CNB XCM-20VF/XCM-21VF Owner's Manual

Add to my manuals
35 Pages

advertisement

CNB XCM-20VF/XCM-21VF Owner's Manual | Manualzz
 Fry m 3 Frat
a , o
a = E = | TE i, er Sk TT
= a Ciba er Bd FP = Fan : a E ml 5 Ане CET AE dE RER
e y; OR - : Tu a = | 4) Ч — mu Fri г | 1 = ez Fo le Led i
a © ER Ova тат. в a : ; FE e arte ña E - 1 A TUU = sa 4 +t! =a Ea Do я gr
ï Е = Ce". = - и * [e lL
ñ Er x г = = Тени A pe La a Ths ET
- BT TOT fh NN a rT rE aN a ра о Ta Tre a th
- Pp ¿br ar ME = E x Ty ui rr E ri hls TRS
MER Ce PS TER nS =
aa a MAL A ETT ЧА or a TI TTC en CR
p F AD E — 5 i Te a La a To A. = de y я
=> ; Te a 1 oy epi PA CE A 1 JE .
UWNER'S MANUAL
Intelligent IR Technology
« 1/3" High Sensitivity CCD
* Ultra High Resolution (600TVL)
* Selectable, Day 6 Night
* Privacy Zone
COLOR GCD DSP DIGITAL DI GITAL GO Mi В
USER INFORMATION
7 RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION! TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
ЛМ the user to the presence of un-insulated “dangerous voltage” within the product's enclosure
that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence
of important operating and maintenance-(servicing) instructions in the literature accompanying
the appliance.
THE GRAPHIC SYMBOLS WITH SUPPLEMENTAL MARKING ARE ON THE BOTTOM OF THE SYSTEM.
“WARNING-TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE.”
USER INFORMATION
INFORMATION
This equipment has been tested and found to comply with limits for a Class A digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment
IS operated In a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their own expense.
WARNING
Changes or modifications not expressly approved by the manufacturer could void the user's authority to Operate
the equipment.
CAUTION
To prevent electric shock and risk of fire hazards:
* Do not use power sources except for that specified.
* Do not expose this appliance to rain or moisture.
| This installation should be made by a qualified service person and should abide to all local codes. ]
CONTENTS
Thank you for purchasing this COLOR VIDEO CAMERA.
Before using this camera, please read this operation manual carefully
to obtain the best result and keep this manual for feature reference.
1. SAFETY INSTRUCTIONS — ----------------=-=e-e<eeeeeenaeanenans 5
2. PRECAUTIONS -----------————m—mm—n—nanannanan anna enanas 6
3. FEATURES — 7
4. NAME AND FUNCTIONS ----<-<----<-<--0-0n0ecenccencncenncncnencnes 8
5. CONNECTIONS -----------=-=——memnnnnnannenannnnen nana 9
6. COMPOSITION —-------------=-=-===eeeeeeeeneennane nana 10
7. OPERATING CAMERA —---—-<-<<-<=<====<=<e<cecenesceneecenenencennss 11
8. SPECIFICATION ETI ED 30
24V AC / 12V DC Input Model
9. TROUBLESHOOTING ---<--<--<--<-<<=<<=<<=<cescencencene scene scene 34
1. SAFETY INSTRUCTIONS
Read Instructions
Ч
Read all of the safety and operating instructions
before using the product.
Installation
a
Do not place this product on an unstable cart,
stand, or table. The product may fall causing
serious injury to a child or adult, and damage
to the product.
Use only with a cart or stand recommended
by the manufacturer, or sold with the product.
Mounting should follow the manufacturer's
instructions, and should use a mounting accessory
recommended by manufacturer.
Retain Instructions
Save this instructions for later use.
Cleaning
Unplug this appliance from wall outlet before
cleaning. Do not use liquid cleaners or aerosol
cleaners. Use a damp cloth for cleaning.
Power source
+
This product should be operated only trom
the type of power source indicated on the
marking label.
If vou are not sure of the type of power supplied
to your home, consult your dealer or local
power company.
2. PRECAUTIONS
2 Do not install the camera in extreme temperature conditions.
Operate the camera under conditions where temperatures are within -10°C to 50°C.
Especially be careful for ventilation under high temperature.
> Do not install the camera under unstable lighting conditions.
Severe lighting change or flicker can cause the camera to work improperly.
