OPERATION MANUAL
for
MBM JT-7
Jogger
Keep this book in a safe place ready for quick reference. |
A PRODUCT OF
CORPORATION
1-800-223-2508
February 16, 2005
Introduction
Thank you very much for purchasing our product.
Please read this operation manual carefully to ensure correct product handling.
Before using the product, read "Tips for Safe, Correct Product Handling."
After reading, keep this manual for quick reference.
} ".
1. Safety Instructions (Be sure to observe these.)
The precautions that should always be observed to prevent physical harm to users or
others and property damage are emphasized in the formats described below.
- The extent of harm or damage that could result from improper handling of the product in
defiance of a specific action is designated by one of the following markings:
Danger Alerts users that failure to take or avoid a specific action could
result in death or serious injury.
: Alerts users that failure to take or avoid a specified action could
|, Caution | result in injury or property damage.
- The kinds of precautions to be observed are designated by these pictorial markings:
S This pictorial marking designates a prohibited action.
® Do not overhaul the product using tools.
Y Do not touch.
© This pictorial marking designates a compulsory action that must always be
performed.
——
& Disconnect the power plug.
E Connect the ground wire.
/\ This pictorial marking denotes a precaution.
/N High temperature caution
AN Danger
Do not place receptacles containing water on the
machine.
If water is spilled, it may cause fire or an
O
Do not put any foreign object, such as metal,
or inflammable thing inside the machine.
It may cause fire or an electrical shock.
melts and it may fire or an electric shock.
E electrical shock. Ri
Do not touch any revolving part of the machine Do not remove the machine cover, back
with a hand, or reach a hand into the machine. cover, etc.
at It may cause a bodily injury. sages There are parts with very high in voltage that
may cause an electrical shock.
Do not dismantle, remodel, or repair the machine. Do not use any other voltage than voltage and
It may cause fire, electrical shock, or bodily injury. cycle designated on the serial plate.
REIL tfepaitisirequined, contact your dealer 25+ Doing so could cause fire or an electrical
shock.
Do not put the machine close to heating Do not use inflammable spray inside or near
equipment. the machine for cleaning or the like.
The machine cover or the coating of power code or As gas, which fills the interior, it may ignite
and cause a fire or explosion.
Apply the power supply of the designated
voltage, and independently use the wall outlet
with a proper rated current specified in the
If dust is prongs or prong fitting part of the
power plug, wipe the dust off with a dry cloth.
It may cause fire.
## serial plate. e '
If the outlet is used concurrently with other
equipment, the branched part of the outlet could
overheat and cause fire.
Should any foreign substance, such as metal, Do not do anything that may damage the power
water, etc., get inside the machine, be sure to cord or power plug.
yw turn off the power first, and then disconnect the (Do not scratch, process, forcibly bend, twist, or pull
tic POWET plug from the outlet. IE it or place heavy object on it, or bundle it.)
If the machine is used as it is, it may cause fire or
an electrical shock. Doing so could cause a fire or an electrical shock.
Contact your dealer immediately.
When disconnecting the power plug from the Do not unplug the power plug with wet hands.
outlet, be sure to grip the plug itself.
It may cause an electrical shock.
26 Pulling the power cord may damage the cord, which
could cause a fire or an electrical shock. E
Be sure to turn off the power first and pull the
power plug from the outlet when cleaning the
_ machine.
The machine may be operated by mistake, causing
a bodily injury.
АК
$
7 —
IE
Be sure to connect a ground wire.
If an electric leak occurs, it may cause fire or an
electrical shock.
В /\ Саибоп
&
Place the machine on a level and stable table
or floor with enough space,
When the collator will not be used for several
days, such as during consecutive holidays,
etc, be sure to unplug the power cord from
2R737
the outlet for safety's sake. 286) — otherwise the machine may fall, which could result
ElR< E mba in bodily injury.
Due to deteriorated insulation, it may cause an
electric fire.
Do not place the machine in a humid place or Be sure to remove the power plug from the
where it could get wet. outlet when moving the machine,
Doing so could cause the insulation to deteriorate ER757 Otherwise it may damage the cord, causing fire or
RIE and cause an electrical shock or fire. £x< an injury
| _
2. Operating Notes
2.1 Power Supplies
The supply voltage range in which the product is guaranteed to provide unfailing
performance is as follows:
Voltage designated on the serial plate (+6%, -10%), 50/60 Hz
Insert the plug of the power cord directly into a wall socket.
2.2 Operating Environment
Use this product in places that are:
- Not exposed to direct sunlight.
- Free from significant dirt or dust.
- Free from significant vibrations.
- Free from significant salinity.
- Free from special chemicals.
2.3 Storage Conditions
Store this product in places that are:
- Not exposed to direct sunlight.
- Free from significant dirt or dust.
- Free from significant vibrations.
- Free from significant salinity.
- Free from special chemicals.
