Sony Ericsson T28WORLD Owner Manual

Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Getting Started 3
AB
Contents
at a Glance
Preparing Your Phone for Use 4
Turning Your Phone On and Off 9
Display Information and Key Functions 11
Making and Receiving Calls 14
During a Call 17
Functions and Settings 19
Ericsson T28 WORLD
First edition (September 1999)
This manual is published by
Ericsson Mobile Communications AB,
without any warranty. Improvements and
changes to this manual necessitated by
typographical errors, inaccuracies of
current information, or improvements to
programs and/or equipment, may be made
by Ericsson Mobile Communications AB
at any time and without notice. Such
changes will, however, be incorporated into
new editions of this manual.
All rights reserved.
©Ericsson Mobile Communications AB,
1999
Publication number: AE/LZT 108 3026 R1A
Printed in Sweden
INNOVATRON PATENTS
T28 WORLD Features 20
Using the Menus 21
Your Personal Phone Book 27
Using the Call Log 35
Your Voice Mail Service 37
Personalizing Your Phone 39
Sending and Receiving Text
Messages (SMS) 46
Diverting Incoming Calls 56
Security for Your Phone and Subscription 58
Handling More than One Call Simultaneously 65
Setting Network Preferences 70
Knowing the Call Time/Call Cost 73
Using Two Voice Lines 75
Voice Control 76
Calling Card Calls 79
Sending and Receiving Fax and Data Calls 81
Extras 83
The Profile Concept 87
Accessories 90
Online Services 98
Additional Information 101
Quick Keys 102
Troubleshooting 104
Ericsson Mobile Internet 106
Technical Data 107
Glossary 108
Guidelines for Safe and Efficient Use 113
Limited Warranty 119
Declaration of Conformity 121
Index 123
Please note!
AB
Some of the services in this manual are not supported by all
networks. This also applies to the GSM International Emergency
Number 112 (or 911 in the Americas).
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Please contact your network operator or service provider if you are
in doubt whether you can use a particular service or not.
Note! You should read the Guidelines for Safe and Efficient Use
and the Limited Warranty chapters before using your
mobile phone.
Note! This manual is also available in multiple languages on a
CD-ROM that is part of the box contents you have received.
The
symbol on our products signifies that they have been
certified according to the EMC directive 89/336/EEC, the
Telecommunications directive 91/263/EEC, and the Low Voltage
directive 73/23/EEC when applicable. The products fulfil the
requirements according to the following standards:
Mobile Phones and Accessories in Combination:
ETS 300 342-1 EMC for European digital cellular
telecommunications.
Accessories Without Direct Connection to a Mobile Phone:
EN 50081 Electromagnetic compatibility, Generic Emission
Standard, and EN 50082 Electromagnetic compatibility,
Generic Immunity Standard.
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Getting Started
Preparing Your Phone for Use
4
Turning Your Phone On and Off
9
Display Information and Key Functions
11
Making and Receiving Calls
14
During a Call
17
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Preparing Your Phone
for Use
Overview
Front
Antenna
Indicator light
Volume key
Earpiece
Power On/Off
Display
Flip release button
Keypad
Microphone
Flip
Back
Connector for external antenna
Battery release catch
Battery
Hole for belt clip
Handsfree
connector
Flip release button
4
Preparing Your Phone for Use
Charging
connector
insert the SIM card
•
attach the battery to the phone
•
charge the battery
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
AB
Assembly
You need to do the following to use your phone:
The SIM Card
When you register as a subscriber with a network operator, you get a SIM
(Subscriber Identity Module) card. The SIM card contains a computer chip
that keeps track of your phone number, the services included in your
subscription, and your Phone Book information, among other things.
SIM cards come in two sizes. One is the size of a credit card and the other is
smaller. Your phone uses the smaller card. Many credit card-sized SIM cards
have a perforated smaller card that you can take out easily. Before you can use
your phone, you must insert the SIM card as shown below.
Inserting and Removing the SIM Card
2. Raise the edge of the SIM card
and slide it out.
1. Remove the battery if
attached. Slide the SIM card
into the slot, under the silver
colored holders, with the
golden connectors facing
down and the cut corner to
the right.
The PIN
Most SIM cards are supplied with a security code, also known as PIN
(Personal Identity Number), which you need to access the network.
Every time you turn on your phone, you are asked to enter your PIN. You will
find your PIN in the information from your operator.
Some operators may have services that require a second PIN, your PIN2.
You should be careful with your PIN, since it is your protection against
unauthorized use of your subscription.
Preparing Your Phone for Use
5
If your PIN is entered incorrectly three times in a row, the SIM card is
Unblocking Key code), which you also get from your operator.
The Battery
AB
blocked. If this happens, you can unlock it by using your PUK (Personal
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Your T28 WORLD comes with a lithium battery. The battery is not charged
when you buy your phone, but there may be enough power to switch the
phone on. We recommend that you charge the battery up to three hours before
you use the phone for the first time.
Attaching the Battery to Your Phone
•
Place the battery on the back of the phone and push until you hear a click.
When to Charge the Battery
The battery that comes with your phone can be charged whenever you wish
without affecting its performance. You can also charge the battery when the
phone is off.
To remind you that you will soon need to charge the battery or replace it with
a charged one:
•
an alarm signal (a short beep) sounds and the message Attention! Battery low
appears in the display
•
the indicator light on top of the phone starts flashing red
If you have an Ericsson-approved battery, you can check the remaining talk
and standby times in the Status menu by sliding the volume key upwards or
downwards in standby mode. You can move downwards in the menu by
pressing d. The remaining standby and talk times depend on the type of
battery you use and your position in the network. Please note that these times
are approximate and you may have 20% less time than is shown in the display.
Note! The phone turns itself off when the battery can no longer power it
satisfactorily.
6
Preparing Your Phone for Use
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Charging the Battery
1. Make sure that the battery is
attached to the phone.
2. Connect the charger to the
electrical outlet.
3. Connect the charger to the phone
as shown. The flash symbol on the
plug must face upwards.
Note! The electrical plug may look different depending on the electrical outlet
in your country. Do not connect it to any other item than your Ericsson Travel
Charger CTR-10. It must not be disconnected from the charger when plugged
into the electrical outlet.
To indicate charging:
•
the indicator on the top of the phone shows a steady red light (or green,
if the phone is switched on)
•
the message Charging only is shown in the display
•
the battery meter in the display pulses continuously
Note! If you charge a new battery that is empty, or a battery that has not been
used for a long time, it may take a while until you get an indication of
charging in the display.
An Ericsson-approved battery is indicated by Ericsson Optimized charging each
time you start charging the battery when the phone is switched on. For the best
charging, talk and standby times in the long run, we recommend that you use
only Ericsson-approved batteries with your phone.
Batteries that are not Ericsson-approved are charged slowly for safety reasons.
These are indicated by Charging alien battery each time you start charging the
battery when the phone is switched on.
Tip! You can use the phone while the battery is being charged. However, this
lengthens the charging time.
Preparing Your Phone for Use
7
the indicator on the top of the phone shows a steady green light.
Disconnecting the Charger
Disconnect the charger from the phone by
moving the plug upwards.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
AB
When the battery is fully charged, the battery meter in the display is full and
Removing the Battery
1. Slide the release catch upwards.
8
Preparing Your Phone for Use
2. Lift the battery away from
the phone.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Turning Your Phone On
and Off
Turning your Phone on
1. Open the flip by pressing the flip release button on the right side of
the phone.
2. Press and hold the N O key until you hear a tone.
If “PIN:” Appears in the Display
Some SIM cards are protected with a PIN code. If PIN: appears in the display
after you have turned on the phone:
1. Enter your PIN. If you make a mistake while entering your PIN, delete the
wrong number by pressing the C key.
2. Press Y E S .
Note! If your PIN is entered incorrectly three times in a row, the SIM card is
blocked. You can unblock it by using your PUK. See “The SIM Card Lock” on
page 58.
If Phone locked appears in the display, enter your phone lock code. See “The
Phone Lock” on page 59.
Network Search
After you have turned on the phone (and entered your PIN), the phone
searches for a network.
When a network is found, the phone beeps three times. The indicator light on
top of the phone flashes green once every second and your network operator’s
name (in most cases abbreviated) appears in the display.
This is called standby mode. You can now make and receive calls.
Note! See “Error Messages” on page 104, if you do not reach standby.
Initial Settings
The first time you turn on your phone, you may want to choose the ring signal
type and set the clock and date. For more information about these and other
Turning Your Phone On and Off
9
Display Language
AB
settings, see “Personalizing Your Phone” on page 39.
Most modern SIM cards automatically set the display language to the
language of the country where you bought your SIM card, (Automatic).
If this is not the case, the preset language is English (US). To change the display
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
language, see “Display Language” on page 43.
If your phone shows a language that you do not understand, you can change it
to Automatic, or English (US) , in the following ways:
To change the display language to Automatic
1. If not in standby mode, press and hold the N O key to go to standby.
2. Press the u arrow key.
3. Enter 8888.
4. Press the d arrow key.
To change the display language to English (US)
1. If not in standby mode, press and hold the N O key to go to standby.
2. Press the u arrow key.
3. Enter 0000.
4. Press the d arrow key.
Turning Your Phone Off
•
10
In standby mode, press and hold the N O key until you hear a tone.
Turning Your Phone On and Off
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Display Information and
Key Functions
In standby mode, the display shows the name of your operator, the time, the
signal strength and the battery power. Other icons appear if you receive any
messages, divert all your incoming calls, set the alarm clock and so on.
In this chapter, you will also learn about the key functions.
Display Information
The table below shows and explains each icon which may appear in standby.
Icon
Name
Explanation
Signal strength meter
Tells you the strength of the
network signal.
Battery meter
Tells you the status of the battery.
Missed call indicator
You have missed an incoming call.
Divert indicator
Accept Some/None
indicator
All incoming calls will be diverted to a
defined number.
No calls or only certain calls from
numbers in a list are received.
Profile indicator
Another profile than Normal has
been chosen.
Ring signal off indicator No sound can be heard when you
receive a call.
Alarm indicator
The alarm clock has been set
and is on.
Silent indicator
All audible signals are turned off,
except the alarm and timer.
SMS indicator
You have received a text message.
Voice mail indicator
You have received a voice message,
depending on your subscription.
Voice label in phone
indicator
Indicates that voice dialing is set to
Start on Open.
Line 1 indicator
Line 1 is in use for outgoing calls – if
you subscribe to the Two Line Service
Line 2 indicator
Line 2 is in use – if you subscribe to
the Two Line Service.
Display Information and Key Functions
11
Ciphering is currently not being
provided by the network.
Home zone indicator
You are in your home zone.
Does not appear on all networks.
AB
Ciphering indicator
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Note! Each menu has got its own symbol. See “Menu Graphics” on page 21.
Key Functions
The table below explains the key functions.
Key
Use
Flip release button To open the flip and answer incoming calls.
(To end a call, close the flip.)
12
YES
To make calls and answer calls.
To voice dial, press and hold the key.
To enter the Call Log from standby.
To choose a menu, sub-menu or setting.
NO
To turn the phone on or off, press and hold the key
in standby.
To end a call.
To reject a call.
To go back one level in the menus, to exit a setting or to
leave a setting unchanged.
To get back to standby mode, press and hold the key.
u and d
To enter the menu system.
To move (scroll) through menus, lists and text.
C (Clear)
To delete numbers and letters from the display.
To mute the microphone during a call, press and hold
down the key.
To set the phone silent, press and hold the key
from standby.
To delete an item from a list.
Number keys
To enter the digits 0-9.
The 0 key enters the international prefix (+) if held down.
To call your Voice Mail, press and hold the 1 key.
To enter the phone book, press and hold any of the
numbers 2-9.
To move through menus using shortcuts.
To enter letters, for example when writing an SMS.
*
To enter *.
To shift between upper- and lower-case letters.
Display Information and Key Functions
Use
# (Hash)
To enter #.
Volume key
upwards and
downwards
To increase or decrease the volume of the earpiece or
handsfree loudspeaker during a call.
To reject an incoming call, quickly slide the key twice.
To voice dial, slide and hold the key when the flip is open
To move through the menus.
To open the flip without answering a call, slide and hold
the key while pressing the flip release button.
To enter the Status menu.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Key
Note! For information about the key functions in the menus, see “Moving
through the Menus” on page 23.
Display Information and Key Functions
13
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Making and
Receiving Calls
In this chapter, we assume that you have turned on your phone and that you
are within range of a network. If you are abroad, you may use other networks,
provided your home network has an agreement that allows you to do this.
See “Setting Network Preferences” on page 70.
Making a Call
1. Open the flip by pressing
the flip release button.
2. Enter the area code and
phone number.
3. Press Y E S .
Note! Some countries may not use area codes.
While a call is in progress, a time counter automatically starts and you can see
how long you have been on the phone. If your network and subscription
supports it, you see the cost of the call in the display. See “Knowing the Call
Time/Call Cost” on page 73.
Ending a Call
•
Close the flip or press N O to end the call.
Redialing a Previously Called Number
In the Call log you find numbers that you have dialed, answered or missed.
To redial a previously called number
1. Press Y E S to enter the Call log.
2. Press u or d to choose the number you want to call.
3. Press Y E S to make the call.
For more information, see “Using the Call Log” on page 35.
14
Making and Receiving Calls
Automatic Redialing
AB
If the connection failed when you first called and the display shows Retry?,
User busy
Retry?
you can redial the number by pressing Y E S . Your phone automatically redials
(up to 10 times)
•
until the call is answered. When the call is successfully connected, you
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
hear a ring signal.
•
until you press a key or receive a call.
Note! You do not need to take the phone to your ear until you hear the
ring signal.
Automatic redialing is not available for fax and data calls.
Making International Calls
1. Press and hold the 0 key until a + sign appears.
The + replaces the international prefix number of the country from which
you are calling.
2. Enter the country code, area code (without the leading zero) and
phone number.
3. Press Y E S .
Making Emergency Calls
1. Enter 112(the international emergency number, or in the Americas 911).
2. Press Y E S .
The international emergency number 112 (or 911) can normally be used in any
country, with or without a SIM card inserted, if a GSM network is within range.
Note! Some network operators may require that a SIM card is inserted, and in
some cases that the PIN code has been entered as well.
Some networks may not use the international emergency number 112 (or 911).
911 can also be used in areas that use 112 as the international emergency
number, and vice versa.
Receiving a Call
When you receive a call, the phone rings and the display shows Answer?
If your subscription includes the Calling Line Identification (CLI) service and
the caller’s network sends the number, you see the caller’s number in the
display. If the caller’s number and name are stored in the phone book, the
caller’s name is also shown.
If the incoming call is a restricted number, the display shows Withheld. If the
incoming call is a number without any CLI service, Unknown is shown.
Making and Receiving Calls
15
•
Open the flip by pressing
the flip release button
or press Y E S if the flip
AB
Answering a Call
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
is open.
Rejecting a Call
•
Busy signal
Slide the volume key on the side of the phone twice.
The display shows Busy signal. The caller hears a busy signal if this is
supported by the caller’s subscription. If Divert When Busy is on, the call
is diverted to the number you have specified. See “Diverting Incoming
Calls” on page 56.
Note! To open the flip without answering a call, you need to slide the volume
key while opening the flip. Then you may reject a call by pressing N O or by
closing the flip.
Ciphering
Ciphering is a built-in feature that scrambles your calls and messages to
provide additional privacy.
An exclamation mark is shown in the display to indicate that ciphering is
currently not being provided by the network.
16
Making and Receiving Calls
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
During a Call
Your phone has several functions, which you might find helpful while a call is
in progress.
Changing the Listening Volume
You can easily change the listening volume during a call by sliding the
volume key on the side of the phone.
To change the listening volume during a call
•
Slide upwards to increase the volume.
•
Slide downwards to decrease the volume.
Muting the Microphone
If you wish, you may turn the microphone off during a call.
To turn the microphone off temporarily during a call
1. Press and hold down the C key.
Muted
Muted appears in the display.
2. To continue your conversation, release the C key.
Tip! Instead of pressing and holding the C key, you can put the call on hold.
To put a call on hold
1. Press Y E S .
Call on hold
Call on hold appears in the display.
2. To continue your conversation, press Y E S again.
Sending Tone Signals
To use telephone banking services or to control an answering machine, you
need to use codes. These codes are sent as tone signals (also known as DTMF
tones or touch tones). With your mobile phone, you may use these codes
during a call. If you press 0-9, * and # during a call, these numbers and
characters are sent as tone signals.
Tip! You can also save codes only or codes together with a phone number in
your Phone Book. See “Telephone Banking Services” on page 32. However, it
may be a risk to save your codes in the phone in case it is stolen.
During a Call
17
AB
The Notepad
If you want to make a note of a phone number during a call, you can use your
phone display as a notepad.
To use the notepad during a call
Use the number keys to enter the number.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
When you end the call, the number remains in the display or, if Ask to Save is
on, you will be asked to save the number in your phone book. You can also
find the number in Add Number in the Phone Book menu. See “Your
Personal Phone Book” on page 27.
When you enter the number, the person you are talking to will hear the tones.
If you wish, you may turn the tones off during a call. See “Scratchpad” on
page 42.
Checking the Duration or Cost of the Call
During a call, the display normally shows the duration in minutes and
seconds. Depending on your subscription, you may see the call cost
displayed instead.