2 Never use the camera close to a gas or oil leak.
It can cause malfunctions to occur.
2 Do not disassemble the camera.
There are no user repairable parts inside.
> Do not drop the camera or subject them to physical shocks.
It can cause malfunctions to occur.
2 Never keep the camera face to strong light directly.
It can damage CCD.
NOTE When this camera is installed near wireless communication devices that emits
strong electromagnetic field, irregularity such as noise on the monitor may appear.
|
3. FEATURES
1. Intelligent IR Technology
"Intelligent IR" technology dramatically eliminates the white out effect and saturation on close objects,
producing a clear and recognizable image regardless of viewing condition or location of objects.
2. 1/3” High Sensitivity CCD
3. Min Illumination (F1.2, 30IRE, AGC Max)
- 0.05 LUX (COLOR)
- 0.005 LUX (ICR, B/W)
- 0.00 LUX (IR LED ON)
4. High performance menus for functions
- Ultra High Resolution (600TVL)
- SBLC (Super Back Light Compensation)
- DNR (Digital Noise Reduction)
- Privacy zone selectable.
- MIRROR (HORIZONTAL)
- Flickerless On/Off.
4. NAME AND FUNCTIONS
Vari-focal Lens Type
() IRLED
850nm / 30°(42EA)
¢) Focus Handle
Used to provide for accurate focusing
of object within the lens field of view.
© Zoom Handle
Used to adjust zoom magnification by
turning. O - O
5. CONNECTIONS
Connecting to Monitor and Power
9 For 12V DC Power Type й Video Output ]
- Connect the videc-out jack to the video-in jack of monitor.
- Connect the power adapter to the power input connector.
- Use 12V DC power source.
GND
1.0Vp.p
12V DC(+10%), 500mA / 6W (Max)
Video Output
9 For 24V AC/ 12V DC Power Type
- Use 24V AC power source or 12V DC power source.
Remark
10Vp.p
AC 480mA / 6.6W (Max),
DC 460mA / 5.5W (Max)
6. COMPOSITION
SIS = —2 -—
Bracket Mounting Screws Sunshield Fastener
; =
DC Cable Sub Video Cable
7. OPERATING CAMERA
ESC BRIGHTNESS | 0-5
DC LEVEL 0-5
LENS DC 1/00(1/50),1/120(1/100), 1/250,1/200,1/700,1/1k., 171600, 17/2500
SHUTTER 1/5K,1/7K,1/10K,1/30K,1/60K,1/120K
IR MODE: 1/60(1/50)
ATW
RED 0-160
WHITE BAL MANUAL e а чан
PUSH a
AGC ON LEVEL 0-20 (IR MODE:FIXED)
OFF
REL ANGE LEVEL SW ВОО HIER
DAY / NIGHT A
B/W BURST ON/OFF
SBLC OFF, LOW, MIDDLE, HIGH
DNR OFF, LOW, MIDDLE, HIGH
SHARPNESS LEVEL 0-20
MIRROR OFF, ON
AREA 1-4
DISPLAY OFF ON
IMAGE ADJ SENSITIVITY 1-24
ТОР 8-126
MOTION BOTTOM 8-126
LEFT 4-191
RIGHT 4.191
INITIAL OFF, ON
RETURN +
AREA 1-4
— DISPLAY OFF ON
COLOR WHITE, YELLOW, GREEN, BLUE, RED, BLACK, GRAY
TOP 4-63
PRIVACY | BOTTOM 5-64
[ LEFT O 18~205
RIGHT 19-206
IMAGE ADJ —NTAL — OFF=1.ÓN
— RETURN pr
R-Y 0-20
COLOR GAIN E 0
INITIAL OFF=-, ON
RETURN e
CAM ID 0~255
ID DISPLAY OFF ON
CAM TITLE OFF
ON UP/ DN. LE/ RI
LANGUAGE ENG
SRSA SYNC NT
BAUDRATE 2400, 4800, 9600, 57600
VERSION
INITIAL OFF ON
_ RETURN pu
INITIAL OFF. ON
— RETURN +
Use the joystick to navigate between 5 ways.
: E) DOWN : Move down
: (D UP : Move up
: @ LEFT : Move left
@ MENU(SET):
Press the joystick in its straight position.
) Sevice Monitor Connecter :
Use service monitor connector to set camera
angle & focus when installing.
