Stinger SPXRGB5 RGB Light Strips for In-Vehicle Accent Lighting Owner's Manual

Add to My manuals
2 Pages

advertisement

Stinger SPXRGB5 RGB Light Strips for In-Vehicle Accent Lighting Owner's Manual | Manualzz

SPXRGB5

MARINE GRADE UNIVERSAL RGB LED STRIP - 5 METERS

The SPXRGB5 light strip can be cut every 2 inches and installed with 3M peel-and-stick adhesive backing. The light strip operates within an 11-14.8 VDC range and can be used stand alone for basic solid colors or with the Stinger

SPXRGBC RGB Controller for multiple color-changing options and lighting effects.

Basic Wiring

1. Cut light strip to length at solder pads indicated by the scissor icon and line. Fig A

2. Remove rubber coating and adhesive from the front and back of the solder pads.

3. If using a RGB controller, solder the 4 control wires (FIG.B).

For a solid color, refer to to the table below and solder appropriate wires.

FIG. A

SPECIFICATIONS

• 5 Meters / 16.4 Feet

• 60 5050 LEDs per meter

• Voltage: 11-14.8 VDC,

• Current Draw: 1.2A per meter

CUT LINE

12V

G

R

B

12V

G

R

B

LED COLOR WIRE CONNECTIONS

RED

+12V to 12V Positive

R to Ground

GREEN

+12V to 12V Positive

G to Ground

BLUE

YELLOW

PURPLE

AQUA

WHITE

+12V to 12V Positive

B to Ground

+12V to 12V Positive

R and G to Ground

+12V to 12V Positive

R and B to Ground

+12V to 12V Positive

B and G to Ground

+12V to 12V Positive

R, G and B to Ground

FIG. B

G

R

B

12V +

G

R

B

GROUND

Example:

Connecting LED strip +12V to Power and connecting

R and B to Ground will illuminate Purple.

SPXRGB5

MARINE GRADE UNIVERSAL RGB LED STRIP - 5 METERS

4. When soldering, tin both the wire and the LED solder pad for best results.

After wire connections are made, insulate with heat shrink. (FIG. C)

FIG. C

G

R

B

Heat Shrink

5. If wiring direct, without a controller, you must fuse the +12V power source with a fuse. 3 to 5 amp fuse recomended.

OPTIONAL

ACCESSORIES

SPXRGBC

Optional SPXRGBC RGB Controller

SPXRGB5

3 AMP

FUSE

Black - Ground

Red - Battery (12V+)

Blue - Remote In (12V+)

Optional SPXRGBMF Solder Connectors

LIMITED WARRANTY:

Stinger warrants this product to be free of defects in materials and workmanship for a period of one (1) years from the original date of purchase. This warranty is not transferable and applies only to the original purchaser from an authorized Stinger dealer in the United States of America only. Should service be necessary under this warranty for any reason due to manufacturing defect or malfunction, Stinger will (at its discretion), repair or replace the defective product with new or remanufactured product at no charge. Damage caused by the following is not covered under warranty: accident, misuse, abuse, product modification or neglect, failure to follow installation instructions, unauthorized repair attempts, misrepresentations by the seller. This warranty does not cover incidental or consequential damages and does not cover the cost of removing or reinstalling the unit(s). Cosmetic damage due to accident or normal wear and tear is not covered under warranty.

INTERNATIONAL WARRANTIES:

Products purchased outside the United States of America are covered only by that country’s

Authorized Stinger reseller and not by Stinger. Consumers needing service or warranty information for these products must contact that country’s reseller for information.

TECHNICAL SUPPORT:

727-592-5991

Mon-Fri 9AM-8PM EST

Sat 9AM-7PM EST [email protected]

Stinger is a Power Brand of AAMP Global

15500 Lightwave, Clearwater, Florida 33760

P: 888-228-5560 [email protected]

www.stingerelectronics.com

© 2019 AAMP Global

advertisement

Related manuals

Download PDF

advertisement