Onkyo HT-RC440 Owner's Manual

Add to My manuals
120 Pages

advertisement

Onkyo HT-RC440 Owner's Manual | Manualzz

AV RECEIVER

HT-RC440

Instruction Manual

Contents

Safety Information and Introduction ............2

Table of Contents ...........................................5

Connections .................................................11

Turning On & Basic Operations..................18

Advanced Operations ..................................37

Controlling Other Components...................51

Appendix .......................................................57

Internet Radio Guide

Remote Control Codes

E n

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPARATUS TO RAIN OR

MOISTURE.

CAUTION:

TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED

SERVICE PERSONNEL.

WARNING

RISK OF ELECTRIC SHOCK

DO NOT OPEN

AVIS

RISQUE DE CHOC ELECTRIQUE

NE PAS OUVRIR

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Important Safety Instructions

1.

Read these instructions.

2.

Keep these instructions.

3.

Heed all warnings.

4.

Follow all instructions.

5.

Do not use this apparatus near water.

6.

Clean only with dry cloth.

7.

Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.

Only use attachments/accessories specified by the manufacturer.

12.

Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.

When a cart is used, use

PORTABLE CART WARNING caution when moving the cart/apparatus combination to

S3125A avoid injury from tip-over.

13.

Unplug this apparatus during lightning storms or when unused for long periods of time.

14.

Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

15.

Damage Requiring Service

Unplug the apparatus from the wall outlet and refer servicing to qualified service personnel under the following conditions:

A.

When the power-supply cord or plug is damaged,

B.

If liquid has been spilled, or objects have fallen into the apparatus,

C.

If the apparatus has been exposed to rain or water,

Safety Information and Introduction

D.

If the apparatus does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the apparatus to its normal operation,

E.

If the apparatus has been dropped or damaged in any way, and

F.

When the apparatus exhibits a distinct change in performance this indicates a need for service.

16.

Object and Liquid Entry

Never push objects of any kind into the apparatus through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock.

The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases shall be placed on the apparatus.

Don’t put candles or other burning objects on top of this unit.

17.

Batteries

Always consider the environmental issues and follow local regulations when disposing of batteries.

18.

If you install the apparatus in a built-in installation, such as a bookcase or rack, ensure that there is adequate ventilation.

Leave 20 cm (8") of free space at the top and sides and

10 cm (4") at the rear. The rear edge of the shelf or board above the apparatus shall be set 10 cm (4") away from the rear panel or wall, creating a flue-like gap for warm air to escape.

En-2

Precautions

1. Recording Copyright

—Unless it’s for personal use only, recording copyrighted material is illegal without the permission of the copyright holder.

2. AC Fuse

—The AC fuse inside the unit is not userserviceable. If you cannot turn on the unit, contact your

Onkyo dealer.

3. Care

—Occasionally you should dust the unit all over with a soft cloth. For stubborn stains, use a soft cloth dampened with a weak solution of mild detergent and water. Dry the unit immediately afterwards with a clean cloth. Don’t use abrasive cloths, thinners, alcohol, or other chemical solvents, because they may damage the finish or remove the panel lettering.

4. Power

WARNING

BEFORE PLUGGING IN THE UNIT FOR THE

FIRST TIME, READ THE FOLLOWING SECTION

CAREFULLY.

AC outlet voltages vary from country to country. Make sure that the voltage in your area meets the voltage requirements printed on the unit’s rear panel (e.g., AC

230 V, 50 Hz or AC 120 V, 60 Hz).

The power cord plug is used to disconnect this unit from the AC power source. Make sure that the plug is readily operable (easily accessible) at all times.

For models with [

POWER

] button, or with both

[

POWER

] and [

ON/STANDBY

] buttons:

Pressing the [

POWER

] button to select OFF mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

For models with [

ON/STANDBY

] button only:

Pressing the [

ON/STANDBY

] button to select

Standby mode does not fully disconnect from the mains. If you do not intend to use the unit for an extended period, remove the power cord from the AC outlet.

5. Preventing Hearing Loss

Caution

Excessive sound pressure from earphones and headphones can cause hearing loss.

6. Batteries and Heat Exposure

Warning

Batteries (battery pack or batteries installed) shall not be exposed to excessive heat as sunshine, fire or the like.

7. Never Touch this Unit with Wet Hands

—Never handle this unit or its power cord while your hands are wet or damp. If water or any other liquid gets inside this unit, have it checked by your Onkyo dealer.

8. Handling Notes

• If you need to transport this unit, use the original packaging to pack it how it was when you originally bought it.

• Do not leave rubber or plastic items on this unit for a long time, because they may leave marks on the case.

• This unit’s top and rear panels may get warm after prolonged use. This is normal.

• If you do not use this unit for a long time, it may not work properly the next time you turn it on, so be sure to use it occasionally.

For U.S. models

FCC Information for User

CAUTION:

The user changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Safety Information and Introduction

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

For Canadian Models

NOTE:

THIS CLASS B DIGITAL APPARATUS

COMPLIES WITH CANADIAN ICES-003.

For models having a power cord with a polarized plug:

CAUTION:

TO PREVENT ELECTRIC SHOCK,

MATCH WIDE BLADE OF PLUG TO WIDE SLOT,

FULLY INSERT.

Modèle pour les Canadien

REMARQUE:

CET APPAREIL NUMÉRIQUE DE LA

CLASSE B EST CONFORME À LA NORME NMB-003

DU CANADA.

Sur les modèles dont la fiche est polarisée:

ATTENTION:

POUR ÉVITER LES CHOCS

ÉLECTRIQUES, INTRODUIRE LA LAME LA PLUS

LARGE DE LA FICHE DANS LA BORNE

CORRESPONDANTE DE LA PRISE ET POUSSER

JUSQU’AU FOND.

En-3

Supplied Accessories

Make sure you have the following accessories:

Indoor FM antenna (

page 17 )

AM loop antenna (

page 17 )

Speaker cable labels (

page 11 )

Remote controller (RC-834M) and two batteries (AA/R6)

Quick Start Guide

* In catalogs and on packaging, the letter at the end of the product name indicates the color. Specifications and operations are the same regardless of color.

Installing the batteries

Batteries (AA/R6)

Note

• If the remote controller doesn’t work reliably, try replacing the batteries.

• Don’t mix new and old batteries or different types of batteries.

• If you intend not to use the remote controller for a long time, remove the batteries to prevent damage from leakage or corrosion.

• Remove expired batteries as soon as possible to prevent damage from leakage or corrosion.

Safety Information and Introduction

Aiming the remote controller

To use the remote controller, point it at the AV receiver’s remote control sensor, as shown below.

Remote control sensor

AV receiver

Approx. 16 ft. (5 m)

Thank you for purchasing an Onkyo AV Receiver.

Please read this manual thoroughly before making connections and plugging in the unit.

Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver.

Please retain this manual for future reference.

En-4

Table of Contents

Safety Information and Introduction

Important Safety Instructions ......................................2

Precautions ...................................................................3

Supplied Accessories...................................................4

Table of Contents..........................................................5

Features .........................................................................6

Front & Rear Panels......................................................7

Front Panel..................................................................7

Display ........................................................................8

Rear Panel ..................................................................9

Remote Controller.......................................................10

Controlling the AV Receiver ......................................10

Connections

Connecting the AV Receiver......................................11

Connecting Your Speakers .......................................11

About AV Connections ..............................................13

Connecting Components with HDMI .........................14

Connecting Your Components ..................................15

Connecting Onkyo RI Components...........................16

Connecting the Antennas..........................................17

Connecting the Power Cord ......................................17

Turning On & Basic Operations

Turning On/Off the AV Receiver ................................18

Turning On ................................................................18

Turning Off ................................................................18

Playback ......................................................................19

Playing the Connected Component ..........................19

Controlling Contents of USB or Network Devices .....20

Understanding Icons on the Display .........................21

Playing an iPod/iPhone via USB ...............................21

Playing a USB Device ...............................................22

Listening to vTuner Internet Radio ............................22

Registering Other Internet Radio ..............................23

Playing Music Files on a Server................................24

Remote Playback ......................................................25

Listening to AM/FM Radio.........................................26

Using Basic Functions ............................................... 28

Using the Listening Modes ....................................... 28

Using the Home Menu .............................................. 33

Using the Sleep Timer .............................................. 34

Setting the Display Brightness.................................. 34

Displaying Source Information.................................. 34

Changing the Input Display....................................... 35

Using the Music Optimizer ........................................ 35

Muting the AV Receiver ............................................ 35

Using Headphones ................................................... 36

Advanced Operations

On-screen Setup ......................................................... 37

Using the Quick Setup .............................................. 37

Using the Audio Settings of Quick Setup.................. 38

Using the Setup Menu (HOME) ................................ 39

About the HYBRID STANDBY indicator ................... 40

Setup menu items..................................................... 40

HDMI Input................................................................ 41

Component (Component Video Input) ...................... 41

Digital Audio (Digital Audio Input) ............................. 42

Sp Config (Speaker Configuration)........................... 42

Sp Distance (Speaker Distance)............................... 43

Level Cal (Level Calibration)..................................... 43

Audio Adjust.............................................................. 44

Source Setup ............................................................ 45

Hardware .................................................................. 46

HDMI Setup .............................................................. 47

Network Setup .......................................................... 48

Zone 2 .......................................................................... 50

Making Zone 2 Connections ..................................... 50

Controlling Zone 2 Components ............................... 50

Controlling Other Components

iPod/iPhone Playback via Onkyo Dock .................... 51

Using the Onkyo Dock .............................................. 51

Controlling Your iPod/iPhone.................................... 52

Controlling Other Components ................................. 53

Preprogrammed Remote Control Codes .................. 53

Entering Remote Control Codes............................... 53

Remapping Colored Buttons..................................... 53

Remote Control Codes for Onkyo Components Connected via RI.............. 54

Resetting the REMOTE MODE Buttons ................... 54

Resetting the Remote Controller .............................. 54

Controlling Other Components ................................. 54

Safety Information and Introduction

Appendix

Troubleshooting ......................................................... 57

Firmware Update ........................................................ 62

Connection Tips and Video Signal Path .................. 66

Using an RIHD-compatible TV, Player, or Recorder .............................................................. 67

About HDMI................................................................. 69

Network/USB Features............................................... 70

License and Trademark Information ........................ 73

Specifications ............................................................. 74

To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT , press

8

ON/STANDBY

(

page 57

).

En-5

Features

Amplifier

• 80 Watts/Channel @ 8 ohms (FTC)

• Optimum Gain Volume Circuitry

• H.C.P.S. (High Current Power Supply) Massive High

Power Transformer

Processing

• HDMI (Audio Return Channel, 3D, DeepColor, x.v.Color, Lip Sync, DTS-HD Master Audio, DTS-HD

High Resolution Audio, Dolby TrueHD, Dolby Digital

Plus, DSD and Multi-CH PCM)

• Non-Scaling Configuration

• A-Form Listening Mode Memory

• Direct Mode

• Music Optimizer for Compressed Digital Music files

• 192 kHz/24-bit D/A Converters

• Powerful and Highly Accurate 32-bit Processing DSP

• Jitter Cleaning Circuit Technology

Connections

• 6 HDMI Inputs and 1 Output

• Onkyo p

for System Control

• 4 Digital Inputs (2 Optical/2 Coaxial)

• Component Video Switching (2 Inputs/1 Output)

• Banana Plug-Compatible Speaker Posts

• Internet Radio Connectivity

• Network Capability for Streaming Audio Files

• Front-Panel USB Input for Memory Devices and iPod ® /iPhone ® models

Safety Information and Introduction

Miscellaneous

• 40 FM/AM Presets

• Crossover Adjustment

(40/50/60/70/80/90/100/120/150/200 Hz)

• A/V Sync Control Function (up to 400 ms)

• Auto Standby Function

• On-Screen Display via HDMI

• Preprogrammed u

-Compatible Remote

En-6

Front & Rear Panels

Front Panel

a  b  c  d  e  f g  h i j k  l  m 

Safety Information and Introduction

n  o  p 

For detailed information, see the pages in parentheses.

a 8

ON/STANDBY

button (

18

)

b

ZONE 2

,

OFF

buttons (

50

)

c

Remote control sensor ( 4 )

d

Display ( 8 )

e

LISTENING MODE buttons ( 28 )

f

DIMMER button ( 34 )

g

MEMORY button ( 27 )

h

TUNING MODE button ( 26 )

i

DISPLAY

button (

34

)

j

SETUP

button (

39

)

q  r  s  t 

k

TUNING

q

/

w

,

PRESET

e

/

r

(

26

), cursor and

ENTER buttons

l

RETURN button

m

MASTER VOLUME control ( 19 )

n

MUSIC OPTIMIZER button and indicator ( 35 , 38 )

o

PHONES jack ( 36 )

p

TONE and Tone Level buttons ( 38 )

q

Input selector buttons (

19

)

r

AUX INPUT AUDIO/VIDEO jacks (

15

)

s

USB port ( 15 )

t

HYBRID STANDBY indicator ( 40 )

En-7

s

Display

a b c d  e  f  g h 

Safety Information and Introduction

i  j  k  l  i  d 

For detailed information, see the pages in parentheses.

a

Z2 (Zone 2) indicator ( 50 )

b

3D indicator

This lights when a 3D input signal is detected.

c

Headphone indicator ( 36 )

d 1

,

3

and cursor indicators ( 21 )

e

Listening mode and format indicators ( 28 )

f

M.Opt indicator ( 35 , 38 )

g

Tuning indicators

AUTO indicator ( 26 )

TUNED indicator ( 26 )

FM STEREO indicator ( 26 )

h

MUTING indicator (

35

)

m  i

Input indicators ( 66 )

HDMI indicator (

47

)

DIGITAL indicator

j

ARC indicator ( 48 )

k

USB indicator (

21

,

22

)

l

NET indicator ( 22 to 25 , 49 )

m

Message area

n

SLEEP indicator ( 34 )

o

Channel/Unit indicators ch indicator

Hz indicator m/ft indicator dB indicator

p

ASb indicator (

46

)

En-8

n  o  p 

Rear Panel

a  b  c  d  e  f  g 

Safety Information and Introduction

h  i  j k  l 

a

DIGITAL IN COAXIAL and OPTICAL jacks

b

COMPONENT VIDEO IN and OUT jacks

c

ETHERNET port

d

FM ANTENNA jack and AM ANTENNA terminal

e

HDMI IN

and

OUT

jacks

f

SPEAKERS

terminals

( CENTER , FRONT , SURROUND )

g

Power cord

h u 

REMOTE CONTROL

jack

i

Composite video and analog audio jacks

(

BD/DVD IN

,

CBL/SAT IN

,

GAME IN

,

PC IN

,

TV/CD IN )

j

ZONE 2 LINE OUT jacks

k

SUBWOOFER PRE OUT jack

l

MONITOR OUT V jack

See “Connecting the AV Receiver” for connection

(

pages 11

to

17

).

En-9

Remote Controller

Controlling the AV Receiver

a b

*1 a c d g h c i d j k

To control the AV receiver, press RECEIVER to select

Receiver mode.

You can also use the remote controller to control

Onkyo Blu-ray Disc/DVD player, CD player, and other components.

See “Entering Remote Control Codes” for more details (

page 53 ).

For detailed information, see the pages in parentheses.

a 8

RECEIVER button ( 18 )

b

REMOTE MODE/INPUT SELECTOR buttons ( 19 )

c q

/

w

/

e

/

r

and ENTER buttons

d

Q SETUP button ( 37 )

e

Listening Mode buttons ( 28 )

f

DIMMER

button (

34

)

g

MUTING

button (

35

)

h

DISPLAY button ( 34 )

i

VOL

q

/

w

button ( 19 )

j

RETURN button

k

HOME button ( 33 )

l

SLEEP button ( 34 )

Safety Information and Introduction

Controlling the tuner

To control the AV receiver’s tuner, press

AM

or

FM

(or

RECEIVER

).

a q

/

w

buttons ( 26 )

b

D.TUN

button ( 26 )

c

DISPLAY button

d

CH +/– button ( 27 )

e

Number buttons ( 26 )

*1 To control a component, you must first enter the remote control code.

See “Entering Remote Control Codes” for more details

(

page 53

).

e b f e l

En-10

Connecting the AV

Receiver

Connecting Your Speakers

Connecting the Speaker Cables

The following illustration shows how to connect the speakers to each pair of terminals.

Screw-type speaker terminals

Strip 1/2" to 5/8" (12 to 15 mm) of insulation from the ends of the speaker cables, and twist the bare wires tightly, as shown.

1/2" to 5/8" (12 to 15 mm)

Banana Plugs

• If you are using banana plugs, tighten the speaker terminal before inserting the banana plug.

• Do not insert the speaker code directly into the center hole of the speaker terminal.

Surround right

Surround left

Front right Front left Center

Connections

Speaker Configuration

The following table indicates the channels you should use depending on the number of speakers that you have.

No matter how many speakers you use, a powered subwoofer is recommended for a really powerful and solid bass.

To get the best from your surround sound system, you need to set the speaker settings manually (

page 42

).

Number of speakers

Front speakers

Center speaker

Surround speakers

2

3

4

5

Attaching the Speaker Cable Labels

The speaker terminals are color-coded for identification purpose.

Speaker

Front left

Front right

Center

Surround left

Surround right

Color

White

Red

Green

Blue

Gray

The supplied speaker cable labels are also color-coded and you should attach them to the positive (+) side of each speaker cable in accordance with the table above. Then all you need to do is to match the color of each label to the corresponding speaker terminal.

En-11

Using a Powered Subwoofer

Connections

Speaker Connection Precautions

Read the following before connecting your speakers:

• You can connect speakers with an impedance of between

6 and 16 ohms. If you use speakers with a lower impedance, and use the amplifier at high volume levels for a long period of time, the built-in amp protection circuit may be activated.

• Disconnect the power cord from the wall outlet before making any connections.

• Read the instructions supplied with your speakers.

• Pay close attention to speaker wiring polarity. In other words, connect positive (+) terminals only to positive (+) terminals, and negative (–) terminals only to negative (–) terminals. If you get them the wrong way around, the sound will be out of phase and will sound unnatural.

• Unnecessarily long, or very thin speaker cables may affect the sound quality and should be avoided.

• Be careful not to short the positive and negative wires.

Doing so may damage the AV receiver.

• Make sure the metal core of the wire does not have contact with the AV receiver’s rear panel. Doing so may damage the AV receiver.

• Don’t connect more than one cable to each speaker terminal. Doing so may damage the AV receiver.

• Don’t connect one speaker to several terminals.

LINE INPUT

Powered subwoofer

LINE INPUT

Corner position

1/3 of wall position

To find the best position for your subwoofer, while playing a movie or some music with good bass, experiment by placing your subwoofer at various positions within the room, and choose the one that provides the most satisfying results.

Tip

• If your subwoofer is unpowered and you’re using an external amplifier, connect the subwoofer pre out jack to an input on the amplifier.

En-12

About AV Connections

Connecting AV components

a

HDMI cable

TV, projector, etc.

*1

: Video & Audio

AV receiver

• Push plugs in all the way to make good connections (loose connections can cause noise or malfunctions).

• To prevent interference, keep audio and video cables away from power cords and speaker cables.

AV Cables and Jacks

HDMI

Right!

Wrong!

HDMI connections can carry digital video and audio.

Other cables

TV, projector, etc.

Blu-ray Disc/

DVD player

: Video

Game console

AV receiver

: Audio

Blu-ray Disc/

DVD player

Game console

*1 If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the

HDMI cable to the AV receiver.

• Before making any AV connections, read the manuals supplied with your AV components.

• Don’t connect the power cord until you’ve completed and double-checked all AV connections.

Y

P

B

P

R

Component video

Component video separates the luminance (Y) and color difference signals (P

B

, P

R

), providing the best picture quality (some TV manufacturers label their component video sockets slightly differently).

Green

Blue

Red

Composite video

Composite video is commonly used on TVs, DVDs, and other video equipment.

Yellow

Connections

Optical digital audio

Optical digital connections allow you to enjoy digital sound such as PCM

*2

, Dolby Digital or DTS. The audio quality is the same as coaxial.

Coaxial digital audio

Coaxial digital connections allow you to enjoy digital sound such as PCM *2 , Dolby Digital or DTS. The audio quality is the same as optical.

Orange

Analog audio (RCA)

Analog audio connections (RCA) carry analog audio.

White

Red

*2 Available sampling rate for PCM input signal (stereo/mono) is

32/44.1/48/88.2/96 kHz. In case of an HDMI connection,

176.4/192 kHz is also available.

Note

• The AV receiver does not support SCART plugs.

• The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed. Push plugs in all the way.

Caution

• To prevent shutter damage, hold the optical plug straight when inserting and removing.

En-13

Connections

Connecting Components with HDMI

Satellite/cable set-top box, etc.

Personal computer

TV, projector, etc.

Game console

* If your TV doesn’t support Audio Return Channel (ARC), you need to connect an optical digital cable together with the HDMI cable to the AV receiver.

* When listening to an HDMI component through the AV receiver, set the HDMI component so that its video can be seen on the TV screen (on the TV, select the input of the HDMI component connected to the AV receiver). If the TV power is off or the TV is set to another input source, this may result in no sound from the AV receiver or the sound may be cut off.

Connect your components to the appropriate jacks. The default input assignments are shown below.

: Assignment can be changed (

page 41

).

Jack

HDMI IN1

HDMI IN2

HDMI IN3

HDMI IN4

HDMI IN5

Components

Blu-ray Disc/DVD player

Satellite/cable set-top box, etc.

Game console

Personal computer

Other components

HDMI IN6 Other components

HDMI OUT TV, projector, etc.

Blu-ray Disc/DVD player

See also:

• “Connection Tips and Video Signal Path” (

page 66

)

• “Using an RIHD-compatible TV, Player, or Recorder”

(

page 67

)

• “About HDMI” (

page 69

)

Tip

• To listen to the audio of a component connected via HDMI through your TV’s speakers, enable “

HDMI Through

(

page 47

) and set the AV receiver to standby mode.

Note

• In the case of Blu-ray Disc/DVD players, if no sound is output despite following the above-mentioned procedure, set your Bluray Disc/DVD player’s HDMI audio settings to PCM.

Audio Return Channel (ARC) function

Audio Return Channel (ARC) function enables an HDMI capable TV to send the audio stream to the

HDMI OUT

of the AV receiver.

• This function can be used when:

– Your TV is ARC capable, and

– The

TV/CD

input selector is selected, and

– “

HDMI Ctrl (RIHD)

” is set to “

On

”(

page 47

), and

– “

Audio Return Ch

” is set to “

Auto

” (

page 48

).

En-14

Connecting Your Components

D  E  F  G 

A  B  C 

Connect your components to the appropriate jacks. The default input assignments are shown below. See

“Connection Tips and Video Signal Path” for more information (

page 66

).

The on-screen menus appear only on a TV that is connected to the

HDMI OUT

. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

: Assignment can be changed (

page 41

).

No. Jack/Port

A

AUX INPUT

VIDEO

E

COMPONENT VIDEO

IN 1 (BD/DVD)

Camcorder, etc

B

C

AUDIO L/R

USB, AUX INPUT

VIDEO

USB

*2

*1 iPod/iPhone (video playback) iPod/iPhone, MP3 player,

USB flash drive

D

DIGITAL IN

OPTICAL 1 (GAME)

OPTICAL 2 (TV/CD)

Game consoles

TV, CD player

COAXIAL 1 (BD/DVD) Blu-ray Disc/DVD player

COAXIAL 2 (CBL/SAT) Satellite/cable set-top box,

✔ etc.

IN 2 (CBL/SAT)

Components

Blu-ray Disc/DVD player,

RI dock

Satellite/cable set-top box,

RI dock, etc.

OUT

F

ETHERNET

G

MONITOR OUT

BD/DVD IN

CBL/SAT IN

TV, projector, etc.

Router

TV, projector, etc.

GAME IN

PC IN

TV/CD IN

Blu-ray Disc/DVD player

Satellite/cable set-top box, etc.

Game console, RI dock

Personal computer

TV, CD player, cassette tape deck, MD, CD-R,

Turntable *3 , RI dock

Connections

Note

*1

*2

*3

When

USB

input is selected, you can input video signals from the

AUX INPUT VIDEO

jack. Video signals input from

AUX

INPUT VIDEO

will be output from the

MONITOR OUT

jack.

Do not connect the AV receiver’s

USB

port to a USB port on your computer. Music on your computer cannot be played through the AV receiver in this way.

Connect a turntable (MM) that has a phono preamp built-in. If your turntable (MM) doesn’t have it, you’ll need a commercially available phono preamp.

If your turntable has a moving coil (MC) type cartridge, you’ll need a commercially available MC head amp or MC transformer as well as a phono preamp. See your turntable’s manual for details.

• With connection

D

, you can enjoy Dolby Digital and

DTS. (To listen in Zone 2 as well, use D and G .)

• With connection G , you can listen audio from the external components while you are in Zone 2.

• With connection

G

, if your Blu-ray Disc/DVD player has both the main stereo and multichannel outputs, be sure to connect the main stereo.

En-15

Connecting Onkyo RI Components

1

Make sure that each Onkyo component is connected with an analog audio cable (connection

G

in the hookup examples) (

page 15 ).

2

Make the

u

connection (see the illustration).

3

If you’re using an RI Dock, or cassette tape deck, change the Input Display (

page 35

).

With u

(Remote Interactive), you can use the following special functions:

System On/Auto Power On

When you start playback on a component connected via u

, while the AV receiver is on standby, the AV receiver will automatically turn on and select that component as the input source.

Direct Change

When playback is started on a component connected via u , the AV receiver automatically selects that component as the input source.

Remote Control

You can use the AV receiver’s remote controller to control your other u

-capable Onkyo components, pointing the remote controller at the AV receiver’s remote control sensor instead of the component. You must enter the appropriate remote control code first

(

page 54

).

e.g., cassette tape deck

R L

ANALOG

AUDIO OUT

R L

ANALOG

AUDIO OUT

RI Dock

Note

• Use only u cables for u connections. u cables are supplied with Onkyo components.

• Some components have two u

jacks. You can connect either one to the AV receiver. The other jack is for connecting additional u -capable components.

• Connect only Onkyo components to u jacks. Connecting other manufacturer’s components may cause a malfunction.

• Some components may not support all u

functions. Refer to the manuals supplied with your Onkyo components.

• While Zone 2 is on, the System On/Auto Power On and Direct

Change u

functions do not work.

En-16

Connections

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

Connections

Connecting the Power Cord

1

Plug the power cord into an AC wall outlet.

Note

• Before connecting the power cord, connect all of your speakers and AV components.

• Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

Insert the plug fully into the jack.

Push.

Insert wire.

Release.

Assembling the AM loop antenna

Caution

• Be careful not to injure yourself when using thumbtacks.

Thumbtacks, etc.

AM loop antenna (supplied) Indoor FM antenna (supplied)

Note

• Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

• Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

• If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

• If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

En-17

Turning On/Off the AV

Receiver

8

ON/STANDBY

8

RECEIVER

RECEIVER

Turning On

1

Press

8

ON/STANDBY

on the front panel.

or

Press RECEIVER followed by

8

RECEIVER on the remote controller.

The AV receiver comes on and its display lights.

If the “Update New F/W” window appears.

When a new version of the firmware is available, the notification window “

Update New F/W

” pops up. This notification only appears when the AV receiver is connected to your home network (

page 70

). To perform the firmware update, follow the instructions on screen.

Use the q

/ w

and

ENTER

buttons on the AV receiver or remote controller to select one of the options, and then press

ENTER

.

`

Update Now

Starts the firmware update.

Refer to step 4 of “Update procedure”

(

page 63

).

`

Remind me Later

The update notification will pop up again the next time you turn the AV receiver on.

`

Never Remind me

Disables the automatic update notification.

Tip

• The update notification window can be enabled or disabled in

Update Notice

” (

page 49

).

Turning On & Basic Operations

Turning Off

1

Press

8

ON/STANDBY

on the front panel.

or

Press RECEIVER followed by

8

RECEIVER on the remote controller.

The AV receiver will enter standby mode. To prevent any loud surprises when you turn on the AV receiver, always turn down the volume before you turn it off.

Tip

• The

HYBRID STANDBY

indicator may light depending on the status of settings (

page 40

).

• For details on power management settings, see “Auto Standby”

(

page 46

).

En-18

Playback

The on-screen menus appear only on a TV that is connected to the HDMI OUT . If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller, unless otherwise specified.

Playing the Connected Component

Operating with the remote controller

INPUT SELECTOR

RECEIVER

VOL

q

/

w

Turning On & Basic Operations

Operating on the AV receiver

Input selector buttons

LISTENING MODE MASTER VOLUME

Listening mode buttons

1

Press RECEIVER followed by an INPUT

SELECTOR button.

2

Start playback on the source component.

See also:

• “Playing an iPod/iPhone via USB” (

page 21

)

• “Playing a USB Device” (

page 22

)

• “Listening to vTuner Internet Radio” (

page 22

)

• “Registering Other Internet Radio” (

page 23

)

• “Playing Music Files on a Server” (

page 24

)

• “Remote Playback” (

page 25

)

• “Listening to AM/FM Radio” (

page 26

)

• “iPod/iPhone Playback via Onkyo Dock”

(

page 51

)

• “Controlling Other Components” (

page 53

)

3

To adjust the volume, use VOL

q

/

w

.

4

Select a listening mode and enjoy!

See also:

• “Using the Listening Modes” (

page 28

)

1

Use the input selector buttons to select the input source.

2

Start playback on the source component.

3

To adjust the volume, use the MASTER VOLUME control.

4

Select a listening mode and enjoy!

En-19

Controlling Contents of USB or

Network Devices

Press

USB

or

NET

first.

a b c d e f g h i j k l m n o p q a b c d e f g h i j k l m

TOP MENU

This button displays the top menu for each media or service.

q

/

w

and ENTER

These buttons navigate through the menus.

e

/

r

This button cycles through pages.

PLAYLIST

e

/

r

In Standard Mode (iPod/iPhone), this button selects playlists.

1

This button starts playback.

7

This button selects the beginning of the current song.

Pressing this button twice selects the previous song.

5

This button fast-reverses the current song.

3

This button pauses playback.

SEARCH

You can toggle between the playback screen and the list screen during playback.

DISPLAY

This button switches between song information during playback.

Press this button while the list screen is displayed to return to the playback screen.

ALBUM +/–

In Standard Mode (iPod/iPhone), this button selects albums.

MENU

This button displays the menu of Internet radio services.

RETURN

This button returns to the previous menu.

4

This button fast-forwards the current song.

6

This button selects the next song.

Turning On & Basic Operations

n o p q

2

This button stops playback.

MODE

You can switch between Standard Mode and Extended

Mode.

RANDOM

This button performs random playback.

REPEAT

Press this button repeatedly to cycle through the repeat modes.

Tip

• See “Controlling Other Components” about the operation of other components (

page 53

).

Note

• The buttons you can use will differ depending on the devices and media used for playback.

En-20

Understanding Icons on the Display

This section describes icons that appear on the AV receiver’s display during media playback.

Icon Description

Folder

Track

Playback

Pause

Fast Forward

Fast Reverse

Artist

Album

Repeat One Track

Repeat Folder (USB Device)

Repeat

Shuffle

Shuffle Album (iPod/iPhone)

Playing an iPod/iPhone via USB

The on-screen menus appear only on a TV that is connected to the HDMI OUT .

This section explains how to play music files on the iPod/iPhone.

Compatible iPod/iPhone models

Made for: iPod touch (1st, 2nd, 3rd and 4th generation), iPod classic, iPod nano (2nd, 3rd, 4th, 5th and 6th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone

1

Press USB to select the “USB” input.

Tip

• The same operation can be done by selecting “

USB

” in the

Home menu.

2

Connect the USB cable that comes with the iPod/iPhone to the

USB

port on the front of the AV receiver.

While reading the contents of your iPod/iPhone, the message “

Connecting...

” appears on the AV receiver’s display.

A list of your iPod/iPhone model’s contents appears

(Extended Mode).

The

USB

indicator lights. It will flash if the AV receiver cannot read the iPod/iPhone.

3

Use

q

/

w

to select a folder, and then press ENTER to open it.

Tip

• If you want to operate using the iPod/iPhone or the remote controller, press

MODE

to switch to Standard mode.

• When you disconnect the iPod/iPhone, the AV receiver remembers the current mode. This means that if you disconnect when in Extended Mode, the AV receiver will start in Extended Mode the next time you connect the iPod/iPhone.

Turning On & Basic Operations

• You can also use the q

/ w

,

ENTER

and

TUNING MODE

buttons on the front panel.

TUNING MODE

allows you to switch modes.

• When connecting your iPod/iPhone with a USB cable, we recommend you use an official USB cable from Apple Inc.

4

Use

q

/

w

to select a music file, and press ENTER or

1

to start playback.

Note

• While the message “

Connecting...

” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the

USB

port.

• If you connect an iPod or iPhone to the

USB

port, no sound will be output from the headphones jack.

Extended Mode Control

The content information is displayed (lists are displayed), and you can control the content while looking at the screen.

Top screen list:

Playlists, Artists, Albums, Genres, Songs, Composers,

Shuffle Songs, Now Playing.

Standard Mode Control

The content information is not displayed, but can be operated using the iPod/iPhone or the remote controller.

En-21

Playing a USB Device Listening to vTuner Internet Radio

The on-screen menus appear only on a TV that is connected to the HDMI OUT .

This section explains how to play music files from a USB device (e.g., USB flash drives and MP3 players).

See also:

• “Network/USB Features” (

page 70

)

1

Press USB to select the “USB” input.

2

Plug your USB device into the AV receiver’s

USB port.

The

USB

indicator lights. It will flash if the AV receiver cannot read the USB device.

3

Press ENTER .

A list of the device’s contents appears. To open a folder, use q

/ w

to select it, and then press

ENTER

.

4

Use

q

/

w

to select a music file, and press ENTER or

1

to start playback.

Note

• While the message “

Connecting...

” appears on the AV receiver’s display, do not disconnect the USB cable supplied with your iPod/iPhone or the USB device from the

USB

port.

You need to connect the AV receiver to your home network (

page 70 ). The on-screen menus appear only on a TV that is connected to the HDMI OUT .

The vTuner Internet Radio Service is a portal site featuring radio stations from all over the world.

You can search for stations by categories such as genre or location. The AV receiver is preinstalled with this service.

1

Press

NET

.

The “

NET

” screen appears, and the

NET

indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

Tip

• The same operation can be done by selecting “

Network

Service

” in the Home menu.

2

Use

q

/

w

to select “vTuner Internet Radio” and then press

ENTER

.