Note! This depends on your network and SIM subscription. See “Knowing the
Call Time/Call Cost” on page 73.
Minute Minder
If you turn on the minute minder, you hear a beep once every minute during a
call as a reminder of the duration of the ongoing call. See “Minute Minder” on
page 42.
More than One Call Simultaneously
Your phone is capable of handling more than one call simultaneously. You can
put the current call on hold and then make or answer a second call. You can
also set up a conference call with up to five people. See “Handling More than
One Call Simultaneously” on page 65.
18
During a Call
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Functions and Settings
T28 WORLD Features
20
Using the Menus
21
Your Personal Phone Book
27
Using the Call Log
35
Your Voice Mail Service
37
Personalizing Your Phone
39
Sending and Receiving Text Messages (SMS)
46
Diverting Incoming Calls
56
Security for Your Phone and Subscription
58
Handling More than One Call Simultaneously
65
Setting Network Preferences
70
Knowing the Call Time/Call Cost
73
Using Two Voice Lines
75
Voice Control
76
Calling Card Calls
79
Sending and Receiving Fax and Data Calls
81
Extras
83
The Profile Concept
87
Accessories
90
Online Services
98
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
T28 WORLD Features
Your T28 WORLD is a small new generation phone: a Dual Band
(GSM900/1900) phone with a lithium battery; a phone of modern design
and advanced technology.
The active flip makes it possible for you to answer by just opening the flip.
Or why not use the Voice Control and say ‘Answer’ to answer a call or ‘Busy’
if you wish to reject the call. You can also call a person by simply saying
the name.
The T28 WORLD has a ‘Profile’ feature which makes it possible for you to
change a few settings by just choosing a certain Profile, since each profile
includes a group of settings preset to suit a certain environment. For example,
when you go to a meeting, you can just choose the ‘Meeting’ profile and a
number of settings that suit a meeting are then set automatically.
The Profiles are also related to intelligent accessories such as a desktop
charger, a portable or vehicle handsfree. For example, you may place the T28
WORLD in a vehicle handsfree kit and the ‘In Car’ profile is chosen
automatically.
In the display of the T28 WORLD you can see a mixture of text and symbols,
which makes it easier for you to move through the menus when you want to
change a certain setting, turn on the Vibrate Mode, send a message, save a
number and so on.
An extra feature is the numbered shortcuts, which takes you to a certain
setting quickly and easily. You may also create your own favorite menu,
‘My Shortcuts’, by including the settings you use most often. If you should
need help using the menus, the T28 WORLD is equipped with help texts to
guide you.
20
T28 WORLD Features
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Using the Menus
You can find all your phone functions in the menus. You use the menus every
time you want to change a setting in your phone, such as the ring signal.
You also use the menus to get the most out of your phone: to set the alarm
clock, send text messages, save important phone numbers, etc.
The menus are arranged in a loop, which you enter and move (scroll) through
with the u and d keys or by using shortcuts. Each menu contains a list
of options. Some menus have sub-menus with additional options.
Menu Graphics
You enter the menus by pressing u or d. At the top of the display, there
are icons symbolizing each menu. Besides these, there are symbols within the
sub-menus indicating missed calls, help texts, voice labels etc.
The table below illustrates and explains each menu icon and symbol.
Symbol
Name
Description
Phone Book menu
Your personal phone book.
Messages menu
Handling of text and voice messages.
Call Info menu
Call time and call cost information.
Settings menu
Personal settings and profiles.
Extras menu
Games, alarm clock and other extras.
Call Handling menu
Handling of ongoing calls.
My Shortcuts menu
A selection of your most frequently used
functions.
Ongoing call
indicator
You have an ongoing call.
Missed calls indicator Indicates a missed call in the Call Log,
in the missed calls list and in standby.
Answered call
indicator
Indicates an answered call in the Call Log.
Dialed number
indicator
Indicates a dialed number in the Call Log.
Phone memory
indicator
Indicates that a phone book entry is
saved in the phone memory and the SIM
memory is full.
Using the Menus
21
Description
Group indicator
Indicates that a phone book entry
is a group.
Unread SMS
indicator
Indicates that a text message has not
been read.
Unchecked Voice
Mail
Indicates that a voice message has not
been checked.
Phone book look up
indicator
Indicates that you can enter the phone
book by pressing u.
SIM card memory
indicator
Indicates that a phone book entry is
saved in the SIM card memory.
AB
Name
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Symbol
Voice label in phone Indicates that a voice label has been
indicator
recorded for an entry in the phone only.
Indicates that voice dialing is set to Start
on Open.
Voice label in car
indicator
Indicates that a voice label has been
recorded for an entry in the car
handsfree kit.
Voice label in phone Indicates that a voice label has been
and in car indicator recorded for an entry in the phone and in
the car handsfree kit.
Preferred network
indicator
Indicates that a network is preferred and
can be used.
Forbidden network
indicator
Indicates that a network is forbidden and
cannot be used.
Home zone indicator Indicates that you are in your home zone.
Does not appear on all networks.
22
Using the Menus
Help text indicator
Indicates a help text.
Lock indicator
Indicates that the card lock or
phone lock is on.
AB
Moving through the Menus
There are two ways of moving through the menus:
•
scrolling with u or d
•
using shortcuts
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Scrolling by Using u or d
Press...
to...
U
scroll left or up through menus or functions.
D
scroll right or down through menus or functions.
YES
select a menu, sub-menu or setting.
NO
go back one level in the menu system, exit a setting or
leave a setting unchanged.
go back to standby mode by pressing and holding
the key.
C
delete an item from a list.
Note! For information about how to enter letters, see “Entering Letters” on
page 28.
Tip! Once in the menu system, you can press and hold the u or d key or
slide and hold the volume key until you reach the menu or sub-menu that you
want instead of pressing the u or d key repeatedly.
Using Shortcuts
A quicker way to move through the menus is to use the shortcuts. You simply
enter the number of the menu or sub-menu to which you want to go, but you
first need to enter the menus by pressing u or d. To get back to standby,
you press and hold N O as normal.
Tip! A quicker way to enter the Find and Call function is to press and hold
d. A quicker way to enter the first sub-menu in the My Shortcuts menu is
to press and hold u.
Note! Your phone may not have all the menu alternatives described in this
manual since many of them are network- and subscription-dependent.
Because of this, the shortcut numbers may vary between phones.
How To Interpret the Instructions
In the instructions in this manual we use the u and d keys to describe
the functions and settings, since the shortcut numbers may vary between
phones due to your subscription and network.
The following instruction tells you how to set the key sound to ‘Tone’.
Using the Menus
23
2. Select Tone.
Interpret the instruction as follows:
AB
To set the key sound
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Key Sound, Y E S .
1. From the standby mode, use d or u to scroll to the Settings menu.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Press Y E S to select the menu.
Now you are in the Settings menu.
The name of the menu that you have chosen is shown at the top of the
display (Settings).
3. Press Y E S to select the Sounds & Alerts sub-menu.
(You do not need to scroll with the arrow keys since this is the first
sub-menu in the main menu Settings).
4. Use d or u to scroll to the Key Sound sub-menu.
Press Y E S to select the sub-menu.
5. Use d or u to scroll to Tone.
Press Y E S to select the Tone alternative.
Now you have set the key sound to ‘Tone’.
To go back to standby mode, press and hold the N O key.
This is how to interpret the same instruction as above when using shortcuts:
To set the key sound
1. Press d or u to enter the menu system.
2. Press 4 to select the Settings menu.
3. Press 1 to select the Sounds & Alerts sub-menu.
4. Press 5 to select the Key Sound sub-menu.
5. Select Tone.
Display Text
When you move through the menu system, the display changes. The following
hints can help you:
•
Black text within a frame at the top indicates the menu you have chosen.
•
Inverted text on a black layer indicates your position in the menu system.
•
Gray text indicates a function that is temporarily unavailable, for example
If you press Y E S you enter this menu or select this setting.
due to your subscription or due to a certain setting which is not on.
•
Text marked with a check indicates the current setting or settings selected.
•
Text marked with a filled button indicates the current setting selected.
Note! Most sub-menus in the Call Handling menu are shown in gray text
when no call is active. However, they are shown in black text during a call.
24
Using the Menus
AB
My Shortcuts
You can place your favorite settings in the menu My Shortcuts. In this way,
you can quickly and easily reach the settings you use most.
When you buy your phone, My Shortcuts contains a few settings which you
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
can remove if you wish. You can also add a setting from another menu to
My Shortcuts.
To add a setting to My Shortcuts
1. Scroll to My Shortcuts, Y E S , Edit Shortcuts, Y E S .
2. Select a setting from the list by pressing *.
3. Enter the position number you want for your setting in this menu.
4. Press Y E S .
If you want to add another setting, repeat steps 2 and 3.
To remove a setting from My Shortcuts, repeat steps 1 and 2.
5. Press Y E S to exit the list.
Tip! A quicker way to enter the first sub-menu in the My Shortcuts menu is to
press and hold u.
Help texts
To help you use the functions and settings of the menus, your phone includes
pop-up help texts that explain the sub-menus.
These help texts are set to On when you buy your phone, but you may turn
them off at any time.
To turn the help texts on or off
1. Scroll to Settings, Y E S , Display, Y E S , Help Functions, Y E S , Menu Help, Y E S .
2. Select On or Off.
Using the Menus
25
Find and Call
Find and Send*
Add Number
Find and Edit
Voice Labels
Delete All
Groups
Email Addresses
Calling Cards
Options
Memory Status
Fixed Numbers
Info Numbers
ServiceNumbers
Using the Menus
Switch to Line 1
Next Incoming
Enable Caller ID
Disable Caller ID
Scratchpad*
Hold Call*
Switch Calls*
Release Active*
Retrieve Call*
Join Calls*
Transfer Call*
Extract Part*
Release All*
Select Profile
Ring Volume
Switch to Line 1
Edit Shortcuts
English texts.
* Only available during a call.
AB
are network- and subscription-dependent.
Alarm Clock
Timer
Stopwatch
Calculator
Games
Accessories
Please note that many of the menu alternatives
Sounds & Alerts
Profiles
Call Options
Networks
Display
Language
Time and Date
Locks
Voice Control
Handsfree
Master Reset
The English display texts may differ from the US
Missed Calls
Call Log
Last Call
Credit
Total Cost
Price
Total Time
Outgoing Time
Clear Call Log
Reset Counters
Options
Note! The default display language is English.
Call Voicemail
Inbox
Send New
Unsent
Templates
Sent Items
Options
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
26
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Your Personal
Phone Book
You can create a personal phone book by saving phone numbers and
accompanying names (an entry). An easy way to make calls is by recalling the
phone numbers or names saved in your phone book.
Creating a Personal Phone Book
Before you start creating your personal phone book, there are a few things you
need to know. You need to learn about the memories, how to save the numbers
with the international (+) sign and how to enter letters.
Phone Book Memories
You can save phone numbers and names in:
•
the card memory on the SIM card
•
the phone memory
Your entries are first saved in the positions on your SIM card. The actual
number of memory positions available depends on your SIM card.
Saving your numbers in the card memory allows you to use the numbers
saved on the SIM card even when you change phones, i.e. when you insert
your SIM card into another phone.
By saving your numbers in the phone memory, they are always available to
you in your phone, even if you change SIM cards. The phone memory holds
99 positions in which your entries are saved when all SIM positions are used.
International Numbers
If you intend to use your phone both at home and abroad, it is a good idea to
save all phone numbers as international phone numbers, i.e. with the (+) sign,
(which automatically replaces the international dialing prefix for the country
you are calling from) followed by the country code, the area code and the
phone number.
Your Personal Phone Book
27
Press and hold 0 to enter the + sign.
Exclude the leading zero in the area code.
Entering Letters
AB
To enter an international phone number
•
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
You can enter letters when you use the phone book and when you compose a
short message (SMS). See “Sending and Receiving Text Messages (SMS)” on
page 46.
Press the appropriate key, 1–9, 0 or #, repeatedly until the character you want
appears in the display.
Press…
to get…
1
Space - ? ! ‚ . : ; " ’ < = > ( ) _ 1
2
ABCÅÄÆàÇ2Γ
3
DEFèÉ3∆Φ
4
GHIì4
5
JKL5Λ
6
MNOÑÖØò6
7
PQRSß7ΠΣ
8
TUVÜù8
9
WXYZ9
0
+&@/¤%$£¥§¿¡0Θ Ξ Ψ Ω
#
#*↵
Example:
•
To enter an ‘A’, press 2 once.
•
To enter a ‘B’, quickly press 2 twice.
•
To enter lower-case letters, enter the letter, for example an ‘A’,
and then press *. An ‘a’ appears. Lower-case letters now appear
until you press * again.
•
To enter numbers, press and hold any number key.
•
To delete letters and numbers, press the C key.
You may also use the volume key as a shortcut to certain letters:
•
To enter a ‘B’, slide the volume key upwards and press 2.
•
To enter a ‘C’, slide the volume key downwards and press 2.
Tip! You can choose another alphabet by pressing and holding #.
28
Your Personal Phone Book
AB
Saving a Number Together with a Name
Every phone number that you save gets a position number. You can save the
phone numbers together with a name to make it easier for you to keep track of
your phone numbers.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To save a number together with a name
1. Scroll to Phone Book, Y E S , Add Number, Y E S .
A list of numbers used but not saved appears.
2. Select Add New? or any of the numbers from the list by pressing Y E S .
3. Enter a phone number that you wish to save (including the (+) sign and the
country code) and press Y E S .
4. Enter a name that you want to link with the phone number and press Y E S .
5. You now have three options:
•
•
To save the number in the suggested first empty position, press Y E S .
To save the number in another position, press C to delete the position
number, enter a new position number and press Y E S .
•
To save the number in the phone memory, you need to know how many
positions you have got on your SIM card. You can check this in
Memory Status in the Phone Book menu. If, for example, you have
200 positions on your SIM, you can enter position number 201 to save
a number in the phone memory.
If you have turned Voice Dialing on, you are asked if you want to add a voice
label to your phone book entry. See “Voice Control” on page 76.
Ask to Save
If you wish to be asked to save any dialed or answered number that is not
already saved in your phone book, you can turn on the Ask to Save option.
To turn the Ask to Save function on or off
1. Scroll to Settings, Y E S , Display, Y E S , Help Functions, Y E S , Ask to Save, Y E S .
2. Select On or Off.
Note! Your subscription must support the Calling Line Identification service.
Calling a Number Saved In the Phone Book
You can either call a number by using the name saved with it or you can call
the number by using the position number that it was saved in.
The order of searching for names and numbers depends on the sort order you
have chosen, i.e. alphabetically or by position.
Your Personal Phone Book
29
2. Select a sort order.
To call a number saved in the phone book
1. Scroll to Phone Book, Y E S , Find and Call, Y E S .
AB
To choose a sort order
1. Scroll to Phone Book, Y E S , Options, Y E S , Sort Order, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Enter the position number or the name (or the first few letters of the name)
linked with the number that you want to call.
3. Press Y E S .
If the name displayed is not the one you want, press u or d until you
find the correct name and number.
4. Press Y E S to make the call.
Tip! A quicker way to enter the Find and Call function is to press
and hold d.
Shortcuts to Phone Book Entries
When in standby, you can find an entry by:
•
entering the position number followed by # .
•
pressing and holding one of the keys 2-9 to find an entry beginning with a
specific letter.
For example, pressing and holding 2 takes you to the first entry beginning
with the letter A (or closest following).
Once you are in the list of phone book entries you can use u or d to
scroll through the positions, or enter a position number or a letter to go to a
certain entry.
Speed Dialing
You can call the phone numbers that you have saved in positions 1–9 in the
memory by entering the position number and then pressing Y E S .
Example:
1. Enter the number 3.
2. Press Y E S to make the call.
Keeping the Phone Book Up to Date
You may need to change the names and numbers in the phone book from time
to time. You may also want to change the position number of an entry.
Editing a Phone Number In the Phone Book
You need to find the phone book entry that you wish to edit. You can use
either the stored position or the name. See “Calling a Number Saved In the
Phone Book” on page 29.
30
Your Personal Phone Book
AB
To edit an entry
1. Scroll to Phone Book, Y E S , Find and Edit, Y E S .
2. Enter the position number or the name of the entry that you wish to edit.
Press Y E S .
If the name displayed is not the one you want, press u or d until you
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
find the correct name and number.
3. Press Y E S to select the entry.
4. Select Edit.
5. Edit the number and press Y E S .
Use the u or d keys to move the cursor. Use the C key to delete.
6. Edit the name and press Y E S .
7. Edit the position number and press Y E S .
Overwrite Protection
If you try to save a phone number in a position which already contains a
phone number, the message Replace? appears together with the name saved in
that position. You now have two options:
To save the number in the selected position
•
Press Y E S to replace the number with the new one.
To save the number in a different position
1. Press N O .
2. Enter the new position number.
3. Press Y E S to save the number in the new position.
When the Card Memory Is Full
When all SIM card positions are full, an icon appears next to the position
number, see margin. From now on your entries are stored in the
phone memory.
If all positions, including the phone memory are full, you have to delete an old
number by entering a position that is already used and press Y E S .
