USER MANUAL
Garden Shredder
IMPORTANT:
It is vital that you retain and thoroughly read and understand these safety and operating instructions. Incorrect use will make this machine inoperable.
MODEL NO. AS200100
6096-200120
GENERAL SAFETY RULES
GB
Meaning of symbols marked on the product
Read the user manual before using the machine
Wear safety goggles to protect your eyes
Wear ear protection to protect against noise
Wear dust mask to protect against dust
Wear gloves to protect your hands
Wear safety boots to protect against electric shock
WARNING!
When using electric tools, basic safety precautions, including the following, should always be followed to reduce the risk of fire, electric shock and personal injury.
Read all these instructions before operating this product and save these instructions.
• Keep work area clean
Cluttered areas and benches invite injuries.
• Consider work area environment
Do not expose power tools to rain. Do not use power tools in damp or wet locations. Keep work area well lit.
Do not use power tools where there is risk to cause fire or explosion.
• Guard against electric shock
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges or refrigerators).
• Keep children away
Do not let visitors touch the tool or extension cord. All visitors should be kept away form area.
• Store idle tools
When not in use, tools should be stored in a dry, high or locked up place, out of reach of children.
• Do not force the tool
It will do the job better and safer at the rate for which it was intended.
• Use the right tool
Do not force small tools or attachments to do the job of a heavy duty tool. Do not use tools for purposes not intended; for example, do not use circular saws to cut tree limbs or logs.
• Dress properly
Do not wear loose clothing or jewellery, they can be caught in moving parts. Rubber gloves and non-skid footwear are recommended when working outdoors.
Wear protective hair covering to contain long hair.
• Use safety glasses
Also use face or dust mask if the cutting operation is dusty.
• Do not abuse the cord
Never carry the tool by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.
• Do not overreach
Keep proper footing and balance at all times.
• Maintain tools with care
Keep cutting tools sharp and clean for better and safer performance. Follow instructions for lubrication and changing accessories. Inspect tool cord periodically and if damaged have it repaired by an authorized service facility. Inspect extension cords periodically and replace, if damaged. Keep handles dry, clean and free from oil and grease.
• Disconnect tools
When not in use, before servicing and when changing accessories such as blades, bits and cutters.
• Remove adjusting keys and wrenches
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.
• Avoid unintentional starting
Do not carry a plugged-in tool with a finger on the switch. Ensure switch is off when plugging in.
• Use outdoor extension cords
When tool is used outdoors, use only extension cords intended for outdoor use.
• Stay alert
Watch what you are doing. Use common sense. Do not operate tool when you are tired.
• Check damaged parts
Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated in this instruction manual.
Have defective switches replaced by an authorized service facility. Do not use the tool if the switch does not turn it on and off.
• WARNING!
The use of any accessory or attachment, other than those recommended in this instruction manual, may present a risk of personal injury.
• Have your tool repaired by a qualified person
This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using original replacement parts, otherwise this may result in considerable danger to the user.
• WARNING!
This tool must not be used by anyone under 16 years of age.
You have a responsibility of safety to others when you are operating this tool.
1
GB
• SAFETY INSTRUCTIONS FOR GARDEN SHREDDER
Read owners manual thoroughly to fully understand controls.
1. Prior to inspecting any part of this machine switch off the power supply, disconnect lead, and make sure all moving parts are completely stopped.
2. Keep children and people unfamiliar with this equipment away from the machine when in operation.
3. Do not allow hands or any other part of the body, or clothing inside the feeding chambers or discharge chute, or near any moving parts.
4. Wear safety glasses at all times while machine is in operation.
5. Wear gloves and avoid wearing loose clothing while operating the machine.
6. Before starting the machine, ensure that all screws and other fasteners are properly secured.
7. Machine should be operated on firm level surfaces only.
8. Before starting the machine, check that the cutting chamber is empty.
SPECIFIC SAFETY RULES
9. Extreme caution should be taken to ensure shreddable material does not contain metal, rocks, bottles, cans or other foreign objects.
10. Motor should be kept clean of debris and other accumulations.
11. Keep all guards and deflections in good working condition.
12. Stand clear of discharge chute at all times.
13. Do not over reach and keep face and body back from the feed opening.
14. If machine should become clogged; switch off the motor, disconnect the power lead, make sure all moving parts are completely stopped before cleaning clogged debris.
15. Never pull the machine by the power cord and keep cord away from water or sharp edges.
16. Disconnect the power cord when the machine is not in use.
17. Ensure the power cord is always in good condition. A cord with broken insulation is hazardous.
GENERAL IDENTIFICATION
1
2
3
4
11
9
8
5
10
7
6
1. Top Hopper
2. Top Hopper Safety Screws
3. ON/OFF Switch
4. Overload Protection Switc
5. Top Hopper Knob
6. Discharge Chute
7. Leg (R)
8. Leg (L)
9. Wheel (R)
10. Wheel (L)
11. Wheel Covers
2
GB
SPECIFICATIONS
Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2200 Watt
No Load Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3300 RPM
Hopper Size . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .394x270x200mm
Branch Capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40mm
Net Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39 Kg
•
•
•
•
•
•
•
•
•
•
PRECAUTIONS FOR USING SHREDDER
WARNING: Extreme caution should be taken to ensure shreddable material does not contain metal, rocks, bottles. Cans or other foreign objects.
CAUTION: Do not allow hands or any other part of the body, or clothing to enter inside the feeding chambers or discharge chute, while machine is operating.
Wear gloves while operating the machine.
Before starting the machine, ensure that all screws and other fasteners are properly secured.