3

Use

q

/

w

to select a program and then press

ENTER .

Playback starts.

Track

Ar tist

Album

My Music

Great Ar tist

My Favorite

0 : 11 / 2 : 00

Turning On & Basic Operations

Adding vTuner Internet Radio Stations to

Favorites

There are two ways you can register specific Internet radio stations (programs) from the vTuner Internet

Radio.

Adding to My Favorites

The selected program will be added to “

My Favorites

” on the “

NET

” screen, which appears when pressing

NET

on the remote controller.

1. Press

MENU

with the station selected or while a station is playing.

2. Use q

/ w

to select “

Add to My Favorites

”, and press

ENTER

.

3. Use q / w / e / r to select “

OK

”, and press

ENTER

.

Tip

• You can rename the stations saved in “

My Favorites

(

page 23

).

Adding to vTuner Internet Radio’s Favorites

Select “

vTuner Internet Radio

” and press

ENTER

to display the “

Favorites

” folder that appears on the same screen as “

Stations By Genre

”, “

Stations By

Location

”, etc. This is where your favorite Internet radio bookmarks will be stored.

To register your favorite stations using a personal computer, you need to connect your PC to the same network as the AV receiver. Enter the ID# (MAC address) of your unit on http://onkyo.vtuner.com/. You can then register your favorite radio programs. The ID# is shown at the bottom of the “

vTuner Internet Radio

” top menu, and the AV receiver’s MAC address is shown on “

Network

” of the Setup menu (

page 48

).

Tip

• You can find stations similar to the one being played.

During playback, press

MENU

on the remote controller, select “

Stations like this

” and press

ENTER

.

En-22

Registering Other Internet Radio

You need to connect the AV receiver to your home network (

page 70 ). The on-screen menus appear only on a TV that is connected to the HDMI OUT .

Internet radio URLs in the following formats are supported: PLS, M3U, and podcast (RSS). However, depending on the type of data or audio format used by the

Internet radio station, you may not be able to listen to some stations.

To listen to other Internet radio stations, you must register your station in “

My Favorites

” of the “

NET

” screen, as described below.

Note

• Services available may vary depending on the region. See the separate instructions for more information.

1

Select “Network Setup” on the Setup menu to verify your IP address (

page 49 ).

Take a note of the IP address.

2

On your computer, start your web browser.

3

Enter the AV receiver’s IP address in the browser’s

Internet address (URL) field.

If you are using Internet Explorer ® , you can also enter the URL by selecting “

Open...

” on the “

File

” menu.

Information on the AV receiver is then shown on your

Internet browser (Web Setup).

4

Click on the “My Favorites” tab, and enter the

Internet radio station’s name and URL.

5

Click “Save” to save the Internet radio station.

The Internet radio station is then added to “

My

Favorites

”. To play the registered station, press

NET

, and then select “

My Favorites

” on the “

NET

” screen.

A list of registered Internet radio stations appears.

Select the one that you saved and press

ENTER

.

Tip

• If you want to add a new station directly from “

My Favorites

”, select an empty slot in the list and press

MENU

. Then, select

Create New Station

” and press

ENTER

.

Pressing

ENTER

again will display the keyboard screen. Use that keyboard to enter the station’s name and URL respectively, and then press

ENTER

.

• If you want to delete a station saved in “

My Favorites

” list, press

MENU

with the station selected or while the station is playing.

Then, use q / w to select “

Delete from My Favorites

” and press

ENTER

. You can also delete stations from the Web Setup.

• If you want to rename a station, select the desired station and press

MENU

. Then, use q / w to select “

Rename this station

” and press

ENTER

.

• You can save up to 40 Internet radio stations.

En-23

Turning On & Basic Operations

Playing Music Files on a Server

You need to connect the AV receiver to your home network (

page 70 ). The on-screen menus appear only on a TV that is connected to the HDMI OUT .

This section explains how to play music files on a computer or media server through the AV receiver (Server

Playback).

1

Start your computer or media server.

2

Press NET .

The “

NET

” screen appears. The

NET

indicator lights.

If it flashes, confirm the network connection.

Tip

• The same operation can be done by selecting “

Network

Service

” in the Home menu.

3

Use

q

/

w

to select “DLNA”, and press ENTER .

4

Use

q

/

w

to select a server, and then press ENTER .

The menu is displayed according to the server functions.

Note

• The search function does not work with media servers which do not support this function.

• Photos and movies stored on a media server cannot be accessed from the AV receiver.

• Depending on the sharing settings in the media server, the

AV receiver may not able to access the content. See the instruction manual of the media server.

5

Use

q

/

w

to select an item, and then press ENTER or

1

to start playback.

Track

Ar tist

Album

My favorite song 1

Ar tist name

My favorite album

0 : 11 / 2 : 00

Note

• Depending on the media server,

5

/

4

/

3

may not work.

• If the message “

No Item.

” appears, this means that no information can be retrieved from the server. In this case, check your server, network, and AV receiver connections.

Turning On & Basic Operations

Windows Media Player 11 Setup

This section explains how to configure Windows Media

Player 11 so that the AV receiver can play the music files stored on your computer.

1

Start Windows Media Player 11.

2

On the “Library” menu, select “Media Sharing”.

The “Media Sharing” dialog box appears.

3

Select the “Share my media” check box, and then click “OK”.

A list of the supported devices appears.

4

Select the AV receiver in the list, and then click

“Allow”.

The corresponding icon will be checked.

5

Click “OK” to close the dialog box.

This completes the Windows Media Player 11 configuration.

You can now play the music files in your Windows

Media Player 11 library through the AV receiver.

Tip

• Windows Media Player 11 can be downloaded for free from the Microsoft web site.

En-24

Remote Playback

You need to connect the AV receiver to your home network (

page 70 ). The on-screen menus appear only on a TV that is connected to the HDMI OUT .

Remote Playback means you can play the music files stored on a media server or personal computer with the AV receiver by operating the controller device in the home network.

Windows Media Player 12 Setup

This section explains how to configure Windows Media

Player 12 so that the AV receiver can play the music files stored on your personal computer.

1

Start Windows Media Player 12.

2

On the “Stream” menu, select “Turn on media streaming”.

A dialog box appears.

Tip

• If the media streaming is already activated, clicking on

“More streaming options...” in the “Stream” menu will display a list of the playback devices connected to the network. You can skip step 3.

3

Move your cursor and click on “Turn on media streaming”.

A list of media server appears. Wording may vary slightly depending on the network location.

4

On the “Media streaming options”, select the AV receiver and confirm that it is set to “Allow”.

5

Click “OK” to close the dialog box.

This completes the Windows Media Player 12 configuration.

You can now play the music files in your Windows

Media Player 12 library.

Tip

• On the “Stream” menu, confirm that “Allow remote control of my Player...” is checked.

Using Remote Playback

Turning On & Basic Operations

5

Adjusting the Volume.

You can adjust the volume by adjusting the volume bar in the “Remote playback” window. The default maximum volume level is 64. If you wish to change this, enter the value from the Web Setup in your browser. Refer to step 3 of “Registering Other Internet

Radio” for details (

page 23

).

The volume value of the remote window and the volume value of the AV receiver may not always match.

Adjustments you make to the volume in the AV receiver will not be reflected in the “Remote playback” window.

1

Turn on the AV receiver.

2

Start Windows Media Player 12.

To enable remote playback, you must first configure

Windows Media Player 12.

3

On Windows Media Player 12, right-click on a music file.

The right-click menu appears.

Tip

• For selecting another media server, select the desired media server from the “Other Libraries” menu on Windows Media

Player 12.

4

Select the AV receiver in “Remote playback”.

The “Play to” window appears and playback on the

AV receiver starts. Operations during remote playback can be made from the “Play to” window of Windows 7 on your personal computer.

A playback screen will be displayed on the connected

TV.

Note

• Remote playback cannot be used in any of the following cases:

– Network services are being used.

– Contents are being played from a USB device or iPod/iPhone.

– Zones are turned on.

En-25

Listening to AM/FM Radio

This section describes the procedure of using the buttons on the front panel, unless otherwise specified.

Using the Tuner

With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection.

You can also change the frequency steps (

page 46

).

1

Press AM or FM to select either “AM” or “FM”.

In this example, FM has been selected.

Band Frequency

Tuning into Radio Stations

Auto tuning mode

1

Press TUNING MODE so that the AUTO indicator lights on the AV receiver’s display.

2

Press TUNING

q

/

w

.

Searching stops when a station is found.

When tuned into a station, the

TUNED

indicator lights. When tuned into a stereo FM station, the

FM

STEREO

indicator lights as shown.

TUNED

AUTO

Turning On & Basic Operations

Manual tuning mode

In manual tuning mode, FM stations will be in mono.

1

Press TUNING MODE so that the AUTO indicator goes off on the AV receiver’s display.

2

Press and hold TUNING

q

/

w

.

The frequency stops changing when you release the button.

Press the buttons repeatedly to change the frequency one step at a time.

Tuning into stations by frequency

You can tune into AM and FM stations directly by entering the appropriate frequency.

1

On the remote controller, press AM or FM to select

“AM” or “FM”, followed by D.TUN

.

(Actual display depends on the country.)

FM STEREO

Tip

• Tuning into weak FM stereo stations

If the signal from a stereo FM station is weak, it may be impossible to get good reception. In this case, switch to manual tuning mode and listen to the station in mono.

(Actual display depends on the country.)

2

Within 8 seconds, use the number buttons to enter the frequency of the radio station.

For example, to tune to 87.5 (FM), press

8

,

7

,

5

or

8

,

7

,

5

,

0

.

If you have entered the wrong number, you can retry after 8 seconds.

En-26

Presetting AM/FM Stations

You can store a combination of up to 40 of your favorite

AM/FM radio stations as presets.

1

Tune into the AM/FM station that you want to store as a preset.

See the previous section.

2

Press MEMORY .

The preset number flashes.

Deleting Presets

1

Select the preset that you want to delete.

See the previous section.

2

While holding down MEMORY , press TUNING

MODE .

The preset is deleted and its number disappears from the AV receiver’s display.

(Actual display depends on the country.)

3

While the preset number is flashing (about 8 seconds), use PRESET

e

/

r

to select a preset from

1 through 40.

4

Press MEMORY again to store the station or channel.

The station or channel is stored and the preset number stops flashing.

Repeat this procedure for all of your favorite AM/FM radio stations.

Selecting Presets

1

To select a preset, use PRESET

e

/

r

on the AV receiver, or the remote controller’s CH +/– .

Tip

• You can also use the remote controller’s number buttons to select a preset directly.

En-27

Turning On & Basic Operations

Using Basic Functions

Using the Listening Modes

Selecting Listening Modes

See “About Listening Modes” for detailed information about the listening modes (

page 29

).

Listening Mode Buttons

Press

RECEIVER

first.

MOVIE/TV, MUSIC, GAME

Turning On & Basic Operations

MOVIE/TV button

This button selects the listening modes intended for use with movies and TV.

MUSIC

button

This button selects the listening modes intended for use with music.

GAME

button

This button selects the listening modes intended for use with video games.

STEREO

button

This button selects the Stereo listening mode and All

Channel Stereo listening mode.

• The Dolby Digital and DTS listening modes can only be selected if your Blu-ray Disc/DVD player is connected to the AV receiver with a digital audio connection (coaxial, optical, or HDMI).

• The listening modes you can select depends on the format of the input signal. To check the format, see “Displaying

Source Information” (

page 34 ).

• While a pair of headphones is connected, you can select the following listening modes: Mono, Direct, and Stereo.

MUSIC

MOVIE/TV

GAME

STEREO

En-28

About Listening Modes

The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound.

Explanatory Notes

a b c

Input Source

The following audio formats are supported by the listening modes.

A

This is mono (monophonic) sound.

S This is stereo (stereophonic) sound. Two independent audio signal channels are reproduced through two speakers.

D This is 5.1-channel surround sound. This surround system has five main channels of sound and a sixth subwoofer channel (called the point-one channel).

F

*1

This is 7.1-channel surround sound. This is a further sound enhancement to 5.1-channel sound with two additional speakers that provide greater sound envelopment and more accurate positioning of sounds.

*1

The AV receiver outputs this source in 5.1-channel surround sound.

Turning On & Basic Operations

Speaker Layout

The illustration shows which speakers are activated in each channel. See “Sp Config (Speaker Configuration)” for the speaker setup (

page 42

).

Z

X

C d a Front speakers b

Center speaker c

Surround speakers d

Subwoofer

En-29

Onkyo-Original DSP Listening Modes

Listening Mode

Orchestra

O r c h e s t r a

Unplugged

U n p l u g g e d

Studio-Mix

S t u d i o – M i x

TV Logic

T V L o g i c

Game-RPG

G a m e – R P G

Game-Action

Description Input

Source

Suitable for classical or operatic music, this mode emphasizes the surround channels in order to widen the stereo image, and simulates the natural reverberation of a large hall.

A

S

D

F

Suitable for acoustic instruments, vocals and jazz, this mode emphasizes the front stereo image, giving the impression of being right in front of the stage.

Suitable for rock or pop music, listening to music in this mode creates a lively sound field with a powerful acoustic image, like being at a club or rock concert.

This mode adds realistic acoustics to TV shows produced in a TV studio, surround effects to the entire sound, and clarity to voices.

In this mode, the sound has a dramatic feel with a similar atmosphere to Orchestra mode.

In this mode, sound localization is distinct with emphasis on bass.

G a m e – A c t i o n

Game-Rock

In this mode, sound pressure is emphasized to heighten live feel.

G a m e – R o c k

Game-Sports

In this mode, reverberation is increased and sound localization decreased slightly.

G a m e – S p o r t s

All Ch Stereo

A l l C h S t e r e o

Full Mono

F u l l M o n o

Ideal for background music, this mode fills the entire listening area with stereo sound from the front, and surround.

In this mode, all speakers output the same sound in mono, so the sound you hear is the same regardless of where you are within the listening room.

Speaker

Layout

C

XC

Listening Mode

T-D (Theater-

Dimensional)

T – D

Turning On & Basic Operations

Description Input

Source

With this mode you can enjoy a virtual surround sound even with only two or three speakers. This works by controlling how sounds reach the listener’s left and right ears.

Good results may not be possible if there’s too much reverb, so we recommend that you use this mode in an environment with little or no natural reverb.

A

S

D

F

Speaker

Layout

ZXC

En-30

Listening Modes

Listening Mode

Direct

D i r e c t

Stereo

Description Input

Source

In this mode, audio from the input source is output without surround-sound processing.

The speaker configuration (presence of speakers) and speaker distance settings are enabled, but much of the processing set via the audio setup is disabled. A/V Sync does not have effect on the analog audio. See

“Using the Setup Menu (HOME)” for more details (

page 39

).

Sound is output from the front left and right speakers and subwoofer.

A

S

D

F

S t e r e o

Mono

M o n o

Multichannel

Use this mode when watching an old movie with a mono soundtrack, or use it with the foreign language soundtracks recorded in the left and right channels of some movies. It can also be used with DVDs or other sources containing multiplexed audio, such as karaoke DVDs.

This mode is for use with PCM multichannel sources.

D

F

M u l t i c h

DSD

*1

D S D

Dolby Digital

D o l b y D

Dolby Digital Plus

*2

D o l b y D +

Dolby TrueHD

D o l b y T r u e H D

D

F

Speaker

Layout

ZXC

XC

In this mode, audio from the input source is output without surround-sound processing.

The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via the audio setup are enabled. See “Using the Setup Menu

(HOME)” for more details (

page 39

).

D XC

D

F

XC

XC

Listening Mode

DTS

D T S

DTS-HD High

Resolution Audio

D T S – H D H R

DTS-HD Master

Audio

D T S – H D M S T R

DTS Express

D T S E x p r e s s

DTS 96/24

D T S 9 6 / 2 4

Turning On & Basic Operations

Description Input

Source

Speaker

Layout

D XC

In this mode, audio from the input source is output without surround-sound processing.

The speaker configuration (presence of speakers), crossover frequency, speaker distance, A/V Sync and much of the processing set via the audio setup are enabled. See “Using the Setup Menu

(HOME)” for more details (

page 39

).

D

F

XC

D XC

Dolby Pro Logic II

P L M o v i e

P L M u s i c

P L G a m e

This mode is for use with DTS 96/24 sources. This is high-resolution DTS with a

96 kHz sampling rate and 24-bit resolution, providing superior fidelity. Use it with

DVDs that bear the DTS 96/24 logo.

D XC

Dolby Pro Logic II

expands any 2-channel source for 5.1-channel playback. It provides a very natural and seamless surround-sound experience that fully envelops the listener.

As well as music and movies, video games can also benefit from the dramatic spatial effects and vivid imaging.

• Dolby PLII Movie

Use this mode with DVDs and videos that bear the Dolby Surround logo or TV shows that feature Dolby Surround. You can also use this mode with stereo movies or TV shows and the AV receiver will create a 5.1 surround mix from the 2-channel stereo.

• Dolby PLII Music

Use this mode to add 5.1 surround to stereo sources such as music CDs and DVDs.

• Dolby PLII Game

Use this mode when playing game discs.

S XC

En-31

Listening Mode

Neo:6

N e o : 6 C i n e m a

N e o : 6 M u s i c

Description Input

Source

Speaker

Layout

This mode expands any 2-channel source for up to 5.1-channel playback. It uses seven full-bandwidth channels of matrix decoding for matrix-encoded material, providing a very natural and seamless surround sound experience that fully envelops the listener.

• Neo:6 Cinema

S XC

Use this mode with any stereo movie (e.g.,

TV, DVD, VHS).

• Neo:6 Music

Use this mode with any stereo music source

(e.g., CD, radio, cassette, TV, VHS, DVD).

Note

*1

*2

The AV receiver can input the DSD signal from HDMI IN. Depending on the player, setting the output on the player side to PCM might bring better sound.

For the Blu-ray Discs, Dolby Digital is used in a 3.1/5.1-channel speaker system.

• The listening modes cannot be selected with some source formats.

Turning On & Basic Operations

En-32

Using the Home Menu

The Home menu provides quick access to frequently used menus.

The Home menu appears only on a TV that is connected to the HDMI OUT . If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

1

Press

RECEIVER

followed by

HOME

.

The Home menu will be superimposed on the TV screen.

H o m e

N e t w o r k S e r v i c e

U S B

I n s t a P r e v u e

S e t u p

F / W U p d a t e

2

Use

q

/

w

and ENTER to make the desired selection.

Press

HOME

to close the menu.

Network Service

You need to connect the AV receiver to your home network (

page 70 ).

`

With this selection, you can use various Internet radio services or play the contents stored in media connected to your home network (DLNA) (

page 22

)

. Note that this selection will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

Press

ENTER

to display the “

NET

” screen. If you want to use the Internet radio services, use q

/ w

to select the desired service. Pressing

ENTER

again switches to that selection. If you want to play music files on a server, use q

/ w

to select “

DLNA

” and then press

ENTER

.

USB

`

With this selection, you can play contents of portable players (iPod, etc.) and USB storage devices connected to the AV receiver’s

USB

port (

pages 21

,

22

).

Note that this selection will be grayed out for a short while after the AV receiver is turned on. Please wait until it becomes operable.

Press

ENTER

to select a drive or browse the contents of the media connected, followed by q

/ w

to select the desired folder or track. Pressing

ENTER

as a track is selected will start playback.

InstaPrevue

`

With this selection, you can preview audio/video streams coming from HDMI inputs (

HDMI

IN 1

/

2

/

3

/

4

/

5

). Even with multiple components connected through HDMI, you can easily switch between inputs as their previews are displayed on a single screen.

Press

ENTER

to display the main preview (currently selected HDMI input) and the additional previews

(other HDMI inputs). Use q / w or e / r to select a

Turning On & Basic Operations

preview thumbnail, and pressing

ENTER

will switch the AV receiver to that input source.

Tip

• If no video signals are present, the thumbnails will be filled in black.

• You can specify the number of preview thumbnails as well as their positioning on screen (

page 48

).

Note

• This function cannot be selected when:

HDMI IN 6

is the current HDMI input source, or

– No signal is present on the current input source.

• Depending on video signals, the picture may not be properly rendered on the preview thumbnails of InstaPrevue.

Setup

`

With this selection, you can access the common settings of the on-screen Setup menu.

Press

ENTER

to display the Setup menu

(

page 39

).

Tip

• You can also access frequently used settings from Quick

Setup (

page 37

).

F/W Update

`

With this selection, you can update the firmware of the

AV receiver. Note that this selection will be grayed out for a short while after the AV receiver is turned on.

Please wait until it becomes operable.

Press

ENTER

to start the procedure (

page 62

).

En-33

Using the Sleep Timer

With the sleep timer, you can set the AV receiver to turn off automatically after a specified period.

1

Press RECEIVER once followed by SLEEP repeatedly to select the required sleep time.

The sleep time can be set from 90 to 10 minutes in 10 minute steps.

The

SLEEP

indicator lights on the AV receiver’s display when the sleep timer has been set. The specified sleep time appears for about 5 seconds, then the previous display reappears.

Tip

• If you need to cancel the sleep timer, press

SLEEP

repeatedly until the

SLEEP

indicator goes off.

• To check the time remaining until the AV receiver sleeps, press

SLEEP

. Note that if you press again on

SLEEP

as the time being displayed is 10 minutes or less, the sleep timer will go off.

Setting the Display Brightness

You can adjust the brightness of the AV receiver’s display.

1

Press RECEIVER once followed by DIMMER repeatedly to switch between: normal, dim, or dimmer brightness.

Tip

• Alternatively, you can use the AV receiver’s

DIMMER

.

Turning On & Basic Operations

Displaying Source Information

You can display various information about the current input source as follows.

1

Press RECEIVER once followed by DISPLAY repeatedly to cycle through the available information.

Tip

• Alternatively, you can use the AV receiver’s

DISPLAY

.

The following information can be typically displayed.

Input source

& volume *1

Listening mode

Signal format *2

Sampling frequency *2

*1

*2

When AM or FM radio is used, the band, preset number, and frequency are displayed.

If the input signal is digital, the signal format is displayed.

Information is displayed for about three seconds, then the previously displayed information reappears.

En-34

Changing the Input Display

When you connect an u -capable Onkyo component, you must configure the input display so that u

can work properly.

This setting can be done only from the front panel.

1

Press TV/CD or GAME .

TV/CD

” or “

GAME

” appears on the AV receiver’s display.

2

Press and hold down the same button (about

3 seconds) to change the input display.

Repeat this step to select the desired input display.

TV/CD:

TV/CD

DOCK

TAPE

GAME: GAME

DOCK

Note

• “

DOCK

” can be selected for the “

TV/CD

” or “

GAME

” input selector, but not at the same time.

• Enter the appropriate remote control code before using the remote controller for the first time (

page 54

).

Using the Music Optimizer

The Music Optimizer function enhances the sound quality of compressed music files.

1

Press MUSIC OPTIMIZER on the front panel.

The

M.Opt

indicator lights on the AV receiver’s display.

The

MUSIC OPTIMIZER

indicator lights on the front panel.

Tip

• Alternatively, you can use the remote controller’s

Q SETUP

.

• See “Music Optimizer” for more details (

page 38

).

Turning On & Basic Operations

Muting the AV Receiver

You can temporarily mute the output of the AV receiver.

1

Press RECEIVER followed by MUTING .

The output is muted and the

MUTING

indicator flashes on the AV receiver’s display.

Tip

• To unmute, press

MUTING

again or adjust the volume.

• Muting is automatically cancelled when the AV receiver is set to standby.

En-35

Using Headphones

1

Connect a pair of stereo headphones with a standard plug (1/4 inch or 6.3 mm) to the PHONES jack.

While the headphones plug is inserted in the

PHONES

jack, = indicator lights.

Note

• Always turn down the volume before connecting your headphones.

• While the headphones plug is inserted in the

PHONES

jack, the speakers are turned off.

• When you connect a pair of headphones, the listening mode is set to Stereo, unless it’s already set to Stereo, Mono,

Direct.

• If you connect an iPod or iPhone to the

USB

port on the AV receiver, no sound will be output from the headphones jack.

Turning On & Basic Operations

En-36

On-screen Setup

With the AV receiver connected to a TV, there are two ways of changing the settings on-screen: using the Quick

Setup or the Setup Menu (

HOME

).

Quick Setup

The Quick Setup provides quick access to frequently used settings. You can change settings and view the current information.

Setup menu (HOME)

The Setup menu (

HOME

) provides a convenient way to change the AV receiver’s various settings. Settings are organized into 11 categories.

The on-screen menus appear only on a TV that is connected to the

HDMI OUT

. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

This section describes the procedure for using the remote controller unless otherwise specified.

Note

• The on-screen menus are displayed when:

– There is no video input, or

– The video input is 480p, 720p, 1080i, or 1080p.

Using the Quick Setup

RECEIVER

ENTER

q

/

w

/

e

/

Q SETUP RETURN

1

Press RECEIVER followed by Q SETUP .

The Quick Setup will be superimposed on the TV screen.

2

Use

q

/

w

and ENTER to make the desired selection.

Press

Q SETUP

to close the menu.

Press

RETURN

to return to the previous menu.

Explanatory Notes

a b

Music Optimizer

`

Off

`

On

a

Setting target b Setting options (default setting underlined)

Advanced Operations

Input

`

You can select input sources and view information on their assignments.

Use q

/ w

to select an input source and view its assignment information.

Pressing

ENTER

switches to the selected input source.

Audio (

page 38 )

`

You can change the following settings: “

Bass

”,

Treble

”, “

Subwoofer Level

”, “

Center Level

”, “

Late

Night

”, “

Music Optimizer

”, and “

Cinema Filter

”.

Information

*1

`

You can view the information of the following items:

Input

” and “

Output

”.

Listening Mode

*2

`

You can select the listening modes that are grouped in the following categories: “

MOVIE/TV

”, “

MUSIC

”,

GAME

”.

Use q

/ w

to select the category and e

/ r

to select the listening mode. Press

ENTER

to switch to the selected listening mode.

*1

*2

Note

Depending on the input source and listening mode, not all channels shown here output the sound.

• This setting is not available in either of the following cases:

– The “

Audio TV Out

” setting is set to “

On

” (

page 47

).

– “

HDMI Ctrl (RIHD)

” is set to “

On

” (

page 47

) and you’re listening through your TV speakers.

Q u i c k S e t u p

I n p u t

A u d i o

I n f o r m a t i o n

L i s t e n i n g M o d e

[ E N T E R : S e l e c t ]

En-37

Using the Audio Settings of Quick

Setup

You can change various audio settings from the Quick

Setup (

page 37

).

Note

• These settings are not available in either of the following cases:

– The “

Audio TV Out

” setting is set to “

On

” (

page 47

).

– “

HDMI Ctrl (RIHD)

” is set to “

On

” (

page 47

) and you’re listening through your TV speakers.

Tone Control

Bass

`

–10 dB

to

0 dB

to

+10 dB

in 2 dB steps

You can boost or cut low-frequency sounds output from the front speakers.

Treble

`

–10 dB

to

0 dB

to

+10 dB

in 2 dB steps

You can boost or cut high-frequency sounds output from the front speakers.

You can adjust the bass and treble for the front speakers, except when Direct listening mode is selected.

Operating on the AV receiver

1

Press

TONE

repeatedly to select either “Bass” or

“Treble”.

2

Use – and + to adjust.

Speaker Levels

Subwoofer Level

`

–15 dB

to

0 dB

to

+12 dB

in 1 dB steps

Center Level

`

–12 dB

to

0 dB

to

+12 dB

in 1 dB steps

You can adjust the volume of each speaker while listening to an input source.

These temporary adjustments are cancelled when the AV receiver is set to standby. To save the setting you made here, go to “Level Cal (Level Calibration)” (

page 43

) before setting the AV receiver to standby.

Note

• You cannot use these function while the AV receiver is muted.

• These settings cannot be used while a pair of headphones is connected.

• Speakers that are set to “

No

” or “

None

” in “Sp Config (Speaker

Configuration)” (

page 42

) cannot be adjusted.

Late Night

Late Night

For

Dolby Digital

and

Dolby Digital Plus

sources, the options are:

`

Off

`

Low

:

Small reduction in dynamic range.

`

High

:

Large reduction in dynamic range.

For

Dolby TrueHD

sources, the options are:

`

Auto

:

The Late Night function is set to “

On

” or “

Off

” automatically.

`

Off

`

On

Advanced Operations

Turn this setting on to reduce the dynamic range of Dolby

Digital material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

Note

• The effect of the Late Night function depends on the material that you are playing and the intention of the original sound designer, and with some material there will be little or no effect when you select the different options.

• The Late Night function can be used only when the input source is Dolby Digital, Dolby Digital Plus, or Dolby TrueHD.

• The Late Night function is set to “

Off

” when the AV receiver is set to standby. For Dolby TrueHD sources, it will be set to

Auto

”.

Music Optimizer

Music Optimizer

`

Off

`

On

The Music Optimizer function enhances the sound quality of compressed music files. When set to “

On

”, the

M.Opt

indicator lights on the AV receiver’s display, and the

MUSIC OPTIMIZER

indicator lights on the front panel.

Tip

• Alternatively, you can use the AV receiver’s

MUSIC

OPTIMIZER

.

Note

• The Music Optimizer function only works with PCM digital audio input signals with a sampling rate below 48 kHz and analog audio input signals.

• The Music Optimizer is disabled when the Direct listening mode is selected.

• The setting is stored individually for each input selector.

En-38

Advanced Operations

CinemaFILTER

Cinema Filter

`

Off

`

On

Turn this setting on to soften overly bright movie soundtracks, which are typically mixed for reproduction in a movie theater.

CinemaFILTER can be used with the following listening modes: Dolby Digital, Dolby Digital Plus, Dolby TrueHD,

Dolby Pro Logic II Movie, Multichannel, DTS, DTS Neo:6

Cinema, DTS 96/24, DTS-HD High Resolution Audio,

DTS-HD Master Audio and DTS Express.

Note

• The CinemaFILTER may not work when used with certain input sources.

Using the Setup Menu (HOME)

RECEIVER

ENTER

q

/

w

/

e

/

Remote indicator

RETURN

HOME

1

Press RECEIVER followed by HOME .

2

Use

q

/

w

to select “Setup”, and then press ENTER .

3

Use

q

/

w

to select a menu item, and then press

ENTER .

4

Use

q

/

w

to select a setting target, and use

e

/

r

to change the setting.

Press

HOME

to close the menu.

Press

RETURN

to return to the previous menu.

Explanatory Notes

a b c

Menu

Subwoofer

`

Yes

`

No

Setup

1. HDMI Input

2. Component

3. Digital Audio

4. Sp Config

5. Sp Distance

6. Level Cal

7. Audio Adjust

8. Source Setup

9. Hardware

10. HDMI Setup

11. Network Setup

Menu

Sp Config

a Menu selection b

Setting target c

Setting options (default setting underlined)

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

Setting target

Note

• This procedure can also be performed on the AV receiver by using

SETUP

, the cursor buttons, and

ENTER

.

En-39

About the HYBRID STANDBY indicator

By way of optimized circuitry, this function reduces power consumption when the AV receiver is in standby mode.

The

HYBRID STANDBY

indicator will light in either of the following conditions:

– “

HDMI Through

” is enabled and Zones are turned off

(the

HDMI

indicator is off).

– “

Network Standby

” is enabled and Zones are turned off

(the

NET

indicator is off).

HYBRID STANDBY

Setup menu items

Menu item

HDMI Input

(

page 41

)

Component

(

page 41

)

Digital Audio

(

page 42

)

Sp Config

(

page 42

)

Sp Distance

(

page 43

)

Setting target

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

Subwoofer

Front

Center

Surround

Crossover

Double Bass

Unit

Left

Center

Right

Surround Right

Surround Left

Subwoofer

En-40

Menu item

Level Cal

(

page 43

)

Audio Adjust

(

page 44

)

Source Setup

(

page 45

)

Hardware

(

page 46

)

HDMI Setup

(

page 47

)

Network Setup

(

page 48

)

Advanced Operations

Setting target

Left

Center

Right

Surround Right

Surround Left

Subwoofer

Input Ch (Mux)

Input Ch (Mono)

Panorama

Dimension

Center Width

Center Image

Listening Angle

A/V Sync

Name

Audio Selector

[

Fixed Mode

]

Volume OSD

Remote ID

AM/FM Freq Step

Auto Standby

HDMI Ctrl (RIHD)

HDMI Through

Audio TV Out

Audio Return Ch

LipSync

InstaPrevue

[

Sub Window

,

Position

]

MAC Address

DHCP

[

IP Address

,

Subnet Mask

,

Gateway

,

DNS Server

]

Proxy URL

[

Proxy Port

]

Network Standby

Update Notice

HDMI Input

1 2 3 4 5

Setup

Menu HDMI Input

If you connect a video component to an HDMI input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to

HDMI IN 2

, you must assign “

HDMI2

” to the “

BD/DVD

” input selector.

Here are the default assignments.

Input selector

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

Default assignment

HDMI1

HDMI2

HDMI3

HDMI4

- - - - -

- - - - -

BD/DVD

,

CBL/SAT

,

GAME

,

PC

,

AUX

,

TV/CD

`

HDMI1

,

HDMI2

,

HDMI3

,

HDMI4

,

HDMI5

,

HDMI6

:

Select the input to which the component has been connected.

`

- - - - -

:

Select if you’re not using the

HDMI OUT

.

Each HDMI input cannot be assigned to two input selectors or more. When

HDMI1

-

HDMI6

have already been assigned, you must first set any unused input selectors to “

- - - - -

” or you will be unable to assign

HDMI1

-

HDMI6

to other input selectors.

Note

• If no video component is connected to HDMI output (even if the

HDMI input is assigned), the AV receiver selects the video source based on the setting of “Component (Component Video

Input)”.

• When an

HDMI IN

is assigned to an input selector as explained here, the same

HDMI IN

will be set as a priority in the “

Digital

Audio

” (

page 42

). In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the

Audio Selector

” setting (

page 45

).

• Do not assign an

HDMI IN

to the

TV/CD

selector while “

HDMI

Ctrl (RIHD)

” is set to “

On

” (

page 47

), otherwise appropriate CEC (Consumer Electronics Control) operation will not be guaranteed.

• If you assign “

- - - - -

” to an input selector that is currently selected in “

HDMI Through

” (

page 47

), the “

HDMI

Through

” setting will be automatically switched to “

Off

”.

Advanced Operations

Component (Component Video Input)

1 2 3 4 5

Setup

Menu Component

If you connect a video component to a component video input, you must assign that input to an input selector. For example, if you connect your Blu-ray Disc/DVD player to

COMPONENT VIDEO IN 2

, you must assign “

IN2

” to the “

BD/DVD

” input selector.

