CNB WCM-20VF/WCM-21VF Owner's Manual

Add to my manuals
36 Pages

advertisement

CNB WCM-20VF/WCM-21VF Owner's Manual | Manualzz
 INTELLIGENTEIR:
БООТ У!
UWNER S MANUAL
* Intelligent IR Technology
* 1/3" High Sensitivity CCD
* Ultra High Resolution [E00TVL)
* Selectable, Day & Night
* Motion Detection
* Privacy Zone
eso
COLOR CCD DSP DIGITAL DIGITAL COLOR
NL
WEATHERPROOF IR CAMERA Г, 2
O USER INFORMATION
7 RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIHED SERVICE
PERSONNEL.
ZA
/N
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of un-insulated “dangerous voltage” within the products enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral tnangle is intended to alert the user to the presence
of Important operating and maintenance-(servicing) instructions in the literature accompanying
the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
“WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.”
e USER INFORMATION
INFORMATION
This equipment has been tested and found to comply with limits for a Class Á digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
1s operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, If not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area Is likely to cause harmful interference in which case the user
will be required to correct the interference at their own expense.
WARNING
The manufacturer could void the user's authority to operate the equipment.
CAUTION
To prevent electric shock and risk of fire hazards:
* Do not use power sources except for that specified.
* Do not expose this appliance to rain or moisture.
WEATHERPROOF IR CAMERA Ч m ) \
O CONTENTS
Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully
to obtain the best result and keep this manual for future reference.
1. SAFETY INSTRUCTIONS --------------—-- 5 7. OPERATING CAMERA —----——-——--—----—- 44
2. PRECAUTIONS -----------------—-<--<"-"""e 6 8. SPECIFICATION ----—--—-----—-—-————— 30
3. FEATURES neo 7
4. NAME AND FUNCTIONS --—-----------—--— 8 9. TROUBLESHOOTING -------—--—-—-——- 32
5. CONNECTIONS -—--—-—-—-—-————— 9
6. COMPOSITION -—-———-—-—-———— 10
N\
(a Y WEATHERPROOF IR CAMERA
© 1. SAFETY INSTRUCTIONS
Read Instructions
a
Read all of the safety and operating instructions
betore using the product.
Installation
+
Do not place this product on an unstable cart,
stand, or table. The product may fall causing
serious Injury to a child or adult, and damage
to the product.
Use only with a cart or stand recommended
by the manutacturer, or sold with the product.
Mounting should follow the manufacturers
Instructions, and should use a mounting accessony
recommended by manufacturer.
Retain Instructions,
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liqud cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Power source
This product should be operated only from
the type of power source indicated on the
marking label.
It you are not sure of the type of power supplied
to your home, consult your dealer or local
power company.
EZ
WEATHERPROOF IR CAMERA € 2
O 2. PRECAUTIONS
5 Do not install the camera in extreme temperature conditions.
Operate the camera under conditions where temperatures are within -10°C to 50°C.
Especially be careful for ventilation under high temperature.
9 Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
9 Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
o Do not disassemble the camera.
There are no user repairable parts inside.
2 Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
9 Never keep the camera face to strong light directly.
It can damage CGD.
strong electromagnetic field, irregularity such as noise on the monitor may appear.
6 © NOTE When this camera is installed near wireless communication devices that emits |
(~ Y WEATHERPROOF IR CAMERA
e 3. FEATURES
1. Intelligent IR Technology
"Intelligent IR" technology dramatically eliminates the white out effect and saturation on close objects,
producing a clear and recognizable image regardless of viewing condition or location of objects.
2. 1/3” High Sensitivity CCD
3. Min Illumination (F1.2, 30IRE, AGC Max)
- 0.05 LUX (COLOR)
- 0.005 LUX (ICR, B/W)
- 0.00 LUX (IR LED ON)
4. High performance menus for functions
- Ultra High Resolution (600TVL)
- SBLC (Super Back Light Compensation)
- DNR (Digital Noise Reduction)
- Privacy zone selectable.
- Motion detection selectable.