(Image cannot be seen if monitor output and service
video output is used simultaneously.)
MAIN MENU - GENERAL
Press MENU button to access the SETUP menu.
Select each sub-menu by using the «, p , 4 Y button.
Press the MENU(SET) button to select.
F
MENU
LENS
WHITE BAL
AGC
DAY/NIGHT
IMAGE ADJ
GENERAL
INITIAL
EXIT
DC +
ATW
ON +
IRED +
ON
If the OSD MENU is changed then INITIAL will be OFF «
(EXCEPT : LENS, CAM ID, BAUDRATE)
Press the MENU button to access the SETUP menu.
- Select LENS using the UP or DOWN button. You can change
between ESC and DC using the LEFT or RIGHT button.
Select ESC and Press MENU button to display LENS ESC.
1. BRIGHTNESS
- Select BRIGHTNESS using the UP or DOWN button.
You can adjust between O - 5 using the LEFT or RIGHT button.
MENU
LENS ESC +
WHITE BAL ATW
AGC ON «
DAY/NIGHT НЕО +
IMAGE ADJ +
GENERAL +
INITIAL ON
EXIT +
LENS ESC
BRIGHTNESS | i
EXIT - MENU
Select DC and Press the MENU button to have
LENS DC activated. DCLEVEL | i |
FLK OFF
SHUTTER 1/60
| EXIT - MENU |
1. DC LEVEL(Adjusts brightness of the image.)
- Select DC LEVEL using the UP or DOWN button. You can adjust between 0 ~ 5 level using the LEFT or
RIGHT button.
2. FLK (FLICKERLESS)
- Select FLK using the UP or DOWN button. You can select between ON / OFF using the LEFT or RIGHT button.
> OFF : You will be allowed to adjust the shutter speed.
3. SHUTTER (Adjusts the shutter speed of the lens.)
- IR LED Mode : 1/60(1/50)
- COLOR, B/W Mode : Select SHUTTER using the UP or DOWN button. You can adjust from 1/60(1/50),
1/120(1/100), 1/250, 1/500, 1/700, 1/1K, 1/1600, 1/2500, 1/5K, 1/7K, 1/10K, 1/30K, 1/60K, 1/120K(sec)
level using the LEFT or RIGHT button.
WHITE BAL (White Balance)
Select WHITE BAL using the UP or DOWN button. You can select from ATW, MANUAL, PUSH
using the LEFT or RIGHT button.
1. ATW : Color temperature is automatically adjusted to 2,000°K ~ 10,000°K
2. MANUAL : To set a certain color temperature with RED CONT, BLUE CONT
- Select MANUAL using the UP or DOWN button and press the MENU button to activate WB MANUAL option.
"a
WB MANUAL
BLUE | i |
EXIT - MENU
1. RED : To adjust density of RED (0~160)
2. BLUE : To adjust density of BLUE (0-160)
3. PUSH : If the set color temperature does not meet your environment, press the MENU button to adjust
the color temperature to desired setting.
AGC (Automatic Gain Control)
Select AGC using the UP or DOWN button. You can select between OFF, ON using the LEFT or
RIGHT button.
AGC is fixed at a certain level in IR LED mode.
AGC level is selectable in COLOR, B/W mode.
1. ON : Select ON using the LEFT or RIGHT button and press the MENU button to activate AGC option.
LEVEL
1. LEVEL : You can adjust between 0~20 using the LEFT or RIGHT button. (Color, B/W)
2. IRED MODE AGC “20" MAX Fixed
2. OFF : Disable the AGC
AGC
EXIT - MENU
A
DAY / NIGHT
Select DAY / NIGHT using the UP or DOWN button.
You can select between IRED, COLOR, B/W using the LEFT or RIGHT button.
1, COLOR : for color mode only (DAY mode)
2. B/W : for BLACK and WHITE mode only (NIGHT mode)
- Select B/W using the LEFT or RIGHT button and press the MENU button to activate COLOR BURST
option.
COLOR BURST
BURST ON
EXIT - MENU
hey r
It is possible to select ON/OFF using the LEFT or RIGHT button.
3. IRED : IR LED control mode
WIDE : It controls the IR LED(full screen base), Saturation may be expected depending on the installation
environment.
SMART : It controls the IR LED(bright portion base), Satuation is not expected however, Image may be
darker.