Here are the default assignments.

Input selector

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

Default assignment

IN1

IN2

- - - - -

- - - - -

- - - - -

- - - - -

BD/DVD

,

CBL/SAT

,

GAME

,

PC

,

AUX

,

TV/CD

`

IN1

,

IN2

:

Select the input to which the component has been connected.

`

- - - - -

:

Select if you’re not using the

COMPONENT

VIDEO OUT

.

En-41

Digital Audio (Digital Audio Input)

1 2 3 4 5

Setup

Sp Config (Speaker Configuration)

1 2 3 4 5

Setup

Menu Digital Audio

If you connect a component to a digital audio input, you must assign that input to an input selector. For example, if you connect your CD player to the

OPTICAL IN 1

, you must assign “

OPTICAL1

” to the “

TV/CD

” input selector.

Here are the default assignments.

Input selector

BD/DVD

CBL/SAT

GAME

PC

AUX

TV/CD

Default assignment

COAXIAL1

COAXIAL2

OPTICAL1

- - - - -

- - - - -

OPTICAL2

BD/DVD

,

CBL/SAT

,

GAME

,

PC

,

AUX

,

TV/CD

`

COAXIAL1

,

COAXIAL2

,

OPTICAL1

,

OPTICAL2

:

Select the input to which the component has been connected.

`

- - - - -

:

Select if the component is connected to an analog audio input.

Note

• When an

HDMI IN

is assigned to an input selector in

HDMI Input

” (

page 41

), the same

HDMI IN

will be set as a priority in this assignment. In this case, if you want to use the coaxial or optical audio input, make the appropriate selection in the “

Audio Selector

” (

page 45

).

• Available sampling rate for PCM signals (stereo/mono) from a digital input (optical and coaxial) are 32/44.1/48/88.2/96 kHz/16,

20, 24 bit.

Menu Sp Config

This section explains how to specify which speakers are connected and their sizes.

Cone diameter

For speakers with a cone diameter larger than 6-1/2 inches

(16 cm), specify

Large

(full band). For those with a smaller diameter, specify

Small

(default crossover 100Hz).

The crossover frequency can be changed in “Crossover

(Crossover Frequency)”.

Note

• These settings are not available in either of the following cases:

– A pair of headphones is connected.

– The “

Audio TV Out

” setting is set to “

On

” (

page 47

).

– “

HDMI Ctrl (RIHD)

” is set to “

On

” (

page 47

) and you’re listening through your TV speakers.

Subwoofer

`

Yes

`

No

Front

`

Small

:

`

Large

:

Select based on the cone diameter.

Note

• If the “

Subwoofer

” setting is set to “

No

”, this setting is fixed to

Large

”.

Advanced Operations

Center

*1

, Surround

*1

`

Small

:

`

Large

:

Select based on the cone diameter.

`

None

*1

Note

If the “

Front

” setting is set to “ cannot be selected.

Small

”, the “

Large

” option

Crossover (Crossover Frequency)

This setting is advantageous for the speakers that you specified as “

Small

” in

“Sp Config (Speaker

Configuration)”

. To get the best bass performance from your speaker system, you need to set the crossover frequency according to the size and frequency response of your speakers.

`

40Hz

,

50Hz

,

60Hz

,

70Hz

,

80Hz

,

90Hz

,

100Hz

,

120Hz

,

150Hz

,

200Hz

Use the diameter of the smallest speaker in your system when choosing the crossover frequency.

Speaker cone diameter

Over 8 in. (20 cm)

6-1/2 to 8 in. (16 to 20 cm)

5-1/4 to 6-1/2 in. (13 to 16 cm)

3-1/2 to 5-1/4 in. (9 to 13 cm)

Under 3-1/2 in. (9 cm)

Crossover frequency

40/50/60 Hz *

70/80/90 Hz *

100 Hz

120 Hz

150/200 Hz

*

*

Choose the setting matching your speaker.

To be continued

En-42

Note

• For a more accurate setting, look up the frequency response in the manuals supplied with your speakers and set accordingly.

• Choose a higher crossover frequency if you want more sound from your subwoofer.

Double Bass

`

On

`

Off

Turn this setting on to boost bass output by feeding bass sounds from the front left, right, and center channels to the subwoofer.

Note

• When the “

Subwoofer

” setting is set to “

No

” or the “

Front

” setting to “

Small

”, this setting is fixed to “

Off

” (

page 42

).

• This setting is set to “

On

” automatically when the “

Subwoofer

” and “

Front

” settings are set for the first time to “

Yes

” and

Large

” respectively.

Sp Distance (Speaker Distance)

1 2 3 4 5

Setup

Menu Sp Distance

Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

Note

• These settings are not available in either of the following cases:

– A pair of headphones is connected.

– The “

Audio TV Out

” setting is set to “

On

” (

page 47

).

– “

HDMI Ctrl (RIHD)

” is set to “

On

” (

page 47

) and you’re listening through your TV speakers.

Unit

`

feet

:

Distances can be set in feet. Range:

1ft

to

30ft

in

1 foot steps.

`

meters

:

Distances can be set in meters. Range:

0.3m

to

9.0m

in 0.3 meter steps.

Left, Center, Right, Surround Right, Surround

Left, Subwoofer

`

Specify the distance from each speaker to your listening position.

Note

• Speakers that you set to “

No

” or “

None

” in the “Sp Config

(Speaker Configuration)” (

page 42

) cannot be selected.

Advanced Operations

Level Cal (Level Calibration)

1 2 3 4 5

Setup

Menu Level Cal

Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

Note

• These settings cannot be calibrated in either of the following cases:

– A pair of headphones is connected.

– The “

Audio TV Out

” setting is set to “

On

” (

page 47

).

– “

HDMI Ctrl (RIHD)

” is set to “

On

” (

page 47

) and you’re listening through your TV speakers.

– The AV receiver is muted.

Left, Center

*1

, Right, Surround Right, Surround

Left

`

–12 dB

to

0 dB

to

+12 dB

in 1 dB steps.

Subwoofer

*1

`

–15 dB

to

0 dB

to

+12 dB

in 1 dB steps.

Note

• Speakers that you set to “

No

” or “

None

” in “Sp Config (Speaker

Configuration)” (

page 42

) cannot be selected.

*1 For the center speaker and subwoofer, the level settings made by using the Quick Setup are saved in this menu (

page 38

).

Tip

• If you’re using a handheld sound level meter, adjust the level of each speaker so that it reads 75 dB SPL at the listening position, measured with C-weighting and slow reading.

En-43

Audio Adjust

1 2 3 4 5

Setup

Menu Audio Adjust

With the Audio Adjust functions and settings, you can adjust the sound and listening modes as you like.

Multiplex/Mono

Multiplex

Input Ch (Mux)

`

Main

`

Sub

`

Main/Sub

This setting determines which channel of a stereo multiplex source is output. Use it to select audio channels or languages with multiplex sources, multilingual TV broadcasts, and so on.

Mono

Input Ch (Mono)

`

Left+Right

`

Left

`

Right

This setting specifies the channel to be used for playing any 2-channel digital source such as Dolby Digital, or 2channel analog/PCM source in the Mono listening mode.

Dolby

PL II Music (2ch Input)

These settings apply to only 2-channel stereo sources.

Panorama

`

On

`

Off

With this setting, you can broaden the width of the front stereo image when using the Dolby Pro Logic II Music listening mode.

Dimension

`

–3

to

0

to

+3

With this setting, you can move the sound field forward or backward when using the Dolby Pro Logic II Music listening mode. Higher settings move the sound field backward. Lower settings move it forward.

If the stereo image feels too wide, or there’s too much surround sound, move the sound field forward to improve the balance. Conversely, if the stereo image feels like it’s in mono, or there’s not enough surround sound, move it backward.

Center Width

`

0

to

3

to

7

With this setting, you can adjust the width of the sound from the center speaker when using the Dolby Pro Logic II

Music listening mode. Normally, if you’re using a center speaker, the center channel sound is output from only the center speaker. (If you’re not using a center speaker, the center channel sound will be distributed to the front left and right speakers to create a phantom center). This setting controls the front left, right, and center mix, allowing you to adjust the weight of the center channel sound.

Advanced Operations

DTS

Neo:6 Music

Center Image

`

0

to

2

to

5

With this setting, you can specify by how much the front left and right channel output is attenuated in order to create the center channel.

Changing the value from “0” to “5” will spread the sound of the center channel to left and right (outwards).

Theater-Dimensional

Listening Angle

`

Wide

:

Select if the listening angle is greater than 30 degrees.

`

Narrow

:

Select if the listening angle is less than 30 degrees.

With this setting, you can optimize the Theater-

Dimensional listening mode by specifying the angle of the front left and right speakers relative to the listening position. Ideally, the front left and right speakers should be equidistant from the listening position and at an angle close to one of the two available settings.

Front left speaker Front right speaker

Listening angle:

30°

Note

• For best results, we recommend setting “

Narrow

” to 20° and

Wide

” to 40°.

En-44

Source Setup

1 2 3 4 5

Setup

Items can be set individually for each input selector.

Preparation

Press the input selector buttons to select an input source.

Menu

A/V Sync

Source Setup

A/V Sync

`

0 msec

to

400 msec

in 10 msec steps.

When using progressive scanning on your Blu-ray

Disc/DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals.

To view the TV picture while setting the delay, press

ENTER

.

To return to the previous screen, press

RETURN

.

The range of values you can adjust will depend on whether your TV or display supports HDMI Lip Sync and if the

LipSync

” setting is set to “

On

” or not (

page 48

).

Note

• A/V Sync is disabled when the Direct listening mode is used with an analog input source.

• This setting cannot be used with the

NET

input selector.

Preset Name For Input Selector

Name

`

- - -

,

Blu-ray

,

DVD

,

HD DVD

,

VCR

,

DVR

,

Tivo

,

CableSTB

,

SAT STB

,

PS3

,

Wii

,

Xbox

,

PC

,

TV

,

CD

,

TAPE

,

iPod

:

To reset to the default, select “

- - -

”.

You can enter a preset name for each individual input selector for easy identification. When entered, the preset name will be displayed.

Note

• You can’t assign the same preset name to multiple input selectors.

• This setting cannot be used for the

AM

,

FM

,

NET

or

USB

input selector.

Advanced Operations

Audio Selector

Audio Selector

`

ARC

:

The audio signal from your TV tuner can be sent to the

HDMI OUT

of the AV receiver.

*1

With this selection, the TV’s audio can be automatically selected as a priority among other assignments.

`

HDMI

:

This can be selected when

HDMI IN

has been assigned as an input source. If both HDMI (

HDMI

IN

) and digital audio inputs (

COAXIAL IN

or

OPTICAL IN

) have been assigned, HDMI input is automatically selected as a priority.

`

COAXIAL

:

This can be selected when

COAXIAL IN

has been assigned as an input source. If both coaxial and

HDMI inputs have been assigned, coaxial input is automatically selected as a priority.

`

OPTICAL

:

This can be selected when

OPTICAL IN

has been assigned as an input source. If both optical and HDMI inputs have been assigned, optical input is automatically selected as a priority.

`

ANALOG

:

The AV receiver always outputs analog signals.

You can set priorities of audio output when there are both digital and analog inputs.

Note

• This setting can be made only for the input source that is assigned as

HDMI IN

,

COAXIAL IN

, or

OPTICAL IN

.

*1 You can select “

ARC

” if you select the

TV/CD

input selector.

But you cannot if you’ve selected “

Off

” in the “

Audio Return

Ch

” setting (

page 48

).

En-45

Setting the Incoming Digital Signal (Fixed

Mode)

Fixed Mode

`

Off

:

The format is detected automatically. If no digital input signal is present, the corresponding analog input is used instead.

`

PCM

:

Only 2-channel PCM format input signals will be heard. If the input signal is not PCM, the

PCM

indicator will flash and noise may also be produced.

`

DTS

:

Only DTS (but not DTS-HD) format input signals will be heard. If the input signal is not DTS, the

dts

indicator will flash and there will be no sound.

When “

HDMI

”, “

COAXIAL

” or “

OPTICAL

” is selected in the “

Audio Selector

” setting, you can then specify the signal type in “

Fixed Mode

”.

Normally, the AV receiver detects the signal format automatically. However, if you experience either of the following issues when playing PCM or DTS material, you can manually set the signal format to PCM or DTS.

• If the beginnings of tracks from a PCM source are cut off, try setting the format to PCM.

• If noise is produced when fast forwarding or reversing a

DTS CD, try setting the format to DTS.

Note

• The setting will be reset to “

Off

” when you change the setting in

Audio Selector

” (

page 45

).

Hardware

1 2 3 4 5

Setup

Menu

OSD

Hardware

Volume OSD

`

On

`

Off

Turn this setting on to display the volume level on the TV screen while it is adjusted.

Remote ID

Remote ID

`

1

,

2

, or

3

When several Onkyo components are used in the same room, their remote ID codes may overlap. To differentiate the AV receiver from other components, you can change its remote ID from “

1

”, to “

2

” or “

3

”.

Note

• If you do change the AV receiver’s remote ID, be sure to change the remote controller to the same ID (see below), otherwise, you won’t be able to control it with the remote controller.

Changing the remote controller’s ID

1

While holding down RECEIVER , press and hold down Q SETUP until the remote indicator lights

(about 3 seconds).

2

Use the number buttons to enter ID 1, 2, or 3.

The remote indicator flashes twice.

Advanced Operations

Tuner

AM/FM Freq Step

`

10kHz/200kHz

:

`

9kHz/50kHz

:

Select the frequency step according to your area.

For AM/FM tuning to work properly, you must specify the

AM/FM frequency step used in your area.

Note

• When this setting is changed, all radio presets will be deleted.

Auto Standby

Auto Standby

`

Off

`

On

When “

Auto Standby

” is set to “

On

”, the

ASb

indicator lights and the AV receiver will automatically enter standby mode if there is no operation for 30 minutes with no audio and no video signal input.

Auto Standby

” will appear on the AV receiver’s display and OSD 30 seconds before the Auto Standby comes on.

Note

• Set to “

On

”, the Auto Standby function may activate itself during playback with some sources.

• The Auto Standby function does not work when Zone 2 is on.

En-46

HDMI Setup

1 2 3 4 5

Setup

Menu HDMI Setup

HDMI Ctrl (RIHD)

`

Off

`

On

Turn this setting on to allow p -compatible components connected via HDMI to be controlled by the

AV receiver (

page 67

).

Note

• When the setting is set to “

On

” and the menu is closed, the names of connected p -compatible components and “

RIHD On

” are displayed on the AV receiver.

Search…

(name)

RIHD On

When the AV receiver cannot receive the name of the component, it is displayed as “

Player *

” or “

Recorder *

”, etc (“

*

” shows up and indicates the number of components, when two or more are received).

• When an p

-compatible component is connected to the

AV receiver via an HDMI cable, the name of the connected component is displayed on the AV receiver display. For example, while you are watching TV broadcasting, if you operate a Blu-ray

Disc/DVD player (being powered on) with the remote control of the AV receiver, the name of the Blu-ray Disc/DVD player will be displayed on the AV receiver.

• Set it to “

Off

” when a connected piece of equipment is not compatible or it is unclear whether the equipment is compatible or not.

• If operation is not normal when set to

On

”, change the setting to

Off

”.

• Refer to the connected component’s instruction manual for details.

• When the “

HDMI Ctrl (RIHD)

” setting is set to “

On

”, the power consumption in standby mode slightly increases. (Depending on the TV status, the AV receiver will enter standby mode as usual.)

• When the source equipment is connected with the u connection, it may malfunction if “

HDMI Ctrl (RIHD)

” is set to

On

”.

HDMI Through

`

Off

`

BD/DVD

,

CBL/SAT

,

GAME

,

PC

,

AUX

,

TV/CD

:

Selects the input source for which the HDMI

Through function is enabled.

`

Last

:

The HDMI Through function is activated on the input source selected at the time of setting the AV receiver to standby mode.

When enabling the HDMI Through function, regardless of whether the AV receiver is on or in standby, both audio and video streams from an HDMI input will be output to the TV or other components via HDMI connection. The

HDMI

indicator will be dimly-lit in standby mode. Note that the indicator may not light under certain conditions

(

page 40

).

This setting is fixed to “

Auto

” automatically when the above “

HDMI Ctrl (RIHD)

” setting is set to “

On

”, resulting in automatic input source selection.

Note

• Only the input source assigned to the

HDMI IN

via

HDMI Input

” is enabled (

page 41

).

• The power consumption in standby mode will increase during the

HDMI Through function; however in the following cases, the power consumption can be saved:

– The TV is in standby mode.

– You are watching a TV program.

• Refer to the connected component’s instruction manual for details.

• Depending on the connected component, the correct input source may not be selected with the setting fixed to “

Auto

”.

• This setting is set to “

Off

” automatically when the “

HDMI Ctrl

(RIHD)

” setting is set to “

Off

”.

Advanced Operations

Audio TV Out

`

Off

`

On

This preference determines whether the incoming audio signal is output from the HDMI output. You may want to turn this preference on if your TV is connected to the

HDMI output and you want to listen to the audio from a connected component through your TV’s speakers.

Normally, this should be set to “

Off

”.

Note

• If “

On

” is selected and the audio can be output from the TV, the

AV receiver will output no sound through its speakers. In this case, “

TV Speaker

” appears on the AV receiver’s display by pressing

DISPLAY

.

• When “

HDMI Ctrl (RIHD)

” is set to “

On

”, this setting is fixed to “

Auto

”.

• With some TVs and input signals, no sound may be output even when this setting is set to “

On

”.

• When “

Audio TV Out

” or “

HDMI Ctrl (RIHD)

” is set to “

On

” and you’re listening through your TV’s speakers (

page 14

), turning up the AV receiver’s volume control will make the sound be output from the AV receiver’s front left and right speakers. To stop the AV receiver’s speakers producing sound, change the settings, change your TV’s settings, or turn down the AV receiver’s volume.

• Listening mode cannot be changed when this setting is set to

On

” and the input source is not HDMI.

En-47

Audio Return Ch (ARC)

`

Off

`

Auto

:

The audio signal from your TV tuner can be sent to the

HDMI OUT

of the AV receiver.

The audio return channel (ARC) function allows an ARC capable TV to send the audio stream to the

HDMI OUT

of the AV receiver. To use this function, you must select the

TV/CD

input selector and your TV must be ARC capable.

The

ARC

indicator will light when the audio signal is detected.

Note

• This setting is fixed to “

- - - -

” when the “

HDMI Ctrl (RIHD)

” setting is set to “

Off

”.

• This setting is set to “

Auto

” automatically when the “

HDMI Ctrl

(RIHD)

” setting is set to “

On

” for the first time.

• If you set “

Audio Return Ch

” to “

Auto

”, the “

Audio Selector

” settings of the

TV/CD

input selector will be automatically switched to “

ARC

” (

page 45

).

LipSync

`

Off

`

On

This function allows the AV receiver to automatically correct any delay between the video and the audio, based on the data from the connected monitor.

Note

• This function works only if your HDMI-compatible TV supports

HDMI Lip Sync.

InstaPrevue

These settings apply to “

InstaPrevue

” of the Home menu

(

page 33

)

and specify the preview display of HDMI video streams.

Sub Window

`

Multi

:

Displays preview thumbnails all at once.

`

Single

:

Displays preview thumbnails one-by-one.

With this setting, you can set the number of preview thumbnails displayed.

Position

(with “

Sub Window

” set to “

Multi

”)

`

Top

,

Bottom

,

Left

,

Right

(with “

Sub Window

” set to “

Single

”)

`

UpperL

,

UpperR

,

LowerL

,

LowerR

With this setting, you can set the position of preview thumbnails on the TV screen.

Note

• Depending on video signals, the picture may not be properly rendered on the preview thumbnails of InstaPrevue.

After changing the settings of the “

HDMI Ctrl

(RIHD)

”, “

HDMI Through

” or “

Audio Return Ch

”, turn off the power on all connected pieces of equipment and then turn them on again. Refer to the user’s manuals for all connected pieces of equipment.

Advanced Operations

Network Setup

1 2 3 4 5

Setup

Menu Network Setup

After modifying the network settings, you must confirm the changes by executing “

Save

”.

This section explains how to configure the AV receiver’s network settings manually.

If your router’s DHCP server is enabled, you don’t need to change any of these settings, as the AV receiver is set to use DHCP to configure itself automatically by default (i.e.,

DHCP is set to “

Enable

”). If, however, your router’s

DHCP server is disabled (you’re for example using static

IP), you’ll need to configure these settings yourself, in which case, a knowledge of Ethernet networking is essential.

What’s DHCP?

DHCP (Dynamic Host Configuration Protocol) is used by routers, computers, the AV receiver, and other devices to automatically configure themselves on a network.

What’s DNS?

The DNS (Domain Name System) translates domain names into IP addresses. For example, when you enter a domain name such as

www.onkyousa.com

in your Web browser, before accessing the site, your browser uses DNS to translate this into an IP address, in this case

63.148.251.142.

MAC Address

This is the AV receiver’s MAC (Media Access Control) address. This address cannot be changed.

En-48

DHCP

`

Enable

`

Disable

This setting determines whether or not the AV receiver uses DHCP to automatically configure its IP Address,

Subnet Mask, Gateway, and DNS Server settings.

Note

• If you select “

Disable

”, you must configure the “

IP Address

”,

Subnet Mask

”, “

Gateway

”, and “

DNS Server

” settings yourself.

IP Address

`

Class A:

10.0.0.0

” to “

10.255.255.255

`

Class B:

172.16.0.0

” to “

172.31.255.255

`

Class C:

192.168.0.0

” to “

192.168.255.255

Enter a static IP address provided by your Internet Service

Provider (ISP).

Most routers use Class C IP addresses.

Subnet Mask

Enter the subnet mask address provided by your ISP

(typically

255.255.255.0

).

Gateway

Enter the gateway address provided by your ISP.

DNS Server

Enter the DNS server address provided by your ISP.

Proxy URL

To use a Web proxy, enter its URL here.

Proxy Port

If you’re using a Web proxy, enter a proxy port number here.

Network Standby

`

On

`

Off

This setting enables or disables control over the network.

When enabled, the

NET

indicator will be dimly-lit while the AV receiver is in standby mode. Note that the indicator may not light under certain conditions (

page 40

).

Note

• When set to “

On

”, the power consumption slightly increases in standby mode.

Update Notice

`

Enable

`

Disable

When this setting is enabled, you will be notified if a firmware update via network is available.

Note

• Selecting “

Never Remind me

” on the notification window will switch this setting to “

Disable

” (

page 18

).

• For details on the update notification, see “If the “Update New

F/W” window appears.” (

page 18

).

En-49

Advanced Operations

Zone 2

In addition to the main listening room, you can also enjoy playback in another room, or as we call Zone 2. And, you can select a different source for each room.

Making Zone 2 Connections

Connecting the Zone Speakers to an

Additional Amplifier

This setup allows 5.1-channel playback in your main listening room and 2-channel stereo playback in Zone 2.

Main room

TV

AV receiver

Controlling Zone 2 Components

Operating on the AV receiver

Input selector buttons

ZONE 2 OFF

Advanced Operations

1

Press ZONE2 , then point the remote controller at the AV receiver and press

8

RECEIVER .

Zone 2 turns on, the

Z2

indicator lights on the AV receiver’s display.

2

To select an input source for Zone 2, press ZONE2 , followed by an INPUT SELECTOR button.

3

To turn off Zone 2, press ZONE2 , followed by

8

RECEIVER .

The zone is turned off.

1

To turn on Zone 2 and select an input source, press

ZONE 2 followed by an input selector button within

8 seconds.

Zone 2 turns on, the

Z2

indicator lights on the AV receiver’s display.

To select the same source as the main room’s, press

ZONE 2

twice. “

Z2 Selector: Source

” appears on the

AV receiver’s display.

2

To turn off Zone 2, press

OFF

.

The zone is turned off.

Operating on the remote controller

To control Zone 2, you must press

ZONE2

on the remote controller first.

Note

• Only analog input sources are output by the

ZONE 2 LINE

OUT

. Digital input sources are not output. If no sound is heard when an input source is selected, verify that the source is connected to an analog input.

• You cannot select different AM or FM radio stations for your main room and Zone 2. The same AM/FM radio station will be heard in each room. Namely, if you have selected an FM station for the main room, that station will also be output in Zone 2.

• When you have selected

NET

or

USB

as the input selector, the last selector selected will be set for Main room and Zone 2.

• When Zone 2 is activated and its input selector is selected, the power consumption of standby mode slightly increases.

• While Zone 2 is on, u functions will not work.

• When setting the AV receiver to standby mode while Zone 2 is active, the

Z2

indicator is dimly lit.

8

RECEIVER

ZONE2

INPUT

SELECTOR

Zone 2

L

IN

R

Receiver/ integrated amp

Note

• The volume of Zone 2 must be set on the Zone 2 amplifier.

En-50

iPod/iPhone Playback via Onkyo Dock

Using the Onkyo Dock

The Dock is sold separately. Models sold are different depending on the region.

For the latest information on the Onkyo Dock components, see the Onkyo web site at: http://www.onkyo.com

Before using the Onkyo Dock components, update your iPod/iPhone with the latest software, available from the Apple web site.

For supported iPod/iPhone models, see the instruction manual of the Onkyo Dock.

RI Dock

With the RI Dock, you can easily play the music stored on your Apple iPod/iPhone through the AV receiver and enjoy great sound, and watch iPod/iPhone slideshows and videos on your TV. In addition, the on-screen display (OSD) allows you to view, navigate, and select your iPod/iPhone model’s contents on your TV, and with the supplied remote controller, you can control your iPod/iPhone from the comfort of your sofa. You can even use the AV receiver’s remote controller to operate your iPod/iPhone.

Note

• Enter the appropriate remote control code before using the AV receiver’s remote controller for the first time (

page 53

).

• Connect the RI Dock to the AV receiver with an u cable

(

page 16

).

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

• Set the AV receiver’s Input Display to “

DOCK

” (

page 35

).

System Function

Depending on your iPod/iPhone model and generation, some of the linked operations may not be available.

System On

When you turn on the AV receiver, the RI Dock and iPod/iPhone turn on automatically. In addition, when RI

Dock and iPod/iPhone are on, the AV receiver can be turned on by pressing

8

SOURCE

.

Auto Power On

If you press the remote controller’s 1 (Playback) while the AV receiver is on standby, the AV receiver will automatically turn on, select your iPod/iPhone as the input source, and your iPod/iPhone will start playback.

Direct Change

If you start iPod/iPhone playback while listening to another input source, the AV receiver will automatically switch to the input to which the RI Dock is connected.

Controlling Other Components

Other Remote Operations

You can use the remote controller that came with the AV receiver to control other iPod/iPhone functions. The available functionality depends on the AV receiver.

Note

• If you use your iPod/iPhone with any other accessories, iPod/iPhone playback detection may not work.

• The System On function may not work depending on the RI

Dock.

iPod Alarm

If you use the Alarm function on your iPod to start playback, the AV receiver will turn on at the specified time and select your iPod as the input source automatically.

Note

• This linked operation won’t work while a video is being played or when the sound set for the alarm is a built-in sound (Beep).

• This linked operation won’t work with models on which music files cannot be used to set the alarm sound.

Operating Notes

• Use the AV receiver’s volume control to adjust the playback volume.

• While your iPod/iPhone is inserted in the RI Dock, its volume control has no effect.

• If you do adjust the volume control on your iPod/iPhone while it’s inserted in the RI Dock, be careful that it’s not set too loud before you reconnect your headphones.

En-51

Controlling Your iPod/iPhone

By pressing the

REMOTE MODE

button that’s been programmed with the remote control code for your Dock, you can control your iPod/iPhone in the Dock with the buttons described further in this section.

See “Entering Remote Control Codes” for details on entering a remote control code (

page 53

).

See the Dock’s instruction manual for more information.

RI Dock

• Set the RI Dock’s RI MODE switch to “HDD” or

“HDD/DOCK”.

8

SOURCE

may not work with a remote control code

(without u ). In this case, make an u connection and enter the remote control code

81993

(with u ).

With the RI Control

Make an u

connection and enter the remote control code

81993

(with u

).

• Set the AV receiver’s Input Display to “

DOCK

(

page 35

).

Without the RI Control

You must enter the remote control code

82990

first

(

page 54

).

a b c d

Press the appropriate

REMOTE

MODE

button first.

e f g h i j k

■ u

Dock operation

Available buttons

a

TOP MENU

*1 b q / w / e / r ,

ENTER

PLAYLIST

e

/ r c 1

,

3

,

2

,

5

,

4

,

7 , 6 d

REPEAT

RANDOM

Controlling Other Components

e 8

SOURCE

*2 f

DISPLAY

*3 g

MUTING

h

ALBUM +/–

i

VOL

q / w j

MENU

k

MODE

*4

• With some iPod/iPhone models, generations and RI Docks, certain buttons may not work as expected.

• For detailed operation of iPod/iPhone, please refer to the instruction manual of the RI Dock.

*1

TOP MENU

works as the mode button when used with the

*2

DS-A2 RI Dock.

This button does not turn the Onkyo DS-A2 or DS-A2X RI

Dock on or off. Also, your iPod/iPhone may not respond the first time you press this button, in which case you should press it again. This is because the remote controller transmits the On and Standby commands alternately, so if your iPod/iPhone is already on, it will remain on when the remote controller transmits the On command. Similarly, if your iPod/iPhone is

*3

*4 already off, it will remain off when the remote controller transmits the Off command.

DISPLAY

turns on the backlight for a few seconds.

Resume mode

With the Resume function, you can resume playback of the song that was playing when you removed your iPod/iPhone from the Onkyo DS-A2 RI Dock.

En-52

Controlling Other

Components

You can use the AV receiver’s remote controller to control your other AV components. This section explains how to enter the remote control code for a component that you want to control: DVD, TV, CD, etc.

Preprogrammed Remote Control

Codes

The following

REMOTE MODE

buttons are preprogrammed with remote control codes for controlling the components listed. You do not need to enter a remote control code to control these components.

For details on controlling these components, see the indicated pages.

BD/DVD

Onkyo Blu-ray Disc player (

page 55

)

TV/CD

Onkyo CD player (

page 54

)

Entering Remote Control Codes

You’ll need to enter a code for each component that you want to control.

1

Look up the appropriate remote control code in the separate Remote Control Codes list.

The codes are organized by category (e.g., DVD player, TV, etc.).

2

While holding down the

REMOTE MODE

button to which you want to assign a code, press and hold down DISPLAY (about 3 seconds).

The remote indicator lights.

Note

• Remote control codes cannot be entered for

RECEIVER

and the multi zone button.

• Only TV remote control codes can be entered for

TV

.

• Except for

RECEIVER

,

TV

, and the multi zone button, remote control codes from any category can be assigned for the

REMOTE MODE

buttons. However, these buttons also work as input selector buttons (

page 19

), so choose a

REMOTE MODE

button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose

TV/CD

when entering its remote control code.

3

Within 30 seconds, use the number buttons to enter the 5-digit remote control code.

The remote indicator flashes twice.

If the remote control code is not entered successfully, the remote indicator will flash once slowly.

Controlling Other Components

Remapping Colored Buttons

You can change the configuration of colored buttons, with which

REMOTE MODE

buttons are preset.

1

While holding down the REMOTE MODE button that you want to program, press and hold down A

(Red) until the remote indicator lights (about 3 seconds).

You can only change colored buttons for components whose codes belong to categories of the Remote

Control Codes list (BD/DVD player, TV, cable set-top box, etc).

2

Within 30 seconds, press the colored buttons in the order that you want to reassign them.

The button presses are assigned to each button from left to right. The remote indicator flashes twice, indicating that the sequence has been successfully assigned. If the sequence is not successfully assigned, the remote indicator will flash once slowly.

Tip

• To reset the

REMOTE MODE

buttons to their default settings, see “Resetting the REMOTE MODE Buttons” (

page 54

).

Note

• If any other button than the colored buttons is pressed, the operation will be cancelled.

• This operation cannot be done while the AV receiver is in

Receiver mode or when ZONE 2 is active.

Note

• Though the provided remote control codes are correct at the time of release, they are subject to change.

En-53

Remote Control Codes for Onkyo

Components Connected via RI

Onkyo components that are connected via u

are controlled by pointing the remote controller at the AV receiver, not the component. This allows you to control components that are out of view, in a rack, for example.

1

Make sure the Onkyo component is connected with an

u

cable and an analog audio cable (RCA).

See “Connecting Onkyo RI Components” for details

(

page 16

).

2

Enter the appropriate remote control code for a

REMOTE MODE button, by referring to the previous section.

`

42157

:

Onkyo cassette tape deck with u

`

81993

:

Onkyo Dock with u

3

Press the

REMOTE MODE

button, point the remote controller at the AV receiver, and operate the component.

Controlling Onkyo components without

u

If you want to control an Onkyo component by pointing the remote controller directly at it, or you want to control an

Onkyo component that’s not connected via u

, use the following remote control codes:

`

30627

:

Onkyo DVD player without u

`

71817

:

Onkyo CD player without u

`

32900/33100/33500

:

Onkyo Blu-ray Disc player

`

32901/33104/33504

:

Onkyo HD DVD player

`

70868

:

Onkyo MD recorder without u

`

71323

:

Onkyo CD recorder without u

`

82990

:

Onkyo Dock without u

Resetting the REMOTE MODE Buttons

You can reset a

REMOTE MODE

button to its default remote control code.

1

While holding down the REMOTE MODE button that you want to reset, press and hold down HOME until the remote indicator lights (about 3 seconds).

2

Within 30 seconds, press the REMOTE MODE button again.

The remote indicator flashes twice, indicating that the button has been reset.

Each

REMOTE MODE

button is preprogrammed with a remote control code. When a button is reset, its preprogrammed code is restored.

Resetting the Remote Controller

You can reset the remote controller to its default settings.

1

While holding down RECEIVER , press and hold down HOME until the remote indicator lights

(about 3 seconds).

2

Within 30 seconds, press

RECEIVER

again.

The remote indicator flashes twice, indicating that the remote controller has been reset.

Controlling Other Components

Controlling Other Components

By pressing the

REMOTE MODE

button that’s been programmed with the remote control code for your component, you can control your component as described below.

For details on entering a remote control code for other components, see “Entering Remote Control Codes”

(

page 53

).

Controlling a TV

TV

is preprogrammed with the remote control code for controlling a TV that supports the p

*1

(limited to some models). The TV must be able to receive remote control commands via p

and be connected to the

AV receiver via HDMI. If controlling your TV via p

doesn’t work very well, program your TV’s remote control code into

TV

and use the TV remote mode to control your TV.

Use the following remote control codes:

`

11807/13100/13500

:

TV with p

Controlling Apple TV

By programming the supplied remote controller with the appropriate remote control code, you can use it to operate your Apple TV.

Use the following remote control codes:

`

02615

:

Apple TV

En-54

Controlling a Blu-ray Disc/DVD Player, HD

DVD Player or DVD Recorder

BD/DVD

is preprogrammed with the remote control code for controlling a component that supports the p

*1

(limited to some models). The component must be able to receive remote control commands via p

and be connected to the AV receiver via HDMI.

Use the following remote control codes:

`

32910/33101/33501/31612

:

Blu-ray Disc/DVD player with p

*1

The p

supported by the AV receiver is the CEC system control function of the HDMI standard.

a b c d e f g

Press the appropriate

REMOTE

MODE

button first.

i j k l m n h o

Controlling Other Components

TV operation

Available buttons

a 8 ,

INPUT

,

TV VOL

q / w ,

MUTING

b c q

/ w

/ e

/ r d

GUIDE

ENTER

SETUP

e 1

,

3

,

2

,

5

,

4

,

7 , 6 *1 f

A

(Red) *1

B

(Green)

*1

C

(Yellow) *1

D

(Blue) *1 g

Number:

1

to

9

,

0

Number:

+10

*1 i

DISPLAY

k

CH +/–

l

PREV CH

m

RETURN

n

AUDIO

*1 o

CLR

Blu-ray Disc player/HD DVD player operation

Available buttons

b

TOP MENU

c q / w / e / r

ENTER

d

SETUP

e 1

,

3

,

2

,

5

,

4

,

7

,

6 f

A

(Red)

B

(Green)

C

(Yellow)

D

(Blue) g Number:

1

to

9

,

0

Number:

+10

*1 h 8

SOURCE

i

DISPLAY

j

MUTING

k

CH +/–

DISC +/–

l

MENU

m

RETURN

n

AUDIO

*1 o

CLR

En-55

a b c d e f g

Press the appropriate

REMOTE

MODE

button first.

i j k l m n h o

DVD player/DVD recorder operation

Available buttons

b

TOP MENU

c q

/ w

/ e

/ r

ENTER

d

SETUP

e 1

,

3

,

2

,

5

,

4

,

7 , 6 f

A

(Red) *1

B

(Green)

C

(Yellow)

*1

D

(Blue) *1 g

Number:

1

to

9

,

0

Number:

+10

*1 h 8

SOURCE

i

DISPLAY

j

MUTING

k

CH +/–

DISC +/–

l

MENU

m

RETURN

n

AUDIO

*1 o

CLR

VCR/PVR operation

Available buttons

b

GUIDE

c q / w / e / r

ENTER

d

SETUP

e 1

,

3

,

2

,

5

,

4

,

7

,

6 g

Number:

1

to

9

,

0

Number:

+10

h 8

SOURCE

i

DISPLAY

j

MUTING

k

CH +/–

l

PREV CH

m

RETURN

o

CLR

Cassette tape deck operation

Available buttons

e 1 , t (Reverse

Playback), 2 , 5 , 4 ,

7

,

6 h 8

SOURCE

j

MUTING

Controlling Other Components

Satellite receiver/Cable receiver operation

Available buttons

b

GUIDE

c q / w / e / r

ENTER

d

SETUP

e 1

,

3

,

2

,

5

,

4

,

7 , 6 f

A

(Red)

B

(Green)

C

(Yellow)

D

(Blue) g

Number:

1

to

9

,

0

Number:

+10

h 8

SOURCE

i

DISPLAY

j

MUTING

k

CH +/–

l

PREV CH

m

RETURN

n

AUDIO

o

CLR

CD player/CD recorder/MD recorder operation

Available buttons

c q / w / e / r

ENTER

d

SETUP

e 1

,

3

,

2

,

5

,

4

,

7 , 6 f

SEARCH

REPEAT

RANDOM

MODE

g

Number:

1

to

9

,

0

Number:

+10

h 8

SOURCE

i

DISPLAY

j

MUTING

k

DISC +/–

o

CLR

Note

• With some components, certain buttons may not work as expected, and some may not work at all.

• See “Controlling Your iPod/iPhone” about the operation of iPod/iPhone (

page 52

).

*1

The p

function is not supported. The p supported by the AV receiver is the CEC system control function of the HDMI standard.

En-56

Troubleshooting

If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact your Onkyo dealer.

If you can’t resolve the issue yourself, try resetting the

AV receiver before contacting your Onkyo dealer.

To reset the AV receiver to its factory defaults, turn it on and, while holding down CBL/SAT , press

8

ON/STANDBY . “Clear” will appear on the AV receiver’s display and the AV receiver will enter standby mode.

Note that resetting the AV receiver will delete your radio presets and custom settings.

Remote indicator

RECEIVER

HOME

To reset the remote controller to its factory defaults, while holding down

RECEIVER

, press and hold down

HOME

until the remote indicator lights (about 3 seconds). Within 30 seconds, press

RECEIVER

again.

The on-screen menus appear only on a TV that is connected to the

HDMI OUT

. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Power

Can’t turn on the AV receiver

Make sure that the power cord is properly plugged into the wall outlet.

Unplug the power cord from the wall outlet, wait five seconds or more, then plug it in again.

The AV receiver turns off unexpectedly

The AV receiver will automatically enter standby mode when Auto Standby has been set and launches.

46

The AV receiver turns off and after restoring the power, it turns off again

The protection circuit has been activated. Remove the power cord from the wall outlet immediately. Make sure that all speaker cables and input sources are properly connected, and leave the AV receiver with its power cord disconnected for 1 hour. After that, reconnect the power cord and turn the power on. If the AV receiver turns off again, unplug the power cord and contact your Onkyo dealer.

Caution: If “

CHECK SP WIRE

” appears on the AV receiver’s display, the speaker cables may be shorting.

12

WARNING

If smoke, smell or abnormal noise is produced by the AV receiver, unplug the power cord from the wall outlet immediately and contact your Onkyo dealer.

Appendix

Audio

There’s no sound, or it’s very quiet

Make sure that the digital input source is selected properly.

Make sure that all audio connecting plugs are pushed in all the way.

42

13

Make sure that the inputs and outputs of all components are connected properly.

Make sure that the polarity of the speaker cables is correct, and that the bare wires are in contact with the metal part of each speaker terminal.

14

12

-

16

Make sure that the input source is properly selected.

19

Make sure that the speaker cables are not shorting.

12

Check the volume. The AV receiver is designed for home theater enjoyment. It has a wide volume range, allowing precise adjustment.

If the

MUTING

indicator is flashing on the AV receiver’s display, press the remote controller’s

MUTING

to unmute the AV receiver.

35

While a pair of headphones is connected to the

PHONES

jack, no sound is output from the speakers.

36

— If there’s no sound from a DVD player connected to an HDMI IN, check the DVD player’s output settings, and be sure to select a supported audio format.

Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

If your turntable uses an MC cartridge, you must connect an MC head amp, or an MC transformer.

Make sure that none of the connecting cables are bent, twisted, or damaged.

Not all listening modes use all speakers.

Specify the speaker distances and adjust the individual speaker levels.

28

43

If the input signal format is set to “

PCM

” or “

DTS

”.

Set it to “

Off

”.

46

En-57

Only the front speakers produce sound

When the Stereo or Mono listening mode is selected, only the front speakers and subwoofer produce sound.

Check the Speaker Configuration.

31

42

Only the center speaker produces sound

If you use the Dolby Pro Logic II Movie, Dolby Pro

Logic II Music, or Dolby Pro Logic II Game listening mode with a mono source, such as an AM radio station or mono TV program, the sound is concentrated in the center speaker.

Make sure the speakers are configured correctly.

42

The surround speakers produce no sound

When the T-D (Theater-Dimensional), Stereo or

Mono listening mode is selected, the surround speakers produce no sound.

Depending on the source and current listening mode, not much sound may be produced by the surround speakers. Try selecting another listening mode.

Make sure the speakers are configured correctly.

28

42

The center speaker produces no sound

When the Stereo or Mono listening mode is selected, the center speaker produces no sound.

Make sure the speakers are configured correctly.

42

The subwoofer produces no sound

When you play source material that contains no information in the LFE channel, the subwoofer produces no sound.

Make sure the speakers are configured correctly.

42

There’s no sound with a certain signal format

— Check the digital audio output setting on the connected device. On some game consoles, such as those that support DVD, the default setting is off.

With some DVD-Video discs, you need to select an audio output format from a menu.

Depending on the input signal, some listening modes cannot be selected.

28

-

32

Can’t get 5.1 playback

Depending on the number of connected speakers, it is not always possible to select all of the listening modes.

28

-

32

The speaker volume cannot be set as required

After the volume level of each individual speaker has been adjusted, the maximum volume may be reduced.

43

Noise can be heard

Using cable ties to bundle audio cables with power cords, speaker cables, and the like may degrade the audio performance, so refrain from doing it.

An audio cable may be picking up interference. Try repositioning your cables.

The Late Night function doesn’t work

Make sure the source material is Dolby Digital,

Dolby Digital Plus, and Dolby TrueHD.

38

About DTS signals

When DTS program material ends and the DTS bitstream stops, the AV receiver remains in DTS listening mode and the dts indicator remains on. This is to prevent noise when you use the pause, fast forward, or fast reverse function on your player. If you switch your player from DTS to PCM, because the AV receiver does not switch formats immediately, you may not hear any sound, in which case you should stop your player for about three seconds, and then resume playback.

Appendix

With some CD and LD players, you won’t be able to playback DTS material properly even though your player is connected to a digital input on the AV receiver. This is usually because the DTS bitstream has been processed (e.g., output level, sampling rate, or frequency response changed) and the AV receiver doesn’t recognize it as a genuine DTS signal. In such cases, you may hear noise.

Playing DTS program material, using the pause, fast forward, or fast reverse function on your player may produce a short audible noise. This is not a malfunction.

The beginning of audio received by an HDMI IN can’t be heard

— Since it takes longer to identify the format of an

HDMI signal than it does for other digital audio signals, audio output may not start immediately.

En-58

Video

There’s no picture

Make sure that all video connecting plugs are pushed in all the way.

13

Make sure that each video component is properly connected.

If the video source is connected to a component video input, you must assign that input to an input selector, and your TV must be connected to

COMPONENT

VIDEO OUT

.

14

,

15

15

,

41

If the video source is connected to a composite video input, your TV must be connected to the corresponding composite video output.

15

If the video source is connected to an HDMI input, you must assign that input to an input selector, and your TV must be connected to the

HDMI OUT

.

14

On your TV, make sure that the video input to which the AV receiver is connected is selected.

,

41

There’s no picture from a source connected to an HDMI IN

Reliable operation with an HDMI-to-DVI adapter is not guaranteed. In addition, video signals from a PC are not guaranteed.

69

The on-screen menus don’t appear

On your TV, make sure that the video input to which the AV receiver is connected is selected.

When the AV receiver is not connected to a TV via

HDMI OUT

, on-screen menus are not displayed.

Tuner

Reception is noisy, FM stereo reception is noisy, or the FM STEREO indicator doesn’t light

Relocate your antenna.

Move the AV receiver away from your TV or computer.

Listen to the station in mono.

When listening to an AM station, operating the remote controller may cause noise.

Passing cars and airplanes can cause interference.

Concrete walls weaken radio signals.

If nothing improves the reception, install an outdoor antenna.

26

Remote Controller

The remote controller doesn’t work

Before operating this unit, be sure to press

RECEIVER

.

Make sure that the batteries are installed with the correct polarity.

4

Install new batteries. Don’t mix different types of batteries, or old and new batteries.

Make sure that the remote controller is not too far away from the AV receiver, and that there’s no obstruction between the remote controller and the AV receiver’s remote control sensor.

4

4

— Make sure that the AV receiver is not subjected to direct sunshine or inverter-type fluorescent lights.

Relocate if necessary.

If the AV receiver is installed in a rack or cabinet with colored-glass doors, the remote controller may not work reliably when the doors are closed.

Make sure you’ve selected the correct remote controller mode.

10

,

54

When using the remote controller to control other manufacturers’ AV components, some buttons may not work as expected.

Appendix

Make sure you’ve entered the correct remote control code.

Make sure to set the same ID on both the AV receiver and remote controller.

53

46

Can’t control other components

If it’s an Onkyo component, make sure that the u cable and analog audio cable are connected properly.

Connecting only an u

cable won’t be enough.

16

10

,

54

Make sure you’ve selected the correct remote controller mode.

If you’ve connected an cassette tape deck to the

TV/CD IN

jack, or an RI Dock to the

TV/CD IN

or

GAME IN

jacks, for the remote controller to work properly, you must set the input display appropriately.

35

If you cannot operate it, you will need to enter the appropriate remote control code.

To control another manufacturer’s component, point the remote controller at that component.

53

53

To control an Onkyo component that’s connected via u , point the remote controller at the AV receiver.

Be sure to enter the appropriate remote control code first.

53

To control an Onkyo component that’s not connected via u

, point the remote controller at the component.

Be sure to enter the appropriate remote control code first.

54

The entered remote control code may not be correct.

If more than one code is listed, try each one.

RI Dock for iPod/iPhone

There’s no sound

Make sure your iPod/iPhone is actually playing.

Make sure your iPod/iPhone is properly inserted in the Dock.

Make sure the AV receiver is turned on, the correct input source is selected, and the volume is turned up.

Make sure the plugs are pushed in all the way.

Try resetting your iPod/iPhone.

En-59

There’s no video

Make sure that your iPod/iPhone model’s TV OUT setting is set to On.

Make sure the correct input is selected on your TV or the AV receiver.

Some versions of the iPod/iPhone do not output video.

The AV receiver’s remote controller doesn’t control my iPod/iPhone

Make sure your iPod/iPhone is properly inserted in the Dock. If your iPod/iPhone is in a case, it may not connect properly to the Dock. Always remove your iPod/iPhone from the case before inserting it into the

Dock.

— The iPod/iPhone cannot be operated while it’s displaying the Apple logo.

Make sure you’ve selected the right remote mode.

When you use the AV receiver’s remote controller, point it toward your AV receiver.

52

If you still can’t control your iPod/iPhone, start playback by pressing your iPod/iPhone model’s Play button. Remote operation should then be possible.

Try resetting your iPod/iPhone.

Depending on your iPod/iPhone, some buttons may not work as expected.

The AV receiver unexpectedly selects my iPod/iPhone as the input source

Always pause iPod/iPhone playback before selecting a different input source. If playback is not paused, the

Direct Change function may select your iPod/iPhone as the input source by mistake during the transition between tracks.

iPod/iPhone doesn’t work properly

Try reconnecting your iPod/iPhone.

Zone 2

There’s no sound

Only components connected to analog inputs can be played in Zone 2.

Music Server and Internet Radio

Can’t access the server or Internet radio

Check the network connection between the AV receiver and your router or switch.

Make sure that your modem and router are properly connected, and make sure they are both turned on.

Make sure the server is up and running and compatible with the AV receiver.

Check the “Network Setup”.

70

71

48

Playback stops while listening to music files on the server

Make sure your server is compatible with the AV receiver.

If you download or copy large files on your computer, playback may be interrupted. Try closing any unused programs, use a more powerful computer, or use a dedicated server.

71

If the server is serving large music files to several networked devices simultaneously, the network may become overloaded and playback may be interrupted.

Reduce the number of playback devices on the network, upgrade your network, or use a switch instead of a hub.

Can’t connect to the AV receiver from a Web browser

If you’re using DHCP, your router may not always allocate the same IP address to the AV receiver, so if you find that you can’t connect to a server or Internet radio station, recheck the AV receiver’s IP address on the “

Network Setup

” screen.

Check the “Network Setup”.

49

48

Appendix

USB Device Playback

Can’t access the music files on a USB device

Make sure the USB device is plugged in properly.

The AV receiver supports USB devices that support the USB mass storage device class. However, playback may not be possible with some USB devices even if they conform to the USB mass storage device class.

USB memory devices with security functions cannot be played.

71

En-60

Others

Standby power consumption

In the following cases, the power consumption in standby mode may reach up to a maximum of 4.2 W:

– The “

HDMI Ctrl (RIHD)

” setting is set to “

On

”.

(Depending on the TV status, the AV receiver will enter standby mode as usual.)

– The “

HDMI Through

” setting is set to other than

Off

”.

– The “

Network Standby

” setting is set to “

On

”.

47

,

49

The sound changes when I connect my headphones

When a pair of headphones is connected, the listening mode is set to Stereo, unless it’s already set to Stereo,

Mono, or Direct.

How do I change the language of a multiplex source

Use the “

Input Ch (Mux)

” setting in the “

Audio

Adjust

” menu to select “

Main

” or “

Sub

”.

44

The

u

functions don’t work

To use u

, you must make an u

connection and an analog audio connection (RCA) between the component and AV receiver, even if they are connected digitally.

16

While Zone 2 is selected, the work.

u functions don’t

16

The functions System On/Auto Power On and

Direct Change don’t work for components connected via

u

These functions don’t work when Zone 2 is turned on.

16

The following settings can be made for the composite video inputs

You must use the buttons on the unit to make these settings.

On the AV receiver, press the input selector for the input source that you want to set and the

SETUP

button simultaneously. While holding down the input selector button, press

SETUP

until “

Video ATT :On

” appears on the AV receiver’s display. Then, release both buttons.

To turn the setting off, repeat the above process so that

Video ATT :Off

” appears on the AV receiver’s display, and release the buttons.

• Video Attenuation

This setting can be made for the

BD/DVD

,

CBL/SAT

,

GAME

,

PC

,

AUX

or

USB

input.

If you have a game console connected to the composite video input, and the picture isn’t very clear, you can attenuate the gain.

Video ATT :Off:

(default).

Video ATT :On:

Gain is reduced by 2 dB.

If the picture on your TV/monitor connected to the HDMI OUT is unstable, try switching the

DeepColor function off

To turn off the DeepColor function, simultaneously press the

GAME

and 8

ON/STANDBY

buttons on the

AV receiver. While holding down

GAME

, press

8

ON/STANDBY

until “

Deep Color:Off

” appears on the AV receiver’s display. Then, release both buttons.

To reactivate the DeepColor function, repeat the above process until “

Deep Color:On

” appears on the AV receiver’s display and release the buttons.

Appendix

The AV receiver contains a microcomputer for signal processing and control functions. In very rare situations, severe interference, noise from an external source, or static electricity may cause it to lockup. In the unlikely event that this happens, unplug the power cord from the wall outlet, wait at least five seconds, and then plug it back in.

Onkyo is not responsible for damages (such as CD rental fees) due to unsuccessful recordings caused by the unit’s malfunction. Before you record important data, make sure that the material will be recorded correctly.

Before disconnecting the power cord from the wall outlet, set the AV receiver to standby.

En-61

Firmware Update

To update the firmware of the AV receiver, you can choose from the following two methods: update via network, or update via USB storage. Choose the one that best suits your environment. Before proceeding with the update, please read the corresponding explanations carefully.

Update via network

You need a wired Internet connection to update the firmware.

Update via USB storage (

page 64 )

Please prepare a USB storage device such as a USB flash memory stick. You need at least 32 MB of available space to update the firmware.

Note

• Check the network connection before updating.

• Do not touch any cable or device connected to the AV receiver during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• Do not shutdown the power of the AV receiver while it is being updated.

• The storage media in the USB card reader may not work.

• If the USB device is partitioned, each section will be treated as an independent device.

• If the USB device contains a lot of data, the AV receiver may take a while to read it.

• Operation is not guaranteed for all USB devices, which includes the ability to power them.

• Onkyo takes no responsibility whatsoever for the loss or damage of data resulting from the use of a USB device with the AV receiver. Onkyo recommends that you back up your important music files beforehand.

• If you connect a USB hard disk drive to the USB port, Onkyo recommends that you use its AC adapter to power it.

• USB hubs and USB devices with hub functions are not supported.

Do not connect your USB device via a USB hub.

• USB devices with security functions are not supported.

Limitation of liability

The program and accompanying online documentation are furnished to you for use at your own risk. Onkyo will not be liable and you will have no remedy for damages for any claim of any kind whatsoever concerning your use of the program or the accompanying online documentation, regardless of legal theory, and whether arising in tort or contract. In no event will Onkyo be liable to you or any third party for any special, indirect, incidental, or consequential damages of any kind, including, but not limited to, compensation, reimbursement or damages on account of the loss of present or prospective profits, loss of data, or for any other reason whatsoever.

See the Onkyo web site for latest information.

Appendix

Updating the Firmware via Network

The AV receiver allows you to update the firmware using network connection on the rear panel.

Note

• Make sure your AV receiver and TV are turned on and an

Ethernet cable is connected to the rear panel of the AV receiver.

• Never unplug or turn off the AV receiver while it is being updated.

• Never plug or unplug an HDMI or Ethernet cable during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• Never unplug the power cord during the update process.

• It takes up to 10 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is finished.

Before you start

• Set the “

HDMI Ctrl (RIHD)

” setting to “

Off

(

page 47

).

• Turn off the controller device connected via Ethernet cable.

• Turn off Multi Zone if this function is present.

• Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc.

To be continued

En-62

Update procedure

1

Press RECEIVER followed by HOME on the remote controller.

The Home menu appears on the TV screen.

2

Select “F/W Update” and press ENTER .

Note that the “

F/W Update

” option will be grayed out for a short while after the AV receiver is turned on.

Please wait until it becomes operable.

3

Select “Update via NET” and press ENTER .

Note that this option will not be available if there is no firmware file newer than the currently installed version.

4

Select “Update” and press ENTER .

The update process will begin.

During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the AV receiver’s display. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.

5

The message “Completed!” appears on the AV receiver’s display, indicating that the update has been completed.

6

Turn off the AV receiver using

8

ON/STANDBY on the front panel.

Do not use 8

RECEIVER

on the remote controller.

Once turned off, the AV receiver will automatically turn on again.

Congratulations! You now have the latest firmware installed on your Onkyo AV receiver.

Troubleshooting

Case 1:

If an error occurs, “

Error!! *-**

” is displayed on the AV receiver’s display. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

Errors during an update via network

Error Code Description

*

-10

,

*

-20

The Ethernet cable was not detected.

Reconnect the cable properly.

*

-11

,

*

-13

,

*

-21

,

*

-28

Others

Internet connection error.

Check the following items:

• Make sure the IP address, subnet mask, gateway address, and DNS server are configured properly.

• Make sure the router is turned on.

• Make sure the AV receiver and the router are connected with an Ethernet cable.

• Make sure your router is configured properly.

See the instruction manual of the router.

• If your network allows only one client connection and there is any other device already connected, the AV receiver will not be able to access the network. Consult your

Internet Service Provider (ISP).

• If your modem does not function as a router, you will need a router. Depending on your network, you may need to configure the proxy server if necessary. See the document provided by your ISP. If you are still unable to access the Internet, the DNS or proxy server may be temporarily down. Contact your ISP.

Retry the update procedure from the beginning.

If the error persists, please contact Onkyo

Support (

page 65

) and provide the error code.

Case 2:

If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

Appendix

Case 3:

If you do not have an Internet connection to the network, please contact Onkyo Support (

page 65

).

En-63

Updating the Firmware via USB

The AV receiver allows you to update the firmware using a

USB device.

Note

• Never unplug or turn off the AV receiver during the update process.

• Never plug or unplug an HDMI cable or a USB device during the update process.

• Never unplug the USB storage device containing the firmware file or the AC power cord during the update process.

• Do not attempt to access the AV receiver from your PC while it is being updated.

• It takes up to 10 minutes to complete the firmware update.

• The AV receiver will retain all your settings after the update is finished.

Before you start

• Set the “

HDMI Ctrl (RIHD)

” setting to “

Off

(

page 47

).

• Turn off the controller device connected via Ethernet cable.

• Turn off Multi Zone if this function is present.

• Stop playback of contents from Internet Radio, iPod/iPhone, USB or servers, etc.

• If there is any data in the USB device, remove it first.

Update procedure

1

Connect a USB device to your PC. If there is any data in the USB device, remove it first.

2

Download the firmware file from the Onkyo web site. The file name is as follows:

ONKAVR****_************.zip

Unzip the downloaded file. The following three files are created:

ONKAVR****_************.of1

ONKAVR****_************.of2

ONKAVR****_************.of3

3

Copy the extracted files to the USB device. Be careful not to copy the zip file.

4

Remove the USB device from your PC and connect it to the

USB

port on the AV receiver.

5

Make sure the AV receiver and TV are turned on.

If the AV receiver is in standby mode, press

8

ON/STANDBY

on the AV receiver to light up the front display.

6

Select the USB input source.

Now Initializing...

” appears on the AV receiver’s display and then the name of the USB device is displayed. It takes 20 to 30 seconds to recognize the

USB device.

7

Press RECEIVER followed by HOME on the remote controller.

The Home menu appears on the TV screen.

8

Select “F/W Update” and press ENTER .

Appendix

9

Select “Update via USB” and press ENTER .

Note that this option will not be available if there is no firmware file newer than the currently installed version.

10

Select “Update” and press ENTER .

The update process will begin.

During the update process, the on-screen display may disappear depending on the updated program. When this occurs, you can still view the update progress on the AV receiver’s display. The on-screen display will reappear after the update is complete, and upon turning the AV receiver off and on again.

Do not turn off the AV receiver and do not remove the

USB device during the update process.

11

The message “Completed!” appears on the AV receiver’s display, indicating that the update has been completed.

Remove the USB device.

12

Turn off the AV receiver using

8

ON/STANDBY on the front panel.

Do not use

8

RECEIVER

on the remote controller.

Once turned off, the AV receiver will automatically turn on again.

Congratulations! You now have the latest firmware installed on your Onkyo AV receiver.

En-64

Troubleshooting

Case 1:

If an error occurs, “

Error!! *-**

” is displayed on the AV receiver’s display. (Alpha-numeric characters on the front display are denoted by asterisks.) Refer to the following table and take appropriate action.

Errors during an update via USB

Error Code

*

-10

,

*

-20

*

-14

Others

Description

The USB device was not detected. Make sure the USB flash memory or USB cable is properly connected to the USB port. If the USB storage device has its own power supply, use it to power the USB device.

The firmware file was not found in the root folder of the USB device, or the firmware file is for another model. Retry and download the file on the support page of the web site, following the on-site instructions. If the error persists, please contact Onkyo Support and provide the error code.

Retry the update procedure from the beginning.

If the error persists, please contact Onkyo

Support and provide the error code.

Case 2:

If an error occurs during the update process, disconnect then reconnect the AC power cord and try again.

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN http://www.onkyo.com/

The Americas

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

For Dealer, Service, Order and all other Business Inquiries:

Tel: 201-785-2600

Fax: 201-785-2650

Hours:M-F 9am-5pm ET http://www.us.onkyo.com/

For Product Support Team Only:

1-800-229-1687

Hours:M-F 9am-8pm / Sat-Sun 10am-8pm ET http://www.us.onkyo.com/

Europe

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

China, Hong Kong

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim

Sha Tsui Kowloon, Hong Kong.

Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com

Asia, Oceania, Middle East, Africa

Please contact an Onkyo distributor referring to Onkyo

SUPPORT site.

http://www.intl.onkyo.com/support/firmware/index.html

The above-mentioned information is subject to change without prior notice. Visit the Onkyo web site for the latest update.

En-65

Appendix

Connection Tips and

Video Signal Path

The AV receiver supports several connection formats for compatibility with a wide range of AV equipment. The format you choose will depend on the formats supported by your components. Use the following sections as a guide.

The on-screen menus appear only on a TV that is connected to the

HDMI OUT

. If your TV is connected to other video outputs, use the AV receiver’s display when changing settings.

Note

• The on-screen menus are displayed when:

– There is no video input, or

– The video input is 480p, 720p, 1080i, or 1080p.

Video Connection Formats

Video components can be connected by using any one of the following video connection formats: composite video, component video, or HDMI, the latter offering the best picture quality.

When choosing a connection format, bear in mind that the

AV receiver doesn’t convert between formats, so only outputs of the same format as the input will output the signal.

Video Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Composite Component

IN

HDMI

AV receiver

MONITOR OUT

Component Composite HDMI

TV, projector, etc.

Appendix

Audio Connection Formats

Audio components can be connected by using any of the following audio connection formats: analog, optical, coaxial, or HDMI.

When choosing a connection format, bear in mind that the

AV receiver does not convert digital input signals for analog line outputs and vice versa.

If signals are present at more than one input, the inputs will be selected automatically in the following order of priority:

HDMI, digital, analog.

Audio Signal Flow Chart

Blu-ray Disc/DVD player, etc.

Analog Optical

*1

IN

Coaxial

*1

HDMI

AV receiver

*1

OUT

*1

HDMI

*2

TV, projector, etc.

*1

*2

Depends on the “

Audio TV Out

” setting (

page 47

).

This is possible when “

Audio Return Ch

” is set to “

Auto

(

page 48

), the

TV/CD

input selector is selected, and your

TV is ARC capable.

Tip

• When a signal is input via HDMI and the corresponding input selector is selected, the

HDMI

indicator lights. In the case of an optical or coaxial connection, the

DIGITAL

indicator lights. In the case of an analog connection, neither of the

HDMI

and

DIGITAL

indicators light.

En-66

Using an RIHDcompatible TV, Player, or Recorder

p

, which stands for Remote Interactive over

HDMI, is the name of the system control function found on

Onkyo components. The AV receiver can be used with

CEC (Consumer Electronics Control), which allows system control over HDMI and is part of the HDMI standard. CEC provides interoperability between various components, however, operation with components other than p

-compatible components cannot be guaranteed.

About

p

-compatible components

The following components are p

-compatible (As of January 2012).

TV

• Toshiba TV

• Sharp TV

Players/Recorders

• Onkyo and Integra p -compatible players

• Toshiba players and recorders

• Sharp players and recorders (only when used together with Sharp TV)

*

Models other than those mentioned above may have some interoperability if compatible with CEC, which is part of the

HDMI Standard, but operation cannot be guaranteed.

Note

• For proper linked operations, do not connect more p

compatible components than the quantities specified below, to the HDMI input terminal.

– Blu-ray Disc/DVD players: up to three.

– Blu-ray Disc/DVD recorders/Digital Video Recorders: up to three.

– Cable/Satellite Set-top boxes: up to four.

• Do not connect the AV receiver to another AV receiver/AV amplifier via HDMI.

• Proper linked operations are not guaranteed when more p -compatible components than the above-mentioned quantities are connected.

Appendix

Operations that can be performed with

p

connection

For

p

-compatible TV

The following linked operations are enabled by connecting the AV receiver to an p

-compatible TV.

• The AV receiver will enter standby mode when the power of the TV is turned to standby.

• You can set on the menu screen of the TV to either output the audio from the speakers connected to the AV receiver, or from the speakers of the TV.

• It is possible to output the video/audio coming from the antenna or from the input jack of the TV from the speakers connected to the AV receiver. (A connection such as optical digital cable or similar is required in addition to the HDMI cable.)

• Input to the AV receiver can be selected with the remote controller of the TV.

• Operations such as volume adjustment or similar for the

AV receiver can be performed from the remote controller of the TV.

For

p

-compatible players/recorders

The following linked operations are enabled by connecting the AV receiver to an p -compatible player/recorder.

• When playback is started on the player/recorder, AV receiver will switch to the HDMI input of the player/recorder that is playing back.

• Operation of the player/recorder is possible using the remote controller supplied with the AV receiver.

* Depending on the model used, not all operations may be available.

To be continued

En-67

How to connect and setup

1

Confirm the connection and settings.

1. Connect the

HDMI OUT

jack to the HDMI input jack of the TV.

Blu-ray Disc/DVD player, etc.

DIGITAL AUDIO connection

(OPTICAL)

HDMI connection

AV receiver

HDMI connection

TV, projector, etc.

2. Connect the audio output from the TV to the

OPTICAL IN 2

jack of the AV receiver using an optical digital cable.

Note

• When the audio return channel (ARC) function is used with an ARC capable TV, this connection is not necessary

(

page 48

).

3. Connect the HDMI output of the Blu-ray

Disc/DVD player/recorder to the

HDMI IN 1

jack of the AV receiver.

Note

• It is necessary to assign the HDMI input when connecting the Blu-ray Disc/DVD player/recorder to other jacks

(

page 41

). Do not assign the components connected to the HDMI IN to the TV/CD input at this time. Appropriate

CEC (Consumer Electronics Control) operation can not be guaranteed.

2

Change each item in the “HDMI Setup” menu according to the following settings:

HDMI Ctrl (RIHD)

:

On

Audio Return Ch

(ARC):

Auto

See details of each setting (

pages 47

,

48

).

3

Confirm the settings.

1. Turn on the power for all connected components.

2. Turn off the power of the TV, and confirm that the power of the connected components is turned off automatically with the link operation.

3. Turn on the power of the Blu-ray Disc/DVD player/recorder.

4. Start playback on the Blu-ray Disc/DVD player/recorder, and verify the following:

• The AV receiver automatically turns on, and selects the input to which the Blu-ray

Disc/DVD player/recorder is connected.

• The TV automatically turns on, and selects the input to which the AV receiver is connected.

5. Following the operating instructions of the TV, select “Use the TV speakers” from the menu screen of the TV, and confirm that the audio is output from the speakers of the TV, and not from the speakers connected to the AV receiver.

6. Select “Use the speakers connected from the AV receiver” from the menu screen of the TV, and confirm that the audio is output from the speakers connected to the AV receiver, and not from the

TV speakers.

Note

• Perform the above operations when you use the AV receiver for the first time, when the settings of each component are changed, when the main power of each component is turned off, when the power cable is disconnected from the power supply, or when there has been a power outage.

Appendix

4

Operate with the remote controller.

For buttons that can be operated (

page 55

).

Note

• Audio from DVD-Audio or Super Audio CD may not output from the TV speakers. You will be able to output the audio from the TV speakers by setting the audio output of the

DVD player to 2ch PCM. (It may not be possible depending on the player models.)

• Even if you set to output audio on the TV speakers, audio will be output from the speakers connected to the AV receiver when you adjust the volume or switch the input on the AV receiver. To output audio from the TV speakers, redo the corresponding operations on the TV.

• In case of an p connection with u and u audio control compatible components, do not connect the u cable at the same time.

• On the TV, when you select anything other than the HDMI jack to which the AV receiver is connected, the input on the

AV receiver will be switched to “

TV/CD

”.

• The AV receiver will automatically power on in conjunction when it determines it to be necessary. Even if the AV receiver is connected to an p

compatible TV or player/recorder, it will not power on if it is not necessary. It may not power on in conjunction when the TV is set to output audio from the TV.

• Linked functions with the AV receiver may not work depending on the component model connected. In such cases, operate the AV receiver directly.

En-68

About HDMI

Designed to meet the increased demands of digital TV,

HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors,

Blu-ray Disc players/DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components. With HDMI, a single cable can carry control signals, digital video, and up to eight channels of digital audio (2-channel PCM, multichannel digital audio, and multichannel PCM).

The HDMI video stream (i.e., video signal) is compatible with DVI (Digital Visual Interface)

*1

, so TVs and displays with a DVI input can be connected by using an HDMI-to-

DVI adapter cable. (This may not work with some TVs and displays, resulting in no picture.)

The AV receiver uses HDCP (High-bandwidth Digital

Content Protection)

*2

, so only HDCP-compatible components can display the picture.

Supported Audio Formats

• 2-channel linear PCM (32–192 kHz, 16/20/24 bit)

• Multichannel linear PCM (up to 7.1 ch, 32–192 kHz,

16/20/24 bit)

• Bitstream (DSD, Dolby Digital, Dolby Digital Plus,

Dolby TrueHD, DTS, DTS-HD High Resolution Audio,

DTS-HD Master Audio)

Your Blu-ray Disc player/DVD player must also support

HDMI output of the above audio formats.

The AV receiver’s HDMI interface is based on the following:

Audio Return Channel, 3D, x.v.Color, DeepColor, Lip

Sync, DTS-HD Master Audio, DTS-HD High

Resolution Audio, Dolby TrueHD, Dolby Digital Plus,

DSD and Multichannel PCM.

Appendix

About Copyright Protection

The AV receiver supports HDCP (High-bandwidth Digital

Content Protection)

*2

, a copy-protection system for digital video signals. Other devices connected to the AV receiver via HDMI must also support HDCP.

*1

*2

*3

DVI (Digital Visual Interface): The digital display interface standard set by the DDWG *3 in 1999.

HDCP (High-bandwidth Digital Content Protection): The video encryption technology developed by Intel for

HDMI/DVI. It’s designed to protect video content and requires a HDCP-compatible device to display the encrypted video.

DDWG (Digital Display Working Group): Lead by Intel,

Compaq, Fujitsu, Hewlett Packard, IBM, NEC, and Silicon

Image, this open industry group’s objective is to address the industry’s requirements for a digital connectivity specification for high-performance PCs and digital displays.

Note

• The HDMI video stream is compatible with DVI (Digital Visual

Interface), so TVs and displays with a DVI input can be connected by using an HDMI-to-DVI adapter cable. (Note that

DVI connections only carry video, so you’ll need to make a separate connection for audio.) However, reliable operation with such an adapter is not guaranteed. In addition, video signals from a PC are not supported.

• The HDMI audio signal (sampling rate, bit length, etc.) may be restricted by the connected source component. If the picture is poor or there’s no sound from a component connected via HDMI, check its setup. Refer to the connected component’s instruction manual for details.

En-69

Network/USB Features

Connecting to the Network

The following diagram shows how you can connect the AV receiver to your home network. In this example, it’s connected to a LAN port on a router, which has a 4-port

100Base-TX switch built-in.

Internet radio

Modem

Computer or media server

WAN

LAN

Router

Network Requirements

Ethernet Network

For the best results, a 100Base-TX switched Ethernet network is recommended. Although it’s possible to play music on a computer that’s connected to the network wirelessly, playback may be unreliable, so it is recommended to use wired connections.

Ethernet Router

A router manages the network, data-routing and supplying of IP addresses. Your router must support the following:

• NAT (Network Address Translation). NAT allows several networked computers to access the Internet simultaneously via a single Internet connection. The AV receiver needs Internet access for Internet radio.

• DHCP (Dynamic Host Configuration Protocol). DHCP supplies IP addresses to the network devices, allowing them to configure themselves automatically.

• A router with a built-in 100Base-TX switch is recommended.

Some routers have a built-in modem, and some Internet

Service Providers (ISP) require you to use specific routers.

Please consult your ISP or computer dealer if you’re unsure.

CAT5 Ethernet cable

Use a shielded CAT5 Ethernet cable (straight-type) to connect the AV receiver to your home network.

Internet Access (for Internet radio)

To receive Internet radio, your Ethernet network must have

Internet access. A narrowband Internet connection (e.g.,

56K modem, ISDN) will not provide satisfactory results, so a broadband connection is strongly recommended (e.g., cable modem, xDSL modem, etc). Please consult your ISP or computer dealer if you’re unsure.

Note

• To receive Internet radio with the AV receiver, your broadband

Internet connection must be working and able to access the Web.

Appendix

Consult your ISP if you have any problems with your Internet connection.

• The AV receiver uses DHCP to configure its network settings automatically. If you want to configure these settings manually, see “Network Setup” (

page 48

).

• The AV receiver does not support PPPoE settings, so if you have a PPPoE-type Internet connection, you must use a PPPoEcompatible router.

• Depending on your ISP, you may need to specify a proxy server to use Internet radio. If your computer is configured to use a proxy server, use the same settings for the AV receiver

(

page 49

).

En-70

Server Requirements

Server playback

The AV receiver can play digital music files stored on a computer or media server and supports the following technologies:

• Windows Media Player 11

• Windows Media Player 12

• Windows Media Connect 2.0

• DLNA-certified media server

If the operating system of your computer is Windows

Vista, Windows Media Player 11 is already installed.

Windows Media Player 11 for Windows XP can be downloaded for free from the Microsoft web site.

• The computer or media server must be on the same network as the AV receiver.

• Up to 20,000 folders can be displayed, and folders may be nested up to 16 levels deep.

Note

• Depending on the media server, the AV receiver may not recognize it, or may not be able to play its music files.

Minimum system requirements for Windows Media

Player 11 on Windows XP

Operating system

Windows XP Home Edition (SP2), Windows XP

Professional (SP2), Windows XP Tablet PC Edition

(SP2), Update Rollup 2 for Windows XP Media Center

Edition 2005 (KB900325), October 2006 Update Rollup for Windows XP Media Center Edition (KB925766)

Processor:

Memory:

233 MHz Intel Pentium II, Advanced

Micro Devices (AMD), etc.

64 MB

Hard disk:

Drive:

200 MB of free space

CD or DVD drive

Modem:

28.8 kbps

Sound card:

16-bit sound card

Monitor:

Super VGA (800 x 600)

Video card:

Software:

64 MB VRAM, DirectX 9.0b

Microsoft ActiveSync (only when using a Windows Mobile-based Pocket

PC or smartphone)

Web browser:

Microsoft Internet Explorer 6 or

Netscape 7.1

Remote playback

• Windows Media Player 12

• DLNA-certified (within DLNA Interoperability

Guidelines version 1.5) media server or controller device.

Setting varies depending on the device. Refer to your device’s instruction manual for details.

If the operating system of your personal computer is

Windows 7, Windows Media Player 12 is already installed.

For more information, see the Microsoft web site.

Appendix

USB Device Requirements

• USB mass storage device class (but not always guaranteed).

• FAT16 or FAT32 file system format.

• If the storage device has been partitioned, each section will be treated as an independent device.

• Up to 20,000 folders can be displayed, and folders may be nested up to 16 levels deep.

• USB hubs and USB devices with hub functions are not supported.

Note

• If the media you connect is not supported, the message “

No

Storage

” will be displayed.

• If you connect a USB hard disk drive to the AV receiver’s

USB

port, we recommend that you use its AC adapter to power it.

• The AV receiver supports USB MP3 players that support the

USB Mass Storage Class standard, which allows USB devices to be connected to computers without the need for special drivers or software. Note that not all USB MP3 players support the USB

Mass Storage Class standard. Refer to your USB MP3 player’s instruction manual for details.

• Protected WMA music files on an MP3 player cannot be played.

• Onkyo accepts no responsibility whatsoever for the loss or damage to data stored on a USB device when that device is used with the AV receiver. We recommend that you back up your important music files beforehand.

• MP3 players containing music files that are managed with special music software are not supported.

• Operation is not guaranteed for all USB devices, which includes the ability to power them.

• Do not connect your USB device via a USB hub. The USB device must be connected directly to the AV receiver’s

USB

port.

• If the USB device contains a lot of data, the AV receiver make take a while to read it.

• USB devices with security functions cannot be played.

En-71

Supported Audio File Formats

For server playback and playback from a USB device, the

AV receiver supports the following music file formats.

Variable bit-rate (VBR) files are supported. However, playback times may not display correctly.

Note

• With remote playback, the AV receiver does not support the following music file formats: FLAC and Ogg Vorbis.

• In the case of server playback, the above-mentioned file formats may not be played depending on the server type.

MP3 (.mp3 or .MP3)

• MP3 files must be MPEG-1/MPEG-2 Audio Layer 3 format with a sampling rate of 8 kHz, 11.025 kHz,

12 kHz, 16 kHz, 22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz,

48 kHz and bitrates of between 8 kbps and 320 kbps.

Incompatible files cannot be played.

WMA (.wma or .WMA)

WMA stands for Windows Media Audio and is an audio compression technology developed by Microsoft

Corporation. Audio can be encoded in WMA format by using Windows Media ® Player.

• WMA files must have the copyright option turned off.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, bitrates of between 5 kbps and 320 kbps, and WMA DRM are supported.

• WMA Pro/Voice formats are not supported.

WMA Lossless (.wma or .WMA)

• Sampling rates of 44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz are supported.

• Quantization bit: 16 bit, 24 bit

WAV (.wav or .WAV)

WAV files contain uncompressed PCM digital audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

AAC

(.aac/.m4a/.mp4/.3gp/.3g2/.AAC/.M4A/.MP4/

.3GP or .3G2)

AAC stands for MPEG-2/MPEG-4 Audio.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, 96 kHz and bitrates of between 8 kbps and

320 kbps are supported.

FLAC (.flac or .FLAC)

FLAC is a file format for lossless audio data compression.

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz, 96 kHz, 176.4 kHz and 192 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

Ogg Vorbis (.ogg or .OGG)

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz and bitrates of between 48 kbps and 500 kbps are supported.

Incompatible files cannot be played.

LPCM (Linear PCM)

• Sampling rates of 8 kHz, 11.025 kHz, 12 kHz, 16 kHz,

22.05 kHz, 24 kHz, 32 kHz, 44.1 kHz, 48 kHz, 64 kHz,

88.2 kHz and 96 kHz are supported.

• Quantization bit: 8 bit, 16 bit, 24 bit

*

Only for playback via network.

Appendix

About DLNA

The Digital Living Network Alliance is an international, cross-industry collaboration. Members of DLNA develop a concept of wired and wireless interoperable networks where digital content such as photos, music, and videos can be shared through consumer electronics, personal computers, and mobile devices in and beyond the home.

The AV receiver complies with the DLNA Interoperability

Guidelines version 1.5.

En-72

License and Trademark

Information

“x.v.Color” is a trademark of Sony Corporation.

Manufactured under license under U.S. Patent Nos: 5,956,674;

5,974,380; 6,226,616; 6,487,535; 7,212,872; 7,333,929;

7,392,195; 7,272,567 & other U.S. and worldwide patents issued

& pending. DTS-HD, the Symbol, & DTS-HD and the Symbol together are registered trademarks of DTS, Inc. Product includes software. © DTS, Inc. All Rights Reserved.

Manufactured under license from Dolby Laboratories. Dolby,

Pro Logic and the double-D symbol are trademarks of Dolby

Laboratories.

Music Optimizer™ is a trademark of Onkyo Corporation.

“HDMI, the HDMI Logo, and High-Definition Multimedia

Interface are trademarks or registered trademarks of

HDMI Licensing LLC in the United States and other countries.” iPhone, iPod, iPod classic, iPod nano, iPod shuffle, and iPod touch are trademarks of Apple Inc., registered in the U.S. and other countries.

“Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards.

Please note that the use of this accessory with iPod or iPhone may affect wireless performance.

Apple TV is a trademark of Apple Inc., registered in the U.S. and other countries.

“DLNA ® , the DLNA Logo and DLNA CERTIFIED™ are trademarks, service marks, or certification marks of the Digital

Living Network Alliance.”

Windows and the Windows logo are trademarks of the Microsoft group of companies.

InstaPrevue and the InstaPrevue logo are trademarks or registered trademarks of Silicon Image, Inc. in the United States and other countries.

En-73

Appendix

Specifications

Amplifier Section

Rated Output Power

All channels: 80 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.7% (FTC)

Dynamic Power

*

* IEC60268-Short-term maximum output power

180 W (3

, Front)

160 W (4

, Front)

100 W (8

, Front)

THD+N (Total Harmonic Distortion+Noise)

Damping Factor

0.08% (20 Hz - 20 kHz, half power)

60 (Front, 1 kHz, 8

)

Input Sensitivity and Impedance (Unbalance)

200 mV/47 k

(LINE)

Rated RCA Output Level and Impedance

200 mV/2.2 k

(LINE OUT)

Maximum RCA Output Level and Impedance

2 V/2.2 k

(LINE OUT)

Frequency Response

5 Hz - 100 kHz/+1 dB, –3 dB (DSP bypass)

Tone Control Characteristics

±10 dB, 50 Hz (BASS)

±10 dB, 20 kHz (TREBLE)

Signal to Noise Ratio

100 dB (LINE, IHF-A)

Speaker Impedance

6

- 16

Video Section

Input Sensitivity/Output Level and Impedance

1 Vp-p/75

(Component Y)

0.7 Vp-p/75

(Component P

B

/C

B

, P

R

/C

R

)

1 Vp-p/75

(Composite

)

Component Video Frequency Response

5 Hz - 100 MHz/+0 dB, –3 dB

Tuner Section

FM Tuning Frequency Range

87.5 MHz - 107.9 MHz

AM Tuning Frequency Range

530 kHz - 1710 kHz

Preset Channel

40

General

Power Supply

AC 120 V, 60 Hz

Power Consumption

4.2 A

No-sound Power Consumption

55 W

Stand-by Power Consumption

Dimensions (W × H × D)

0.1 W

Weight

435 mm × 173.5 mm × 328 mm

17-1/8" × 6-13/16" × 12-15/16"

8.6 kg (19.0 lbs.)

HDMI

Input

Output

Video Resolution

Audio Format

Supported

IN 1, IN 2, IN 3, IN 4, IN 5, IN 6

OUT

1080p

Dolby TrueHD, DTS-HD Master Audio,

DVD-Audio, DSD

3D, Audio Return Channel, DeepColor, x.v.Color, LipSync, CEC (RIHD)

Video Inputs

Component

Composite

Video Outputs

IN 1, IN 2

BD/DVD, CBL/SAT, GAME, PC, AUX

Component

Composite

OUT

MONITOR OUT

Appendix

Audio Inputs

Digital

Analog

Audio Outputs

Optical: 2

Coaxial: 2

BD/DVD, CBL/SAT, GAME, PC, TV/CD,

AUX

Analog

ZONE2 LINE OUT

Subwoofer Pre Output

1

Speaker Outputs

Phones

Main (L, R, C, SL, SR)

1 (6.3 ø)

Others

RI

USB

Ethernet

1

1 (Front)

1

Specifications and features are subject to change without notice.

En-74

Memo

Appendix

En-75

2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN

Tel: 072-831-8023 Fax: 072-831-8163 http://www.onkyo.com/

18 Park Way, Upper Saddle River, N.J. 07458, U.S.A.

Tel: 800-229-1687, 201-785-2600 Fax: 201-785-2650 http://www.us.onkyo.com/

Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY

Tel: +49-8142-4401-0 Fax: +49-8142-4208-213 http://www.eu.onkyo.com/

The Coach House 81A High Street, Marlow, Buckinghamshire, SL7 1AB, UK

Tel: +44-(0)1628-473-350 Fax: +44-(0)1628-401-700

Unit 1033, 10/F, Star House, No 3, Salisbury Road, Tsim Sha Tsui Kowloon, Hong Kong.

Tel: 852-2429-3118 Fax: 852-2428-9039 http://www.onkyochina.com/

1301, 555 Tower, No.555 West NanJin Road, Jin an, Shanghai,

China 200041, Tel: 86-21-52131366 Fax: 86-21-52130396 http://www.cn.onkyo.com/

SN 29401316EN

(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

Y1205-1

* 2 9 4 0 1 3 1 6 E N *

Using Internet Radio

Using Internet Radio

Common Procedures in Internet Radio

Menu

Note

• Available services may vary depending on the region.

1

Press NET .

A list of the network services appears, and the

NET

indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

2

Select the desired service and press ENTER .

The top page of the selected service appears.

Using Multiple Accounts

The AV receiver supports multiple user accounts, which means you can freely switch between several logins.

After registering user accounts, login is performed from the “

Users

” screen.

1

Press MENU while the Users screen is displayed.

The following menu items appear:

Add new user

:

Remove this user

:

You can either store a new user account, or delete an existing one.

Tip

• Some of the services don’t allow the use of multiple user accounts.

• You can store up to 10 user accounts.

• To switch between accounts you must first log out from the current account, and log in again on the “

Users

” screen.

Pandora ® internet radio –Getting Started

(U.S. only) ................................................. 2

Using Rhapsody (U.S. only).......................... 3

Using the SiriusXM Internet Radio (North

American only) ......................................... 4

Using Last.fm Internet Radio ........................ 5

Using Slacker Personal Radio ...................... 6

Using MP3tunes ............................................. 7

En-1

Pandora

®

internet radio

–Getting Started (U.S. only)

Pandora is a free, personalized Internet radio service that plays the music you know and helps you discover music you’ll love.

1

Use

q

/

w

to select “I have a Pandora Account” or

“I’m new to Pandora” and then press ENTER .

If you are new to Pandora select “

I’m new to

Pandora

”. You will see an activation code on your

TV screen. Please write down this code. Go to an

Internet connected computer and point your browser to

www.pandora.com/onkyo

Enter your activation code and then follow the instructions to create your Pandora account and your personalized Pandora Internet radio stations. You can create your stations by entering your favorite songs and artists when prompted. After you have created your account and stations you can return to your

Onkyo receiver and press enter to begin listening to your personalized Pandora Internet radio.

If you have an existing Pandora account, you can add your Pandora account to your Onkyo receiver by selecting “

I have a Pandora Account

” and logging in with your email and password.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

2

To play a station, use

q

/

w

to select the station from your station list, and then press

ENTER

.

Playback starts and the playback screen appears.

Create a New Station:

Enter the name of a song, artist, or genre and Pandora will create a unique radio station for you based on the musical qualities of that song, artist, or genre.

Menu Items

I like this song:

Give a song “thumbs-up” and Pandora will play more music like it.

I don’t like this song:

Give a song “thumbs-down” and Pandora will ban that song from the current station.

Why is this song playing?:

Discover some of the musical attributes that Pandora uses to create your personal radio stations.

Don’t play the song for a month:

If you are tired of a song, you can put the song to sleep and Pandora will not play it for one month.

Create station from this artist:

Creates a radio station from this artist.

Using Internet Radio

Delete this station:

This will permanently delete a station from your

Pandora account. All of your thumbs feedback will be lost should you choose to re-create the station with the same song or artist.

Create station from this song:

Creates a radio station from this song.

Rename this station:

Lets you rename the current radio station.

Bookmark this artist:

Pandora will bookmark your favorite artist for your profile on

www.pandora.com

.

Bookmark this song:

Pandora will bookmark the current song and allow you to buy them all from Amazon or iTunes in one step!

Add to My Favorites:

Adds a station to My Favorites list.

PANDORA, the PANDORA logo, and the Pandora trade dress are trademarks or registered trademarks of Pandora

Media, Inc. Used with permission.

En-2

Using Rhapsody (U.S. only)

1

Use

q

/

w

to select “Sign in to your account” and then press

ENTER

.

To use Rhapsody, you need an account. If you don’t have one yet, you can create a new account at

www.rhapsody.com/onkyo

If you have an existing Rhapsody account, select

Sign in to your account

” and press

ENTER

.

Enter your user name (usually your email) and password in the next keyboard screen, or in Web

Setup.

Using the keyboard screen

1. Use q / w / e / r and

ENTER

to enter your user name and password.

2. Select “

OK

”.

3. Press

ENTER

. The “

Confirm your entries

” screen appears.

4. Press

ENTER

.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

2

Use

q

/

w

to select the menu, then press ENTER .

Search:

You can search for music by Artist, Album, or Track.

Music Guide:

You can play tracks from Genres, Top Artists, Top

Albums, Top Tracks, New Releases, and Staff Picks.

Rhapsody Channels:

Listen to radio channels programmed by Rhapsody’s top-notch editors.

Playlists:

Play your own personal playlists.

My Library:

Bookmark your favorite albums and tracks from the

Rhapsody catalog using My Library.

Account Info:

Confirm your account information.

Sign Out:

Sign out from your Rhapsody account.

Using Internet Radio

3

Use

q

/

w

to select a channel, and press ENTER or

1

to start playback.

Playback starts and the playback screen appears.

You can control the tracks with the buttons on the remote control.

Enabled buttons:

1

,

3

,

2

,

5

,

4

,

7

,

6

,

RANDOM

,

REPEAT

Note

• On Rhapsody Channels, some of the buttons don’t work.

Menu Items

Add track to My Library:

Bookmark currently-playing tracks.

Add album to My Library:

Bookmark currently-playing albums.

Add playlist to My Library:

Bookmark currently-playing playlists.

Add channel to My Channels:

Bookmark currently-playing Rhapsody radio channels.

Add to My Favorites:

Adds a track, channel or playlist to My Favorites list.

Tip

• You can remove bookmarked tracks, albums, and Rhapsody

Channels from My Library.

En-3

Using the SiriusXM Internet Radio

(North American only)

Your Onkyo AV receiver includes a free trial of SiriusXM

Internet Radio. The “Account Info” screen shows how many days are left in your trial. After the trial period expires, if you want to continue listening to the service, you must subscribe. To subscribe go to

www.siriusxm.com/internetradio

with your computer.

When you subscribe, you will be provided with a username and password which has to be entered into the AV receiver.

To use SiriusXM Internet Radio, you must have your AV receiver connected to the Internet. Using the remote control, follow these steps:

Using Internet Radio

1

Use

q

/

w

to select “Sign In”, and then press ENTER .

If you have an existing SIRIUS account, you can sign in by selecting “

Sign In

”. Enter your user name and password in the next keyboard screen, or in Web

Setup. If you don’t know your username or password, call Sirius XM at (888) 539-7474 for assistance.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

Using the keyboard screen

1. Use q

/ w

/ e

/ r

and

ENTER

to enter your user name and password.

2. Select “

OK

”.

3. Press

ENTER

. The “

Confirm your entries

” screen appears.

4. Press

ENTER

.

Please wait...

” appears and then “

SiriusXM

Internet Radio

” screen appears which displays the category available for selection.

2

Use

q

/

w

to select the category and then press

ENTER .

The channel list screen for the selected category appears.

3

Use

q

/

w

to select the desired channel and then press

ENTER .

The playback screen for the selected channel appears and you can listen to SiriusXM Internet Radio.

You can control the tracks with the buttons on the remote control.

Enabled buttons:

2

,

3

,

7

,

6

Menu Items

Add to My Favorites:

Adds a channel to My Favorites list.

SiriusXM Internet Radio subscriptions are sold separately and are governed by the Sirius Terms and Conditions (see www.sirius.com). Be sure to read this agreement before you purchase your subscription. Sirius, XM and all related marks and logos are trademarks of Sirius XM Radio Inc. and its subsidiaries. All rights reserved.

En-4

Using Last.fm Internet Radio

Last.fm is a music service that learns what you love...

Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see what they like, too.

With thousands of biographies, reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join

Get a subscription and you can enjoy the best of ad-free

Last.fm Radio on your Onkyo AV receiver without a computer!

Recommended Radio:

Discover smart personalised recommendations that adapt as your tastes change.

Artist Radio:

Pick any artist and we’ll play you a whole station of music inspired by your choice.

My Library:

Sit back and enjoy selections from all the music you’ve heard since you joined Last.fm.

Tag Radio:

Polish funk? Death pop? Think of a style and we’ll entertain you with it for hours.

Start your free trial straight away when you create your account and see for yourself what it’s like to have the world’s music at your fingertips. Latest prices and full information are available at www.last.fm/subscribe

1

Use

q

/

w

to select “Sign in to your account”, and then press

ENTER

.

If you have the existing Last.fm account, you can sign in to your account to select “

Sign in to your account

”. Enter your user name and password in the next keyboard screen.

Using the keyboard screen

1. Use q / w / e / r and the

ENTER

to enter your user name and password.

2. Select “

OK

”.

3. Press

ENTER

. The “

Confirm your entries

” screen appears.

4. Press

ENTER

.

Please wait...

” appears and then “

Last.fm Internet

Radio

” screen appears.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

2

Use

q

/

w

to select menu and then press ENTER .

Search Station:

You can search station by Artist, Tag, or User Name.

Top Artists Station:

You can play tracks of top-rated artists.

Top Tags Station:

You can play tracks of top-rated tags.

Personal Station:

You can play tracks from personalized station

(“

Your Library

”, “

Your Neighbourhood

” and

Your Recommendations

”).

Using Internet Radio

Profile:

You can play tracks from “

Recently Listened

Tracks

”, “

Library

” and “

Neighbours

”.

Account Info:

Confirm your account information.

Sign Out:

It signs out from your account.

3

Use

q

/

w

to select a station, and press ENTER or

to start playback.

Playback starts and the playback screen appears.

Menu Items

I Love this track:

Track information is saved in Last.fm server, and playback frequency increases.

Ban this track:

Track information is saved in Last.fm server, and playback frequency reduces.

Add to My Favorites:

Adds a station to My Favorites list.

Using scrobbling control

Use q / w to select “

Enable

”, and then press

ENTER

.

*

Internet radio services provided by a third party may be terminated with or without notice.

Internet radio services may not be available in some areas.

En-5

Using Slacker Personal Radio

1

If you do not have an account, create one on the

Slacker website (www.slacker.com) with your computer.

If you already have a Slacker account, select “Sign in to your account” and then press

ENTER

.

The keyboard screen appears. You can enter information from the remote control or the keys on the main unit.

2

If there are no mistakes in the information you have entered, use

q

/

w

/

e

/

r

to select “OK” then press

ENTER

.

An account information confirmation screen appears.

3

If you do not have an account, select “Access without Sign In” and press ENTER to use a restricted version of the service.

Note that use will be restricted.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

4

Use

q

/

w

to select a menu item and then press

ENTER .

To sign out, use q

/ w

to select “

Sign out

” from this screen and then press

ENTER

.

5

Use

q

/

w

to select a station and then press ENTER or

1

to start playback from the station.

The playback screen appears.

6

You can control the tracks with the buttons on the remote control.

Enabled buttons:

1

,

3

,

2

,

6

Menu Items

Rate Song as Favorite:

Stores information to server, making it more likely that the song will be played again.

Ban Song:

Stores information to server, making it less likely that the song will be played again.

Ban Artist:

Stores information to server, making it less likely that the songs from this artist will be played again.

Mark Favorite:

Adds the currently playing station to your favorites.

Unmark Favorite:

Deletes the currently playing station from your favorites.

Add song to Library:

Adds the currently playing track to your library.

Delete song from Library:

Deletes the currently playing track from your library.

Add to My Favorites:

Adds a station or song to My Favorites list.

En-6

Using Internet Radio

Using MP3tunes

Listen to your music collection on your home stereo in complete digital fidelity without a personal computer plus safely backup all your songs. Here’s how:

Creating an Account on your Computer

1

From your computer, open a web browser and go to: www.mp3tunes.com/signup

2

Create an account.

3

Click the Upload link (www.mp3tunes.com/upload) to add files to your Locker.

4

View, edit and listen to your files by clicking on

Player (www.mp3tunes.com/player).

Playing Contents on the AV Receiver

Tip

• Before proceeding, you need to select the MP3tunes service as described in “Common Procedures in Internet Radio Menu”

(

page 1

).

1

Use

q

/

w

to select “Sign in to your account”, and then press ENTER .

2

Enter the e-mail address and password you used when creating your account, select “OK” and press

ENTER .

The keyboard screen appears. You can enter your user name and password from the remote controller or the buttons on the AV receiver.

3

If there are no mistakes in the information you have entered, select “OK” and press ENTER .

An account information confirmation screen appears.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

4

Use

q

/

w

to select the menu, then press ENTER .

Music:

The place to find your Artists, Albums, and Playlists.

Shuffle:

Starts playing a random selection of tracks from your

Locker.

Search:

Find a specific Album, Artist, or Song.

Account Info:

Your MP3tunes account information.

Sign Out:

Log out of your MP3tunes account.

The track at the top of the music list is automatically played back.

Using Internet Radio

5

Use

q

/

w

to select a track and press ENTER or

1

to start playback.

A playback screen appears.

You can control the tracks with the buttons on the remote control.

Enabled buttons: 1 , 3 , 2 , 7 , 6

Menu Items

Go to Menu:

Displays additional menu options.

6

You can view or change your MP3tunes account settings by going to www.mp3tunes.com/account.

En-7

Utilisation d’une webradio

Procédures courantes dans le menu de webradio

Remarque

• Les services disponibles peuvent varier en fonction de la région.

1

Appuyez sur NET .

Une liste des services réseau s’affiche, et le témoin

NET

s’allume. S’il clignote, vérifiez que le câble

Ethernet est fermement branché sur l’ampli-tuner AV.

2

Sélectionnez le service désiré et appuyez sur

ENTER .

La page principale du service sélectionné s’affiche.

Utilisation de plusieurs comptes

L’ampli-tuner AV prend en charge plusieurs comptes utilisateur, ce qui signifie que vous pouvez librement commuter entre plusieurs connexions. Après avoir enregistré des comptes utilisateur, l’identification est réalisée à partir de l’écran «

Users

».

1

Appuyez sur

MENU

lorsque l’écran Users est affiché.

Les éléments de menu suivants s’affichent :

Add new user

:

Remove this user

:

Vous pouvez soit stocker un nouveau compte utilisateur, soit en supprimer un existant.

Conseil

• Certains des services ne permettent pas l’utilisation de plusieurs comptes utilisateur.

• Vous pouvez stocker jusqu’à 10 comptes utilisateur.

• Pour commuter entre les comptes, vous devez d’abord vous déconnecter du compte actuel, puis vous reconnectez depuis l’écran «

Users

».

Utilisation d’une webradio

Pandora ® internet Radio –Pour commencer

(États-Unis uniquement).......................... 2

Utilisation de Rhapsody (Etats-Unis uniquement).............................................. 3

Utilisation de SiriusXM Internet Radio

(Amérique du Nord uniquement) ............ 4

Utilisation de la webradio Last.fm................ 5

Utilisation de Slacker Personal Radio ......... 6

Fr-1

Pandora

®

internet Radio

–Pour commencer (États-Unis uniquement)

Pandora est un service de radio en ligne libre et personnalisé vous permettant de lire la musique que vous connaissez et de découvrir celle que vous aimez.

1

Utilisez

q

/

w

pour sélectionner « I have a Pandora

Account » ou « I’m new to Pandora », puis appuyez sur ENTER .

Si vous ne connaissez pas Pandora sélectionnez «

I’m new to Pandora

». Un code d’activation apparaîtra sur l’écran de votre téléviseur. Notez ce code. Utilisez un ordinateur branché sur Internet et connectez le navigateur à

www.pandora.com/onkyo

Saisissez votre code d’activation puis suivez les instructions pour créer votre compte Pandora et vos stations webradio Pandora personnalisées. Lorsque vous y êtes invités, vous pouvez créer vos stations en saisissant vos chansons et vos artistes préférés. Après la création de votre compte et de vos stations, vous pouvez retourner à votre récepteur Onkyo et appuyez sur entrée pour écouter votre webradio Pandora personnalisée.

Si vous disposez d’un compte Pandora, vous pouvez ajouter votre compte Pandora à votre récepteur Onkyo en sélectionnant «

I have a Pandora Account

» et y accéder en entrant votre adresse e-mail et votre mot de passe.

Conseil

• Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez « Utilisation de plusieurs comptes » (

page 1

).

L’identification peut être réalisée à partir de l’écran

«

Users

».

2

Pour lire une station, utilisez

q

/

w

pour sélectionner la station dans votre liste de stations, puis appuyez sur ENTER .

La lecture débute et l’écran de lecture s’affiche.

Create a New Station :

Saisissez le nom d’une chanson, d’un artiste ou d’un genre et Pandora créera une station radio unique pour vous en fonction des qualités musicales de la chanson, de l’artiste ou du genre choisi.

Eléments du menu

I like this song :

Acceptez la chanson et Pandora lira d’autres musiques similaires.

I don’t like this song :

Rejetez la chanson et Pandora éliminera cette chanson de la station courante.

Why is this song playing? :

Découvrez certains des attributs musicaux que

Pandora utilise pour créer vos stations radio personnelles.

Don’t play the song for a month :

Si vous en avez assez d’une chanson, vous pouvez mettre la chanson « au repos » et Pandora ne la lira plus pendant un mois.

Create station from this artist :

Permet de créer une station radio à partir de cet artiste.

Utilisation d’une webradio

Delete this station :

Ceci supprimera de façon permanente la station de votre compte Pandora. Au cas où vous décideriez de récréer la station avec les mêmes chansons ou les mêmes artistes, tous vos acceptations/rejets précédents seront perdus.

Create station from this song :

Permet de créer une station radio à partir de cette chanson.

Rename this station :

Vous permet de renommer la station radio actuelle.

Bookmark this artist :

Pandora marquera votre artiste préféré pour votre profil sur

www.pandora.com

.

Bookmark this song :

Pandora marquera la chanson en cours et vous permettra de toutes les acheter sur Amazon ou iTunes en une étape !

Add to My Favorites :

Permet d’ajouter une station à la liste My Favorites.

PANDORA, le logo PANDORA, et l’habillage commercial Pandora sont des marques commerciales ou des marques déposées de la société Pandora Media, Inc.

Utilisées avec autorisation.

Fr-2

Utilisation de Rhapsody (Etats-Unis uniquement)

1

Utilisez

q

/

w

pour sélectionner « Sign in to your account », puis appuyez sur ENTER .

Vous devez posséder un compte pour utiliser

Rhapsody. Si vous ne disposez pas encore d’un compte, vous pouvez en créer un à partir de

www.rhapsody.com/onkyo

Si vous possédez déjà un compte Rhapsody, sélectionnez «

Sign in to your account

», puis appuyez sur

ENTER

.

Saisissez votre nom utilisateur (en général votre adresse électronique) et votre mot de passe dans l’écran clavier suivant ou dans Configuration Web.

Utilisation de l’écran clavier

1. Utilisez q

/ w

/ e

/ r

et

ENTER

pour saisir votre nom d’utilisateur et votre mot de passe.

2. Sélectionnez «

OK

».

3. Appuyez sur

ENTER

. L’écran «

Confirm your entries

» s’affiche.

4. Appuyez sur

ENTER

.

Conseil

• Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez « Utilisation de plusieurs comptes » (

page 1

).

L’identification peut être réalisée à partir de l’écran

«

Users

».

2

Utilisez

q

/

w

pour sélectionner le menu, puis appuyez sur ENTER .

Search :

Vous pouvez rechercher des morceaux par artiste, par album ou par piste.

Music Guide :

Vous pouvez lire des pistes à partir des genres,des meilleurs artistes, des meilleurs albums, des meilleures pistes, des nouveautés et des sélections du personnel.

Rhapsody Channels :

Écoutez les canaux de radio programmée par les meilleurs éditeurs de Rhapsody.

Playlists :

Permet de jouer vos listes de lecture personnelles.

My Library :

Marquez vos albums et vos pistes personnelles dans le catalogue de Rhapsody à l’aide de My Library.

Account Info :

Vérifiez les informations de votre compte.

Sign Out :

Déconnectez-vous de votre compte Rhapsody.

Utilisation d’une webradio

3

Utilisez

q

/

w

pour sélectionner un canal, puis appuyez sur

ENTER

ou

1

pour démarrer la lecture.

La lecture débute et l’écran de lecture s’affiche.

Vous pouvez contrôlez les pistes avec les touches sur la télécommande.

Boutons activés :

1

,

3

,

2

,

5

,

4

,

7

,

6

,

RANDOM

,

REPEAT

Remarque

• Sur les canaux Rhapsody, certaines touches ne fonctionnent pas.

Eléments du menu

Add track to My Library :

Marquez les pistes en cours de lecture.

Add album to My Library :

Marquez les albums en cours de lecture.

Add playlist to My Library :

Marquez les listes de lecture en cours de lecture.

Add channel to My Channels :

Marquez les canaux de radio Rhapsody en cours de lecture.

Add to My Favorites :

Permet d’ajouter une piste, un canal ou une liste de lecture à la liste My Favorites.

Conseil

• Vous pouvez supprimer des pistes, des albums et des canaux

Rhapsody marqués de My Library.

Fr-3

Utilisation de SiriusXM Internet Radio

(Amérique du Nord uniquement)

Votre ampli-tuner AV Onkyo comprend un essai gratuit de

SiriusXM Internet Radio. L’écran « Account Info » affiche le nombre de jours restants dans votre essai. Une fois la période d’essai expirée, si vous souhaitez continuer à

écouter le service, vous devez vous abonner. Pour vous inscrire, accédez à l’adresse

www.siriusxm.com/internetradio

à l’aide de votre ordinateur.

Lorsque vous vous inscrivez, vous devez fournir un nom est un mot de passe utilisateur qui doivent être saisis dans l’ampli-tuner AV.

Pour utiliser SiriusXM Internet Radio, l’ampli-tuner AV doit être connecté à Internet. Suivez les étapes ci-dessous à l’aide de la télécommande :

Utilisation d’une webradio

1

Utilisez

q

/

w

pour sélectionner « Sign In », puis appuyez sur ENTER .

Si vous possédez déjà un compte SIRIUS, vous pouvez y accéder en sélectionnant «

Sign In

».

Saisissez votre nom utilisateur et votre mot de passe dans l’écran clavier suivant ou dans Configuration

Web. Si vous ne connaissez pas votre nom d’utilisateur ou votre mot de passe, appelez Sirius XM au (888) 539-7474 pour obtenir une assistance.

Conseil

• Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez « Utilisation de plusieurs comptes » (

page 1

).

L’identification peut être réalisée à partir de l’écran

«

Users

».

Utilisation de l’écran clavier

1. Utilisez q

/ w

/ e

/ r

et

ENTER

pour saisir votre nom d’utilisateur et votre mot de passe.

2. Sélectionnez «

OK

».

3. Appuyez sur

ENTER

. L’écran «

Confirm your entries

» s’affiche.

4. Appuyez sur

ENTER

.

«

Please wait...

» s’affiche, puis l’écran «

SiriusXM

Internet Radio

» affiche la catégorie que vous pouvez sélectionner.

2

Utilisez

q

/

w

pour sélectionner la catégorie, puis appuyez sur ENTER .

L’écran de la liste des canaux de la catégorie sélectionnée s’affiche.

3

Utilisez

q

/

w

pour sélectionner le canal de votre choix, puis appuyez sur

ENTER

.

L’écran de lecture du canal sélectionné s’affiche et vous pouvez écouter SiriusXM Internet Radio.

Vous pouvez contrôlez les pistes avec les touches sur la télécommande.

Boutons activés :

2

,

3

,

7

,

6

Eléments du menu

Add to My Favorites :

Permet d’ajouter un canal à la liste My Favorites.

Les abonnements SiriusXM Internet Radio sont vendus séparément et sont subordonnés par les conditions Sirius

(voir www.sirius.com). Assurez-vous de lire cet accord avant d’acquérir votre abonnement. Sirius, XM et tous les logos et marques afférents sont des marques déposées de

Sirius XM Radio Inc. et de ses filiales. Tous droits réservés.

Fr-4

Utilisation de la webradio Last.fm

Last.fm un service de musique qui apprend ce que vous aimez…

Votre nouvel ampli-tuner AV Onkyo est très intelligent. Si vous avez un compte Last.fm gratuit, il garde une trace de toutes les chansons que vous avez juste jouées. Quand vous vous rendez sur le site Web de Last.fm, vous pouvez voir les graphiques personnels de la musique que vous avez appréciée, les partagez avec vos amis et également voir ce qu’ils aiment.

Avec des milliers de biographies, de revues et un choix infini de stations de radio personnalisées et sans pub,

Last.fm est excellent moyen de découvrir de la musique.

Créez aujourd’hui votre compte Last.fm gratuit sur www.last.fm/join

Inscrivez-vous et vous pourrez apprécier le meilleur de la radio sans pub Last.fm sur votre ampli-tuner AV Onkyo sans ordinateur !

Recommended Radio :

Découvrez les recommandations personnalisées futées qui changent en même temps que vos goûts.

Artist Radio :

Sélectionnez n’importe quel artiste et nous vous jouerons une station entière de musique inspirée par votre choix.

My Library :

Reposez-vous de retour et appréciez les sélections à partir de toute la musique que vous avez entendue depuis que vous avez joint Last.fm.

Tag Radio :

Funk polonaise ? Death pop ? Pensez à un style et nous vous divertirons avec pendant des heures.

Commencez votre essai gratuit immédiatement à la création votre compte et découvrez par vous-même ce que cela fait d’avoir la musique du monde au bouts des doigts.

Les derniers prix et les informations complètes sont disponibles sur www.last.fm/subscribe

1

Utilisez

q

/

w

pour sélectionner « Sign in to your account », puis appuyez sur ENTER .

Vous possédez déjà un compte Last.fm, vous pouvez vous y connecter pour sélectionner «

Sign in to your account

». Saisissez votre nom utilisateur et votre mot de passe dans l’écran clavier suivant.

Utilisation de l’écran clavier

1. Utilisez q

/ w

/ e

/ r

et le bouton

ENTER

pour saisir votre nom d’utilisateur et votre mot de passe.

2. Sélectionnez «

OK

».

3. Appuyez sur

ENTER

. L’écran «

Confirm your entries

» s’affiche.

4. Appuyez sur

ENTER

.

«

Please wait...

» apparait puis l’écran «

Last.fm

Internet Radio

» apparait.

Conseil

• Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez « Utilisation de plusieurs comptes » (

page 1

).

L’identification peut être réalisée à partir de l’écran

«

Users

».

2

Utilisez

q

/

w

pour sélectionner un menu puis appuyez sur ENTER .

Search Station :

Vous pouvez rechercher une station par artiste, par tag ou par nom d’utilisateur.

Top Artists Station :

Vous pouvez lire des pistes des artistes les mieux évalués.

Top Tags Station :

Vous pouvez lire des pistes des tags les mieux évalués.

Personal Station :

Vous pouvez lire des pistes de votre station personnalisée («

Your Library

», «

Your

Neighbourhood

» et «

Your Recommendations

»).

Utilisation d’une webradio

Profile :

Vous pouvez lire des pistes de «

Recently Listened

Tracks

», «

Library

» et «

Neighbours

».

Account Info :

Vérifiez les informations de votre compte.

Sign Out :

Pour vous déconnecter de votre compte.

3

Utilisez

q

/

w

pour sélectionner une station, puis appuyez sur ENTER ou

pour démarrer la lecture.

La lecture débute et l’écran de lecture s’affiche.

Eléments du menu

I Love this track :

L’information de la piste est sauvegardée dans le serveur Last.fm, et la fréquence de lecture augmente.

Ban this track :

L’information de la piste est sauvegardée dans le serveur Last.fm, et la fréquence de lecture diminue.

Add to My Favorites :

Permet d’ajouter une station à la liste My Favorites.

Utilisation du contrôle Scrobbling

Utilisez q

/ w

pour sélectionner «

Enable

», puis appuyez sur

ENTER

.

*

Les services de webradio fournis par un tiers peuvent être résiliés avec ou sans préavis.

Les services de webradio peuvent ne pas être accessibles dans certaines zones.

Fr-5

Utilisation de Slacker Personal Radio

1

Si vous ne possédez pas de compte, créez-en un à partir du site Web de Slacker (www.slacker.com) à l’aide de votre ordinateur.

Si vous possédez déjà un compte Slacker, sélectionnez « Sign in to your account », puis appuyez sur ENTER .

L’écran clavier s’affiche. Pouvez saisir des informations à partir de la télécommande ou des touches sur l’appareil principal.

2

Si les informations que vous avez saisies ne comportent pas d’erreur, utilisez

q

/

w

/

e

/

r

pour sélectionner « OK », puis appuyez sur ENTER .

L’écran de confirmation des informations du compte s’affiche.

3

Si vous ne possédez pas de compte, sélectionnez

« Access without Sign In », puis appuyez sur

ENTER pour utiliser une version restreinte du service.

Veuillez noter que l’utilisation est restreinte.

Conseil

• Si vous souhaitez utiliser plusieurs comptes utilisateur, consultez « Utilisation de plusieurs comptes » (

page 1

).

L’identification peut être réalisée à partir de l’écran

«

Users

».

4

Utilisez

q

/

w

pour sélectionner un élément du menu, puis appuyez sur ENTER .

Pour vous déconnecter, utilisez q / w pour sélectionner

«

Sign out

» depuis cet écran, puis appuyez sur

ENTER

.

5

Utilisez

q

/

w

pour sélectionner une station, puis appuyez sur ENTER ou

1

pour démarrer la lecture depuis cette station.

L’écran de lecture apparaît.

6

Vous pouvez contrôlez les pistes avec les touches sur la télécommande.

Boutons activés :

1

,

3

,

2

,

6

Eléments du menu

Rate Song as Favorite :

Permet de stocker des informations sur le serveur, et d’augmenter la probabilité que le morceau soit lu de nouveau.

Ban Song :

Permet de stocker des informations sur le serveur, et de diminuer la probabilité que le morceau soit lu de nouveau.

Ban Artist :

Permet de stocker des informations sur le serveur, et de diminuer la probabilité que les morceaux de cet artiste soient lus de nouveau.

Mark Favorite :

Permet d’ajouter la station en cours de lecture à vos favoris.

Unmark Favorite :

Permet de supprimer la station en cours de lecture de vos favoris.

Add song to Library :

Permet d’ajouter la piste en cours de lecture à votre bibliothèque.

Delete song from Library :

Permet de supprimer la piste en cours de lecture de votre bibliothèque.

Add to My Favorites :

Permet d’ajouter une station ou un morceau à la liste

My Favorites.

Fr-6

Utilisation d’une webradio

Uso de Internet Radio

Procedimientos comunes en el menú

Internet Radio

Nota

• Los servicios disponibles pueden variar de una región a otra.

1

Pulse NET .

Aparecerá una lista de los servicios de red y se iluminará el indicador

NET

. Si parpadea, verifique que el cable Ethernet esté firmemente conectado al receptor de AV.

2

Seleccione el servicio deseado y pulse ENTER .

Aparecerá la página principal del servicio seleccionado.

Uso de múltiples cuentas

El receptor de AV permite múltiples cuentas de usuario, lo que quiere decir que se puede cambiar libremente entre varios usuarios. Después de registrar las cuentas de usuario, el acceso se realiza desde la pantalla “

Users

”.

1

Pulse MENU cuando aparezca la pantalla de usuarios.

Aparecerán los siguientes elementos del menú:

Add new user

:

Remove this user

:

Puede guardar una nueva cuenta de usuario o borrar una existente.

Consejo

• Algunos de los servicios no permiten el uso de múltiples cuentas de usuario.

• Puede guardar hasta 10 cuentas de usuario.

• Para cambiar entre cuentas debe antes cerrar sesión en la cuenta actual y acceder de nuevo en la pantalla “

Users

”.

Uso de Internet Radio

Pandora ® Internet Radio –Primeros pasos

(solo EE.UU.) ............................................ 2

Uso de Rhapsody (sólo EE.UU.)................... 3

Uso de SiriusXM Internet Radio (solo

Norteamérica) ........................................... 4

Uso de Last.fm Internet Radio ...................... 5

Uso de Slacker Personal Radio .................... 6

Es-1

Pandora

®

Internet Radio

–Primeros pasos (solo EE.UU.)

Pandora es un servicio de radio por Internet gratuito y personalizado que reproduce la música que usted conoce y le ayudará a descubrir música que le encantará.

1

Utilice

q

/

w

para seleccionar “I have a Pandora

Account” o “I’m new to Pandora” y luego pulse

ENTER .

Si no conoce Pandora seleccione “

I’m new to

Pandora

”. Verá un código de activación en la pantalla del televisor. Tome nota de este código. Vaya a un ordenador conectado a Internet y dirija el navegador a

www.pandora.com/onkyo

Introduzca su código de activación y siga las instrucciones para crear su cuenta de Pandora y sus emisoras de radio por Internet personalizadas de

Pandora. Puede crear sus propias emisoras introduciendo sus canciones y artistas favoritos cuando aparezca la solicitud correspondiente. Una vez creada su cuenta y sus emisoras, puede regresar al receptor Onkyo y pulsar Enter para empezar a escuchar su radio por Internet personalizada de

Pandora.

Si ya dispone de una cuenta de Pandora, puede añadirla al receptor Onkyo seleccionando “

I have a

Pandora Account

” e iniciando la sesión con su dirección de correo electrónico y contraseña.

Consejo

• Si desea utilizar múltiples cuentas de usuario, consulte “Uso de múltiples cuentas” (

página 1

). Se puede iniciar sesión desde la pantalla “

Users

”.

2

Utilice

q

/

w

para seleccionar la emisora en la lista de emisoras y luego pulse ENTER .

Se inicia la reproducción y aparece la pantalla de reproducción.

Create a New Station:

Introduzca el nombre de una canción, artista o género;

Pandora creará una emisora de radio exclusiva para usted basada en las cualidades musicales de esa canción, de ese artista o de ese género.

Elementos del menú

I like this song:

Si aprueba (pulgar arriba) una canción, Pandora reproducirá más música parecida.

I don’t like this song:

Si no aprueba (pulgar abajo) la canción, Pandora eliminará dicha canción de la emisora actual.

Why is this song playing?:

Descubra algunos de los atributos musicales que

Pandora utiliza para crear sus emisoras de radio personalizadas.

Don’t play the song for a month:

Si se cansa de una canción, puede “silenciarla” de modo que Pandora no la reproduzca durante un mes.

Create station from this artist:

Crea una emisora de radio a partir de este artista.

Uso de Internet Radio

Delete this station:

Esto eliminará de forma permanente una emisora de su cuenta de Pandora. Toda la información sobre sus aprobaciones / desaprobaciones se perderá si quiere volver a crear la emisora con la misma canción o artista.

Create station from this song:

Crea una emisora de radio a partir de esta canción.

Rename this station:

Le permite renombrar la emisora de radio actual.

Bookmark this artist:

Pandora marcará su artista favorito para su perfil en

www.pandora.com

.

Bookmark this song:

Pandora marcará la canción actual y le permitirá comprarlas todas en Amazon o iTunes con un solo paso.

Add to My Favorites:

Añade una emisora a la lista Mis favoritos.

PANDORA, el logotipo de PANDORA logo, y la imagen corporativa de Pandora son marcas comerciales o marcas comerciales registradas de Pandora Media, Inc. Uso con permiso.

Es-2

Uso de Rhapsody (sólo EE.UU.)

1

Utilice

q

/

w

para seleccionar “Sign in to your account” y luego pulse ENTER .

Para utilizar Rhapsody, necesitará una cuenta. Si todavía no tiene una, puede crear una nueva en

www.rhapsody.com/onkyo

Si ya tiene una cuenta Rhapsody, seleccione “

Sign in to your account

” y pulse

ENTER

.

Escriba su nombre de usuario (normalmente el correo electrónico) y contraseña en la pantalla de teclado que aparece a continuación o en la configuración web.

Utilización de la pantalla de teclado

1. Utilice q

/ w

/ e

/ r

y

ENTER

para introducir su nombre de usuario y su contraseña.

2. Seleccione “

OK

”.

3. Pulse

ENTER

. Aparecerá la pantalla “

Confirm your entries

”.

4. Pulse

ENTER

.

Consejo

• Si desea utilizar múltiples cuentas de usuario, consulte “Uso de múltiples cuentas” (

página 1

). Se puede iniciar sesión desde la pantalla “

Users

”.

2

Utilice

q

/

w

para seleccionar el menú y luego pulse

ENTER .

Search:

Puede buscar música por artista, álbum o canción.

Music Guide:

Puede reproducir canciones por géneros, artistas principales, álbumes principales o canciones principales, novedades, selección del sitio.

Rhapsody Channels:

Escuche las emisoras de radio programadas por los principales redactores de Rhapsody.

Playlists:

Reproduzca sus listas personales.

My Library:

Marque sus álbumes y canciones preferidas en el catálogo de Rhapsody, usando Mi biblioteca.

Account Info:

Confirme los datos de su cuenta.

Sign Out:

Salga de su cuenta Rhapsody.

Uso de Internet Radio

3

Utilice

q

/

w

para seleccionar una emisora y luego pulse

ENTER

o

1

para iniciar la reproducción.

Se inicia la reproducción y aparece la pantalla de reproducción.

Puede controlar las pistas con los botones del mando a distancia.

Botones activados:

1

,

3

,

2

,

5

,

4

,

7

,

6

,

RANDOM

,

REPEAT

Nota

• En Rhapsody Channels, algunos de los botones no funcionan.

Elementos del menú

Add track to My Library:

Marca las canciones que se están reproduciendo actualmente.

Add album to My Library:

Marca los álbumes que se están reproduciendo actualmente.

Add playlist to My Library:

Marca las listas de reproducción que se están reproduciendo actualmente.

Add channel to My Channels:

Marca las emisoras de Rhapsody que se están reproduciendo actualmente.

Add to My Favorites:

Añade una canción, emisora o lista de reproducción a la lista Mis favoritos.

Consejo

• Puede eliminar las canciones, los álbumes y las emisoras de

Rhapsody marcados de Mi biblioteca.

Es-3

Uso de SiriusXM Internet Radio (solo

Norteamérica)

Su receptor de AV Onkyo incluye una prueba gratuita de

SiriusXM Internet Radio. La pantalla “Account Info” muestra los días que quedan de la prueba. Una vez que termine el periodo de prueba, si desea seguir escuchando este servicio, deberá contratarlo. para suscribirse vaya a

www.siriusxm.com/internetradio

con su ordenador.

Cuando se suscriba, recibirá un nombre de usuario y una contraseña que deberá introducir en el receptor de AV.

Para poder utilizar SiriusXM Internet Radio, el receptor de

AV debe estar conectado a internet. Para usar el mando a distancia, siga este procedimiento:

Uso de Internet Radio

1

Utilice

q

/

w

para seleccionar “Sign In”, y luego pulse ENTER .

Si ya tiene una cuenta SIRIUS, puede acceder seleccionando “

Sign In

”. Escriba su nombre de usuario y contraseña en la pantalla de teclado que aparece a continuación o en la configuración web. Si no sabe su nombre de usuario o la contraseña, llame a

Sirius XM al número (888) 539-7474 para solicitar asistencia.

Consejo

• Si desea utilizar múltiples cuentas de usuario, consulte “Uso de múltiples cuentas” (

página 1

). Se puede iniciar sesión desde la pantalla “

Users

”.

Utilización de la pantalla de teclado

1. Utilice q / w / e / r y

ENTER

para introducir su nombre de usuario y su contraseña.

2. Seleccione “

OK

”.

3. Pulse

ENTER

. Aparecerá la pantalla “

Confirm your entries

”.

4. Pulse

ENTER

.

Aparecerá “

Please wait...

” y después la pantalla

SiriusXM Internet Radio

”, que muestra la categoría disponible para la selección.

2

Utilice

q

/

w

para seleccionar la categoría y luego pulse

ENTER

.

Aparece una pantalla con una lista de emisoras de la categoría seleccionada.

3

Utilice

q

/

w

para seleccionar la emisora deseada y luego pulse ENTER .

Aparecerá la pantalla de reproducción de la emisora seleccionada y ahora usted podrá escuchar SiriusXM

Internet Radio.

Puede controlar las pistas con los botones del mando a distancia.

Botones activados:

2

,

3

,

7

,

6

Elementos del menú

Add to My Favorites:

Añade una emisora a la lista Mis favoritos.

Las suscripciones a SiriusXM Internet Radio se venden por separado y se rigen por las condiciones de Sirius (consulte www.sirius.com). Lea atentamente este acuerdo antes de comprar la suscripción. Sirius, XM y todas las marcas y logotipos relacionados son marcas comerciales de Sirius

XM Radio Inc. y sus filiales. Todos los derechos reservados.

Es-4

Uso de Last.fm Internet Radio

Last.fm es un servicio musical que sabe lo que le gusta...

Su nuevo receptor de AV Onkyo es muy inteligente. Si tiene una cuenta gratuita de Last.fm, hará un seguimiento de todas las canciones que acaba de escuchar. Cuando visite el sitio web de Last.fm, podrá ver listas personales de la música que ha disfrutado, compartirlas con sus amigos y también ver lo que les gusta a ellos.

Con sus miles de biografías, críticas y una infinita variedad de emisoras de radio personalizadas y sin publicidad,

Last.fm es una forma excelente de descubrir música. Cree hoy mismo una cuenta gratuita de Last.fm en www.last.fm/join

Si se suscribe podrá disfrutar de lo mejor de Last.fm Radio sin anuncios en su receptor de AV Onkyo sin necesidad de un ordenador.

Recommended Radio:

Descubra nuestras interesantes recomendaciones personalizadas que se adaptan a sus gustos en cada momento.

Artist Radio:

Escoja cualquier artista y podrá escuchar una emisora de radio inspirada exclusivamente en su elección.

My Library:

Relájese y disfrute de selecciones de toda la música que ha escuchado desde que se registró en Last.fm.

Tag Radio:

¿Polish funk? ¿Death pop? Piense en un estilo y podrá escucharlo durante horas.

Pruébelo gratis ahora mismo. Cree una cuenta y verá por sí mismo lo que significa tener toda la música del mundo al alcance de sus oídos. Puede consultar los precios actualizados y toda la información que desee en www.last.fm/subscribe

1

Utilice

q

/

w

para seleccionar “Sign in to your account”, y luego pulse ENTER .

Si ya tiene una cuenta de Last.fm, puede acceder a ella para seleccionar “

Sign in to your account

”.

Introduzca su nombre de usuario y contraseña en la siguiente pantalla de teclado.

Utilización de la pantalla de teclado

1. Utilice q

/ w

/ e

/ r

y

ENTER

para introducir su nombre de usuario y su contraseña.

2. Seleccione “

OK

”.

3. Pulse

ENTER

. Aparecerá la pantalla “

Confirm your entries

”.

4. Pulse

ENTER

.

Aparecerá “

Please wait...

” y después la pantalla

Last.fm Internet Radio

”.

Consejo

• Si desea utilizar múltiples cuentas de usuario, consulte “Uso de múltiples cuentas” (

página 1

). Se puede iniciar sesión desde la pantalla “

Users

”.

2

Utilice

q

/

w

para seleccionar un menú y luego pulse

ENTER

.

Search Station:

Puede buscar emisoras por artista, etiquetas o nombre de usuario.

Top Artists Station:

Puede reproducir canciones de los artistas mejor clasificados.

Top Tags Station:

Puede reproducir canciones con las etiquetas mejor clasificadas.

Personal Station:

Puede reproducir pistas de una emisora personalizada

(“

Your Library

”, “

Your Neighbourhood

” y “

Your

Recommendations

”).

Uso de Internet Radio

Profile:

Puede reproducir pistas de “

Recently Listened

Tracks

”, “

Library

” y “

Neighbours

”.

Account Info:

Confirme los datos de su cuenta.

Sign Out:

Se desconecta de su cuenta.

3

Utilice

q

/

w

para seleccionar una emisora y luego pulse ENTER o

para iniciar la reproducción.

Se inicia la reproducción y aparece la pantalla de reproducción.

Elementos del menú

I Love this track:

Se guarda la información sobre la canción en el servidor de Last.fm y aumenta la frecuencia con la que se reproduce.

Ban this track:

Se guarda la información sobre la canción en el servidor de Last.fm y se reduce la frecuencia con la que se reproduce.

Add to My Favorites:

Añade una emisora a la lista Mis favoritos.

Uso del control de scrobbling

Utilice q / w para seleccionar “

Enable

”, y luego pulse

ENTER

.

* Los servicios de radio por Internet suministrados por terceros pueden cancelarse con o sin aviso previo.

Es posible que los servicios de radio por Internet no estén disponibles en algunas zonas.

Es-5

Uso de Slacker Personal Radio

1

Si no tiene una cuenta, cree una en el sitio web de

Slacker (www.slacker.com) con su ordenador.

Si ya tiene una cuenta de Slacker, seleccione “Sign in to your account” y pulse ENTER .

Aparecerá la pantalla de teclado. Puede introducir información desde el mando a distancia o desde el teclado de la unidad principal.

2

Si no hay errores en la información que ha introducido, utilice

q

/

w

/

e

/

r

para seleccionar

“OK” y luego pulse ENTER .

Aparecerá una pantalla de confirmación de la información de la cuenta.

3

Si no tiene una cuenta, seleccione “Access without

Sign In” y pulse ENTER para utilizar una versión restringida del servicio.

Tenga en cuenta que el uso estará restringido.

Consejo

• Si desea utilizar múltiples cuentas de usuario, consulte “Uso de múltiples cuentas” (

página 1

). Se puede iniciar sesión desde la pantalla “

Users

”.

4

Utilice

q

/

w

para seleccionar un menú y luego pulse

ENTER

.

Para salir, utilice q

/ w

para seleccionar “

Sign out

” en esta pantalla y luego pulse

ENTER

.

5

Utilice

q

/

w

para seleccionar una emisora y luego pulse ENTER o

1

para iniciar la reproducción de la emisora.

Aparecerá la pantalla de reproducción.

6

Puede controlar las pistas con los botones del mando a distancia.

Botones activados:

1

,

3

,

2

,

6

Elementos del menú

Rate Song as Favorite:

Guarda información en el servidor, haciendo que sea más probable que la canción se vuelva a reproducir.

Ban Song:

Guarda información en el servidor, haciendo que sea menos probable que la canción se vuelva a reproducir.

Ban Artist:

Guarda información en el servidor, haciendo que sea menos probable que las canciones de este artista se vuelvan a reproducir.

Mark Favorite:

Añade la emisora que se está reproduciendo actualmente a los favoritos.

Unmark Favorite:

Elimina la emisora que se está reproduciendo actualmente de los favoritos.

Add song to Library:

Añade la canción que se está reproduciendo actualmente a su biblioteca.

Delete song from Library:

Elimina la canción que se está reproduciendo actualmente de la biblioteca.

Add to My Favorites:

Añade una emisora o canción a la lista Mis favoritos.

Es-6

Uso de Internet Radio

SN 29401189B

(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

Y1203-2

* 2 9 4 0 1 1 8 9 B *

Using Internet Radio

Using Internet Radio

Common Procedures in Internet Radio

Menu

Note

• Available services may vary depending on the region.

1

Press NET .

A list of the network services appears, and the

NET

indicator lights. If it flashes, verify that the Ethernet cable is firmly connected to the AV receiver.

2

Select the desired service and press ENTER .

The top page of the selected service appears.

Using Multiple Accounts

The AV receiver supports multiple user accounts, which means you can freely switch between several logins.

After registering user accounts, login is performed from the “

Users

” screen.

1

Press

MENU

while the Users screen is displayed.

The following menu items appear:

Add new user

:

Remove this user

:

You can either store a new user account, or delete an existing one.

Tip

• Some of the services don’t allow the use of multiple user accounts.

• You can store up to 10 user accounts.

• To switch between accounts you must first log out from the current account, and log in again on the “

Users

” screen.

Using Last.fm Internet Radio ........................ 2

En-1

Using Last.fm Internet Radio

Last.fm is a music service that learns what you love...

Your new Onkyo AV receiver is very clever. If you have a free Last.fm account, it will keep track of all the songs you’ve just played. When you visit the Last.fm website, you can see personal charts of the music you’ve enjoyed, share them with friends and see what they like, too.

With thousands of biographies, reviews and an endless choice of personalised, ad-free radio stations, Last.fm is a great way to discover music. Pick up your free Last.fm account today at www.last.fm/join

UK and Germany only:

Get a subscription and you can enjoy the best of ad-free

Last.fm Radio on your Onkyo AV receiver without a computer!

Recommended Radio:

Discover smart personalised recommendations that adapt as your tastes change.

Artist Radio:

Pick any artist and we’ll play you a whole station of music inspired by your choice.

My Library:

Sit back and enjoy selections from all the music you’ve heard since you joined Last.fm.

Tag Radio:

Polish funk? Death pop? Think of a style and we’ll entertain you with it for hours.

Start your free trial straight away when you create your account and see for yourself what it’s like to have the world’s music at your fingertips. Latest prices and full information are available at www.last.fm/subscribe

1

Use

q

/

w

to select “Sign in to your account”, and then press

ENTER

.

If you have the existing Last.fm account, you can sign in to your account to select “

Sign in to your account

”. Enter your user name and password in the next keyboard screen.

Using the keyboard screen

1. Use q / w / e / r and the

ENTER

to enter your user name and password.

2. Select “

OK

”.

3. Press

ENTER

. The “

Confirm your entries

” screen appears.

4. Press

ENTER

.

Please wait...

” appears and then “

Last.fm Internet

Radio

” screen appears.

Tip

• If you want to use multiple user accounts, see “Using

Multiple Accounts” (

page 1

). Login can be made from the “

Users

” screen.

2

Use

q

/

w

to select menu and then press ENTER .

Search Station:

You can search station by Artist, Tag, or User Name.

Top Artists Station:

You can play tracks of top-rated artists.

Top Tags Station:

You can play tracks of top-rated tags.

Personal Station:

You can play tracks from personalized station (“

Your

Library

”, “

Your Neighbourhood

” and “

Your

Recommendations

”).

Using Internet Radio

Profile:

You can play tracks from “

Recently Listened

Tracks

”, “

Library

” and “

Neighbours

”.

Account Info:

Confirm your account information.

Sign Out:

It signs out from your account.

3

Use

q

/

w

to select a station, and press ENTER or

to start playback.

Playback starts and the playback screen appears.

Enabled buttons:

1

,

2

,

6

Menu Items

I Love this track:

Track information is saved in Last.fm server, and playback frequency increases.

Ban this track:

Track information is saved in Last.fm server, and playback frequency reduces.

Add to My Favorites:

Adds a station to My Favorites list.

Using scrobbling control

Use q

/ w

to select “

Enable

”, and then press

ENTER

.

* Internet radio services provided by a third party may be terminated with or without notice.

Internet radio services may not be available in some areas.

En-2

Internetradio verwenden

Allgemeine Verfahren bei den

Internetradio-Menüs

Anmerkung

• Die verfügbaren Dienste sind länderabhängig verschieden.

1

Drücken Sie NET .

Es erscheint eine Liste der Netzwerkdienste und die

NET

-Anzeige leuchtet. Wenn sie blinkt, überprüfen

Sie ob das Ethernet-Kabel fest im AV-Receiver eingesteckt ist.

2

Wählen Sie den gewünschten Service aus und drücken Sie

ENTER

.

Die oberste Seite des ausgewählten Services erscheint.

Verwendung mehrerer Konten

Der AV-Receiver unterstützt mehrere Nutzerkonten, was bedeutet, dass Sie frei zwischen mehreren Logins umschalten können. Nach der Anmeldung der

Nutzerkonten wird das Login vom „

Users

“ Bildschirm aus vorgenommen.

1

Drücken Sie MENU während der Bildschirm des

Nutzers angezeigt wird.

Das folgende Menü erscheint:

Add new user

:

Remove this user

:

Sie können entweder ein neues Nutzerkonto abspeichern oder ein bestehendes löschen.

Tipp

• Einige dieser Dienstleistungen lassen keine mehrfachen

Nutzerkonten zu.

• Sie können bis zu 10 Nutzerkonten speichern.

• Um zwischen den Konten umzuschalten, müssen Sie sich zuerst aus Ihrem aktuellen Konto ausloggen und sich dann wieder auf dem „

Users

“ Bildschirm einloggen.

Internetradio verwenden

Verwendung von Last.fm Internet Radio ..... 2

De-1

Verwendung von Last.fm Internet Radio

Last.fm ist ein Musikdienst, der sich Ihre

Lieblingsmusik merkt...

Ihr neuer Onkyo AV-Receiver ist äußerst clever. Wenn Sie ein kostenloses Last.fm-Konto eingerichtet haben, werden darin alle kürzlich abgespielten Titel gespeichert. Wenn Sie die Last.fm-

Website besuchen, können Sie Ihre persönlichen Charts der von

Ihnen abgespielten Musik anzeigen; teilen Sie diese mit Freunden und sehen Sie auch, welche Musik Ihre Freunde mögen.

Mit tausenden von Biografien, Rezensionen und einer schier endlosen Auswahl an persönlich angepassten, werbefreien

Radiosendern ist Last.fm eine großartige Gelegenheit, um

Musik zu entdecken. Holen Sie sich Ihr kostenloses Last.fm-

Konto noch heute unter www.last.fm/join

Nur für Großbritannien und Deutschland:

Holen Sie sich ein Abonnement und Sie können auch ohne

Computer die besten werbefreien Last.fm-Radiosender auf

Ihrem Onkyo AV-Receiver hören!

Recommended Radio:

Entdecken Sie smarte, persönlich angepasste Empfehlungen, die sich mit Ihrem Musikgeschmack verändern.

Artist Radio:

Wählen Sie einen beliebigen Interpreten und wir spielen für Sie einen ganzen Radiosender mit durch Ihre Wahl inspirierter Musik.

My Library:

Lehnen Sie sich zurück und erfreuen Sie sich an einer

Auswahl aller Musik, die Sie seit Ihrer Mitgliedschaft bei

Last.fm gehört haben.

Tag Radio:

Polish Funk? Death Pop? Denken Sie an einen Musikstil und wir unterhalten Sie stundenlang damit.

Starten Sie Ihr kostenloses Probeabo direkt wenn Sie Ihr

Konto erstellen und finden Sie selbst heraus wie es ist, jederzeit die Musik der ganzen Welt abrufen zu können.

Die aktuellen Nutzungspreise und umfassende Infos sind unter www.last.fm/subscribe erhältlich

1

Verwenden Sie

q

/

w

, um „Sign in to your account“ auszuwählen und dann drücken Sie ENTER .

Wenn Sie über einen bestehenden Last.fm Konto verfügen, können Sie sich anmelden und „

Sign in to your account

“ wählen. Geben Sie Ihre Ihre

Benutzernamen und das Kennwort in der folgenden

Tastaturanzeige ein.

Verwendung der Tastaturanzeige

1. Verwenden Sie q / w / e / r und den

ENTER

, um

Ihren Nutzernamen und Passwort einzugeben.

2. Wählen Sie „

OK

“.

3. Drücken Sie

ENTER

. Die Anzeige „

Confirm your entries

“ erscheint.

4. Drücken Sie

ENTER

.

Please wait...

“ wird angezeigt und danach erscheint die „

Last.fm Internet Radio

“-Anzeige.

Tipp

• Falls Sie mehrere Nutzerkonten verwenden möchten, schlagen Sie bitte unter „Verwendung mehrerer Konten“ nach (

Seite 1

). Das Login kann vom „

Users

“-

Bildschirm aus erfolgen.

2

Verwenden Sie

q

/

w

, um das Menü auszuwählen und dann drücken Sie

ENTER

.

Search Station:

Sie können einen Sender anhand Interpreten, Tags oder Benutzernamen suchen.

Top Artists Station:

Sie können Titel der am besten bewerteten Interpreten wiedergeben.

Top Tags Station:

Sie können Titel der am besten bewerteten Tags wiedergeben.

Personal Station:

Sie können Titel aus einem persönlich angepassten

Sender wiedergeben („

Your Library

“, „

Your

Neighbourhood

“ und „

Your Recommendations

“).

Internetradio verwenden

Profile:

Sie können Titel aus „

Recently Listened Tracks

“,

Library

“ und „

Neighbours

“ wiedergeben.

Account Info:

Bestätigen Sie Ihre Kontoinformation.

Sign Out:

Zur Abmeldung aus Ihrem Konto.

3

Verwenden Sie

q

/

w

, um einen Sender auszuwählen und dann drücken Sie ENTER oder

, um die

Wiedergabe zu starten.

Die Wiedergabe wird gestartet und die

Wiedergabeanzeige erscheint.

Aktivierte Tasten:

1

,

2

,

6

Menüsymbole

I Love this track:

Titel-Informationen werden auf dem Last.fm-Server gespeichert und die Häufigkeit der Wiedergabe wird erhöht.

Ban this track:

Titel-Informationen werden auf dem Last.fm-Server gespeichert und die Häufigkeit der Wiedergabe wird verringert.

Add to My Favorites:

Fügt einen Sender zu meiner My Favorites Liste hinzu.

Scrobbling-Steuerung verwenden

Verwenden Sie q

/ w

, um „

Enable

“ auszuwählen und dann drücken Sie

ENTER

.

*

Von Drittparteien zur Verfügung gestellte Internetradio-Dienste können unter Umständen ohne Vorankündigung eingestellt werden.

In bestimmten Gebieten sind Internetradio-Dienste eventuell nicht verfügbar.

Y1112-1

SN 29401229

(C) Copyright 2012 Onkyo Sound & Vision Corporation Japan. All rights reserved.

* 2 9 4 0 1 2 2 9 *

Remote Control Codes

/

1

Remote Control Codes

1

While holding down the REMOTE MODE button to which you want to assign a code, press and hold down [DISPLAY] (about 3 seconds).

The REMOTE MODE button/Remote indicator lights.

On Integra products, button names are capitalized. For example, “Remote Mode” button and “Display” button.

Notes:

• Remote control codes cannot be entered for [RECEIVER] and the multi zone button.

• Only TV remote control codes can be entered for [TV].

• Except for [RECEIVER], [TV], and the multi zone button, remote control codes from any category can be assigned for the REMOTE MODE buttons. However, these buttons also work as input selector buttons, so choose a REMOTE MODE button that corresponds with the input to which you connect your component. For example, if you connect your CD player to the CD input, choose [TV/CD] when entering its remote control code.

2

Within 30 seconds, use the number buttons to enter the 5-digit remote control code.

The REMOTE MODE button/Remote indicator flashes twice.

If the remote control code is not entered successfully, the REMOTE MODE button/Remote indicator will flash once slowly.

Notes:

• The flashing element of the remote controller will differ according to your AV receiver’s model.

• The remote controller is preconfigured with remote controller presets of different components.

By entering a code from the Remote Control Code list, you can activate the relevant preset for that component.

• When there are multiple codes related to one manufacturer, try and enter them one-by-one until it matches your component.

• Depending on the model and year of your component, compatibility is not guaranteed.

• With some models, the remote controller may not not work or its compatibility may be limited to part of the component’s functionality.

• Besides, it is not possible to add new codes to the existing remote controller presets.

• Though the provided remote control codes are correct at the time of printing, they are subject to change by the manufacturer.

Codes de télécommande

1

Tout en maintenant enfoncé le bouton REMOTE MODE auquel vous souhaitez associer un code, pressez et maintenez enfoncé le bouton [DISPLAY] (pendant environ 3 secondes).

Le bouton REMOTE MODE/le témoin Remote s’allume.

Les noms de boutons sont en manjuscules sur les produits Integra. Par exemple, le bouton « Remote Mode » et le bouton « Display ».

Remarques :

• Les codes de télécommande ne peuvent pas être entrés pour [RECEIVER] et le bouton multi zone.

• Seul les code de télécommande de téléviseurs peuvent être entrés pour [TV].

• À l’exception de [RECEIVER], [TV] et du bouton multi zone, vous pouvez affecter des codes de télécommande de n’importe quelle catégorie pour les boutons REMOTE MODE. Cependant, ces boutons font également office de bouton de sélecteur d’entrée : par conséquent, choisissez un bouton REMOTE MODE correspondant à l’entrée à laquelle vous souhaitez raccorder votre appareil. Par exemple, si vous raccordez votre lecteur CD à l’entrée CD, choisissez [TV/CD] lorsque vous saisissez le code de télécommande.

2

Vous disposez de 30 secondes pour saisir le code de télécommande à cinq chiffres

à l’aide des boutons numérotés.

Le bouton REMOTE MODE/le témoin Remote clignote deux fois.

Si le code de télécommande n’a pas été saisi correctement le bouton REMOTE

MODE/l’indicateur Remote ne clignote qu’une seule fois.

Remarques :

• L’élément clignotant de la télécommande différera selon le modèle de votre ampli-tuner AV.

• La télécommande est préconfigurée avec des préréglages de télécommande de différents appareils. En entrant un code de la liste des codes de télécommandes, vous pouvez activer le préréglage approprié pour cet appreil.

• Quand il y a de multiples codes liés à un fabricant, essayez-les et entrez-les un par un jusqu’à ce que cela corresponde à votre appareil.

• Selon le modèle et l’année de votre appareil, la compatibilité n’est pas garantie.

• Avec certains modèles, la télécommande peut ne pas fonctionner ou sa compatibilité peut être limitée à une partie de la fonctionnalité de l’appareil.

• En outre, il n’est pas possible d’ajouter de nouveaux codes aux préréglages de télécommande existants.

• Bien que les codes de télécommande fournis soient corrects au moment de l’impression de la liste, ils sont susceptibles d’être modifiés par le fabricant.

Remote Control Codes

Códigos de control remoto

1

Manteniendo pulsado el botón REMOTE MODE para el cual desea introducir un código, pulse y mantenga presionado el botón [DISPLAY] (aproximadamente 3 segundos).

Se iluminará el botón REMOTE MODE/indicador Remote.

En los productos Integra, los nombres de los botones aparecen con mayúsculas. Por ejemplo, el botón “Remote Mode” y el botón “Display”.

Notas:

• No podrán introducirse códigos de mando a distancia para [RECEIVER] y el botón multizona.

• Únicamente podrán introducirse códigos de mando a distancia de televisor para el botón [TV].

• Con la excepción de [RECEIVER], [TV] y el botón multizona, se pueden asignar códigos de mando a distancia de cualquier categoría a los botones de REMOTE MODE. No obstante, estos botones también pueden funcionar como botones de selector de entrada; por tanto, seleccione un botón REMOTE MODE que se corresponda con la entrada a la cual está conectado el componente. Por ejemplo, si conecta un reproductor de CD a la entrada de CD, seleccione

[TV/CD] cuando introduzca su código de mando a distancia.

2

Antes de que transcurran 30 segundos, utilice los botones numéricos para introducir el código de mando a distancia de 5 dígitos.

El botón REMOTE MODE/indicador Remote parpadeará dos veces.

Si el código de mando a distancia no se introduce correctamente, el botón REMOTE

MODE/indicador Remote parpadeará una vez despacio.

Notas:

• El parpadeo del mando distancia será distinto según el modelo de receptor de AV.

• El mando a distancia está preconfigurado con los ajustes predeterminados de los distintos componentes. Al introducir un código de la lista de códigos del mando a distancia se puede activar el ajuste predeterminado de ese componente.

• Cuando hay múltiples códigos relacionados con un fabricante, pruebe a introducirlos uno a uno hasta que coincida con su componente.

• Dependiendo del modelo y el año de su componente, la compatibilidad no está garantizada.

• Con algunos modelos, es posible que el mando a distancia no funcione o que su compatibilidad esté limitada a una parte de las funciones del componente.

• Además, no es posible añadir nuevos códigos a los ajustes predeterminados existentes del mando a distancia.

• Los códigos de mando a distancia suministrados son correctos en el momento de la impresión, pero el fabricante puede realizar cambios.

2

Codici del telecomando

1

Tenendo premuto il tasto REMOTE MODE al quale si desidera assegnare il codice, premere e tenere premuto [DISPLAY] (per circa 3 secondi).

Il tasto REMOTE MODE/l'indicatore Remote si accende.

Sui prodotti Integra, i nomi dei tasti sono scritti con l'iniziale maiuscola. Ad esempio, tasto “Remote Mode” e tasto “Display”.

Note:

• I codici di controllo del telecomando non possono essere inseriti per [RECEIVER] e i tasti multi zona.

• Per [TV] è possibile immettere solo codici telecomando del televisore.

• Tranne che per [RECEIVER], [TV], e per il tasto multi zona, è possibile assegnare codici di controllo di ogni categoria per i tasti REMOTE MODE. Tuttavia, tali tasti fungono anche da tasti del selettore d'ingresso, quindi scegliere un tasto REMOTE MODE che corrisponda all'ingresso al quale viene collegato il dispositivo. Per esempio, se si collega il lettore CD all'ingresso CD, scegliere il [TV/CD] quando si immette il relativo codice telecomando.

2

Entro 30 secondi utilizzare i tasti numerici per inserire il codice telecomando a 5 cifre.

Il tasto REMOTE MODE/l'indicatore Remote lampeggia due volte.

Se il codice telecomando non viene inserito correttamente, il tasto REMOTE

MODE/l'indicatore Remote lampeggia lentamente una volta.

Note:

• L'elemento lampeggiante del telecomando varia a seconda del modello del ricevitore AV.

• Il telecomando è preconfigurato con preselezioni per diversi apparecchi. Inserendo un codice dall'elenco dei codici telecomando, è possibile attivare la relativa preselezione per tale apparecchio.

• Se sono presenti più codici relativi allo stesso produttore, provare a inserirli uno a uno finché non si arrivi al codice corrispondente dell'apparecchio.

• A seconda del modello e dell'anno dell'apparecchio, la compatibilità non è garantita.

• Con alcuni modelli, il telecomando può non funzionare o la sua compatibilità può essere limitata a una parte della funzionalità dell'apparecchio.

• Inoltre, non è possibile aggiungere nuovi codici alle preselezioni esistenti del telecomando.

• I codici telecomando specificati sono validi alla data della stampa del presente documento, ma sono soggetti a variazioni da parte del produttore.

Remote Control Codes

Fernbedienungscodes

1

Halten Sie die REMOTE MODE-Taste gedruckt, fur die Sie den Code eingeben mochten, und drucken Sie (ca. 3 Sekunden lang) die [DISPLAY]-Taste.

Die REMOTE MODE-Taste/Remote-Anzeige leuchtet.

Bei den Integra-Produkten werden die Namen der Tasten groß geschrieben. Zum

Beispiel „Remote Mode“ (Fernbedienungsmodus)-Taste und „Display“-Taste.

Hinweise:

• Der Fernbedienungscode kann nicht [RECEIVER] und der Multi-Zonen-Taste zugeordnet werden.

• Der Taste [TV] können nur Fernbedienungscodes für einen Fernseher zugeordnet werden.

• Abgesehen von [RECEIVER], [TV] und der Multi-Zone-Taste, können die

Fernbedienungscodes jeder Kategorie den REMOTE MODE-Tasten zugewiesen werden.

Allerdings dienen diese Tasten auch als Quellenwahltasten. Wählen Sie also nach Möglichkeit eine REMOTE MODE-Taste, die dem Eingang zugeordnet ist, an den Sie die betreffende Quelle angeschlossen haben. Wenn Sie z.B. einen CD-Player an den CD-Eingang anschließen, sollten

Sie [TV/CD] wenn Sie den Fernbedienungscode eingeben.

2

Geben Sie mit den Zifferntasten innerhalb von 30 Sekunden den 5-stelligen

Herstellercode ein.

Die REMOTE MODE-Taste/Remote-Anzeige blinkt zwei Mal.

Wenn der Fernbedienungscode nicht ordnungsgemäß eingegeben wurde, blinkt die

REMOTE MODE-Taste/Remote-Anzeige einmal langsam.

Hinweise:

• Das blinkende Element auf der Fernbedienung unterscheidet sich je nach AV-Receiver-Modell.

• Die Fernbedienung ist mit den Voreinstellungen der Fernbedienung der verschiedenen

Komponenten vorkonfiguriert. Indem ein Code aus der Liste der Fernbedienungscodes eingegeben wird, können Sie die entsprechende Voreinstellung für die Komponente aktivieren.

• Wenn es mehrere Codes gibt, die sich auf einen Hersteller beziehen, versuchen Sie sie einzeln einzugeben, bis einer mit Ihrer Komponente übereinstimmt.

• Dies hängt vom Modell und Herstellungsjahr Ihrer Komponente ab und die Kompatibilität ist nicht garantiert.

• Es kann sein, dass bei einigen Modellen die Fernbedienung nicht funktioniert oder ihre

Kompatibilität sich auf nur auf Teile der Funktionalität der Komponente beschränkt.

• Abgesehen davon ist es nicht möglich, den bestehenden Voreinstellungen der Fernbedienung neue Codes hinzuzufügen.

• Obwohl die angegebenen Fernbedienungscodes dem Stand bei Drucklegung entsprechen, sind

Änderungen durch den Hersteller vorbehalten.

3

Afstandsbedieningscodes

1

Houd terwijl u de REMOTE MODE toets ingedrukt houdt waarvoor u een code wilt toewijzen de [DISPLAY] toets ingedrukt (ongeveer 3 seconden).

De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje afstandsbediening gaat branden.

Op producten van Integra staan de namen van de toetesn in hoofdletters. Bijvoorbeeld, de toetsen “Remote Mode” en “Display”.

Opmerkingen:

• Er kunnen geen afstandsbedieningscodes worden ingevoerd voor [RECEIVER] en de multi zone-toets.

• Alleen TV afstandsbedieningscodes kunnen worden ingevoerd voor [TV].

• Behalve voor [RECEIVER], [TV] en de multi zone-toets, kunnen afstandsbedieningscodes vanuit elke categorie worden toegewezen aan de REMOTE MODE toetsen. Deze toetsen werken overigens ook als ingangsselectortoetsen, kies dus een REMOTE MODE toets die overeenkomt met de ingang waarop u uw component wilt aansluiten. Kies indien u bijvoorbeeld uw CD-speler aansluit op de CD-ingang de [TV/CD] toets bij het invoeren van de afstandsbedieningscode.

2

Gebruik binnen 30 seconden de cijfertoetsen om de 5-cijferige afstandsbedieningscode in te voeren.

De toets REMOTE MODE (afstandsbedieningsmodus) / Het indicatielampje afstandsbediening knippert tweemaal.

Indien de afstandsbedieningscode niet met succes wordt ingevoerd, zal de toets

REMOTE MODE/Remote-indicator eenmaal traag knipperen.

Opmerkingen:

• Het knippergedeelte van de afstandsbediening zal verschillen ten opzichte van het model van uw AV-receiver.

• De afstandsbediening is voorgeprogrammeerd met voorkeuzetoetsen van verschillende componenten. Door het invullen van een code uit de afstandsbediening codelijst kunt u de voorkeuzetoets voor die component activeren.

• Wanneer er meerdere codes gerelateerd zijn aan één fabrikant, probeer deze dan een voor een totdat de juiste code overeenkomt met uw component.

• Afhankelijk van het model en het bouwjaar van uw component is de compatibiliteit niet gegarandeerd.

• Bij sommige modellen werkt de afstandsbediening mogelijk niet of is de compatibiliteit ervan beperkt tot een deel van de functionaliteit van de component.

• Daarnaast is het niet mogelijk om nieuwe codes aan de bestaande voorkeuzetoetsen van de afstandsbediening toe te voegen.

• Hoewel de gegeven afstandsbedieningscodes correct zijn op het moment van afdrukken, kunnen deze door de fabrikant gewijzigd worden.

Remote Control Codes

Fjärrstyrningskoder

1

Håll ned knappen för det REMOTE MODE som du vill tilldela en kod samtidigt som du trycker och håller ned [DISPLAY] (i cirka 3 sekunder).

REMOTE MODE-knapp/Fjärrindikatorlampa.

På Integra-produkter, är knappnamnens begynnelsebokstav en versal. Till exempel,

”Fjärrläge”-knapp och ”Display”-knapp.

Anmärkningar:

• Fjärrkontrollkoder kan inte anges för knapparna [RECEIVER] och flerzonsknappen.

• Endast fjärrkontrollkoder för tv kan anges för [TV].

• Förutom [RECEIVER], [TV] och flerzonsknappen, kan fjärrkontrollkoder för vilken som helst kategori tilldelas för knapparna REMOTE MODE. Dessa knappar fungerar dock även som ingångväljarknappar, så använd en knapp för REMOTE MODE som motsvarar ingången som du ansluter utrustningen till. Till exempel, om du ansluter din CD-spelare till CD-ingången ska du välja [TV/CD] när du anger dess fjärrkontrollkod.

2

Använd sifferknapparna för att ange den femsiffriga koden inom 30 sekunder.

REMOTE MODE-knapp/Fjärrindikatorlampa blinkar två gånger.

Om fjärrkontrollkoden inte ställdes in, blinkar REMOTE MODEknappen/fjärrindikatorn långsamt en gång.

Anmärkningar:

• Det blinkande elementet på fjärrkontrollen skiljer sig åt beroende på din modell av AV-receiver.

• Fjärrkontrollen har förkonfigurerats med förvalda kanaler på fjärrkontrollen för olika komponenter. Genom att ange en kod från fjärrkontrollkodlistan, kan du aktivera relevanta förvalda kanaler för den utrustningen.

• När det finns flera olika koder för en tillverkare ska du försöka att ange dem en och en tills de stämmer överens med din utrustning.

• Beroende på utrustningens modell och årgång, går det inte att garantera kompatibilitet.

• På vissa modeller kan det hända att fjärrkontrollen inte fungerar eller så kan dess kompatibilitet vara begränsad till en del av utrustningens funktion.

• Dessutom går det inte att lägga till nya koder till fjärrkontrollens existerande förvalda kanaler.

• Även om erhållna fjärrkontrollkoder är korrekta vid tryckningen, kan de ändras av tillverkaren.

4

遙控代碼

1

在按住想指定編碼的 REMOTE MODE (遙控模式)按鈕時,同時按住

[DISPLAY] (顯示)(約 3 秒)。

REMOTE MODE (遙控模式)按鈕 / 遙控指示燈亮起。

在 Integra 系列產品上,按鈕名稱為大寫。 例如,「Remote Mode」(遙控模式)

按鈕和 「Display」(顯示)按鈕。

注意:

[RECEIER] (接收機)和多區域按鈕不能輸入遙控編碼。

• 您只能為 [TV] (電視)輸入電視遙控編碼。

• 除 [RECEIVER] (接收機)、[TV] (電視)和多區域按鈕外,您可針對 REMOTE MODE

(遙控模式)按鈕指定任何類別的遙控編碼。 但是,這些按鈕仍可用作為輸入選擇器按

鈕,因此,請選擇與您設備所連接輸入接口對應的 REMOTE MODE 按鈕。 例如,如果

要將 CD 播放機連接到 CD 輸入源上,則需在輸入遙控編碼時選擇 [TV/CD]。

2

在 30 秒內,使用數字按鈕輸入 5 位數的遙控編碼。

REMOTE MODE (遙控模式)按鈕 / 遙控指示燈閃爍兩次。

如果無法成功輸入遙控編碼,REMOTE MODE (遙控模式)按鈕 / 遙控指示燈

會慢慢地閃爍一次。

注意:

• 視您的 AV 接收機型號而定,遙控器的閃爍元件會有不同。

• 遙控器已預先設定有不同設備的遙控器預設值。 透過輸入遙控編碼清單中的編碼,您

可啟用該設備的相關預設值。

當有多個編碼與單一製造商相關時,請嘗試一個接著一個輸入,直到與您的設備對應

為止。

• 視設備的型號和年份而定,並不保證與本公司產品相容。

• 在某些型號上,遙控器可能無法作用,或是其相容性限於部份設備功能。

• 除此之外,您無法新增編碼至現有的遙控器預設值。

• 雖然所提供之遙控編碼在本文件列印時為正確,製造商仍可能會對其作出修改。

Remote Control Codes

遥控代码

1

按住想指定编码的 REMOTE MODE (遥控模式)按钮的同时,按住 [DISPLAY

(显示)] (大约 3 秒钟)。

REMOTE MODE (遥控模式)按钮 / 遥控指示灯亮起。

Integra 产品上的按钮名称单词首字母大写。例如,“Remote Mode (遥控模

式)”按钮和 “Display (显示)”按钮。

注意:

[RECEIVER (接收机)] 和多区域按钮不能输入遥控编码。

只能为 [TV (电视)] 输入电视遥控编码。

除 [RECEIVER (接收机)]、[TV (电视)] 和多区域按钮外,不能为 REMOTE MODE (遥

控模式)按钮指定任何类别的遥控编码。 但是,这些按钮仍可用作输入选择器按钮,因

此,选择与设备所要连接的输入端对应的 REMOTE MODE(遥控模式) 按钮。 例如,如果

要将 CD 播放机连接到 CD 输入端,应在输入遥控编码时选择 [TV/CD (电视 /CD)]。

2

在 30 秒内,使用数字按钮输入 5 位数的遥控编码。

REMOTE MODE (遥控模式)按钮 / 遥控指示灯闪烁两次。

如果不能顺利输入遥控编码,REMOTE MODE (遥控模式)按钮 / 遥控指示灯会

缓慢闪烁一次。

注意:

根据 AV 接收机产品类型的不同,遥控器闪烁元素将会不同。

遥控器采用不同设备的遥控器预设进行预配置。通过从遥控器编码列表输入编码,便

可激活相应设备的相关预设。

单个制造商关联多个编码时,请尝试逐个输入,直至符合当前设备。

根据设备的产品类型和年份的不同,无法保证兼容性。

对于某些产品类型,遥控器可能无法工作或其兼容性可能受到部分设备功能性的限制。

此外,可能无法将新的编码追加到现有的遥控器预设。

尽管付印时所提供的遥控编码是正确的,但制造商会随时更改。

5

Dedicated Onkyo Receiver

Default 62503

Zone 2

Zone 3

62506

62507

Cable Set Top Box

ADB 02254, 02769

Aon

Arris

02769

02187

AT&T

Bright House

BT Vision

Cable & Wireless

Cable One

00858

01376, 01877

02294

01068

01376, 01877

Cablecom

Cablevision

Charter

Cisco

Com Hem

Comcast

Cox

Daeryung

Digeo

DX Antenna

France Telecom

Freebox

Fujitsu

Humax

Insight

J:COM

Knology

Kreatel

Macab

Mediacom

01582

01376, 01877

01376, 01877, 02187

01877, 00858, 01982,

02345, 02378

00817, 00660, 01666,

02015, 02447

01376, 01877, 01982,

02187

01376, 01877

01877

02187

01500

00817

01482

01497

00660, 02142, 02447,

03051, 03053

01376, 01877

03051, 03053

01877

01385

00817

01376, 01877

Cable Set Top Box

mio TV

Motorola

Moxi

NEC

02802

01376, 00858, 01562,

01982, 01998, 02378

02187

01496

Neuf TV

Noos

NTL

Numericable

Ono

Optus

Orange

Pace

Panasonic

Philips

03107

00817

01068, 01060

02767

01068, 01562

01060

00817

01376, 01877, 01068,

01060, 01982

01488, 01982

00817, 01582, 02294,

02767

01877, 01500 Pioneer

RCN

Rogers

Sagem

Samsung

Scientific Atlanta

SFR

Shaw

SingTel

Sony

Stofa

Suddenlink

Sumitomo

Telewest

TeliaSonera

Telus

Thomson

Time Warner

01376

01877

00817

01877, 01060, 01666,

02015, 02774

01877, 00858, 01982,

02345

03107

01376

01998, 02802

01460

02015

01376, 01877

01500

01068

01385

02345

01582, 01982, 02769

01376, 01877, 02187

Cable Set Top Box

Toshiba

UPC

01509

01582

Verizon

Videotron

Virgin Media

02378

01877

01068, 01060

Visiopass

VTR

WideOpenWest

Ziggo

00817

01376

01877

00660, 01666, 02015,

02142, 02447, 02774

Insight

J:COM

Knology

Mediacom

Motorola

Moxi

Numericable

Pace

Panasonic

Philips

Pioneer

Rogers

Cable/PVR Combination

Arris 02187

Bright House

Cable One

Cablevision

Charter

Cisco

Comcast

Cox

Digeo

Freebox

Humax

01376, 01877

01376, 01877

01376, 01877

01376, 01877, 02187

01877, 01982

01376, 01877, 01982,

02187

01376, 01877

02187

01482

02142, 03051, 03053

01376, 01877

03051, 03053

01877

01376, 01877

01376

02187

02767

01877

01982

01582, 02767

01877

01877

6

Remote Control Codes

Cable/PVR Combination

Samsung

Scientific Atlanta

01877

01877, 01982

Shaw

Suddenlink

Thomson

01376

01376, 01877

01582

Time Warner

UPC

Videotron

VTR

WideOpenWest

Ziggo

01376, 01877, 02187

01582

01877

01376

01877

02142

IPTV

ADB

Aon

AT&T

BT Vision

Canal+

Cisco

Kreatel mio TV

Motorola

Neuf TV

Pace

Scientific Atlanta

SFR

SingTel

TeliaSonera

Telus

Thomson

Verizon

IPTV/PVR Combination

ADB

Aon

02769

02769

02254, 02769

02769

00858

02294

02657

00858, 02345, 02378

01385

02802

01376, 00858, 01998,

02378

03107

02657

00858, 02345

03107

01998, 02802

01385

02345

02769

02378

IPTV/PVR Combination

AT&T 00858

BT Vision

Cisco

Kreatel

Motorola

Neuf TV

Philips

Scientific Atlanta

SFR

Verizon

02294

00858, 02345, 02378

01385

00858, 02378

03107

02294

00858

03107

02378

CD

Advantage

AH!

Aiwa

Arcam

Atoll Electronique

Audio Research

Audiolab

Audiomeca

Audioton

AVI

Balanced Audio

Technology

Cairn

70032

70157

70157

70157

70157

70157

70157

70157

70157

70157

70157

70157

California Audio Labs 70029, 70303

Cambridge 70157

Cambridge Audio

Carver

70157

70157

CCE

Cyrus

Denon

DKK

DMX Electronics

70157

70157

70626, 70766

70000

70157

Dynaco

Genexxa

70157

70000, 70032

Magnavox

Marantz

Matsui

MCS

Memorex

Meridian

Micromega

Miro

Mission

Myryad

NAD

Naim

NSM

Onkyo

Optimus

Panasonic

Philips

Pioneer

CD

Goldmund

Grundig

Harman/Kardon

Hitachi

Integra

JVC

Kenwood

Krell

Linn

Loewe

Polk Audio

Primare

Proton

QED

Quad

Quasar

Radiola

RCA

70157

70157

70157

70157

70157

70029

70157

70032

70157

70157

70157

70032

71817, 70101

70072

70626, 70157, 70036

70157

70157

70157

70157

70626, 70029, 70157

70157

70029

70032

70157

70157

70000

70157

70157

70000, 70721

70157

70157

71817

70000, 70032

70029, 70303

70626, 70157

70032, 70101

CD

Restek

Revox

Rotel

SAE

Sansui

SAST

Siemens

Silsonic

Simaudio

Sonic Frontiers

Sony

Sylvania

TAG McLaren

Tandy

Technics

Thorens

Thule Audio

Traxdata

Universum

Victor

Wards

Yamaha

Zonda

CD-R

Denon

JVC

Kenwood

Marantz

Onkyo

Philips

Sony

MD

Onkyo

Sony

7

70157

70157

70157

70157

70157

70157

70157

70036

70157

70157

70490, 70000

70157

70157

70032

70029, 70303

70157

70157

70626

70157

70072

70000, 70032, 70157

70490, 70032, 70036

70157

70626, 70766

70072

70626

70626

71323

70626

70000

70868

70490, 70000

MD

Yamaha

Marantz

Myryad

Onkyo

Optimus

Philips

Pioneer

Polk Audio

Radiola

RCA

Revox

Sansui

Sony

Thorens

Victor

Wards

Yamaha

Cassette Deck

Aiwa

Arcam

Audiolab

Carver

Denon

Grundig

Harman/Kardon

Inkel

JVC

Kenwood

Magnavox

Accessory

Apple

Jamo

Logitech

Onkyo

Remote Control Codes

70490

81115

82228

82182

82990, 81993, 82351

40029

40076

40029

40029

40076

40029

40029

40070

40244

40070

40029

40029

40029

42157

40027

40029

40027

40029

40029

40027

40029

40029

40243

40029

40244

40027, 40029

40097

Accessory

Polk Audio 82228

Video - Accessory

ADB

Aon

Apple

AT&T

BT Vision

Canal+

Cisco

Kreatel mio TV

Motorola

Neuf TV

Pace

Philips

Scientific Atlanta

SFR

SingTel

TeliaSonera

Telus

Thomson

Verizon

02254, 02769

02769

02615

00858

02294

02657

00858, 02345, 02378

01385

02802

01376, 00858, 01998,

02378

03107

02657

02294

00858, 02345

03107

01998, 02802

01385

02345

02769

02378

Receiver

Onkyo 52503

Satellite Set Top Box

@sat 01300

@Sky

Acoustic Solutions

01334

01284

ADB

Akura

00642, 00887, 01259

01626

Alba

Allvision

01284

01334

Satellite Set Top Box

Amstrad 00847, 01175, 01662,

01693

Ansonic 02418

Arnion

ASCI

AssCom

Astro

Atlanta

Atsat

AtSky

Audiola

Aurora

01300

01334

00853

00173, 01100

02418

01300

01334

02418

00879, 00642, 01433

Austar

Avanit

Awa

Axil

Axitronic

Balmet

Bell ExpressVu

Belson

Big Sat

Black Diamond

Blaupunkt

Boshmann

Boston

Boxer

British Sky

Broadcasting

BskyB

Bush

Canal Digital

Canal Satellite

Canal+

CanalSat

Centrex

00879, 00642, 01259

01631

02418

01413, 01457, 02418

01626

01457

00775

02418

01457

01284

00173

01413, 01631

01251

01458

00847, 01175, 01662

00847, 01175, 01662

01284, 01291, 01626,

01645

00853, 01334

00853, 02657

00853, 02657

00853, 02657

01457

Satellite Set Top Box

CGV 01413, 01567

Chess

CityCom

Clatronic

Clayton

Com Hem

Comag

Comsat

Coship

Crown

01334, 01626

01176

01413

01626

01176, 01915

01413

01413

01457

01284

CS

Cyfra+

Cyfrowy Polsat

D-box

01631

01409

00853, 02527

00723, 01114

Dantax

Denver

Dgtec

Dick Smith

Electronics

01626

02418

01242, 01631, 02418

02418

Digi Raum Electronics 01176

Digiality 01334

Digifusion

Digihome

DigiLogic

DigiQuest

Digisky

DigitalBox

Digiwave

DirecTV

Dish Network

Dishpro

DishTV

DRE

Dream Multimedia

DSE

DSTV

01645

01284

01284

01300, 01457, 01631

01457

01100, 01631

01631

01377, 00099

00775

00775

01300

01176

01237

02280, 02418

00879, 00642, 01433

8

Remote Control Codes

Satellite Set Top Box

Durabrand 01284

Echostar 00775, 00853, 01323,

01409, 02527

Eco-Star

Edision

Elap

Elbe

Energy Sistem

Engel

EuroLine

Europhon

Europsat

Expressvu

Fagor

Ferguson

Finlux

Fly Com

FMD

Foxtel

Freesat

01413

01631

01413, 01567

02418

01631, 02418

01251

01251

01334

01413, 01611

00775

01611

01291

01626

01457

01413, 01457

00879, 01176, 01356

02408

Fuba

Galaxis

General Satellite

Globo

GOI

Gold Box

Gold Vision

GoldMaster

Goodmans

Gradiente

Grandin

Grocos

Grundig

Haier

Hallo

00173, 01251

00853, 00879

01176

01251, 01334, 01626

00775

00853

01631

01334

01284, 01291

00099, 00887

01626

01409, 01457

00847, 00853, 00173,

00879, 01284, 01291

02418

01626

Satellite Set Top Box

Hama 01567

Hanseatic

Hirschmann

Hitachi

Hornet

HTS

Humax

ID Digital

ID Sat

ILLUSION sat

Imperial

01100

00173

01284

01300

00775

01377, 01176, 01427,

01675, 01808, 01882,

01915, 02144, 02408,

02616

01176

01334

01631

01195, 01334

Indovision iNETBOX

Inno Hit

Innova inVion iotronic

ISkyB

ITT

ITT Nokia

Jadeworld

Jaeger

JVC

KabelBW

Kaon

Kathrein

Kenwood

Koenig

Kreiling

Kreiselmeyer

L&S Electronic

LaSAT

Lava

00887

01237

01626

00099

02418

01413

00887

02418

00723

00642

01334

00775

01195, 01882, 01915

01300

00173, 01561, 01567

00853

01631

01626

00173

01334

00173

01631

MySky

NEOTION

Netsat

Nikko

Nokia

Nordmende

NPG

Onn

Optex

Optus

Orbis

Orbitech

Satellite Set Top Box

Leiko 01626

Lemon

Lenoxx

Linsar

Listo

Lodos

Logik

Macab

Manhattan

Maspro

01334

01611

01284

01626

01284

01284

00853

01300

00173

Matsui

Maximum

Mediabox

Mediacom

MediaSat

Medion

MegaSat

Metronic

00173, 01284, 01626

01334

00853

01206

00853

01334, 01626

01631

01334, 01413, 01631,

02418

00173 Metz

Moserbaer

Movistar

Multichoice

01251

02527, 02761

00879, 00642, 01433,

02059, 02060

01356, 01693, 01850

01334

00099, 00887

00723

00853, 00723, 01223

01611

01631

01284

01413, 01611, 01626

00879, 01356

01334

01100, 01195

Premiere

Pro Basic

Proline

QNS

RCA

Regal

Roadstar

Rollmaster

Rownsonic

SAB

Sagem

Saivod

Samsung

Satellite Set Top Box

Pace 00847, 00853, 00887,

01175, 01323, 01356,

01423, 01662, 01693,

01850, 02059, 02060,

02211, 02657

Pacific

Palcom

01284

01409, 01611

Panasat

Panasonic

Panda

Pass peeKTon

Philips

Phoenix

Pino

Pioneer

PMB

00879, 01433

00847, 01304, 01404,

03099

00173

01567

01457, 02418

00099, 00853, 00173,

01114, 00887, 00133,

02211

02418

01334

00853, 01308

01611

Sansui

Sanyo

Sat Control

00723

00853

01284

01404

01291

01251

00853

01413

01567

01251, 01300, 01631

01114

02418

01377, 00853, 01175,

01206, 01458, 01662,

02986

01251

01626

01300

9

Remote Control Codes

Satellite Set Top Box

Sat Industrie 01611

SAT+

Satplus

SatyCon

Schaub Lorenz

Schneider

Schwaiger

Sedea Electronique

SEG

Servimat

ServiSat

Shark

Sherwood

Siemens

Sigmatek

SKY

SKY Brazil

SKY Deutschland

SKY Italia

SKY New Zealand

SKY PerfecTV!

Sky XL

Sky+

Skymaster

Skymax

Skyplus

SkySat

Skyvision

SM Electronic

Smart

SmartVision

Sony

01409

01100

01631

02418

01206, 01251

01334, 01457, 01631

01206, 01626

01251, 01284, 01626

01611

01251

01631

01409

00173, 01334, 01626,

02418

02418

00099, 00847, 00887,

01175, 01662, 01693,

01850, 02754

00887

02754

00853, 01693, 01850

02211

02299, 02616, 03099

01251

01175, 01662

01334, 01409, 01567,

01611

01413

01175, 01334

01100

01334

01409

01404, 01413, 01631

01457

00847, 00853, 01558,

02299

Satellite Set Top Box

Star 00887

Stream System

Strong

Sunny

Sunstar

Supernova

Supratech

Systec

Sytech

TBoston

01300

00853, 00879, 01284,

01300, 01409, 01626,

02418

01300

00642

00887

01413

01334

02418

01251, 02418

Teac

Technical

Technika

TechniSat

Technosat

Techwood

TELE System

Telefonica

Telestar

Televes

Televisa

Tevion

Thomson

Tonna

Topfield

Toshiba

Trevi

Triax

Tricolor TV

True Visions

Twinner

01251

01626

01284

01100, 01195

01206

01251, 01284, 01626

01251, 01409, 01611

02527, 02761

01100, 01195, 01251,

01334, 01626

01300, 01334

00887

01409

00847, 00853, 01175,

01046, 01291, 01662

01611

01206

01284

01251

00853, 01251, 01291,

01413, 01611, 01626,

01631

01176

02408

01611

Satellite Set Top Box

UBC 00642

UEC

United

Unitymedia

Universum

Variosat

VEA

Vestel

Viasat

Vision

00879, 01356

01251, 01626, 02418

01882

00173, 01251

00173

02418

01251, 01284

01195

01626

Visiosat

Vitecom

Vivax

Volcasat

Wavelength

Wharfedale

Wisi

Worldsat

Woxter

Xsat

Xtreme

Yakumo

Yes

Zehnder

Zinwell

01413, 01457

01413

02418

02418

01413

01284

00173

01251

02418

00847, 01323

01300

01413

00887

01251, 01334, 01413,

01631

02280, 02761

Satellite Set Top Box

@sat 01300

SAT/PVR Combination

@sat

Amstrad

Atsat

Bell ExpressVu

British Sky

Broadcasting

01300

01175, 01662, 01693

01300

00775

01175, 01662

ID Sat iNETBOX

Kaon

Kathrein

Maximum

Mediacom

MegaSat

Movistar

Multichoice

MySky

NEOTION

Pace

SAT/PVR Combination

BskyB 01175, 01662

Bush

Canal Satellite

Canal+

CanalSat

Cyfrowy Polsat

Digifusion

DigiQuest

DirecTV

Dish Network

01645

02657

02657

02657

02527

01645

01300

01377, 00099, 20739

00775

Dishpro

Dream Multimedia

Echostar

Edision

Expressvu

Foxtel

Humax

00775

01237

00775, 02527

01631

00775

01356

01176, 01427, 01675,

01808

01334

01237

01300

01561

01334

01206

01631

02527

02059, 02060

01356, 01693, 01850

01334

Panasonic

Philips

Samsung

Sat Control

01175, 01356, 01423,

01662, 01693, 01850,

02059, 02060, 02211,

02657

01304, 03099

00099

01175, 01206, 01662

01300

10

Remote Control Codes

SAT/PVR Combination

Schneider 01206

Sedea Electronique

SKY

SKY Deutschland

SKY Italia

SKY New Zealand

SKY PerfecTV!

Sky+

Skyplus

Smart

Sony

01206

01175, 01662, 01693,

01850, 02754

02754

01693, 01850

02211

02299, 03099

01662

01175, 01334

01631

02299

Stream System

Strong

Sunny

TechniSat

Technosat

Telefonica

Telestar

Thomson

Topfield

Viasat

Xtreme

01300

01300

01300

01195

01206

02527

01195

01175, 01662

01206

01195

01300

Television

A.R. Systems

Accent

Acer

Acoustic Solutions

Action

Addison

AEG

Agfaphoto

Aiko

Aim

10556, 10037

10037

11339

11037, 11667

10650

10653

11037, 11324

12719

10037

10037, 10499

Television

Akai

Akiba

Akito

Akura

Alba

Alien

Allstar

Amstrad

Anam

Anam National

Andersson

Anitech

Ansonic

AOC

Ardem

Arena

Aristona

ART

Art Mito

Asberg

Astra

ATD

Atlantic

Audiosonic

Audiovox

Audioworld

Aventura

Axxon

Baird

Bang & Olufsen

Barco

10178, 10556, 10037,

10714, 10715, 10208,

11675

10037

10037

10171, 10037, 10714,

10668, 11037, 11363,

11585, 11667, 11709

10037, 10714, 10668,

11037, 11585

11037

10037

10171, 10037, 11037

10037

10037, 10650

11585

10037

10037, 10668

10178, 10625, 11365

10037, 10714

10037

10556, 10037

11037

11585

10037

10037

10698

10037

10037, 10714, 10715

11564

10698

10171

10714

10208

10565

10556

Boca

Boman

Bork

BPL

Brandt

Brimax

Brinkmann

Brionvega

Bush

Byd:sign

Camper

Carad

Carena

Carrefour

Cascade

Television

Basic Line

Baur

Beaumark

Beijing

Beko

Belson

Belstar

Beon

Berthen

Bestar

Bexa

Black Diamond

Blaupunkt

Blue Sky

10556, 10037, 10668,

11037

10037, 10195, 10512

10178

10208

10037, 10714, 10715,

11652

10698

11037

10037

10556, 10668

10037

12493

11037

10195

10556, 10037, 10625,

10714, 10668, 11037,

10715, 10499, 11324,

11363, 11652, 11709

11652

11324

11363

10037, 10208

10625, 10714, 10560

11709

10037, 10668

10037

10556, 10037, 10714,

10668, 11037, 10698,

10208, 11585, 11652,

11667, 12719

12140, 12209

10037

10668, 11037

10037

10037

10037

Television

Casio

Cathay

CCE

Centrum

Centurion

Changhong

Chimei

Clarivox

Classic

Clatronic

Clayton

Condor

Conrowa

Contec

Cosmel

CPTEC

Crown

Cyberpix

D-Vision

Daewoo

Dansai

Dantax

Datsura

Dawa

Daytron

De Graaf

DEC

Decca

Denver

Desmet

Diamant

Diamond

11

10037

10037

10037

11037

10037

10508

11666

10037

10499

10037, 10714, 11324

11037

10037

10698

10037

10037

10625, 11363

10037, 10714, 10668,

11037, 10715, 10208,

11652

11667

10556, 10037

10178, 10556, 10037,

10634, 10499, 12098

10037, 10208

10714, 11037, 10715,

11652

10208

10037

10037

10208

11709

10037

10037, 11709

10037

10037

10698

Envision

Epson

Television

Dick Smith

Electronics

Digatron

Digihome

Digiline

Digitek

Digitor

Dixi

DL

DMTech

Domeos

Drean

DSE

Dual

Durabrand

Dux

DX Antenna

Dynatron

Dynex e-motion

E:max

Easy Living

ECE

Elbe

Electrograph

Element

Elfunk

ELG

Elin

Elite

Emerson

Remote Control Codes

10698

10037

11667

10037, 10668

11709

10037, 10698

10037

11363

12001

10668

10037

10698

10037, 11037, 11585,

11667

10178, 10171, 10714,

11037, 11652

10037

11817, 13817

10037

12049

11709

11324

11666, 11709

10037

10556, 10037

11755

11886

11037

10037

10037

10037

10178, 10171, 10037,

10714, 10668, 11394,

11864, 11886

11365, 11506

11379

Fisher

Flint

Formenti

Fraba

Friac

Fujicom

Fujitsu

Fujitsu Siemens

Funai

G-Hanz

Gaba

Galaxi

Galaxis

Gateway

GE

GEC

Television

Erres

ESA

ESC

Euroman

Europa

Europhon

Evesham

Excello

Exquisit

Ferguson

Fidelity

Finlandia

Finlux

Firstline

10037

10171

10037

10037

10037

10037

11248, 11667

11037

10037

10037, 10625, 10560,

10195, 11037, 11585

10171, 10037, 10512

10208

10556, 10037, 10714,

10715, 11248, 11667

10556, 10037, 10714,

10668, 11037, 10208,

11363

10208

10037

10037

10037

10037, 10499

11709

10809

10809, 11248, 11666

10171, 10714, 10668,

11037, 11394, 11666,

11817, 13817

11363

11037

10037

10037

11755

10178, 11454, 10625,

10560

10037

Television

Genesis

Genexxa

GFM

Godrej

Goldfunk

GoldStar

Goodmans

Gorenje

Gradiente

Graetz

Granada

Grandin

Grundig

GVA

H & B

Haier

Hallmark

Hankook

Hanseatic

Hantarex

Hantor

Harwood

Hauppauge

HB

HCM

Highline

Hinari

Hisawa

10037

10037

10171, 11864, 11886

11585

10668

10178, 10037, 10714,

10715

10556, 10037, 10625,

10714, 10560, 10668,

10634, 11037, 10499,

11585, 11667

11585

10037

10714

10037, 10560, 10208

10556, 10037, 10714,

10668, 11037, 10715,

11652

10556, 10037, 10195,

11223, 11667, 12625

11363, 12098

12001

10037, 10698, 10508

10178

10178

10556, 10037, 10625,

10714, 10634, 10499,

12001

10037

10037

10037

10037

11324

10037

10037

10037, 10208

10714

Television

Hisense

Hitachi

Integra

Interbuy

Interfunk

Internal

Intervision

Irradio

IRT

Isukai

ITS

ITT

ITT Nokia

Hitachi Fujian

Hitec

Hoeher

Hornyphon

Hugoson

Humax

Hypson

Hyundai

Iberia

ICE iLo

Imperial

Indiana

Ingelen

Inno Hit

Innova

Insignia

12

10556, 10508, 10208,

11363, 12098

10150, 10178, 10037,

10634, 11037, 10508,

10499, 10578, 11576,

11585, 11643, 11667,

11691, 12433

10150

10698

10714

10037

11666

11295

10556, 10037, 10714,

10668, 11037, 10715

11037, 10698

10037

10037

11394

10037

10037

10714

11037, 11585

10037

10171, 11423, 11564,

12049

11807, 13100, 13500

10037

10037, 10512

10556

10037

10037

10698

10037

10037

10208

10208

Liesenkoetter

Television

ITV

JGC

Jinfeng

Jinxing

JMB

Jubilee

JVC

Kaisui

Karcher

Kathrein

Kendo

Kennex

Kioto

Kiton

KLL

Kneissel

Koenig

Kolin

Kolster

Konka

Korpel

Kosmos

Kunlun

L&S Electronic

Lavic

Lavis

Lecson

Lenco

Leyco

LG

Remote Control Codes

10037

11709

10208

10556, 10037, 10698

10556, 10634, 10499

10556

10650, 10653, 10508,

11428, 11601, 12271

10037

10714, 11324

10556

10037, 11037, 11585

11037

10556

10037, 10668

10037

10556, 10037, 10499

10037

10150, 10037, 11610,

11755

10037

10037, 10714

10037

10037

10208

10714

11363

11037

10037

10037, 11037

10037

10178, 10556, 10037,

10714, 10715, 10698,

11423, 11768, 11840,

12182, 12358, 12424,

12834

10037

Television

Lifetec

Linsar

Local India TV

Local Malaysia TV

Lodos

Loewe

Logik

Logix

Luma

Lumatron

Lumenio

Lux May

Luxor

LXI

M Electronic

Madison

Magnavox

Magnum

Manesth

Manhattan

Marantz

Mark

Master's

Mastro

Masuda

Matsui

Matsushita

Maxent

Maxess

Meck

Mediator

10037, 10714, 10668,

11037, 12001

11585

10208

10698

11037

10037, 10512, 11884

11037, 10698

10668

11037

10037, 10668

10037

10037

11037, 10208

10178

10037, 10714, 10634,

10195, 10512, 11652

10037

10171, 11454, 11365,

11506, 11755, 11867,

12372

10037, 10714, 10715

10037

10037, 10668, 11037

11454, 10556, 10037

10037, 10714, 10715

10499

10698

10037

10556, 10037, 10714,

10195, 11037, 10208,

11666, 11667

10650

11755

12493

10698

10556, 10037

Mivar

Moree

Morgan's

Moserbaer

MTC

MTlogic

Mudan

Multitec

Multitech

Myrica

Myryad

NAD

Television

Medion

Megatron

MEI

Memorex

Mercury

Mermaid

Metronic

Metz

MGA

Micromaxx

Microspot

Mikomi

Minato

Minerva

Ministry Of Sound

Minoka

Mirai

Mitsubishi

10556, 10037, 10714,

10668, 11037, 10698,

10512, 11248, 11585,

11667, 12001, 12719

10178

11037

10150, 10178, 11037

10037

10037

10625

10037, 10668, 10195,

11037, 11533

10150, 10178

10037, 10714, 10668,

11037, 11324, 12001

11614

11037, 11585

10037

10195, 11248

11667

10037

11666

10150, 11250, 10178,

10556, 10037, 11037,

10512, 11171

10609

10037

10037

11585

10512

10714

10208

10037, 10668, 11037

10037

11666

10556

10178, 10037

Normerel

Nortek

Novatronic

Novita

Nu-Tec

O.K.Line

Oceanic

Odys

Okano

OKI

Olevia

Omni

Onei

Onida

Onimax

Television

Naiko

Nakimura

National

NEC

Neckermann

NEI

NEO

Netsat

NetTV

Neufunk

New Tech

Newave

Nikkai

Nikkei

Nikko

Nokia

Norcent

Nordmende

13

10037

10037

10508, 10208

10178, 10653, 10508,

10499

10556, 10037

10037, 11037

11324

10037

11755

10556, 10037, 10714

10556, 10037

10178

10037

10714

10178

10208

11365

10037, 10714, 10560,

10195, 11585, 11667,

12001

10037

10668

10037

11585

10698

11037, 11324

10208

12719

10037

11585, 11667

11610, 12124

10698

11667

10653

10714

Panavision

Panda

Pansonic

Penney

Perdio

Perfekt

Petters

Philco

Philips

Television

Onix

Onkyo

Onn

Onyx

Opera

Optimus

Orbit

Orion

Orline

Ormond

Osaki

Osio

Osume

Otto Versand

Pacific

Palladium

Palsonic

Panama

Panasonic

Phocus

Remote Control Codes

10698

11807, 13100, 13500

11667, 11709

11709

10037, 10714

10650

10037

10556, 10037, 10714,

11037, 12001

10037

10668, 11037

10556, 10037

10037

10037

10556, 10037, 10195,

10512

10556, 10714, 11037,

11324

10556, 10037, 10714

10037, 10698

10037

11480, 10037, 10650,

10508, 10208, 11636,

12170

10037

10698, 10508, 10208

11636

10178

10037

10037

10037

10178, 10171, 10037,

11394

10178, 10171, 11454,

10556, 10037, 10512,

10605, 10690, 11394,

11506, 11867, 12372

10714, 11652

Protech

Proton

ProVision

Pvision

Pye

Qingdao

Quasar

Quelle

R-Line

Radiola

Radiomarelli

RadioShack

Radiotone

RCA

Television

Phoenix

Phonola

Pioneer

Plantron

Playsonic

Powerpoint

Prinston

Profitronic

Proline

Prosonic

Realistic

Recor

Rectiligne

Redstar

10037

10556, 10037

10037, 10698, 10512,

11457, 11636, 12171

10037

10037, 10714, 10715,

11652

10037, 10698

11037, 10715

10037

10037, 10625, 10634,

11037

10037, 10714, 10668,

11324, 11585, 11667,

11709, 12001

10037, 10668, 11037

10178

10556, 10037, 10714,

11324

12001

10556, 10037

10208

10650

10037, 10668, 10195,

11037, 10512

10037

10556, 10037

10037

10178, 10037

10037, 10668, 11037

10178, 11454, 10625,

10560, 10618, 11781,

12247, 12403, 12429,

12434, 12746, 12932

10178

10037

10037

10037

Sansui

Sanyo

Television

Reflex

Relisys

Remotec

Reoc

Revox

RFT

Roadstar

Rolson

Rowa

Saba

Sagem

Saivod

Salora

Sampo

Samsung

SBR

Schaub Lorenz

Schneider

Schoentech

Scotch

Scott

Sears

Seaway

Seelver

SEG

SEI

10037, 10668, 11037

11585

10171, 10037

10714

10037

10037

10037, 10714, 10668,

11037, 10715

12001, 12098

10037, 10698

10625, 10714, 10560

10618

10037, 10668, 11037

10208, 12001

10178, 10171, 10650,

11755

10178, 10556, 10037,

10618, 10650, 10208,

12051

10171, 10037, 10714,

11248, 12001

11037, 10508, 10208,

11142, 11365, 11585,

11667, 11974

10556, 10037

10714, 11324, 11363,

11667, 12001

10556, 10037, 10714,

10668, 11037

11037

10178

10178

10178, 10171

10634

11037

10037, 10668, 11037,

12719

10037

Television

Sei-Sinudyne

Serie Dorada

Shanghai

Sharp

Shintoshi

Shivaki

Siam

Siemens

Siera

Silva

Silva Schneider

Silver

SilverCrest

Sinudyne

SKY

Skyworth

Sliding

SLX

Solavox

Soniko

Soniq

Sonitron

Sonneclair

Sonoko

Sonolor

Sontec

Sony

Soundesign

Soundwave

Sowa

Squareview

Standard

Starlite

Strato

14

10037

10178

10208

10650, 10818, 11165,

11423, 11659

10037

10178, 10037

10037

10037, 10195

10556, 10037

10037

10037

10715

11037

10037

10037, 11614, 11775

10037, 10698

11324

10668

10037

10037

12493

10208

10037

10037

10208

10037

10810, 11505, 11167,

11651, 11825

10178

10037, 11037, 10715

10178

10171

10037, 11037, 11709

10037

10037

Tec

Tech Line

Technica

Technics

Technika

TechniSat

Technisson

Techno

Television

SunBriteTV

Sungoo

Sunny

Sunstar

Sunstech

Sunwood

Supersonic

SuperTech

Supra

Svasa

Swisstec

Sylvania

Symphonic

Synco

Syntax

Sysline

Tacico

Talent

Tashiko

Tatung

TCL

TCM

Teac

Remote Control Codes

11610

11248

10037

10037

12001

10037

10208

10556, 10037

10178

10208

11614, 11775

10171, 11394, 11864,

11886

10171, 11394

10178, 11755

11610

10037

10178

10178

10650

10037, 11248, 11324

10698, 12403, 12429,

12434, 13183

10714, 12001

10178, 10171, 10037,

10714, 10668, 11037,

10698, 10512, 11248,

11363, 11709, 11755

10037

10037, 10668

11037

10556, 10650

11667

10556

10714, 11652

11585

Telefusion

Telegazi

Telemeister

Telesonic

Telestar

Teletech

Teleview

Tennessee

Tensai

Tesla

Tevion

Television

Technosonic

Techvision

Techwood

Tecnimagen

Teco

Tedelex

Teknika

TELE System

Telecor

Telefunken

Thomson

Thorn

Thorn-Ferguson

TMK

Tokai

Tokaido

Topline

Toshiba

10556, 10625, 10499,

11324

11709

11037, 11667

10556

10178, 10653

10208, 11709

10150

11585

10037

10037, 10625, 10714,

10560, 10698, 11585,

11667

10037

10037

10037

10037

10556, 10037

10037, 10668, 11037

10037

10037

10037, 11037, 10715

10556, 10037, 10714,

11037, 11652

10556, 10037, 10714,

10668, 11037, 11248,

11585, 11667

10037, 10625, 10560

10037, 10499, 10512

10499

10178

10037, 10668, 11037

11037

10668, 11037

10195, 11037, 10618,

10650, 10508, 11169,

11508, 11524, 11652,

12203

Television

Toyoda

TRANS-continents

Transonic

Vexa

Victor

Videocon

VideoSystem

Vidtech

Viewsonic

Vision

Vistron

Vivax

Vizio

Vortec

Voxson

Triad

Trio

Triumph

TVTEXT 95

Uher

Ultravox

UMC

Unic Line

Uniden

United

Unitek

Universal

Universum

Univox

V7 Videoseven

Vestel

11709

10556, 10037, 10668,

11037

10037, 10698, 10512,

11363

10556

11248

10556, 10037

10556

10037

10037

11614, 11775

10037

12122

10556, 10037, 10714,

11037, 10715, 11652

11709

10037, 10714

10037, 10668, 10195,

11037, 10618, 10512

10037

11666, 11755

10037, 10668, 11037,

11585, 11667

10037

10650, 10653, 11428

10037, 10508

10037

10178

11365, 11564, 11755,

12049

10037

11363

11709

11758, 12209

10037

10178, 10037

Television

VU

Xiahua

XLogic

Xrypton

Yamaha

Yamishi

Yokan

Yoko

YU-MA-TU

Zenith

Zepto

Zonda

11365, 12098

Walker

Waltham

Wansa

Wards

Watson

Wega

Welltech

Weltstar

Westinghouse

Wharfedale

11667

10037, 10668, 11037

12098

10178

10037, 10714, 10668,

11037

10037

10714, 11652

11037

11755

10556, 10037, 11324,

11667

White Westinghouse 10037

Wilson 10556

Windsor

Windy Sam

10668, 11037

10556

Wintel

World-of-Vision

Wyse

Xenius

10714

12001

11365

10634

10698

10698

10037

10650, 11576

10037

10037

10037

10037

10178, 10037, 11365,

11423, 12358

11585

10698

VCR

DirecTV

Go Video

20739

20614

15

Remote Control Codes

VCR

Humax

Panasonic

Philips

ReplayTV

Sonic Blue

Sony

TiVo

20739

20614, 20616

20739

20614, 20616

20614, 20616

20636

20636, 20739

PVR

DirecTV

Go Video

Humax

Panasonic

Philips

ReplayTV

Sonic Blue

Sony

TiVo

20739

20614

20739

20614, 20616

20739

20614, 20616

20614, 20616

20636

20636, 20739

TV/VCR Combination

Amstrad

Ferguson

Fidelity

GoldStar

Grundig

LG

Mitsubishi

Philips

10171

10625

10171

10037

10556, 10037, 10195

10178

10556

10556, 10037

Radiola

Saba

Sanyo

Schneider

Sharp

Siemens

Sony

Teac

10556

10625

11974

10556, 10037

10818

10037

11505

10178, 10171

TV/VCR Combination

Technics 10556

Thomson 10625

DVD

3D LAB

Accurian

Acoustic Solutions

AEG

AFK

Aiwa

Akai

Alba

Ambiance

Amstrad

30539

30675

30713

30675

31152

30533

30675

30539, 30713

33052

30713

Anthem

Aristona

ASDA

Audix

Autovox

Awa

Basic Line

Bel Canto Design

Black Diamond

32820

30539, 30646

32213

30713

30713

32587

30713

31571

30713

Blue Parade

Blue Sky

Brandt

Bush

30571

30713

30503

30713

C-Tech 31152

California Audio Labs 30490

Cambridge Audio

Centrum

Changhong

32808

30675, 30713

30627

Cinetec

Clatronic

Clayton

Crown

30713

30675

30713

30713

DVD

Dantax

Denon

Firstline

Foehn & Hirsch

Funai

GE

GFM

Global Sphere

Go Video

GoldStar

Goodmans

GPX

Grandin

Grundig

H & B

Haaz

Hanseatic

Dick Smith

Electronics

Digihome

DigiLogic

Digix Media

Disney

DSE

Dual

Durabrand

Dynex

Dyon eBench

Elfunk

Elite

Emerson

EuroLine

Ferguson

Finlux

30539, 30713

30490, 30634, 31634,

32258, 32748

31152

30713

33052

30675

30522

30675

31152

30741

30741

30713, 31152

30741

30713

30539, 30713

30713

31152

30741

30713

30713

31394

30675

30675, 31152

30713

30675, 30713

32596

33052

31152

30713

31152

30675, 32213

30675

30713

30741

DVD

Harman/Kardon

Henss

Hitachi

Hoeher

HotMedia

Humax

Inno Hit

Insignia

Integra

Irradio

JVC

Kendo

Kennex

Kenwood

Lenco

Lexicon

LG

Limit

Lodos

Loewe

Logik

Lumatron

Lunatron

Luxman

Luxor

Magnavox

Manhattan

Marantz

Mark

Matsui

30582, 31229, 33228

30713

30573, 30713, 31664

30713

31152

30646

30713

30741, 30675, 32428,

32596

30503, 30571, 30627,

31612, 31634, 32147

30646

30503, 30539, 30623,

30867, 31597, 31602,

32855

30713

30713

30490, 30534

30713, 33052

32545

30741, 31602

33052

30713

30539, 30741, 32474,

32783

30713

30741, 30713

30741

30573

30713

30503, 30539, 30646,

30675, 30713, 31354

30713

30539, 32414, 32432,

33444

30713

30713

Remote Control Codes

DVD

Maxim

MDS

Medion

Memorex

Metz

Micromedia

Micromega

Microsoft

Minax

Mitsubishi

Momitsu

NAD

NEC

Onkyo

Oppo

Orion

Ormond

Pacific

Palladium

Panasonic

Pelican Accessories

Philco

Philips

Pioneer

Polk Audio

Presidian

ProAudio

Proscan

Proson

Pye

30713

30713

30630, 30741

32213

30571, 30713

30503, 30539

30539

30522, 32083

30713

30713

33052

30741

30741, 31602

30503, 30627, 31612,

32147, 30571, 31634

30575, 32545

30713

30713

30713

30713

30503, 30490, 31579,

31641, 32523, 32710,

32859

30533

30675

30503, 30539, 30646,

30675, 30713, 31340,

31354, 32056, 32084,

32434, 32689

30571, 30142, 30631,

31571, 32442, 32860

30539

30675

31394

30522

30713

30539, 30646

16

DVD

Radionette

Radiotone

RCA

REC

Red

Redstar

Roadstar

Rotel

Salora

Samsung

Sanyo

Schneider

Schoentech

Scott

SEG

Semp

Sharp

Sherwood

Shinsonic

Silva Schneider

SilverCrest

Skantic

SM Electronic

Smart

Sony

Soundwave

Star Clusters

Strato

Strong

Supervision

30741

30713

30522, 30571, 32213,

32587

30490

32213

31394

30713

30623

30741

30490, 30573, 30199,

30820, 31635, 32069,

32329, 32489, 33195

30713

30539, 30646, 30713

30713

31394

30713

30503

30630, 30675, 30713,

32250, 32474, 32652,

32869

30741, 33052

30533

30741

31152

30539, 30713

31152

30713

30533, 30864, 31033,

31070, 31431, 31516,

31633, 32180

30713

31152

31152

30713

31152

DVD

Sylvania

Symphonic

Tamashi

Tandberg

Targa

Tchibo

TCL

TCM

Teac

Technica

Technics

Techwood

Teletech

Theta Digital

Thomson

Toshiba

Transonic

TVE

United

Universum

Urban Concepts

Vestel

Victor

Vizio

Vtrek

Waltham

Wellington

Weltstar

Wharfedale

Windsor

Windy Sam

Xbox

XLogic

30630, 30675

30675

31394

30713

30741

30741

32587

30741

30571, 30741, 30675,

31394

30713

30490

30713

30713

30571

30522

30503, 31639, 32277,

32551, 32705, 33157

31394

30713

30675, 30713, 31152

30741, 30713

30503

30713

31597

32563

32587

30713

30713

30713

30713

30713

30573

30522, 32083

31152

DVD

Yamaha

JVC

Lenco

Lexicon

LG

Limit

Loewe

Magnavox

Marantz

Momitsu

Onkyo

Zenith

Blu-ray Disc

Ambiance

Anthem

Cambridge Audio

Denon

Dyon

Foehn & Hirsch

Funai

Harman/Kardon

Insignia

Integra

Oppo

Panasonic

Philips

Pioneer

Samsung

Sharp

Sherwood

30490, 30539, 30646,

30817, 31354, 32298,

32299

30503, 30741

33052

32820

32808

32258, 32748

33052

33052

30675

33228

30675, 32428, 32596

32147, 32900, 32910,

33100, 33101, 33500,

33501

32855

33052

32545

30741, 31602

33052

32474, 32783

30675

32414, 32432, 33444

33052

32147, 32900, 32910,

33100, 33101, 33500,

33501

32545

31641, 32523, 32859

32084, 32434, 32689

30142, 32442

30199, 33195

32250, 32474, 32652

33052

Philips

Pioneer

Pye

RCA

Samsung

Schneider

Sharp

Sony

Sylvania

Targa

Toshiba

Blu-ray Disc

Sony

Sylvania

Toshiba

Vizio

Yamaha

DVD-R

Accurian

Aristona

Denon

Emerson

Funai

Go Video

GPX

Hitachi

Humax

Irradio

JVC

LG

Loewe

Magnavox

Medion

Panasonic

Remote Control Codes

31516, 32180

30675

32551, 32705, 33157

32563

32298, 32299

30675

30646

30490

30675

30675

30741

30741

31664

30646

30646

31597

30741

30741

30646, 30675

30741

30490, 31579, 32523,

32710, 32859

30646, 31340

30631, 32860

30646

30522

30490, 31635

30646

30630, 30675, 32869

31033, 31070, 31431,

31516, 31633, 32180

30675

30741

31639, 32277, 32551

17

DVD-R

Victor

Yamaha

Zenith

HD-DVD

Integra

LG

Microsoft

Onkyo

Xbox

31597

30646

30741

32901, 33104 33504

30741

32083

32901, 33104 33504

32083

Ferguson

Goodmans

Grandin

Grundig

H & B

Hanseatic

Hitachi

Insignia

JVC

LG

Logik

Luxor

TV/DVD Combination

Akai

Black Diamond

Blue Sky

Bush

Centrum

Crown

DMTech

11675

11037, 30713

11037, 30713

11037, 10698, 12719,

30713

11037, 30713

11037, 30713

12001

Dual

Dynex

Elfunk

Emerson

11037, 30713

12049

11037, 30713

11394, 11864, 11886,

30675

11037, 30713

11037, 30713

30713

30539

12001

12001

11037, 11667, 30713

12049

12271

11423

11037, 30713

11037, 30713

Teac

Technica

Telefunken

Teletech

Thomson

Toshiba

United

Universum

Vestel

Viewsonic

Weltstar

TV/DVD Combination

Magnavox 12372

Matsui

Medion

Nordmende

Odys

Panasonic

Philips

Powerpoint

Prosonic

Pvision

RCA

11037, 30713

12719

12001

12719

12170

11454, 10556, 11394,

30539

10698

12001

12001

12746, 12932

Schaub Lorenz

SEG

Sharp

Soniq

Sunstech

Sylvania

12001

11037, 12719, 30713

10818

12493

12001

10171, 11394, 11864,

11886, 30630, 30675

10698

11037, 30713

10698

11037, 30713

10625

11524

11037, 30713

30713

11037

12049

11037, 30713

18

Remote Control Codes

Memo

Remote Control Codes

19

SN 29401094

(C) Copyright 2012 ONKYO SOUND & VISION CORPORATION Japan. All rights reserved.

Y1112-1

* 2 9 4 0 1 0 9 4 *

advertisement

Related manuals

advertisement

Table of contents