- MIRROR (HORIZON TAL)
- Fickerless On/Off.
WEATHERPROOF IR CAMERA
Vari-focal Lens Type
© IRLED
850nm / 30°(18EA)
Ó Focus Handle
Used to provide for accurate focusing
of object within the lens field of view.
©) Zoom Handle
Used to adjust zoom magnification by
turning.
sE."
BB (7 O MN NA
O 5. CONNECTIONS
Connecting to Monitor and Power
Video Output
9 For 12V DC Power Туре
- Connect the video-out jack to the video-in jack ot monitor.
- Connect the power adapter to the power input connecter.
- Use 12V DC power source. : GND
- Use the power rated at least 400mA (12VDC) = @® —®
Remark
Video Output 1.0 Мр.р
12V DC{10V~15V),
Max 4.8W /400mA
Power Input
WEATHERPROOF IR CAMERA 7 NN
® 6. COMPOSITION
(
O 7. OPERATING CAMERA
WEATHERPROOF IR CAMERA
ESC BRIGHTNESS 0-5
DC LEVEL 0-5
LENS 1160/11/50) 11 20(1/100), 1/250, 1/500 17700, 1/11, 10/1600, 11/2500
DC
SHUTTER 1/6K, 1/7E, 110K, 130K, 1/60K, 1/1 20K
IH MODE: 1/60{ 1/50)
ATW
RED 0-- 160
WHITE BAL MANLLAL BLUE 0160
PUSH
AGC ON LEVEL 0-20 (IR MODE:FIXED)
OFF
HED ENEE LEVEL LE N MIGDLE HIE
DAY / NIGHT COLOR
B/W BURST ON/OFF
SALC OFF, LOW, MIDDLE, HIGH
DNR OFF, LOW, MIDDLE, HIGH
SHARPNESS LEVEL 0-20
MIRROR OFF, ON
AREA 1-4
DISPLAY OFF ON
IMAGE ADJ SENSITIVITY 1-24
TOP 8126
MOTION BOTTOM 8-126
LEFT 4-191
RIGHT 4.191
INITIAL OFF, ON
RETURN +
WEATHERPROOF IR CAMERA * 2
AREA 1-4
DISPLAY OFF ON
COLOR WHITE, YELLOW, GREEN, BLUE, RED, BLACK, GRAY
TOP 4-63
PRIVACY BOTTOM 5-64
LEFT 18-205
RIGHT 19-206
IMAGE ADJ INITIAL OFF <1. ON
RETURN a
R-Y 0-20
COLOR GAIN NTE
INITIAL OFF «!, ON
RETURN +!
CAM ID 0-255
ID DISPLAY OFF, ON
OFF
er THRE ON UP/ DN, LE/ RI
rr LANGUAGE ENG
SYNC INT
BAUDRATE 2400, 4800, 9600, 57600
VERSION
INITIAL OFF + , ON
RETUBN pu
INITIAL OFF+ ON
HETURN +
"
Use the joystick to navigate between 5 ways.
E) DOWN : Move down
(ÿ UP : Move up
: ® LEFT : Move left
IS © RIGHT : Move right
O MENU(SET):
Press the joystick in its straight position.
& Sevice Monitor Connecter :
Use service monitor connector to set camera
angle & focus when installing.
(Image cannot be seen if monitor output and service
video output is used simultaneously.)
1 ON WEATHERPROOF IR CAMERA
MAIN MENU - GENERAL
Press MENU button to access the SETUP menu.
Select each sub-menu by using the 4.» A,Ÿ button.
Press the MENU(SET) button to select.
LENS DC +
WHITE BAL ATW
AGC ОМ +
DAY MIGHT IRED +
IMAGE ADJ a
GENERAL +
INITIAL ON
EXIT
EEE
AEREA EEE;
If the OSD MENU is changed then INITIAL will be OF.
(EXCEPT : LENS, CAM 1D, BAUDRATE)
4
WEATHERPROOF IR CAMERA Ч Mm )
+ MENU
LENS
i: LENS ESC «
Press the MENU button to access the SETUP menu. + > AR 3
‘1 DAY/NIGHT ЕО +!
