Yamato | DN410H/610H | Operating instructions | Yamato DN410H/610H Operating instructions

DRYING OVEN
Model:
DN410H
Version 2
Yamato Scientific Co., LTD.
Congratulations on your selection of Yamato Scientific’s Drying Oven!
Please read these operating instructions, user notes and the warranty card thoroughly before the
initial operation of your drying oven. This will ensure proper operating procedures and extended
life for the unit. Please keep the operating instructions together with the warranty card for easy
access whenever you need them.
Attention: Read the warnings in the operating instructions carefully to familiarize
yourself with the initial operation of your drying oven.
Depending on the extent and nature of danger, the warnings given in these operating instructions
are classified into the following two categories by symbol.
To protect operators from accident -Negligence of this warning may result in a serious accident.
To protect the Drying Oven from damage -Negligence of this warning may result in damage to the Drying Oven. This
warning also gives you tips on performance that are useful in its operation and
maintenance or indicates the common mistakes that operators often make.
TABLE OF CONTENTS
EXPLANATION OF PICTURE DISPLAY ...................................................................................................1
SAFETY PRECAUTIONS .............................................................................................................................2
NOTES TO USERS........................................................................................................................................4
DESCRIPTION AND FUNCTION OF EACH PART...................................................................................4
Main unit.....................................................................................................................................................4
Control Panel ..............................................................................................................................................5
REQUIREMENTS FOR INSTALLATION...................................................................................................7
PRECAUTIONS IN HANDLING................................................................................................................10
OPERATING PROCEDURE .......................................................................................................................13
FIXED TEMPERATURE OPERATION INSTRUCTIONS.......................................................................14
AUTO START OPERATION INSTRUCTIONS .........................................................................................15
AUTO STOP OPERATION METHOD ..................................................................................................................16
PROGRAMMED OPERATION METHOD .............................................................................................................18
SWITCHING FROM ONE OPERATION TO ANOTHER .........................................................................19
METHOD OF USING DISPLAY KEY........................................................................................................20
HOW TO USE THE MODE.........................................................................................................................21
CONTENT OF FUNCTION MENU.......................................................................................................................21
CALIBRATION OFFSET FUNCTION ..................................................................................................................22
Outline of Function ..................................................................................................................................22
Setting The Calibration Offset Function ................................................................................................23
SAFETY DEVICES AND ERROR CODES ................................................................................................24
PURPOSES AND OPERATIONS OF SAFETY DEVICE AND COUNTER-MEASURES................................................24
INDEPENDENT OVERHEAT PREVENTION .........................................................................................25
BEHAVIOR AFTER POWER RESTORATION .........................................................................................26
MAINTENANCE AND INSPECTION .......................................................................................................27
MAINTENANCE PROCEDURE ..........................................................................................................................28
LONG STORAGE AND DISPOSAL......................................................................................................................28
AFTER SERVICE AND WARRANTY ........................................................................................................29
IF A SERVICE CALL IS REQUIRED: ..................................................................................................................29
TROUBLESHOOTING................................................................................................................................30
SPECIFICATIONS ......................................................................................................................................31
WIRING DIAGRAM ....................................................................................................................................32
REPLACEMENT PARTS TABLE...............................................................................................................33
REFERENCE ...............................................................................................................................................34
HAZARDOUS MATERIAL..........................................................................................................................34
LIST OF SYMBOLS IN THE DISPLAY .................................................................................................................35
FLOWCHART OF OPERATIONAL PROCEDURES ................................................................................................36
Run “MENU”.............................................................................................................................................36
Program “MODE” .....................................................................................................................................37
Flowchart for programming.....................................................................................................................38
Explanation of picture display
MEANING OF ILLUSTRATED SYMBOLS
Illustrated Symbols Various symbols are used in this safety manual in order to use
the unit without danger of injury and damage of the unit. A list
of problems caused by ignoring the warnings and improper
handling is divided as shown below.
Be sure that you understand the warnings and cautions in this
manual before operating the unit.
If the warning is ignored, there is the danger of a problem that
may cause a serious accident or even fatality.
If the caution is ignored, there is the danger of a problem that
may cause injury/damage to property or the unit itself.
Meaning of Symbols
This symbol indicates items that urge the warning (including the
caution).
A detailed warning message is shown adjacent to the symbol.
This symbol indicates items that are strictly prohibited.
A detailed message is shown adjacent to the symbol with
specific actions not to perform.
This symbol indicates items that should be always performed.
A detailed message with instructions is shown adjacent to the
symbol.
1
Safety Precautions
WARNING
Do not use the unit in an area where there is flammable or explosive gas.
Never use the unit in an area where there is flammable or explosive gas.
The unit is not explosion-proof. An arc may be generated when the power switch is turned on or
off, and fire/explosion may result.
Always ground the unit.
Always ground the unit on the power equipment side in order to avoid electrical shock due to a
power surge.
If a problem occurs, you should:
If smoke or strange odor should come out of the unit for some reason, turn off the power key
right away, then turn off the earth leakage breaker and the main power. Immediately contact
a service technician for inspection. If this procedure is not followed, fire or electrical shock may
result.
Never perform repair work yourself, since it is dangerous and not recommended.
Do not use the power cord if it is bundled or tangled.
Do not use the power cord if it is bundled or tangled.
overheat and fire may be caused.
If it is used in this manner, it can
Do not process, bend, wring, or stretch the power cord forcibly.
Do not process, bend, wring, or stretch the power cord forcibly.
result.
Fire or electrical shock may
Do not put the power cord under the desk, chair, etc.,
Do not put the power cord under the desk, chair, etc., or through an object.
shock may be caused.
Fire or electrical
Do not run the power cord next to heating equipment such as a heater.
Do not run the power cord next to heating equipment such as a heater.
may melt and fire or electrical shock may result.
2
The cover of the cord
WARNING
Substances that can not be used.
Never use explosive substances, flammable substances and substances that include explosive
or flammable ingredients in the unit. Explosion or fire may occur.
Do not disassemble or modify the unit.
Do not reconfigure the unit.
Fire or electrical shock may be caused.
Do not touch the door during or immediately after operation.
Do not touch the door during or immediately after operation.
caused due to the high temperature.
Severe burning injury may be
CAUTION
During a thunder storm . . .
During a thunderstorm, turn off the power key immediately, then turn off the earth leakage
breaker and the main power. If this procedure is not followed, fire or electrical shock may be
caused.
Periodic check of the safety component.
The independent temperature over-rise prevention device is important safety component. Be
sure to inspect it periodically. (See chapter of INDEPENDENT OVERHEAT PREVENTION on
page 25.)
3
Notes to Users
DESCRIPTION AND FUNCTION OF EACH PART
Main unit
Door handle
Power switch
(Earth leakage breaker)
Control panel
Exhaust port
Power cable
4
Control Panel
⑪
⑪f
⑪
⑪e
⑪b
⑪c
⑪
⑯
⑭
⑫
⑨
②
①
④
③
⑮
⑤
⑧
(1) POWER key:
(2) MODE key:
(3) DISPLAY key:
(4) MENU key:
(5) ENTER key:
(6)/(7)
(UP/DOWN) key:
(8) ESCAPE
key:
(9) Main Display:
(10)Sub Display:
(11)Operation monitor:
a) (11) STANDBY lamp:
b) (11) Temperature
pattern lamp:
c) (11) OVER lamp:
d) (11) TROUBLE
indicator lamp:
⑥⑦
⑩
⑬
Key to change over the controller from the standby mode to the
operation mode or from the operation mode to the standby mode.
Key to select a function from program input, edit, delete modes,
hour/time setting, change-over mode, and other functions.
Key to change-over the display content of the sub display (10).
Display content is changed over to set temperature, remaining
time, hour, execution segment No.
Key to select the operation mode. Each mode of fixed
temperature, auto-start, auto-stop and program operation can be
selected.
Key to determine the input value of set value (temperature, time,
hour, etc.), selection mode, execution segment No. etc.
Key to change set value (temperature, time, hour, etc.) and to
choose a selection from various parameters on the function menu.
Key to cancel the latest entry and recover the status that was valid
prior to the making the latest selection.
It displays temperature measurements, set values (temperature,
time, hour, etc.), program information, error information, etc.
It displays set temperature, remaining time, current hour and
execution segment No. etc.
It indicates an operation mode.
It flashes to indicate that the instrument is in the preoperational
standby mode.
It illuminates to indicate the heat treatment process pattern
executed by the controller with flashing light indicating the point
currently in execution.
It flashes to indicate the end of auto-stop or program operation.
It blinks when an error is detected and displays the corresponding
code for that particular problem.
5
e) (11)REMOTE operation
indicator lamp:
f) (11)KEY LOCK
indicator lamp:
(12)Operation menu
indicator lamp:
(13)Sub display menu
indicator lamp:
(14)HEAT ON indicator
lamp
(15)TIME indicator lamp:
(16)Independent
Temperature
Overheating Prevention
Device:
It illuminates when the instrument is put into remote operation
(optional) and displays the word “REMOTE.”
It illuminates to indicate that the operation panel key lock function is
in operation.
It illuminates to indicate the active operation mode in the operation
menu.
It illuminates to indicate the item (set temperature, remaining time,
hour or execution segment) shown in the sub display.
It illuminates when the heater is on.
It illuminates when the operation starting time of the auto-start and
the operation completion time of the auto-stop is set in the hour
setting mode.
Setting the instrument to the operational temperature of the
independent over rising prevention.
6
REQUIREMENTS FOR INSTALLATION
Do not use the unit in an area where there is flammable or explosive gas.
Never use the unit in an area where there is flammable or explosive gas. The unit is
not explosion-proof. An arc may be generated when the power switch is turned ON
or OFF, and fire/explosion may result.
Explosive gas
Flammable gas
Always ground the unit.
z Connect the grounding cable to your ground conductor or ground terminal.
z Do not forget to ground the Oven, to protect you and the unit from electrical shock
in case of power surge.
z Do not connect the grounding wire to a gas pipe, or by means of a lightning rod or
telephone line. A fire or electrical shock will occur.
NOTE: The oven is for the 220V use. It has not a power plug.
Choose a correct power distribution board.
z Choose a correct power distribution switchboard or receptacle that meets the
oven’s rated electric capacity.
Electric capacity
AC 200 V, single phase 16A
z Do not connect the oven to an outlet that differs from the above specifications
because a fire or electrical shock will occur.
Supply connections for the oven
z Request the supply connection for the 200V specifications from a licensed
electrician.
z Failure to have this operation complete by certified personnel will cause a fire or
electrical shock during Oven operation.
Install the Oven on a level area.
z Do not installation the oven on a non level surface. This will cause hazards to the
operator and create problems during actual operation.
7
Choose a proper place for installation.
z Do not install the oven in a place where:
♦
♦
♦
♦
♦
♦
Flammable gas or corrosive gas is generated.
Ambient temperature exceeds 35°C.
Ambient temperature fluctuates violently.
There is direct sunlight.
There is excessive humidity and dust.
There are constant vibrations.
z Keep the following clearance around the oven.
Or more
Or more
Or more
After installed, you should:
z It may cause injure to a person if this oven falls down or moves by the
earthquake and the impact, etc..
z To prevent, take measures that the unit cannot fall down.
z Secure the unit by putting the stoppers on the casters.
8
Handling of power code.
z Do not use the power cord if it is bundled or tangled.
can overheat and fire may be caused.
If it is used in this manner, it
z Do not process, bend, wring, or stretch the power cord forcibly.
shock may result.
Fire or electrical
z Do not put the power cord under the desk, chair, etc., or through an object.
or electrical shock may be caused.
z Do not run the power cord next to heating equipment such as a heater.
cover of the cord may melt and fire or electrical shock may result.
Fire
The
z When the power cord is damaged (exposure of the core wires, disconnection,
etc.), turn off the power key right immediately, then turn off the earth leakage
breaker and the main power. Contact customer service for a replacement
immediately. If this procedure is not followed, fire or electrical shock may be
caused.
Caution in setting shelves
z Do not use any shelves but the attached ones.
If it is used in this manner, the oven cannot occasionally regulate temperatures
properly.
z Put the attached shelves on the shelf brackets fitted to the chamber when you use
the oven.
9
Precautions in handling
Substances that can be used
z Never use explosive substances (shown on page 34), flammable substances
(shown on page 34) and substances that include explosive or flammable
ingredients in the unit. Explosion or fire may occur.
Do not put the foreign substances in the oven.
Do not put a foreign substances such as metals or flammable substances in the
opening of the unit (ventilation hole and exhaust port, etc.). If this procedure is not
followed, fire, electrical shock or burn may result.
