Formax FD402P1 Single
Bin Paper Jogger
Instruction Manual
402 Series Joggers
8/2010
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
OPERATOR MANUAL
SECOND EDITION
TABLE OF CONTENTS
TOPIC
INTRODUCTION
SPECIFICATIONS
INSTALLATION
OPERATION
TROUBLESHOOTING
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
PAGE
1
1
1
2
2
INTRODUCTION
The Formax 402 Series Joggers are used for aligning paper and dissipating static electricity. An electromagnetic assembly produces a vibrating action, which is transmitted to the deck and rack through a system of flex plates.
The control assembly consists of a solid-state on-off knob which also serves to control the vibration intensity, up to 4,000 vibrations per minute.
Refer to this Maintenance Manual prior to adjusting or performing service on the jogger.
WARNING: Failure to follow these instructions could result in unsatisfactory jogger performance, machine damage or shortened service life, or personal injury.
FD 402P1 FD 402P3 FD 402E2
Bin Capacity:
Bin Size:
Media Size:
Dimensions:
FD 402P1 FD 402P3
Up to 800 sheets of 20# paper Up to 1,700 sheets 20#
3.5” D x 8.75” W x 15.5” L
Up to 11” W x 17” L
7.75” W x 19” L x 21” H
FD 402E2
Up to 1,750 sheets 20#
2.5” D x 3.5” W x 10” L each 7” D x 2.25” W x 11.25” L each
Up to 8.5” W x 14” L
9.75” W x 14” L x 17.75” H
Up to 4” W x 8” L
8.125” W x 8.125” L x 13.125” H
28 lbs.
Weight:
Variable Speed:
28 lbs.
Up to 4,000 vibrations/minute
29 lbs.
Voltage: 115 Volts (50/60 Hz) / Export 230 Volts (50/60 Hz)
Safety Certifications: TUV & CE applied for
INSTALLATION
Inspect the jogger for damage which may have occurred during shipment. If any damage is found, immediately notify the shipping carrier and your authorized Formax dealer.
Each jogger weighs approximately 30 pounds. Lift the jogger only by the base. Lifting by the bin or top cover may cause damage or injury.
WARNING: The voltage and frequency of the power supply must be as specified on the nameplate. A power supply of another rating may cause damage to the unit.
Locate the jogger on a solid support surface. The support must not vibrate while the jogger is operating. The bin or top cover must not be in contact with any rigid object or adjacent surface; it must be free to vibrate.
1
OPERATION
Place the jogger in its operating location and plug it into a self-governing electrical receptacle.
Place paper, envelopes or checks in the jogger bin(s) and turn the power/ vibration control knob clockwise to turn the jogger on and adjust vibration.
The vibration amplitude is changed by turning this knob. To turn the jogger off, turn control knob all the way to counter clockwise until it clicks off. Note: FE models eith serial # ending in “F” have an on/off switch, the control knob only adjusts the vibration intensity
For best results, documents should be jogged for at least 15 to 30 seconds. For maximum efficiency, Formax recommends a maximum load of 10 pounds for each of the 402 Series models.
TROUBLESHOOTING
PROBLEM:
Unit does not operate
Unit has power but will not vibrate
Excessive noise when operating
POSSIBLE CAUSE:
Defective control knob
Shorted wiring, loose connection, no power to unit
Unit in contact with rigid object or adjacent surface
Defective controller
Defective flex plates
Armature and core assemblies making contact
SOLUTION:
Replace control knob
Repair
Isolate unit
Replace controller
Replace flex plates
Air gap spacers may need to be replaced or adjusted
MyBinding.com
5500 NE Moore Court
Hillsboro, OR 97124
Toll Free: 1-800-944-4573
Local: 503-640-5920
2