‘i IMAGE ADJ +
:: GENERAL +
‘Ро INITIAL ON
EEE a 5
- Select LENS using the UP or DOWN button. You can change IN LIA II
between ESC and DC using the LEFT or RIGHT button.
Select ESC and Press MENU button to display LENS ESC.
1. BRIGHTNESS f— — 31
- Select BRIGHTNESS using the UP or DOWN button. + 2e
You can adjust between 0 ~ 5 using the LEFT or RIGHT button.
11 BRIGHTNESS | Ш |
TIlE E
"qa Ear
(@ Y WEATHERPROOF IR CAMERA
LENS DC +
Select DC and Press the MENU button to have 3 FLK OEE
LENS DC activated. 1 Ш ul
+ EXIT - MENU ¥
1 , DC LEVEL (Adjusts brightness of the image.) rat A
- Select DC LEVEL using the UP or DOWN button. You can adjust between O - 5 level using
the LEFT or RIGHT button.
2. FLK (FLICKERLESS)
- Select FLK using the UP or DOWN button. You can select between ON / OFF using the LEFT or
RIGHT button.
> OFF: You will be allowed to adjust the shutter speed.
3. SHUTTER (Adjusts the shutter speed of the lens.)
- IH LED Mode : 1/60(1/50)
- COLOR, B/W Mode :
select SHUTTER using the UP or DOWN button. You can adjust from 1/60(1/50), 1/120(1/100),
1/250, 1/500, 1/700, 1/1K, 1/1600, 1/2500, 1/5K, 1/7K, 1/10K, 1/30K, 1/60K, 1/120K(sec) level
using the LEFT or RIGHT button.
RZ
WEATHERPROOF IR CAMERA
WHITE BAL (White Balance)
Select WHITE BAL using the UP or DOWN button. You can select from ATW, MANUAL,
PUSH using the LEFT or RIGHT button.
1. ATW : Color temperature Is automatically adjusted to 2,000°K ~ 10,000°K
2. MANUAL : To set a certain color temperature with RED CONT, BLUE CONT
- Select MANUAL using the UP or DOWN button and press the MENU button to activate
WE MANUAL option.
зипиицииий Ng
RED +—d
BLUE | li
EXIT - MENU
WEEE EE EE EEE EEE EE EE EE EEE EE ET
1. RED: To Ari density of RED (0~160)
2. BLUE: To adjust density of BLUE ( 0- 160)
3. PUSH : lt the set color temperature does not meet your environment, press the MENU button
to adjust the color temperature to desired setting.
( a , WEATHERPROOF IR CAMERA
AGC (Automatic Gain Control )
Select AGC using the UP or DOWN button. You can select between OFF, ON using the
LEFT or RIGHT button.
AGC is fixed at a certain level in IR LED mode.
AGC level is selectable in COLOR, B/W mode.
1. ON : Select ON using the LEFT or RIGHT button and press the MENU button to activate
AGC option.
gM EE EE DUO ан ен нение
a EEE TA TS A A A A A N LA N LT, A A
E
a EEE EERE NE FIFE FFE FFF ENE FEIN FEF FEF REFEREE EET |
пн нае ва EEE EEE EE EEE EEE ESE ESE EEE EEE EERE EERE REE EEEEE
2. OFF : Disable the AGC
WEATHERPROOF IR CAMERA Г, NI
DAY / NIGHT
Select DAY / NIGHT using the UP or DOWN button.
You can select between IHED, COLOR, BW
using the LEFT or RIGHT button.
COLOR BURST
1. COLOR : for color mode only (DAY mode) + В! ON
2. B/W : for BLACK and WHITE mode only (NIGHT mode) + EXIT - MENU :
- Select BW using the LEFT or RIGHT button and press RR
the MENU button to activate COLOR BURST option. Itis possible to select ON/OFF using
the LEFT or RIGHT button.
