cm)
...................................................
Tamaño de paletas .....................
...................................................
VELOCIDAD ALTA MEDIA BAJA ALTA MEDIA BAJA
CFM
M 3 /s
RPM
Amps
Watts
dB A personas.
930
0.43
0.40
39
45
780
0.37
0.30
35
41 incluyenda las siguientes.
LEA Y GUARDE ESTAS INSTRUCCIONES
LÉALAS CUIDADOSAMENTE ANTES DE INTENTAR ARMAR, INSTALAR, OPERAR O DAR MANTENIMIENTO AL PRODUCTO DESCRITO.
PROTÉJASE A SÍ MISMO Y A LOS DEMÁS OBSERVANDO TODA LA INFORMACIÓN SOBRE SEGURIDAD. ¡NO SEGUIR LAS INSTRUC-
CIONES PODRÍA RESULTAR EN LESIONES PERSONALES Y/O DAÑOS A LA PROPIEDAD!
GUARDE LAS INSTRUCCIONES PARA REFERENCIAS FUTURAS.
Los Ventiladores Oscilantes Air King
Distribución del flujo de aire ....90˚
MODELO 4DA35B/9102B servicio o mover el Ventilador.
620 1710
0.29 0.80
0.27 0.71
32
36
® de 12” (30,5 cm) y 16” (40,6 cm) vienen equipados con un motor de funcionamiento silencioso y una hélice de tres aspas. El ventilador es potenciado por un motor capacitador de hendidura permanente y prelubricado con un cable eléctrico 18/3 de 6 pies (1.8 m) de largo. Las parrillas del ventilador cumplen con los requisitos de OSHA. Equipo aprobado por ETL.
120V, 60Hz (16")(40,6 cm)
12" (30,5 cm) Modelo (4DA35B/9102B)
16"(40,6 cm) Modelo (4DA36B/9106B)
Velocidades ..............................3 velocidades
Control ......................................Perilla Rotatoria
4DA36B/9106B
1450 1300 1090 1545 demandas eléctricas del Ventilador.
77
53
1500 1330
0.71
1394 1244
0.54
65
49
0.63
0.48
57
44
INFORMACIÓN GENERAL DE SEGURIDAD
Al usar aparatos eléctricos, las precauciones básicas de seguridad deberan siempre de seguirse para reducir el riesgo de incendio, choque eléctrico, y daño a personas,
1. Lea todas las instrucciones antes de utilizar el Ventilador.
2. Cerciórese de que la fuente de poder sea compatible con las
3. Use este Ventilador sólo en la forma que se describe en el manual. Cualquier otro uso no recomendado por el fabricante podría ocasionar un incendio, golpes de electricidad o lesiones a
4. Desenchufe el cable eléctrico antes de instalar, proporcionar
ADVERTENCIA: NO DEPENDA DEL INTERRUPTOR DE ENCENDIDO-
APAGADO COMO EL ÚNICO MEDIO PARA DESCONECTAR LA POTENCIA
AL INSTALAR O PROPORCIONARLE SERVICIO AL VENTILADOR.
DESENCHUFE SIEMPRE EL CABLE ELÉCTRICO.
5. Este Ventilador NO debe usarse en ubicaciones potencialmente peligrosas, tales como en ambientes inflamables, explosivos, cargados de sustancias químicas o húmedos.
6. NO use el Ventilador en o cerca de una ventana. La lluvia puede generar riesgos eléctricos.
7. El cordón eléctrico está equipado con una clavija a tierra de tres espigas que tiene que ser enchufada a un receptáculo del mismo diseño. Bajo ninguna circunstancia deberá cortarse la espiga a tierra de la clavija. De existir un receptáculo de pared de dos espigas, deberá reemplazarse por uno de tres espigas debidamente puesto a tierra e instalado de conformidad con el Código Nacional de Electricidad y todos los códigos y ordenanzas locales aplicables. El trabajo deberá hacerlo un electricista calificado, utilizando exclusivamente alambre de cobre.