If the foreign substances enter the unit, turn off the earth leakage breaker
immediately and contact a service technician for inspection. If this procedure is not
followed, fire, electrical shock or burn may result.
Caution in taking out samples
During and immediately after operation, the internal surfaces of the chamber and the
door are extremely “HOT." To prevent injury, take out the samples when the
chamber has cooled down or wear gloves while the chamber is still hot.
When you open the door during working at the high temperature.
Do not touch the internal surfaces of the chamber and the door when you will open
the door, because they are extremely hot.
To open the door while the chamber is still hot may cause the malfunction of a fire
detector if it is installed near the oven.
Do not touch heated parts.
Do not touch the door during or immediately after operation. Severe burning injury
may be caused due to the high temperature.
Do not climb on the oven
Do not climb on top of the oven because it will fall down and break.
Failure to observe this caution may cause injury to a person.
Do not put anything on the oven
Do not put anything on top of the oven because they will fall and result in injury to a
person.
10
Caution about the temperature range.
Use the oven in the range of 40°C to 210°C.
When you use the oven for the first time
During the initial operation, the oven may occasionally generate an odor especially
when high temperatures are reached. This odor is normal and does not signal a
problem with the oven. The adhesive on the insulation melting causes the nature of
the odor.
About the temperature in the chamber
Temperature display indicates the sensor temperature installed in the unit, however it
does not always correspond to the temperature of the sample when the sample
volume is very large or when the temperature is on the increase.
Caution about a drenched sample
z When using a very wet sample, try to drain it as much as possible before putting it
in chamber.
Caution about a powdery sample and the loading of samples
There are times when a powder sample is scattered by the sudden decompression
operation or purge operation. When performing decompression or purge, open the
valve very slowly.
It occasionally takes a long time before the chamber reaches the target temperature if
the camber is congested with samples or a sample with the large specific heat is in it.
In such cases, reduce samples. Moreover, note that the temperature display
occasionally unsettle when you process an exothermic sample.
Distribute samples
z
z
Each shelf can carry a uniform load of 15 kg (33 lb.). When you place samples
on a shelf, distribute them evenly over the shelf area.
If a shelf is congested with samples, the oven occasionally cannot regulate
temperatures properly. To ensure the oven’s temperature accuracy, there should
be open space of at least 30% on each shelf.
Never use corrosive samples
Most parts are made of stainless steel (SUS304). However, strong acid occasionally
corrodes even stainless steel. Besides this, the silicone rubber packing is also
vulnerable to acid, alkali, oil and halogens' solvents
11
Do not place any samples on the bottom of the chamber
z Do not place any samples on the bottom of the chamber to heat,
because it affects the temperature control of the oven.
Sample
z Always put the samples on the attached shelves. Place sample so that
it does not touch the interior wall of the chamber.
z Set the shelves on the shelf brackets that will accommodate the size of
the sample.
During a thunder storm
During a thunderstorm, turn off the power key immediately, then turn off the
earth leakage breaker and main power. If this procedure is not followed,
fire or electrical shock may be caused.
In case of power failure
Once the power supply has been cut off due to power failure, and then the
power supply is restored, the oven will resume running.
When you open and shut the door
Do not put your hand either face near the door when you open and shut
the door. Failure to observe this caution may result in injury because the
door hits your hand or face.
12
Operating Procedure
When prepared completely, proceed as follows:
1. Turning on of power supply
2. Selection of operation menu
• Press the MENU key several times to select
• Turn on the earth leakage breaker.
desired operating method.
• It allows you to enter each parameter into a
• The present time is shown on the sub display.
flashing menu.
• Push the POWER key in the operation panel.
• When once the power is on, this oven becomes
a standby state. Under such a condition, every
operation mode can be selected by pushing the
MENU key.
3. Explanation of operation menu
Fixed
Temperature
: It is an operation method to bring the oven to the desired temperature and
keep it steady.
Auto stop
: It is an operation method to stop a fixed temperature operation when
reached the set time or hours.
Auto start
: It is an operation method to start the fixed temperature operation when
reached the set time or hours.
Program
: It is an operation method that can start or stop an operation either when
reached the set time or hours. Moreover, it can change the temperature
when reached the desired time and repeat to do that.
13
FIXED TEMPERATURE OPERATION INSTRUCTIONS
Selection of operation
menu
Input of set temperature
• Push the ENTER key after
• Push the MENU key and
select the fixed temperature
operation.
making a sub-display display
an arbitrary set temperature
pushing ▲▼ keys.
Changing the set
temperature when fixed
temp operation is in
progress
• Push
either the ▲ key or
the ▼ key to display the
desired temperature on the
main display and push the
ENTER key.
Push the MENU key.
Press either the ▲key or the ▼ key
several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired set temperature will
appear on the main display.
The lamp of the FIXED TEMP blinks.
• The temperature set last time
is blinking and enters the state
that a set temperature can be
input in a sub-display.
Press the ENTER key.
• The oven will start to run the
fixed temperature operation
to the renewed temperature.
Push the ENTER key.
• The oven will start to run the
fixed temperature operation
to the renewed temperature.
14
AUTO START OPERATION INSTRUCTIONS
Selection of operation menu
Inputting the set temperature
• Select AUTO START mode by
• Press either the ▲ key or
pushing the MENU key.
the ▼ key to display the
desired temperature on the
main display and push the
ENTER key.
Inputting the desired set
time
• Press either the ▲ key or
the ▼ key to blink start time
(or the hour) on the main
display, and press the
ENTER key.
Push the MENU key.
The operation menu lamp of an AUTO
START blinks.
•
Press either the ▲ key or the ▼ key
several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired start time (or hour)
will appear on the main display.
will appear on the
sub display and the desired
temperature can be input.
Sub display
Press The ENTER key.
Press the ENTER key.
•
will appear on the
sub display and the operation
start time can be input.
• The STANDBY lamp of the
operation monitor blinks.
• The operation will be in standby
condition.
• After reaching the set time
(or hour), the oven will start
to run the auto start
operation to the renewed
temperature.
15
Auto Stop Operation Method
Selection of operation menu
Inputting the set temperature
• Press the MENU key and
• Push either the ▲ key or
select the auto stop operation.
the ▼ key to blink the
desired temperature on the
main display and push the
ENTER key.
Inputting the desired set
time
• Push either the ▲ key or
the ▼ key to blink your
desired time (or hours) for
operation stop on the main
display, and press the
ENTER key.
Press the MENU key.
The menu lamp of an AUTO STOP
blinks.
•
Press either the ▲ key or the ▼
key several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired stop time (or hour)
will appear on the main display.
will appear on the
sub display and the desired
temperature can be input.
Sub display
Push the ENTER key.
The main display will light up to
indicate the set temperature you have
chosen.
Push the ENTER key.
After about 1 second
•
will appear on the
sub display and the operation
stop time can be input.
16
•
will appear on the
sub display and you can
chose the wait function to be
activated or not.
Selection of wait function
• Press either the ▲ key or the
▼ key to indicate the wait
function (ON or OFF) on the
main display. Then press
ENTER key.
Working conditions of timer
• Auto Stop timer activates when:
1. The wait function is on.
It starts when the set temperature has
reached the target value.
2. The waiting function is off or the time
setting represents hours.
Press either the ▲ key or the ▼ key
several times.
Either ON or OFF will appear on the
main display.
(activate)
It starts right after the auto stop
operation is started.
(inactive)
Press the ENTER key.
• This operation activates the
auto stop operation.
17
Programmed Operation Method
Selection of operation
menu
Input of execution
program number
Input of time
• Press either the ▲ key or
• Press the MENU key and
select
the
operation.
• Press either the ▲ key or
programmed
the ▼ key to indicate an
desired program number on
the main display, and press
the ENTER key.
the ▼ key to blink your
desired operation start time
(or hour) on the main display,
and press the ENTER key.
Press the MENU key.
The operation menu lamp of the
PROGRAM blinks.
•
Press either the ▲ key or the ▼ key
several times.
The program number will appear on
the main display.
NOTE: If no programs have been set,
―――― is blinking.
See the Operating Instructions
for Programmable Controller
to set a new program.
will appear on the
sub display and the execution
program number can be input.
Press either the ▲ key or the ▼ key
several times.
The desired set time will appear on
the main display.
Push the ENTER key.
Push the ENTER key.
• The standby lamp on the
•
will appear on the
sub display and the operation
start time can be input.
18
operation monitor blinks.
(Operation is in STANDBY
MODE)
• The operation will start after
the set time is up.
SWITCHING FROM ONE OPERATION TO ANOTHER
This instrument can switch to a different operation mode without stopping the current program no
matter what mode it is in, fixed temperature operation, auto-start/stop operation, and program
operation.
Selection of operation menu
• Press the MENU key several times until the
desired operation menu lamp flashes on the
Operation Menu.
• Since the current operation has not stopped, the
operation menu lamp is also lit.
• On the Operation monitor -- the temperature
pattern indicator lamp blinks with the current
segment being executed.
Press MENU key several times.
• This status allows you to enter each parameter
into blinking or lighting operation menu.
When the fixed temperature operation is selected
ƒ The main display shows the current internal
temperature.
ƒ The sub-display flashes the temperature set by the
previous fixed temperature operation.
When auto-start operation is selected
ƒ The main display flashes the temperature set by the
previous auto-start operation.
ƒ
The sub-display shows
(Temp.)
When auto-stop operation is selected
ƒ The main display flashes the temperature set by the
previous auto-stop operation.
ƒ
The sub-display shows
(Temp.)
When program operation is selected
ƒ The main display flashes the previously set program
number.
ƒ
The sub-display shows
(Program)
The lamp blinks or lights.
• Now operate according to the operation method you have chosen, see that section of this instruction
manual.
19
Method of using DISPLAY key
The display content of the sub display can be changed over by turns when pushed the DISPLAY
key.
Operation mode
Sub display
Fixed temperature
operation
Set temperature
Hour
Remaining time
Standby
Hour
Auto start
operation
Set temperature
During operation
Remaining time (*1)
Hour
Set temperature
During operation
Auto stop
operation
Remaining time (*2)
Hour
After time is up
Hour
Remaining time
Standby
Hour
Set temperature
Remaining time
Program operation
During operation
Hour
Execution segment (*3)
Hour
After finished
*1: HOLD is displayed.
*2: When the wait function is set to on,
is displayed in the waiting status.
*3: The DISPLAY key will enable to show the rest of the repeat count while the repeat operation.
20
How to use the MODE
Content of function menu
This controller has the other functions shown bellow.
• Press the MODE key and display your desired
function on the main display by pushing either the
key or the
key. Each function will appear by
turns whenever pushing the
keys.
Press the mode key.
Select with the ▲ key or
the ▼ key.
Main display
Function
Inputting and editing
programs
To input and edit the program.
To delete existing programs that are no longer necessary.
Confirmation of the program contents should be performed
prior to deleting and in accordance with Programmed
Operation Method.
To input either an hour or a period of time during time
setting process in the various operation modes -Switching time
auto-start/stop, and program operation.
setting mode.
It is set to the time (a period of time) setting mode when the
product was shipped from the factory.
To set or release the key lock function.
This function is for protecting wrong key actions during the
operation or while being in the standby state.
Setting and releasing
Once set to ON, the key lock will disable you from doing
the key lock.
the POWER, MENU, ENTER, and DELETE key action.
If the key lock function is set, the KEY LOCK lamp on the
operation monitor is lit.
To select whether you want to activate the alarm buzzer or
Alarm buzzer
not when an error occurs.
ON/OFF function.
Deleting the
Program.
Accumulating time
display function
Hold function
Date and current
hour setting function.
Calibration offset
function
To display the total duration that the POWER key is on,
within the range of 0 to 49999 hours.
To hold the operation that is currently running. This function
will get active only when you run the oven in auto-start/stop
or program operation mode (includes the standby state).
In addition, it will work when the setting of the operation
start time for auto-start and program operation as well as
the operation end time for auto-stop are set in the form of
“Time” and not in the form of “Hour.”
To set the date and hour.
To conform the display temperature to the measurement
temperature of a voluntary point in the chamber at a
voluntary temperature. Details are described on page 22
21
Calibration Offset Function
Outline of Function
In the controller, the relationship between the temperature
T detected by the sensor and the display temperature of
the operation panel D is expressed by the equation of the
line which passes the two points (T0, D0) and (TS, DS)
DS
shown in Fig. 1.
Here, T0 is the sensor detecting temperature when the chamber
y=ax+b
central temperature becomes the zero adjusting temperature
D0
(normally room temperature is adopted) D0 at the time of no load, TS
is the sensor detecting temperature when the chamber central
temperature becomes the span adjustment temperature (normally
T0
TS
working maximum temperature is adopted) DS at the time of no load
Sensor detection temperature
in the same way.
