Cisco AS5350XM, AS5400XM Installation Manual

Add to My manuals
104 Pages

advertisement

Cisco AS5350XM, AS5400XM Installation Manual | Manualzz

Cisco AS5350XM and

Cisco AS5400XM Universal Gateways

Card Installation Guide

Corporate Headquarters

Cisco Systems, Inc.

170 West Tasman Drive

San Jose, CA 95134-1706

USA http://www.cisco.com

800 553-NETS (6387)

Customer Order Number: DOC-7817406=

Text Part Number: 78-17406-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The following information is for FCC compliance of Class A devices: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio-frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case users will be required to correct the interference at their own expense.

The following information is for FCC compliance of Class B devices: The equipment described in this manual generates and may radiate radio-frequency energy. If it is not installed in accordance with Cisco’s installation instructions, it may cause interference with radio and television reception. This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in part 15 of the FCC rules. These specifications are designed to provide reasonable protection against such interference in a residential installation. However, there is no guarantee that interference will not occur in a particular installation.

Modifying the equipment without Cisco’s written authorization may result in the equipment no longer complying with FCC requirements for Class A or Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.

You can determine whether your equipment is causing interference by turning it off. If the interference stops, it was probably caused by the Cisco equipment or one of its peripheral devices. If the equipment causes interference to radio or television reception, try to correct the interference by using one or more of the following measures:

• Turn the television or radio antenna until the interference stops.

• Move the equipment to one side or the other of the television or radio.

• Move the equipment farther away from the television or radio.

• Plug the equipment into an outlet that is on a different circuit from the television or radio. (That is, make certain the equipment and the television or radio are on circuits controlled by different circuit breakers or fuses.)

Modifications to this product not authorized by Cisco Systems, Inc. could void the FCC approval and negate your authority to operate the product.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCSP, CCVP, the Cisco Square Bridge logo, Follow Me Browsing, and StackWise are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn, and iQuick Study are service marks of Cisco Systems, Inc.; and Access Registrar, Aironet, BPX, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, Cisco, the Cisco Certified

Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Enterprise/Solver, EtherChannel, EtherFast,

EtherSwitch, Fast Step, FormShare, GigaDrive, GigaStack, HomeLink, Internet Quotient, IOS, IP/TV, iQ Expertise, the iQ logo, iQ Net Readiness Scorecard, LightStream,

Linksys, MeetingPlace, MGX, the Networkers logo, Networking Academy, Network Registrar,

Packet

, PIX, Post-Routing, Pre-Routing, ProConnect, RateMUX, ScriptShare,

SlideCast, SMARTnet, The Fastest Way to Increase Your Internet Quotient, and TransPath are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or Website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0601R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

© 2006 Cisco Systems, Inc. All rights reserved.

C H A P T E R

1

C H A P T E R

2

Preface

vii

Document Organization

vii

Document Conventions

viii

Obtaining Documentation

xiv

Cisco.com

xiv

Product Documentation DVD

xiv

Ordering Documentation

xiv

Documentation Feedback

xiv

Cisco Product Security Overview

xv

Reporting Security Problems in Cisco Products

xv

Obtaining Technical Assistance

xvi

Cisco Technical Support & Documentation Website

xvi

Submitting a Service Request

xvii

Definitions of Service Request Severity

xvii

Obtaining Additional Publications and Information

xviii

Safety Warnings, Recommendations, and Tools Required

1-1

General Safety

1-1

Maintaining Safety with Electricity

1-2

Preventing Electrostatic Discharge

1-3

Required Tools and Equipment

1-3

Where to Go Next

1-4

Feature Card and Carrier Card Guidelines

2-1

Overview

2-1

Online Insertion and Removal of Feature Cards

2-2

Removing and Installing Populated Carrier Cards

2-2

Removing a Populated Carrier Card

2-3

Installing a Populated Carrier Card

2-5

Getting Help

2-7

Where to Go Next

2-7

C O N T E N T S

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide iii

Contents

C H A P T E R

3

C H A P T E R

4

C H A P T E R

5

C H A P T E R

6

T1 and E1 Feature Cards

3-1

Overview

3-1

Online Installation and Removal of the T1 or E1 Feature Card

3-2

Removing the T1 or E1 Feature Card

3-3

Installing the T1 or E1 Feature Card

3-9

Configuring Input Impedance for the E1 Feature Card

3-11

Configuration

3-11

Verification

3-12

Getting Help

3-12

Where to Go Next

3-12

Channelized T3 Feature Card

4-1

Overview

4-1

Online Insertion and Removal of the CT3 Feature Card

4-2

Removing the CT3 Feature Card

4-2

Installing the CT3 Feature Card

4-5

Getting Help

4-7

Where to Go Next

4-7

Universal Port and Dial-Only Feature Cards

5-1

Overview

5-1

Restrictions for the Universal Port and Dial-Only Feature Cards

5-2

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

5-3

Removing the Universal Port or Dial-Only Feature Card

5-3

Installing the Universal Port or Dial-Only Feature Card

5-8

System Processing Engine Firmware

5-10

Getting Help

5-10

Where to Go Next

5-10

Voice Feature Card

6-1

Overview

6-1

Restrictions for the Voice Feature Card

6-2

Online Insertion and Removal of the Voice Feature Card

6-3

Removing the Voice Feature Card

6-3

Installing the Voice Feature Card

6-7

Replacing PVDM2 Modules in the Voice Feature Card

6-8

Orienting the PVDM2 Module During Installation

6-9

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide iv 78-17406-01

C H A P T E R

7

A P P E N D I X

A

Removing PVDM2 Modules From the Voice Feature Card

6-9

Installing PVDM2 Modules in the Voice Feature Card

6-10

Digital Signal Processor Firmware

6-11

Getting Help

6-11

Where to Go Next

6-11

Troubleshooting

7-1

LEDs

7-1

Mixing WAN Feature Cards

7-5

Mixing Universal Port and Dial-Only Feature Cards

7-6

Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards

7-6

Monitoring the Chassis Environment

7-7

Displaying Environment Status

7-8

Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards

7-10

Using Drop and Insert Mode on the CT3 Feature Card

7-10

Troubleshooting Network Interfaces

7-11

Getting Help

7-11

Cabling Specifications

A-1

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

A-1

8-Port T1 or E1 Feature Card Cable and Port Pinouts

A-6

Attaching the 8-Port T1 or E1 Feature Card Interface Cable to a Bracket (Optional)

A-8

CT3 Feature Card Cable and Port Pinouts

A-12

Bantam Jack Port Pinouts

A-13

Contents

I

N D E X

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide v

Contents vi

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

This preface describes the objectives and organization of this document and explains how to find additional information on related products and services. This preface contains the following sections:

Document Organization, page vii

Document Conventions, page viii

Obtaining Documentation, page xiv

Documentation Feedback, page xiv

Cisco Product Security Overview, page xv

Obtaining Technical Assistance, page xvi

Obtaining Additional Publications and Information, page xviii

Document Organization

This publication is designed for people who have some experience installing networking equipment such as routers, hubs, servers, and switches. The person who installs the server should be familiar with electronic circuitry and wiring practices and have experience as an electronic or electromechanical technician.

Table 1 describes the contents of each chapter in this document.

Table 1 Document Organization

Chapter

Chapter 1

Chapter 2

Chapter 3

Chapter 4

Chapter 5

Title

Safety Warnings,

Recommendations, and

Tools Required

Feature Card and Carrier

Card Guidelines

T1 and E1 Feature Cards

Channelized T3 Feature

Card

Universal Port and

Dial-Only Feature Cards

Description

Describes the safety warnings, recommendations, and the tools required to install dial feature cards in the chassis.

Describes the tasks you must perform to remove and install carrier cards.

Describes online insertion and removal (OIR) tasks that you must perform on the T1 or E1 feature card.

Describes OIR tasks that you must perform on the channelized T3 (CT3) feature card.

Describes OIR tasks that you must perform on the universal port and dial-only feature cards.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide vii

Preface

Document Conventions

Table 1

Chapter

Chapter 6

Chapter 7

Appendix A

Document Organization (continued)

Title

Voice Feature Card

Troubleshooting

Cabling Specifications

Description

Describes OIR tasks that you must perform on the voice feature card.

Describes how to troubleshoot by using LEDs, bantam jacks, and environmental monitoring.

Describes cabling and pinout information for the dial feature cards.

Document Conventions

This publication uses the following conventions to convey instructions and information.

Convention boldface font

italic font

[ ]

{x | y | z} screen font

boldface screen font

< >

[ ]

Description

Commands and keywords.

Variables for which you supply values.

Keywords or arguments that appear within square brackets are optional.

A choice of required keywords appears in braces separated by vertical bars.

You must select one.

Examples of information displayed on the screen.

Examples of information you must enter.

Nonprinting characters, for example passwords, appear in angle brackets in contexts where italic font is not available.

Default responses to system prompts appear in square brackets.

Note

Means

reader take note

. Notes contain helpful suggestions or references to additional information and material.

Timesaver

This symbol means

the described action saves time

. You can save time by performing the action described in the paragraph.

Caution

This symbol means

reader be careful

.

In this situation, you might do something that could result in equipment damage or loss of data.

Tip

This symbol means

the following information will help you solve a problem

.

The tips information might not be troubleshooting or even an action, but could be useful information, similar to a Timesaver.

viii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

Warning

Waarschuwing

IMPORTANT SAFETY INSTRUCTIONS

This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar with standard practices for preventing accidents. Use the statement number provided at the end of each warning to locate its translation in the translated safety warnings that accompanied this device.

SAVE THESE INSTRUCTIONS

BELANGRIJKE VEILIGHEIDSINSTRUCTIES

Dit waarschuwingssymbool betekent gevaar. U verkeert in een situatie die lichamelijk letsel kan veroorzaken. Voordat u aan enige apparatuur gaat werken, dient u zich bewust te zijn van de bij elektrische schakelingen betrokken risico's en dient u op de hoogte te zijn van de standaard praktijken om ongelukken te voorkomen. Gebruik het nummer van de verklaring onderaan de waarschuwing als u een vertaling van de waarschuwing die bij het apparaat wordt geleverd, wilt raadplegen.

BEWAAR DEZE INSTRUCTIES

Varoitus

Attention

Warnung

TÄRKEITÄ TURVALLISUUSOHJEITA

Tämä varoitusmerkki merkitsee vaaraa. Tilanne voi aiheuttaa ruumiillisia vammoja. Ennen kuin käsittelet laitteistoa, huomioi sähköpiirien käsittelemiseen liittyvät riskit ja tutustu onnettomuuksien yleisiin ehkäisytapoihin. Turvallisuusvaroitusten käännökset löytyvät laitteen mukana toimitettujen käännettyjen turvallisuusvaroitusten joukosta varoitusten lopussa näkyvien lausuntonumeroiden avulla.

SÄILYTÄ NÄMÄ OHJEET

IMPORTANTES INFORMATIONS DE SÉCURITÉ

Ce symbole d'avertissement indique un danger. Vous vous trouvez dans une situation pouvant entraîner des blessures ou des dommages corporels. Avant de travailler sur un équipement, soyez conscient des dangers liés aux circuits électriques et familiarisez-vous avec les procédures couramment utilisées pour éviter les accidents. Pour prendre connaissance des traductions des avertissements figurant dans les consignes de sécurité traduites qui accompagnent cet appareil, référez-vous au numéro de l'instruction situé à la fin de chaque avertissement.

CONSERVEZ CES INFORMATIONS

WICHTIGE SICHERHEITSHINWEISE

Dieses Warnsymbol bedeutet Gefahr. Sie befinden sich in einer Situation, die zu Verletzungen führen kann. Machen Sie sich vor der Arbeit mit Geräten mit den Gefahren elektrischer Schaltungen und den üblichen Verfahren zur Vorbeugung vor Unfällen vertraut. Suchen Sie mit der am Ende jeder

Warnung angegebenen Anweisungsnummer nach der jeweiligen Übersetzung in den übersetzten

Sicherheitshinweisen, die zusammen mit diesem Gerät ausgeliefert wurden.

BEWAHREN SIE DIESE HINWEISE GUT AUF.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide ix

Preface

Document Conventions

Avvertenza

Advarsel

Aviso

¡Advertencia!

Varning!

IMPORTANTI ISTRUZIONI SULLA SICUREZZA

Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di intervenire su qualsiasi apparecchiatura, occorre essere al corrente dei pericoli relativi ai circuiti elettrici e conoscere le procedure standard per la prevenzione di incidenti.

Utilizzare il numero di istruzione presente alla fine di ciascuna avvertenza per individuare le traduzioni delle avvertenze riportate in questo documento.

CONSERVARE QUESTE ISTRUZIONI

VIKTIGE SIKKERHETSINSTRUKSJONER

Dette advarselssymbolet betyr fare. Du er i en situasjon som kan føre til skade på person. Før du begynner å arbeide med noe av utstyret, må du være oppmerksom på farene forbundet med elektriske kretser, og kjenne til standardprosedyrer for å forhindre ulykker. Bruk nummeret i slutten av hver advarsel for å finne oversettelsen i de oversatte sikkerhetsadvarslene som fulgte med denne enheten.

TA VARE PÅ DISSE INSTRUKSJONENE

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você está em uma situação que poderá ser causadora de lesões corporais. Antes de iniciar a utilização de qualquer equipamento, tenha conhecimento dos perigos envolvidos no manuseio de circuitos elétricos e familiarize-se com as práticas habituais de prevenção de acidentes. Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo.

GUARDE ESTAS INSTRUÇÕES

INSTRUCCIONES IMPORTANTES DE SEGURIDAD

Este símbolo de aviso indica peligro. Existe riesgo para su integridad física. Antes de manipular cualquier equipo, considere los riesgos de la corriente eléctrica y familiarícese con los procedimientos estándar de prevención de accidentes. Al final de cada advertencia encontrará el número que le ayudará a encontrar el texto traducido en el apartado de traducciones que acompaña a este dispositivo.

GUARDE ESTAS INSTRUCCIONES

VIKTIGA SÄKERHETSANVISNINGAR

Denna varningssignal signalerar fara. Du befinner dig i en situation som kan leda till personskada.

Innan du utför arbete på någon utrustning måste du vara medveten om farorna med elkretsar och känna till vanliga förfaranden för att förebygga olyckor. Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning.

SPARA DESSA ANVISNINGAR x

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide xi

Preface

Document Conventions

Aviso

Advarsel

INSTRUÇÕES IMPORTANTES DE SEGURANÇA

Este símbolo de aviso significa perigo. Você se encontra em uma situação em que há risco de lesões corporais. Antes de trabalhar com qualquer equipamento, esteja ciente dos riscos que envolvem os circuitos elétricos e familiarize-se com as práticas padrão de prevenção de acidentes. Use o número da declaração fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham o dispositivo.

GUARDE ESTAS INSTRUÇÕES

VIGTIGE SIKKERHEDSANVISNINGER

Dette advarselssymbol betyder fare. Du befinder dig i en situation med risiko for legemesbeskadigelse. Før du begynder arbejde på udstyr, skal du være opmærksom på de involverede risici, der er ved elektriske kredsløb, og du skal sætte dig ind i standardprocedurer til undgåelse af ulykker. Brug erklæringsnummeret efter hver advarsel for at finde oversættelsen i de oversatte advarsler, der fulgte med denne enhed.