ADVERTENCIA: NO SE RECOMIENDA EL USO DE UN ADAPTADOR DE
TRES A DOS ESPIGAS. LA CONEXIÓN INDEBIDA PODRÍA CREAR EL
RIESGO DE SER ELECTROCUTADO. EL USO DE TALES ADAPTADORES
NO ESTÁ PERMITIDO EN CANADÁ.
ADVERTENCIA: ESTE ENCHUFE ES UNA MEDIDA DE SEGURIDAD. PARA
REDUCIR EL RIESGO DE INCENDIO, CHOQUE ELÉCTRICO Y LESIONES
PERSONALES, NO QUITE, NI REEMPLACE, NI REPARE O ALTERE EL
ENCHUFE QUE SE PROVEE ORIGINALMENTE. SI EL VENTILADOR NO
FUNCIONA CORRECTAMENTE, PUEDE DEBERSE AL DISPOSITIVO DE
SEGURIDAD INCORPORADO EN ESTE ENCHUFE.
8. De ser posible, evite el uso de cables de extensión. Si debieran usarse, minimice el riesgo de sobrecalentamiento procurando que estén aprobados por UL. Nunca use un solo cable de extensión para hacer funcionar más de un Ventilador.
9. NO haga funcionar ningún Ventilador con un cable o enchufe dañado o después de que el ventilador presente algún desperfecto o haya sido dejado caer o sufriera cualquier tipo de daño.
10.NO introduzca ni permita que se introduzcan dedos u objetos extraños en ninguna abertura de ventilación o escape, puesto que podría provocar un golpe de electricidad, incendio, o daños al ventilador. NO bloquee ni manipule el Ventilador de ninguna manera mientras esté en funcionamiento.
11.Siempre coloque el Ventilador sobre una superficie, estable, plana y horizontal mientras esté en funcionamiento, para evitar la posibilidad de que el Ventilador se dé vuelta. Ubique el cable eléctrico de tal modo que el ventilador u otros objetos no descansen sobre él. NO disponga el cable eléctrico debajo de alfombras. NO cubra el cable eléctrico con tapetes, alfombras continuas u objetos similares. Coloque el cable eléctrico fuera del paso de las personas y donde nadie se tropiece con el mismo.
12.Este Ventilador NO ha sido diseñado para usarse en lugares mojados o húmedos. Nunca coloque un Ventilador donde quepa la posibilidad de que caiga en una bañera u otro recipiente con agua.
13.No use el Ventilador en exteriores.
14.Este Ventilador NO es adecuado para usar en instalaciones de agricultura incluyendo áreas donde se almacene ganado, aves de corral u otros animales. Por favor consulte el Articulo
547-7 (2008) del Código Eléctrico Nacional (NEC), o los códigos o normas estatales o locales aplicables con relación a los requisitos eléctricos para edificios destinados a las agricultura.
ESTE VENTILADOR NO CUMPLE CON LOS REQUISITOS DEL
ARTICULO 547-7 DEL NEC (2008).
15.Este Ventilador NO es adecuado para usar en lugares peligrosos.
Por favor consulte el Artículo 500 del Código Eléctrico Nacional
(NEC), o los códigos o normas estatales o locales aplicables con relación a los requisitos eléctricos para lugares peligrosos.
ESTE VENTILADOR NO CUMPLE CON LOS REQUISITOS DEL
ARTICULO 500 (2008).
ADVERTENCIA: DISMINUYA EL RIESGO DE INCENDIO O GOLPES
DE ELECTRICIDAD – NO USE ESTE VENTILADOR CON ARTEFACTOS
DE CONTROL DE VELOCIDAD EN ESTADO SÓLIDO.
CONSERVE ESTAS
INSTRUCCIONES
Rev. F 10/09 3 2084067

Public link updated
The public link to your chat has been updated.
Advertisement