As it is clear from the facts above, conforming of the chamber central
Fig. 1
temperature and the display temperature is guaranteed only when
there is no load and at two points shown above. In other words, it is
possible for a temperature measured at a point in the chamber does not conform to the display temperature
of the operation panel at a voluntary temperature without load.
This is the function to move the line which passes above two points to the Y axis direction in parallel
(increase or decrease y intercept of the line). The parallel movement amount including a sign is defined as
the calibration offset. This function can conform the display temperature of the operation panel to the
measurement temperature of a voluntary point in the chamber at a voluntary temperature.
Display temperature
(Controlled temperature)
In Fig. 2, DSV is a display temperature of the
operation panel under the condition that the
temperature in the chamber is constant for a set
temperature. It is natural to say that this value is
equal to the target set temperature. DPV is a
measurement temperature of a voluntary point in the
chamber under this condition.
The difference
between DPV and DSV including the sign is defined
as the calibration offset. Therefore offset is shown
as below.
△DCAL＝DPV－DSV
Equation 1
Display temperature
(Controlled temperature)
Parallel movement
DSV
△DCAL
DPV
Ti
TV
Sensor detection temperature
In Fig. 2, ΔDCAL becomes the negative value since the target
set temperature DSV is larger than the actually measured
In order to conform the display
temperature DPV.
temperature to the actually measured temperature, let the controller to recognize that the temperature in the
chamber differs from the target set temperature by ΔDCAL.
Fig. 2
NOTE: Setting Tolerance of Calibration Offset
♦
♦
The calibration offset can be set within ±5% of the maximum working temperature of the oven.
(Therefore, the setting tolerance of the calibration offset is ±19°C.)
Initial off set value has been set to 0°C when shipping.
22
Setting The Calibration Offset Function
This function can be activated when the controller is in the condition of accepting the MODE key.
EX. Bring the oven to the target set temperature 100°C and allow it to reach the steady state. After
then, measure the temperature at a point in the chamber. If it shows 97°C when the main display
shows 100°C, you can conform your measuring value to the one on the display by using the
calibration offset function.
Calibration offset ΔDCAL is obtained from the
Equation 1 (page22) as shown below.
△DCAL＝97℃－100℃＝－3℃
Procedures to set the calibration offset ΔDCAL to the controller are shown as below.
Setting and changing the calibration offset value
• Push the MODE key, and then push the
main display.
key or the

key several times to display
Push the
key or the
on the
key several times
• The sub display shows the calibration offset value that has been set the last time.
NOTE: When the unit is shipped from the factory, the sub-display shows 0 as the
calibration offset value.
Push the ENTER key.
• The main display flashes the preset calibration offset value.
⇒ In this state, the set value of the calibration offset can be changed.
• The sub display shows
.
Push the key or the key several times
• Push either the
key or the key to change the value on the main display to your desired value
(calibration offset value to be set newly).
When the changing is completed, push the
ENTER key.
• The changed value is entered and both the main and the sub displays return to the display mode just
before pushing MODE key. The controller starts the temperature controlling operation in order to
make the difference zero, since the difference is generated between the target set temperature and
the temperature in the chamber by the changing of the calibration offset value.
23
Safety Devices and Error Codes
Purposes and Operations of Safety Device and Counter-measures
This instrument incorporates an automatic diagnosis function built in the controller and safety
devices independent of the controller. The purposes and operations of the safety devices and
countermeasures are shown in the Table below. When an abnormal condition occurs, an error
code is displayed in the main display. Immediate action should be taken according to the specific
counter-measures.
Safety Device
1. Earth leakage breaker
Display
No Display
2. Sensor malfunction
detector
3. Triac circuit detector
4. Disconnected heater circuit
detector
5. Independent overheating
prevention
TROUBLE lamp flashes.
flashes.
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
flashes.
6. Main relay malfunction
detector
7. POST function*
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
,
,
Cause & Counter-measures
• Power circuit interrupted
• Erases all displays
⇒ Report to our service office and
check the cause of the problem.
• Break in temperature sensor circuit.
⇒ Report to our service office.
• Short circuit in triac.
⇒ Report to our service office.
• Heater circuit is disconnected.
⇒ Report to our service office.
• Incorrect setting of the independent
overheating prevention.
⇒ Set correctly.
• Heating of sample
⇒ Reduce the amount of the sample.
• Malfunction of the independent
overheating prevention circuit.
⇒ Report to our service office.
• A malfunction of the main relay.
⇒ Report to our service office.
• Contact Yamato Sciectific’s
Technical Service Department.
flashes.
8. Automatic overheating
preventive function
9. Key lock
10. Memory backup circuit
11. Door switch
z
No Display
Key lock display lamp lights up
No Display
flashes
• Heating of samples
⇒ Reduce amount of samples
•
This function prevents the disruption
of operation due to incorrect
operation. Leave it on during
operation. (See section in this
manual for setting and resetting
methods on page 21).
• It is not the fault.
⇒ When opened the door,
will
flash on the sub display and the
heater circuit will be cut off and the
fan will stop for safety. Once closed
will go out and
the door,
the heater circuit and the fan will
resume working.
POST (Power On Self Test) function checks the microprocessor, memory surrounding LSI, surrounding
circuit of the controller every time “POWER” key is turned ON. This is the function for checking that the
controller won’t have a fatal fault before starting the operation.
24
INDEPENDENT OVERHEAT PREVENTION
There are two safety devices in this unit: the auto-overheating preventive function of the
controller (automatic recovery) and the independent overheating prevention (manual recovery).
Circuits and sensors that are independent from the controller configure them. These safety
devices for the temperature overheating prevention protect the instrument in a fail-safe method.
Setting the Temperature Range and Function
Setting
Temperature:
Input Method:
Function:
0 to 399oC
Three integer digital switch. Turn the drum of each column and set the desired
value. The first integer can only be from 0 to 3 for the hundred columns.
Heater output is cut off when the measured temperature gets higher than the set
temperature of the independent overheating prevention. The function is active
when the earth leakage breaker is ON.
When the independent overheating prevention is activated, is flashing on the
main display with the TROUBLE lamp flashes. When the independent overheat
prevention is active while the heater is in the temperature rising process, etc.,
and flash alternately on the display.
Activation/Setting Method
1. Set the independent overheating prevention 15oC higher than the set temperature of the main
unit.
2. When setting the proper value to protect the sample, be sure it is well above room temperature,
and set it at least 15oC higher than the maximum temperature set value of the temperature
pattern of the program.
3. When the independent overheating prevention is activated improperly by changing the setting
of the independent overheating prevention lower than the internal temperature or by continuing
operation when the setting on the unit is too low, turn off the earth leakage breaker to reset the
unit and perform the setting again.
If it is activated by another reason, see chapter of Safety
Devices and Error Codes on page 24.
Precautions
1. Only 0 to 3 can be set for the column of hundreds of the digital switch by the stop mechanism;
however, if forced to change it to a value higher than 3, it will damage the unit.
2. Set temperature can change by touching the setter when cleaning.
set temperature is correct after cleaning or before operation.
25
Always confirm that the
Behavior after Power Restoration
In case of power failure during operation, the controller resumes the following operations after the power
restoration.
In case of power failure during the program operation
The controller automatically resumes the program operation where it left at the power shutdown. In case
that the temperature inside the chamber is outside the specified temperature range based on the setpoint
temperature, the controller goes to the FORECED WAIT STATE until the temperature inside the chamber
comes back to the specified temperature range. When you select the display of the remaining time by
pushing the Display key in this condition, the sub display shows
.
The timer built-in the controller does not count as running time for a period of power failure.
In case of power failure during the Auto-Stop operation
The controller automatically resumes the Auto-Stop operation where it left at the power shutdown. In
case that the temperature inside the chamber is outside the specified temperature range based on the
setpoint temperature after the power restoration, the controller goes to the FORECED WAIT STATE until
the temperature inside the chamber comes back to the specified temperature range. When you select the
display of the remaining time by pushing the Display key in this condition, the sub display shows
. (Forced Wait)
In case that the operation stop time is set in a period of time, the timer built in the controller does not
count as running time for a period of power failure.
On the contrary, in case that the operation stop time
is set in hours, the timer built in the controller counts as running time for a period of power failure.
When the operation stop time reaches during power failure, the controller stops running just after the
power restoration.
In case of power failure while the controller is in standby condition
In case that the operation start time is set in a period of time, the timer built in the controller does not
count as standby time for a period of power failure.
On the contrary, in case that the operation start
time is set in hours, the timer built in the controller counts as standby time for a period of power failure.
When the operation start time reaches during power failure, the controller starts running just after the
power restoration.
In case of power failure during the fixed temperature operation and a soak period of
the Auto-Start operation
The controller resumes running toward to the preset temperature after the power restoration.
26
Maintenance and Inspection
Do not disassemble and modify the oven.
z
Do not disassemble the oven. There are parts in the unit with high voltage;
therefore, if the unit is disassembled, electric shock and injury may result.
Ask the Yamato Scientific office for inspection, adjustment, and repair of the inside of
the unit.
z Unauthorized modification will be hazardous and cause problems in the operation
of the Oven.
Modification
Maintenance Precautions
z Before starting inspection or maintenance, disconnect the power plug from the
receptacle.
z Conduct inspection and maintenance only after the oven has cooled down.
z When you remove dirt or stains from the unit’s resin parts and the control panel,
use a soft wet cloth. Do not use benzene, thinner, cleanser or a hard brush; it will
cause deformation, qualitative deterioration and/or discoloring of the components.
Periodic inspection of the safety component.
z The independent temperature over-rise prevention device is important safety
component. Be sure to inspect it periodically.(See chapter of Maintenance
Procedure on page 28)
If you have any questions, contact our sales representative in your vicinity or our service office.
27
Maintenance Procedure
Operation Check of Independent Temperature Overheating Prevention Device
z After executing the fixed temperature operation at the set temperature 0°C, set the operation
temperature of the Independent Temperature Overheating Prevention Device to 0°C.
z Under normal circumstances, the heater circuit is cut off in a few seconds and the TROUBLE
lamp and
flashes at the same time, and the alarm buzzer sounds if the alarm
buzzer function is ON.
z After confirming, turn off the earth leakage breaker once, and then return the setting of the
Independent Temperature Overheating Prevention Device to the proper value. Turn the earth
leakage breaker back ON.
Always perform inspection before a long continuous operation or an unattended
operation.
Long Storage and Disposal
When you do not use the oven for a long period of time.
Disconnect the power cable from the power switchboard.
When you dispose of the oven.
Do not leave it where children can access.
to disable the door locking system.
28
Remove the knob and hinges of the door
After service and WARRANTY
If a Service Call is required:
If a Service Call is required
Warranty Card (attached to your Oven)
zIf a problem occurs with the Drying
Oven, record the error code on the
display and stop the operation
immediately, turn off the power switch,
and disconnect the power plug from the
receptacle. Contact our sales or
service representative.
zPlease fill out completely and return the
bottom portion of the warranty card
when the unit is received. The
completed top portion is your
Registration Card that should be
retained for your records.
zCheck the warranty card or the name
plate of your Drying Oven and give us
the information below.
•
Model of your oven;
•
Serial product number of your
oven;
•
Date of purchase; and
•
Problem with your oven (as
detailed as possible).
zWarranty period is one (1) year after
the date of your purchase. During this
warranty period, we will offer free repair
service on the basis of the conditions
provided on the warranty card.
zIf you need repair service after
expiration of the warranty period,
contact our sales or service
representative in your vicinity or service
office for advice.
Minimum Inventory Period of Repair Parts
Repair parts will be available for at least 5 years after termination of our production of
Drying Oven Series. Repair parts mean the parts that are necessary to maintain the
performance of the ovens.
29
TROUBLESHOOTING
Problem
No display of current hour in the
sub-display at the activation of the earth
leakage breaker.
Temperature fluctuates during the
operation
•
•
•
•
•
It takes too much time for temperature to
rise.
•
Cause/Solution
Check if the power cable is firmly
connected to a receptacle.
Check for power failure.
Does ambient temperature fluctuate
violently?
Are there too many samples in the
chamber?
Are the samples too moist?
Are there too many samples in the
chamber?
30
SPECIFICATIONS
Model
Method
Performance:
Operating temperature
Temperature stability*1
Temperature Uniformity
Time to reach max. temp.*1
Structure:
Exterior
Interior chamber
Insulating material
Heater nominal capacity
Fan
Cable port
Exhaust Port
Controller:
Temperature control method
Temperature setting method
Temperature indicating method
Other indication
Timer
Operation function
Additional function
Heater circuit control
Sensor
Safety device
DN410H
Forced Ventilation
４０ ～ ３６０℃
±０．２℃（＠３６０℃）
±３．０℃（＠３６０℃）
Approx. 60 min.
Cold rolled steel plate with baked-on melamine resin finish
Stainless steel (SUS304)
Glass wool and Ceramic fiber
3.0kW
Sirocco fan, Output:10W×2
Inner diameter 30 mm (right side)
Inner diameter 30 mm x 2 (rear face)
PID control by microprocessor
Digital setting method by
keys (resolution: 1°C)
Digital display by green LED (resolution: 1°C)
Temperature pattern LED indication that shows operation indication
1 min. to 99 hrs. 59 min. or 100 hrs to 999 hrs
(Timer resolution: 1 min. or 1 hr.)
Fixed temperature operation
Auto-start/Auto-stop operation
Program operation (16 segments, repeat, etc.)
Calendar timer function (actual hr. timer within 24 hrs.)
Integrating time function (Integrated hr. up to 49999 hrs. can be
measured.)
Time indication (The present time is indicated.)
Calibration offset function
Triac zero cross system
K thermocouple (double sensor)
Earth leakage breaker with the over current protector
Self-diagnostic function (sensor abnormality, heater disconnection and
Triac short circuit detection; automatic temperature over-rise prevention)
Key lock function
Independent Temperature Overheat Prevention device
(Digital switch input system, setting temperature range: 0 to 399°C)
470 mm × 450 mm × 450 mm
640mm × 695mm × 930mm
95 l
Approx. 80 kg
AC 200 V, 50/60Hz, 16A single phase
Internal dimensions (WxDxH)*2
External dimensions (WxDxH)*2
Capacity
Weight
Power Requirements
Accessories:
2 sets
Shelf / Shelf brackets
For exclusive use of this oven and the controller: each one
Instruction manual
NOTES: *1. The values written on the chart have been measured with no sample and both exhaust ports
closed in ambient temperature of 20°C.
*2. Both of internal and external dimensions do not include the one of protruding parts.
31
WIRING DIAGRAM
ELB
P1
PIO
1
1
AC200V
2
J1
1
J2
3
X1
TF
2
7
4
FM
T1
SSR1 J1
T2
1
1
3
3
1
1
3
3
1
X1
5
3
40
40
TC
J7
J10
J23
＋
－
+ -
1
3
J29
PLANAR
DSW
P1
PIO
Part Name
Current Transformer
Door switch
Digital switch
Earth leakage breaker
Fan motor
Heater
Independent overheat
prevention
Terminal block
PIO board
Symbol
PLANAR
POWER1
SW
PI
SSR1,3
T
TF
Part Name
PLANAR board
Power board
Membrane keypad
Photo-interrupter
Solid-state relay
Transformer
Transformer
TH
X1
Thermocouple
Relay
32
SW
10
＋
TH
－
1
2
3
4
PI
DS
POWER1
1 2
J5
J2 J3
3
1
J1
J5 4
2
J4
OH 1 2
Symbol
CT
DS
DSW
ELB
FM
H
OH
J20
J15
J25
TH
30
1
J34
3
T1 SSR3
J1
T2
30
J19
J3
1
3 J4
CT
H
J19
1
1
J20
1
1
1
1
3
REPLACEMENT PARTS TABLE
Symbol
CT
ELB
FM
H
P
P1
PIO
PLANAR
POWER1
OH
PI
SSR
T
TF
TH
X1
Part Name
Current Transformer
Earth leakage breaker
Fan motor
Heater
Power code
Terminal block
PIO board
PLANAR board
Power board
Independent overheat
prevention
Photo-interrupter
Solid-state relay
Membrane keypad
Transformer
Transformer
Thermocouple
Relay
Code No.
2-17-001-0002
Specifications
CTL-6-S-400
2-06-005-0012
BJS30-3
2-14-001-0008
REK42A-4, AC200V
DN63H-30320
AC200V 1500W
2-13-001-0010
2-07-023-0002
1-24-000-0024
1-24-000-0059
1-24-000-0025
1-27-001-0008
T3 - 3d
M011-0FX 4P
IVCR
1-21-001-0002
LT00028423
1-01-320-0008
2-18-002-0003
2-18-000-0023
1-16-001-0042
2-05-000-0010
TLP802
SSR-01
Type 4H
AD21-100A
AC200V
K thermocouple (double sensor)
HE1a-DC12V
33
Type 1
IVLE
Reference
HAZARDOUS MATERIAL
Explosives
Explosives
Substances
Combustible
Substances
Oxidants
Flammable
s
Ignitable
Substances
Combustible
Gases
1. Nitroglycol, Nitroglycerin, Nitrocellulose, and other explosive
nitric esters.
2. Trinitrobenzens, Trinitrotoluene, Picric acid, and other
explosive nitro compounds.
3. Peracetic acid, Methyl ethyl ketone peroxide, Benzoyl
peroxide, and other organic peroxides.
Metallic lithium, Metallic potassium, Metallic sodium, Yellow
phosphorus, Phosphorus sulfide, Red phosphorus, Celluloid,
Calcium carbide, Lime phosphate, Magnesium powder,
Aluminum powder, and other ignitable metal powders and sodium
dithionite (hydrosulfite).
1. Potassium chlorate, Sodium chlorate, Ammonium chlorate,
and other chlorates.
2. Potassium perchlorate, Sodium perchlorate, Ammonia
perchlorate, and other perchlorates.
3. Potassium peroxide, Sodium peroxide, Barium peroxide, and
other inorganic peroxides.
4. Potassium nitrate, Sodium nitrate, Ammonia nitrate, and other
nitrates.
5. Sodium chlorite and other chlorites.
6. Calcium hypochlorite and other hypochlorites.
Ethyl ether, Gasoline, Acetaldehyde, Propylene chloride,
Carbon disulfide, and flammable substances with a flash point
below minus 30ºC.
Normal hexane, Ethylene oxide, Acetone, Benzene, Methyl
ethyl ketone, and flammable substances with a flash point
between minus 30ºC and 0oC.
• Methanol, Ethanol, Xylene, Pentyl acetate (amyl acetate), and
inflammable substance with a flash point between 0ºC and
30ºC.
• Kerosene, Light oil, Turpentine oil, Isoamyl alcohol, Acetic acid,
and flammable substances with a flash point between 30ºC
and 65ºC
Hydrogen, Acetylene, Ethylene, Methane, Ethane, Propane,
Butane, and other gases that are flammable under 1 atmospheric
pressure at 15ºC.
(Quoted from “Addendum Table1 of Code of Work Safety and Hygiene Standard”)
34
List of Symbols in the display
The oven has the controller with the 4-digit LED display. The meaning of symbols in the display is as follows:
Capital
A
Symbol
Meaning of Abbreviation
accumulation
Meaning of Symbol in the display
Integrated time
B
beep
Alarm sound setting mode
C
Calibration
Calibration offset setting mode
D
delete program
Deleting a program
display
Sub display switching mode
end
Setting mode for program end
error #
Error code #
F
f. wt (Forced wait)
Forced wait state after the power restoration
H
hold
Hold function mode
hr. mn (hour. minute)
Setting of time (hour, minute)
L
lock
Panel locking mode
Ｍ
mn. dy (month. day)
Setting of the date (month and day)
O
off
Make a function inactive
on
Make a function active
program #
Program number
program
Program mode
program, segment
Ongoing program and ongoing segment
repeat count
Repeat frequency setting mode
real (real time)
repeat
The hour
Repeat command mode
rest time #
Rest for remaining time
ramp level
Ramp level of Segment # (Desired set temperature)
repeat start
Repeat start segment setting mode
ramp time #
r. tim (real time)
Ramp time of Segment #
(Time required to reach the ramp level)
the hour
#
segment #
Segment number
#
soak time
step
Soak time of Segment # (Holding time of the ramp
level)
Not in Ramp Operation
temp
Temperature mode
time
Time mode
wait
wait #
Wait function (Keep the operation until the desired
temperature is achieved)
Wait function of Segment #
year
the Christian era
E
#
P
#
R
#
#
S
T
W
#
Y
35
Flowchart of Operational Procedures
Run “MENU”
Menu key
Program operation
Fixed temperature
operation
When you run the oven in a
programmed operation,
proceeds as follows.
Select the program number
by using either the Πkey or
the  key and then press the
ENTER key.
Displays set
temperatue
A feasible program
number will appear on
the main display.
Set to your desired
temperature by using either
the Œ key or the  key.
The operation start
time will appear on
the main display in
minute.
ENTER key.
Press the ENTER key
Set to your desired operation start
time by using either the Πkey or
the  key.
The operation start
time will appear on the
main display in hour
as of now.
ENTER key
Press the ENTER key
Auto start
Auto stop
The oven can start the fixed temperature
operation after a lapse of the fixed time.
The oven can stop the fixed
temperature operation after a lapse
of the fixed time.
Displays set
temperatue
Set to your desired temperature by using either the
Œ key or the  key and then press
the ENTER key.
Set to your desired temperature by
using either the Œ key or the  key
and then press the ENTER key.
Set to your desired operation start time by using
either the Œ key or the  key.
The operation start
time will appear on
the main display in
minute.
Displays set
temperatue
The operation start
time will appear on the
main display in hour
as of now.
The operation stop
time will appear on
the main display in
minute.
The operation stop
time will appear on the
main display in hour
as of now.
When switching the sub display screens during standby
condition, the remaining time and the hour as of now can appear.
Once started operation, the remaining time (= HOLD), the hour
as of now and the set temperature can be switched on the sub
display.
Set the fan motion to
ON or OFF.
Set the fan motion after
the operation stopped.
Set the fan motion to
ON or OFF.
ENTER key.
Press the ENTER key
Select the wait function
ENTER key.
Set the wait function to ON when you want to hold the fixed
operation for a time that you have set in advance.
Set the wait function to OFF when you want to run the oven
through the operation for a time that you have set in advance.
ENTER key.
36
Press the ENTER key
Press the ENTER key
Program “MODE”
MODE
Main display
See the programming flowchart.
Inputting and deliting
programs (ProG)
Programming
NOTE:If there are no programs, this will not appear.
▲ ▼
ENTER key
Deleting programs
ENTER key
Select the programs number
that you want delete.
*The number of existing programs
will appear on the sub display.
Œ  keys
ENTER key
ENTER key
In case of a period of time
Time/Hour switching
function
In case of the hour
Select the timer mode that you
want to run in hour mode or in a
period of time mode while
running each operation.
Œ  keys
ENTER key
Key lock setting/
releasing function
The key lock will disable you
from doing the key action.
ENTER key
The key action will get
active.
Select the key lock mode.
Œ  keys
ENTER key
The alarm will be sounded.
Alarm buzzer ON/OFF
function
ENTER key
The alarm will not be
sounded.
Set the alarm to be sounded or not if a
problem occurs.
Display
Accumulating time (Accm)
The total time for the power being on can be
shown on the sub display.
Diplay the total time for the
power being on.
It will appear on the sub display.
ENTER key
Date and current hour
setting function (cLoK)
ENTER key
Set the Christian era
by using either theŒ
key or the key.
Set the date and hour.
ENTER key
Calibration off set
function (cAL)
ENTER key
The calibration off set
value that has been set in
advance will appear.
37
Set the hour by using
either theΠkey or
the  key.
Set the date by using
either theΠkey or
the  key.
▲ ▼
Display
ENTER key
ENTER key
Change to your off set value
by using either theΠkey or
the  key.
Flowchart for programming
Segment configuration
: Segments are made up of the
following items, and must be input
in this order.
MODE key
Press
▲ ▼ Key
Call up the program mode.
Temperature
ENTER
Ramp level
key
▲ ▼ Key
Time
Ramp time
Soak time
Call up the program number that you want to
input or edit.
ENTER
key
▲ ▼ Key
ENTER
key
Ramp time
▲ ▼ Key
Rising time
Input Ramp time.
Note: When you run this unit with full power,
input
.
ENTER
Ramp level
key
Target
temperature
When you want to rewrite programs, call up
your desired segment number on the main
display.
Note that this will appear in case of editing.
▲ ▼ Key
Input Ramp level.
Soak time
Time held at ramp
level
ENTER
key
▲ ▼ Key
Wait function Selects
whether
to give priority to
soak time (OFF),
or to hold process
time at ramp level
(ON).
ENTER
key
▲ ▼ Key
Input Soak time.
Note: If there is no soak time (changing
immediately to next temperature), input
0. To hold, select
Select wait function.
ENTER
key
▲ ▼ Key
ENTER
key
▲ ▼ Key
The next segment will appear.
Note: To repeat, press either the key or the
, and select it with
key to display
the ENTER key. Input the segment
number that you want to repeat, and
then do the repeat count.