2.4 Machine Maintenance
To sustain satisfactory product performance, customers are advised to refrain from
lubricating and greasing the components of the product by themselves (unless
customer lubrication or greasing is otherwise recommended in this manual). If any
problems are observed, contact your dealer.
yo
3. Component Names and Functions
3.1 Main Unit
D
No. Name Function
À paper tray that vibrates to align paper. Load a stack of
@ | Paper tray paper to align in the tray by holding its top, with the edge facing
down.
Fixes the angle of the paper tray. With the paper tray held with
@ | Clamp lever one hand, loosen the clamp lever to adjust the tilt angle.
When the tray is located, fully tighten the lever.
© | Operation panel Turns the vibration function on and off.
; When the power switch is foot-operated, press down the foot
@ | Foot switch Switch to vibrate the paper tray.
Clamp lever
Cord inlet
— Power cord
3.2 Operation Panel
E
Conta
D
OF Fa
Footm
NTA
No. Name Function
When the switch is set to “Cont”, it starts jogging. When the
(M) | Power switch
switch is set to “Foot”, it makes the unit operable only when
the foot switch is pressed down.
Note: Be sure to set the power switch to the
intermediate OFF position when the work
completes or is paused.
@ | Fuse (3A)
Blows when the electrical circuit gets faulty.
} ba
4. Operating Instructions
| Adjusting the Tilt Angle of the Paper Tray |
- With the lower middle part of the control box (located back side of the paper tray) held
with one hand, loosen the clamp lever to adjust the tilt angle and locate the tray.
- Set the power switch to the OFF position before adjusting the tilt angle of
the paper tray. In adjusting the tilt angle of the paper tray, hold the lower
middle part of the control box (located back side of the tray). Holding the
part of the tray marked by — below could result in physical injury.
- Tighten the clamp lever firmly so the paper tray will not work loose during
operation.
„
Do not hold V-shaped jogging tray.
- Typically, the tilt angle of the paper tray should be set vertically for stiff paper and laterally
for soft paper.
Angle for jogging soft paper
How to align paper neatly |
- Press down the foot switch briefly to fine-tune the strength of the vibrating force.
- Hold the length of each stack of paper to 60 to 65 mm or below to align it after collating.
| Using the paper clamp board | —
Paper clamp board E
- Use the paper clamp board to hold
paper in position during alignment
when it is collapsed such that it is
difficult to use. —
SI
Paper tray
| Using the A3 (large-size paper) paper guide |
g g g
Attach the A3 paper guide when
handling A3 or 11”x17” paper.
Use four flat countersunk head
screws to attach the A3 paper guide.
boo
When using the paper tray while setting it horizontally, load sheets of paper little by
little (If the paper is loaded in mass, the tray receives the weight all at once, which
makes it difficult to jog the paper properly).
* Loosen the paper so as to let air in it.
HP
MES Ta Г
С, Du Hi 7
ch J Ca | 6 E
Ar
PEE
ка L
me N
- - = +
т eu +
= Го + a || я -
+ + a ea, E
Ze pr in Fer
far
fe ab Le SA
Г, Lo
TE
- -
2
mi
3 duree pre fi ci ne + Тс
(Rohs all a HE a
5. Troubleshooting
Problem ~ Probable cause Corrective action
1) Isn't the paper size greater in
Paper is excess of the designated Align the paper by raveling it.
poorly maximum paper size?
aligned. Try to produce clearances between
2) Isn't the paper statically charged? | the successive sheets of paper by
hand.
3) Isn't the paper stack too high? Narrow down each paper stack.
The BEE 1) Isn't the power switch set at the Set the vibration switch to the “Cont”
Р PE OFF position? or “Foot” position.
tray wont |
vibrate.
2) Hasn't the fuse blown out?
Replace the fuse.
@ If the new fuse blows again, there might be some fault inside the machine.
Contact the nearest dealer in your area.
6. More Tips
Be careful in relocating the machine to observe its overall balance during
transit so it will not fall down, instead of pushing or pulling the paper tray
or the upper part of the stand alone.
Do not apply undue force to the machine, as by pushing or pulling the
paper tray. Otherwise, the machine may have a trouble.
A power switch set at the OFF position and a foot switch in a released
state are functionally equivalent, but remember that pressing down the
foot switch will activate the machine.
Do not place a heavy item on the machine. The item may be unbalanced
and fall down, which may cause an injury.
7. Specifications
Product name Compact paper aligner, desktop
Model JT-7
Vibration method | By eccentric balanced weight
B6 to A3 sizes:
ares paper Max.: A3 [290mm x 420mm (About 11.5 inches x 16.5 inches)]
Min.: B6 [128mm x 187 mm (About 5.0 inches x 7.4 inches)]
430 (W) x 370 (D) x 350 (H) (mm)
Dimensions 17.0" (W) x 14.6" (D) x 13.8” (H) (inch)
(with the paper tray set in vertical position)
Mass (weight) 15 kg (33 Ib)
Power supply 110 to 120 VAC or 220 to 240 VAC, 50/60 Hz, 60W
As our continuing policy of product improvement, the product design and specifications are
subject to change without notice.
">
