COMMERCIAL
600 SERIES
OPERATION &
MAINTENANCE MANUAL
COMMERCIAL
SERIES
Model
610
612
614
616
632
633
632-20
633-20
660, 672, 682
661, 671, 681
663 673
664 674
670
680
690
*calculated R-Value
Door
Thickness R-Value*
1-3/8”
(34.9mm)
13.45
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
1-3/8”
(34.9mm)
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
13.45
Max. Door Size
Width
18’-2”
Height
16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
18’-2” 16’-0”
Steel
Extruded
End Cap
Extruded
End Cap
Extruded
End Cap
Extruded
End Cap
Extruded
End Cap
Extruded
End Cap
Extruded
End Cap
End Stile
Type
Extruded
End Cap
Extruded
End Cap
Steel
Steel
Steel
Steel
Steel
Inside
26 GA V-Groove
Woodgrain Steel
Section Skins
Outside
26 GA Flush
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
20 GA V-Groove
Smooth Steel
20 GA V-Groove
Smooth Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
26 GA Flush
Woodgrain Steel
26 GA V-Groove
Woodgrain Steel
20 GA Flush
Smooth Steel
20 GA V-Groove
Smooth Steel
20 GA Flush
Smooth Steel
20 GA V-Groove
Smooth Steel
26 GA Ribbed Short Panel
Woodgrain Steel
26 GA Recessed Short Panel
Woodgrain Steel
26 GA Recessed Long Panel
Woodgrain Steel
26 GA Ribbed Long Panel
Panel Woodgrain Steel
26 GA Ranch Panel
Woodgrain Steel
26 GA Raised Panel
Woodgrain Steel
26 GA Sculptured Panel
Woodgrain Steel
320 Sycamore Street Wauseon, OH 43567 www.haasdoor.com
Read Instructions Thoroughly
Before Starting Installation
Haas Door Commercial Instruction Manual
Commercial
Installation Manual
Supplimental Instructions Now Included:
American Tradition Hardware & Painting Instructions
CA & Full View Strut Installation
Commercial Bearing Plate Installation
Cylinder Lock Assembly
KCLA Drilling Templates
Lift Handle/Step Plate Instructions
Snap Latch Instructions
Vertical Lift Handle/Step Plate Instructions
Rev. 7/15 © 2015 Haas Door Company 1
Haas Door Commercial Instruction Manual
OPENING PREPARATION
Note : All framing materials must be provided by building contractor or installer.
Figure 2
W
Some large doors may require additional pad or pads located off center to accommodate auxiliary bearings.
S
B
W
S
All vertical jambs and pads regardless of type, must extend to top of headroom requirement.
Steel
Channel
W W S S
2 X 6
Wood Jambs
Section “W”
Opening Width
Interior Elevation
3” Min.
Steel Jambs
Section “S”
STEP 1 INSTALLATION OF DOOR
Check the size of door to be sure it is the same size as opening. Inspect the track and determine if you have reverse angle or bracket mount tracks. Note: bracket mount has individual j-brackets to attach track to jamb, reverse angle has a continuous angle to attach track to jamb. Note: if door is supplied with reverse angle. The door should be 2” wider than opening.
Bottom
Section
J
Center
Hinge
G
End Hinge see Figure 6 on page 4 for correct hinge numbers
Center Stile
Weatherstrip
Roller
Figure 3
H
Bottom Bracket
Cable
Drill a 3 /16” diameter hole for this screw
STEP 2
Attach hardware to bottom section with 1/4” x 3/4” hex head sheet metal screws (see Figure 3). If door requires struts, see
Figure 8 on page 4.
2 © 2015 Haas Door Company Rev. 7/15
Haas Door Commercial Instruction Manual
INSTALLATION OF VERTICAL TRACKS
STEP 3
Position bottom section in center of the opening, allowing equal distance from each side of the opening.
STEP 4
Position left hand track over rollers as shown in Figure 4. Space track 1/2” from door as shown.
Before attaching vertical track angle or brackets to jambs it must be plumb and parallel to door and raised to match leveling of bottom door section.
Attach vertical track angles to jambs by welding or by using 1/4” self drilling screws on steel jambs or 5/16" x 1 1/ 2” hex head lag screws on wood jambs. If mounting directly to masonry, anchors are not supplied.
Repeat above step for right hand track. (Note: Both tracks must be parallel for proper operation)
Insert rollers into end hinges.
Hook rollers into vertical track and swing end hinges onto door section as shown at left.
Secure with fasteners provided.
STEP 5
Place #2 section on top of bottom section. Note: if door is supplied with cylinder lock, use section with lock holes punched or drilled in it (see Step 19 on page 8).
Attach hinges and rollers as shown in Figure 5. See hinge schedule Figure 6 on page 4 for correct placement of numbered hinges. If inside lock is supplied, see Figure 7.
Rev. 7/15 © 2015 Haas Door Company 3
STEP 6
Haas Door Commercial Instruction Manual
HINGE SCHEDULE
Complete the remainder of the sections at this time. Top door section should only be installed after horizontal track or full vertical track has been installed.
Note: if door is supplied with full view aluminum section(s), attach hinges with 1/4” self drilling screws provided.
STEP 7 SLIDE BOLT LOCK
The inside lock is installed on the end stile of the second section so the slide bolt rests against the top of one of the rectangular engaging slots in the vertical track (see Figure 7).
If door is supplied with cylinder lock, see page 8.
STEP 8 STRUT INSTALLATION
All struts except top section strut are attached with tech screws below hinges as shown in Figure 8. Top section strut is located directly above the top roller brackets, secured at the ends with tech screws. Secure all struts to center stiles through existing holes utilizing tech screws.
Note: Doors over 14’-2” wide require one strut per section.
STEP 9 STANDARD LIFT TRACK
Attach bearing brackets to the horizontal angles with 3/8” x
3/4” bolts & nuts. Form rope loops to a convenient overhead structural member & insert horizontal tracks through them, then attach bottom of the curved portions of track to the top of the vertical tracks at the splice brackets with 1/4” x 5/8” truss head machine screws & nuts. Head of machine screws should be to inside of the track (see Figure 9). Using a level, strike a plumb line from the inside of the splice bracket to the inside of the horizontal angle on each side. Place outside edges of bearing brackets against the plumb lines and attach brackets securely to the wall (see Figure 9).
4 © 2015 Haas Door Company Rev. 7/15
Haas Door Commercial Instruction Manual
STEP 9a HI-LIFT TRACK
Connect vertical hi-lift track to top of existing vertical track with 1/4”x 5/8” truss head machine screws. Set track plumb and fasten to jamb in the same manner as the vertical track previously installed in Step 4. Attach bearing brackets to the horizontal angles with 3/8” x 3/4” bolts & nuts. Form rope loops to a convenient overhead structural member and insert horizontal tracks through them, then attach bottom of the curved portions of track to the top of the vertical tracks at the splice brackets with 1/4” x 5/8” truss head machine screws and nuts. Head of machine srews should be to inside of the track (see Figure 9a). Using a level, strike a plumb line from the inside ot the splice bracket to the inside of the horizontal angle on each side. Place outside edges of bearing brackets against the plumb lines and attach brackets securely to the wall
(see Figure 9a).
STEP 9b VERTICAL LIFT TRACK
Place upper vertical track on top of lower vertical track.
Plumb track and attach to wall in same manner as lower vertical tracks. Heads of machine screws should be to inside of the tracks as shown in Figure 9b. (Jamb fasteners must be installed with no more than 48” between each fastener.)
Now set bearing brackets against the plumb lines and attach brackets securely to the track and wall.
STEP 10
HORIZONTAL TRACK SUPPORT
Replace temporary support hangers with steel support angle
(not supplied). Install sway braces only after checking the horizontal track with a tape measure or spacing bar to verify that they are parallel. Important: steel support or other means must be strong enough to support full door weight and must be attached to a structurally sound member.
Note: a center horizontal track support is required for doors larger than 12’-1” in height (see Figure 1 Item A on page 1).
STEP 11 TOP BRACKETS
Place top section in position. With rollers inserted in the sleeves of top roller brackets, bolt brackets to section through holes provided, utilizing self-tapping screws. Adjust bracket slide so top section is perfectly vertical and tighten adjusting bolt securely. Attach top leaves of hinges from the preceding section. Check tracks for proper clearance and permanently secure all fasteners.
Rev. 7/15 © 2015 Haas Door Company 5
Haas Door Commercial Instruction Manual
WARNING:
Installing torsion springs can be a dangerous procedure and should only be performed by qualified door service personnel.
Do not attempt installation without proper tools and until reading and understanding the following instructions.
STEP 12 COUNTERBALANCE INSTALLATION
Determine what type of spring assembly you have as shown in figures 12, 13, 14 or 15.
STEP 13
Place the center support bracket and the bearing on the axles as shown in Figure 16 (bearing sits inside spring fitting). Bolt spring fitting(s) to center support bracket (see Figure 16 or 17) using 3/8” dia. x 1 1/2” hex head bolts. Slide a cable drum on both ends of shaft. Be sure correct hand drum is used (see Figures 12 thru 15). Slide bearing on each shaft end if not already bolted to track.
6 © 2015 Haas Door Company Rev. 7/15
Haas Door Commercial Instruction Manual
STEP 14
Raise the shaft assembly over the door. If 2 piece shaft with coupling is supplied, raise half the total shaft at a time. Rest the end(s) of shaft on the horizontal track angle.
See Figure 19 For coupling installation.
STEP 15
Locate and attach spring bearing plates/center support bracket to mountlng pads (not supplied). See Figure 2 for wood or steel frame (jambs) . Mount spring brackets to structural member of building of sufficient size to withstand spring(s) torque.
When mounting springs on pads, keep in mind that springs grow in length when wound. Allow at least 5” space between spring fitting and cable drum. If mounting the center support bracket to wood, use (2) 5/16” x 1 5/8” long hex head lags for each bracket. For steel jambs use (2) 3/8” x 1 1/2” hex head bolts. If mountlng directly to concrete use (2) 5/16” dia thru bolts or threaded rods (not supplied).
STEP 16 ATTACHING THE CABLES
Thread each cable between the axle and wall. Then insert each cable into the entry slot of each drum. Wind the excess cable on the drum, then slide the drum against the bearing plate and tighten the two set screws securing the drum to the shaft.
Clamp a set of locking pliers with the jaws locked onto the shaft and the other end against the wall so that cable tension 0n the drum is taut (no slack) and the shaft locked. Secure the remaining drum making sure both cables have equal tension and are taut (see Figure 20). If axle is a solid shaft use a 1/4” key for both drums.
STEP #17
Before going to Step 18. Be sure door is in locked position. If no lock is supplied, place a clamp in both tracks of door directly above a roller to make sure door can not be raised at this tlme.
STEP # 18 WINDING SPRING
(see Figure 21)
Note: garage door springs can cause serious injury if not handled properly. Before winding the springs, make sure the lock is engaged in the “locked” position. This will prevent the door from raising up by itself in the event the springs are over wound or are too strong . Use two cold rolled steel rods approximately 18” long and the same diameter as the holes in the winding cones (winding rods not furnished) 1/2” dia. for 1 3/4” & 2 5/8” springs and 5/8” dia. for larger springs. Do not use undersized rods or other tools to wind springs. For your safety, position yourself on a sturdy ladder so that winding cone is either to your right or to your left. Never stand directly in front of winding cones or winding bars. With one hand, insert one winding rod all the way into the hole of the winding cone and wind the spring up one-quarter turn. With your other hand, insert the second winding bar into the next hole, remove the upper winding bar and then take another one-quarter turn. Proceed in this manner until you have made all the required number of turns. The number of turns are indicated on the spring tag attached to the spring assembly. For example, if the tag says “wind spring 7 turns, 7 x 4 = 28 one-quarter turns are required to balance.
Note: each complete turn will cause the chalk line to make one spiral. After the requred number of 1/4 turns have been made, tighten both set screws in the winding cone to secure it to the shaft before removing the winding bars. Repeat this procedure for each spring, then locking pliers can be removed. Attach one red warning label to spring.
Rev. 7/15 © 2015 Haas Door Company 7
Haas Door Commercial Instruction Manual
STEP 19 CYLINDER LOCK INSTALLATION
If lock cylinder is supplied, install in lock section as shown in the exploded view (see Figure 22).
STEP #20 LIFT HANDLES
Install lift handle(s) on bottom section with 1/4” - 20 nuts and bolts supplied (as shown in fig. # 23).
MAINTENANCE & CAUTIONS
Recommended Service: lubricate rollers with a light oil as required. Check and tighten all nuts, bolts and screws annually.
(This may be required more frequently for high usage doors.)
Haas Door recommends servicing any part of the counterbalance system including springs, drums cables, bearing brackets, and bottom corner brackets where cable is attached be performed by qualified door service personnel only (see notice below).
Important Safety Notice:
Operate door only when properly adjusted and free of obstructions. Door is under extreme spring tension. Repairs and adjustments, especially to cables and spring assembly, can be hazardous and should be performed by qualifled door service personnel only.
Do not permit children to play with garage door or electric controls.
If door is now, or later becomes, electrically operated, pull down rope must be removed.
Avoid standing in open doorway or walking thru doorway while electrically operated door is moving.
Should door become hard to operate or completely inoperative, it is recommended that a qualified door agency be contacted.
The notice above has been approved and recommended by the National Association of Garage Door Manufacturers (NAGDM).
8 © 2015 Haas Door Company Rev. 7/15
Haas Door Company warrants its Commercial 800, 2000, 700 and 600 series steel garage door sections to be free from delamination or rustthrough for a period of 10 years to the original purchaser of the building where the door sections are installed. All other components are warranted to be free from defects in workmanship and material for a period of one (1) year from date of installation.
This ten year Warranty applies only to steel garage door sections manufactured by Haas Door Company and components manufactured or supplied by Haas Door Company. The warranty excludes: (1) Sections and/or component parts which have been damaged due to misuse; (2) Sections and/or components which have been improperly installed, maintained or operated; (3) Sections and/or components that have been damaged due to accident; (4) Sections and/or components that have been damaged due to exposure to salt environments including coastal areas, corrosive fumes/chemicals, alkaline cleaning agents, condensation or fire; (5) Repair and/or replacement labor charges, including travel cost; (6) Cool Black color on 700, 2000 and 800 series; (7)
Damages resulting from other causes beyond the manufacturers control.
In the event any defect is claimed during the warranty periods, a claim in writing must be submitted to Haas
Door Company, directed through an authorized Haas Door Company dealer or installer. This claim must be submitted within fifteen (15) days of the discovery of the suspected defect. The door and all components must be available for inspection by an authorized Haas Door Company representative. Upon verification of a manufacturing defect, Haas Door Company will provide repair or replacement part(s) at its option.
THE MANUFACTURER SHALL NOT BE RESPONSIBLE FOR ANY INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF ANY BREACH OF THIS EXPRESS LIMITED WARRANTY,
including but not limited to any damage to buildings, other property or for any injuries or damages sustained by any person whomsoever, or the recovery of any direct or indirect costs such as shipping, travel, lost time, installation labor charges, paint or painting, cleaning, repair, or other building materials.
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THE PURCHASE;
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF.
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN, AND ANY REMEDIES WHICH BUT FOR THE
WARRANTY CONTAINED HEREIN MIGHT ARISE BY IMPLICATION OR OPERATION OF LAW, IS
HEREBY EXCLUDED AND DISCLAIMED, INCLUDING THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE.
- - - - - T H I S W A R R A N T Y I S N O T T R A N S F E R A B L E - - - - -
2015 Haas Door Company
320 Sycamore St. Wauseon, OH 43567
Effective: June 4, 2012
Revised: October 19, 2015