* Input all the settings in the same way.
When
finished inputting all items, select
for the ramp time, and press the
ENTER key.
ENTER
key
▲ ▼ Key
Settings
finished
38
INSTRUCTION MANUAL
FOR
DRYING OVEN
Model:
DN610H
Version 2
Yamato Scientific Co., LTD.
Congratulations on your selection of Yamato Scientific’s Drying Oven!
Please read these operating instructions, user notes and the warranty card thoroughly before the
initial operation of your drying oven. This will ensure proper operating procedures and extended
life for the unit. Please keep the operating instructions together with the warranty card for easy
access whenever you need them.
Attention: Read the warnings in the operating instructions carefully to familiarize
yourself with the initial operation of your drying oven.
Depending on the extent and nature of danger, the warnings given in these operating instructions
are classified into the following two categories by symbol.
To protect operators from accident -Negligence of this warning may result in a serious accident.
To protect the Drying Oven from damage -Negligence of this warning may result in damage to the Drying Oven. This
warning also gives you tips on performance that are useful in its operation and
maintenance or indicates the common mistakes that operators often make.
TABLE OF CONTENTS
EXPLANATION OF PICTURE DISPLAY ...................................................................................................1
SAFETY PRECAUTIONS .............................................................................................................................2
NOTES TO USERS........................................................................................................................................4
DESCRIPTION AND FUNCTION OF EACH PART...................................................................................4
Main unit.....................................................................................................................................................4
Control Panel ..............................................................................................................................................5
REQUIREMENTS FOR INSTALLATION...................................................................................................7
PRECAUTIONS IN HANDLING................................................................................................................10
OPERATING PROCEDURE .......................................................................................................................13
FIXED TEMPERATURE OPERATION INSTRUCTIONS.......................................................................14
AUTO START OPERATION INSTRUCTIONS .........................................................................................15
AUTO STOP OPERATION METHOD ..................................................................................................................16
PROGRAMMED OPERATION METHOD .............................................................................................................18
SWITCHING FROM ONE OPERATION TO ANOTHER .........................................................................19
METHOD OF USING DISPLAY KEY........................................................................................................20
HOW TO USE THE MODE.........................................................................................................................21
CONTENT OF FUNCTION MENU.......................................................................................................................21
CALIBRATION OFFSET FUNCTION ..................................................................................................................22
Outline of Function ..................................................................................................................................22
Setting The Calibration Offset Function ................................................................................................23
SAFETY DEVICES AND ERROR CODES ................................................................................................24
PURPOSES AND OPERATIONS OF SAFETY DEVICE AND COUNTER-MEASURES................................................24
INDEPENDENT OVERHEAT PREVENTION .........................................................................................25
BEHAVIOR AFTER POWER RESTORATION .........................................................................................26
MAINTENANCE AND INSPECTION .......................................................................................................27
MAINTENANCE PROCEDURE ..........................................................................................................................28
LONG STORAGE AND DISPOSAL......................................................................................................................28
AFTER SERVICE AND WARRANTY ........................................................................................................29
IF A SERVICE CALL IS REQUIRED: ..................................................................................................................29
TROUBLESHOOTING................................................................................................................................30
SPECIFICATIONS ......................................................................................................................................31
WIRING DIAGRAM ....................................................................................................................................32
REPLACEMENT PARTS TABLE...............................................................................................................33
REFERENCE ...............................................................................................................................................34
HAZARDOUS MATERIAL..........................................................................................................................34
LIST OF SYMBOLS IN THE DISPLAY .................................................................................................................35
FLOWCHART OF OPERATIONAL PROCEDURES ................................................................................................36
Run “MENU”.............................................................................................................................................36
Program “MODE” .....................................................................................................................................37
Flowchart for programming.....................................................................................................................38
Explanation of picture display
MEANING OF ILLUSTRATED SYMBOLS
Illustrated Symbols Various symbols are used in this safety manual in order to use
the unit without danger of injury and damage of the unit. A list
of problems caused by ignoring the warnings and improper
handling is divided as shown below.
Be sure that you understand the warnings and cautions in this
manual before operating the unit.
If the warning is ignored, there is the danger of a problem that
may cause a serious accident or even fatality.
If the caution is ignored, there is the danger of a problem that
may cause injury/damage to property or the unit itself.
Meaning of Symbols
This symbol indicates items that urge the warning (including the
caution).
A detailed warning message is shown adjacent to the symbol.
This symbol indicates items that are strictly prohibited.
A detailed message is shown adjacent to the symbol with
specific actions not to perform.
This symbol indicates items that should be always performed.
A detailed message with instructions is shown adjacent to the
symbol.
1
Safety Precautions
WARNING
Do not use the unit in an area where there is flammable or explosive gas.
Never use the unit in an area where there is flammable or explosive gas.
The unit is not explosion-proof. An arc may be generated when the power switch is turned on or
off, and fire/explosion may result.
Always ground the unit.
Always ground the unit on the power equipment side in order to avoid electrical shock due to a
power surge.
If a problem occurs, you should:
If smoke or strange odor should come out of the unit for some reason, turn off the power key
right away, then turn off the earth leakage breaker and the main power. Immediately contact
a service technician for inspection. If this procedure is not followed, fire or electrical shock may
result.
Never perform repair work yourself, since it is dangerous and not recommended.
Do not use the power cord if it is bundled or tangled.
Do not use the power cord if it is bundled or tangled.
overheat and fire may be caused.
If it is used in this manner, it can
Do not process, bend, wring, or stretch the power cord forcibly.
Do not process, bend, wring, or stretch the power cord forcibly.
result.
Fire or electrical shock may
Do not put the power cord under the desk, chair, etc.,
Do not put the power cord under the desk, chair, etc., or through an object.
shock may be caused.
Fire or electrical
Do not run the power cord next to heating equipment such as a heater.
Do not run the power cord next to heating equipment such as a heater.
may melt and fire or electrical shock may result.
2
The cover of the cord
WARNING
Substances that can not be used.
Never use explosive substances, flammable substances and substances that include explosive
or flammable ingredients in the unit. Explosion or fire may occur.
Do not disassemble or modify the unit.
Do not reconfigure the unit.
Fire or electrical shock may be caused.
Do not touch the door during or immediately after operation.
Do not touch the door during or immediately after operation.
caused due to the high temperature.
Severe burning injury may be
CAUTION
During a thunder storm . . .
During a thunderstorm, turn off the power key immediately, then turn off the earth leakage
breaker and the main power. If this procedure is not followed, fire or electrical shock may be
caused.
Periodic check of the safety component.
The independent temperature over-rise prevention device is important safety component. Be
sure to inspect it periodically. (See chapter of INDEPENDENT OVERHEAT PREVENTION on
page 25.)
3
Notes to Users
DESCRIPTION AND FUNCTION OF EACH PART
Main unit
Door handle
Power switch
(Earth leakage breaker)
Control panel
Exhaust port
Power cable
4
Control Panel
⑪
⑪f
⑪
⑪e
⑪b
⑪c
⑪
⑯
⑭
⑫
⑨
②
①
④
③
⑮
⑤
⑧
(1) POWER key:
(2) MODE key:
(3) DISPLAY key:
(4) MENU key:
(5) ENTER key:
(6)/(7)
(UP/DOWN) key:
(8) ESCAPE
key:
(9) Main Display:
(10)Sub Display:
(11)Operation monitor:
a) (11) STANDBY lamp:
b) (11) Temperature
pattern lamp:
c) (11) OVER lamp:
d) (11) TROUBLE
indicator lamp:
⑥⑦
⑩
⑬
Key to change over the controller from the standby mode to the
operation mode or from the operation mode to the standby mode.
Key to select a function from program input, edit, delete modes,
hour/time setting, change-over mode, and other functions.
Key to change-over the display content of the sub display (10).
Display content is changed over to set temperature, remaining
time, hour, execution segment No.
Key to select the operation mode. Each mode of fixed
temperature, auto-start, auto-stop and program operation can be
selected.
Key to determine the input value of set value (temperature, time,
hour, etc.), selection mode, execution segment No. etc.
Key to change set value (temperature, time, hour, etc.) and to
choose a selection from various parameters on the function menu.
Key to cancel the latest entry and recover the status that was valid
prior to the making the latest selection.
It displays temperature measurements, set values (temperature,
time, hour, etc.), program information, error information, etc.
It displays set temperature, remaining time, current hour and
execution segment No. etc.
It indicates an operation mode.
It flashes to indicate that the instrument is in the preoperational
standby mode.
It illuminates to indicate the heat treatment process pattern
executed by the controller with flashing light indicating the point
currently in execution.
It flashes to indicate the end of auto-stop or program operation.
It blinks when an error is detected and displays the corresponding
code for that particular problem.
5
e) (11)REMOTE operation
indicator lamp:
f) (11)KEY LOCK
indicator lamp:
(12)Operation menu
indicator lamp:
(13)Sub display menu
indicator lamp:
(14)HEAT ON indicator
lamp
(15)TIME indicator lamp:
(16)Independent
Temperature
Overheating Prevention
Device:
It illuminates when the instrument is put into remote operation
(optional) and displays the word “REMOTE.”
It illuminates to indicate that the operation panel key lock function is
in operation.
It illuminates to indicate the active operation mode in the operation
menu.
It illuminates to indicate the item (set temperature, remaining time,
hour or execution segment) shown in the sub display.
It illuminates when the heater is on.
It illuminates when the operation starting time of the auto-start and
the operation completion time of the auto-stop is set in the hour
setting mode.
Setting the instrument to the operational temperature of the
independent over rising prevention.
6
REQUIREMENTS FOR INSTALLATION
Do not use the unit in an area where there is flammable or explosive gas.
Never use the unit in an area where there is flammable or explosive gas. The unit is
not explosion-proof. An arc may be generated when the power switch is turned ON
or OFF, and fire/explosion may result.
Explosive gas
Flammable gas
Always ground the unit.
z Connect the grounding cable to your ground conductor or ground terminal.
z Do not forget to ground the Oven, to protect you and the unit from electrical shock
in case of power surge.
z Do not connect the grounding wire to a gas pipe, or by means of a lightning rod or
telephone line. A fire or electrical shock will occur.
NOTE: The oven has not a plug connected because of the 200V specification.
Choose a correct power distribution board.
z Choose a correct power distribution switchboard or receptacle that meets the
oven’s rated electric capacity.
Electric capacity
AC 200 V, single phase 21A
z Do not connect the oven to an outlet that differs from the above specifications
because a fire or electrical shock will occur.
Supply connections for the oven
z Request the supply connection for the 200V specifications from a licensed
electrician.
z Failure to have this operation complete by certified personnel will cause a fire or
electrical shock during Oven operation.
Install the Oven on a level area.
z Do not installation the oven on a non level surface. This will cause hazards to the
operator and create problems during actual operation.
7
Choose a proper place for installation.
z Do not install the oven in a place where:
♦
♦
♦
♦
♦
♦
Flammable gas or corrosive gas is generated.
Ambient temperature exceeds 35°C.
Ambient temperature fluctuates violently.
There is direct sunlight.
There is excessive humidity and dust.
There are constant vibrations.
z Keep the following clearance around the oven.
Or more
Or more
Or more
After installed, you should:
z It may cause injure to a person if this oven falls down or moves by the
earthquake and the impact, etc..
z To prevent, take measures that the unit cannot fall down.
z Secure the unit by putting the stoppers on the casters.
8
Handling of power code.
z Do not use the power cord if it is bundled or tangled.
can overheat and fire may be caused.
If it is used in this manner, it
z Do not process, bend, wring, or stretch the power cord forcibly.
shock may result.
Fire or electrical
z Do not put the power cord under the desk, chair, etc., or through an object.
or electrical shock may be caused.
z Do not run the power cord next to heating equipment such as a heater.
cover of the cord may melt and fire or electrical shock may result.
Fire
The
z When the power cord is damaged (exposure of the core wires, disconnection,
etc.), turn off the power key right immediately, then turn off the earth leakage
breaker and the main power. Contact customer service for a replacement
immediately. If this procedure is not followed, fire or electrical shock may be
caused.
Caution in setting shelves
z Do not use any shelves but the attached ones.
If it is used in this manner, the oven cannot occasionally regulate temperatures
properly.
z Put the attached shelves on the shelf brackets fitted to the chamber when you use
the oven.
9
Precautions in handling
Substances that can be used
z Never use explosive substances (shown on page 34), flammable substances
(shown on page 34) and substances that include explosive or flammable
ingredients in the unit. Explosion or fire may occur.
Do not put the foreign substances in the oven.