GEM DISSE ANVISNINGER xii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Document Conventions

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide xiii

Preface

Obtaining Documentation

Obtaining Documentation

Cisco documentation and additional literature are available on Cisco.com. Cisco also provides several ways to obtain technical assistance and other technical resources. These sections explain how to obtain technical information from Cisco Systems.

Cisco.com

You can access the most current Cisco documentation at this URL: http://www.cisco.com/techsupport

You can access the Cisco website at this URL: http://www.cisco.com

You can access international Cisco websites at this URL: http://www.cisco.com/public/countries_languages.shtml

Product Documentation DVD

The Product Documentation DVD is a comprehensive library of technical product documentation on a portable medium. The DVD enables you to access multiple versions of installation, configuration, and command guides for Cisco hardware and software products. With the DVD, you have access to the same

HTML documentation that is found on the Cisco website without being connected to the Internet.

Certain products also have .PDF versions of the documentation available.

The Product Documentation DVD is available as a single unit or as a subscription. Registered Cisco.com users (Cisco direct customers) can order a Product Documentation DVD (product number

DOC-DOCDVD= or DOC-DOCDVD=SUB) from Cisco Marketplace at this URL: http://www.cisco.com/go/marketplace/

Ordering Documentation

Registered Cisco.com users may order Cisco documentation at the Product Documentation Store in the

Cisco Marketplace at this URL: http://www.cisco.com/go/marketplace/

Nonregistered Cisco.com users can order technical documentation from 8:00 a.m. to 5:00 p.m.

(0800 to 1700) PDT by calling 1 866 463-3487 in the United States and Canada, or elsewhere by calling 011 408 519-5055. You can also order documentation by e-mail at [email protected]

or by fax at 1 408 519-5001 in the United States and Canada, or elsewhere at 011 408 519-5001.

Documentation Feedback

You can rate and provide feedback about Cisco technical documents by completing the online feedback form that appears with the technical documents on Cisco.com.

xiv

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Cisco Product Security Overview

You can submit comments about Cisco documentation by using the response card (if present) behind the front cover of your document or by writing to the following address:

Cisco Systems

Attn: Customer Document Ordering

170 West Tasman Drive

San Jose, CA 95134-9883

We appreciate your comments.

Cisco Product Security Overview

Cisco provides a free online Security Vulnerability Policy portal at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

From this site, you will find information about how to:

Report security vulnerabilities in Cisco products.

Obtain assistance with security incidents that involve Cisco products.

Register to receive security information from Cisco.

A current list of security advisories, security notices, and security responses for Cisco products is available at this URL: http://www.cisco.com/go/psirt

To see security advisories, security notices, and security responses as they are updated in real time, you can subscribe to the Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed. Information about how to subscribe to the PSIRT RSS feed is found at this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html

Reporting Security Problems in Cisco Products

Cisco is committed to delivering secure products. We test our products internally before we release them, and we strive to correct all vulnerabilities quickly. If you think that you have identified a vulnerability in a Cisco product, contact PSIRT:

For Emergencies only — [email protected]

An emergency is either a condition in which a system is under active attack or a condition for which a severe and urgent security vulnerability should be reported. All other conditions are considered nonemergencies.

For Nonemergencies — [email protected]

In an emergency, you can also reach PSIRT by telephone:

1 877 228-7302

1 408 525-6532

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide xv

Preface

Obtaining Technical Assistance

Tip

We encourage you to use Pretty Good Privacy (PGP) or a compatible product (for example, GnuPG) to encrypt any sensitive information that you send to Cisco. PSIRT can work with information that has been encrypted with PGP versions 2.

x

through 9.

x

.

Never use a revoked or an expired encryption key. The correct public key to use in your correspondence with PSIRT is the one linked in the Contact Summary section of the Security Vulnerability Policy page at this URL: http://www.cisco.com/en/US/products/products_security_vulnerability_policy.html

The link on this page has the current PGP key ID in use.

If you do not have or use PGP, contact PSIRT at the aforementioned e-mail addresses or phone numbers before sending any sensitive material to find other means of encrypting the data.

Obtaining Technical Assistance

Cisco Technical Support provides 24-hour-a-day award-winning technical assistance. The Cisco

Technical Support & Documentation website on Cisco.com features extensive online support resources.

In addition, if you have a valid Cisco service contract, Cisco Technical Assistance Center (TAC) engineers provide telephone support. If you do not have a valid Cisco service contract, contact your reseller.

Cisco Technical Support & Documentation Website

The Cisco Technical Support & Documentation website provides online documents and tools for troubleshooting and resolving technical issues with Cisco products and technologies. The website is available 24 hours a day, at this URL: http://www.cisco.com/techsupport

Access to all tools on the Cisco Technical Support & Documentation website requires a Cisco.com user

ID and password. If you have a valid service contract but do not have a user ID or password, you can register at this URL: http://tools.cisco.com/RPF/register/register.do

Note

Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting a web or phone request for service. You can access the CPI tool from the Cisco Technical Support &

Documentation website by clicking the

Tools & Resources

link under Documentation & Tools.

Choose

Cisco Product Identification Tool

from the Alphabetical Index drop-down list, or click the

Cisco

Product Identification Tool

link under Alerts & RMAs. The CPI tool offers three search options: by product ID or model name; by tree view; or for certain products, by copying and pasting

show

command output. Search results show an illustration of your product with the serial number label location highlighted. Locate the serial number label on your product and record the information before placing a service call.

xvi

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Technical Assistance

Submitting a Service Request

Using the online TAC Service Request Tool is the fastest way to open S3 and S4 service requests. (S3 and S4 service requests are those in which your network is minimally impaired or for which you require product information.) After you describe your situation, the TAC Service Request Tool provides recommended solutions. If your issue is not resolved using the recommended resources, your service request is assigned to a Cisco engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest

For S1 or S2 service requests, or if you do not have Internet access, contact the Cisco TAC by telephone.

(S1 or S2 service requests are those in which your production network is down or severely degraded.)

Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

To open a service request by telephone, use one of the following numbers:

Asia-Pacific: +61 2 8446 7411 (Australia: 1 800 805 227)

EMEA: +32 2 704 55 55

USA: 1 800 553-2447

For a complete list of Cisco TAC contacts, go to this URL: http://www.cisco.com/techsupport/contacts

Definitions of Service Request Severity

To ensure that all service requests are reported in a standard format, Cisco has established severity definitions.

Severity 1 (S1)—An existing network is down, or there is a critical impact to your business operations.

You and Cisco will commit all necessary resources around the clock to resolve the situation.

Severity 2 (S2)—Operation of an existing network is severely degraded, or significant aspects of your business operations are negatively affected by inadequate performance of Cisco products. You and Cisco will commit full-time resources during normal business hours to resolve the situation.

Severity 3 (S3)—Operational performance of the network is impaired, while most business operations remain functional. You and Cisco will commit resources during normal business hours to restore service to satisfactory levels.

Severity 4 (S4)—You require information or assistance with Cisco product capabilities, installation, or configuration. There is little or no effect on your business operations.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide xvii

Preface

Obtaining Additional Publications and Information

Obtaining Additional Publications and Information

Information about Cisco products, technologies, and network solutions is available from various online and printed sources.

The

Cisco Product Quick Reference Guide

is a handy, compact reference tool that includes brief product overviews, key features, sample part numbers, and abbreviated technical specifications for many Cisco products that are sold through channel partners. It is updated twice a year and includes the latest Cisco offerings. To order and find out more about the Cisco Product Quick Reference

Guide, go to this URL:

http://www.cisco.com/go/guide

Cisco Marketplace provides a variety of Cisco books, reference guides, documentation, and logo merchandise. Visit Cisco Marketplace, the company store, at this URL:

http://www.cisco.com/go/marketplace/

Cisco Press

publishes a wide range of general networking, training and certification titles. Both new and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com

Packet

magazine is the Cisco Systems technical user magazine for maximizing Internet and networking investments. Each quarter, Packet delivers coverage of the latest industry trends, technology breakthroughs, and Cisco products and solutions, as well as network deployment and troubleshooting tips, configuration examples, customer case studies, certification and training information, and links to scores of in-depth online resources. You can access Packet magazine at this URL: http://www.cisco.com/packet

iQ Magazine

is the quarterly publication from Cisco Systems designed to help growing companies learn how they can use technology to increase revenue, streamline their business, and expand services. The publication identifies the challenges facing these companies and the technologies to help solve them, using real-world case studies and business strategies to help readers make sound technology investment decisions. You can access iQ Magazine at this URL: http://www.cisco.com/go/iqmagazine or view the digital edition at this URL:

http://ciscoiq.texterity.com/ciscoiq/sample/

Internet Protocol Journal

is a quarterly journal published by Cisco Systems for engineering professionals involved in designing, developing, and operating public and private internets and intranets. You can access the Internet Protocol Journal at this URL: http://www.cisco.com/ipj

Networking products offered by Cisco Systems, as well as customer support services, can be obtained at this URL: http://www.cisco.com/en/US/products/index.html

xviii

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Preface

Obtaining Additional Publications and Information

Networking Professionals Connection is an interactive website for networking professionals to share questions, suggestions, and information about networking products and technologies with Cisco experts and other networking professionals. Join a discussion at this URL: http://www.cisco.com/discuss/networking

World-class networking training is available from Cisco. You can view current offerings at this URL: http://www.cisco.com/en/US/learning/index.html

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide xix

Obtaining Additional Publications and Information

Preface xx

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

C H A P T E R

1

Safety Warnings, Recommendations, and Tools

Required

This chapter describes the safety warnings, recommendations, and tools required to install feature cards in the chassis. This chapter contains the following sections:

General Safety, page 1-1

Maintaining Safety with Electricity, page 1-2

Preventing Electrostatic Discharge, page 1-3

Required Tools and Equipment, page 1-3

Where to Go Next, page 1-4

General Safety

Any device that uses electricity must be handled carefully; follow these guidelines to ensure general safety:

Keep the chassis area clear and dust-free during and after installation.

Put the removed chassis cover in a safe place.

Keep tools away from walk areas where you and others could fall over them.

Do not wear loose clothing that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Warning

Ultimate disposal of this product should be handled according to all national laws and regulations.

Statement 1040

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

1-1 78-17406-01

Maintaining Safety with Electricity

Maintaining Safety with Electricity

Chapter 1 Safety Warnings, Recommendations, and Tools Required

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces, and watches). Metal objects will heat up when connected to power and ground and can cause serious burns or weld the metal object to the terminals.

Statement 43

Follow these guidelines when you work on equipment powered by electricity.

Locate the emergency power-OFF switch for the room in which you are working. Then, if an electrical accident occurs, you can act quickly to turn OFF the power.

Before working on the system, unplug the power cord.

Disconnect all power before doing the following:

Installing or removing a feature card

Working near power supplies

Warning

When installing or replacing the unit, the ground connection must always be made first and disconnected last.

Statement 1046

Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit. Always check.

Warning Read the installation instructions before connecting the system to the power source.

Statement 1004

Look carefully for possible hazards in your work area, such as moist floors, ungrounded power extension cables, frayed power cords, and missing safety ground connections.

If an electrical accident occurs, proceed as follows:

Use caution; do not become a victim yourself.

Turn OFF power to the system.

If possible, send another person to get medical aid. Otherwise, assess the condition of the victim and then call for help.

Determine if the person needs rescue breathing or external cardiac compressions; then take appropriate action.

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15A U.S. (240 VAC, 10A international) is used on the phase conductors (all current-carrying conductors).

Statement 13

1-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 1 Safety Warnings, Recommendations, and Tools Required

Preventing Electrostatic Discharge

Preventing Electrostatic Discharge

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs when electronic components are improperly handled and can result in complete or intermittent failures.

Always follow ESD-prevention procedures when you remove and replace components. Ensure that the chassis is electrically connected to earth ground. Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. Connect the grounding clip to an unpainted surface of the chassis frame to safely ground unwanted ESD voltages. To guard against ESD damage and shocks, the wrist strap and cord must operate properly. If no wrist strap is available, ground yourself by touching the metal part of the chassis.

For safety, periodically check the resistance value of the antistatic strap, which should be between 1 and

10 megohm (Mohm).

Required Tools and Equipment

The following items are provided with each universal gateway:

RJ-45-to-DB-9 female DTE adapter (labeled TERMINAL)

RJ-45-to-DB-25 female DTE adapter (labeled TERMINAL)

RJ-45-to-DB-25 male DCE adapter (labeled MODEM)

RJ-45-to-RJ-45 rollover console cable

ESD-preventive wrist strap

Nylon cable tie

Cable tie holder

Grounding lug

Alarm connector

You might need the following equipment, which is not provided with the universal gateway:

Straight-through RJ-45-to-RJ-45 cable for an Ethernet connection

Ethernet hub or PC with a network interface card for Ethernet LAN connections

One breakout cable consisting of a 36-pin connector connected to eight RJ-45 adapters for CT1 or

CE1 connections

Straight-through RJ-45-to-RJ-45 cable for CT1 or CE1 connections

75-ohm coaxial cable for a CT3 connection

PC that is running terminal emulation software for local administrative access

Modem for remote administrative access

ESD-preventive mat

Blank feature card panel

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

1-3

Chapter 1 Safety Warnings, Recommendations, and Tools Required

Where to Go Next

Where to Go Next

The remaining chapters of this guide provide information about installing and troubleshooting feature cards and about building cables.

Chapter 2, “Feature Card and Carrier Card Guidelines”

Chapter 3, “T1 and E1 Feature Cards”

Chapter 4, “Channelized T3 Feature Card”

Chapter 5, “Universal Port and Dial-Only Feature Cards”

Chapter 6, “Voice Feature Card”

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

1-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

C H A P T E R

2

Feature Card and Carrier Card Guidelines

This chapter includes the following sections:

Overview, page 2-1

Online Insertion and Removal of Feature Cards, page 2-2

Getting Help, page 2-7

Where to Go Next, page 2-7

Removing and Installing Populated Carrier Cards, page 2-2

Overview

Cisco AS5350XM Chassis

The Cisco AS5350XM universal gateway chassis has a motherboard, a high-speed backplane, and three slots for feature cards that allow online insertion and removal (OIR).

Cisco AS5400XM Chassis

The Cisco AS5400XM universal gateway chassis has a motherboard, a high-speed backplane, and seven slots for feature cards that allow OIR.

Feature Cards

Each feature card is a 5.1- by 13-inch (13- by 30-cm) PCI-based interface board.

The following trunk types are supported:

T1 feature card—Supports North American robbed-bit signaling (RBS) on T1 trunks, including a variety of North American RBS protocol, framing, and encoding types.

E1 feature card—Supports channel-associated signaling (CAS) for E1 trunks, with R2 signaling.

Many countries require an E1 R2 variant. Per-country defaults are provided for supervisory and inter-register signaling.