IR LED
MODE WIDE
CHANGE LEVEL MIDDLE
EXIT_MENU
IMAGE ADJ (Image Adjust)
Select IMAGE ADJ using the UP or DOWN button and press the MENU button to activate
the IMAGE ADJ mode.
IMAGE ADJ
SBLC
DNR
SHARPNESS
MIRROR
MOTION
PRIVACY
COLOR GAIN
INITIAL
RETURN
LOW
LOW
«+
OFF
+
+
+
ON
++
wy
d
1. SBLC(Super Back Light Compensation) : To lighten a darker part of the image
- Select SBLC using the UP or DOWN button. You can select between OFF, LOW, MIDDLE, HIGH
using the LEFT or RIGHT button.
- SBLC turns to OFF automatically at night.
2. DNR(Digital Noise Reduction) : To reduce the image noise especially during the low ambient
- Select DNR using the UP or DOWN button. You can adjust between OFF, LOW, MIDDLE, HIGH
using the LEFT or RIGHT button.
lighting conditions.
3. SHARPNESS : To adjust SHARPNESS of the image.
- Select SHARPNESS using the UP or DOWN button.
- Select «1 and press the MEUN button to activate HARPNESS option.
- You can adjust the sharpness from 0~20 using the LEFT or
RIGHT button.
4. MIRROR
- Select MIRROR using the UP or DOWN button.
You can select from ON/OFF using the LEFT or RIGHT button.
(1) ÓN : Horizontal image flip.
(2) OFF : default
5. MOTION(Motion Detect) Display only(No output signal)
- Select MOTION using the UP or DOWN button and
press MENU button to activate MOTION DETECT option.
SHARPNESS
LEVEL | 3
EXIT - MENU
MOTION
AREA
DISPLAY
SENSITIVITY
TOP
BOTTOM
LEFT
RIGHT
INITIAL
RETURN
OFF
5
19
62
13
89
1) AREA : To specify MOTION DETECTION area
- Select AREA using the UP or DOWN button. You can select from area
1~4 position using the LEFT or RIGHT button.
2) DISPLAY : To display MOTION DETECTED area on the video
- Select DISPLAY using the UP or DOWN button. You can select
between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the MOTION DETECTED area on the screen
(2) OFF : disable
=) [9/2
I~)
3) SENSITIVITY : lo setup the motion sensitivity
- Select SENSITIVITY using the UP or DOWN button. You can adjust the motion sensitivity of
a movement from 1-24 using the LEFT or RIGHT button.
(1) 1: most sensitive (highest)
(2) 24 : least sensitive (lowest)
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify MOTION DETECTED area.
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the AREA
using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the MOTION DETECTED area (8-16)
(2) BOTTOM : extend or reduce the bottom area of the MOTION DETECTED area (8~126)
(3) LEFT : extend or reduce the left side of the MOTION DETECTED area (4~191)
(4) RIGHT : extend or reduce the right side of the MOTION DETECTED area (4~191)
a reduce RIGHT extend
Y
LEFT 1 RIGHT 1
T
Y
BOTTOM
5) INITIAL : To reset the MOTION DETECT mode.
- Select INITIAL using the UP or DOWN button. You can reset the MOTION DETECT mode using the
MENU button.
6) RETURN :To return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU
button.
Î
6. PRIVACY
- Select PRIVACY using the UP or DOWN button and press
the MENU button to active the PRIVACY option.
1) AREA : To specify the PRIVACY area
- Select AREA using the UP or DOWN button. You can select
area from 1~4 position using the LEFT or RIGHT button.
2) DISPLAY : To display the Privacy Zone area
- Select DISPLAY using the UP or DOWN button. You can
select between ON/OFF using the LEFT or RIGHT button.
(1) ON : display the Privacy Zone area
(2) OFF : disable
3) COLOR : To change color of privacy zone
- Select COLOR using the UP or DOWN button. You can
adjust from WHITE, YELLOW, GREEN, BLUE, RED, BLACK,
or GRAY using the LEFT or RIGHT button.
PRIVACY
AREA 1
DISPLAY OFF
COLOR WHITE
TOF 15
BOTTOM 31
LEFT 44
RIGHT 104
INITIAL ON
RETURN +
3/4
4) TOP / BOTTOM / LEFT / RIGHT : Users can specify PRIVACY ZONE area
- Select TOP, BOTTOM, LEFT, or RIGHT using the UP or DOWN button. You can adjust the privacy
zone using the LEFT or RIGHT button.