Do not put a foreign substances such as metals or flammable substances in the
opening of the unit (ventilation hole and exhaust port, etc.). If this procedure is not
followed, fire, electrical shock or burn may result.
If the foreign substances enter the unit, turn off the earth leakage breaker
immediately and contact a service technician for inspection. If this procedure is not
followed, fire, electrical shock or burn may result.
Caution in taking out samples
During and immediately after operation, the internal surfaces of the chamber and the
door are extremely “HOT." To prevent injury, take out the samples when the
chamber has cooled down or wear gloves while the chamber is still hot.
When you open the door during working at the high temperature.
Do not touch the internal surfaces of the chamber and the door when you will open
the door, because they are extremely hot.
To open the door while the chamber is still hot may cause the malfunction of a fire
detector if it is installed near the oven.
Do not touch heated parts.
Do not touch the door during or immediately after operation. Severe burning injury
may be caused due to the high temperature.
Do not climb on the oven
Do not climb on top of the oven because it will fall down and break.
Failure to observe this caution may cause injury to a person.
Do not put anything on the oven
Do not put anything on top of the oven because they will fall and result in injury to a
person.
10
Caution about the temperature range.
Use the oven in the range of 40°C to 210°C.
When you use the oven for the first time
During the initial operation, the oven may occasionally generate an odor especially
when high temperatures are reached. This odor is normal and does not signal a
problem with the oven. The adhesive on the insulation melting causes the nature of
the odor.
About the temperature in the chamber
Temperature display indicates the sensor temperature installed in the unit, however it
does not always correspond to the temperature of the sample when the sample
volume is very large or when the temperature is on the increase.
Caution about a drenched sample
z When using a very wet sample, try to drain it as much as possible before putting it
in chamber.
Caution about a powdery sample and the loading of samples
There are times when a powder sample is scattered by the sudden decompression
operation or purge operation. When performing decompression or purge, open the
valve very slowly.
It occasionally takes a long time before the chamber reaches the target temperature if
the camber is congested with samples or a sample with the large specific heat is in it.
In such cases, reduce samples. Moreover, note that the temperature display
occasionally unsettle when you process an exothermic sample.
Distribute samples
z
z
Each shelf can carry a uniform load of 15 kg (33 lb.). When you place samples
on a shelf, distribute them evenly over the shelf area.
If a shelf is congested with samples, the oven occasionally cannot regulate
temperatures properly. To ensure the oven’s temperature accuracy, there should
be open space of at least 30% on each shelf.
Never use corrosive samples
Most parts are made of stainless steel (SUS304). However, strong acid occasionally
corrodes even stainless steel. Besides this, the silicone rubber packing is also
vulnerable to acid, alkali, oil and halogens' solvents
11
Do not place any samples on the bottom of the chamber
z Do not place any samples on the bottom of the chamber to heat,
because it affects the temperature control of the oven.
Sample
z Always put the samples on the attached shelves. Place sample so that
it does not touch the interior wall of the chamber.
z Set the shelves on the shelf brackets that will accommodate the size of
the sample.
During a thunder storm
During a thunderstorm, turn off the power key immediately, then turn off the
earth leakage breaker and main power. If this procedure is not followed,
fire or electrical shock may be caused.
In case of power failure
Once the power supply has been cut off due to power failure, and then the
power supply is restored, the oven will resume running.
When you open and shut the door
Do not put your hand either face near the door when you open and shut
the door. Failure to observe this caution may result in injury because the
door hits your hand or face.
12
Operating Procedure
When prepared completely, proceed as follows:
1. Turning on of power supply
2. Selection of operation menu
• Press the MENU key several times to select
• Turn on the earth leakage breaker.
desired operating method.
• It allows you to enter each parameter into a
• The present time is shown on the sub display.
flashing menu.
• Push the POWER key in the operation panel.
• When once the power is on, this oven becomes
a standby state. Under such a condition, every
operation mode can be selected by pushing the
MENU key.
3. Explanation of operation menu
Fixed
Temperature
: It is an operation method to bring the oven to the desired temperature and
keep it steady.
Auto stop
: It is an operation method to stop a fixed temperature operation when
reached the set time or hours.
Auto start
: It is an operation method to start the fixed temperature operation when
reached the set time or hours.
Program
: It is an operation method that can start or stop an operation either when
reached the set time or hours. Moreover, it can change the temperature
when reached the desired time and repeat to do that.
13
FIXED TEMPERATURE OPERATION INSTRUCTIONS
Selection of operation
menu
Input of set temperature
• Push the ENTER key after
• Push the MENU key and
select the fixed temperature
operation.
making a sub-display display
an arbitrary set temperature
pushing ▲▼ keys.
Changing the set
temperature when fixed
temp operation is in
progress
• Push
either the ▲ key or
the ▼ key to display the
desired temperature on the
main display and push the
ENTER key.
Push the MENU key.
Press either the ▲key or the ▼ key
several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired set temperature will
appear on the main display.
The lamp of the FIXED TEMP blinks.
• The temperature set last time
is blinking and enters the state
that a set temperature can be
input in a sub-display.
Press the ENTER key.
• The oven will start to run the
fixed temperature operation
to the renewed temperature.
Push the ENTER key.
• The oven will start to run the
fixed temperature operation
to the renewed temperature.
14
AUTO START OPERATION INSTRUCTIONS
Selection of operation menu
Inputting the set temperature
• Select AUTO START mode by
• Press either the ▲ key or
pushing the MENU key.
the ▼ key to display the
desired temperature on the
main display and push the
ENTER key.
Inputting the desired set
time
• Press either the ▲ key or
the ▼ key to blink start time
(or the hour) on the main
display, and press the
ENTER key.
Push the MENU key.
The operation menu lamp of an AUTO
START blinks.
•
Press either the ▲ key or the ▼ key
several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired start time (or hour)
will appear on the main display.
will appear on the
sub display and the desired
temperature can be input.
Sub display
Press The ENTER key.
Press the ENTER key.
•
will appear on the
sub display and the operation
start time can be input.
• The STANDBY lamp of the
operation monitor blinks.
• The operation will be in standby
condition.
• After reaching the set time
(or hour), the oven will start
to run the auto start
operation to the renewed
temperature.
15
Auto Stop Operation Method
Selection of operation menu
Inputting the set temperature
• Press the MENU key and
• Push either the ▲ key or
select the auto stop operation.
the ▼ key to blink the
desired temperature on the
main display and push the
ENTER key.
Inputting the desired set
time
• Push either the ▲ key or
the ▼ key to blink your
desired time (or hours) for
operation stop on the main
display, and press the
ENTER key.
Press the MENU key.
The menu lamp of an AUTO STOP
blinks.
•
Press either the ▲ key or the ▼
key several times.
Then, the desired set temperature will
appear on the main display.
Press either the ▲ key or the ▼
key several times.
Then, the desired stop time (or hour)
will appear on the main display.
will appear on the
sub display and the desired
temperature can be input.
Sub display
Push the ENTER key.
The main display will light up to
indicate the set temperature you have
chosen.
Push the ENTER key.
After about 1 second
•
will appear on the
sub display and the operation
stop time can be input.
16
•
will appear on the
sub display and you can
chose the wait function to be
activated or not.
Selection of wait function
• Press either the ▲ key or the
▼ key to indicate the wait
function (ON or OFF) on the
main display. Then press
ENTER key.
Working conditions of timer
• Auto Stop timer activates when:
1. The wait function is on.
It starts when the set temperature has
reached the target value.
2. The waiting function is off or the time
setting represents hours.
Press either the ▲ key or the ▼ key
several times.
Either ON or OFF will appear on the
main display.
(activate)
It starts right after the auto stop
operation is started.
(inactive)
Press the ENTER key.
• This operation activates the
auto stop operation.
17
Programmed Operation Method
Selection of operation
menu
Input of execution
program number
Input of time
• Press either the ▲ key or
• Press the MENU key and
select
the
operation.
• Press either the ▲ key or
programmed
the ▼ key to indicate an
desired program number on
the main display, and press
the ENTER key.
the ▼ key to blink your
desired operation start time
(or hour) on the main display,
and press the ENTER key.
Press the MENU key.
The operation menu lamp of the
PROGRAM blinks.
•
Press either the ▲ key or the ▼ key
several times.
The program number will appear on
the main display.
NOTE: If no programs have been set,
―――― is blinking.
See the Operating Instructions
for Programmable Controller
to set a new program.
will appear on the
sub display and the execution
program number can be input.
Press either the ▲ key or the ▼ key
several times.
The desired set time will appear on
the main display.
Push the ENTER key.
Push the ENTER key.
• The standby lamp on the
•
will appear on the
sub display and the operation
start time can be input.
18
operation monitor blinks.
(Operation is in STANDBY
MODE)
• The operation will start after
the set time is up.
SWITCHING FROM ONE OPERATION TO ANOTHER
This instrument can switch to a different operation mode without stopping the current program no
matter what mode it is in, fixed temperature operation, auto-start/stop operation, and program
operation.
Selection of operation menu
• Press the MENU key several times until the
desired operation menu lamp flashes on the
Operation Menu.
• Since the current operation has not stopped, the
operation menu lamp is also lit.
• On the Operation monitor -- the temperature
pattern indicator lamp blinks with the current
segment being executed.
Press MENU key several times.
• This status allows you to enter each parameter
into blinking or lighting operation menu.
When the fixed temperature operation is selected
ƒ The main display shows the current internal
temperature.
ƒ The sub-display flashes the temperature set by the
previous fixed temperature operation.
When auto-start operation is selected
ƒ The main display flashes the temperature set by the
previous auto-start operation.
ƒ
The sub-display shows
(Temp.)
When auto-stop operation is selected
ƒ The main display flashes the temperature set by the
previous auto-stop operation.
ƒ
The sub-display shows
(Temp.)
When program operation is selected
ƒ The main display flashes the previously set program
number.
ƒ
The sub-display shows
(Program)
The lamp blinks or lights.
• Now operate according to the operation method you have chosen, see that section of this instruction
manual.
19
Method of using DISPLAY key
The display content of the sub display can be changed over by turns when pushed the DISPLAY
key.
Operation mode
Sub display
Fixed temperature
operation
Set temperature
Hour
Remaining time
Standby
Hour
Auto start
operation
Set temperature
During operation
Remaining time (*1)
Hour
Set temperature
During operation
Auto stop
operation
Remaining time (*2)
Hour
After time is up
Hour
Remaining time
Standby
Hour
Set temperature
Remaining time
Program operation
During operation
Hour
Execution segment (*3)
Hour
After finished
*1: HOLD is displayed.
*2: When the wait function is set to on,
is displayed in the waiting status.
*3: The DISPLAY key will enable to show the rest of the repeat count while the repeat operation.
20
How to use the MODE
Content of function menu
This controller has the other functions shown bellow.
• Press the MODE key and display your desired
function on the main display by pushing either the
key or the
key. Each function will appear by
turns whenever pushing the
keys.
Press the mode key.
Select with the ▲ key or
the ▼ key.
Main display
Function
Inputting and editing
programs
To input and edit the program.
To delete existing programs that are no longer necessary.
Confirmation of the program contents should be performed
prior to deleting and in accordance with Programmed
Operation Method.
To input either an hour or a period of time during time
setting process in the various operation modes -Switching time
auto-start/stop, and program operation.
setting mode.
It is set to the time (a period of time) setting mode when the
product was shipped from the factory.
To set or release the key lock function.
This function is for protecting wrong key actions during the
operation or while being in the standby state.
Setting and releasing
Once set to ON, the key lock will disable you from doing
the key lock.
the POWER, MENU, ENTER, and DELETE key action.
If the key lock function is set, the KEY LOCK lamp on the
operation monitor is lit.
To select whether you want to activate the alarm buzzer or
Alarm buzzer
not when an error occurs.
ON/OFF function.
Deleting the
Program.
Accumulating time
display function
Hold function
Date and current
hour setting function.
Calibration offset
function
To display the total duration that the POWER key is on,
within the range of 0 to 49999 hours.
To hold the operation that is currently running. This function
will get active only when you run the oven in auto-start/stop
or program operation mode (includes the standby state).
In addition, it will work when the setting of the operation
start time for auto-start and program operation as well as
the operation end time for auto-stop are set in the form of
“Time” and not in the form of “Hour.”
To set the date and hour.
To conform the display temperature to the measurement
temperature of a voluntary point in the chamber at a
voluntary temperature. Details are described on page 22
21
Calibration Offset Function
Outline of Function
In the controller, the relationship between the temperature
T detected by the sensor and the display temperature of
the operation panel D is expressed by the equation of the
line which passes the two points (T0, D0) and (TS, DS)
DS
shown in Fig. 1.