=
BL WEATHERPROOF IR CAMERA
3. IRED : IR LED control mode 3 IR LED
WIDE : It controls the IR LED (full screen base),
MODE WIDE
Saturation may be expected depending ВЕ vEL _
on the installation environment. E:
SMART : It controls the IR LED (bright portion base), + EXIT_MENU E:
Satuation is not expected however, Image ARS RE BE SRSNSRERONOR NS RE RE NE BANS LEER OREN SR ORT NE RA NS BE RE ANY
may be darker.
WEATHERPROOF IR CAMERA Г, A )
IMAGE ADJ (Image Adjust)
Select IMAGE ADJ using the UP or DOWN button and press the MENU button to activate
the IMAGE ADJ mode.
IMAGE ADJ
SBLC OFF
DMR LOW
SHARPNESS +
MIRROR OFF
MOTION +
PRIVACY +
COLOR GAIN +
INITIAL ON
al
Тана Ба Ба Ба Ба Ба Ба 5 le le ol le ale ol OO OO le ol le el EE mA
1. SBLC (Super Back Light Ae lo o lighten a darker part of the image
- Select SBLC using the UP or DOWN button. You can select between OFF, LOW, MIDDLE,
HIGH using the LEFT or RIGHT button.
- SBLC turns to OFF automatically at night.
2. DNR (Digital Noise Reduction) : To reduce the image noise especially during the low ambient
lighting conditions.
- Select DNR using the UP or DOWN button. You can adjust between OFF, LOW, MIDDLE, HIGH
using the LEFT or RIGHT button.
Nu
WEATHERPROOF IR CAMERA
3. SHARPNESS : To adjust SHARPNESS of the image. ARRETE EE EEE EE EEE
- Select SHARPNESS using the UP or DOWN button. mi
- Select « and press the MEUN button to activate — 5
SHARPNESS option. |
- You can adjust the sharpness from 0-20 using the + +
LEFT or RIGHT button. een meh NN
4. MIRROR
- Select MIRROR using the UP or DOWN button.
You can select from ON/OFE using the LEFT or NT A
RIGHT button. + MOTION +
(1) ON : Horizontal image flip. + AREA 1
(2) OFF : default 1 SENSITIVIY
5. MOTION (Motion Detect) 4 BOTTOM 62
- Select MOTION using the UP or DOWN button and + AR a
press MENU button to activate MOTION DETECT option. + INITIAL OM
NU ji 21
WEATHERPROOF IR CAMERA
Fm mm pm mm ws mm от == = == т pm nem men A
1) AREA : lo specify MOTION DETECTION area |
- Select AREA using the UP or DOWN button. You can select from |: 1 2
area 1~4 position using the LEFT or RIGHT button.
2) DISPLAY : To display MOTION DETECTED area on the video ETT
- Select DISPLAY using the UP or DOWN button. You can select | 1
between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the MOTION DETECTED area on the screen
(2) OFF : disable eee)
3) SENSITIVITY : To setup the motion sensitivity
- select SENSITIVITY using the UP or DOWN button. You can adjust the motion sensitivity of
a movement from 1~24 using the LEFT or RIGHT button.
(1) 1: most sensitive (highest)
(2) 24: least sensitive (lowest)
N\
((a Y WEATHERPROOF IR CAMERA
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify MOTION DETECTED area.
- Select TOF, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the AREA
using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (8~126)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (8~126)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (4~191)
(4) RIGHT : extend or reduce the right side of the MOTION DETECTED area (4~191)
TOP reduce RIGHT extend
i и
Tm т то Ci
: i a 4
0 о
LEFT «=> 1 &-> RIGHT 1 } ;
i | на
! и E
| 0 a
Th N 3
„Й „= > -
BOTTOM a о
5) INITIAL : To reset the MOTION DETECT mode.
- select INITIAL using the UP or DOWN button. You can reset the MOTION DETECT mode using the
MENU button.
6) RETURN :To return to IMAGE ADJ MENU
- select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU 23
button.
KL
WEATHERPROOF IR CAMERA Г, Mm )
6. PRIVACY Y paEa ca ERES ANE NE EC CES EAN ERRE ETENEN NENE ESE ED, =
- Select PRIVACY using the UP or DOWN button and + Lda
press the MENU button to active the PRIVACY option. + АНЕА !