Channelized T3 (CT3) feature card—Provides physical line termination for a channelized T3 ingress trunk line, and uses an onboard multiplexer to multiplex 28 channelized T1 lines into a single channelized T3 line.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

2-1 78-17406-01

Chapter 2 Feature Card and Carrier Card Guidelines

Online Insertion and Removal of Feature Cards

The following access types are supported:

Universal port feature card—Converts voice, fax, and dial calls into IP packets or frames by using the Nextport digital signal processor (DSP) modules.

Dial-only feature card—Converts dial calls into IP packets or frames by using the Nextport digital signal processor (DSP) modules.

Voice feature card—Converts voice and fax calls into IP packets or frames by using packet fax or voice digital signal processor (DSP) modules (PVDM2).

Online Insertion and Removal of Feature Cards

All feature cards on the Cisco AS5350XM and Cisco AS5400XM chassis support OIR (also known as hot swapping). You can install, remove, replace, and rearrange the feature cards without turning off the chassis power.

When the chassis detects that a feature card is installed or removed, it automatically runs diagnostic and discovery routines, acknowledges the presence or absence of the feature card, and resumes chassis operation without any operator intervention.

See the following chapters for more information about specific feature cards:

See Chapter 3, “T1 and E1 Feature Cards,” to perform OIR of the T1 or E1 feature card.

See Chapter 4, “Channelized T3 Feature Card,” to perform OIR of the CT3 feature card.

See Chapter 5, “Universal Port and Dial-Only Feature Cards,” to perform OIR of the universal port or dial-only feature card.

See Chapter 6, “Voice Feature Card,” to perform OIR of the voice feature card.

Removing and Installing Populated Carrier Cards

Caution

The carrier cards that carry the feature cards are not hot-swappable. Removing a card while the system is still powered on may cause permanent damage to electronic circuits on the card.

The feature card carrier card plugs into one of the backplane slots and supports two feature cards. The carrier card increases backplane capacity and allows OIR of the feature cards. (See Figure 2-1 .)

Figure 2-1 Carrier Card with Two Feature Cards Installed

NP108

ACT

NP108

ACT

OK

MAINT

2-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 2 Feature Card and Carrier Card Guidelines

Removing and Installing Populated Carrier Cards

Warning Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect the power at the circuit breaker on DC units.

Statement 12

Warning Before performing any of the following procedures, ensure that power is removed from the DC circuit.

Statement 1003

Warning Before connecting or disconnecting ground or power wires to the chassis, ensure that power is removed from the DC circuit. To ensure that all power is OFF, locate the circuit breaker on the panel board that services the DC circuit, switch the circuit breaker to the OFF position, and tape the switch handle of the circuit breaker in the OFF position.

Statement 140

Caution

Before you remove a carrier card, see Chapter 1, “Safety Warnings, Recommendations, and Tools

Required.”

Removing a Populated Carrier Card

Warning Before opening the unit, disconnect the telephone-network cables to avoid contact with telephone-network voltages.

Statement 1041

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

To remove a populated carrier card, follow the steps below:

Step 1

Step 2

Step 3

Power down the chassis.

Disconnect all interface cables from the universal gateway, and secure them out of the way.

Loosen the two captive screws that secure the carrier card to the chassis until each screw is free of the chassis. (See Figure 2-2 and Figure 2-3 .)

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

2-3

Chapter 2 Feature Card and Carrier Card Guidelines

Removing and Installing Populated Carrier Cards

Figure 2-2 Loosening the Captive Screws on the Cisco AS5350XM

Chassis

Captive screw

Figure 2-3

DFC

Carrier card

Captive screw

Loosening the Captive Screws on the Cisco AS5400XM

Chassis

Step 4

Captive screw

DFC

Carrier card

DFC

Captive screw

Grasp the feature card handles and gently pull them toward you to guide the carrier card out of the slot.

Place one hand under the carrier card as you pull it out of the chassis. (See Figure 2-4 and Figure 2-5 .)

Note

Use the feature card handles to remove the carrier card. Ensure that the feature cards are secured to the carrier card.

Figure 2-4 Removing the Carrier Card from the Cisco AS5350XM

2-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 2 Feature Card and Carrier Card Guidelines

Figure 2-5

Removing and Installing Populated Carrier Cards

Removing the Carrier Card from the Cisco AS5400XM

Step 5

Step 6

After you remove the carrier card from the chassis, set it aside on an ESD-preventive mat.

If the backplane slot is to remain empty, install a blank cover over the open slot to ensure proper airflow inside the chassis. (See Figure 2-6 .)

Figure 2-6 Blank Filler Panel

Installing a Populated Carrier Card

To install a populated carrier card:

Step 1

Slide the carrier card into the slot until it touches the backplane connector. (See Figure 2-7 and

Figure 2-8 .)

Figure 2-7 Installing the Carrier Card in the Cisco AS5350XM

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

2-5

Chapter 2 Feature Card and Carrier Card Guidelines

Removing and Installing Populated Carrier Cards

Figure 2-8 Installing the Carrier Card in the Cisco AS5400XM

Step 2

Step 3

Align the captive screws with their holes, and seat the card completely.

Tighten the two captive screws to secure the carrier card to the chassis. (See Figure 2-9 and Figure 2-10 .)

Figure 2-9 Tightening the Captive Screws on the Cisco AS5350XM

Captive screw

Captive screw

Figure 2-10 Tightening the Captive Screws on the Cisco AS5400XM

Captive screw Captive screw

Step 4

If the carrier card has a blank feature card slot, install a blank cover over the open feature card slot to ensure proper airflow inside the chassis. (See Figure 2-11 .)

2-6

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 2 Feature Card and Carrier Card Guidelines

Figure 2-11 Blank Feature Card Cover

Getting Help

Step 5

Step 6

For AC-powered units, reconnect the AC power cord. For DC-powered units, remove the tape from the circuit breaker switch handle, and reinstate power by moving the handle of the circuit breaker to the ON position. For more information about the AC and DC power supplies, see the chassis installation guide for your universal gateway.

Reconnect all interface cables.

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

Where to Go Next

The remaining chapters of this guide include information about installing and troubleshooting feature cards and about building cables.

Chapter 3, “T1 and E1 Feature Cards”

Chapter 4, “Channelized T3 Feature Card”

Chapter 5, “Universal Port and Dial-Only Feature Cards”

Chapter 6, “Voice Feature Card”

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

2-7

Where to Go Next

Chapter 2 Feature Card and Carrier Card Guidelines

2-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

C H A P T E R

3

T1 and E1 Feature Cards

This chapter provides procedures for installing and removing the T1 and E1 feature cards and includes the following sections:

Overview, page 3-1

Online Installation and Removal of the T1 or E1 Feature Card, page 3-2

Configuring Input Impedance for the E1 Feature Card, page 3-11

Getting Help, page 3-12

Where to Go Next, page 3-12

Overview

You can install a T1 or E1 feature card in any feature card slot of the universal gateway chassis. (See

Figure 3-1 through Figure 3-3 .)

Figure 3-1 2-Port T1 or E1 Feature Card

Bantam ports

T1 or E1 ports

0

1

2 PRI

Rx

Tx

ACT

OK

Figure 3-2 4-Port T1 or E1 Feature Card

T1 or E1 ports

Bantam ports

0

1

2

3

4 PRI

Rx

Tx

ACT

OK/

MAINT

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-1

Online Installation and Removal of the T1 or E1 Feature Card

Figure 3-3 8-Port T1 or E1 Feature Card

Chapter 3 T1 and E1 Feature Cards

Note

The Cisco AS5350XM and Cisco AS5400XM universal gateways each support only one type of

WAN feature card at a time. See Chapter 7, “Troubleshooting,” for more information.

Each T1 or E1 feature card provides physical line termination for multiple DS-0 channels and uses onboard HDLC controllers to terminate digital (ISDN) calls. For network specifications, see Table 3-1 and Table 3-2 . You can use the bantam jack ports on the feature card to monitor a line.

Table 3-1 T1 Feature Card Network Specifications

Description

Line rate

Data rate (per port)

Standards

Input impedance

Specification

1.544 Mbps

number

x 56 or

number

x 64 kbps, where

number

= 1 to 24

AT&T Pub. 62411, 54016, and 43081, and ANSI T1.403

100 ohm per port

Table 3-2 E1 Feature Card Network Specifications

Description

Line rate

Data rate (per port)

Input impedance

Specification

2.048 Mbps

number

75 or 120 ohm per port

Note

x 56 or

number

x 64 kbps, where

number

= 1 to 31.

The factory default setting for the E1 ports is 120 ohm. For information about changing the impedance, see the “Configuring

Input Impedance for the E1 Feature Card” section on page 3-11 .

Online Installation and Removal of the T1 or E1 Feature Card

To remove a feature card without dropping any calls or connections, you will need to take the feature card out of service by using the

busyout

command to disable the feature card. The

busyout

command is executed on a per–feature card basis and will disable the card after waiting for the active services to terminate.

If there are active calls on the feature card after you execute the

busyout

command, wait for the calls to drop. To view the status of the termination process, use the

show busyout

command.

3-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

Caution

The online installation and removal (OIR) of new cards should be done

only

during times of low CPU utilization, such as during maintenance.

Caution

To avoid erroneous failure messages, remove or insert only one feature card at a time.

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically.

If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Software Configuration Guide

.

Removing the T1 or E1 Feature Card

To remove the T1 or E1 feature card, follow these steps.

Note

An example showing the output from each command is provided after the procedure. See the “Online

Insertion and Removal Example for the T1 or E1 Feature Card” section on page 3-6 .

Step 1

Determine which slot the feature card is in (see Figure 3-4 and Figure 3-5 ) by entering the

show chassis slot

command in privileged EXEC mode:

Router#

show chassis slot

Note

These commands are not valid for slot 0. Slot 0 is the motherboard.

Figure 3-4 Slot Numbering on the Cisco AS5350XM Chassis

Slot 2

Slot 0

Slot 1

Slot 3

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-3

Online Installation and Removal of the T1 or E1 Feature Card

Figure 3-5 Slot Numbering on the Cisco AS5400XM Chassis

Chapter 3 T1 and E1 Feature Cards

Step 2

Step 3

Step 4

Slot 0

Slot 2

Slot 4

Slot 6

Slot 1

Slot 3

Slot 5

Slot 7

Initialize the software busyout procedure by entering the

busyout

command:

Router#

busyout

slot-number

Check busyout status for the slot, by entering the

show busyout

command.

Router#

show busyout

slot-number

You can use the

clear port

command to immediately disable active calls on a universal port, dial-only, or voice feature card. For more information on the universal port or dial-only feature card, see Chapter 5,

“Universal Port and Dial-Only Feature Cards.” For more information on the voice feature card, see

Chapter 6, “Voice Feature Card.” Use the

show controller

command to show the card that is associated with the T1 or E1 feature card.

Router#

show controller t1/e1

slot-number/control-number

timeslot

timeslot-number

Router#

clear port

slot-number/port number

Note

The

clear port

command applies only to universal port, dial-only, or voice feature cards.

Step 5

Verify that the OK/MAINT LED is off; this indicates that the feature card is offline and ready to be removed.

Note

The OK/MAINT LED is green before you enter the

busyout

command. After you enter the

busyout

command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources are taken out of service, indicating that busyout is complete.

Step 6

Attach an ESD-preventive wrist strap.

Warning Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Step 7

Step 8

Disconnect all interface cables from the feature card and secure them out of the way.

Loosen the two captive screws that secure the feature card to the chassis until each screw is free of the chassis. (See Figure 3-6 and Figure 3-7 .)

3-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 3 T1 and E1 Feature Cards

Figure 3-6

Online Installation and Removal of the T1 or E1 Feature Card

Loosening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

0

1

2 PRI

Rx

Tx

ACT

OK

Captive screw

DFC

Captive screw

Carrier card

Figure 3-7 Loosening the Captive Screws on the Cisco AS5400XM Universal Gateway

78-17406-01

Captive screw

Captive screw

Step 9

Grasp the feature card handle with one hand. Pull the card toward you until the card slides free of the chassis. Grasp the ventilated metal cover with your other hand to support and guide the feature card out of the slot. (See Figure 3-8 and Figure 3-9 .)

Caution

Avoid touching any pins or circuit board components when you remove or install a feature card.

Figure 3-8 Removing the Feature Card from the Cisco AS5350XM Universal Gateway

0

1

2 PRI

Rx

Tx

ACT OK

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-5

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

Figure 3-9 Removing the Feature Card from the Cisco AS5400XM Universal Gateway

Step 10

Step 11

After you remove the feature card from the chassis, set it aside on an ESD-preventive mat.

If the feature card slot is to remain empty, install a blank cover over the open feature card slot to ensure proper airflow inside the chassis. (See Figure 3-10 .)

Figure 3-10 Blank Feature Card Cover

Online Insertion and Removal Example for the T1 or E1 Feature Card

The following output is an example of the online insertion and removal (OIR) process for an E1 feature card in slot 6 of the universal gateway:

Router#

show chassis slot 6

Slot 6:

DFC type is E1 8 PRI DFC

OIR events:

Number of insertions = 0, Number of removals = 0

DFC State is DFC_S_OPERATIONAL

Router#

Router#

busyout 6

Busyout in progress for 6

Router#

show busyout 6

Busyout status for trunk DFC slot = 6:

DFC slot busyout is in progress

(p - pending, s - static(cfg/exec), d - dynamic, n - none)

6/0 :s s p p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/1 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/2 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/3 :s s s s p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/4 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/5 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/6 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/7 :s s p p p p p p p p p p p p p n p p p p p p p p p p p p p p p

Router#

Router#

show controller e1 6/0 timeslot 1-31

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-6 78-17406-01

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

E1 6/0 is up:

DS0 Type Modem Status rxA rxB rxC rxD txA txB txC txD

1 pri - idle

2 pri - idle

3 pri-modem 1/70 active

4 pri-modem 1/46 active

5 pri-modem 1/22 active

6 pri-modem 4/61 active

7 pri-modem 4/53 active

8 pri-modem 4/45 active

9 pri-modem 4/37 active

10 pri-modem 4/29 active

11 pri-modem 4/21 active

12 pri-modem 4/13 active

13 pri-modem 4/05 active

14 pri-modem 2/105 active

15 pri-modem 2/97 active

16 pri-D channel - -

17 pri-modem 2/89 active

18 pri-modem 2/81 active

19 pri-modem 2/73 active

20 pri-modem 2/65 active

21 pri-modem 2/57 active

22 pri-modem 2/49 active

23 pri-modem 2/41 active

24 pri-modem 2/33 active

25 pri-modem 2/25 active

26 pri-modem 2/17 active

27 pri-modem 2/09 active

28 pri-modem 2/01 active

29 pri-modem 1/107 active

30 pri-modem 1/99 active

31 pri-modem 1/91 active

Router#

Router#

show busyout 6

Busyout status for trunk DFC slot = 6:

DFC slot busyout is in progress

(p - pending, s - static(cfg/exec), d - dynamic, n - none)

6/0 :s s p p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/1 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/2 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/3 :s s s s p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/4 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/5 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/6 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/7 :s s p p p p p p p p p p p p p n p p p p p p p p p p p p p p p