Here, T0 is the sensor detecting temperature when the chamber
y=ax+b
central temperature becomes the zero adjusting temperature
D0
(normally room temperature is adopted) D0 at the time of no load, TS
is the sensor detecting temperature when the chamber central
temperature becomes the span adjustment temperature (normally
T0
TS
working maximum temperature is adopted) DS at the time of no load
Sensor detection temperature
in the same way.
As it is clear from the facts above, conforming of the chamber central
Fig. 1
temperature and the display temperature is guaranteed only when
there is no load and at two points shown above. In other words, it is
possible for a temperature measured at a point in the chamber does not conform to the display temperature
of the operation panel at a voluntary temperature without load.
This is the function to move the line which passes above two points to the Y axis direction in parallel
(increase or decrease y intercept of the line). The parallel movement amount including a sign is defined as
the calibration offset. This function can conform the display temperature of the operation panel to the
measurement temperature of a voluntary point in the chamber at a voluntary temperature.
Display temperature
(Controlled temperature)
In Fig. 2, DSV is a display temperature of the
operation panel under the condition that the
temperature in the chamber is constant for a set
temperature. It is natural to say that this value is
equal to the target set temperature. DPV is a
measurement temperature of a voluntary point in the
chamber under this condition.
The difference
between DPV and DSV including the sign is defined
as the calibration offset. Therefore offset is shown
as below.
△DCAL＝DPV－DSV
Equation 1
Display temperature
(Controlled temperature)
Parallel movement
DSV
△DCAL
DPV
Ti
TV
Sensor detection temperature
In Fig. 2, ΔDCAL becomes the negative value since the target
set temperature DSV is larger than the actually measured
In order to conform the display
temperature DPV.
temperature to the actually measured temperature, let the controller to recognize that the temperature in the
chamber differs from the target set temperature by ΔDCAL.
Fig. 2
NOTE: Setting Tolerance of Calibration Offset
♦
♦
The calibration offset can be set within ±5% of the maximum working temperature of the oven.
(Therefore, the setting tolerance of the calibration offset is ±19°C.)
Initial off set value has been set to 0°C when shipping.
22
Setting The Calibration Offset Function
This function can be activated when the controller is in the condition of accepting the MODE key.
EX. Bring the oven to the target set temperature 100°C and allow it to reach the steady state. After
then, measure the temperature at a point in the chamber. If it shows 97°C when the main display
shows 100°C, you can conform your measuring value to the one on the display by using the
calibration offset function.
Calibration offset ΔDCAL is obtained from the
Equation 1 (page22) as shown below.
△DCAL＝97℃－100℃＝－3℃
Procedures to set the calibration offset ΔDCAL to the controller are shown as below.
Setting and changing the calibration offset value
• Push the MODE key, and then push the
main display.
key or the

key several times to display
Push the
key or the
on the
key several times
• The sub display shows the calibration offset value that has been set the last time.
NOTE: When the unit is shipped from the factory, the sub-display shows 0 as the
calibration offset value.
Push the ENTER key.
• The main display flashes the preset calibration offset value.
⇒ In this state, the set value of the calibration offset can be changed.
• The sub display shows
.
Push the key or the key several times
• Push either the
key or the key to change the value on the main display to your desired value
(calibration offset value to be set newly).
When the changing is completed, push the
ENTER key.
• The changed value is entered and both the main and the sub displays return to the display mode just
before pushing MODE key. The controller starts the temperature controlling operation in order to
make the difference zero, since the difference is generated between the target set temperature and
the temperature in the chamber by the changing of the calibration offset value.
23
Safety Devices and Error Codes
Purposes and Operations of Safety Device and Counter-measures
This instrument incorporates an automatic diagnosis function built in the controller and safety
devices independent of the controller. The purposes and operations of the safety devices and
countermeasures are shown in the Table below. When an abnormal condition occurs, an error
code is displayed in the main display. Immediate action should be taken according to the specific
counter-measures.
Safety Device
1. Earth leakage breaker
Display
No Display
2. Sensor malfunction
detector
3. Triac circuit detector
4. Disconnected heater circuit
detector
5. Independent overheating
prevention
TROUBLE lamp flashes.
flashes.
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
flashes.
6. Main relay malfunction
detector
7. POST function*
TROUBLE lamp flashes
flashes.
TROUBLE lamp flashes
,
,
Cause & Counter-measures
• Power circuit interrupted
• Erases all displays
⇒ Report to our service office and
check the cause of the problem.
• Break in temperature sensor circuit.
⇒ Report to our service office.
• Short circuit in triac.
⇒ Report to our service office.
• Heater circuit is disconnected.
⇒ Report to our service office.
• Incorrect setting of the independent
overheating prevention.
⇒ Set correctly.
• Heating of sample
⇒ Reduce the amount of the sample.
• Malfunction of the independent
overheating prevention circuit.
⇒ Report to our service office.
• A malfunction of the main relay.
⇒ Report to our service office.
• Contact Yamato Sciectific’s
Technical Service Department.
flashes.
8. Automatic overheating
preventive function
9. Key lock
10. Memory backup circuit
11. Door switch
z
No Display
Key lock display lamp lights up
No Display
flashes
• Heating of samples
⇒ Reduce amount of samples
•
This function prevents the disruption
of operation due to incorrect
operation. Leave it on during
operation. (See section in this
manual for setting and resetting
methods on page 21).
• It is not the fault.
⇒ When opened the door,
will
flash on the sub display and the
heater circuit will be cut off and the
fan will stop for safety. Once closed
will go out and
the door,
the heater circuit and the fan will
resume working.
POST (Power On Self Test) function checks the microprocessor, memory surrounding LSI, surrounding
circuit of the controller every time “POWER” key is turned ON. This is the function for checking that the
controller won’t have a fatal fault before starting the operation.
24
INDEPENDENT OVERHEAT PREVENTION
There are two safety devices in this unit: the auto-overheating preventive function of the
controller (automatic recovery) and the independent overheating prevention (manual recovery).
Circuits and sensors that are independent from the controller configure them. These safety
devices for the temperature overheating prevention protect the instrument in a fail-safe method.
Setting the Temperature Range and Function
Setting
Temperature:
Input Method:
Function:
0 to 399oC
Three integer digital switch. Turn the drum of each column and set the desired
value. The first integer can only be from 0 to 3 for the hundred columns.
Heater output is cut off when the measured temperature gets higher than the set
temperature of the independent overheating prevention. The function is active
when the earth leakage breaker is ON.
When the independent overheating prevention is activated, is flashing on the
main display with the TROUBLE lamp flashes. When the independent overheat
prevention is active while the heater is in the temperature rising process, etc.,
and flash alternately on the display.
Activation/Setting Method
1. Set the independent overheating prevention 15oC higher than the set temperature of the main
unit.
2. When setting the proper value to protect the sample, be sure it is well above room temperature,
and set it at least 15oC higher than the maximum temperature set value of the temperature
pattern of the program.
3. When the independent overheating prevention is activated improperly by changing the setting
of the independent overheating prevention lower than the internal temperature or by continuing
operation when the setting on the unit is too low, turn off the earth leakage breaker to reset the
unit and perform the setting again.
If it is activated by another reason, see chapter of Safety
Devices and Error Codes on page 24.
Precautions
1. Only 0 to 3 can be set for the column of hundreds of the digital switch by the stop mechanism;
however, if forced to change it to a value higher than 3, it will damage the unit.
2. Set temperature can change by touching the setter when cleaning.
set temperature is correct after cleaning or before operation.
25
Always confirm that the
Behavior after Power Restoration
In case of power failure during operation, the controller resumes the following operations after the power
restoration.
In case of power failure during the program operation
The controller automatically resumes the program operation where it left at the power shutdown. In case
that the temperature inside the chamber is outside the specified temperature range based on the setpoint
temperature, the controller goes to the FORECED WAIT STATE until the temperature inside the chamber
comes back to the specified temperature range. When you select the display of the remaining time by
pushing the Display key in this condition, the sub display shows
.
The timer built-in the controller does not count as running time for a period of power failure.
In case of power failure during the Auto-Stop operation
The controller automatically resumes the Auto-Stop operation where it left at the power shutdown. In
case that the temperature inside the chamber is outside the specified temperature range based on the
setpoint temperature after the power restoration, the controller goes to the FORECED WAIT STATE until
the temperature inside the chamber comes back to the specified temperature range. When you select the
display of the remaining time by pushing the Display key in this condition, the sub display shows
. (Forced Wait)
In case that the operation stop time is set in a period of time, the timer built in the controller does not
count as running time for a period of power failure.
On the contrary, in case that the operation stop time
is set in hours, the timer built in the controller counts as running time for a period of power failure.
When the operation stop time reaches during power failure, the controller stops running just after the
power restoration.
In case of power failure while the controller is in standby condition
In case that the operation start time is set in a period of time, the timer built in the controller does not
count as standby time for a period of power failure.
On the contrary, in case that the operation start
time is set in hours, the timer built in the controller counts as standby time for a period of power failure.
When the operation start time reaches during power failure, the controller starts running just after the
power restoration.
In case of power failure during the fixed temperature operation and a soak period of
the Auto-Start operation
The controller resumes running toward to the preset temperature after the power restoration.
26
Maintenance and Inspection
Do not disassemble and modify the oven.
z
Do not disassemble the oven. There are parts in the unit with high voltage;
therefore, if the unit is disassembled, electric shock and injury may result.
Ask the Yamato Scientific office for inspection, adjustment, and repair of the inside of
the unit.
z Unauthorized modification will be hazardous and cause problems in the operation
of the Oven.
Modification
Maintenance Precautions
z Before starting inspection or maintenance, disconnect the power plug from the
receptacle.
z Conduct inspection and maintenance only after the oven has cooled down.
z When you remove dirt or stains from the unit’s resin parts and the control panel,
use a soft wet cloth. Do not use benzene, thinner, cleanser or a hard brush; it will
cause deformation, qualitative deterioration and/or discoloring of the components.
Periodic inspection of the safety component.
z The independent temperature over-rise prevention device is important safety
component. Be sure to inspect it periodically.(See chapter of Maintenance
Procedure on page 28)
If you have any questions, contact our sales representative in your vicinity or our service office.
27
Maintenance Procedure
Operation Check of Independent Temperature Overheating Prevention Device
z After executing the fixed temperature operation at the set temperature 0°C, set the operation
temperature of the Independent Temperature Overheating Prevention Device to 0°C.
z Under normal circumstances, the heater circuit is cut off in a few seconds and the TROUBLE
lamp and
flashes at the same time, and the alarm buzzer sounds if the alarm
buzzer function is ON.
z After confirming, turn off the earth leakage breaker once, and then return the setting of the
Independent Temperature Overheating Prevention Device to the proper value. Turn the earth
leakage breaker back ON.
Always perform inspection before a long continuous operation or an unattended
operation.
Long Storage and Disposal
When you do not use the oven for a long period of time.
Disconnect the power cable from the power switchboard.
When you dispose of the oven.
Do not leave it where children can access.
to disable the door locking system.
28
Remove the knob and hinges of the door
After service and WARRANTY
If a Service Call is required:
If a Service Call is required
Warranty Card (attached to your Oven)
zIf a problem occurs with the Drying
Oven, record the error code on the
display and stop the operation
immediately, turn off the power switch,
and disconnect the power plug from the
receptacle. Contact our sales or
service representative.
zPlease fill out completely and return the
bottom portion of the warranty card
when the unit is received. The
completed top portion is your
Registration Card that should be
retained for your records.
zCheck the warranty card or the name
plate of your Drying Oven and give us
the information below.
•
Model of your oven;
•
Serial product number of your
oven;
•
Date of purchase; and
•
Problem with your oven (as
detailed as possible).
zWarranty period is one (1) year after
the date of your purchase. During this
warranty period, we will offer free repair
service on the basis of the conditions
provided on the warranty card.
zIf you need repair service after
expiration of the warranty period,
contact our sales or service
representative in your vicinity or service
office for advice.
Minimum Inventory Period of Repair Parts
Repair parts will be available for at least 5 years after termination of our production of
Drying Oven Series. Repair parts mean the parts that are necessary to maintain the
performance of the ovens.
29
TROUBLESHOOTING
Problem
No display of current hour in the
sub-display at the activation of the earth
leakage breaker.
Temperature fluctuates during the
operation
•
•
•
•
•
It takes too much time for temperature to
rise.
•
Cause/Solution
Check if the power cable is firmly
connected to a receptacle.
Check for power failure.
Does ambient temperature fluctuate
violently?
Are there too many samples in the
chamber?
Are the samples too moist?
Are there too many samples in the
chamber?