+ DISPLAY OFF
COLOR WHITE
TOP 15
+ BOTTOM 31
1) AREA : To specify the PRIVACY area ОНТ pr |
- Select AREA using the UP or DOWN button. You can + INITIAL ON
select area from 1-4 position using the LEFT or RIGHT 1 ti -
button. м
2) DISPLAY : To display the Privacy Zone area f 1 2
- Select DISPLAY using the UP or DOWN button. You can |
select between ON/OFF using the LEFT or RIGHT button. | 3 A |:
(1) ON : display the Privacy Zone area -. — —
(2) OFF : disable
3) COLOR : To change color of privacy zone
- Select COLOR using the UP or DOWN button. You can
adjust from WHITE, YELLOW, GREEN, BLUE, RED, BLACK,
24 or GRAY using the LEFT or RIGHT button.
N\
(С Y WEATHERPROOF IR CAMERA
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify PRIVACY ZONE area
- Select TOF, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the privacy
zone using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (4-63)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (5~64)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (18-205)
(4) RIGHT : extend or reduce the right side of the MOTION DETECTED area (19~206)
TOP reduce RIGHT extend
оно в
| — Ш H Ё
- -
LEFT €} 1 € RIGHT eT lem | =
: Ч 0 Е
it | „m
BOTTOM - -
5) INITIAL : To reset to factory default only on the PRIVACY mode.
- Select INITIAL using the UP or DOWN button. You can reset the PRIVACY mode using the MENU
button.
6) RETURN :lo return to IMAGE ADJ MENU +
- select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU 25
button.
EZ
WEATHERPROOF IR CAMERA Ч 2))
7. COLOR GAIN
- Select COLOR GAIN using the UP or DOWN button and
press MENU button to activate COLOR MODE option.
8. INITIAL :
lo reset to factory default only on the IMAGE ADJ mode.
- Select INITIAL using the UP or DOWN button and reset the
IMAGE ADJ mode using the MENU button.
9. RETURN :
To return to MAIN MENU
- select RETURN using the UP or DOWN button and return
to MENU using the MENU button.
COLOR GAIN
RY | В
BY | Ш
EXIT - MENU +
1. R-Y : To adjust density of RED (0-20)
2. B-Y : To adjust density of BLUE (0-20)
( a Y WEATHERPROOF IR CAMERA
Select GENERAL using the UP or DOWN button and + m :
press the MENU button to activate the GENERAL mode. :: ID DISPLAY OFF
+ CAM TITLE OFF
LANGUAGE ENG
SYNC INT
BAUDRATE 2400
VERSION
INITIAL ON
GENERAL
1. CAM ID : CAMERA ID ( RS-485 Communication 1D)
- Select CAM ID using the UP or DOWN button. You can select between the range 000-255
using the LEFT or RIGAT button.
NOTICE : CAM ID does not reset after user setting.
2. 1D DISPLAY (CAMERA ID DISPLAY)
- Select ID DISPLAY using the UP or DOWN button. You can select between ON/OFF using the
LEFT or RIGHT button.
(1) ON - lo display camera ID on the screen
(2) OFF: disable
WEATHERPROOF IR CAMERA
3. CAM TITLE Oj came
- Select CAM TITLE using the UP or DOWN button. E
You can adjust ON/OFF using the LEFT or RIGHT button. + a
(1) ON : lo display the camera title on the screen : UP/DN - CHAR SELECT
(2) OFF : disable + LE/AI - POSITION
+ EXIT - MENU +
- Select ON and Press MENU button to display CAM TITLE. ap rd dd a
(1) UP/DN : To select character using the UP or DOWN button (0-9,A-7)
(2) LE/AI : lo select position using the LEFT or RIGHT button.
4. LANGUAGE - Select LANGUAGE using the UP or DOWN button. You can change between
ENG or CHN using the LEFT or RIGHT button.
5. SYNC - Internal synchronization Type : INT
6. BAUDRATE
7. VERSION
WEATHERPROOF IR CAMERA
8. INITIAL : To reset to factory default only on the GENERAL mode.
- Select INITIAL using the UP or DOWN button. You can reset to factory default for GENERAL
mode using the MENU button.
9. RETURN : To return to MENU
- Select RETURN using the UF or DOWN button. You can return to the MENU using the MENU
button.
NINE: : To reset to factory default.
- Select INITIAL using the UP or DOWN button and reset to factory default using the MENU button.
EXIT : To exit out from the OSD setup menu.
- Select EXIT using the UP or DOWN button and close the OSD setup menu by pressing MENU
button.
WEATHERPROOF IR CAMERA Ÿ M )
( 12V DC Input Model O 8. SPECIFICATION
MODEL HIGH RESOLUTION
Signal System NTSC PAL
Image Sensor | 1/3" High Sensitivity CCD
Effective Pixels 752(H)x582V)
Video Output | Composite : 1.0V p-p, 750
Sync. System Internal Sync
S/N Ratio | 50dB Min.(SHARPNESS, AGC off)
Horizontal Resolution 600 TVLines (BW 650 TVLines)
Min Illumination 0.05 Lux (color) / 0.005 Lux (ICR, B/W)
(F1.2, 30IRE, AGC Max) 0.00Lux (IR LED ON)
ESC (NTSC-1/ 60 ~ 1/ 120,000), (PAL - 1/ 50 ~1/ 120,000)
1/ 60(1/50), 1/120(1/100), 1/ 250, 1/ 500, 1/ 700, 1/ 1K,
1/ 1.6K, 1/ 2.5K, 1/ 5K, 1/ 7K, 1/ 10K, 1/ 30K, 1/ 60K, 1/ 120K
DNR OFF, LOW, MIDDLE, HIGH
White Balance | FATTO YR NE
SBLC OFF, LOW, MIDDLE, HIGH
Manual Shutter
WEATHERPROOF IR CAMERA
(^^
12V DC Input Model )
AGC ON, OFF
Day / Night IRED, COLOR, B/W
Burst ON, OFF
Motion Detection ON, OFF (4 Programmable Zone)
Privacy ON, OFF (4 Programmable Zone)
Mirror ON(HORIZONTAL), OFF
Sharpness 1-20
OSD Language English
Applicable Lens DC Iris Lens
Supply Voltage DC 12V (+20% -20%)
Power Consumption 400mA / 4.8W (Max)
Operating Temperature/ Humidity -10°C to +50°C / 30% to 80% RH
Storage Temperature/ Humidity -20°C to +60°C / 20% to 90% RH
WEATHERPROOF IR CAMERA Ÿ ~ )
e 9. TROUBLESHOOTING
It you have trouble operating your camera, refer to the following guidelines. If the guidelines do
not help you to solve the problem, contact an authorized technician.
Nothing appears on the screen
D
FJ Check that the power cord and line connection between the camera and monitor are fixed properly.
E) Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
The image on the screen is dim a
E) |s lens stamed with dirt? Clean your lens with soft, clean cloth.
E) Set the monitor to proper condition.
E) If the camera is exposed to too strong light, change the camera position.
EJ Adjust the lens’ focus properly.
The image on the screen is dark
¥2 Adjust the contrast feature of the monitor.
к) If you have an intermediate device, set the 750 / Hi-z properly.
E) Adjust DC Level, VR level properly.
The camera is not working properly, and the surface of the camera is hot.
о
FE) Check that you have properly connected the camera to an appropriate power source.
The image on the screen flickers.
о
E) Check whether the camera Is exposed to strong sunlight or fluorescent lighting.
ME М IR CAMERA
e MEMO
WEATHERPROOF IR CAMERA € A y\\
® МЕМО
GE Te IR CAMERA
e MEMO
WEATHERPROOF IR CAMERA
WEATHERPROOF |R CAMERA SERIES
a \
P/N: 3810-0216D (Ver. 1006E) À
Design and specifications are subject to change without notice.
Ч Catt o

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement