CNB DI1310NVF/DI1310PVF Owner's Manual


Add to my manuals
1 Pages

advertisement

CNB DI1310NVF/DI1310PVF Owner's Manual | Manualzz
 This manual explains the installation and operating method \ ее / -
INSTALLATION Va for the color dome camera Bors instalation make Sure ee N CAMERA SET-UP
ou are familiar with this product's special features an ; ; :
proper operating technique. р о @ © The 3D bracket (Pan, Tilt and Horizontal) Vari-focal Lens Type
allows the camera to be manually as well
as moved horizontally and vertically.
NAME AND FUNCTION
/ 7 s
© Function Selection Switch:
*FL(Flickerless) ON/OFF
* AGC(Auto Gain Control) ON/OFF
*BLC(Back Light Compensation)
ON/OFF
O Service Monitor Connecter:
Use service monitor connector
to set camera angle & focus
when installing.
= Using the guide pattern as a template, cut a round opening it the
wall or ceiling.
€) DC Level Adjustment V.R
01 |J502
J504
MP =,
uen
Za |:
-
O
Drill three holes according to the guide pattern then insert anchors
into the drilled holes.
iL
Fixed Lens Type
Vari-focal Lens Type
Fix the camera to a ceiling using three screws,
= Adjust desired focus and scene by turning and moving the 3-axis
camera bracket by hand.
Fix the dome cover on the base with decorative ring.
SWITCH VIDEO
@ CAUTION : In case of AGC off,
the switching of D&N doesn't work.
Because the D&N switching function
DOME BASE is related in AGC level.
MOUNTING
|- SCREW fÆ If you have trouble operating your camera, refer to
TROUBLE SHOOTING the following. If the guidelines do not enable you to solve
= Camera Lay-out the problem, contact an authorized technician.
DECORATIVE
RING
NOTE — © Tilt rotation: Adjusting the vertical angle. €) Focus handle: Focus (Far or Near) = The image does not appear = Check the power source for the monitor and camera
‹ . E . g ppe Ч
> @ Pan rotation: Adjusting the horizontal angle. © Zoom handle: Zoom (Tele or Wide) on the screen. and assure that the voltage and polarity are properly
. €) Horizontal rotation: Adjusting the horizontal connected and being supplied correctly.
Insert coin to the side hole and re- osition of the screen
move the dome cover by twist coin. DOME COVER Р -
N
= The image on the = Check if the lens is stained.
/ CONNECTION screen is dim If dirty, clean the lens with a soft, clean cloth.
=
= Adjust the Back Focus of the lens again.
Video/Yellow o ПЕН Video/Yellow
V tput P NARA ;
© ideo Outpu ower(s) Video Output 24V AC/12V DC = The camera does not work = Check if you have connected the camera to a proper
properly, the surface of the power source and if there is no problem with the
camera case is hot, and power, turn the unit off immediately and seek assis
@ @ Power/Green a black line appears on —tance from our After Service department.
Power/Red GND GND 24V AC/GND the screen.
No. Function Terminal Color (E © No. Function Terminal Color
#1 Video Output Yellow #1 Video Output Yellow = The screen blinks a lot. = Check if de, Tamora is pointed toward the sun or
#2 Power Input Red 12V DC Power Type #2 Power Input Green 12V DC / 24V AC Power Type — Adjust the angle or location of the camera if 160 much
light is comming into the screen.
< J
— || 1 1 1111111111 —
5... 11 ro EEE
— N
EB Horizontal Rotation Tilt Rotation Pan Rotation
||
Ш 119 one
= т In-Ceiling
Ш
7 Mount
F :
3-Axis bracket makes adjustment easy.
3-AXIS CAMERA CONSTRUTION /
nll
r ees H—
SPECIFICATIONS / ies N INN
... *°° ини И Del zi ppt are
' subject to change without notice.
OWNER'S MANUAL „и 1 Model NTSC PAL ПЕЛИ : ы
Co Signal System NTSC : 525 Lines PAL : 625 Lines NE
DOME CAMERA SERVICE MONITOR CABLE MOUNTING SCREW GUIDE PATTERN Scanning System 2: 1 Interlace an
Scanning Frequency(H) 15.734kHz 15.625kHz wy
/ Scanning Frequency(V) 59.94Hz 50Hz Y
COMPOSITION PRECAUTION Image Sensor 1/3 inch SONY Super HAD CCD
A Total/Effective Pixels No. 410K/380K 470K/440K le
Resolution 550 TV Lines “A
= Do not install the camera in extreme temperature conditions. Min, Illumination 0.3 Lux / 0.1 Lux (D/N) ч
Do use the camera under conditions where temperatures are within
-10°C to 40°C. Be especially careful with ventilation under high temperatures.
= Do not install or use the camera in an environment where the
S/N Ratio
More than 48dB (AGC off)
Video Output Levels
1.0 Vp—p (75 Ohms, composite)
humidity is high. Sync. System Internal
It can cause the image quality to be poor. White Balance Auto (AWB) |
= Do not disassemble the camera. AGC On / Off V y
There are no user-serviceable parts inside it. BLC On / Off + 7
= Do not drop the camera or subject them to physical shocks. Flickerless On / Off
It can cause malfunctions to occur. Lens Fixed Lens: 3.8mm
= Do not expose the camera to rain or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that corrode the electronic components.
= Note
If the camera is exposed to spotlight or object reflecting the strong
light, smear or blooming may occur. Please check the power whether
it satisfies the normal specification before connecting the camera.
—— OEA EEE
Me | TTM
Vari—focal Lens: 4mm ~ 9mm, 2.9mm ~ 10mm (D/N)
Input/Output Connector
Power (Red/Green Jack), Video (Yellow Jack)
Power Consumption
(Option: 24V AC/12V DC)
12V DC (9V ~15V) / 3W (Max)
24V AC (20V < 28V) or 12V DC (10V -15V) / 5W (Max)
Dome Size (9)
100mm
Weight
Approx. 410g
a
In-Ceiling
(ВЕЛИ) Сатега
me | | Г
B/N: 3810-01214 (ver.070sc) NENNIR IRR EE EER ER ER ER IRN
y
E | | | || | |||
Jl

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

advertisement