30
SPECIFICATIONS
Model
Method
Performance:
Operating temperature
Temperature stability*1
Temperature Uniformity
Time to reach max. temp.*1
Structure:
Exterior
Interior chamber
Insulating material
Heater nominal capacity
Fan
Cable port
Exhaust Port
Controller:
Temperature control method
Temperature setting method
Temperature indicating method
Other indication
Timer
Operation function
Additional function
Heater circuit control
Sensor
Safety device
DN610H
Forced Ventilation
４０ ～ ３６０℃
±０．２℃（＠３６０℃）
±３．０℃（＠３６０℃）
Approx. 60 min.
Cold rolled steel plate with baked-on melamine resin finish
Stainless steel (SUS304)
Glass wool and Ceramic fiber
4.0kW
Sirocco fan, Output:10W×2
Inner diameter 30 mm (right side)
Inner diameter 30 mm x 2 (rear face)
PID control by microprocessor
Digital setting method by
keys (resolution: 1°C)
Digital display by green LED (resolution: 1°C)
Temperature pattern LED indication that shows operation indication
1 min. to 99 hrs. 59 min. or 100 hrs to 999 hrs
(Timer resolution: 1 min. or 1 hr.)
Fixed temperature operation
Auto-start/Auto-stop operation
Program operation (16 segments, repeat, etc.)
Calendar timer function (actual hr. timer within 24 hrs.)
Integrating time function (Integrated hr. up to 49999 hrs. can be
measured.)
Time indication (The present time is indicated.)
Calibration offset function
Triac zero cross system
K thermocouple (double sensor)
Earth leakage breaker with the over current protector
Self-diagnostic function (sensor abnormality, heater disconnection and
Triac short circuit detection; automatic temperature over-rise prevention)
Key lock function
Independent Temperature Overheat Prevention device
(Digital switch input system, setting temperature range: 0 to 399°C)
620 mm × 600 mm × 600 mm
790mm × 845mm × 1080mm
223 l
Approx. 120 kg
AC 200 V, 50/60Hz, 21A single phase
Internal dimensions (WxDxH)*2
External dimensions (WxDxH)*2
Capacity
Weight
Power Requirements
Accessories:
2 sets
Shelf / Shelf brackets
For exclusive use of this oven and the controller: each one
Instruction manual
NOTES: *1. The values written on the chart have been measured with no sample and both exhaust ports
closed in ambient temperature of 20°C.
*2. Both of internal and external dimensions do not include the one of protruding parts.
31
WIRING DIAGRAM
Symbol
CT1
ELB
Part Name
Current Transformer
Earth leakage breaker
Symbol
PCB3
PCB4
FM1
H
LS
P1,2
PCB1
PCB2
Fan motor
Heater
Door switch
Terminal block
PIO board
PLANAR board
PI1,2
SSR1,2,3
SW
Tf
TH
X1
32
Part Name
Power board
Independent overheat
prevention
Photo-interrupter
Solid-state relay
Membrane keypad
Transformer
Thermocouple
Relay
REPLACEMENT PARTS TABLE
Symbol
CT
ELB
FM
H
P
P1,2
PCB1
PCB2
PCB3
PCB4
PI1,2
SSR1
SSR2
SSR3
SW
Tf1
TH
X1
Part Name
Current Transformer
Earth leakage breaker
Fan motor
Heater
Power code
Terminal block
PIO board
PLANAR board
Power board
Independent overheat
prevention
Photo-interrupter
Solid-state relay
Solid-state relay
Solid-state relay
Membrane keypad
Transformer
Thermocouple
Relay
Code No.
2-17-001-0002
Specifications
CTL-6-S-400
2-06-005-0012
BJS30-3(AC200V)
2-14-000-0003
REK42M-4CCW, AC200V
DN63H-30320
AC200V 2000W
2-13-001-0010
2-07-023-0002
1-24-000-0024
1-24-000-0059
1-24-000-0025
1-27-001-0002
T3 - 3d
M011-0FX 4P
Type 1
QKB-0
1-21-001-0002
LT00028427
LT00028425
LT00028423
1-01-320-0008
2-18-000-0023
1-16-001-0042
2-05-000-0010
TLP802
SSR-01A
SSR-01B
SSR-01
Type 4H
AC200V
K thermocouple (double sensor)
HE1a-DC12V
33
Reference
HAZARDOUS MATERIAL
Explosives
Explosives
Substances
Combustible
Substances
Oxidants
Flammable
s
Ignitable
Substances
Combustible
Gases
1. Nitroglycol, Nitroglycerin, Nitrocellulose, and other explosive
nitric esters.
2. Trinitrobenzens, Trinitrotoluene, Picric acid, and other
explosive nitro compounds.
3. Peracetic acid, Methyl ethyl ketone peroxide, Benzoyl
peroxide, and other organic peroxides.
Metallic lithium, Metallic potassium, Metallic sodium, Yellow
phosphorus, Phosphorus sulfide, Red phosphorus, Celluloid,
Calcium carbide, Lime phosphate, Magnesium powder,
Aluminum powder, and other ignitable metal powders and sodium
dithionite (hydrosulfite).
1. Potassium chlorate, Sodium chlorate, Ammonium chlorate,
and other chlorates.
2. Potassium perchlorate, Sodium perchlorate, Ammonia
perchlorate, and other perchlorates.
3. Potassium peroxide, Sodium peroxide, Barium peroxide, and
other inorganic peroxides.
4. Potassium nitrate, Sodium nitrate, Ammonia nitrate, and other
nitrates.
5. Sodium chlorite and other chlorites.
6. Calcium hypochlorite and other hypochlorites.
Ethyl ether, Gasoline, Acetaldehyde, Propylene chloride,
Carbon disulfide, and flammable substances with a flash point
below minus 30ºC.
Normal hexane, Ethylene oxide, Acetone, Benzene, Methyl
ethyl ketone, and flammable substances with a flash point
between minus 30ºC and 0oC.
• Methanol, Ethanol, Xylene, Pentyl acetate (amyl acetate), and
inflammable substance with a flash point between 0ºC and
30ºC.
• Kerosene, Light oil, Turpentine oil, Isoamyl alcohol, Acetic acid,
and flammable substances with a flash point between 30ºC
and 65ºC
Hydrogen, Acetylene, Ethylene, Methane, Ethane, Propane,
Butane, and other gases that are flammable under 1 atmospheric
pressure at 15ºC.
(Quoted from “Addendum Table1 of Code of Work Safety and Hygiene Standard”)
34
List of Symbols in the display
The oven has the controller with the 4-digit LED display. The meaning of symbols in the display is as follows:
Capital
A
Symbol
Meaning of Abbreviation
accumulation
Meaning of Symbol in the display
Integrated time
B
beep
Alarm sound setting mode
C
Calibration
Calibration offset setting mode
D
delete program
Deleting a program
display
Sub display switching mode
end
Setting mode for program end
error #
Error code #
F
f. wt (Forced wait)
Forced wait state after the power restoration
H
hold
Hold function mode
hr. mn (hour. minute)
Setting of time (hour, minute)
L
lock
Panel locking mode
Ｍ
mn. dy (month. day)
Setting of the date (month and day)
O
off
Make a function inactive
on
Make a function active
program #
Program number
program
Program mode
program, segment
Ongoing program and ongoing segment
repeat count
Repeat frequency setting mode
real (real time)
repeat
The hour
Repeat command mode
rest time #
Rest for remaining time
ramp level
Ramp level of Segment # (Desired set temperature)
repeat start
Repeat start segment setting mode
ramp time #
r. tim (real time)
Ramp time of Segment #
(Time required to reach the ramp level)
the hour
#
segment #
Segment number
#
soak time
step
Soak time of Segment # (Holding time of the ramp
level)
Not in Ramp Operation
temp
Temperature mode
time
Time mode
wait
wait #
Wait function (Keep the operation until the desired
temperature is achieved)
Wait function of Segment #
year
the Christian era
E
#
P
#
R
#
#
S
T
W
#
Y
35
Flowchart of Operational Procedures
Run “MENU”
Menu key
Program operation
Fixed temperature
operation
When you run the oven in a
programmed operation,
proceeds as follows.
Select the program number
by using either the Πkey or
the  key and then press the
ENTER key.
Displays set
temperatue
A feasible program
number will appear on
the main display.
Set to your desired
temperature by using either
the Œ key or the  key.
The operation start
time will appear on
the main display in
minute.
ENTER key.
Press the ENTER key
Set to your desired operation start
time by using either the Πkey or
the  key.
The operation start
time will appear on the
main display in hour
as of now.
ENTER key
Press the ENTER key
Auto start
Auto stop
The oven can start the fixed temperature
operation after a lapse of the fixed time.
The oven can stop the fixed
temperature operation after a lapse
of the fixed time.
Displays set
temperatue
Set to your desired temperature by using either the
Œ key or the  key and then press
the ENTER key.
Set to your desired temperature by
using either the Œ key or the  key
and then press the ENTER key.
Set to your desired operation start time by using
either the Œ key or the  key.
The operation start
time will appear on
the main display in
minute.
Displays set
temperatue
The operation start
time will appear on the
main display in hour
as of now.
The operation stop
time will appear on
the main display in
minute.
The operation stop
time will appear on the
main display in hour
as of now.
When switching the sub display screens during standby
condition, the remaining time and the hour as of now can appear.
Once started operation, the remaining time (= HOLD), the hour
as of now and the set temperature can be switched on the sub
display.
Set the fan motion to
ON or OFF.
Set the fan motion after
the operation stopped.
Set the fan motion to
ON or OFF.
ENTER key.
Press the ENTER key
Select the wait function
ENTER key.
Set the wait function to ON when you want to hold the fixed
operation for a time that you have set in advance.
Set the wait function to OFF when you want to run the oven
through the operation for a time that you have set in advance.
ENTER key.
36
Press the ENTER key
Press the ENTER key
Program “MODE”
MODE
Main display
See the programming flowchart.
Inputting and deliting
programs (ProG)
Programming
NOTE:If there are no programs, this will not appear.
▲ ▼
ENTER key
Deleting programs
ENTER key
Select the programs number
that you want delete.
*The number of existing programs
will appear on the sub display.
Œ  keys
ENTER key
ENTER key
In case of a period of time
Time/Hour switching
function
In case of the hour
Select the timer mode that you
want to run in hour mode or in a
period of time mode while
running each operation.
Œ  keys
ENTER key
Key lock setting/
releasing function
The key lock will disable you
from doing the key action.
ENTER key
The key action will get
active.
Select the key lock mode.
Œ  keys
ENTER key
The alarm will be sounded.
Alarm buzzer ON/OFF
function
ENTER key
The alarm will not be
sounded.
Set the alarm to be sounded or not if a
problem occurs.
Display
Accumulating time (Accm)
The total time for the power being on can be
shown on the sub display.
Diplay the total time for the
power being on.
It will appear on the sub display.
ENTER key
Date and current hour
setting function (cLoK)
ENTER key
Set the Christian era
by using either theŒ
key or the key.
Set the date and hour.
ENTER key
Calibration off set
function (cAL)
ENTER key
The calibration off set
value that has been set in
advance will appear.
37
Set the hour by using
either theΠkey or
the  key.
Set the date by using
either theΠkey or
the  key.
▲ ▼
Display
ENTER key
ENTER key
Change to your off set value
by using either theΠkey or
the  key.
Flowchart for programming
Segment configuration
: Segments are made up of the
following items, and must be input
in this order.
MODE key
Press
▲ ▼ Key
Call up the program mode.
Temperature
ENTER
Ramp level
key
▲ ▼ Key
Time
Ramp time
Soak time
Call up the program number that you want to
input or edit.
ENTER
key
▲ ▼ Key
ENTER
key
Ramp time
▲ ▼ Key
Rising time
Input Ramp time.
Note: When you run this unit with full power,
input
.
ENTER
Ramp level
key
Target
temperature
When you want to rewrite programs, call up
your desired segment number on the main
display.
Note that this will appear in case of editing.
▲ ▼ Key
Input Ramp level.
Soak time
Time held at ramp
level
ENTER
key
▲ ▼ Key
Wait function Selects
whether
to give priority to
soak time (OFF),
or to hold process
time at ramp level
(ON).
ENTER
key
▲ ▼ Key
Input Soak time.
Note: If there is no soak time (changing
immediately to next temperature), input
0. To hold, select
Select wait function.
ENTER
key
▲ ▼ Key
ENTER
key
▲ ▼ Key
The next segment will appear.
Note: To repeat, press either the key or the
, and select it with
key to display
the ENTER key. Input the segment
number that you want to repeat, and
then do the repeat count.
* Input all the settings in the same way.
When
finished inputting all items, select
for the ramp time, and press the
ENTER key.
ENTER
key
▲ ▼ Key
Settings
finished
38

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project