Router#

clear port 1/70

This will clear port 1/70[confirm]

*Jan 1 00:27:37.083:%PORT-6-SM_PORT_CLEARED:Port 1/70 Cleared

Router#

show busyout 6

Busyout status for trunk DFC slot = 6:

DFC slot busyout is in progress

(p - pending, s - static(cfg/exec), d - dynamic, n - none)

6/0 :s s s s s s s s s s p p p p p n p p p p p p p p p p p p p p p

6/1 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/2 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/3 :s s s s p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/4 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01 3-7

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

6/5 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/6 :s s s p p p p p p p p p p p p n p p p p p p p p p p p p p p p

6/7 :s s p p p p p p p p p p p p p n p p p p p p p p p p p p p p p

Router#

Router#

*Jan 1 00:32:40.271:%PORT-6-SM_PORT_CLEARED:All Ports Are Cleared

*Jan 1 00:32:40.635:%OIR-6-REMCARD:Card removed from slot 6, interfaces disabled

*Jan 1 00:32:40.643:%TRUNK_CLOCK-6-SWITCH:Switching to the clock on slot 7 port 0 priority 214 as the current primary has gone bad

*Jan 1 00:32:40.647:%CSM-5-PRI:delete PRI at slot 6, unit 0, channel 15 with index 0

*Jan 1 00:32:40.655:%CSM-5-PRI:delete PRI at slot 6, unit 1, channel 15 with index 1

*Jan 1 00:32:40.663:%CSM-5-PRI:delete PRI at slot 6, unit 2, channel 15 with index 2

*Jan 1 00:32:40.667:%CSM-5-PRI:delete PRI at slot 6, unit 3, channel 15 with index 3

*Jan 1 00:32:40.675:%CSM-5-PRI:delete PRI at slot 6, unit 4, channel 15 with index 4

*Jan 1 00:32:40.683:%CSM-5-PRI:delete PRI at slot 6, unit 5, channel 15 with index 4

*Jan 1 00:32:40.687:%CSM-5-PRI:delete PRI at slot 6, unit 6, channel 15 with index 3

*Jan 1 00:32:40.695:%CSM-5-PRI:delete PRI at slot 6, unit 7, channel 15 with index 2

Router#

*Jan 1 00:32:48.515:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/4:15, TEI 0 changed to down

*Jan 1 00:32:48.523:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/5:15, TEI 0 changed to down

*Jan 1 00:32:48.523:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/0:15, TEI 0 changed to down

*Jan 1 00:32:48.523:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/3:15, TEI 0 changed to down

*Jan 1 00:32:48.523:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/6:15, TEI 0 changed to down

*Jan 1 00:32:48.527:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/7:15, TEI 0 changed to down

*Jan 1 00:32:48.527:%ISDN-6-LAYER2DOWN:Layer 2 for Interface Se6/1:15, TEI 0 changed to down

Router#

Router#

show chassis slot 6

Slot 6:

DFC type is Empty DFC

DFC is not powered

OIR events:

Number of insertions = 0, Number of removals = 1

Router#

Router#

show chassis slot 6

Slot 6:

DFC type is E1 8 PRI DFC

OIR events:

Number of insertions = 1, Number of removals = 1

DFC State is DFC_S_OPERATIONAL

3-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

Installing the T1 or E1 Feature Card

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Warning

The E1 interface card may only be installed in an ACA-permitted customer equipment or a Data

Terminal Equipment (DTE) that is exempted from ACA’s permit requirements. The customer equipment must only be housed in a cabinet that has screw-down lids to stop user access to overvoltages on the customer equipment. The customer equipment has circuitry that may have telecommunications network voltages on them.

Statement 90

Warning

The telecommunications lines must be disconnected 1) before unplugging the main power connector and/or 2) while the housing is open.

Statement 89

Note

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

.

To install the T1 or E1 feature card, follow these steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Slide the feature card into the slot until the connector pins make contact with the carrier card backplane connector. (See Figure 3-11 and Figure 3-12 .)

Figure 3-11 Installing the T1 or E1 Feature Card in the Cisco AS5350XM Universal Gateway

0

1

2 PRI

Rx Tx

ACT

OK

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-9

Chapter 3 T1 and E1 Feature Cards

Online Installation and Removal of the T1 or E1 Feature Card

Figure 3-12 Installing the T1 or E1 Feature Card in the Cisco AS5400XM Universal Gateway

Step 3

Step 4

Align the captive screws with their holes, and seat the card completely.

Tighten the screws to secure the feature card to the chassis. (See Figure 3-13 and Figure 3-14 .)

Figure 3-13 Tightening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

0

1

2 PRI

Rx Tx

ACT

OK

Captive screw

DFC

Captive screw

Carrier card

Figure 3-14 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 5

Captive screw

Captive screw

Check the card LEDs to verify that the card is working properly. For information about feature card

LEDs, see Chapter 7, “Troubleshooting.”

3-10

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 3 T1 and E1 Feature Cards

Configuring Input Impedance for the E1 Feature Card

Note

For information about configuring the T1 or E1 ports, see the

Cisco AS5350XM and Cisco AS5400XM

Universal Gateways Software Configuration Guide

.

Configuring Input Impedance for the E1 Feature Card

You can set the input impedance of the E1 feature card before or after running the setup script. For information on configuring the universal gateway with the setup script, see the

Cisco AS5350XM and

Cisco AS5400XM Universal Gateways Software Configuration Guide

.

Configuration

To set the input impedance for the E1 feature card, use the

line-termination

command.

Command

Step 1

Router>

enable

Password:

password

Router#

Step 2

Router#

configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#

Step 3

Router(config)#

controller e1 0

Router(config-controller)#

Purpose

Enters enable mode.

Enter the password. You have entered enable mode when the prompt changes to

Router#

.

Enters global configuration mode. You have entered global configuration mode when the prompt changes to

Router(config)#.

Step 4

Router(config-controller)#

line-termination

75-ohm

Step 5

Router(config-controller)#

Ctrl-Z

Router#

%SYS-5-CONFIG_I: Configured from console by console

Enter the controller number on which you are configuring input impedance.

Sets the input impedance to 75 ohm for the controller.

The factory-set default is 120 ohm. Repeat Step 3 and

Step 4 for the other controllers.

Returns to enable mode.

This message is normal and does not indicate an error.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

3-11

Getting Help

Verification

To verify the impedance, enter the

show running-config

command.

Chapter 3 T1 and E1 Feature Cards

Note

By default, input impedance is 120 ohm. In the following example, the input impedance was successfully changed to 75 ohm using the

line-termination 75-ohm

command. Some of the configuration has been deleted for readability.

Router#

show running-config

Building configuration...

.

.

Current configuration:

.

!

controller E1 0 clock source free-running line-termination 75-ohm

.

.

pri-group timeslots 1-31

!

.

Router#

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

Where to Go Next

The remaining chapters of this guide include information about installing and troubleshooting feature cards and about building cables.

Chapter 4, “Channelized T3 Feature Card”

Chapter 5, “Universal Port and Dial-Only Feature Cards”

Chapter 6, “Voice Feature Card”

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

3-12

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Channelized T3 Feature Card

C H A P T E R

4

This chapter describes the channelized T3 (CT3) feature card and includes the following sections:

Overview, page 4-1

Online Insertion and Removal of the CT3 Feature Card, page 4-2

Getting Help, page 4-7

Where to Go Next, page 4-7

Overview

The CT3 feature card provides physical line termination for a channelized T3 ingress trunk line. It uses an onboard multiplexer to multiplex 28 channelized T1 lines into a single channelized T3 line. (See

Figure 4-1 .)

Figure 4-1 CT3 Feature Card

78-17406-01

Note

The Cisco AS5350XM and Cisco AS5400XM universal gateways each support only one type of

WAN feature card at a time. See Chapter 7, “Troubleshooting,” for more information.

The CT3 feature card provides physical line termination for up to 672 DS0 channels and uses onboard

High-Level Data Link Control (HDLC) controllers to terminate digital (ISDN) calls.

You can use the bantam jack ports on the feature card to monitor a T1 line or to test any of the individual

T1 channels in drop and insert mode.

You can install a CT3 feature card in any feature card slot in a universal gateway chassis.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

4-1

Chapter 4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

To remove a feature card without dropping any calls or connections, you will need to take the feature card out of service by using the

busyout

command to disable the feature card. The

busyout

command is executed on a per–feature card basis and will disable the card after waiting for the active services to terminate.

If there are active calls on the feature card after you execute the

busyout

command, wait for the calls to drop. To view the status of the termination process, use the

show busyout

command.

Caution

The online installation and removal (OIR) of new cards should be done

only

during times of low CPU utilization, such as during maintenance.

Caution

To avoid erroneous failure messages, remove or insert only one feature card at a time.

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically.

If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Software Configuration Guide

.

Removing the CT3 Feature Card

To remove the CT3 feature card, follow these steps.

Note

The OIR procedure for the CT3 feature card is similar to that for the T1 or E1 feature card. See the

“Online Insertion and Removal Example for the T1 or E1 Feature Card” section on page 3-6 for an example of the output during OIR of an E1 feature card.

Step 1

Determine which slot the feature card is in (see Figure 4-2 and Figure 4-3 ) by entering the

show chassis slot

command in privileged EXEC mode:

Router#

show chassis slot

Note

These commands are not valid for slot 0. Slot 0 is the motherboard.

Figure 4-2 Slot Numbering on the Cisco AS5350XM Chassis

Slot 2

Slot 0

Slot 1 Slot 3

4-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 4 Channelized T3 Feature Card

Figure 4-3

Online Insertion and Removal of the CT3 Feature Card

Slot Numbering on the Cisco AS5400XM Chassis

78-17406-01

Slot 0

Slot 2

Slot 4

Slot 6

Slot 1

Slot 3

Slot 5

Slot 7

Step 2

Step 3

Step 4

Initialize the software busyout procedure by entering the

busyout

command:

Router#

busyout

slot-number

Check busyout status for the slot, by entering the

show busyout

command.

Router#

show busyout

slot-number

You can use the

clear port

command to immediately disable active calls on the universal port, dial-only, or voice feature card. For more information on the universal port or dial-only feature card, see Chapter 5,

“Universal Port and Dial-Only Feature Cards.” For more information on the voice feature card, see

Chapter 6, “Voice Feature Card.” Use the

show controller

command to show the feature card that is associated with the CT3 feature card.

Router#

show controller t3

slot-number/control-number

timeslot

timeslot-number

Router#

clear port

slot-number/port number

Step 5

Note

The

clear port

command applies only to universal port, dial-only, or voice feature cards.

Verify that the OK/MAINT LED is off; this indicates that the feature card is offline and ready to be removed.

Step 6

Note

The OK/MAINT LED is green before you enter the

busyout

command. After you enter the

busyout

command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources are taken out of service, indicating that busyout is complete.

Attach an ESD-preventive wrist strap.

Warning

Step 7

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Disconnect all interface cables from the feature card and secure them out of the way.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

4-3

Chapter 4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

Step 8

Note

The OIR procedure for the CT3 feature card is similar to that for the T1 or E1 feature card. See the “Online Insertion and Removal Example for the T1 or E1 Feature Card” section on page 3-6 for an example of the output during OIR of an E1 feature card.

Loosen the two captive screws that secure the feature card to the chassis until each screw is free of the chassis. (See Figure 4-4 and Figure 4-5 .)

Figure 4-4 Loosening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

Figure 4-5 Loosening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 9

Captive screw

Captive screw

Grasp the feature card handle with one hand. Pull the card toward you until the card slides free of the chassis. Grasp the ventilated metal cover with your other hand to support and guide the feature card out of the slot. (See Figure 4-6 and Figure 4-7 .)

Caution

Avoid touching any pins or circuit board components when you remove or install a feature card.

4-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 4 Channelized T3 Feature Card

Figure 4-6

Online Insertion and Removal of the CT3 Feature Card

Removing the Feature Card from the Cisco AS5350XM Universal Gateway

Figure 4-7 Removing the Feature Card from the Cisco AS5400XM Universal Gateway

Step 10

Step 11

After you remove the feature card from the chassis, set it aside on an ESD-preventive mat.

If a feature card slot on the carrier card is to remain empty, install a blank cover over the open feature card slot to ensure proper airflow inside the chassis. (See Figure 4-8 .)

Figure 4-8 Blank Feature Card Cover

Installing the CT3 Feature Card

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Note

When you replace a feature card with a new feature card of the same type in the same slot, the system software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system.

For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

4-5

Chapter 4 Channelized T3 Feature Card

Online Insertion and Removal of the CT3 Feature Card

To install the CT3 feature card, follow these steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Slide the feature card into the slot until the connector pins make contact with the carrier card backplane connector. (See Figure 4-9 and Figure 4-10 .)

Figure 4-9 Installing the CT3 Feature Card in the Cisco AS5350XM Universal Gateway

Figure 4-10 Installing the CT3 Feature Card in the Cisco AS5400XM Universal Gateway

Step 3

Step 4

Align the captive screws with their holes, and seat the card completely.

Tighten the screws to secure the feature card to the chassis. (See Figure 4-11 and Figure 4-12 .)

Figure 4-11 Tightening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

4-6

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 4 Channelized T3 Feature Card

Figure 4-12

Getting Help

Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 5

Captive screw

Captive screw

Check the card LEDs to verify that the card is working properly. For information about feature card

LEDs, see Chapter 7, “Troubleshooting.”

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

Where to Go Next

The remaining chapters of this guide include information about installing and troubleshooting feature cards and about building cables.

Chapter 5, “Universal Port and Dial-Only Feature Cards”

Chapter 6, “Voice Feature Card”

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

4-7

Where to Go Next

Chapter 4 Channelized T3 Feature Card

4-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

C H A P T E R

5

Universal Port and Dial-Only Feature Cards

This chapter describes universal port and dial-only feature cards and includes the following sections:

Overview, page 5-1

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card, page 5-3

System Processing Engine Firmware, page 5-10

Getting Help, page 5-10

Where to Go Next, page 5-10

Overview

Two different types of Nextport digital signal processor (DSP) feature cards are available for

Cisco AS5350XM and Cisco AS5400XM universal gateways. (See Figure 5-1 .)

Universal port feature card—The universal port feature card supports 60 (NP-60) to 108 (NP-108) voice, fax, and dial calls in Cisco AS5350XM and Cisco AS5400XM universal gateways.

Dial-only feature card—The dial-only feature card supports 60 (DL-60) to 108 (DL-108) dial calls in Cisco AS5350XM and Cisco AS5400XM universal gateways. It does not support voice or fax services.

Note

Dial services include modem calls (all modulations), ISDN digital calls, V.110 data calls, and V.120 data calls. Modem pass-through calls are not included in dial services.

For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

. For information on voice and fax commands, see the Cisco IOS Voice

Configuration Library for your Cisco IOS software release at Cisco.com.

You can install a universal port or dial-only feature card in any card slot in the universal gateway chassis.

The universal port and dial-only feature cards do not require external connections.

Note

The dial-only feature card is configured in the same way as the universal port feature card. This allows the dial-only feature card to be used with your existing software configuration.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-1 78-17406-01

Overview

Figure 5-1 Universal Port or Dial-Only Feature Card

Chapter 5 Universal Port and Dial-Only Feature Cards

Note

The versions of the universal port and dial-only feature cards are identified on the card faceplate. The universal port feature card faceplates are labeled NP-60 or NP-108, depending on the number of calls supported. The dial-only feature card faceplates are labeled DL-60 or DL-108, depending on the number of calls supported.

Restrictions for the Universal Port and Dial-Only Feature Cards

If a dial-only feature card is installed in a chassis with the universal port feature card, only the dial services are supported. Table 5-1 describes the behavior of the Cisco AS5350XM and Cisco AS5400XM universal gateways with dial-only feature cards, universal port feature cards, or both types of cards installed in the chassis.

Caution

We do not recommend deploying dial-only feature cards in a chassis that supports voice and fax services, because voice or fax calls assigned to the dial-only feature card will fail.

Note

For information about mixing voice feature cards with the universal port and dial-only feature cards, see the “Restrictions for the Voice Feature Card” section on page 6-2 .

Table 5-1 Features Supported on Universal Port and Dial-Only Feature Cards

Feature Cards Installed

Only dial-only feature cards installed

Only universal port feature cards installed

Both universal port and dial-only feature cards installed

Services Supported

Dial services

Dial, voice, and fax services

Dial services

5-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Online Insertion and Removal of the Universal Port or Dial-Only

Feature Card

To remove a feature card without dropping any calls or connections, you will need to take the feature card out of service by using the

busyout

command to disable the feature card. The

busyout

command is executed on a per–feature card basis and will disable the card after waiting for the active services to terminate.

If there are active calls on the feature card after you execute the

busyout

command, wait for the calls to drop. To view the status of the termination process, use the

show busyout

command.

Caution

The online installation and removal (OIR) of new cards should be done

only

during times of low CPU utilization, such as during maintenance.

Caution

To avoid erroneous failure messages, remove or insert only one feature card at a time.

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically.

If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Software Configuration Guide

. For information on voice and fax commands, see the

Monitoring Voice and Fax Services on the Cisco AS5350 and Cisco AS5400 Universal Gateways

online document.

Removing the Universal Port or Dial-Only Feature Card

To remove the universal port or dial-only feature card, follow these steps.

Note

An example showing the output from each command is provided after the procedure. See the “Online

Insertion and Removal Example for the Universal Port or Dial-Only Feature Card” section on page 5-6 .

Step 1

Determine which slot the feature card is in (see Figure 5-2 and Figure 5-3 ) by entering the

show chassis slot

command in privileged EXEC mode:

Router#

show chassis slot

Note

These commands are not valid for slot 0. Slot 0 is the motherboard.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-3

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Figure 5-2 Slot Numbering on the Cisco AS5350XM Chassis

Slot 2

Slot 0

Slot 1

Slot 3

Figure 5-3 Slot Numbering on the Cisco AS5400XM Chassis

Slot 0

Slot 2

Slot 4

Slot 6

Slot 1

Slot 3

Slot 5

Slot 7

Step 2

Step 3

Step 4

Step 5

Initialize the software busyout procedure by entering the

busyout

command:

Router#

busyout

slot-number

To check busyout status for the slot, enter the

show busyout

command:

Router#

show busyout

slot-number

You can use the

clear port

command to immediately disable active calls on a universal port or dial-only feature card.

Router#

clear port

slot-number/port number

Verify that the OK/MAINT LED is off; this indicates that the feature card is offline and ready to be removed.

Note

The OK/MAINT LED is green before you enter the busyout command. After you enter the

busyout

command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources taken out of service, indicating that

busyout

is complete.

Step 6

Attach an ESD-preventive wrist strap.

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Step 7

Loosen the two captive screws that secure the feature card to the chassis until each screw is free of the chassis. (See Figure 5-4 and Figure 5-5 .)

5-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 5 Universal Port and Dial-Only Feature Cards

Figure 5-4

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Loosening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

Figure 5-5 Loosening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 8

Captive screw

Captive screw

Grasp the feature card handle with one hand. Pull the card toward you until the card slides free of the chassis. Grasp the ventilated metal cover with your other hand to support and guide the feature card out of the slot. (See Figure 5-6 and Figure 5-7 .)

Figure 5-6 Removing the Feature Card from the Cisco AS5350XM Universal Gateway

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-5

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Figure 5-7 Removing the Feature Card from the Cisco AS5400XM Universal Gateway

Caution

Avoid touching any pins or circuit board components when you remove or install a feature card.

Step 9

Step 10

After you remove the feature card, set it aside on an ESD-preventive mat.

If the feature card slot is to remain empty, install a blank cover over the open feature card slot to ensure proper airflow inside the chassis. (See Figure 5-8 .)

Figure 5-8 Blank Feature Card Cover

Online Insertion and Removal Example for the Universal Port or Dial-Only Feature Card

The following output is an example of the online insertion and removal (OIR) process for a universal port feature card in slot 3 of the universal gateway:

Router#

show chassis slot 3

Slot 3:

DFC type is NP108 DFC

OIR events:

Number of insertions = 0, Number of removals = 0

DFC State is DFC_S_OPERATIONAL

Router#

Router#

show busyout 3

Slot 3 is not being busied out

Router#

Router#

busyout 3

Busyout in progress for 3

Router#

Router#

show busyout 3

Slot busyout is in progress

Slot 3:Pending (64 calls remaining)

Router#

Router#

show chassis slot 3

Slot 3:

DFC type is NP108 DFC

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-6 78-17406-01

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

OIR events:

Number of insertions = 0, Number of removals = 0

DFC State is DFC_S_OPERATIONAL

Router#

Router#

clear port 3

This will clear ports 3/00 - 3/107[confirm]

Router#

*Jan 1 00:14:22.555:%PORT-6-SM_PORT_CLEARED:Port 3/00 - 3/107 Cleared

Router#

show busyout 3

Slot busyout is in progress

Slot 3:Pending (54 calls remaining)

Router#

Router#

show busyout 3

Slot busyout is in progress

Slot 3:Pending (36 calls remaining)

Router#

show busyout 3

Slot busyout is in progress

Slot 3:Pending (30 calls remaining)

Router#

clear port 3

This will clear ports 3/00 - 3/107[confirm]

Router#

*JRouteran 1 00:14:59.275:%PORT-6-SM_PORT_CLEARED:Port 3/00 - 3/107 Cleared

Router#

show busyout 3

Slot busyout is in progress

Slot 3:Pending (9 calls remaining)

Router#

clear port 3

*Jan 1 00:15:10.355:%NP_MD-6-MODULE_DOWN:NextPort module 3/0/0 down

*Jan 1 00:15:10.363:%NP_BS-6-MODULE_STOPPED:NextPort module 3/0/0 Stopped

*Jan 1 00:15:10.363:%NP_MD-6-MODULE_DOWN:NextPort module 3/0/1 down

*Jan 1 00:15:10.371:%NP_BS-6-MODULE_STOPPED:NextPort module 3/0/1 Stopped

*Jan 1 00:15:10.371:%NP_MD-6-MODULE_DOWN:NextPort module 3/0/2 down

*Jan 1 00:15:10.379:%NP_BS-6-MODULE_STOPPED:NextPort module 3/0/2 Stopped

*Jan 1 00:15:10.379:%NP_MD-6-SLOT_REMOVED:Slot 3 removed

Router#

clear port 3

*Jan 1 00:15:10.539:%OIR-6-REMCARD:Card removed from slot 3, interfaces disabled

Router#

show chassis slot 3

Slot 3:

DFC type is Empty DFC

DFC is not powered

OIR events:

Number of insertions = 0, Number of removals = 1

Router#

Router#

*Jan 1 00:16:29.047:%OIR-6-INSCARD:Card inserted in slot 3, interfaces administratively shut down

*Jan 1 00:16:29.123:%NP_MD-6-SLOT_INSERTED:Slot 3 (108 ports max) inserted

Router#

*Jan 1 00:16:33.415:%NP_BS-6-MODULE_STARTED:NextPort module 3/0/0 Started - 1.1.3.77

Router#

*Jan 1 00:16:37.843:%NP_BS-6-MODULE_STARTED:NextPort module 3/0/1 Started - 1.1.3.77

*Jan 1 00:16:40.615:%NP_MD-6-MODULE_UP:NextPort module 3/0/0 up

Router#

*Jan 1 00:16:41.847:%NP_BS-6-MODULE_STARTED:NextPort module 3/0/2 Started - 1.1.3.77

Router#

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-7

Chapter 5 Universal Port and Dial-Only Feature Cards

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Router#

show chassis slot 3

Slot 3:

DFC type is NP108 DFC

OIR events:

Number of insertions = 1, Number of removals = 1

DFC State is DFC_S_OPERATIONAL

Installing the Universal Port or Dial-Only Feature Card

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Note

When you replace a feature card with a new feature card of the same type in the same slot, the system software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system.

For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

.

To install the universal port or dial-only feature card, follow these steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Slide the feature card into the slot until the connector pins make contact with the carrier card backplane connector. (See Figure 5-9 and Figure 5-10 .)

Figure 5-9 Installing the Universal Port or Dial-Only Feature Card in the Cisco AS5350XM

Universal Gateway

5-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 5 Universal Port and Dial-Only Feature Cards

Figure 5-10

Online Insertion and Removal of the Universal Port or Dial-Only Feature Card

Installing the Universal Port or Dial-Only Feature Card in the Cisco AS5400XM

Universal Gateway

Step 3

Step 4

Step 5

Align the captive screws with their holes, and then seat the card completely.

Seat the feature card in the carrier by pushing the card firmly until the captive screws are aligned with their holes.

Tighten the screws to secure the feature card to the chassis. (See Figure 5-11 and Figure 5-12 .)

Figure 5-11 Tightening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

Figure 5-12 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway

78-17406-01

Captive screw

Captive screw

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

5-9

Chapter 5 Universal Port and Dial-Only Feature Cards

System Processing Engine Firmware

Step 6

Check the card LEDs to verify that the card is working properly. For information about feature card

LEDs, see Chapter 7, “Troubleshooting.”

System Processing Engine Firmware

System processing engine (SPE) firmware is automatically downloaded to a universal port or dial-only feature card from the Cisco IOS image when you boot the system for the first time, or when you insert a universal port or dial-only feature card while the system is operating. When you insert feature cards while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.

For more information on universal port and dial-only feature card firmware and upgrade options, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide

.

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

Where to Go Next

The remaining chapters of this guide include information about installing and troubleshooting feature cards and about building cables.

Chapter 6, “Voice Feature Card”

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

5-10

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

C H A P T E R

6

Voice Feature Card

This chapter describes the voice feature card and includes the following sections:

Overview, page 6-1

Online Insertion and Removal of the Voice Feature Card, page 6-3

Replacing PVDM2 Modules in the Voice Feature Card, page 6-8

Getting Help, page 6-11

Where to Go Next, page 6-11

Overview

High-density packet voice digital signal processor (DSP) modules (PVDM2) installed on the voice feature card convert voice and fax calls into IP packets or frames that can be transmitted as voice over

IP (VoIP) over a variety of transport technologies on Cisco AS5350XM and Cisco AS5400XM universal gateways. The number of calls supported depends on the number of PVDM2 modules installed on the voice feature card, and the number of voice feature cards installed in the chassis.

The voice feature card supports a 64-channel PVDM2 (AS5X-PVDM2-64) module. You can install up to six AS5X-PVDM2-64 modules on each voice feature card. Table 6-1 describes the maximum number of channels supported by each AS5X-PVDM2-64 module and the maximum number of channels supported by a voice feature card with six AS5X-PVDM2-64 modules installed.

Table 6-1 Maximum Number of Channels Available on a Voice Feature Card with

AS5X-PVDM2-64 Modules

Codec Type

Low complexity (G.711)

Medium complexity (G.726, G.729a,

G.729ab, T.38 fax relay)

High complexity (G.729, G.729b,

G.723.1, GSM-AMR, modem relay)

24

Maximum Number of Channels per AS5X-PVDM2-64

Maximum Number of Channels per Voice Feature Card

64

32

384

192

144

78-17406-01

Note

A Cisco AS5350XM or Cisco AS5400XM universal gateway with the maximum number of PVDM2 modules installed can take up to 6 minutes to boot from power-on to system ready.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-1

Overview

Chapter 6 Voice Feature Card

For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

. For information on voice and fax commands, see the Cisco IOS Voice

Configuration Library for your Cisco IOS software release at Cisco.com.

You can install a voice feature card in any card slot of the universal gateway chassis. The voice feature card does not require external connections. (See Figure 6-1 .)

Figure 6-1 Voice Feature Card

Restrictions for the Voice Feature Card

Voice feature cards are not compatible with universal port and dial-only feature cards. Voice feature cards should not be installed on any system that has universal port and dial-only feature cards. Table 6-2 describes the behavior of the Cisco AS5350XM and Cisco AS5400XM universal gateways depending on whether the voice feature card is present at power on.

Table 6-2 Voice Feature Card Support During Power On

Feature Cards Present at Power On

Voice feature card present at power on

Voice feature card not present at power on

Feature Cards Supported

Voice feature card only. Any universal port and dial-only feature cards present will not be operational until the voice feature card is removed and the system is rebooted.

Universal port or dial-only feature cards only. Any voice feature card installed later will not be operational until the system is rebooted.

6-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 6 Voice Feature Card

Online Insertion and Removal of the Voice Feature Card

Note

If you plan to use voice feature cards, at least one voice feature card must be present when the universal gateway is powered on. More voice feature cards can be installed later.

Online Insertion and Removal of the Voice Feature Card

To remove a feature card without dropping any calls or connections, you will need to take the feature card out of service by using the

busyout

command to disable the feature card. The

busyout

command is executed on a per–feature card basis and will disable the card after waiting for the active services to terminate.

If there are active calls on the feature card after you execute the

busyout

command, wait for the calls to drop. To view the status of the termination process, use the

show busyout

command.

Caution

The online installation and removal (OIR) of new cards should be done

only

during times of low CPU utilization, such as during maintenance.

Caution

To avoid erroneous failure messages, remove or insert only one feature card at a time.

When you replace a feature card with a new feature card of the same type in the same slot, the system software recognizes the new feature card and brings up the interface automatically.

If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal

Gateways Software Configuration Guide

. For information on voice and fax commands, see the

Cisco IOS Voice Configuration Library for your Cisco IOS software release at Cisco.com.

Note

To use the voice feature card, at least one voice feature card must be present when the universal gateway is powered on. More voice feature cards can be inserted later. See the “Restrictions for the Voice Feature

Card” section on page 6-2 for more information.

Removing the Voice Feature Card

To remove the voice feature card, follow these steps.

Note

An example showing the output from each command is provided after the procedure. See the “Online

Insertion and Removal Example for the Voice Feature Card” section on page 6-6 .

Step 1

Determine which slot the feature card is in (see Figure 6-2 and Figure 6-3 ) by entering the

show chassis slot

command in privileged EXEC mode:

Router#

show chassis slot

Note

These commands are not valid for slot 0. Slot 0 is the motherboard.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-3

Online Insertion and Removal of the Voice Feature Card

Figure 6-2 Slot Numbering on the Cisco AS5350XM Chassis

Chapter 6 Voice Feature Card

Slot 2

Slot 0

Slot 1

Slot 3

Figure 6-3 Slot Numbering on the Cisco AS5400XM Chassis

Slot 0

Slot 2

Slot 4

Slot 6

Slot 1

Slot 3

Slot 5

Slot 7

Step 2

Step 3

Initialize the software busyout procedure by entering the

busyout

command:

Router#

busyout

slot-number

Check busyout status for the slot, by entering the

show busyout

command.

Router#

show busyout

slot-number

Timesaver

You can use the

clear voice dsp

command to immediately disable active calls on the voice feature card.

Step 4

Verify that the OK/MAINT LED is off; this indicates that the feature card is offline and ready to be removed.

Note

The OK/MAINT LED is green before you enter the

busyout

command. After you enter the

busyout

command, the LED changes to yellow. The LED turns off after all calls are disconnected and resources taken out of service, indicating that busyout is complete.

Step 5

Attach an ESD-preventive wrist strap.

Warning

Step 6

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Loosen the two captive screws that secure the feature card to the chassis until each screw is free of the chassis. (See Figure 6-4 and Figure 6-5 .)

6-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 6 Voice Feature Card

Figure 6-4

Online Insertion and Removal of the Voice Feature Card

Loosening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

Figure 6-5 Loosening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 7

Captive screw

Captive screw

Grasp the feature card handle with one hand. Pull the card toward you until the card slides free of the chassis. Grasp the sheet metal on each side of the feature card with your other hand to support and guide the feature card out of the slot. (See Figure 6-6 and Figure 6-7 .)

Figure 6-6 Removing a Feature Card from the Cisco AS5350XM Universal Gateway

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-5

Chapter 6 Voice Feature Card

Online Insertion and Removal of the Voice Feature Card

Figure 6-7 Removing a Feature Card from the Cisco AS5400XM Universal Gateway

Caution

Avoid touching any pins or circuit board components when you remove or install a feature card.

Step 8

Step 9

After you remove the feature card, set it aside on an ESD-preventive mat.

If the feature card slot is to remain empty, install a blank cover over the open card slot to ensure proper airflow inside the chassis. (See Figure 6-8 .)

Figure 6-8 Blank Feature Card Cover

Online Insertion and Removal Example for the Voice Feature Card

The following output is an example of the online insertion and removal (OIR) process for a voice feature card in slot 3 of the universal gateway:

Router#

show chassis slot 3

Slot 3:

DFC type is AS5400XM AS5X-FC

OIR events:

Number of insertions = 0, Number of removals = 0

DFC State is DFC_S_OPERATIONAL

Router#

busyout 3

Busyout in progress for 3

Router#

show busyout 3

OIR cleanup in progress for slot 3.

Router#

show busyout 3

DFC in slot 3 is powered down.

Router#

show chassis slot 3

Slot 3:

DFC type is AS5400XM AS5X-FC

DFC is not powered

6-6

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 6 Voice Feature Card

Online Insertion and Removal of the Voice Feature Card

OIR events:

Number of insertions = 0, Number of removals = 1

DFC State is DFC_S_REMOVED

Installing the Voice Feature Card

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity.

Statement 1001

Note

When you replace a feature card in a slot with a new feature card of the same type, the system software recognizes the new feature card and brings up the trunk interfaces automatically. If you replace the existing feature card with a new feature card of a different type, you must reconfigure the system. For configuration details, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software

Configuration Guide

.

To install the voice feature card, follow these steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Slide the feature card into the slot until the connector pins make contact with the carrier card backplane connector. (See Figure 6-9 and Figure 6-10 .)

Figure 6-9 Installing a Feature Card in the Cisco AS5350XM Universal Gateway

Figure 6-10 Installing a Feature Card in the Cisco AS5400XM Universal Gateway

78-17406-01

Step 3

Step 4

Step 5

Align the captive screws with their holes, and then seat the card completely.

Seat the feature card in the carrier by pushing the card firmly until the captive screws are aligned with their holes.

Tighten the screws to secure the feature card to the chassis. (See Figure 6-11 and Figure 6-12 .)

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-7

Chapter 6 Voice Feature Card

Replacing PVDM2 Modules in the Voice Feature Card

Figure 6-11 Tightening the Captive Screws on the Cisco AS5350XM Universal Gateway

Chassis

Captive screw

DFC

Captive screw

Carrier card

Figure 6-12 Tightening the Captive Screws on the Cisco AS5400XM Universal Gateway

Step 6

Captive screw

Captive screw

Check the OK/MAINT LED to verify that the card is working properly. For information about the voice feature card LED, see the “LEDs” section on page 7-1 .

Note

To use the voice feature card, at least one voice feature card must be present when the universal gateway is powered on. More voice feature cards can be inserted later. See the “Restrictions for the Voice Feature Card” section on page 6-2 for more information.

Replacing PVDM2 Modules in the Voice Feature Card

The voice feature card contains six 80-pin SIMM sockets for PVDM2 modules, numbered 0 through 5.

(See Figure 6-13 .) Each socket can be filled with a single 80-pin PVDM2 module.

Note

The voice feature card supports a 64-channel PVDM2 (AS5X-PVDM2-64) module.

6-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 6 Voice Feature Card

Figure 6-13 PVDM2 Slot Locations

5

Replacing PVDM2 Modules in the Voice Feature Card

4 3

2 1 0

Orienting the PVDM2 Module During Installation

The PVDM2 modules are manufactured with a polarization notch to ensure proper orientation, and with alignment holes to ensure proper positioning. Figure 6-14 shows the polarization notch and alignment holes on a PVDM2 module. PVDM2 modules are installed with the connector edge down.

Caution

To avoid damaging ESD-sensitive components, observe all ESD precautions. To avoid damaging the voice feature card, avoid using excessive force when you remove or replace PVDM2 modules.

Figure 6-14 PVDM2 Orientation

Alignment holes

Connector edge

Alignment notch

Polarization notch

Removing PVDM2 Modules From the Voice Feature Card

To remove PVDM2 modules from the voice feature card, perform the following steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Find the appropriate PVDM2 slot on the voice feature card. (See Figure 6-13 .)

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-9

Chapter 6 Voice Feature Card

Replacing PVDM2 Modules in the Voice Feature Card

Caution

Handle PVDM2 modules by the card edges only. PVDM2 modules are ESD-sensitive components and can be damaged by mishandling.

Step 3

Step 4

Step 5

Remove one PVDM2 module at a time. To lift the PVDM2 module out of its socket, pull the locking spring clips on both sides outward and tilt the PVDM2 up, free of the clips.

Hold the PVDM2 module by the edges with your thumb and index finger and lift it out of the socket.

Place the removed PVDM2 module in an antistatic bag to protect it from ESD damage.

Repeat Step 2 through Step 4 for each PVDM2 module you are removing.

Installing PVDM2 Modules in the Voice Feature Card

To install PVDM2 modules in the voice feature card, perform the following steps:

Step 1

Step 2

Attach an ESD-preventive wrist strap.

Find the appropriate PVDM2 slot on the voice feature card. (See Figure 6-13 .)

Caution

Handle PVDM2 modules by the card edges only. PVDM2 modules are ESD-sensitive components and can be damaged by mishandling.

Step 3

Hold the PVDM2 module with the polarization notch pointing toward the back of the voice feature card, with the connector edge pointing down. (See Figure 6-14 .)

Caution

It is normal to feel some resistance, but do not use excessive force to install the PVDM2 module into the socket, and do not touch the surface components. If the PVDM2 module does not fit easily into the socket, remove it and check the orientation of the alignment holes and polarization notch.

Step 4

Step 5

Insert the PVDM2 module into the connector slot at approximately a 45 degree angle to the voice feature card. (See Figure 6-15 .) Gently press the PVDM2 module down, using as little force as possible. When the PVDM2 module is properly seated, the socket guide posts fit through the alignment holes, and the connector springs click into place.

Ensure that each PVDM2 module is straight and that the alignment holes (as shown in Figure 6-15 ) line up with the plastic guides on the socket.

6-10

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 6 Voice Feature Card

Digital Signal Processor Firmware

Figure 6-15 Installing PVDM2 Modules in the Voice Feature Card

View from front of board

1. Insert the PVDM2 into the socket at an angle from vertical.

2. Push the top of the PVDM2 down and back.

3.

The socket guide posts fit through the holes in the PVDM2.

4.

The locking springs clip the back of the PVDM2.

Step 6

Repeat Step 2 through Step 5 for each PVDM2 module.

Note

When the voice feature card is installed and running, you can check that the PVDM2 modules are installed correctly by entering the

show voice dsp summary

command. If an installed

PVDM2 module is missing from the output, try reseating the PVDM2 module.

Digital Signal Processor Firmware

Digital signal processor (DSP) firmware is automatically downloaded to the voice feature card from the

Cisco IOS image when you boot the system for the first time, or when you insert a voice feature card while the system is operating. When you insert feature cards while the system is operating, the Cisco IOS image recognizes the cards and downloads the required firmware to the cards.

For more information on voice feature card firmware and upgrade options, see the

Cisco AS5350XM and

Cisco AS5400XM Universal Gateways Software Configuration Guide

.

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

Where to Go Next

The remaining chapters of this guide include information on troubleshooting feature cards and building cables.

Chapter 7, “Troubleshooting”

Appendix A, “Cabling Specifications”

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

6-11

Where to Go Next

Chapter 6 Voice Feature Card

6-12

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

LEDs

C H A P T E R

7

Troubleshooting

This chapter describes how to troubleshoot the universal gateway by referring to the LEDs on feature cards and using the bantam jack ports. The chapter contains the following sections:

LEDs, page 7-1

Mixing WAN Feature Cards, page 7-5

Mixing Universal Port and Dial-Only Feature Cards, page 7-6

Mixing Voice Feature Cards With Universal Port and Dial-Only Feature Cards, page 7-6

Monitoring the Chassis Environment, page 7-7

Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards, page 7-10

Using Drop and Insert Mode on the CT3 Feature Card, page 7-10

Troubleshooting Network Interfaces, page 7-11

Getting Help, page 7-11

The LEDs indicate the current operating condition of the feature cards. Observe the LEDs (see

Figure 7-1 through Figure 7-4 ), note any fault condition that the product is encountering, and then contact your system administrator or a customer service representative. (See the “Obtaining Technical

Assistance” section on page xvi , if necessary.) Table 7-1 describes the LEDs.

Figure 7-1 2-Port or 4-Port T1 or E1 Feature Card LEDs (2-Port T1 or E1 Feature Card Shown)

0

0

1

1

ACTIVITY (ACT)

OK/MAINT

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-1 78-17406-01

LEDs

Figure 7-2 8-Port T1 or E1 Feature Card LEDs

LNK

Figure 7-3

Local alarm,

Remote alarm, or

Loopback LED for each T1/E1 port

ACTIVITY (ACT)

OK/MAINT

Channelized T3 (CT3) Feature Card LEDs

Chapter 7 Troubleshooting

Loop

LOS

EN/DIS

RA

LA

MA

LNK

ACTIVITY (ACT)

OK/MAINT

Figure 7-4 Universal Port Feature Card, Dial-Only Feature Card, and Voice Feature Card LEDs

ACTIVITY (ACT)

OK/MAINT

7-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 7 Troubleshooting

LEDs

Table 7-1 LEDs

Feature Card

T1 or E1 feature card

LED

ACTIVITY (ACT)

OK/MAINT

Remote Alarm (RA)

Local Alarm (LA)

Loopback (LB)

State

Fast flicker (green)

Description

The feature card is up and running.

Slow flicker (green) The feature card is not yet fully functional.

Green The feature card has passed initial power-up diagnostics tests and is operating normally.

Yellow

The feature card is busied out, but there are active calls. Once all the calls are terminated the feature card will be powered off.

Off

On (yellow)

The feature card is not functioning correctly.

All calls associated with the card have been shut down, and it is safe to remove the card with the system powered on.

One LED below each T1/E1 port indicates one of the following:

A local or remote loopback diagnostic test is running on the associated T1 port.

An alarm has been received on the associated T1/E1 port, indicating loss of signal (LOS) or loss of multiframe alignment (LOF) at the local or remote node.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-3

Chapter 7 Troubleshooting

LEDs

Table 7-1 LEDs (continued)

Feature Card LED

CT3 feature card

ACTIVITY (ACT)

OK/MAINT

State

Fast flicker

Slow flicker

On (green)

Yellow

M13 Alarm (MA)

Off

On

Remote Alarm (RA)

Local Alarm (LA)

T3 EN/DIS

Low signal (LOS)

Network Loop (LOOP)

Off

On

Off

On

Off

Green

Yellow

On

Off

On

Off

Description

The feature card is up and running.

The feature card is not yet fully functional.

The feature card passed initial power-up diagnostics tests and is operating normally.

The feature card is busied out, but there are active calls. Once all the calls are terminated the feature card will be powered off.

The feature card is not functioning correctly.

All calls associated with the feature card have been shut down, and it is safe to remove the card with the system powered on.

One of the following is present on the T3 line:

Received alarm indication signal (RAIS)

Loss of signal (LOS)

Receive RED alarm (RRED)

Far-end receive failure (RFERF)

1

The operating condition is normal.

A T1 alarm condition has been encountered by software.

The operating condition is normal.

A T1 alarm condition has been encountered by software for a particular port.

The operating condition is normal.

A CT3 feature card line connection exists, enabling normal operation.

Normal operation is disabled.

The T3 line interface unit (LIU) is experiencing a loss of signal.

Remains off when operating condition is normal.

At least one T1 is unavailable.

The operating condition is normal.

7-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 7 Troubleshooting

Mixing WAN Feature Cards

Table 7-1 LEDs (continued)

Feature Card

Universal port and dial-only feature card

Voice feature card

LED

ACTIVITY (ACT)

OK/MAINT

ACTIVITY

OK/MAINT

State

Flickering

Green

Yellow

Off

Green (blinking)

Off

Green

Yellow

Off

Description

There is call activity on the feature card.

The feature card passed initial power-up diagnostic tests and is operating normally.

The feature card is busied out, but there are active calls. Once all the calls are terminated the feature card will be powered off.

The feature card is not functioning correctly.

All calls associated with the feature card have been shut down, and it is safe to remove the card with the system powered on.

There is call activity on the feature card.

There is no activity on the feature card.

The feature card passed initial power-up diagnostic tests and is operating normally.

The feature card is busied out, but there are active calls. Once all the calls are terminated the feature card will be powered off.

The feature card is not functioning correctly.

All calls associated with the feature card have been shut down, and it is safe to remove the card with the system powered on.

1.

To display information about an M13 alarm, use the

show controllers t3

user EXEC command.

Mixing WAN Feature Cards

The Cisco AS5350XM and Cisco AS5400XM universal gateways support only one type of WAN feature card at a time. The feature cards that can be installed at one time are:

Up to three T1 feature cards (any combination of 2-, 4-, or 8-port) or

Up to three E1 feature cards (any combination of 2-, 4-, or 8-port) or

One CT3 feature card or

One CT3 feature card and up to two T1 feature cards (any combination of 2-, 4-, or 8-port)

The universal gateway software recognizes feature cards in the order of the slots they are in. For example, a feature card in slot 2 is recognized before a feature card in slot 3. The system recognizes whether there is a mix of WAN feature cards during both power up and OIR:

During power up, the first WAN feature card recognized by the system is the only type brought up.

If there are two or more WAN feature cards of the same type and one is hot-swapped with another of a different type, the new one is not recognized.

In both situations, an error message will appear on the console that is similar to this example:

00:01:12:%CARRIER-2-T1_E1_MIX:Cannot mix T1 and E1 8PRI DFC cards in chassis, do not power up invalid card in slot 7

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-5

Chapter 7 Troubleshooting

Mixing Universal Port and Dial-Only Feature Cards

Mixing Universal Port and Dial-Only Feature Cards

If a dial-only feature card is installed in a chassis with the universal port feature card, only dial services are supported. Table 7-2 describes the behavior of the Cisco AS5350XM and Cisco AS5400XM universal gateways with dial-only feature cards, universal port feature cards, or both installed in the chassis.

Caution

We do not recommend deploying dial-only feature cards in a chassis that supports voice and fax services, because voice or fax calls assigned to the dial-only feature card will fail.

Table 7-2 Universal Port and Dial-Only Feature Card Supported Features

Feature Cards Installed

Only dial-only feature cards installed

Only universal port feature cards installed

Both universal port and dial-only feature cards installed

Services Supported

Dial services

Dial, voice, and fax services

Dial services

Mixing Voice Feature Cards With Universal Port and Dial-Only

Feature Cards

Voice feature cards are not compatible with universal port and dial-only feature cards. Voice feature cards should not be installed on any system that has universal port and dial-only feature cards. Table 7-3 describes the behavior of the Cisco AS5350XM and Cisco AS5400XM universal gateways depending on whether the voice feature card is present at power on.

Table 7-3 Voice Feature Card Support During Power On

Feature Cards Present at Power On

Voice feature card present at power on

Voice feature card not present at power on

Feature Cards Supported

Voice feature card only. Any universal port and dial-only feature cards present will not be operational until the voice feature card is removed and the system is rebooted.

Universal port or dial-only feature cards only. Any voice feature card installed later will not be operational until the system is rebooted.

Note

If you plan to use voice feature cards, at least one voice feature card must be present when the universal gateway is powered on. More voice feature cards can be installed later.

7-6

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 7 Troubleshooting

Monitoring the Chassis Environment

Monitoring the Chassis Environment

The Cisco AS5350XM and Cisco AS5400XM universal gateways contain temperature sensors to detect abnormal temperature conditions during system operation. The three levels of sensor detection are as follows:

1.

When the operating temperature of the system exceeds 113

°

F (45

°

C), the system reaches a warning state. A warning message appears on the console. When the operating temperature of the system drops below 113

°

F (45

°

C), another message is displayed on the console, indicating a recovery. At this level of sensor detection, there is no disruption in system operation.

2.

When the operating temperature of the system continues to rise above 113

°

F (45

°

C) and reaches a temperature of 140

°

F (60

°

C), the system reaches a critical state.

Cisco IOS software busys out the feature cards in the chassis and shuts down the first feature card.

If the operating temperature continues to be critical after 10 minutes, Cisco IOS software shuts down another feature card.

Note

Feature card slot numbering starts at the system board and slots are numbered sequentially from the bottom row up, left to right. Slot 0 is reserved for the motherboard. (See Figure 7-5 and

Figure 7-6 .)

Figure 7-5 Slot Numbering on the Cisco AS5350XM Chassis

Figure 7-6

Slot 2

Slot 0

Slot 1

Slot 3

Slot Numbering on the Cisco AS5400XM Chassis

78-17406-01

Slot 0

Slot 2

Slot 4

Slot 6

Slot 1

Slot 3

Slot 5

Slot 7

The busyout process is repeated at 10-minute intervals until the final feature card is shut down. The console displays the slot number of the feature card and the type of feature card that was shut down.

If the operating temperature cools down to 113

°

F (45

°

C), Cisco IOS software powers on the first feature card, repeating the process for each feature card at 10-minute intervals.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-7

Chapter 7 Troubleshooting

Monitoring the Chassis Environment

3.

When the operating temperature of the system rises above 149

°

F (65

°

C), Cisco IOS software shuts down all feature cards immediately.

Displaying Environment Status

You can use the command-line interface (CLI) to check environment monitoring status of your universal gateway.

To check environment status, enter the

show environment

command in privileged EXEC mode.

Router#

show environment

The output shown below displays on your console during normal operating conditions. The slot number corresponds to the feature card in that slot. The outlet and inlet sensors read the temperature of the air circulating inside the chassis.

Router#

show environment

Temperature:

Temperature Reading:

Temperature at inlet is measured as 22C/71F.

Temperature at outlet is measured as 27C/80F.

Temperature State:

Temperature is in normal state.

Fans:

Fans temperature delta is measured as 5C.

All fans are running well.

Power Supply:

Redundant Power System is present.

The output shown below displays on your console when the system reaches a warning state:

Router#

show environment

Temperature:

Temperature Reading:

Temperature at inlet is measured as 52C/125F.

Temperature at outlet is measured as 64C/147F.

Temperature State:

Temperature is in warning state.

Fans:

Fans temperature delta is measured as 6C.

All fans are running well.

Power Supply:

Redundant Power System is present.

RPS Input Voltage status: normal

RPS Output Voltage status: normal

RPS Fan status: normal

RPS Thermal status: normal

RPS OverVoltage status: normal

Environmental monitor experienced the following events:

Temperature:sensor failed.

Fans:monitor dropped.

Temperature:warning.

Temperature:sensor recovered.

Fans:monitor recovered.

Fans:normal.

The output shown below displays on your console when the system reaches a critical state:

Router#

show environment

Temperature:

Temperature Reading:

Temperature at inlet is measured as 62C/143F.

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-8 78-17406-01

Chapter 7 Troubleshooting

Monitoring the Chassis Environment

Temperature at outlet is measured as 74C/165F.

Temperature State:

Temperature is in critical state.

DFC Busyout/Power-down:

A DFC is powered down. Slot:1, Type:NP108 DFC

A DFC is busyout. Slot:2, Type:T1 8 PRI DFC

A DFC is busyout. Slot:3, Type:NP108 DFC

Fans:

Fans temperature delta is measured as 6C.

All fans are running well.

Power Supply:

Redundant Power System is present.

RPS Input Voltage status: normal

RPS Output Voltage status: normal

RPS Fan status: normal

RPS Thermal status: normal

RPS OverVoltage status: normal

Environmental monitor experienced the following events:

Temperature:sensor failed.

Fans:monitor dropped.

Temperature:warning.

Temperature:sensor recovered.

Fans:monitor recovered.

Fans:normal.

Temperature:critical.

The output shown below displays on your console when the system reaches a shutdown state:

Router#

show environment

Temperature:

Temperature Reading:

Temperature at inlet is measured as 70C/158F.

Temperature at outlet is measured as 82C/179F.

Temperature State:

Temperature is in shutdown state.

DFC Busyout/Power-down:

A DFC is powered down. Slot:1, Type:NP108 DFC

A DFC is powered down. Slot:2, Type:T1 8 PRI DFC

A DFC is powered down. Slot:3, Type:NP108 DFC

Fans:

Fans temperature delta is measured as 6C.

All fans are running well.

Power Supply:

Redundant Power System is present.

RPS Input Voltage status: normal

RPS Output Voltage status: normal

RPS Fan status: normal

RPS Thermal status: normal

RPS OverVoltage status: normal

Environmental monitor experienced the following events:

Temperature:sensor failed.

Fans:monitor dropped.

Temperature:warning.

Temperature:sensor recovered.

Fans:monitor recovered.

Fans:normal.

Temperature:critical.

Temperature:shutdown.

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-9

Chapter 7 Troubleshooting

Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature Cards

Using the Bantam Jack Ports to Monitor T1, E1, and CT3 Feature

Cards

Monitor mode is available on the T1, E1, and CT3 feature cards. If a T1 controller does not come up, or if a large number of errors are associated with a particular controller, you might be able to use the test port to determine whether the problem is in the feature card or in an external T1 line. by using the test port. The test port is a set of bantam jack ports located on the front panel of the T1, E1, and CT3 feature cards. (See Figure 7-7 .)

Figure 7-7 Bantam Jack Ports

Bantam ports

T1 or E1 ports

0

1

2 PRI

Rx

Tx

ACT

OK

In monitor mode, you can monitor only the ingress side of the T1 line without disrupting that line.

The bantam jack ports located on the front panel of the feature cards allow the connection of an external test device (for example, a FIREBERD test device) to monitor the individual T1 circuits in monitor mode. Use software commands to select a T1 line. For information on software commands, see the

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Software Configuration Guide

.

Passive monitoring equipment is used to listen on the TX MON and RX MON jacks during regular operation to detect T1 errors.

Connecting test equipment to the following bantam jack ports provides various functions:

TX MON can monitor signals coming out of the test port without interrupting normal data transmission.

RX MON can monitor signals going in to the test port without interrupting normal data transmission.

Using Drop and Insert Mode on the CT3 Feature Card

The bantam jack ports located on the front panel of the CT3 feature card allow the connection of an external test device (for example, a FIREBERD test device) to test any of the 28 individual T1 circuits in drop and insert mode. Once drop and insert mode is enabled, a T1 circuit can be dropped out of service by using the push button on the CT3 feature card.

The

test trunk drop-insert

privileged EXEC command is used to enable or disable drop and insert mode on a T3 controller. When the system initially boots up, the drop and insert mode is disabled on all T3 controllers.

To drop a T1 circuit to a test port, follow these steps:

Step 1

Enable drop and insert mode by entering the

test trunk drop-insert on

port-number

privileged EXEC command as follows:

Router#

test trunk drop-insert on

port-number

7-10

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Chapter 7 Troubleshooting

Troubleshooting Network Interfaces

Step 2

Note

The

port-number

is the T1 circuit that you wish to drop. T1 port numbers range from 1 to 28.

Disable drop and insert mode after testing the T1 circuits.

Note

We recommend that you disable drop and insert mode to prevent accidental use of the push button on the CT3 feature card.

To disable drop and insert mode, enter the

test trunk drop-insert off

port-number

privileged EXEC command as follows:

Router>

test trunk drop-insert off

port-number

Troubleshooting Network Interfaces

For information about isolating problems with the network connections to your universal gateway, see the

Internetwork Troubleshooting Guide

publication available on Cisco.com.

Getting Help

For information about technical support, onsite service, and exchange and repair services, see the

“Obtaining Technical Assistance” section on page xvi .

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

7-11

Getting Help

Chapter 7 Troubleshooting

7-12

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

A P P E N D I X

A

Cabling Specifications

This appendix provides cabling and pinout information for feature cards on the Cisco AS5350XM and

Cisco AS5400XM universal gateways. It contains the following sections:

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts, page A-1

8-Port T1 or E1 Feature Card Cable and Port Pinouts, page A-6

CT3 Feature Card Cable and Port Pinouts, page A-12

Bantam Jack Port Pinouts, page A-13

Note

This appendix specifies pinouts only for the pins used. Pins not listed in the tables in this appendix are not connected.

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

Table A-1 lists the T1 or E1 feature card port pinouts.

Table A-1 T1 or E1 Feature Card Port Pinouts

6

7

8

4

5

2

3

RJ-45 Pin

1

Description

RX tip

RX ring

RX shield

TX tip

TX ring

TX shield

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-1 78-17406-01

Appendix A Cabling Specifications

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

Table A-2 lists the cable assemblies available for the T1 and E1 feature cards.

Table A-2 T1 and E1 Cable Assemblies

Cable Description

RJ-45 to DB-15

Part Number

72-1336-01

RJ-45 to DB-15 null 72-1337-01

RJ-45 to BNC 72-1338-01

RJ-45 to twinax

RJ-45 to RJ-45TE

72-1339-01

72-1340-01

RJ-45 to RJ-45NT

RJ-45 to RJ-45T1

RJ-45 to bare wire

72-1341-01

72-1342-01

72-1343-01

Product Number

CAB-E1-RJ45DB15

CAB-E1-RJ45DB15N

CAB-E1-RJ45BNC

CAB-E1-RJ-45TWIN

CAB-E1-RJ45TE

CAB-E1-RJ45NT

CAB-E1-RJ45RJ45

CAB-T1-RJJ45BARE

Figure A-1 through Figure A-5 show the types of cables that can connect to the RJ-45 connector on the

T1 or E1 feature card.

Figure A-1 RJ-45-to-DB-15 Cable Assembly

J2

J1

Table A-3 lists the RJ-45-to-DB-15 cable pinouts.

Table A-3 RJ-45-to-DB-15 Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Shell/Braid

Twisted Pair #1

Twisted Pair #1

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Direction

<—

<—

—>

—>

Table A-4 lists the RJ-45-to-DB-15 null modem cable pinouts.

Table A-4 RJ-45-to-DB-15 Null Modem Cable Pinouts

RJ-45 Pin

Shield

J1-1

Signal

Ground

RX Tip

Description

Shell/Braid

Twisted Pair #1

Direction

<—

A-2

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

DB-15 Pin

Shell

J2-3

J2-11

J2-4

J2-1

J2-9

J2-2

DB-15 Pin

Shell

J2-1

78-17406-01

Appendix A Cabling Specifications

Table A-4

RJ-45 Pin

J1-2

J1-3

J1-4

J1-5

J1-6

Figure A-2

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

RJ-45-to-DB-15 Null Modem Cable Pinouts (continued)

Signal

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Twisted Pair #1

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Direction

<—

—>

—>

DB-15 Pin

J2-9

J2-2

J2-3

J2-11

J2-4

RJ-45-to-BNC Cable Assembly for 75-Ohm, Unbalanced Connections

RX

J1

TX

Table A-5 lists the RJ-45-to-BNC cable pinouts.

Table A-5 RJ-45-to-BNC Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Figure A-3

J1

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Shell

Twisted Pair #1

Twisted Pair #1

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Direction

<—

<—

—>

—>

BNC Pin

RX, TX Shields

RX-Tip

RX-Shield

RX-Shield

TX-Tip

TX-Shield

TX-Shield

RJ-45 to Twinax Cable Assembly for 120-Ohm, Balanced Connections

RX

TX

Table A-6 lists the RJ-45 to twinax cable pinouts.

Table A-6 RJ-45 to Twinax Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

Signal

Ground

RX Tip

RX Ring

Description

Shell

Twisted Pair #1

Twisted Pair #1

Direction

<—

<—

Twinax Pin

RX, TX Shields

RX-1

RX-2

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-3

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

Table A-6

RJ-45 Pin

J1-3

J1-4

J1-5

J1-6

RJ-45 to Twinax Cable Pinouts (continued)

Signal

RX Shield

TX Tip

TX Ring

TX Shield

Description

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Direction

—>

—>

Appendix A Cabling Specifications

Twinax Pin

RX Shield

TX-1

TX-2

TX Shield

Figure A-4 RJ-45-to-RJ-45 Cable Assembly

J2

J1

Table A-7 lists the RJ-45-to-RJ-45 TE cable pinouts.

Table A-7 RJ-45-to-RJ-45 TE Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Shell/Braid

Twisted Pair #1

Twisted Pair #1

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Table A-8 lists the RJ-45-to-RJ-45 NT cable pinouts.

Table A-8 RJ-45-to-RJ-45 NT Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Shell/Braid

Twisted Pair #1

Twisted Pair #1

Twisted Pair #3

Twisted Pair #2

Twisted Pair #2

Twisted Pair #4

Direction

<—

<—

—>

—>

Direction

<—

<—

—>

—>

Signal

Ground

TX Tip

TX Ring

TX Shield

RX Tip

RX Ring

RX Shield

RJ-45 TE Pin

Shield

J2-1

J2-2

J2-3

J2-4

J2-5

J2-6

RJ-45 NT Pin

Shield

J2-4

J2-5

J2-6

J2-1

J2-2

J2-3

Note

Because the RJ-45-to-RJ-45 cable has polarity, the pinouts differ depending on which end of the cable you use.

A-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Appendix A Cabling Specifications

2-Port and 4-Port T1 or E1 Feature Card Cable and Port Pinouts

Table A-9 lists the RJ-45-to-RJ-45 T1 cable pinouts.

Table A-9 RJ-45-to-RJ-45 T1 Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Shell/Braid

Twisted Pair #1

Twisted Pair #1

Twisted Pair #2

Twisted Pair #2

Direction

<—

<—

—>

—>

RJ-45 T1 Pin

Shield

J2-1

J2-2

J2-4

J2-5

Figure A-5

J1

RJ-45 to Bare Wire Cable Assembly

Table A-10 lists the RJ-45 to bare wire cable pinouts.

Table A-10 RJ-45 to Bare Wire Cable Pinouts

RJ-45 Pin

Shield

J1-1

J1-2

J1-3

J1-4

J1-5

J1-6

Signal

Ground

RX Tip

RX Ring

RX Shield

TX Tip

TX Ring

TX Shield

Description

Braid

Twisted Pair #1

Twisted Pair #1

Twisted Pair #2

Twisted Pair #2

Direction

<—

<—

—>

—>

Bare

WIRE-1

WIRE-2

WIRE-3

WIRE-4

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-5

Appendix A Cabling Specifications

8-Port T1 or E1 Feature Card Cable and Port Pinouts

8-Port T1 or E1 Feature Card Cable and Port Pinouts

Figure A-6 shows a diagram of the 8-port T1 or E1 feature card cable assembly.

8-Port T1 or E1 Feature Card Cable Assembly Figure A-6

P4

P5

P6

P7

P0

P1

P2

P3

18

1

36

19

Table A-11 lists the 8-port T1 or E1 feature card cable pinouts.

8-Port T1 or E1 Feature Card Cable Pinouts Table A-11

Female RJ-45 (CAB-DFC-OCTAL-xMF)

From Signal

SHELL

J1-1

GROUND

RX_TIP

J1-2

J1-3

RX_RING

RX_TIP

J1-4

J1-5

RX_RING

RX_TIP

Note

SHELL/BRAID

Twisted pair #1

Port 7

Twisted pair #1

Port 6

Twisted pair #1

Direction

<------

<------

<------

<------

<------

Signal

GROUND

RX_TIP

RX_RING

RX_TIP

RX_RING

RX_TIP

J1-6

J1-7

J1-8

J1-9

J1-10

J1-11

J1-12

J1-13

RX_RING

RX_TIP

RX_RING

No Connect

No Connect

RX_TIP

RX_RING

RX_TIP

Port 5

Twisted pair #1

Port 4

Twisted pair #1

Port 3

Twisted pair #1

<------

<------

<------

<------

<------

<------

RX_RING

RX_TIP

RX_RING

No Connect

No Connect

RX_TIP

RX_RING

RX_TIP

J1-14

J1-15

J1-16

J1-17

RX_RING

RX_TIP

RX_RING

RX_TIP

Port 2

Twisted pair #1

Port 1

Twisted pair #1

<------

<------

<------

<------

RX_RING

RX_TIP

RX_RING

RX_TIP

J1-18 RX_RING Port 0 <-----RX_RING

J1 connector is male 36-position plug, J2–J9 connectors are female RJ-45 receptacles

To

SHELL

J9-1

J9-2

J8-1

J8-2

J7-1

J7-2

J6-1

J6-2

J5-1

J5-2

J4-1

J4-2

J3-1

J3-2

J2-1

J2-2

A-6

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Appendix A Cabling Specifications

8-Port T1 or E1 Feature Card Cable and Port Pinouts

Table A-11 8-Port T1 or E1 Feature Card Cable Pinouts (continued)

J1-22

J1-23

J1-24

J1-25

J1-26

J1-27

J1-28

J1-29

Female RJ-45 (CAB-DFC-OCTAL-xMF)

From

J1-19

Signal

TX_TIP

J1-20

J1-21

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

No Connect

No Connect

TX_TIP

Note

Twisted pair #2

Port 7

Twisted pair #2

Port 6

Twisted pair #2

Port 5

Twisted pair #2

Port 4

Direction

------>

------>

------>

------>

------>

------>

------>

------>

Signal

TX_TIP

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

No Connect

No Connect

TX_TIP Twisted pair #2 ------>

J1-30

J1-31

J1-32

J1-33

J1-34

J1-35

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

TX_TIP

Port 3

Twisted pair #2

Port 2

Twisted pair #2

Port 1

Twisted pair #2

------>

------>

------>

------>

------>

------>

TX_RING

TX_TIP

TX_RING

TX_TIP

TX_RING

TX_TIP

J1-36 TX_RING Port 0 ------> TX_RING

J1 connector is male 36-position plug, J2–J9 connectors are female RJ-45 receptacles

To

J9-4

J9-5

J8-4

J8-5

J7-4

J7-5

J6-4

J6-5

J5-4

J5-5

J4-4

J4-5

J3-4

J3-5

J2-4

J2-5

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-7

Appendix A Cabling Specifications

8-Port T1 or E1 Feature Card Cable and Port Pinouts

Attaching the 8-Port T1 or E1 Feature Card Interface Cable to a Bracket

(Optional)

To attach the 8-port T1 or E1 cable to a bracket:

Step 1

Place the molded RJ-45 end of the cable on the bracket with the RJ-45 ports facing you. Align the two holes on the molded RJ-45 end of the cable with the holes on the bracket. (See Figure A-7 .)

Figure A-7 Placing the Molded RJ-45 End of the Cable on the Bracket

A-8

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Appendix A Cabling Specifications

Step 2

8-Port T1 or E1 Feature Card Cable and Port Pinouts

You can align the molded RJ-45 ends of the cables in one of the following ways:

Place the molded RJ-45 ends of the cables next to each other. This placement creates space between the last molded RJ-45 end of the cable and the edge of the bracket adjacent to it. Route the cables through this space. (See Figure A-8 .)

Figure A-8 Routing Cables with Molded RJ-45 Ends of Cables Next to Each Other

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-9

Appendix A Cabling Specifications

8-Port T1 or E1 Feature Card Cable and Port Pinouts

Align the molded RJ-45 ends of the cables with an opening between the adjacent molded RJ-45 ends of the cable. Route the cables through the openings. (See Figure A-9 .)

Figure A-9 Routing Cables with Molded RJ-45 Ends of Cables Flush with Bracket Edges

A-10

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

Appendix A Cabling Specifications

Step 3

8-Port T1 or E1 Feature Card Cable and Port Pinouts

Secure the molded RJ-45 ends of the cables to the bracket with the provided flathead screws. (See

Figure A-10 .)

Note

To secure a single molded RJ-45 end of the cable, use the short flathead screws. To secure two

(stacked) molded RJ-45 ends of the cables, use the long flathead screws.

Figure A-10 Securing the Cable Bracket to the Rack

Step 4

Use the end screws on the bracket to secure the cable bracket to the rack. (See Figure A-10 .)

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-11

Appendix A Cabling Specifications

CT3 Feature Card Cable and Port Pinouts

Step 5

Insert the 36-pin cable connector into the 36-pin port on the 8-port T1 or E1 feature card. Tighten the captive screws on the 36-pin cable connector to secure the cable to the feature card. (See Figure A-11 .)

Figure A-11 Connecting the 36-Pin Cable Connector to an 8-Port T1 or E1 Feature Card

CT3 Feature Card Cable and Port Pinouts

Table A-12 lists the CT3 feature card port pinouts.

Table A-12 CT3 Feature Card Port Pinouts

1

2

Pin

Receiver port (on the left)

Description

Rx signal

Ground

Transmitter port

1

2

Tx signal

Ground

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-12 78-17406-01

Appendix A Cabling Specifications

Figure A-12 shows a diagram of the CT3 feature card cable assembly.

Figure A-12 CT3 Feature Card Cable Assembly

Bantam Jack Port Pinouts

Bantam Jack Port Pinouts

Table A-13 lists the bantam jack port pinouts.

Table A-13

Pin

1

2

Bantam Jack Port Pinouts

Description

Tip

Ring

78-17406-01

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

A-13

Bantam Jack Port Pinouts

Appendix A Cabling Specifications

A-14

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

I N D E X

Numerics

8-port T1 or E1 feature card attaching the interface cable to a bracket

A-8

interface cable pinouts

A-6

overview

4-1

port pinouts (table)

A-12

removing

4-2

A

attaching the 8-port T1 or E1 feature card interface cable to a bracket

A-8

B

bantam jack port monitoring feature cards

7-10

pinouts (table)

A-13

RX monitor port

7-10

TX monitor port

7-10

D

dial-only feature card installing

5-8

LEDs (table)

7-5

mixing with universal port feature card

7-6

online insertion and removal

5-3

overview

5-1

removing

5-3

restrictions

5-2

document organization

vii

drop and insert mode for the CT3 feature card

7-10

C

cabling specifications

A-1

carrier card installing

2-5

removing

2-3

caution symbol, meaning of

viii

chassis environment, monitoring

7-7

configuring input impedance for the E1 feature card

3-11

CT3 feature card drop and insert mode

7-10

installing

4-5

LEDs (table)

7-4

online insertion and removal

4-2

E

E1 feature card configuring input impedance

3-11

verifying input impedance

3-12

electricity, safety

1-2

environment, monitoring

7-7

environment status, checking

7-8

ESD wrist strap, safety

1-3

F

feature card online insertion and removal

2-2

overview

2-1

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01 IN-1

Index

G

ground connections, safety

1-2

N

network interfaces, troubleshooting

7-11

note symbol, meaning of

viii

I

input impedance configuring

3-11

verifying

3-12

installing carrier card

2-5

CT3 feature card

4-5

dial-only feature card

5-8

T1 or E1 feature card

3-9

universal port feature card

5-8

voice feature card

6-7

interface cable bracket, 8-port T1 or E1 feature card interface cable

A-8

O

OIR

CT3 feature card

4-2

dial-only feature card

5-3

feature card

2-2

T1 or E1 feature card

3-2

universal port feature card

5-3

voice feature card

6-3

online insertion and removal

See

OIR operating temperature

7-7

organization, document

vii

overview

CT3 feature card

4-1

dial-only feature card

5-1

feature cards

2-1

T1 or E1 feature card

3-1

universal port feature card

5-1

voice feature card

6-1

L

LEDs

CT3 feature card (table)

7-4

dial-only feature card (table)

7-5

location and description on feature cards

7-1

T1 or E1 feature card (table)

7-3

universal port feature card (table)

7-5

voice feature card (table)

7-5

M

mix of universal port and dial-only feature cards, troubleshooting

7-6

mix of voice feature cards with universal port and dial-only feature cards, troubleshooting

7-6

mix of WAN feature cards, troubleshooting

7-5

monitoring chassis environment

7-7

P

pinouts

8-port T1 or E1 feature card interface cable

A-6

bantam jack port

A-13

CT3 feature card port

A-12

RJ-45 to bare wire cable

A-5

RJ-45-to-BNC cable

A-3

RJ-45-to-DB-15 cable

A-2

RJ-45-to-DB-15 null modem cable

A-2

RJ-45-to-RJ-45 NT cable

A-4

RJ-45-to-RJ-45 T1 cable

A-5

RJ-45-to-RJ-45 TE cable

A-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

IN-2 78-17406-01

Index

R

RJ-45 to Twinax cable

A-3

removing carrier card

2-3

CT3 feature card

4-2

dial-only feature card

5-3

T1 or E1 feature card

3-3

universal port feature card

5-3

voice feature card

6-3

required tools and equipment

1-3

restrictions universal port and dial-only feature cards

5-2

voice feature card

6-2

RX MON bantam jack port

7-10

S

safety electricity

1-2

ESD wrist strap

1-3

ground connections

1-2

SPE firmware

5-10

symbols caution

viii

note

viii

timesaver

viii

tips

viii

LEDs (table)

7-3

online insertion and removal

3-2

overview

3-1

removing

3-3

RJ-45 to bare wire cable pinouts (table)

A-5

RJ-45-to-BNC cable pinouts (table)

A-3

RJ-45-to-DB-15 cable pinouts (table)

A-2

RJ-45-to-DB-15 null modem cable pinouts (table)

A-2

RJ-45-to-RJ-45 NT cable pinouts (table)

A-4

RJ-45-to-RJ-45 T1 cable pinouts (table)

A-5

RJ-45-to-RJ-45 TE cable pinouts (table)

A-4

RJ-45 to Twinax cable pinouts (table)

A-3

verifying input impedance

3-12

timesaver symbol, meaning of

viii

tips symbol, meaning of

viii

tools required

1-3

troubleshooting

7-1

displaying environment status

7-8

drop and insert mode for the CT3 feature card

7-10

LEDs

7-1

mix of universal port and dial-only feature cards

7-6

mix of voice feature cards with universal port and dial-only feature cards

7-6

mix of WAN feature cards

7-5

monitoring chassis environment

7-7

network interfaces

7-11

operating temperature

7-7

using bantam jack port

7-10

TX MON, bantam jack port

7-10

T

T1 or E1 feature card

8-port T1 or E1 feature card cable pinouts

A-6

attaching the 8-port T1 or E1 feature card interface cable to a bracket

A-8

cable assemblies

A-2

configuring input impedance

3-11

installing

3-9

U

universal port feature card installing

5-8

LEDs (table)

7-5

mixing with dial-only feature card

7-6

online insertion and removal

5-3

overview

5-1

removing

5-3

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01 IN-3

Index

restrictions

5-2

V

verifying input impedance on the E1 feature card

3-12

voice feature card installing

6-7

LEDs (table)

7-5

mixing with universal port and dial-only feature cards

7-6

online insertion and removal

6-3

overview

6-1

removing

6-3

restrictions

6-2

IN-4

Cisco AS5350XM and Cisco AS5400XM Universal Gateways Card Installation Guide

78-17406-01

advertisement

Related manuals

Download PDF

advertisement