MyBinding Paitec ES5000 Desktop Folder and Pressure Sealer Manual

Paitec ES5000 LowVolume Desktop Folder
and Pressure Sealer
Instruction Manual
Pressure Sealer ES-5000
ES-5000
User Manual
<Rev. 09-01-30>
1
Pressure Sealer ES-5000
Table of Contents
1. Introduction
2. Installation
3. Features
1) Specifications
2) General views
4. How to Operate
1) Form Preparation
2) Loading forms
3) Start
4) Fold Setting
5) Operator Panel
6) Manual Feed
5. Maintenance
1) General Cleaning
2) Paper Dust
3) Cleaning Pickup and Fold Rollers
4) Cleaning Press Rollers
6. Trouble Shooting
1) Paper Jam
2) Double Feed
3) Mis-Feed
4) Skewed Fold
2
Pressure Sealer ES-5000
1. Introduction
ES-5000 produces folded and sealed mailable documents with cut-sheet Pressure Seal
forms. Pressure activated adhesive applied forms provide and instantly secure seal on all
sides of the form, whether use a “C”, “V”, “Z” or “Double” fold.
Names of each part
2.
3
Pressure Sealer ES-5000
2. Installation
4


Locate the box right next to the location where the machine will be set up and operate.
Open Box, Remove the Operators Guide and set aside. Grasp the two Shipping Straps
and remove the unit from the box.

Remove all packing materials from around the unit and place the folder on a sturdy
surface.

Open Infeeder Chute and Pull out Paper Stopper

Set up fold drum and run at least 50 documents through the machine. Show customer
how to run the machine.
Pressure Sealer ES-5000
1) Features
1) Specifications

