To delete an entry from the memory
1. Scroll to Phone Book, Y E S , Find and Edit, Y E S .
2. Enter the position number or the name of the number that you want to
delete and press Y E S . (This depends on the sort order, i.e. alphabetically
or by position.)
3. Press Y E S .
4. Select Delete.
5. Press Y E S to confirm your choice.
Your Personal Phone Book
31
2. The question Delete all in phone memory? appears.
Delete all in
phone memory?
Press Y E S .
AB
To delete all entries from the phone memory
1. Scroll to Phone Book, Y E S , Delete All, Y E S .
3. Enter the phone lock code (0000 or another one that you have chosen
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
yourself).
All entries in the phone memory are deleted.
Telephone Banking Services
If you use telephone banking services, you can save the phone number of your
banking service together with your personal codes, or you can save your codes
only. You need to add a pause (p) between the phone number and the codes.
You insert a pause by pressing and holding the * key. Usually, a # is required
after each code. Sometimes a pause is required, too. Talk to your bank if you
are in doubt about how to use # and pause (p).
Note! It may be a risk to save your codes in the phone in case it is stolen.
To save a phone number with codes
1. Scroll to Phone Book, Y E S , Add Number, Y E S , Add new?, Y E S .
2. After entering the phone number, press and hold the * key until the pause
character p appears in the display.
3. Enter the code and #. If required, enter a pause, the next code and so on.
4. Enter the name that you want to link with the phone number and code and
press Y E S .
5. Press Y E S to save.
If you want to save the number in a different position than the one
suggested, see “Saving a Number Together with a Name” on page 29.
To make a call with tone signal codes, proceed as described in “Calling a
Number Saved In the Phone Book” on page 29. When you make the call, the
phone dials the number, waits until the call is answered and then sends the
code. If you insert another pause and another code, it pauses again, sends the
next code and so on.
To save codes only
1. Scroll to Phone Book, Y E S , Add Number, Y E S , Add new?, Y E S .
2. Enter the code followed by a # and if required, a pause, another code and
so on.
3. Press Y E S .
4. Enter a name that you want to link with your codes and press Y E S .
5. Press Y E S to save.
32
Your Personal Phone Book
To send the codes during a call
1. Scroll to Phone Book, Y E S , Find and Send, Y E S .
AB
During a call, you can retrieve these codes from the phone book and send them.
2. Enter the name (or first few letters) or position number of your codes and
press Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
3. Press Y E S to send the codes.
Groups
The T28 WORLD allows you to create groups of phone book entries.
In this way you can send a text message to several recipients at the same time.
See “Sending and Receiving Text Messages (SMS)” on page 46.
To create a new group
1. Scroll to Phone Book, Y E S , Groups, Y E S , Add new?, Y E S .
2. Enter a name for the group and press Y E S .
3. Scroll to Add new?, Y E S .
4. Select an entry in your phone book.
5. To add the next member, press Y E S at Add new?.
To add a new member to an existing group
1. Scroll to Phone Book, Y E S , Groups, Y E S .
2. Select the group that you want to edit.
3. Scroll to Edit, Y E S , Add new?, Y E S .
4. Select an entry in your phone book.
To delete a member from a group
1. Scroll to Phone Book, Y E S , Groups, Y E S .
2. Select the group that you want to edit.
3. Select Edit.
4. Scroll to the member that you want to delete and press C .
5. Press Y E S to confirm your choice.
To delete a group
1. Scroll to Phone Book, Y E S , Groups, Y E S .
2. Select the group that you want to delete.
3. Select Delete.
4. Press Y E S to confirm your choice.
E-mail addresses
You can save e-mail addresses to be used when you want to send a text
message as an e-mail. See “Sending and Receiving Text Messages (SMS)” on
page 46. You can save 10 e-mail addresses, each consisting of 60 characters.
Your Personal Phone Book
33
To save an e-mail address
2. Enter an e-mail address and press Y E S .
3. Enter a name and press Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Tip! The @ sign is accessed by pressing the 0 key three times.
AB
1. Scroll to Phone Book, Y E S , Email Addresses, Y E S , Add new?, Y E S .
To edit an e-mail address
1. Scroll to Phone Book, Y E S , Email Addresses, Y E S .
2. Select the entry that you want to edit.
3. Select Edit.
4. Edit the e-mail address and press Y E S .
5. Edit the name and press Y E S .
To delete an e-mail address
1. Scroll to Phone Book, Y E S , Email Addresses, Y E S .
2. Select the entry that you want to delete.
3. Select Delete.
4. Press Y E S to confirm your choice.
Checking the Status of the Memories
The Memory Status function in your phone book lets you check how many
memory positions you have left in your memories.
To check the status of your different phone book memories
1. Scroll to Phone Book, Y E S , Memory Status, Y E S .
2. Use u or d to scroll through the list.
34
Your Personal Phone Book
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Using the Call Log
The Call Log is a phone number log that saves information (time, date, phone
number and name) about the last 30 incoming and outgoing calls. Once your
list exceeds 30 calls, the oldest one is deleted.
What Calls Are Saved?
The numbers that you have dialed are always saved. If your subscription
includes the Calling Line Identification (CLI) service and the caller’s network
sends the number, you will also find the numbers (together with a name if
saved in your phone book) of answered and missed calls in the Call Log.
If the incoming call is a restricted number, the display shows Withheld.
If the incoming call is a number without any CLI service, Unknown is shown.
You can call any of the numbers in the Call Log.
The Call Log saves:
Dialed numbers
Answered calls
Missed calls
All the calls are saved together in chronological order. The last call you have
made is saved in the first position. If the same number is called more than
once, the latest call replaces earlier ones. If you check a call within 24 hours,
the time of the call is displayed. Otherwise, the time is replaced by the date.
Note! If you change SIM cards or turn the Call Log off, the list is cleared.
Called numbers may remain in the SIM card memory though.
To call a number from the Call Log
1. Scroll to Call Info, Y E S , Call Log, Y E S .
2. Scroll to the number that you want to call and press Y E S .
Tip! Press Y E S when the phone is in standby mode to go directly to the
Call Log.
Using the Call Log
35
2. Scroll to the number you want to delete and press C .
The question Delete? appears in the display.
3. Press Y E S to delete the number.
AB
To delete a number from the Call Log
1. Scroll to Call Info, Y E S , Call Log, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To clear the Call Log
1. Scroll to Call Info, Y E S , Clear Call Log, Y E S .
The question Call Log Clear? appears in the display.
2. Press Y E S to clear the Call Log.
To turn the Call Log on or off
1. Scroll to Call Info, Y E S , Options, Y E S , Set Call Log, Y E S .
2. Select On or Off.
If you select Off the question Call Log Clear? appears in the display.
3. Press Y E S to clear the Call Log.
Missed Calls
If you have missed a call, the message Missed Calls: 1 appears in standby mode,
Missed calls: 1
where the number 1 indicates the number of missed calls.
1. Press Y E S to display the missed calls.
2. If you wish to call a number from the Missed Calls List, press Y E S at the
number you want to call.
Note! You can also see the Missed Calls List in the Call Info menu.
Missed calls are also saved in the Call Log.
To be able to see if you have missed a call, the Call Log must be on.
Showing And Hiding Your Number
Some operators offer subscriptions where your phone number is normally
hidden. You can choose to show or hide your number for a particular call,
if Calling Line Identification Restriction service (CLIR) is supported by your
subscription.
To hide your phone number for a particular call
1. Enter the phone number you wish to call.
2. Scroll to Call Handling, Y E S , Disable caller ID, Y E S .
3. Press Y E S to make the call.
To show your phone number for a particular call
1. Enter the phone number you wish to call.
2. Scroll to Call Handling, Y E S , Enable caller ID, Y E S .
3. Press Y E S to make the call.
36
Using the Call Log
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Your Voice Mail Service
Note! This service depends on your subscription and operator.
The answering service of your network allows callers to leave a voice
message when you cannot answer your calls. Depending on your network
operator, you will be informed that you have received a voice message in
different ways.
Some operators inform you by sending a specific Voice Mail indication.
If this is the case, the voice mail icon appears in the display.
Most operators, however, inform you by sending a text message, (i.e. an
SMS), for example asking you to call your Voice Mail Service. For more
information about receiving and reading text messages, see “Receiving a
Message” on page 50.
Note! For more information about your Voice Mail Service, please refer to the
information provided by your network operator.
Communicating With Your Voice Mail Service
If you want your phone to easily interact with your Voice Mail Service, you
can store the number to your Voice Mail Service. You will get the number in
the information provided by your network operator.
To store your Voice Mail number
1. Scroll to Messages, Y E S , Options, Y E S , Voice Mail No., Y E S .
2. Enter your Voice Mail number and press Y E S .
Note! The number to your Voice Mail Service may be different if you are
calling from a network that is not your home network.
Calling your Voice Mail
When you receive a voice mail, an alert signal sounds and the message
New voicemail appears in the display (only if you receive the specific voice mail
indication). If you want to check your voice mail now, press Y E S to call your
Voice Mail Service.
If you press N O , you can call your Voice Mail Service at a later time to listen
to your recorded messages.
Your Voice Mail Service
37
Scroll to Messages, Y E S , Call Voicemail, Y E S .
AB
To call your Voice Mail Service
•
Tip! You can also call your Voice Mail Service by pressing and holding 1
from standby.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Changing Number and Signal
To change your Voice Mail number
1. Scroll to Messages, Y E S , Options, Y E S , Voice Mail No., Y E S .
2. Press and hold C to delete the existing number.
3. Enter your new Voice Mail number and press Y E S .
To change the message alert signal
1. Scroll to Messages, Y E S , Options, Y E S , Message Alert, Y E S .
2. Select the signal you want.
Tip! If you subscribe to the Two Line Service, you may have different Voice
Mail numbers for your two lines. You may also set different options for the two
lines. For example, you can set all incoming calls on Line 1 to be diverted to
your Voice Mail and let all incoming calls on Line 2 be connected.
Further information about your Voice Mail Service can be found in the
operating instructions supplied by your network operator.
38
Your Voice Mail Service
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Personalizing Your Phone
Silent
You can choose to set your phone completely silent so that all signals except
the alarm and timer signals are turned off.
To set the phone silent
1. From standby, press and hold C .
2. Silent on? appears. Press Y E S .
An icon appears in standby.
To cancel, repeat step 1 and press Y E S at Silent off?.
Ring Signal Volume
You can set the volume in six steps. The first step means that two clicks
are heard when you receive a call. You can also turn the ring signal off (0).
An icon then appears in standby.
To set the ring signal volume
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Volume, Y E S .
The level of the ring volume appears in the display.
2. Use u to increase the volume, d to decrease it.
The phone rings once with the actual setting as you increase the volume.
3. Press Y E S to save the setting.
Tip! Use the volume key on the side of the phone to change the volume of the
ring signal silently.
Increasing Ring
You can choose a ring signal that rises in steps from the softest volume to the
loudest, Increasing Ring.
To set the ring signal to Increasing Ring
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Increasing Ring, Y E S .
2. Select On.
The Increasing Ring must be Off for the ring signal volume to apply.
Note! If the phone is set to silent, the increasing ring signal is not heard.
Personalizing Your Phone
39
AB
Ring Signal Type
You can choose a ring signal from a list of different sounds and melodies.
You can also compose up to four melodies of your own by entering notes with
the keypad. See “Composing Ring Signals” on page 41.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To choose one of the ring signal types
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S ,
Voice Calls, Y E S .
2. Select the ring signal type that you want.
Tip! If you do not wish to disturb other people, use the volume key on the side
of the phone to scroll silently.
Different Ring Signals for Line 1 and Line 2
If you subscribe to the Two Line Service, you can set different ring signals for
the two lines. L1 and L2 are displayed instead of Voice.
Different Ring Signals for Voice, Data and Fax Calls
Provided your SIM subscription supports Fax and Data calls, you can set
different ring signals for voice, fax and data calls respectively.
Specific Ring Signals for Personal Calls
If your subscription includes the Calling Line Identification (CLI) service,
you can assign a personal ring signal to up to ten callers. You can, for
example, have one ring signal for your friend and another one for your
colleague.
If the last seven digits of a caller’s number correspond to a number you have
specified, then that caller’s ring signal is used.
You can include question marks (?) in a phone number. For example,
012345??? means that calls from phone numbers between 012345000 and
012345999 will have the same personal ring signal. You get a question mark
by pressing and holding #.
To specify a caller’s number and the accompanying ring signal
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S , Personal Rings,
Y E S , Add new?, Y E S .
2. Enter the caller’s number and press Y E S .
You can also recall it from the Phone Book by pressing u.
3. Select the ring signal type you want.
40
Personalizing Your Phone
To delete a caller’s number
Personal Rings, Y E S .
2. Scroll to the number you wish to delete and press Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
3. Select Delete.
AB
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S ,
Composing Ring Signals
You can compose four different ring signals.
To compose a ring signal
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S ,
Custom rings, Y E S .
2. Select My ring 1, My ring 2, My ring 3 or My ring 4.
3. Press C to clear the display.
4. Use the keypad to enter notes.
The keypad now works as a keyboard (see figure in margin above):
•
B
Press and hold a key to enter a long note.
•
Press 0 to raise the note one octave.
•
Press # once to raise the note one half-tone.
•
Press # twice to lower the note one semitone.
5. To listen to your melody, press Y E S .
6. Press Y E S again to save it or press N O to continue editing.
Vibrate Mode
You can choose to be notified of an incoming call by the buzzing of the
Vibrate Mode. You can set the phone’s Vibrate Mode to one of the following:
•
On (all the time)
•
On If Silent (on when the ring volume is turned off or when you have set
the phone to silent)
•
Off (all the time)
Note! When your phone is placed in a desktop charger or a handsfree car kit,
the Vibrate Mode is turned off automatically.
To set the Vibrate Mode
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Vibrate Mode, Y E S .
2. Select the setting you want.
Personalizing Your Phone
41
AB
Message Signal
You can choose whether to hear clicks, tones or nothing (silent) when you
receive a voice or text message (SMS).
To set the message signal
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S ,
Message Alert, Y E S .
2. Select the signal you want.
You can also find the Message Alert in Options in the Messages menu.
Alarm Signal
To change the alarm signal for the alarm clock
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Ring Signals, Y E S ,
Alarm Signal, Y E S .
2. Select the signal you want.
Key Sound
You can choose whether to hear clicks, tones or nothing (silent) when you
press the keys.
To set the key sound
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Key Sound, Y E S .
2. Select the key sound you want.
Minute Minder
If you turn on the minute minder, you hear a beep once every minute during
a call.
To turn the minute minder on or off
1. Scroll to Settings, Y E S , Sounds & Alerts, Y E S , Minute Minder, Y E S .
2. Select On or Off.
You can also find the minute minder in Options in the Call Info menu.
Scratchpad
If you make a note of a number during a call, you use the display as a notepad,
see “The Notepad” on page 18. The person you are talking to will hear the
tone signals as you press the keys. If you wish to, you may turn the tone
signals off.
Note! You can only turn the tones on or off during a call.
42
Personalizing Your Phone
2. Select Scratchpad.
To turn the tone signals on during a call
1. Scroll to Call Handling, Y E S .
AB
To turn the tone signals off during a call
1. Scroll to Call Handling, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Select DTMF Mode.
Display Light
You can set the display light to automatic, off or on. In automatic mode, the
display light is turned off automatically a few seconds after you have pressed
the last key. It comes on again when you press a key, open the flip, or when
you receive a call or message.
To set the display light
1. Scroll to Settings, Y E S , Display, Y E S , Light, Y E S .
2. Select the display light setting you want.
Display Language
Most modern SIM cards automatically set the display language to the
language of the country where you bought your SIM card, Automatic. If this
is not the case, the preset language is English.
To change the display language
1. Scroll to Settings, Y E S , Language, Y E S .
2. Select the language you want.
Tip! You can always choose English by pressing u, 0000, d in standby.
You can always choose Automatic by pressing u, 8888, d in standby.
Greeting Text
When you turn on your phone, ‘Ericsson’ appears in the display. Instead of
this, you can write your own greeting.
Note! Some operators may have their own greeting.
To write a new greeting
1. Scroll to Settings, Y E S , Display, Y E S , User Greeting, Y E S .
2. Select Custom.
3. Write your new greeting, using the number keys. For information on how
to enter letters, see “Entering Letters” on page 28.
You may also edit your greeting.
4. Press Y E S to confirm your setting.
Personalizing Your Phone
43
2. Select Standard.
To turn the greeting off
1. Scroll to Settings, Y E S , Display, Y E S , User Greeting, Y E S .
AB
To set the standard greeting
1. Scroll to Settings, Y E S , Display, Y E S , User Greeting, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Select Off.
Phone Number Display
My Numbers allows you to check your phone number(s). If your phone
number cannot be retrieved from your SIM card, you can enter it yourself.
To enter your phone number
1. Scroll to Settings, Y E S , Display, Y E S , My Numbers, Y E S , Voice, Y E S .
2. Enter the number and then press Y E S .
Tip! You can also enter your fax and/or data number and your different
numbers for Line 1 and Line 2, if these are supported by your subscription.
Time
The time is always displayed when the phone is in standby mode.
To set the time format
1. Scroll to Settings, Y E S , Time and Date, Y E S , Time Format, Y E S .
2. Select the 24-hour or 12-hour (am/pm) clock.
To set the clock
1. Scroll to Settings, Y E S , Time and Date, Y E S , Set Time, Y E S .
2. Enter the time in hours and minutes, and press Y E S .
Move from number to number by pressing u or d.