Machine should be operated on firm level surfaces only.
Before starting the machine, check that the cutting chamber is empty.
Motor should be kept clean of debris and other accumulations.
Keep all guards and deflections in good working condition.
Stand clear of discharge chute at all times.
Do not over reach and keep face and body back from the feed opening.
Never pull the machine by the power cord and keep cord away from water or sharp edges.
Disconnect the power cord when the machine is not in use.
WARNING: If machine should become clogged, switch off the motor, disconnect the power cord, make sure all moving parts are completely stopped before cleaning clogged debris.
WARNING: Ensure the power cord is always in good condition. A cord with broken insulation is extremely dangerous and can result in fire, electric shock or serious personal injury.
WARNING: The operation of any tools can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before operating power tool, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend wide Vision Safety Mask for use over eyeglasses or standard safety glasses with side shields.
ASSEMBLY
• HOW TO ASSEMBLE YOUR SHREDDER
1. Push the large diameter section of the axle into the axle tube and secure the axle into position using the
M8 x 40 hex screws and star washer. (2 per side)
2. Push the wheel and then the 12mm flat washer over the axle.
3. Push the split pin through the hole in the end of the axle and bend the ends over using pliers.
4. Fix on wheel covers.
Fig. 1
• HOPPER (FIG.2)
Place the hopper on top of the feed tube and align the fixing holes. Secure with the safety set screws.
•
•
•
Fig. 2
OPERATION
CAUTION: Read and understand the safety instructions in this owners manual before using your shredder. Failure to comply can result in accidents involving fire, electric shock, or serious personal injury.
Connect the shredder to a suitable power outlet.
To start and stop the shredder, depress the switch located at the rear of the Motor.
To stop the shredder, switch to the off position. (Fig
3)
3
ON-Off
Switch
Overload protection switch
Fig. 3
• OVERLOAD PROTECTION AND MOTOR
JAMMING Your shredder comes with Overload
Protection which is activated when wood particles jam the blades or when material is fed into the hopper too fast. If required follow the unjamming procedure noted below and then press the reset button. (Fig. 3)
• FEEDING LEAVES AND SMALL GARDEN CLIP-
PINGS - TOP HOPPER
The sloping chute of the top hopper is designed to accept leaves and small garden clippings.
Shredding and mulching is achieved by natural suction of the debris through the blade chamber. Do not overfeed and do not feed wet, soggy material into the garden shredder as this may clog the blade chamber and the discharge chute. (Fig. 4)
GB
• SIDE CHUTE
The elongated chute located at the rear of the machine is specially designed to accept solid garden clippings and branches up to 40mm in diameter.
IMPORTANT: When feeding long, large diameter material, control the rate of feed by pulling back on the material so as not to stall or overload the motor. (Fig. 6)
WARNING!
Do not under any circumstances, place hands inside the feeding chutes while the machine is operation. Force feeding of debris is not necessary due to the natural suction action of the blades.
Fig. 6
• ATTACHING MULCH BAG
Place a heavy duty trash bag using the mulch bag strap.
(Fig 7)
GB
• DISASSEMBLY
1. Loosen caging knobs and remove the top cover assembly.
2. Rotate the cutter base anti clockwise and place a piece of wood between the cutter base and cutting chamber wall so as to stop the cutting base retating.
(Fig. 8)
3. Remove the center hold down bolt by turning it anti clockwise using a 17mm spanner.
4. Remove the square washer, square bush, V-cutter to expose cutter base.
Fig. 10
• CLEANING
After use, always wipe clean the outside of the unit to remove any build up of material with a damp cloth. Clean the inside of the cutting chamber and remove any left over material, Do not hose down with water.
Fig. 8
• SHREDDING BLADES MAINTENANCE
To inspect or renew the double sided shredding blades there is no need to remove the cutter base. To remove simply undo the counter sunk screws with the 6mm hex wrench supplied with the machine and turn them through
180 degrees. These blades are double ground and can be used on both sides. When blunt on both sides renew and ensure they are screwed in tightly.
ASSEMBLY This is carried out in the reverse sequence to that of disassembly but with careful inspection of all components. Ensure that cutter base is assembled with the scraping plates facing down towards the motor and that the spring washer is situated under the head of the centre hold down bolt. (Fig. 9)
Fig. 4
• FEEDING TWIGS AND SMALL BRANCHES - TOP
HOPPER
The top hopper also accepts medium to larger size garden clippings.
Shredding and mulching is achieved through the same action as leaves and small clippings. If a finer type mulch is required than is initially achieved, re-feed the mulch through again until the desired result is obtained. (Fig 5).
Fig. 5
4
Fig. 7
MAINTENANCE
Your Shredder has been designed for a low level of maintenance, involving routine cleaning and inspection. The motor of the Shredder is maintenance free and requires no attention. For the best results the blades must be kept sharp at all times. The blades have dramatically less cutting power when blunt.
The Shredder will tear rather than cut when the blades are blunt. When this occurs rotate the double sided blades or replace the blades immediately.
IMPORTANT: Before attempting any maintenance switch the machine off and disconnect the power cord.
• V-CUTTER MAINTENANCE
• Switch the machine off and disconnect the power cord ensuring all moving parts are completely stopped.
• Wear gloves when attempting any maintenance to the cutting blades.
Fig. 9
Before replacing the top cover assembly ensure that the
V-cutter is positioned as shown in (Fig.10) Replace the top cover assembly and secure tightly the caging knobs.
If caging Knobs are not tight the motor will not start due to the motor lock out switch not being activated.
5