Processing Speed 4,200 forms per hour
Automatic jam recovery system
No adjustment required for varying paper thickness
Fold plate setting can be changed in seconds
Manual feeder for single form processing
Folding unit slides out for easy access and maintenance
Digital reset counter
Exceptionally quiet – approximately 45db
Infeeder capacity-150(24#), 120(28#)
Form Size: Letter, Legal(14” Z-fold available option)
Z,C,V & double fold
Paper Weights: 16 lb to 28 lb
Counter: reset counter
Jam Removal: folder unit slides out and opens
Size: 17.3 x 16.5 x 19 inches (L x W x H)
Weight: 80 lbs
Power: 120V/60Hz
2) General Views
2.1)
Folding Drum
Fold Position Lock Lever
Fold Type/Setting Chart
2
nd
Fold position Setting Lever
st
1 Fold position Setting Lever
2.2)
Feeding Unit
Movable Paper Guide Rollers
Spring-loaded Feed Table
5
Folding Drum Release Handle
Feed Roller
Slide these Tab up or down to decrease or
increase Feed Table spring lift tension to Aid in
feeding documents. Factory Preset Value is right
in the middle as shown above
Pressure Sealer ES-5000
2.3)
Exit Tray
Stopper for Exit Tray
2.4)
AC Socket
2.5)
Label & Fuse
5 Amp 250V Mini Fuse in a 1/4
Turn Fuse Holder
Manufacturer’s
Serial No.
with
How to Open the Fold Unit (Please follow the pictures below in order)
Folding Unit Pulls out by grasping the hand hold
and pull out
6
Label
Pressure Sealer ES-5000
2.6)
How to open the Fold Drum (Please follow the pictures below in order)
Folding Drum handle
in the Unlock(down)
position
Folding Drum in the
partially open position
Folding Drum in the open position.
Access the Folding Drum for clearing jams
7
Pressure Sealer ES-5000
3. How to operate
1) Form preparation
Forms must be fanned properly on both sides to separate and eliminate any static that
may have been induced by the laser printer
2) Loading forms
Place the paper in the Paper tray in the correct orientation as indicated in the chart
below. The Paper tray can hold up to about 120 sheets of pressure forms. To correctly
place your forms in the Paper tray, jog the forms so the stack is neat, push the Paper
tray back so the forms will rest on the solid plate and behind the feed roller. The Paper
tray is spring-loaded to apply the correct amount of pressure for proper feeding.
It is always a good idea to fold one form to verify that the fold settings are OK and have
not been changed. Adjust if necessary and then proceed to load your forms in the Paper
tray.
Form
Z-Fold
Z-Fold
C-Fold
V-Fold
Load in Paper Forms will deliver
tray
Address leading, Address side will be face up and document
Face Up
sequence will be reversed from the
sequence in the Paper tray
Address Trailing, Address side will be face down and
Face Down
document sequence will be reversed from
the sequence in the Paper tray
Address Trailing, Address side will be face up and document
Face Down
sequence will be the same as the
sequence in the Paper tray
Address Trailing, Address side will be face down and
Face Down
document sequence will be the same as
the sequence in the Paper tray
3) Start (Press Start button to fold & seal)
3.1 ) If the output is acceptable, Run the job
3.2 ) If the folded position is not correct, reset the fold position by readjusting the fold
guide.(Please use plain paper for a test run in order to find out more accurate the
fold position and compare the folded position with the perforation line on the forms)
8
Pressure Sealer ES-5000
4) Fold Setting
4.1) Standard Folding Drum
4.1.1) Unlock the green release lever to set the fold position
4.1.2) Move the red arrow, First fold on the red knob to the fold position required
according to the manual on the fold drum
4.1.3) Move blue arrow, Second fold according to the manual on the fold drum
4.1.4) Once the fold position properly is done, lock back the green release lever
(Red knob is the first fold setting, Blue know is the second fold setting)
Ex 1) “Z” fold with 8 1/2" x 11"
- Red knob “186”(First fold 186mm), blue knob “93”(Second fold 93mm)
Ex 2) “C” fold with Letter
- Red knob “92”(First fold 92mm), blue knob “94”(Second fold 94mm)
Ex 3) “V” fold with 8 1/2" x 11"
- Red knob “140”(First fold 140mm), blue knob “0”(Fully down, No Second
fold)
Note: Please note that although we suggest that you follow the fold
setting according to the manual, however the scale on the drum is NOT
100% accurate
9
Pressure Sealer ES-5000
5) Operator Panel
5.1) Power Switch: Power On/Off
5.2) Reset: Reset button will clear
the display count
5.3) Start/Stop: Start/Stop button
will start or stop the Feed cycle
5.4) Counter: Display will show the
total page count/resettable as
well as Firmware Rev. Level at
Start-up, Fold unit open and
Jam condition, please see the
pictures as below for the details
6) Manual Feed
6.1) Fold the form manually and insert the form to the manual feeder
6.2) Press Start button to run the machine
Note: This is ideal for the poorly sealed forms owing to evaporation of the glue
10
Pressure Sealer ES-5000
5.
Maintenance
1) General Cleaning
Be sure that the room is well ventilated, Switch off the mains power and unplug or
disconnect from the mains, Pull out the fold drum and the fold unit, Remove as much
paper dust as possible using a soft brush
2) Paper Dust
With general use, paper dust will build up inside the machine and can be cleared by
suing an can of invertible Air Duster, which will apply a short burst of compressed
air and clear any paper dust that may be present.
3) Cleaning Pick up and Fold rollers
Clean the pickup roller, aluminum and rubber roller in the Fold unit with roller
cleaning fluid such as an alcohol solution.
Pickup roller in Gray color
Aluminum & Rubber rollers
Caution:
Please do not use any gasolinic oils since it may damage the surface of the rubber
rollers!
Avoid breathing the fumes or getting the solution in an open wound or other sensitive
areas such as the eyes or mouth!
11
Pressure Sealer ES-5000
4) Cleaning Press Rollers
With general use, toner will build up on the Press rollers. Check the rollers for build
up and clean on a regular basis with roller cleaning fluid. Depending on the type of
laser printer, toner and fuser, the degree of build up will vary.
Clean both Upper & Lower Press
12
Pressure Sealer ES-5000
6.
Trouble Shooting
1) Paper Jam
1.1) Feeding Unit Jam
Do not pull the document backward in the
event of jam in the Infeeder.
Open the Fold Drum Unit by pushing
down the Fold Drum handle as the
direction of the red arrow in the picture
on the right
Pull the paper to the direction of the red
arrow as shown in the picture on the right
1.2)
Folding Unit Jam
Open the Fold Drum Unit by pushing
down the Fold Drum handle as shown in
the direction of the red arrow in the
picture on the right
Remove the document from the Folding
Drum as shown in the picture on the right
13
Pressure Sealer ES-5000
1.3)
Press Unit Jam
Fully extend the Folding Unit to the
direction of the red arrow in the picture on
the right
Use the Jam Removal Tool to rotate the
rollers by placing the tool into the jam
Removal holes as shown in the picture on
the right
Turn it downward. Remove the jam as
shown in the picture on the right
Tips: Correct any mis-folds and run the
form through the manual feed (please refer
to Chapter 4-6 for the details of the
manual feed)
1.4)
Out Feed Jam
In the event of jam in the Out-feed, the
display blinks
Push down the lower plate (with the
rollers) and remove the jam as shown in
the picture on the right.
14
Pressure Sealer ES-5000
2) Double Feed
2.1) Clean the Pickup rollers and pad with an
alcoholic solution(In case the problem
persists, then go to 2.2)
2.2)
Slide In-feed tray tension adjusters
upwards (Manufacturer’s default position:
middle). Both tension adjusters must be in
the same position as shown in the picture
on the right(In case the problem persists,
then go to 2.3)
2.3)
Replace in-feed roller and or Separator(Pad Base)
3) Mis-Feed
3.1) Clean In-feed roller and pad with an
alcoholic solution(In case the problem
persists, then go to 3.2)
3.2)
Move the In-feed tray tension adjusters
downwards until miss-feeding is resolved
as shown in the picture on the right(in case
of no improvement, then go to 3.3)
3.3)
Replace in-feed roller and/or Separator
(Pad Base)
4) Skewed Fold
4.1) Clean the In-feed roller and pad with an alcoholic solution
4.2) Check to make sure the side guides are not bent in any ways
4.3) Insure that there shouldn’t be too much gap between paper and the side guides as
shown in the picture below
4.4)
4.5)
4.6)
15
On adjustment screws are set correctly
Insure that the side guides are right up against the edge of the form but not
compressing the form
Look for foreign materials in the folding drum assembly
Pressure Sealer ES-5000
4.7)
4.8)
4.9)
Clean the fold rollers with an alcoholic solution
Examine and replace any folding roller with imperfections such as flat spots or
swelling
Replace or exchange from side to side the folding roller compression springs
Division of Pai Trading, Inc.
Headquaters & Factory
15951 SW 41st Street. Suite 400
Davie, FL 33331
Email: [email protected]
www.paitec.com
16