(1) TOP : extend or reduce the upper area of the PRIVACY area (4-63)
(2) BOTTOM : extend or reduce the bottom area of the PRIVACY area (5-64)
(3) LEFT : extend or reduce the left side of the PRIVACY area (18-205)
(4) RIGHT : extend or reduce the right side of the PRIVACY area (19-206)
TOP reduce RIGHT ‘extend
\%
LEFT <— 1 E RIGHT 1
T
\
BOTTOM
1
1
5) INITIAL : To reset to factory default only on the PRIVACY mode.
- Select INITIAL using the UP or DOWN button. You can reset the PRIVACY mode using the MENU button.
6) RETURN : То return to IMAGE ADJ MENU
- Select RETURN using the UP or DOWN button. You can return to IMAGE ADJ MENU using the MENU
button.
7. COLOR GAIN
- Select COLOR GAIN using the UP or DOWN button and press MENU button to activate
COLOR MODE option.
COLOR GAIN
RY | Е
BY | i
EXIT - MENU
1. R-Y : To adjust density of RED (0-20)
2. B-Y : To adjust density of BLUE (0-20)
8. INITIAL : To reset to factory default only on the IMAGE ADJ mode.
- Select INITIAL using the UP or DOWN button and reset the IMAGE ADJ mode using the MENU button.
9. RETURN : To return to MAIN MENU
- Select RETURN using the UP or DOWN button and return to MENU using the MENU button.
GENERAL
Select GENERAL using the UP or DOWN button and press
the MENU button to activate the GENERAL mode.
1. CAM ID : CAMERA ID ( RS-485 Communication ID)
- Select CAM ID using the UP or DOWN button. You can select between the range 000-255 using
the LEFT or RIGHT button.
NOTICE : CAM ID does not reset after user setting.
2. ID DISPLAY (CAMERA ID DISPLAY)
- Select ID DISPLAY using the UP or DOWN button. You can select between ON/OFF using the
LEFT or RIGHT button.
(1) ÓN : To display camera ID on the screen
(2) OFF : disable
GENERAL
CAM ID
ID DISPLAY
CAM TITLE
LANGUAGE
SYNC
BAUDRATE
VERSIÓN
INITIAL
RETURN
OFF
OFF
ENG
INT
2400
ON
3. CAM TITLE
- Select CAM TITLE using the UP or DOWN button.
You can adjust ON/OFF using the LEFT or RIGHT button.
(1) ÓN : To display the camera title on the screen
(2) OFF : disable
- Select ON and Press MENU button to display CAM TITLE.
+ CAM TITLE
UP/DN - CHAR SELECT
LE/RI - POSITION
EXIT - MENU
(1) UP/DN : To select character using the UP or DOWN button (0-9,A-Z)
(2) LE/RI : To select position using the LEFT or RIGHT button.
4, LANGUAGE - Select LANGUAGE using the UP or DOWN button. You can change between
ENG or CHN using the LEFT or RIGHT button.
5. SYNC - Internal Synchronization Type : INT
6. BAUDRATE
7. VERSION
8. INITIAL : To reset to factory default only on the GENERAL mode.
- Select INITIAL using the UP or DOWN button. You can reset to factory default for GENERAL mode
using the MENU button.
9. RETURN : To return to MENU
- Select RETURN using the UP or DOWN button. You can return to the MENU using the MENU button.
LLL : To reset to factory default.
- Select INITIAL using the UP or DOWN button and reset to factory default using the MENU button.
SU : To exit out from the OSD setup menu.
- Select EXIT using the UP or DOWN button and close the OSD setup menu by pressing MENU button.