If you select the 12-hour clock, you can alternate between am and pm
by pressing #.
Automatic Time Zone
With the Automatic Time Zone function, you will be asked whether to update
the clock when you enter a new time zone. You can choose to turn the function
off, if you like.
To turn the Automatic Time Zone off
1. Scroll to Settings, Y E S , Time and Date, Y E S , Auto Time Zone, Y E S .
2. Select Off.
Note! This service depends on the network.
44
Personalizing Your Phone
AB
Date
When the phone is in standby mode, you can slide the volume key upwards or
downwards to see today’s date in the Status menu.
To set the date format
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. Scroll to Settings, Y E S , Time and Date, Y E S , Date Format, Y E S .
2. Select the date format you want.
To set the date
1. Scroll to Settings, Y E S , Time and Date, Y E S , Set Date, Y E S .
2. Enter the year (two digits), month and day and then press Y E S .
If you have chosen another date format you must enter the date differently.
Master Reset
You can reset the phone’s settings to the way they were when you bought
your phone.
To reset the phone
1. Scroll to Settings, Y E S , Master Reset, Y E S .
2. Enter the phone lock code (0000) and press Y E S .
The phone lock code may be another one, in case you have changed it.
Personalizing Your Phone
45
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Sending and Receiving
Text Messages (SMS)
The Short Message Service (SMS) allows you to send and receive text
messages consisting of up to 160 characters.
A useful feature in your T28 WORLD is that you can send text messages to a
group which you have defined in your phone book. See “Groups” on page 33.
Instead of calling or sending a text message to the members of that group one
at a time, you can simply send a single group SMS.
If your SIM card does not contain the phone number to your network service
center, you must specify the number yourself. Otherwise you cannot reply to
received messages or send your own messages. See “Enable the Phone to
Send SMS” below.
Note! The Short Message Service may not be available on all networks. Some
network operators may only allow SMS to be sent within their own network.
Enable the Phone to Send SMS
If you want to send or reply to a message, you need to make sure that your
network operator’s Service center number is set. Most modern SIM cards
already contain this information at the time of purchase. You can obtain the
service center number from your network operator.
To activate a service center number found in the list
1. Scroll to Messages, Y E S , Options, Y E S , Service Centers, Y E S .
2. Scroll to the number you want and press Y E S .
3. Select Activate.
If no number is found in the list, you have to set the number yourself.
To enter the phone number to your service center
1. Scroll to Messages, Y E S , Options, Y E S , Service Centers, Y E S , Add new?, Y E S .
2. Enter the number, including the international (+) sign and country code
and press Y E S .
46
Sending and Receiving Text Messages (SMS)
see “Entering Letters” on page 28.
Example:
AB
Composing a Text Message
For more information on how to enter text and the letters,
To enter an ‘A’, press 2 once.
•
To enter a ‘B’, quickly press 2 twice.
•
To enter lower-case letters, enter the letter, for example an ‘A’,
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
and then press *. An ‘a’ appears. Lower-case letters now appear
until you press * again.
•
To enter numbers, press and hold any number key.
•
To delete letters and numbers, press the C key.
You may also use the volume key as a shortcut to certain letters:
•
To enter a ‘B’, slide the volume key upwards and press 2.
•
To enter a ‘C’, slide the volume key downwards and press 2.
Tip! You can choose another alphabet by pressing and holding #.
Sending a New Text Message
1. Scroll to Messages, Y E S , Send New, Y E S .
2. Enter your message and press Y E S .
3. Enter the recipient’s phone number or recall it from the phone book by
pressing u.
4. Press Y E S to send the message.
5. Sending message appears in the display followed by Message has been sent.
Note! If you have turned on any of the Set On Send options (Message Type,
Validity Period, Reply Request), you need to make these choices before entering
the phone number. See “Customizing your Text Messages” on page 48.
Saving the Message for Later Use
If you do not want to send the message now, you can save it in the phone
memory and send it later:
•
Press N O when you are asked to enter a phone number. The message can
now be recalled from the Unsent list in the Messages menu.
To send the message later
1. Scroll to Messages, Y E S , Unsent, Y E S
2. Select the message you want to send.
The message appears in the display.
3. Press Y E S .
Sending and Receiving Text Messages (SMS)
47
If you wish, you may now edit your message.
AB
4. Select Send.
5. Press Y E S and proceed from step 3 as described in “Sending a New Text
Message” above.
Note! The same procedure is used with all types of messages, for example
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
e-mail, fax messages etc. Check with your network operator to find out which
message types you can use.
Sending Text Messages to a Group
With your T28 WORLD you can send text messages to a pre-defined group.
You need to specify a group and save it in your phone book before you can
send text messages to a group. For more information on how to create groups,
see “Groups” on page 33.
To send a text message to a group
1. Scroll to Messages, Y E S , Send New, Y E S .
2. Enter your message and press Y E S .
3. Press u to enter the Phone Book menu.
4. Scroll to Groups and press Y E S .
5. Select the group you want and press Y E S to send the message.
Note! When you send text messages to a group, you will be charged for each
member included in that group.
Customizing your Text Messages
Before you send your message, you can set the type of message, the validity
period and if you want the recipient of your message to reply to your message.
Message Type
Your phone can send different types of messages. Your network operator’s
service center may offer the facility of converting a text message into a format
(e-mail, fax, etc.) that suits the equipment that is going to receive the message.
Please contact your network operator to find out which message types you can
use and how.
You can set a standard message type that you want to use or you can turn on a
Set on Send option, which means that you are asked to select which message
type you want to send, before sending it.
48
Sending and Receiving Text Messages (SMS)
To set a standard message type
2. Select the message type you want.
AB
1. Scroll to Messages, Y E S , Options, Y E S , Message Type, Y E S , Set Default, Y E S .
The selected message type is now standard until you change it.
To turn Set on Send on or off
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. Scroll to Messages, Y E S , Options, Y E S , Message Type, Y E S , Set on Send, Y E S .
2. Select On or Off.
Validity Period
If your message cannot be delivered because the recipient has turned off the
phone, your service center can save the message to send it later. If the service
center has not been able to reach the recipient within a certain time, the
message will be deleted.
You can set a validity period as your standard or you can turn on a Set on
Send option, which means that you are asked to set the validity period before
sending the message.
To set a validity period as your standard
1. Scroll to Messages, Y E S , Options, Y E S , Validity Period, Y E S , Set Default, Y E S .
2. Select the validity period you want.
The selected validity period is now your standard until you change it.
To turn the Set on Send function on or off
1. Scroll to Messages, Y E S , Options Y E S , Validity Period, Y E S , Set on Send, Y E S .
2. Select On or Off.
Reply to Messages
If you want the recipient of your message to reply, you can turn on the
Request Reply option. When this function is on, you are asked to choose if
you want the recipient to reply or not before your message is sent. If you want
the recipient to reply, select On and press Y E S .
To turn the Request Reply function on or off
1. Scroll to Messages, Y E S , Options, Y E S , Reply Request, Y E S .
2. Select On or Off.
Note! Not all network operators support these functions.
Sending and Receiving Text Messages (SMS)
49
AB
Templates
If you have one or more standard messages that you use often, you can save
these as Templates to be reused whenever you want. You can save up to
5 templates which can consist of 30 characters each. Your templates are saved
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
in the phone memory.
To save a template
1. Scroll to Messages, Y E S , Templates, Y E S , Add new?, Y E S .
2. Enter the message and press Y E S .
For more information on how to enter text, See “Composing a Text
Message” on page 47.
3. If you want to send the message now, press Y E S when Send message now?
appears in the display, and proceed as described in “Sending a New Text
Message” on page 47. The message is saved in the list of templates.
4. If you do not want to send the message now, press N O . The message is
saved as a template for later use.
To send a template
1. Scroll to Messages, Y E S , Templates, Y E S .
2. Select the template you want to send.
You may edit the message before sending it. See “Sending a New Text
Message” on page 47.
3. When you have completed the message, press Y E S .
4. Enter the recipient’s phone number.
5. Press Y E S to send the template.
To delete a template
1. Scroll to Messages, Y E S , Templates, Y E S .
2. Select the message you want to delete and then press C .
The message Delete? appears in the display.
3. Press Y E S to delete the message.
Receiving a Message
When you receive a message, you hear a signal, the indicator light on the top
New message
Read now?
of the phone rapidly flashes green and the message New message Read now?
appears in the display.
Note! All networks do not send an audible signal.
50
Sending and Receiving Text Messages (SMS)
AB
To read the message now
1. Press Y E S when you see the question New message Read now?.
The display shows when the message was received and from what number
it was sent, if your network supports the Calling Line Identification service
(CLI). If you have saved the number together with a name in the phone
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
book, the name is shown instead.
2. Scroll through the message using the arrow keys. d takes you forwards
and u takes you backwards through the message. An arrow at the
bottom right corner of the display indicates that there is more text in
the message.
3. At the end of the message, when the arrow in the display disappears,
press Y E S . A new menu with different options appears:
• Delete
• Reply
• Forward
• Save
• Call
• Read Next
The options are described on the following pages.
Note! If the sender of the message wants you to reply, the message
Reply requested Reply? appears in the display when you press Y E S , if this
function is supported by your network operator. If you do not want to reply,
press N O .
To read the message later
•
Press N O when you see the question New message Read now?.
The message is now saved in the phone memory and an envelope icon
appears at the top of the display. The envelope icon disappears as soon as
you have read the message. If you want to read the message later you can
retrieve it from the Inbox menu (see below).
Calling a Phone Number Found in a Message
1. Press Y E S when the number is highlighted.
2. Select Call 0990237237.
Calling the Sender of the Message
1. When you have read the message, press Y E S .
2. Select Call in the option list.
If you have saved the number together with a name in the phone book,
the name of the person who sent the message appears together with Call.
Sending and Receiving Text Messages (SMS)
51
1. When you have read the message, press Y E S .
2. Select Reply in the option list.
AB
Replying to a Message
3. Select what message you want to send as a reply (send a new message or
include this message when replying).
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
4. Enter your message and press Y E S to send the message.
Note! If the sender of the message wants you to reply, the message
Reply requested Reply? appears in the display, if this function is supported by
your network operator, when you press Y E S at the end of the message. Press
YES
again to reply. If you do not want to reply, press N O .
Forwarding a Message
1. When you have read the message, press Y E S .
2. Select Forward in the option list.
You may edit your message before sending it.
3. When you have completed your message, press Y E S .
4. Enter the recipient’s phone number.
5. Press Y E S to send the message.
Deleting a Message
1. When you have read the message, press Y E S .
2. Select Delete in the option list.
Tip! You can also delete a message by pressing C while reading it.
The message Delete? appears in the display. Press Y E S to delete the message.
You can delete a message from the list of messages in the Inbox menu without
having to open it.
To delete a message from the list in the Inbox menu
1. Scroll to Messages, Y E S , Inbox, Y E S .
2. Select the message you want to delete and press C .
The message Delete? appears in the display.
3. Press Y E S to delete the message.
Saving Incoming Messages
If you do not want to read an incoming message at once, it is automatically
saved in the phone memory. This allows you to read it later. If there are any
unread messages in this memory, the envelope icon appears at the top of the
standby display.
52
Sending and Receiving Text Messages (SMS)
The phone memory can hold up to 15 messages. When all memory
is received.
AB
positions are full, the oldest read message is overwritten when a new message
If the phone memory becomes full of unread messages, new messages are
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
automatically saved on the SIM card.
Messages remain in the phone memory until you delete them, until you insert
a different SIM card or until the phone needs the memory space to save new
messages.
The SIM Card Memory
You can save important messages on your SIM card. Messages that are saved
on the SIM card remain there until you delete them, i.e. they will not be
overwritten if you receive any new messages. The maximum number of
messages that you can save depends on your SIM card.
To save a received message in the SIM card memory
1. When you have read the message, press Y E S .
2. Select Save in the option list.
The message automatically moves from the phone memory to the SIM
card memory. The display shows the position of the message and the
Saved on card
3 (15)
number of saved messages, for example the third message of fifteen that
can be saved on the SIM card.
Note! If you save your messages on the SIM card, you can reach them if you
should use your SIM card with another phone.
Reading a saved Message
1. Scroll to Messages, Y E S , Inbox, Y E S .
means an unread message.
means that the message is saved on the SIM card.
2. Select the message you want to read.
3. Read the message as described in “Receiving a Message” on page 50.
4. If you want to read the next message, press Y E S at the end of the message.
5. Select Read Next in the option list.
Sending and Receiving Text Messages (SMS)
53
AB
Area Information
The ordinary Short Message Service is a personal service that carries your
private messages. The Area Information is another type of text message which
is sent to all subscribers in a certain network area.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
The information may be a local road report or a phone number to a local taxi.
Note! This feature may not be available on all networks.
To turn Area Information on or off
1. Scroll to Messages, Y E S , Options, Y E S , Area Info, Y E S , Reception, Y E S .
2. Select On or Off.
Area Information Message Types
Each type of Area Information message is identified by a three-digit code.
The list below shows examples of the Area information codes that exist today.
Code:
AI Message Type:
000
Index
010
Newsflashes
020
Hospitals
022
Doctors
024
Pharmacies
030
Long-distance road reports
032
Local road reports
034
Taxis
040
Weather
050
District BSID
052
Network information
054
Operator services
056
Directory inquiries (national)
057
Directory inquiries (international)
058
Customer care (national)
059
Customer care (international)
Note! These codes are operator dependent. For information about the area
information services that you can use, please refer to the information supplied
by your network operator.
54
Sending and Receiving Text Messages (SMS)
Area Information Message List
AB
You can decide which types of area information messages you wish to receive.
The number of Area Info codes that can be saved depends on your SIM card.
To insert an Area Information code
1. Scroll to Messages, Y E S , Options, Y E S , Area Info, Y E S , Edit List, Y E S ,
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Add new?, Y E S .
2. Enter the new code and press Y E S .
To delete the code
1. Scroll to Messages, Y E S , Options, Y E S , Area Info, Y E S , Edit List, Y E S .
2. Select the code you want to delete and press C .
The message Delete? appears in the display.
3. Press Y E S to delete the code.
Receiving an Area Message
When you receive an Area Information message, the message automatically
appears in the display. You read the message in the same way as you read an
ordinary text message, see “Receiving a Message” on page 50. When you
have read the message, press Y E S . The message is deleted.
BSID
The BSID channel (see “Area Information Message List” on page 55) is used by
network operators for sending messages to their subscribers within a certain
network area. For example, the operator may inform you that you are within
your home network area and that you can now make calls at a lower rate.
Note! This feature may not be supported by your network operator.
To turn BSID on or off
1. Scroll to Messages, Y E S , Options, Y E S , BSID, Y E S ,
2. Select On or Off.
Sending and Receiving Text Messages (SMS)
55
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Diverting Incoming Calls
If you want to make certain that your incoming calls are correctly handled
when you are unable to answer them, you can use the Divert Calls service to
divert them to another phone number.
Note! The Divert Calls service may not be available on all networks.
The Divert Calls service lets you divert your voice, fax and data calls
respectively – provided your subscription supports fax and data calls.
For voice calls, you may choose between the following divert alternatives:
•
divert all voice calls, All Voice Calls
•
divert calls if you are already on the phone, When Busy
•
divert calls that you do not answer within a specified time limit
(operator dependent), No Reply
•
divert calls if your phone is turned off or if you are unreachable,
Not Reachable
Note! These alternatives are only valid for voice calls.
If you subscribe to the Two Line Service, you may set different Divert Calls
for your two voice lines, i.e. Line 1 and Line 2. You will then have an
additional divert alternative, i.e. All Line 2 Calls.
Tip! If you place your T28 WORLD in a specific Ericsson Desktop Charger,
your calls may be diverted automatically. See “Desktop Charger” on page 91.
When you are making a phone call and the phone call is diverted to another
number, this is indicated in your display, if supported by your subscription.
Similarly, when receiving an incoming phone call which has been diverted
from another number, this is indicated in your display, if supported by your
subscription.
Activating Divert Calls
To divert a call
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S .
2. Scroll to the divert you want to turn on (All Voice Calls, When Busy, No Reply,
Not Reachable, Fax Calls or Data Calls) and press Y E S .
3. Select Activate.
56
Diverting Incoming Calls
4. A phone number recently used for the divert function or a number recently
AB
present in the display will be suggested as a divert number. Enter the
phone number, including the area code, to which you want your calls to be
diverted and then press Y E S . If you need to delete numbers, press C .
Tip! If the phone number is stored in the phone book, you do not need to enter
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
it. Press u and then recall the number.
When you turn on the All Voice Calls divert, an icon is shown in standby.
Note! When the Restricted Calls function is on, some Divert Calls options cannot
be activated. See “Security for Your Phone and Subscription” on page 58.
Cancelling Divert Calls
To cancel a certain Divert Calls
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S .
2. Scroll to the divert you want to cancel and press Y E S .
3. Select Cancel.
The message Please wait appears, followed by a message which informs you
that the Divert Calls has been cancelled.
Checking the Divert Status
To check the status of a certain Divert Calls
1. Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S .
2. Scroll to the divert you want to check and press Y E S .
3. Select Get Status.
The message Please wait appears, followed by a message which informs you
whether the Divert Calls is on or not.
To check the status of all Divert Calls
•
Scroll to Settings, Y E S , Call Options, Y E S , Divert Calls, Y E S , Check All, Y E S .
Diverting Incoming Calls
57
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Security for Your Phone
and Subscription
There are several ways to protect your phone and subscription from
unauthorized use. Anything from a SIM card lock to full phone number control.
The SIM Card Lock
The SIM card lock only protects your subscription and not your phone itself
from unauthorized use. If you change SIM cards, the phone still works with
the new SIM card.
Most SIM cards are locked at the time of purchase. If the SIM card lock is on,
you have to enter the PIN (Personal Identity Number) every time you turn on
your phone. If you enter your PIN incorrectly three times in a row, the SIM
card is blocked. This is indicated by the message PIN blocked. If this happens
you need to unblock it to access your subscription.
To unblock your SIM card
1. PIN blocked appears.
2. Enter your PUK (or PUK2) which you will find in the information
supplied by your network operator.
3. Press Y E S .
4. Enter a new four- to eight-digit PIN (or PIN2).
5. Press Y E S .
6. Re-enter the new PIN (or PIN2) to confirm.
7. Press Y E S .
Note! If you enter the wrong PUK ten times in a row, your card is permanently
blocked. If this happens, you should contact your network operator.
To change your PIN code
1. Scroll to Settings, Y E S , Locks, Y E S , Card Lock, Y E S , Change PIN, Y E S .
2. Enter your old (current) PIN and press Y E S .
3. Enter your new PIN and press Y E S .
The phone asks you to repeat the PIN.
4. Enter your new PIN a second time and press Y E S .
The PIN has now been changed.
58
Security for Your Phone and Subscription
Note! If the message Codes do not match appears, this means you entered the
you entered your old PIN incorrectly.
To change your PIN 2
AB
new PIN incorrectly. If the message Wrong PIN appears, followed by Old PIN:,
1. Scroll to Settings, Y E S , Locks, Y E S , Card Lock, Y E S , Change PIN2, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Follow the same procedure as described in ‘To change your PIN code’ above.
To turn off the SIM card lock
1. Scroll to Settings, Y E S , Locks, Y E S , Card Lock, Y E S , Protection, Y E S ,
Off, Y E S .
2. Enter your PIN and press Y E S .
The message Unlocked confirms that the card lock has now been turned off.
Note! This only works if your SIM card allows you to cancel the card lock.
To turn on the SIM card lock
1. Scroll to Settings, Y E S , Locks, Y E S , Card Lock, Y E S , Protection, Y E S ,
On, Y E S .
2. Enter your PIN and press Y E S .
The message Locked confirms that the card lock is now on.
The Phone Lock
The phone lock protects the phone against unauthorized use if it is stolen and
the SIM card is exchanged. It is not on when you buy the phone. You can
change the phone lock code (0000) to any four- to eight-digit personal code.
The phone lock can be On, Automatic or Off.
Phone lock on
If the phone lock is On, the message Phone locked Phone lock code: appears each
time you turn on the phone. You have to enter your code followed by Y E S to
use your phone.
Automatic
If the phone lock is set to Automatic, you do not need to enter your phone
lock code until a different SIM card is inserted in the phone. After the phone
lock code has been entered correctly, the phone can be used with the new
SIM card. You are not asked to enter the phone lock code again until the
original SIM card or a different SIM card is inserted.
Security for Your Phone and Subscription
59
Changing the phone lock code
AB
1. Scroll to Settings, Y E S , Locks, Y E S , Phone Lock, Y E S , Change Code, Y E S .
2. Follow the steps described in “To change your PIN code” on page 58.
Note! It is important that you remember your new code. If you should forget it,
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
you have to hand in your phone to your local Ericsson retailer.
To set the phone lock to on, automatic or off
1. Scroll to Settings, Y E S , Locks, Y E S , Phone Lock, Protection, Y E S .
2. Select On, Automatic or Off.
3. Enter the phone lock code and press Y E S .
The new lock status is shown.
Restrict Calls
The Restrict Calls service allows you to restrict certain types of calls to be
made and received.
Note! This service may not be available on all networks or may require a
separate subscription.
The following calls can be restricted:
•
all outgoing calls, All Outgoing
•
all outgoing international calls, Outgoing Intl
•
all outgoing international calls except to your home country, Outg Intl Roam
•
all incoming calls, All Incoming
•
all incoming calls when you are abroad (when roaming), Inc when Roam
To make sure that a call restriction is not changed by someone else, you need a
password, which comes with your subscription, to turn on or cancel a call
restriction. You can change the password as often as you like.
To activate/cancel a call restriction
1. Scroll to Settings, Y E S , Call Options, Y E S , Restrict Calls, Y E S .
2. Scroll to the option you want and press Y E S .
3. Select Activate or Cancel.
4. Enter your password and press Y E S .
The message Please wait appears, followed by a message which informs you
whether the call restriction is on or not.
Note! If you divert incoming calls you cannot activate some Restrict Calls
options. Likewise, if you restrict calls, you cannot activate some Divert Calls
options. See “Diverting Incoming Calls” on page 56.
60
Security for Your Phone and Subscription
To cancel all call restrictions
2. Enter your password and press Y E S .
AB
1. Scroll to Settings, Y E S , Call Options, Y E S , Restrict Calls, Y E S , Cancel All, Y E S .
The message Please wait appears, followed by a message confirming that all
call restrictions have been cancelled.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To check the status of a call restriction
1. Scroll to Settings, Y E S , Call Options, Y E S , Restrict Calls, Y E S .
2. Scroll to the option you want and press Y E S .
3. Select Get Status.
The message Please wait appears, followed by a message which informs you
whether the call restriction is on or not.
To change the password
1. Scroll to Settings, Y E S , Call Options, Y E S , Restrict Calls, Y E S ,
Change Passwd, Y E S .
2. Enter the old (current) password and press Y E S .
3. Enter the new password and press Y E S .
4. Enter the new password a second time and press Y E S .
The message Please wait appears, followed by a message confirming that the
password has been changed.
Fixed Dialing
Fixed Dialing is a way of restricting outgoing calls. It requires a SIM card that
allows fixed numbers to be saved. The fixed numbers are normally protected by
your PIN2. How many fixed numbers you can save depends on your SIM card.
The Fixed Dialing function allows calls to be made only to certain numbers
saved on the SIM card. If an attempt is made to call other numbers, the
message Number not permitted appears in the display.
It is possible to save partial numbers, for example an area code, or an area
code followed by the first digits common to several numbers. Storing
0123456 allows calls to be made to all numbers starting with 0123456.
Numbers beginning with the international (+) sign and country code can also
be saved, allowing you to make calls abroad.
Numbers which include question marks can be saved. A question mark should
be read as a wild card, i.e. it can represent any number (0-9). To enter a
question mark press and hold #.
Note! The Fixed Dialing service does not prohibit calls to the international
emergency number 112 (or 911 in the Americas).
Security for Your Phone and Subscription
61
2. Enter your PIN2 and press Y E S .
3. Select On or Off.
To save fixed numbers
AB
To turn the Fixed Dialing service on or off
1. Scroll to Phone Book, Y E S , Options, Y E S , Fixed Dialing, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S , Add new?, Y E S .
2. Enter your PIN2 and press Y E S .
3. Enter the fixed number and press Y E S .
4. Enter the name you want to link with the number and press Y E S .
To edit a saved fixed number
1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S .
2. Scroll to the fixed number that you want to edit and press Y E S .
3. Select Edit.
4. Enter your PIN2 and press Y E S .
5. Edit the fixed number and press Y E S .
6. Edit the name and press Y E S .
7. Enter the position number and press Y E S .
To delete a fixed number
1. Scroll to Phone Book, Y E S , Fixed Numbers, Y E S .
2. Scroll to the fixed number that you want to delete and press Y E S .
3. Select Delete.
4. Enter your PIN2 and press Y E S .
The fixed number is deleted.
Closed User Groups
The Closed User Group (CUG) function is another way of lowering call
costs. It depends entirely on your operator and subscription. Not all networks
support this function.
Your network operator can place certain numbers in groups. On some
networks it is cheaper to make calls within a call group. You can have a
maximum of 10 groups.
To add a Closed User Group
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S , Edit List, Y E S ,
Add new?, Y E S .
2. Enter the name of the Closed User Group and press Y E S .
3. Enter the index number of the group and press Y E S .
Note! The index numbers are provided by your network operator.
62
Security for Your Phone and Subscription
To activate a Closed User Group
2. Scroll to the group you want to activate and press Y E S .
3. Select Activate.
Calls can only be made within the selected user group.
AB
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S , Edit List, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To call outside Closed User Groups
You can decide whether outgoing calls to a non-CUG number are allowed.
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S ,
Open Calls, Y E S .
2. Select On.
To edit a name in the CUG List
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S , Edit List, Y E S .
2. Scroll to the group that you want to edit and press Y E S .
3. Select Edit.
4. Enter a new name and press Y E S .
To delete a group from the CUG List
1. Scroll to Settings, Y E S , Call Options, Y E S , Closed Groups, Y E S , Edit List, Y E S .
2. Scroll to the group that you want to delete and press Y E S .
3. Select Delete.
Call Screening
With the Call Screening service, you can choose to receive calls only from
certain numbers. Other calls are automatically rejected by a busy signal.
You have to save the numbers that you want to receive in an Accepted List.
The rejected calls are saved in the Call Log in the Call Info menu. When you
buy your phone, the setting for the Call Screening service is set to Accept All
Calls, i.e. you receive calls as normal.
To add numbers to the Accepted Callers List
1. Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S , Accepted List,
Y E S , Add new?, Y E S .
This takes you to your phone book.
2. Select a number.
To add more participants in the Accepted Callers List, repeat steps 1 to 2 above.
It is possible to choose a number within a group in your phone book.
To delete numbers from the Accepted Callers List
1. Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
Accepted List, Y E S .
2. Scroll to the number you want to delete and press C .
Security for Your Phone and Subscription
63
Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
Accepted List, Y E S .
To Accept calls from the list
1. Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
AB
To check the Accepted Callers List
•
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Accept Options, Y E S .
2. Select From List.
Now you will only receive calls from the participants in the
Accepted Callers List. An icon is shown in standby.
To reject all calls
1. Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
Accept Options, Y E S .
2. Select Accept none.
All incoming calls will now be rejected. The caller hears a busy signal and
you get no indication of incoming calls. An icon is shown in standby.
To accept calls from all
1. Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
Accept Options, Y E S .
2. Select Accept All Calls.
You will now receive all calls as normal.
To check the Accepted Calls function
•
Scroll to Settings, Y E S , Call Options, Y E S , Call Screening, Y E S ,
Accept Options, Y E S .
The Accepted Calls alternative that is on is marked with a filled button.
64
Security for Your Phone and Subscription
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Handling More than One
Call Simultaneously
Your phone allows you to handle more than one call simultaneously.
This means that you can put a call that is in progress on hold, while you make
or answer a second call, and then switch between the two calls.
You may also set up a Conference Call to have a joint conversation with up
to five people. You may put an individual or a group of conference members
on hold while you add other people to the conference call. You may also
put conference members on hold while you talk to someone privately.
See “Conference Calls” on page 67.
The Call Waiting Service
If you wish to be able to receive a second call, while another call is in
progress, you must turn on the Call Waiting service.
Note! The Call Waiting service may not be available on all networks.
If you are engaged in a fax or a data call, you will not hear any incoming
calls. Incoming calls are rejected.
To turn on the Call Waiting service
•
Scroll to Settings, Y E S , Call Options, Y E S , Call Waiting, Y E S , Activate, Y E S .
There may be a short delay before the network responds. In the meantime,
the message Please wait is displayed. This is followed by the message
Call Waiting Activated.
To cancel the Call Waiting service
•
Scroll to Settings, Y E S , Call Options, Y E S , Call Waiting, Y E S , Cancel, Y E S .
To check whether the Call Waiting service is on or not
•
Scroll to Settings, Y E S , Call Options, Y E S , Call Waiting, Y E S , Get Status, Y E S .
Making a Second Call
1. Put the current call on hold by pressing Y E S .
Call on hold
2. Enter the number you wish to call and press Y E S .
You may also retrieve the number from your phone book by pressing and
holding d.
Note! You can only put one call on hold.
Handling More than One Call Simultaneously
65
AB
Receiving a Second Call
If the Call Waiting service is on, you hear a tone in the earpiece if you receive
a second call. The number or name of the caller is normally shown at the top
of the display together with a list of the alternatives Answer, Busy and
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Release&answer. If the incoming call is a restricted number, the display
shows Withheld. If the incoming call is a number without any CLI service,
Unknown is shown.
You can do one of the following:
Put the current call on hold and answer the waiting call
•
Press Y E S to answer the waiting call.
The current call is now put on hold.
Your held call is marked in gray in the display and the active call is marked
in black.
Continue the current call and reject the waiting call
•
Select Busy.
The waiting call is rejected. If the caller’s network supports it, the caller
hears a busy signal.
Note! If Divert When Busy is on, the waiting call is diverted to the number
you have specified.
End the current call and answer the waiting call
•
Select Release&answer.
One Active Call and One Call On Hold
When you have one active call and one call on hold, you can do one of the
following:
Switch between the two calls
•
Press Y E S .
End the active call and return to the call on hold
1. Press N O . The question Retrieve call? appears.
2. Press Y E S .
If you press N O , also the call on hold will be ended.
End both calls
•
66
Scroll to Call Handling, Y E S , Release All, Y E S .
Handling More than One Call Simultaneously
Scroll to Call Handling, Y E S , Transfer Call, Y E S .
AB
Connect the two calls (Call Transfer)
•
The two calls are now connected to each other, and you are disconnected
from both calls.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Note! The Call Transfer service may not be available on all networks.
Join the two calls into a Conference Call
•
Scroll to Call Handling, Y E S , Join Calls, Y E S .
See ‘Conference Calls’ below.
Receiving a Third Call
If the Call Waiting service is on, you may receive a third call when you have
one active call and a second call on hold. From now on, you cannot answer any
more calls without disconnecting one, if you do not want to create a conference
call. You hear a tone in the earpiece and Busy and Release&answer appear in
the display.
You can do one of the following:
End the current call and accept the waiting call
•
Select Release&answer.
The waiting call becomes active and the call on hold remains on hold.
Reject the waiting call
•
Select Busy.
The third call is rejected. Provided the caller’s network supports this
function, the caller hears a busy signal.
Create a conference call
•
See below
Conference Calls
Note! The Conference Call service may not be available on all networks.
A conference call is a call with more than two participants. As in an ordinary
conference, all participants can hear each other at the same time. You may
include up to five participants in a conference call.
Creating a Conference Call
To create a conference call, you must have one active call and one call on hold.
To join the two calls into a conference call
•
Scroll to Call Handling, Y E S , Join Calls, Y E S .
You have now created a conference call (with yourself and the active and
held calls).
Handling More than One Call Simultaneously
67
Adding New Participants to the Conference Group
To add a new participant
1. Press Y E S to put the conference group on hold.
AB
You may put the conference group on hold and then add new participants.
2. Call the next person you wish to include in the conference group.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
3. Scroll to Call Handling, Y E S , Join Calls, Y E S .
You can include up to five participants in the conference group by
repeating steps 1 to 3 above.
To check the participants in the conference group
1. Scroll to Call Handling, Y E S , Parties in Conf, Y E S .
The first participant’s phone number is displayed, if available. If the
participant’s number and name are stored in your phone book, the name is
displayed instead. Otherwise the display shows part 1, 2 etc.
2. Scroll with d to check the other participants.
Having a Private Conversation with One of the Participants
If you wish to have a private conversation with one of the participants, you
may extract that participant from the conference and put the other participants
on hold.
To extract a participant
1. Scroll to Call Handling, Y E S , Extract Part, Y E S .
2. Select the participant that you want to extract.
To rejoin the participant to the conference group
•
Scroll to Call Handling, Y E S , Join Calls, Y E S .
Releasing Participants from the Conference Group
You can release participants from the conference group one by one or
all at once.
To release a certain participant
1. Scroll to Call Handling, Y E S , Release Part, Y E S .
2. Select the participant that you want to release.
To release all participants
•
68
Scroll to Call Handling, Y E S , Release All, Y E S .
Handling More than One Call Simultaneously
Making a Call while a Conference Call Is in Progress
switch between the new call and the conference call.
To put the conference group on hold and make a new call
1. Press Y E S .
AB
You can put the conference group on hold and make another call. You can then
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Enter the number you wish to call and press Y E S .
To switch between the new call and the conference group
•
Press Y E S .
To end the new call and return to the conference group
•
Press N O and then Y E S .
Ending the Conference Call
•
Close the flip or press N O .
Handling More than One Call Simultaneously
69
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Setting Network
Preferences
Searching for Networks
When you turn on the phone, it searches for the last accessed network. If this
is not within range, you may use another network, provided your home
network has an agreement that allows you to do so. This is called roaming.
The order of preference in which the phone chooses a network is determined
by a list of preferred networks on your SIM card. Your phone includes a
number of functions that let you determine how it searches for a network.
You may also choose a network yourself from those within range.
To select a network
1. Scroll to Settings, Y E S , Networks, Y E S , Select Network, Y E S .
2. If there is more than one network within range, scroll to the network you
want and press Y E S to select it.
To start an automatic network search
•
Scroll to Settings, Y E S , Networks, Y E S , New Search, Y E S .
The phone automatically starts searching for a network according to the
list of preferred networks stored on your SIM card.
Display Information
The currently used network is marked with a filled button. Together with the
network name, you also get the following information in the display:
The display shows...
meaning...
You are in your home zone.
Does not appear on all networks.
The name of the network is included in a list of
preferred networks on your SIM card. You can use
this network.
The name of the network is included in a list of
forbidden networks on your SIM card. You may not
be allowed to use this network, except for
emergency calls.
70
Setting Network Preferences
All other networks without any icons are available, i.e. they are not included
AB
in the preferred or forbidden list on your SIM card but they may be used.
Forbidden Networks
The names of the forbidden networks are stored on your SIM card. If such a
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
forbidden network is within range, it is left out when the phone searches for a
network (automatic search mode).
If your home network and a forbidden network come to an agreement that
allows you to use the forbidden network, you can select this network even
though the message Forbidden is displayed.
List of Preferred Networks
You can create and edit a list that defines in which order your phone will
select a network during automatic network selection, when your home
network is not within range.
The number of networks that can be stored in the list depends on your SIM card.
You can review the network list and rearrange the order of the networks.
You can also add new networks to the list and delete networks from it.
To review the list of networks
•
Scroll to Settings, Y E S , Networks, Y E S , Preferred Nets, Y E S .
The name of the first network is displayed.
Use u or d to scroll through the networks in the list.
To see a network’s full name
1. Scroll to Settings, Y E S , Networks, Y E S , Preferred Nets, Y E S .
2. Scroll to a network and press Y E S .
3. Select Full Name.
To add a network to the list
1. Scroll to Settings, Y E S , Networks, Y E S , Preferred Nets, Y E S , Add new?, Y E S .
2. Scroll to the network that you want to add and press Y E S .
If the network you want does not appear in the list, scroll to Other and press
YES.
Enter the three-digit country number and the two-digit network
number and press Y E S .
3. Enter a position number and press Y E S .
Note! All lower prioritized networks will be shifted one step down in the list.
Setting Network Preferences
71
2. Scroll to the network that you want to delete and press Y E S .
3. Select Delete.
To rearrange the list
AB
To delete a network from the list
1. Scroll to Settings, Y E S , Networks, Y E S , Preferred Nets, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. Scroll to Settings, Y E S , Networks, Y E S , Preferred Nets, Y E S .
2. Scroll to the network that you want to move and press Y E S .
3. Select Change Priority.
4. Enter the new position within the list and press Y E S .
Search Modes
When you turn on your phone, it searches for a network. This can be done in
two different ways, depending on the search mode that is on. When you buy
your phone it is set to automatic search mode.
Automatic search mode means that your phone searches for the last accessed
network first. If this is not available, it automatically searches for another
available network within range.
Manual search mode means that your phone searches for the last accessed
network first. If this is not available, the question Select net? appears. You then
need to choose a network as described in “Searching for Networks” on
page 70.
To turn on the automatic search mode
•
Scroll to Settings, Y E S , Networks, Y E S , Search Mode, Y E S , Automatic, Y E S .
To turn on the manual search mode
•
72
Scroll to Settings, Y E S , Networks, Y E S , Search Mode, Y E S , Manual, Y E S .
Setting Network Preferences
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Knowing the Call Time/
Call Cost
During a call, the duration of the call is shown in the display. When you end
the call, the call duration information is shown for another three seconds.
If you subscribe to cost information, the call cost (or the number of call units)
is displayed instead of the call duration.
Total Call Time or Call Cost
The Call Info menu allows you to check the total time or cost of your calls.
To check the time/cost of the last call
•
Scroll to Call Info, Y E S , Last Call, Y E S .
Now you can check the duration or cost (if you subscribe to cost
information) of the last call.
To check the time of your outgoing calls
•
Scroll to Call Info, Y E S , Outgoing Time, Y E S .
To check the total call time
•
Scroll to Call Info, Y E S , Total Time, Y E S .
To check the total call cost
•
Scroll to Call Info, Y E S , Total Cost, Y E S .
To reset the total call time/call cost
1. Scroll to Call Info, Y E S , Reset Counters, Y E S .
2. Select Total Cost, Total Time or Outgoing time.
3. Press Y E S to reset the cost or time.
Note! If you subscribe to cost information, you must enter your PIN2 to clear
the cost or time counter.
Determining the Call Cost
The Price function lets you enter and specify the price per call unit. The price
entered is stored on your SIM card.
Knowing the Call Time/Call Cost
73
Note! This service must be supported by your subscription and your network.
AB
If you do not specify a price per call unit, the number of call units is displayed
during a call, and in Last Call and Total Cost in the Call Info menu.
To enter the price per call unit
1. Scroll to Call Info, Y E S Options, Y E S , Set Price, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Enter your PIN2 and press Y E S .
3. Select Change Price.
4. Enter the code for the currency you want, for example USD for US
Dollars, and then press Y E S .
5. Enter the price per call unit, for example 0.75, and press Y E S . To enter the
decimal point, press #.
To revert to call units
1. Scroll to Call Info, Y E S , Options, Y E S , Set Price, Y E S .
2. Enter your PIN2 and press Y E S .
3. Select Units.
Credit Limit for Calls
If both your network and SIM card support this feature, you can enter a total
amount of money that can be used for making calls. This could be useful when
you lend your phone to someone and do not want their call costs to exceed a
certain amount which you can decide. After a call is made, the cost is
deducted from this amount. When the amount reaches zero, no more calls can
be made.
Note! As the price of a call may vary due to where you are calling from,
at what time of the day you are calling and so on, the credit limit is only an
estimated value.
To set a specific credit limit
1. Scroll to Call Info, Y E S , Options, Y E S , Set Credit, Y E S .
2. Enter your PIN2 and press Y E S .
3. Select Change Credit.
4. Enter the amount, for example 50 dollars, and then press Y E S .
To set unlimited credit
1. Scroll to Call Info, Y E S , Options, Y E S , Set Credit, Y E S .
2. Enter your PIN2 and press Y E S .
3. Select Unlimited?.
Note! If you set the credit to Unlimited, the cost counter starts from zero and
increases.
74
Knowing the Call Time/Call Cost
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Using Two Voice Lines
If your subscription supports the Two Line Service, your phone will have two
voice lines with different phone numbers, separate bills and perhaps different
subscription services. This is useful for example if you want to keep business
calls and private calls on separate lines.
When you buy your phone, the names of the lines are normally Line 1 and Line
2, but you can change their names. You can only send text messages (SMS) on
Line 1. An icon indicates the line currently chosen for outgoing calls.
To change the name of a line
1. Scroll to Settings, Y E S , Display, Y E S , Edit Line Tags, Y E S .
2. Select a line.
3. Enter a new name and press Y E S .
Changing Phone Lines
When you want to make a call, you need to choose which line to use.
Note! Incoming calls can be received on both lines no matter which line is
currently chosen.
To change phone lines
1. Scroll to Call Handling, Y E S .
2. Select Switch to Line 1 or Switch to Line 2.
From now on, all outgoing calls are made on this line.
Different Settings for Each Line
You may have different settings for each line, for example the ring signal or
divert calls.
Tip! You may also have separate Voice Mail numbers for each phone line, if
supported by your subscription.
Some operators may show the call time or call cost for each line respectively.
Using Two Voice Lines
75
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Voice Control
Your phone allows you to:
•
voice dial - call someone by simply saying the name
•
answer and reject calls using your voice when connected to a handsfree kit
To call someone, you only need to press Y E S until you hear a tone, say the
name (voice label) linked with that person and your phone automatically dials
the number. To answer or reject calls, say Answer or Busy.
Preparing your Phone for Voice Dialing
When you buy your phone, voice dialing is set to on. If, for some reason, it has
been turned off, you will need to turn it on again before you can start using it.
To turn Voice Dialing on
1. Scroll to Settings, Y E S , Voice Control, Y E S , Voice Dialing, Y E S .
2. Select On.
Your phone is now ready to record voice labels.
Note! Once you have turned voice dialing on, you are asked if you want to
record a voice label every time you save a new number in your phone book.
See “Saving a Number Together with a Name” on page 29.
Before you can use voice dialing, you need to record voice labels for your
phone book entries. To get a good result when recording voice labels, make
sure you are in a quiet environment.
To record voice labels for existing phone book entries
1. Scroll to Phone Book, Y E S , Voice Labels, Y E S , Add voice?, Y E S .
2. Select a phone book entry to which you want to add a voice label.
3. Wait for the tone and say the name (voice label) that you want to save.
The voice label is played back to you.
4. Press Y E S to save the voice label you have recorded.
If you do not find the recording OK, repeat step 3.
An icon appears next to those phone book entries for which you have saved a
voice label. You can save 10 voice labels in the phone.
You can also record voice labels in Find and Edit in the Phone Book menu.
76
Voice Control
Note! To use voice dialing with a vehicle handsfree unit, you need to record
AB
your voice labels in the car, when connected to a vehicle handsfree.
Voice labels for phone book entries recorded in the phone will not be available
in the car, and vice versa. For more information about the Vehicle Handsfree
unit, see “Vehicle Handsfree” on page 93.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Recording Problems
If your phone cannot detect any speech, one of the following might have
happened:
•
you spoke too softly - try speaking louder
•
the voice label was too short - it should be around one second long
•
you spoke too late or too soon - speak after the tone
Go back to step 1 of ‘To record voice labels for phone book entries’.
Listening to and Editing Voice Labels
Your phone allows you to listen to and edit a list of the phone book entries that
have voice labels.
To listen to and/or edit the voice labels saved in your phone book
1. Scroll to Phone Book, Y E S , Voice Labels, Y E S .
2. Scroll to the entry that you want to edit.
The voice label is played back to you.
3. Press Y E S .
4. Select Replace Voice if you want to re-record the voice label or select
Delete Voice if you want to delete the recorded voice label.
5. Continue according to the instructions.
You can also listen to and/or edit your voice labels in Find and Edit in the
Phone Book menu.
Voice Label Playback
If you have recorded a voice label for an entry in your phone book, the voice
label is played back to you in the following cases:
•
when you move through the phone book or voice label list and reach
this entry
•
when you receive a call from the number corresponding to this entry
•
when you voice dial this entry (before the call is connected)
Making Calls Using your Voice
To make a call
1. Press and hold Y E S until you hear a tone.
2. Release Y E S and say a name that you have recorded earlier.
The name (voice label) is played back to you, and the call is connected.
Voice Control
77
Instead of pressing and holding Y E S , as in step 1 above, you can slide and
AB
hold the volume key when the flip is open. A third alternative is to initiate
voice dialing by just opening the flip, but then Start on Open must be on.
To turn on Start on Open
1. Scroll to Settings, Y E S , Voice Control, Y E S , Start on Open, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
2. Select On.
When Start on Open is on, an icon appears in standby.
Voice Answering
When connected to a portable or vehicle handsfree unit, you can answer or
reject incoming calls by using your voice.
Before you can use voice answering, you need to turn on the voice answering
function and record your voice commands.
To turn on Voice Answering
1. Scroll to Settings, Y E S , Handsfree, Y E S , Voice Answer, Y E S .
2. Select On.
You now have to train your phone to recognize your voice answering
commands.
3. Press Y E S to continue.
4. Follow the instructions in the phone display, i.e. say the word Answer and
press Y E S to save your recording. (Use the microphone of the Handsfree
unit.) If the recording was not OK, repeat step 3.
5. Say the word Busy and press Y E S to save your recordings.
Note! If you prefer, you can use other words instead of ‘Answer’ and ‘Busy’.
To answer an incoming call using your voice
•
When the phone rings, say the word Answer.
The word Answer is played back to you and the call will be connected.
To reject an incoming call
•
When the phone rings, say the word Busy.
The word Busy is played back to you, and the call is rejected, i.e. the caller
hears a busy signal.
Note! For more information about handsfree units, see “Portable Handsfree”
on page 92 and “Vehicle Handsfree” on page 93.
78
Voice Control
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Calling Card Calls
When making international or long distance calls, you may not want your
operator to charge you for these calls on your normal account. If you have a
credit card or a calling card, you may want to redirect the charges to one of
these accounts instead. The Calling card service lets you redirect the charges
to either a credit card account or to a calling card account.
You can save two separate card numbers in your phone. These numbers are
protected by a four- to eight-digit phone lock code. When you buy your phone
the code is set to 0000. You may change the code to one that you choose
yourself. See “The Phone Lock” on page 59.
Note! You cannot use the Calling card service when making a fax or a data call.
Activating the Calling Card Service
To be able to make calling card calls, you need to turn on the service.
To turn on the Calling card service
1. Scroll to Phone Book, Y E S , Options, Y E S , Set CallingCards, Y E S .
2. Enter your phone lock code (0000) and press Y E S .
3. Select On.
The Calling card service is now on and the sub-menu Calling Cards is
available in the Phone Book menu.
Saving Calling Card Numbers
You can save two calling card numbers in your phone.
To save a card number
1. Scroll to Phone Book, Y E S , Calling Cards, Y E S .
2. Enter your phone lock code and press Y E S .
3. Select Add new?.
4. Enter the access number of the calling card server and press Y E S .
5. Enter a name that you want to link with your calling card server and
press Y E S .
6. Enter the verification code of the calling card server and press Y E S .
7. Select whether you want to send the number that you want to call or the
verification code first and press Y E S to confirm your choice.
Calling Card Calls
79
verification codes.
To delete a card number
1. Scroll to Phone Book, Y E S , Calling Cards, Y E S .
AB
Note! Your service provider will give you the information needed for the
2. Scroll to the card number that you want to delete and press Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
3. Select Delete.
The question Delete? appears in the display.
4. Press Y E S .
The card number has been deleted.
To edit a card number
1. Scroll to Phone Book, Y E S , Calling Cards, Y E S .
2. Scroll to the card number that you want to edit and press Y E S .
3. Select Edit.
You may now edit the card number.
4. Press Y E S to confirm the new number.
You may now also edit the name and code.
Choosing a Card
If you have saved two card numbers, you must choose which card you want to
use before making a calling card call.
To select a card
1. Scroll to Phone Book, Y E S , Calling Cards, Y E S .
2. Enter your phone lock code and press Y E S .
3. Select the card that you want to use.
4. Select Activate card.
Making a Calling Card Call
1. Enter the phone number of your calling card server or retrieve it from the
Phone Book by pressing and holding d.
2. Press and hold Y E S .
The access number of the calling card server is called and during the
connecting phase, you are asked to send the phone number of the person
that you want to call and the verification code, in the order chosen earlier
(see above).
3. To send the number and verification code during the connecting phase,
press Y E S when the display shows Send or wait a few seconds and they are
sent automatically. Now you are connected to your personal phone call.
80
Calling Card Calls
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Sending and Receiving
Fax and Data Calls
Note! To be able to use various communications services you need the
appropriate software such as a fax program, an e-mail program or an
Internet browser.
Sending Fax and Data Calls
All fax and data calls are initiated from the appropriate computer software.
To send fax and data calls you need to connect your phone to a computer,
for example by means of an infrared modem and then start the appropriate
software program.
Receiving Fax and Data Calls
The procedure of receiving fax and data calls depends on your network and
subscription. If you have different numbers for voice, fax and data calls, this is
referred to as multi numbering. This means that you can have up to three
numbers in your subscription. If you only have one number for all call types,
this is referred to as single numbering.
Receiving Fax and Data Calls – Multi Numbering
If your network and subscription support multi numbering, the type of
incoming call is shown in the display. There are two possible calls apart from
voice calls:
•
Fax calls
•
Data calls
The display shows the type of call.
To receive a fax or data call
1. Connect your computer to the phone.
2. Answer the call from within the software program (if it does not answer
automatically).
Note! You cannot answer an incoming fax or data call by pressing the Y E S
key on the phone but you may reject the call by pressing N O .
Sending and Receiving Fax and Data Calls
81
Receiving Fax and Data Calls – Single Numbering
the phone does not recognize the type of incoming call.
Next Incoming Call Type
AB
If you have a SIM card that does not support separate fax and data numbers,
If you want to receive a fax or data call you have to set the phone to one of
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
these options in the Next Incoming sub-menu. You only see this menu if your
phone detects that you do not have separate numbers for data, fax and voice.
Once you have set your phone for a specific incoming call, it stays like this
until you change it. The default setting is Voice.
To set the next incoming call type
1. Scroll to Call Handling, Y E S , Next Incoming, Y E S .
2. Select the call type you want (Voice, Data or Fax).
82
Sending and Receiving Fax and Data Calls
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Extras
Alarm Clock
The phone has an alarm clock, which you may find useful when travelling.
When it is on, an icon is shown in the display.
The alarm rings at the time set and the display flashes, even if the phone is
turned off. The volume of the alarm signal is always increasing, provided the
battery is attached and charged.
The alarm rings for 60 seconds and is repeated every nine minutes, if you do
not turn it off. After 60 minutes, the repeat function is turned off
automatically.
To set the time of the alarm
1. Scroll to Extras, Y E S , Alarm Clock, Y E S .
2. Enter the time.
3. Press Y E S to confirm your setting.
To change the alarm time
1. Scroll to Extras, Y E S , Alarm Clock, Y E S , Set New Time, Y E S .
2. Enter the time.
3. Press Y E S to confirm your setting.
To turn the alarm signal off
•
Press any key to turn the alarm off when it rings.
If you do not want the alarm to be repeated, press Y E S .
To turn off the alarm function
1. Scroll to Extras, Y E S , Alarm Clock, Y E S .
2. Select Cancel.
You can also find the Alarm Clock in Time and Date in the Settings menu.
Extras
83
AB
Calculator
The phone has a built-in calculator, which can add, subtract, divide
and multiply.
Press # to get +, -, x, /.
•
Press C to delete a figure to the left of the cursor.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
Press * to enter a decimal point.
•
To use the calculator
In this example we are going to divide 134 by 32.
1. Scroll to Extras, Y E S , Calculator, Y E S .
2. Enter 134.
3. Press # repeatedly until the division sign (/ ) appears.
4. Enter 32.
5. Press Y E S to get the answer.
6. To clear the display, press C .
Stopwatch
The phone has a built-in stopwatch for you to time a certain activity.
To run the stopwatch
1. Scroll to Extras, Y E S , Stopwatch, Y E S .
2. Press Y E S to start the stopwatch. Press Y E S again to stop it.
To reset the stopwatch
Press C when the stopwatch is not running.
•
Tip! By pressing # when the stopwatch is running, you can store up to 9 lap
times. Press u or d to check your stored lap times.
Note! If you receive an incoming call or voice or text message while the
stopwatch is running, the stopwatch is turned off. If you exit the stopwatch
menu, the stopwatch is turned off.
Timer
The phone has a built-in 24-hour timer. You set the time you want and when
that time is out, an alert signal sounds.
To set the timer
1. Scroll to Extras, Y E S , Timer, Y E S .
2. Enter the time and press Y E S .
The countdown begins. The timer is shown in standby mode.
When the alert sounds, press any key to turn it off.
84
Extras
2. Enter the time and press Y E S .
AB
To set a new time when the timer is running
1. Scroll to Extras, Y E S , Timer, Y E S , Set New Time, Y E S .
The countdown begins. The timer is shown in standby mode.
When the alert sounds, press any key to turn it off.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To turn off the timer
1. Scroll to Extras, Y E S , Timer, Y E S .
2. Select Cancel.
Note! The timer does not work when the phone is turned off.
Games
Your phone has two different games for your enjoyment. There are help texts
available in each game as a guide for you to get started.
Tetris®
The object of Tetris is to prevent the blocks from reaching the top. Each time
you fill a line, the line disappears.
To start Tetris
1. Scroll to Extras, Y E S , Games, Y E S , Tetris, Y E S .
Tetris appears in the display.
2. To start a game, select Start.
3. Select level (1–10).
4. Press any key to start.
Instead of choosing Start you can scroll with d to select
•
High-score, Help or Quit (at step 2 above).
To control the game
•
8 or slide the volume key downwards = move left
•
2 or slide the volume key upwards = move right
•
5 or 9 = rotate
•
3 or 6 = drop faster
•
C
•
NO
= pause
= quit
Tetris®; © Elorg 1987. Classic Tetris™; © Elorg 1998
Tetris Logo by Roger Dean; © The Tetris Company 1997
All Rights Reserved.
Extras
85
Solitaire
AB
The object of Solitaire is to form four piles of cards, one per suit, running
from ace to king. The cards are dealt out into seven columns. The last six
columns have one or more cards facing downwards. If the top card in a
column is removed, revealing the face-down card, you may turn it face up.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Only kings, or stacks of cards beginning with a king may be moved to an
empty column.
Columns of cards are built up in descending order and alternating colour.
For example, the eight of hearts may be placed on either the nine of clubs
or spades.
The remaining cards in the deck are available for play. You can turn these
cards one at a time. The card in the discard pile may be placed on the columns
or the ace piles. When you run out of cards in the deck, you can flip it over
and continue.
To start Solitaire
1. Scroll to Extras, Y E S , Games, Y E S , Solitaire, Y E S .
Solitaire appears in the display.
2. To start a game select New game (or Resume game if you have played before).
•
Instead of choosing Start you can scroll with d to select
Resume game or Help (at step 2 above).
To control the game
86
•
1 = Select card/pile, Confirm move, Flip card
•
2 = Turn up new card from game deck
•
3 = Put card on ace pile
•
4 = View a pile (selection and move is possible)
Extras
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
The Profile Concept
Your phone includes a number of pre-programmed profiles. A profile is a
group of settings which are set to suit a certain environment. For example,
when you go to a meeting, you can just choose the Meeting profile and a
number of settings that suit a meeting are set.
Some accessories can choose a profile automatically. For example, when you
place your phone in a vehicle handsfree unit, the In Car profile is chosen.
For more information on automatic activation of profiles. See “Accessories”
on page 90.
The Profiles
There are six pre-programmed profiles:
•
Normal
•
Meeting
•
In Car
•
Outdoors
•
Port H-free
•
Home
Your phone is always set to one of the six profiles. When you buy your phone,
it is set to the Normal profile. You cannot create more profiles, but you can
change the name of a profile, change the settings included in a profile or add
an accessory to a certain profile.
Note! You cannot change the name of the Normal profile and you cannot add
an accessory to the Normal profile.
For information on how to add an accessory to a profile, see “Adding
Accessories to a Profile” on page 96.
Tip! To find out which profile you are using, slide the volume key upwards or
downwards in standby mode.
The Profile Concept
87
The table below shows the settings of each profile.
Meeting
In Car
Outdoors
Port H-free Home
5(6)
0(6)
6(6)
6(6)
6(6)
Increasing Ring Off
Off
Off
Off
Off
Vibrate Mode
On if silent Off
On
On
On
5(6)
Off
Off
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Ring Volume
AB
Normal
Call Screening
Accept
Accept All Accept All Accept All Accept All Accept All
All Calls Calls
Calls
Calls
Calls
Calls
Divert Calls
Off
Off
Off
Off
Off
Off
Calling Cards
None
None
None
None
None
None
Light
Auto
Auto
On
Auto
Auto
Auto
Line 1/2
L1
L1
L1
L1
L1
L1
Silent
Off
On
Off
Off
Off
Off
Auto Activation Off
Off
On
Off
On
Off
Accessories
-
Vehicle HF -
-
Handsfree -
You can always choose a profile manually.
To select a profile manually
1. Scroll to Settings, Y E S , Profiles, Y E S , Select Profile, Y E S .
2. Select the profile you want.
You can also find Select Profile in the My Shortcuts menu. The quickest way
to reach this sub-menu is to press and hold u.
If you choose a profile other than Normal, an icon is shown in standby.
Note! A profile which is not linked with any accessory, such as Meeting or
Normal, must be chosen manually, even if automatic activation is on.
The profiles linked with accessories can be chosen automatically.
See “Accessories” on page 90.
Changing the profile settings
You can re-name the pre-programmed profiles and change the settings
according to your wishes.
To change the name of a profile
1. Scroll to Settings, Y E S , Profiles, Y E S , Profile Name, Y E S .
2. Enter a new name and press Y E S .
88
The Profile Concept
A list of the profile settings appears.
2. Select a setting by pressing Y E S .
3. Change the profile setting according to your wishes.
AB
To change a profile setting
1. Scroll to Settings, Y E S , Profiles, Y E S , Edit Profile, Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
For information, see the relevant chapters “Personalizing Your Phone” on
page 39, “Security for Your Phone and Subscription” on page 58,
“Calling Card Calls” on page 79 and “Accessories” on page 90.
If you change a setting which is included in a certain profile, the profile is
updated. With the Reset Profiles function, you can change all profile settings
back to the way they were set when you bought your phone.
To reset the profile settings
•
Scroll to Settings, Y E S , Profiles, Y E S , Reset Profiles, Y E S .
The profile settings are reset.
The Profile Concept
89
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Accessories
By using your T28 WORLD together with Ericsson original accessories, you
have access to a large range of useful features, in addition to those you have
when the phone is used separately.
•
Automatic divert of incoming calls when the phone is placed in a desktop
charger
•
Portable handsfree calling
•
Handsfree calling in your car
•
Infrared communication between your phone and computer
Note! This is one condition that the specific accessories exist in your market.
The Profiles concept, see “The Profile Concept” on page 87, allows you to
instruct your phone to activate a specific profile automatically when used
together with a certain accessory. On the following pages you can find
information on how different accessories interact with your phone and its
different profiles.
Note! You are informed of the current profile when you slide the volume key
upwards or downwards in standby mode or when you choose another profile.
Every time you disconnect your phone from the accessory, the profile is
changed to the one which was active before, if the current profile was
activated automatically.
For the profiles linked with an accessory to change automatically, the
automatic activation must be on. When you buy your phone, the automatic
activation is set to On for the Vehicle and Portable handsfree units. If you
wish, you may turn it off.
To turn automatic activation on or off
1. Scroll to Settings, Y E S , Profiles, Y E S , Auto Activation, Y E S .
2. Select On or Off.
Note! You can always choose a profile manually, even if a profile has been
activated automatically. See “The Profiles” on page 87.
90
Accessories
AB
Desktop Charger
If you use the T28 WORLD with a specific Ericsson Desktop Charger you
have access to some useful features besides ordinary charging. You can
choose to make the phone switch to the Home profile automatically and divert
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
all calls to your home number when you place your phone in the charger.
To be able to use these features, you need to make some settings the first time
you place your phone in the desktop charger.
Placing the Phone in the Desktop Charger
1. Place the phone in the desktop
charger as shown and press
backwards to attach the phone.
2. Pull the phone towards you and
upwards to detach the phone
from the charger.
Note! For further instructions on how to connect the desktop charger, please
contact your local Ericsson retailer.
To link the desktop charger with a profile and a divert number
1. Place the phone in the desktop charger. The message Choose profile? appears
in the display.
2. Press Y E S . (If you press N O , the desktop charger will not be linked with
any profile).
3. Select a profile that you want to link with the desktop charger, for example
the Home profile.
4. The message Divert when connected to accessory? appears. Press Y E S .
This means that you want to divert your calls to your home number when,
for example, you place the phone in the desktop charger.
(If you press N O , your calls will not be diverted).
Accessories
91
number) and press Y E S .
AB
5. Enter a phone number including the area code (for example, your home
A number you used before may be suggested to you. If so, press Y E S to
choose the number, or enter another number.
6. The message Automatic activation on? appears. Press Y E S .
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
The message Profile: Home appears to confirm your choice.
You can also make these settings later, if you wish. In this case, you need to
add the desktop charger to the Home profile, or another profile. See “To add
an accessory to a profile” on page 96. You may set the divert number in the
Edit Profile sub-menu, where all profile settings are included (Settings, Y E S ,
Profiles, Y E S , Edit Profile, Y E S ). See “Changing the profile settings” on page 88.
Note! The phone must be switched on and the automatic activation must be on
for the phone to switch profile automatically when connected to an accessory.
Tip! If you have several desktop chargers, they can each be added to a profile
or they can all be added to the same profile.
Portable Handsfree
When you connect a specific Ericsson Portable Handsfree to the
T28 WORLD, the Port H-free profile is set automatically. This means that all
profile settings are set to the values specified for the Port H-free profile.
See “The Profile Concept” on page 87.
Tip! If you do not want your phone to switch profile automatically when you
connect it to the Portable Handsfree, you need to turn the Auto activation
off. To do this, manually select the Port H-free profile, and set the Auto
activation to off.
Using the Portable Handsfree
To answer an incoming call
•
When the phone rings, press the button on your Portable Handsfree once.
Tip! You can also answer a call by using your voice. See “Voice Answering”
on page 78.
To end a call
•
Press the button on your Portable Handsfree once.
If the Call Waiting service is on, see “The Call Waiting Service” on page 65,
you can answer a second call by pressing the button on your Portable Handsfree.
92
Accessories
To answer a second call
Press the button on your Portable Handsfree once to answer the waiting call.
AB
•
The current call is now put on hold.
When you press the button on your Portable Handsfree again, the second
call is disconnected and the first call is retrieved automatically.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
To voice dial using the Portable Handsfree
1. Press and hold the button on your Portable Handsfree until you hear a tone.
2. Release the button and say a name (voice label) that you have recorded
previously.
The name is played back to you and the call is connected.
Note! Before you can use voice dialing, you need to record voice labels for
entries in your phone book. See “Preparing your Phone for Voice Dialing” on
page 76.
For best performance when voice dialing and voice answering with a
Portable Handsfree unit, we recommend recording your voice labels when
connected to a Portable Handsfree unit.
Vehicle Handsfree
When you connect an Ericsson Advanced Vehicle Handsfree to the
T28 WORLD, the In Car profile is set automatically. This means that all
profile settings are set to the values specified for the In Car profile.
See “The Profile Concept” on page 87.
Placing the Phone in the Vehicle Handsfree
1. Place the phone in the
holder as shown and press
backwards to attach it.
2. Press the button on top
of the holder to release
the phone.
Accessories
93
Tip! If you do not want your phone to switch profile automatically when you
AB
connect it to the Advanced Vehicle Handsfree, you need to turn the Auto
Activation off. To do this, manually select the In Car profile and set the Auto
Activation to Off.
Note! Your Advanced Vehicle Handsfree should be installed by professional
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
personnel. For more information, please contact your local Ericsson retailer.
Voice Control
The Advanced Vehicle handsfree unit is equipped with its own voice control
system which allows you to:
•
voice dial - call someone by simply saying the name
•
answer and reject calls using your voice
Before you can use voice dialing, you need to record voice labels to entries
in your phone book and the Voice Dialing function needs to be on.
See “Preparing your Phone for Voice Dialing” on page 76. To use voice
dialing with the Vehicle Handsfree unit, you need to record the voice labels in
the car. Voice labels for phone book entries recorded in the phone will not be
available in the car, and vice versa.
The vehicle handsfree can store up to 100 voice labels. The icons for the
phone book entries with voice labels saved when connected to a vehicle
handsfree kit look slightly different from those that you save in the phone,
see margin.
To voice dial using the Vehicle Handsfree
1. Slide and hold the volume key (when the flip is closed) or press Y E S until
you hear a tone.
2. Release and say a name (voice label) that you recorded in the car earlier.
(Use the microphone of the Vehicle Handsfree unit.)
The name is played back to you, and the call is connected.
To answer a call using your voice
•
See “Voice Answering” on page 78.
Handsfree Types
If you use a Vehicle Handsfree Unit, you can choose between two
different ways in which your phone can handle speech. This is done in
the Handsfree sub-menu.
94
Accessories
Basic Handsfree
AB
Basic Handsfree means that the phone handles the call in semi-duplex mode.
This means that you cannot speak at the same time as the person at the
other end of the line. Use this alternative only if Full Handsfree does not
work properly.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Full Handsfree
Full Handsfree means that the phone handles the call in full duplex mode.
This considerably increases the quality of speech, since you do not have to
wait until it is your turn to speak.
For Full Handsfree to work properly, your phone adapts to the sound
environment around the handsfree equipment. This adaptation might take a
few calls. During this learning phase, the person you are talking to might hear
an echo of his or her own voice (because the sound goes from the speaker into
the microphone again). However, this disappears as the other person speaks.
If the echo lasts longer than the first few calls, try Basic Handsfree instead.
Tip! Set the handsfree type to Full Handsfree first. If speech quality is poor,
set the Basic Handsfree type instead.
To set the handsfree type
1. Scroll to Settings, Y E S , Handsfree, Y E S , Handsfree Type, Y E S .
2. Select the type you want.
Answering Mode
When using a Portable or Vehicle Handsfree unit, you may choose to answer
incoming calls with Any Key or Auto.
•
Any Key: If you use the phone with handsfree equipment and this function
is turned on, you can answer an incoming call by pressing any key, except
the N O key.
•
Auto: If you choose the automatic answering mode, an incoming call is
answered automatically after one ring signal, if the phone is used with
handsfree equipment.
To set an answering mode
1. Scroll to Settings, Y E S , Handsfree, Y E S , Answering Mode, Y E S .
2. Select a mode.
If you choose the Normal alternative, you have to answer calls as normal.
Tip! You can also answer calls by using the Voice Answering function.
See “Voice Answering” on page 78.
Accessories
95
AB
Infrared modem
With an Ericsson infrared modem you can connect your T28 WORLD to a
computer via an infrared link. This makes the cable and PC card obsolete.
If you want to use the infrared modem
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
with a computer that is running
Windows 95/98/NT 4.0, you can install
PC software which allows you to
manage the phone book in your mobile
phone, send and receive SMS messages,
fax and data calls, edit your mobile
phone’s settings, browse the Internet or
connect to your corporate network.
When you have connected the infrared modem to the phone, an icon appears
in the display.
Note! For more information, please contact your local Ericsson retailer.
Adding Accessories to a Profile
You can add one or more accessories to a profile. For example, if you usually
use a portable handsfree together with a specific desktop charger, you can add
the desktop charger to the Port H-free profile. The phone recognizes the first
accessory when it is connected and switches profile automatically.
Note! Only profiles linked with accessories can be activated automatically.
Apart from the desktop charger and the portable and vehicle handsfree units,
you can also add an infrared modem to a profile.
