OPERATING YOUR TIMER
For normal operation the setting slider must be in the
RUN PROGRAMME position.
A red indicator lamp shows when the appliance is
switched ON.
An OPERATING SLIDER is provided to select how
the appliance is controlled.
The OPERATING SLIDER has four positions;
OFF
The appliance will remain OFF.
AUTO
The appliance will be switched ON and OFF
automatically according to the programme.
ONCE
The appliance will come ON at the first
programmed ON time and go OFF at the last
programmed OFF time.
CONT.
The appliance will remain ON continuously.
OVERRIDE
The OVERRIDE button switches the appliance ON
or OFF without altering the programme.
When the indicator lamp is ON, pressing the
OVERRIDE button switches the appliance OFF until
the next programmed ON time.
When the indicator lamp is OFF, pressing the
OVERRIDE button switches the appliance ON until
the next programmed OFF time.
EXTRA HOUR
The EXTRA HOUR button switches the appliance
ON for up to 3 extra hours without altering the
programme. Pressing the button once will give one
extra hour, and the message +1 HR shows on the
display to confirm the button has been pressed.
When the red indicator lamp is OFF, pressing the
EXTRA HOUR button switches the appliance ON
for just one hour.
When the red indicator lamp is ON, pressing the
EXTRA HOUR button extends the programmed
ON period by one hour.
Further presses of the EXTRA HOUR button wil
increase the extra hour period by one hour for each
button press, up to a maximum of 3 hours. The
display will change to show the number of extra
hours, for example +2 HR or +3 HR.
To cancel the extra hours, keep pressing the
EXTRA HOUR button until the + (1,2 or 3) HR
message disappears from the display.
RESET
To reset the timer back to the original built-in
programme press the RESET button with the tip
of a pen or pencil.
POWER FAILURE
Your timer has a built-in battery to ensure correct
operation after a mains supply power cut. No
action should be necessary after a power cut of
up to 4 days. Longer power cuts may require you
to reprogramme.
Honeywell
ST6 100A T imer
.
[
Honeywell
о. Г
050020 am
ON OFF
OVERRIDE EXTRA HOUR
° GC
42009084-001 R2
INTRODUCTION
The ST6100A timer can be used to control any
appliance requiring to be switched ON and OFF at
fixed times during the day
FEATURES
« 24 hour programme.
* Two ON/OFF switching times each day.
* Built-in programme with typical ON/OFF times.
* Programme override button,
* Extra hour button.
Built-in battery to prevent loss of programme during
power cuts,
* 12 hour am/pm or 24 hour clock format.
The STE100A may be used with other Honeywell
controls to form part of a total control system.
12 HOUR AM/PM or 24 HOUR CLOCK DISPLAY
Your timer can operate on 12 hour am/pm or 24 hour
clock formats. To change the format, ensure the
setting slider is in the RUN PROGRAMME position
ther press the + and = buttons together for about 5
seconds. All the displayed times will automatically
be changed to the new format.
Repeating this procedure will change the clock display
back to the original format.
IF DISPLAY REMAINS BLANK AFTER SWITCH ON — PRESS RESET
SETTING YOUR TIMER
SETTING THE CORRECT TIME
To set the correct time open the flap on the front of the
timer.
STEP 1
Move the setting slider (7 —
to the SET TIME | Cr |
| y fa Í / / АМ
I
position. The time on
the display will now
be flashing to indicate |. | J
it can be changed. [on ur] on om]
STEP 2
To change the time, press the + or = buttons until the
correct time is displayed.
Each press of the button will change the time by one
minute, Holding the button down for more than a few
seconds will change the time slowly at first, then
quickly.
STEP 3
Moving the setting slider to the next position completes
setting the time.
SETTING THE PROGRAMME
The programme has two ON/OFF switching times
which are repeated daily. Each time can be set
between 3.00am and 2.50am (on the next day) to
allow you to programme the appliance to stay ON
after midnight, if required.
STEP 4
Move the setting slider to the SET PROGRAMME
position. The first ON time will be flashing.
STEP 5
Use the + and = buttons to set the first ON time. Each
press of the button will change the time by 10 minutes.
STEP 6
Press the NEXT ON/OFF button once to display the
first OFF time. Set this time using the + and = buttons.
STEP 7
By pressing the NEXT ON/OFF and + or — buttons
the remaining ON/OFF times can be set.
‘NOTE-
1 When pressing the + button, the next ON or OFF
marker may start to flash. If this happens the next
programme time will have been changed. Press
the NEXT ON/OFF button to check and adjust this
programme time if necessary.
2 When pressing the = button, the previous ON or
OFF marker may start to flash. If this happens the
previous programme time will have been changed.
Follow the procedure in “REVIEWING
PROGRAMME TIMES” to check and adjust this
time, if necessary.
Moving the setting slider to the next position completes
the setting of the programme.
REVIEWING PROGRAMME TIMES
To review your programme move the setting slider to
the SET PROGRAMME position.
To review fhe programme times press the NEXT ON/
OFF button repeatedly. Any of these times can be
adjusted by using the + and = buttons.
LCD + AND -
DISPLAY BUTTONS RESET
Honeywell
A NEXT ON/OFF
ON/OFF | Y BUTTON
MARKER E x NEXT ON/OFF
| mo
> _
on ono
SET PROGRAMME —
A SETTING
AEF A uTO AER CONT AUN PROGRAMME L—" SLIDER
IL
OVERRIDE EXTHA HOUR OPERATING
INDICATOR BUTTON BUTTON SLIDER
IF DISPLAY REMAINS BLANK AFTER SWITCH ON - PRESS RESET
BUILT-IN PROGRAMME
AM PM AM
S DDH о FF PH © SS
DF FFF SATS iD oS FUSE FS EN
6.30 1.30 | 4.30 10.
PERSONAL PROGRAMME
AM PM AM
о & FP PH OS HESS ©
HRS SNS NP LS
Dv >
STE
SS SF Fe oe
a ‘ a: TA
">