8. SPECIFICATION
12V DC Input Model
MODEL
Signal System
Image Sensor
Effective Pixels
Video Output
sync. System
S/N Ratio
Horizontal Resolution
Min Illumination
(F1.2, 30IRE, AGC Max)
ESC
IR LED
IR LED Visible Range
Manual Shutter
HIGH RESOLUTION
NTSC | PAL
1/3” High Sensitivity CCD
768(H)x494(V) | 752(H)x582(V)
Composite : 1.0V P-P, 750
Internal Sync
50dB Min.(SHARPNESS, AGC off)
600 TV Lines (BW 650 TV Lines)
0.05 Lux (color) / 0.005 Lux (ICR, B/W)
0.00 Lux (IR LED ON)
1/60 ~ 1/120,000 | 1/50 ~ 1/120,000
Intelligent IR, IR LED 42EA
Max. 35m
1/60(1/50), 1/120(1/100), 1/250, 1/500, 1/700, 1/1K,
1/1.6K, 1/2.5K, 1/5K, 1/7K, 1/10K, 1/30K, 1/60K, 1/120K
DNR
White Balance
SBLC
AGC
Day / Night
Burst
Motion Detection
Privacy
Mirror
Sharpness
05D Language
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature/ Humidity
Storage Temperature/ Humidity
OFF, LOW, MIDDLE, HIGH
ATW, MANUAL, PUSH
OFF, LOW, MIDDLE, HIGH
ON, OFF
IRED, COLOR, B/W
ON / OFF
ON, OFF (4 Program Zone)
ON, OFF (4 Program Zone)
ON(HORIZONTAL), OFF
1-20
English
DC lris Lens
12V DC (+10%)
500mA / 6W (Max)
-10°C to +50°C / 30% to 80% RH
-20°C to +60°C / 20% to 90% RH
24V AC /12V DC Input Model
MODEL
Signal System
Image Sensor
Effective Pixels
Video Output
Sync. System
S/N Ratio
Horizontal Resolution
Min lllumination
(F1.2, 30IRE, AGC Max)
ESC
IR LED
IR LED Visible Range
Manual Shutter
HIGH RESOLUTION
NTSC | PAL
1/3” High Sensitivity CCD
768(H)x494(V) 752(H)x582(V)
Composite : 1.0V P-P, 750)
Internal Sync
50dB Min.(SHARPNESS, AGC off)
600 TV Lines (BW 650 TV Lines)
0.05 Lux (color) / 0.005 Lux (ICR, B/W)
0.00 Lux (IR LED ON)
1/60 - 1/120,000 | 1/50 - 1/120,000
Intelligent IR, IR LED 42EA
Max. 35m
1/60(1/50), 1/120(1/100), 1/250, 1/500, 1/700, 1/1K,
11.6K, 1/2.5K, 1/5K, 1/7K, 110K, 1/30K, 1/60K, 1/120K
DNR
White Balance
SBLC
AGC
Day / Night
Burst
Motion Detection
Privacy
Mirror
Sharpness
OSD Language
Applicable Lens
Supply Voltage
Power Consumption
Operating Temperature/ Humidity
Storage Temperature/ Humidity
OFF, LOW, MIDDLE, HIGH
ATW, MANUAL, PUSH
OFF, LOW, MIDDLE, HIGH
ON, OFF
IRED, COLOR, B/W
ON / OFF
ON, OFF (4 Program Zone)
ON, OFF (4 Program Zone)
ON(HORIZONTAL), OFF
1-20
English
DC Iris Lens
24V AC(+10%), 12V DC(+10%)
AC 480mA/6.6W(Max), DC 460mA/5.5W(Max)
-10°C to +50°C / 30% to 80% RH
-20°C to +60°C / 20% to 90% RH
9. TROUBLESHOOTING
If you have trouble operating your camera, refer to the following guidelines. If the guidelines do
not help you to solve the problem, contact an authorized technician.
Nothing appears on the screen
Y Check that the power cord and line connection between the camera and monitor are fixed properly
\м” Check that you have properly connected VIDEO cable to the camera VIDEO output jack.
The image on the screen is dim
Y ls lens stained with dirt? Clean your lens with soft, clean cloth.
«/ Set the monitor to proper condition.
Vv" If the camera is exposed to too strong light, change the camera position.
Y Adjust the lens’ focus properly.
The image on the screen is dark
+" Adjust the contrast feature of the monitor.
w If you have an intermediate device, set the 750 / Hi-z properly.
The camera is not working properly, and the surface of the camera is hot.
w Check that you have properly connected the camera to an appropriate power source.
The image on the screen flickers.
Y Check whether the camera is exposed to strong sunlight or fluorescent lighting.
WEATHERPROOF IR CAMERA
WEATHERPROOF IR CAMERA SERIES
у >
P/N : 3810-0228A1 (Ver.1104E) sd
Design and specifications are subject to change without notice.
_ — 7

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement