Martin Yale 1501 CV-7 Installation, Maintenance & Operating Instructions
The Martin Yale 1501 CV-7 is a versatile and efficient machine designed to handle all your paper folding needs. With its ability to execute various folds, including letter, Z, single, double parallel, French, Baronial, and custom folds, you'll expand your paper handling capabilities. Its user-friendly setup and adjustable paper guides ensure precise and consistent folding. The retarder roller can be adjusted to accommodate different paper weights, providing optimal feeding performance.
PDF
Download
Document
Advertisement
Advertisement
Installation, Maintenance, & Operating instructions Model 1501 Specifications | Table of Contents Ft Parts List & Diagram see Page 29,30 ; nstallation .….….….….…..…..….erenersenenencennbnn age Feed eat NS KA 2.0 бе шр ..….………erverrenrerrenrenrenerrrernrarererersrente Раде 2 Sheet gaBacity....... ! % 2.1 Paper Guides... Page 2 Types@f Fo « Letter, à ER Z, C ur 2.2 Paper Guide Rollers. Page 2 re 2.3 Feed Adjustment.............. ene Page 2, 3 Feeding M | ] 3.0 Fold Settings 8: Operation ....:..........—... Page 3 Lightest Panta “ED y ete,» Mila] Letter Fold Setup... errr: Page 3 Heaviest Pg: ne Ra | Зо Rasa ID coors nene Lesssresannanee Page 3, 4 Max. Paper Ste. Я NS 4 sE 3 SN Ras in sep ecercruenoneneno Page 4 Min. Paper Sized, 4 oy Fold Setup. м Ena Morenas Page 4,5 Max. Fold Length *s %, Ei “ay, la A pb for Stapled Sets....... Beene rot i > PTE рати E H de feeb eevoivnnrne ; First Fold. ........ ELL tata RES o A О ний N ce ecs res Page 5, 6 Second Fold ........ | pps E ne Bmw Page 6 т TI fr neggblrocanaros ge Min. Fold Length | A page 6 FirstFold........... Е QUE, anne Page 6 Second Fold ........ 4.3 ВБалй Si 0 Ennio A... Page 6 Fold Stapled Sets ..... 5.0 Taie qu peererueceorenocenean rele dleneraoecores Page 6 Electrical Specifications 5.1 Pame Pe a Feed........... ni Page 6,7 5.21 STEERING eee Nene... 27 Ae 7 | UL CSA Approved ..... | a 5.3 С EE enn. EF page 7 ; Dimensions. ......... Na «page Ele, ERE page 7.8 AM N 7, reee gf En... iz crecrreces rage 8 | arzt | Shipping Weight... nf menaces Boge ae 6 Whi ded Paper-.. AT LS eii PAGE Bi | einige HA]: | *11" Sheets Per Hour Re 5 7P et (Exits on то) of Fold | Table Page 8 и | BUT. ii : Bap ......Page Bw | «+ cee [Bl | French Translation. Mu AGE, I trations A ee y TD Page 26-28 Hl Spanish Translation ................. jun fens Page 31 Introduction Thank you for selecting the Martin Yale Model 1501 AutoFolder. The 1501 can execute letter, Z, single, double parallel, French, Baronial, and custom folds within its paper size capacity. Thorough understanding of this information will help eliminate most operator-associated errors and ensure years of trouble-free performance. WARNING: Never connect power to the machine until you are ready to set up and operate the 1501. The AC outlet must be nearby and not blocked. This machine contains moving parts. During setup, operation, and maintenance keep hands, hair, loose clothing, and jewelry away from all moving parts. Serious bodily injury could result. Service, or disassembly of side covers should only be attempted with the power discon- nected and locked out. 1.0 Installation Carefully unpack the 1501. Note the feed table (Item 1) and the 2nd fold table (Item 34) are packed separately within the box, and will be installed later. Carefully inspect carton contents for damage. Report any shipping damage to the carrier and your Martin Yale Dealer. Place the folder on a flat, level work surface. Connect power to the machine. Turn on the machine and let it run for a few minutes. During this process you may hear a thumping sound caused by flat areas on the rubber folding rollers. These flat areas occur during long periods of non-use and will be eliminated during this initial run. If your folder is inactive for long periods, you should repeat this process before attempting to fold paper. NOTE: Failure to do so may cause folding problems. NOTE: Never handle the feed table by the paper guides. Install the feed table onto the 1501. To do so, lower the retarder roller (Item 4) by loosening the thumb nut (See Figure 3.) under the feed table until the retarder roller is level with the top of the feed table. Slide the left and right paper guide rollers (Item 14) on the feed roller shaft until they are next to the feed roller. Install the feed table by placing the front slots of the feed table onto the locating pins near the folding rollers (See Figure 1.), and lower onto positioning pins. Install the 2nd fold table (Item 34). To do so, install the fold table over the two tie rods (Item 31) located just below the feed table. (See Figure 2.) The 2nd fold table can be installed in two ways; with the open (folding) end, or the closed (deflector) end toward the folding rollers, as needed for the fold being made. ...2.0. Setup 2.1 Paper Guides Adjust the feed table paper guides (Items 2 & 5) so the sheet is centered over the feed roller (Item 12) and p paper slides freely down between the guides without excessive side play. To adjust, grip the guides at the top and bot- tom where they are held in place on the cross shaft and slide into position. NOTE: Improper setting of the feed table paper guides may cause inconsistent folding or crooked folds. | 2.2 Paper Guide Rollers The paper guide rollers (Item 14) should be positioned approximately 1/4" to 1/2" from the left and right edge of the paper. Always slide the left and right paper guide rollers on the feed roller shaft until they are next to the feed roller before installing or removing the feed table. | 2.3 Feed Adjustment The retarder roller (Item 4) can be set in two ways, with power off, and power on. For power-off setting, place one sheet of paper between the feed roller and the retarder roller. Hold the sheet by the tail end and, while mov- ing the paper in and out between the retarder and feed roller, raise the retarder roller until you feel a slight pull on the paper. The retarder roller is raised and lowered via the thumb nut under the feed table (See Figure 3). Hold the paper and, rotate the hand wheel (Item 21), for one complete revolution of the feed roller. You should | feel an even pull through the entire revolution of the feed roller. If at any point you do not feel an even pull, readjust the retarder roller. For power-on setting, place one sheet of paper between the feed roller and the retarder roller. Hold the sheet by the tail end and turn on the machine. Adjust the retarder roller until you feel a consistent pull on the paper. Turn power off and remove the paper. To test for correct setting of the retarder roller, connect the machine to an electrical outlet. Place three sheets of (2) the paper to be folded onto the feed table Turn on the folder. Single sheets should be forwarded into the - machine. If they are not, readjust the retarder roller. Through normal use, the retarder roller will develop a flat wear area. When worn to the point that it will no longer contact the feed roller, loosen the nut on the retarder locking screw. Rotate in the proper direction (See Figure 3) to expose a new surface and lock into position. NOTE: The retarder roller should always be locked in a stationary position. 3.0 Fold Settings & Operation | The 1501 can be set up to make all standard folds including; letter, double parallel, Z, and single. The fold chart on the receiving tray (See Figure 11.) illustrates the standard fold table paper stop settings for making the various types of folds (inch and metric paper sizes). 1st refers to the letter setting on the 1st fold table scales (Item 17). 2nd refers to the letter setting of the 2nd fold table scales (Item 35). The following instructions assume a standard 8-1/2" x 11" sheet is being folded. Non-standard sizes should be measured and paper stops - set according to measurements. 3.1 Letter Fold Setup (See Figure 4.) 1. Loosen the paper stop locking knobs on thelst fold table (Item 16) and move the paper stop (Item 15) to the center of the letter A circle. Retighten the locking knobs. 2. Place the 2nd fold table (Item 34) into position with the open (folding) end toward the folding rollers. Loosen the paper stop locking knobs on the 2nd fold table and move the paper stop (Item 15) to the center of the letter S circle. Retighten the locking knobs. 3. Place a sheet on the feed table and set the paper guides so the sheet is centered over the feed roller and slides freely down between the guides without excessive side play. To aid paper feeding, slide the paper guide rollers on the feed roller shaft until they are 1/4" to 1/2" from the left and right edge of the paper to be folded. | 4. Set the retarder roller as described in the section on feed adjustment. 5. Jog the paper to be folded on a Martin Yale Model 400 or 4200 Jogger for at least one minute, or hand jog. (Jogging dissipates static electricity and fluffs the paper.) 6. Take a stack of jogged paper and fan the paper out as indicated in Figure 9, 7. Place the fanned paper onto the feed table (See Figure 8.) with the top sheet positioned where the feed roller and retarder meet. | 8. Manually feed one sheet through the machine and position the receiving tray (Item 19) so the folded sheet exits properly onto the tray. 9. Turn on the folder and fold several sheets. Stop the folder and inspect the folded sheets for accuracy. 10. Make 1st fold correction with the 1st fold table paper stop. Make 2nd fold correction with the 2nd fold table paper stop. (See Figure 4 for first and second fold descriptions.) 11. After corrections are made, turn on the folder and complete the folding job. 3.2 Z Fold Setup (See Figure 5.) 1. Loosen the paper stop locking knobs on the 1st fold table (Item 16) and move the paper stop (Item 15) to the center of the letter B circle. Retighten the locking knobs. 2. Place the 2nd fold table (Item 34) into position with the open (folding) end toward the folding rollers. Loosen the paper stop locking knobs on the 2nd fold table and move the paper stop (Item 15) to the center of the letter S circle. Retighten the locking knobs. 3. Set the paper guides so a sheet is centered over the feed roller and slides freely down between the guides (3) 9. 10. a 11. without excessive side play. To aid paper feeding, slide the paper guide rollers on the feed roller shaft until - they are 1/4" to 1/2" from the left and right edge of thé paper to be folded. Set the retarder roller as described in the section on feed adjustment. Jog the paper to be folded on a Martin Yale Model 400 or 4200 Jogger for at least one minute, or hand jog. (Jogging dissipates static electricity and fluffs the paper.) Take a stack of jogged paper and fan the | paper out as indicated in Figure 9. Place the fanned paper onto the feed table (See Figure 8.) with the top sheet positioned where the feed roller and retarder meet. Manually feed one sheet through the machine and position the receiving tray so the folded sheet exits prop- erly onto the tray. Turn on the folder and fold several sheets. Stop the folder and inspect the folded sheets for accuracy. Make 1st fold correction with the 1st fold table paper stop. Make 2nd fold correction with the 2nd fold table paper stop. (See Figure 5 for first and second fold descriptions.) After corrections are made, turn on the folder and complete the folding job. 3.3 Setup for Double Parallel Fold (See Figure 7.) 1. 9. 10. 11. Loosen the paper stop locking knobs on the 1st fold table (Item 16) and move the paper stop (Item 15) to the center of the letter C circle. Retighten the locking knobs. Place the 2nd fold table (Item 34) into position with the open (folding) end toward the folding rollers. Loosen the paper stop locking knobs on the 2nd fold table and move the paper stop (Item 15) to the center of the letter U circle. Retighten the locking knobs. Set the paper guides so a sheet 1s centered over the feed roller and slides freely down between the guides without excessive side play. To aid paper feeding, slide the paper guide rollers on the feed roller shaft until they are 1/4" to 1/2" from the left and right edge of the paper to be folded. Set the retarder roller as described in the section on feed adjustment. Jog the paper to be folded on a Martin Yale Model 400 Jogger for at least one minute, or hand jog. (Jogging dissipates static electricity and fluffs the paper.) Take a stack of jogged paper and fan the paper out as indicated in Figure 9. Place the fanned paper onto the feed table (See Figure 8.) with the top sheet positioned where the feed roller and retarder meet. В Manually feed one sheet through the machine and position the receiving tray so the sheet exits properly onto the tray. Turn on the folder and fold several sheets. Stop the folder and inspect the folded sheets for accuracy. Make 1st fold correction with the 1st fold table paper stop. Make 2nd fold correction with the 2nd fold table paper stop. (See Figure 7 for first and second fold descriptions.) After corrections are made, turn on the folder and complete the folding job. 3.4 Single Fold Setup (See Figure 6.) 1. Loosen the paper stop locking knobs on the 1st fold table (Item 16) and move the paper stop to the center of the letter C circle. Retighten the locking knobs. Place the 2nd fold table (Item 34) into position with the closed (deflecting) end toward the folding rollers. Set the paper guides so a sheet is centered over the feed roller and slides freely down between the guides without excessive side play. To aid paper feeding, slide the paper guide rollers on the feed roller shaft until they are 1/4" to 1/2" from the left and right edge of the paper to be folded. (4) 9. 10. 11. Set the retarder roller as described in the section on feed adjustment. | Jog the paper to be folded on a Martin Yale Model 400 J ogger for at least one minute, or hand jog. (Jogging dissipates static electricity and fluffs the paper.) Take a stack of jogged paper and fan the paper out as indicated in Figure 9. Place the fanned paper onto the feed table (See Figure.8.) with the top sheet positioned where the feed roller and retarder meet. | Manually feed one sheet through the machine and position the receiving tray so the sheet exits properly onto the tray. Turn on the folder and fold several sheets. Stop the folder and inspect the folded sheets for accuracy. Make first fold correction with the 1st fold table paper stop. (See Figure 6.) After corrections are made, turn on the folder and complete the folding job. 3.5 Setup for Stapled Sets We do not recommend folding stapled sets as it shortens the life of the folding rollers. If you choose to fold sta- pled sets with the 1501, we suggest the following procedure. 2. 3. 4. Adjust the retarder to the thickness of the stapled set. NOTE: Do not atiempt to fold more than three stapled sheets of 20# stock at one time. Use two staples, one on each side of the paper, parallel to the top edge. Proceed with the folding job. If this procedure is not successful, raise the retarder to maximum opening and hand-feed individual sets. 3.6 French Fold Setup Please follow these instructions for setup of the French fold. The paper stop settings for this fold are not listed on the simplified fold chart. 4. 5. The French fold requires running the material through the folder in two steps. For step one, set the folder up as described in the single fold setup (See Section 3.4.) for the size paper to be folded. Run the entire folding job through the 1501. For step two, set the folder up as described in the single fold setup (See Section 3.4.) to the size you intend to refold. When setting the paper guides, position the guides so the folded edge of the sheet is closer to the feed roller. This helps prevent skewing of the folded paper. det the retarder (slip fit) for double thickness of the material to be folded. Run the entire folding job through the 1501. 3.7 Baronial Fold Setup Please follow these instructions for setup of the Baronial fold. The paper stop settings for this fold are not list- ed on the simplified fold chart. 2 The Baronial fold requires running the material through the folder in two steps. For step one, set the folder up as described in the single fold setup (See Section 3.4.) for the size paper to be folded. Run the the entire folding job through the 1501. For step two, set the folder up as described in the letter fold setup (See Section 3.1.) to the size you intend to refold. When setting the paper guides, position the guides so the folded edge of the sheet is closer to the (5) feed roller. This helps prevent skewing of the folded paper. 4. Set the retarder (slip fit) for double thickness of the material to be folded. 5. Run the entire folding job through the 1501. 4.0 Maintenance 4.1 Feed Roller | After a period of normal operation, the feed roller will become coated by ink, toner, lint, and other contami- nants. Clean the feed roller by wiping with a damp cloth containing a mild soap and water solution. NOTE: Do not use rubber roller cleaner or other solvents on the feed roller. To maximize the gripping power of the feed roller and to remove any remaining contaminants, go over the feed roller surface with medi- um grit emery cloth. Replace the feed roller when grooves on the feeding surface are no longer visible (feed roller appears smooth). 4.2 Folding Rollers During normal operation, the folding rollers will become coated with ink, toner, lint, and various other conta- minants. Contaminated folding rollers can cause a variety of feeding problems. We recommend cleaning the folding rollers after every folding job, according to the following procedure. Regular cleaning will ensure opti- mum performance and add years of life to the folding rollers. 1. Make sure power has been disconnected and locked out. 2. Remove the feed table, 2nd fold table, and receiving tray. | 3. Liberally spray Martin Yale Rubber Roller Cleaner and Rejuvenator onto a clean, dry cloth. Roller Cleaner and Rejuvenator has been specifically formulated for use in cleanirig the folding rollers. Use of any other cleaner may deteriorate the rollers and void machine warranty. | 4. Briskly clean each roller until no more contaminates appear on the cloth surface. Rotate the rollers via the handwheel and continue to clean until all roller surfaces are smooth and resilient, not hard or glazed. >. If necessary, remove any glaze with a non-abrasive cleaning pad, such as a 3M Scotchbrite pad. 6. After cleaning, turn on the machine and let it run a few minutes to evaporate any cleaner left on the folding rollers. 4.3 Bearings After each 8 hours of machine operation, thoroughly clean the folding rollers and remove any contaminates from the ends of the rollers and bearings. (See Figure 10.) Lubricate all bearings and shafts with one drop of light machine oil on each. CAUTION: Do not allow any oil to come incontact with the folding rollers. If oil is spilled on the felding rollers, remove immediately with Martin Yale Rubber Roller Cleaner and Rejuvenator. 9.0 Troubleshooting 5.1 Paper Will Not Feed Possible Cause Solution Feed table not properly seated. Make sure the feed table is mounted correctly on the | locating pins. Paper guides too tight (paper buckles). Adjust the paper guides so a sheet slides freely down | | between the guides without excessive side play. (6) Improper fanning of paper. Worn out feed roller. Feed roller contaminated. Retarder set too tight. Flat area on retarder. Static electricity buildup. Loose motor belt. 5.2 Improper Stacking Possible Cause Receiving tray improperly set. Static buildup. 5.5 Crooked Folds — Possible Cause | Excessive side play between paper guides and paper edges. Fold table paper stops improperly set or not locked in position. Paper not square. Contaminated folding rollers. 5.4 Ink Smudges on Paper Possible Cause Ink not dry. Grasp a stack of paper and place it on its long side on a flat, level surface. Even the paper and grip it tightly with your left hand. Loosely grip the paper with your right hand . and pull the paper to you until it forms a semi-circle. Now tightly grip and hold the right side as you relax your left hand grip. (See Figure 9 for diagram of properly fanned paper.) Replace the roller. See instructions in feed roller section. Readjust the retarder. Reset according to instructions in feed adjustment section. Jog paper. Spray Martin Yale Static Eliminator liberally over paper edges, feed table, fold tables, and receiving tray. Adjust or replace motor belt. Solution Reset the receiving tray to slightly longer than the folded paper. | Jog paper. Ensure that anti-static tinsel strip is installed. Spray Martin Yale Static Eliminator liberally over paper edges, feed table, fold tables, and receiving tray. Solution Readjust the paper guides to eliminate excessive side play. Readjust the paper stops and lock in position. Recut paper until square. (Or adjust fold table paper stops.) Clean according to instructions in maintenance section. Solution Allow additional ink drying time before folding. Some (7) Excessive toner on photocopied stock. 5.5 Jams Possible Cause More than a single sheet feeding into the — folder. Folded sheets backing onto the folder. 5.6 Wrinkled Paper Possible Cause Feed table paper guides misaligned. Feed table paper guides too tight. Folding roller springs worn. Contaminated folding rollers. Worn folding rollers. 5.7 Paper Exits on Top of Fold Table — Possible Cause Contaminated folding rollers. Static buildup. Jog paper. 5.8 Folds More Than a Single Sheet Possible Cause Improper gap between retarder and feed roller. inks do not dry, they only set (dry to the touch). Because of the physical nature of friction feeding, you may notice a mark on the leading edge of the paper. Check copy machine. Solution | Readjust the retarder according to instructions in the feed adjustment section. | Reset the receiving tray to slightly longer than the folded paper. Solution Align paper guides perpendicular to the folding rollers until paper feeds straight into the folder. Set guides so a sheet slides freely down between the guides without excessive side play. Replace with new springs. Clean according to instructions in maintenance section. Folding rollers should be replaced when gaps appear between the rollers. Solution Clean according to instructions in maintenance section. Spray Martin Yale Static Eliminator liberally over paper edges, feed table, fold tables, and receiving tray. Solution Readjust the retarder according to instructions in the feed adjustments section. Introduction Nous vous remercions d’avoir choisi le Martin Yale Model 1501 Auto Plieur. Le 1501 peut exécuter les plages lettre, Z, unique, double parallèle, français, Baronial, et les pliages sur mesure dans sa capacité de taille de la feuille. (8) REFERENCE ILLUSTRATIONS Fig. 1 - Feed Table Installation Insert Deflector End For Single Fold Tie N ju > insert Open End For Double Fold Fig. 2 - Fold Table Installation Fig. 3 - Feed Adjustment Retarder Locking Screw € Nut Pivot Belt Retarder Roller Fig. 4 - Tri-Fold Thumb Nut <a——— 2nd Fold —— —> «———— 1st Fold (26) REFERENCE ILLUSTRATIONS (con’t) Fig. 5 - Z-Fold 2nd Fold Fig. 6 - Single Fold 2nd Fold 1st Fold Fig. 7 - Double Parallel (27) REFERENCE ILLUSTRATIONS (con't) Paper Guide Fanned Paper Feed Roller Feed Table Thumb Nut. Fig. 8 - an capes: Retarder Roller Oil Here Fig. 10 - Lubricate all roller bearings Metal Shaft - Bushing Top Front Fig. 9 - Side View of Fanned Paper SIMPLIFIED FOLDING CHART TYPE OF PAPER SIZE FOLD 8 41/2X11 81/2X 14 *11X17 A4 FAS 1 \ st «< на zB __—Indi st A à 1 > st Kal REVERSE SECOND FOLD TABLE | e a oR crconD POLO TaeLE bETIINS -—— * 1217A MODEL ONLY Fig. 11 - Folding Chart ОО 00 0 О (ЧО < LT Q|\S|@O Im mm ALI ALA | +|=|+|<lo|<lo (28) \ И 4 y y A Я / 7 À 4 nn bs a 5 5 A y ji pres E ê (29) tem No. Description ON OO UN A WN — NP NP ГО NN NN yoo E E oo _— А нА dk 5 О О) сл О WON OO NOU RON EIO Feed Table Left Paper Guide Paper Guide Support Shaft Retarder Roller/Arbor Right Paper Guide Nylon Bearing Qilite Bronze Bearing Feed Roller Shaft Main Drive Roller (Long Journal) Spring, Blue Feed Roller Arbor Feed Roller Rubber Left Side Main Frame Paper Guide Rollers Paper Stops 1st Fold Table Assembly 1st Fold Table Scale Fold Table index Pins Receiving Tray Cover, Operators Side Hand Wheel Capacitor for 115V Motor Capacitor for 220V Motor Motor Guard Pulley Flange — Pulley, 44T Part No. W-A003508 W-AO1501L W-0001541 WRA001516 W-A01501R M-0007509 M-S013010 W-0001540 WRA001530 M-S031035 М-О003125 M-0003548 W-0001598 M-0003030 W-0001534 W-A001519 М-О001567 M-0003104 W-0001596 W-0001504. M-5032009 M-5045101 M-S045102 W-0001586 M-5022022 M-5022019 ltem No. Description 27 Timing Belt, #150XL037 28 Motor Pulley, 15T 29 Right Side Main Frame 30 Motor, 115V, PSC Type 31 Tie Rods (2nd Fold Table) 32 Motor, 220V, PSC Type 33 Paper Chute 34 2nd Fold Table Assembly 35 2nd Fold Table Scale 36 Screen Guard 37 Intermediate Rollers 38 Nyliner Bearing 39 Roller Guard (220V Only) 40 Cover, Non-Operator's Side 41 Left Side Bracket (220V Only) 42 On/Off Switch Not Shown Taper Index Pin Anti-Static Tinsel Assembly Gear, 24T, Plastic Right Side Bracket (220V Only) Pulley, Plastic, 2 3/8 Dia. Pulley, Steel, 7/8 Dia. (30) Rubber Belt, Round Fan, 10-Blade Paper Stop Bracket Part No. M-S025026 M-S022073 W-0001589 M-5021042 M-0001542 M-S021043 W-0001585 W-A001520 M-0001568 W-0001587 WRA001532 M-S014027 W-0001588 W-1001504 \\/-О0095280 M-5033045 M-0085242 W-A001509 M-0003033 W-O095265 M-O001591 М-О007507 M-5023001 M-5037361 W-O001507 Qty. wh wad wed =k PO ©) = PY NO ll_—o— dl CA wk ~ ON/OFF | MOTOR — SWITCH Les POWER CORD | ) J (BLUE) CAPACITOR — ) | | ap 7 = | | À GROUND | N | AC POWER GREEN ummm — 0 110V/120VAC (GREEN/YELLOW) (220VAC) NOTE: VALUES FOR 110V/120VAC (VALUES FOR 220VAC) MODEL 1501 WIRING DIAGRAM FOR 110V/120VAC (220VAC) (31) Martin Yale INDUSTRIES, INC. 251 Wedcor Avenue * Wabash, IN 46992 Phone (219) 563-0641 * Fax (219) 563-4575 MY 10/97 Technical Support (219) 563-0641 5027201 ">

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Handles a wide range of paper sizes and types
- Executes various fold types, including letter, Z, single, double parallel, French, Baronial, and custom folds
- Adjustable paper guides and feed rollers for precise paper handling
- Easy-to-use controls and intuitive operation
- Durable construction for long-lasting performance
Frequently asked questions
The 1501 CV-7 can execute various folds, including letter, Z, single, double parallel, French, Baronial, and custom folds.
The maximum paper size that the 1501 CV-7 can handle is 11" x 17".
To adjust the paper guides, grip the guides at the top and bottom where they are held in place on the cross shaft and slide into position.