Before you can add an accessory to a profile, you must choose the profile
manually to which you want to add the accessory. See “To select a profile
manually” on page 88.
To add an accessory to a profile
1. Scroll to Settings, Y E S , Profiles, Y E S , Accessories, Y E S .
Now you are in the list of the accessories which have already been added
to the profile.
2. Select Add accessory?.
Now you are in the list of all accessories that you can add to the profile.
3. Select an accessory.
4. The question Automatic activation on? appears, if automatic activation is not
on already.
96
Accessories
Press Y E S to turn automatic activation on, which means that the profile
AB
will be chosen automatically when the accessory is connected.
Note! In addition to the portable and vehicle handsfree units, you can add
another 12 accessories to a profile. Any accessory above this number will
work as ordinary non-profile accessories. You cannot have the same
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
accessory linked with several profiles.
To remove an accessory from a profile
1. Scroll to Settings, Y E S , Profiles, Y E S , Accessories, Y E S .
2. Scroll to the accessory that you want to remove and press C .
3. Delete? appears. Press Y E S .
Accessories
97
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Online Services
Imagine that you hear about a new service that your network operator is
offering. You call your operator, explain that you want to subscribe to the
service and suddenly, within seconds, you have a new menu in your phone
that instantly lets you use the new service.
You do not need upgraded software for your phone, but you may need to visit
your network operator to get a new SIM card. The rest is all taken care of over
the air.
This is just one example of the added value services that are made possible
through the ‘Online Services’.
Note! The T28 WORLD does not support all services offered by the
Online Services.
What is Online Services?
The Online Services is the network operators’ way of offering customized
services, independently of mobile phones and mobile phone manufacturers.
Compatibility
Added value services based on the Online Services require two things in order
to work:
•
a mobile phone that supports the Online Services. Your Ericsson
T28 WORLD is such a phone.
•
a network operator offering the Online Services.
Note! The Online Services on the SIM are designed and run by network
operators and not by mobile phone manufacturers. If you require further
information about the Online Services, please contact your network operator.
98
Online Services
AB
New Menu
A SIM card which supports the Online Services works in the same way as a
normal SIM card.
When you have inserted your SIM card and turned on your phone, your
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
network operator may download data to your SIM card. After the first data
download and after restarting your phone, the proactive SIM offers a new
menu in the phone. The menu offers you new features and services, which can
be used instantly.
On your T28 WORLD, this menu appears under the Extras menu. There can
only be one new sub-menu entry under the main menu, but there can be
several sub-menus under the new sub-menu entry.
To enter your new menu system
1. Scroll to Extras, Y E S , Online Services, Y E S .
If any sub-menus appear, select the one that you want and press Y E S .
2. Press N O to go back to the standby menu.
Note! Some operators may not use the name Online Services for this menu.
Please consult your network operator for more information.
Proactive SIM
The Online Services provides a proactive SIM. This means that the SIM can
tell the phone to take certain actions. These actions could include:
•
showing text from the SIM in the phone’s display
•
setting up a call to a number on the SIM
•
initiating a dialogue with the user
Note! All these actions are taken by the SIM card and, consequently, they have
nothing to do with the phone’s software.
Data Download to the SIM over the Air
Your network operator may at any time download new data to your SIM card
over the air. This new data could consist of new features or a new menu.
Resetting your SIM Card
When the operator updates your SIM card over the air, the phone notifies you
by showing a message in your display. You also hear a beep.
Online Services
99
phone and then turn it on again.
AB
In order for your new SIM settings to take effect, you have to turn off your
Note! After a data download the phone may not work and you will not be able
to use it until you restart it. This feature is operator dependent and will
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
probably not happen very often.
SIM Card Initiated Features
The SIM card may prompt you to make a call. This could happen even if you
are already engaged in a call.
When this happens, the phone will notify you by producing a sound and
showing a message in the display.
•
If you are not engaged in a call, a message is shown in the display, asking
you whether you want to confirm and make the SIM card initiated call.
•
•
If you want to make the SIM card initiated call, press Y E S .
•
If you do not want to make the SIM card initiated call, press N O .
If you are already engaged in a call, you are asked either to put the current
call on hold or to end it.
A message appears in the display, asking you whether you want to confirm
and make the SIM card initiated call.
•
If you want to make the SIM card initiated call, press Y E S .
•
If you do not want to make the SIM card initiated call, (you may want
to continue with the ongoing call) press N O .
Send a SIM Card Initiated SMS
The SIM card may set up an SMS (text message) and ask you to send this
message, for example by the question Send now?. Press Y E S if you want to
send the SMS.
Details of Services Offered
All services and functions that come with the Online Services are network
dependent. Please contact your network operator for details of services offered
by the Online Services.
100
Online Services
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Additional Information
Quick Keys
102
Troubleshooting
104
Ericsson Mobile Internet
106
Technical Data
107
Glossary
108
Guidelines for Safe and Efficient Use
113
Limited Warranty
119
Declaration of Conformity
121
Index
123
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Quick Keys
Several keys on your phone can be used to optimize the phone’s functionality
and decrease the number of times you need to press a key. Some of the key
combinations demand that your phone is in a certain mode and some can be
made from the standby mode.
The table describes some of the most useful key combinations.
To...
Mode:
press Y E S
when in standby
voice dial
press and hold Y E S
when in standby
voice dial
slide and hold the volume
key upwards or downwards
when in standby and
when the flip is open
call your Voice Mail
enter the Call log
102
Do this:
press and hold 1
when in standby
enter the + sign to make press and hold 0
an international phone call
when in standby
set the phone silent
press and hold C
when in standby
mute the microphone
press and hold down C
during a call
reach a phone book entry press the position number
and #
when in standby
reach a phone book
entry beginning with a
specific letter
press and hold any of the
keys 2 -9
when in standby
speed dial
press any of the number
keys 1 -9 and Y E S
when in standby
enter Find and Call
press and hold d
when in standby
put a call on hold
press Y E S
during a call
retrieve a call
press Y E S again
during a call
reject a call
quickly slide the volume key when receiving a call
upwards or downwards twice
enter the menu system
press u or d
when in standby
move through menus
or lists
slide (and hold) the volume
key upwards or downwards
when in the menus
select a menu or setting
press Y E S
when in the menus
delete an item
press and hold C
when in lists
go back to standby
press and hold N O
when in the menus
Quick Keys
Do this:
Mode:
enter the first sub-menu
of the My Shortcuts
menu
press and hold u
when in standby
AB
To...
when in standby
change the language to
press u 8888 d
when in standby
press u 0000 d
when in standby
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
find out which profile you slide the volume key
are using
upwards or downwards
Automatic
change the language to
Emergency (US)
reach the second letter or slide the volume key
character of a key
upwards and press any of
the number keys
when entering letters
reach the third letter or
character of a key
slide the volume key
downwards and press
any of the number keys
when entering letters
change between lowerand upper-case letters
press and hold *
when entering letters
enter numbers
press and hold any of the
number keys
when entering letters
enter a space
press 1 once
when entering letters
enter a question mark
slide the volume key
downwards and press 1
when entering letters
enter the @ -sign
slide the volume key
downwards and press 0
when entering letters
enter a p (pause)
press and hold *
when saving codes
delete letters and
numbers
press C
when entering letters
and numbers
A quick way to move through the menus is to use shortcuts. You simply enter
the number of the menu or sub-menu to which you want to go. See “Using
Shortcuts” on page 23 and “To set the key sound” on page 24.
To quickly and easily reach the settings you use most, you can place your
favorite settings in the menu My Shortcuts. See “My Shortcuts” on page 25.
For more information about key functions, see “Key Functions” on page 12,
“Moving through the Menus” on page 23 and “Entering Letters” on page 28.
Quick Keys
103
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Troubleshooting
This chapter lists some problems that you might encounter while using your
phone. Some problems require that you call your service provider, but most of
the problems you encounter are easy to correct yourself.
Error Messages
Insert Card
Insert card
There is no SIM card in the phone or you may have inserted it incorrectly.
Insert a SIM card. See “The SIM Card” on page 5.
Insert Correct Card
Insert correct card
The phone is set to only work with certain SIM cards. Insert the correct SIM card.
Emergency Calls Only
You are within range of a network but you are not allowed to use it.
Emergency calls
only
However, in an emergency, some operators allow you to call the emergency
number 911. See “Making Emergency Calls” on page 15.
No Network
No network
There is no network within range or the received signal is too weak. You have
to move to get a signal that is strong enough.
Wrong PIN, Wrong PIN2
You have entered your PIN or PIN2 incorrectly.
Wrong PIN
•
Enter the correct PIN or PIN2, and press Y E S .
See “The SIM Card Lock” on page 58.
Codes do not match
When you want to change a security code (for example your PIN) you have to
Codes do not
match
confirm the new code by entering it again. The two codes that you have
entered do not match. See “The SIM Card Lock” on page 58.
PIN/PIN2 Blocked
PIN blocked
You have entered your PIN or PIN2 incorrectly three times in a row.
To unblock, see “The SIM Card Lock” on page 58.
Blocked Contact Operator
Blocked
Contact operator
104
You entered your personal unblocking key code (PUK) incorrectly 10 times in
a row. Contact your network provider or service operator.
Troubleshooting
Phone Locked
The phone is locked. To unlock the phone, see “The Phone Lock” on page 59.
Phone Lock Code:
Phone lock code:
AB
Phone locked
Your phone comes with the phone lock code, 0000. You can change it to any
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
four-to eight-digit code. See “The Phone Lock” on page 59.
Number not Permitted
Number not
permitted
The Fixed Dialing function is on and the number you have dialed is not part
of your fixed numbers list. See “Fixed Dialing” on page 61.
Alien Battery - Slow Charging Only
Alien battery Slow charging only
The battery you are using is not an Ericsson-approved battery and is charging
slowly for safety reasons.
The Phone Cannot Be Switched on
Handheld Phone
•
Recharge or replace the battery. See “The Battery” on page 6.
Handsfree Phone in Vehicle
•
Make sure that the phone is properly inserted into its holder. See “Vehicle
Handsfree” on page 93.
Other Problems
No Indication of Charging
When you start charging a battery that is empty or a battery that has not been
used for a long time, it may take a while until the indicator on the top of the
phone shows a red light and the battery meter appears.
No Indication of Missed Calls
To be able to see if you have missed a call, the Call Log must be on.
Troubleshooting
105
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
AB
Ericsson Mobile Internet
When you are on the move and in need of communication and information,
the Mobile Internet is the answer.
The Mobile Internet is a service supplied by Ericsson to make it easier for you
to communicate and receive information quickly, wherever you are. It gives
you access to various messaging services, on-line customer services, user
manuals and other useful information. With the Mobile Internet you can also
download communications software to ensure you get the best out of your
Ericsson products.
The Ericsson Mobile Internet address is
http://mobileinternet.ericsson.com
106
Ericsson Mobile Internet
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Technical Data
General
Product name
T28 WORLD
System
GSM 900/GSM1900
SIM card
Small plug-in card, 3V or 5V type
Type number
114 1101-BV
Dimensions
Size
95 x 49 x 15 mm
Weight with Ultra Slim battery
83g
Weight without battery
60g
Humidity
Ambient temperatures
Max
131°F (+55°C)
Min
14°F (-10°C)
Technical Data
107
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Glossary
Advice of Charge (AoC)
enables you to monitor the cost of calls made from your mobile phone.
Details of the last call and total calls made are shown in the phone display.
To use this service, it must be supported by your network.
Area Information (AI)
is a service that allows you to receive messages about pre-set topics i.e.
weather forecasts, road reports, etc. To use this service, it must be supported
by your network.
Calling Line Identification (CLI)
shows the number of the person calling you in your mobile phone display.
You can then make an informed choice as to whether or not to take the call.
Bear in mind that not all numbers can be displayed. To use this service, it must
be supported by your network.
Divert
enables you to forward calls to another number, for example your voice mail
or home phone.
DTMF or Touch Tone
Dual Tone Multi Frequency signal – codes sent as tone signals.
Used for telephone banking, for accessing an answering machine, etc.
Dual Band GSM 900/1900
The Ericsson T28 WORLD is a dual band phone, which means that you can
use your phone on two different kinds of networks – the GSM 900 and the
GSM 1900 systems.
The switching between the two systems is down automatically at initial
power up. When you turn on the phone, the phone automatically scans the
network to identify if it is a GSM900 or a GSM1900 network.
The difference compared to Ericssons GSM900/1800 phones is that the
T28 WORLD does not provide seamless handover during conversation.
Seamless handover is not a useful feature in this dual band product since there
are no networks in the world that are GSM900/1900 systems.
108
Glossary
is used for keying in letters or numbers from the keypad.
Fax Class
AB
Enter
Standards for fax transmission are set as classes. Class I and II allow data
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
transfer speeds of between 2400 up to 9600 bps.
Fixed Numbers
enables you to allow only numbers beginning with certain pre-defined figures
to be dialed from your mobile phone. The service is protected by your PIN2.
To use this service, it must be supported by your network.
Full Duplex
in handsfree equipment, means that both parties on the phone can talk at the
same time. The opposite is simplex mode when one party talks and the other
must wait for his/her turn.
GSM 900
GSM is the world’s most widely-used digital network, now operating in over
100 countries around the world, particularly in Europe and Asia-Pacific.
The Global System for Mobile Communications is the most-widely used
digital mobile phone system. The GSM systems family also includes
GSM 1800 and GSM 1900. There are different phases of roll-out for the
GSM system and GSM phones are either phase 1 or phase 2 compliant.
GSM 1900
is a digital network working on a frequency of 1900 MHz. It is used in
the Americas.
International (+) sign
mobile phone (+) sign that automatically adds the correct international code in
front of a telephone number when dialing out of a country. You then have to
enter the code of the country you are calling.
International Roaming
a mobile phone feature that allows you to switch between networks offering
coverage abroad. Your mobile phone automatically selects a network or
system (your home network), but if it is not in range or unavailable, it selects
another system. International roaming is based on agreements between
network operators in different countries.
Glossary
109
see Two Line Service.
Menu System
AB
Line 1/Line 2
is where you can access all the phone’s functions. The menus can be accessed
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
and viewed by scrolling with the arrow keys.
Network
a mobile phone network or system consists of a network of cells or areas.
A radio base station serves each cell from where calls are forwarded to and
received from your mobile phone by wireless radio signals.
Network Operator
to be able to use your phone, you need a subscription to a network.
You get this subscription from a network operator, together with a SIM card
that you need to use with your phone.
PC-Card
also called PCMCIA, the PC-card can act as a modem and connect your
mobile phone to a laptop or organizer, enabling data and fax transmission.
The thin type II card is the most common size.
Phone Book
a memory in your mobile phone or SIM card where phone numbers can be
stored and accessed alphabetically or by position.
PIN
Personal Identification Number – a code used for all GSM-based phones to
establish authorization for access to certain functions or information.
The PIN code comes with your subscription.
PIN2
Personal Identification Number 2 – an authorization code which is used only
for special services. The PIN2 code comes with your subscription.
PUK
Personal Unblocking Key Code – used to unlock a blocked SIM card.
This comes with your subscription.
110
Glossary
Restrict Calls
AB
enables you to restrict or block certain or all types of calls to and from your
mobile phone, i.e. outgoing calls, outgoing international calls, incoming calls.
Blocking is switched on with a personal code. To use this service, it must be
supported by your network.
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Roaming
Within your home network, this means that your mobile phone automatically
sets up communication procedures with different radio base stations when
on the move.
Scroll
move between the menus and functions by pressing u or d.
Select
choose a menu or function by pressing the Y E S key.
Semi-Duplex
In handsfree equipment, full duplex means that the connection is open for
both parties to talk simultaneously. The opposite, simplex, is when it is open
to one at a time. Semi-duplex gives close to, but not complete, duplex
functionality.
Service Provider
a company that provides services and subscriptions to mobile phone users.
Short Message Service (SMS)
allows messages of up to 160 characters to be sent and received via the
network operator’s message center to your mobile phone. Messages are stored
if the phone is off or out of reach ensuring that they reach you. To use this
service, it must be supported by your network.
SIM card
Subscriber Identity Module card – a card that must be inserted in any GSMbased mobile phone. It contains subscriber details, security information and
memory for a personal directory of numbers. The card can be a small plug-in
type or credit card sized but both types have the same functions.
The T28 WORLD uses the small plug-in card.
Glossary
111
Subscription
AB
is the contract that you have with the service/network provider. To use your
phone, you need to have a subscription to a network. You get a SIM
(Subscriber Identity Module) card with your subscription. The services
included in your subscription depend on your choice of operator and/or
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
subscription. So some of the services and functions described in this manual
may not be accessible to you. If you want a complete list of the services
included in your subscription, please contact your network operator.
Two Line Service
enables you to have two lines and two different phone numbers on one
subscription for your mobile phone. This makes it possible to have separate
numbers for business and personal calls. To use this service, it must be
supported by your network.
112
Glossary
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Guidelines for Safe
and Efficient Use
Note! Read this information before using your mobile phone.
Product Care and Maintenance
Your mobile phone is a highly sophisticated electronic device. To get the most out
of your mobile phone read this text about product care, safe and efficient use.
Product Care
•
Keep your mobile phone dry.
•
Avoid exposing your mobile phone to extreme hot or cold temperatures.
•
Avoid placing your mobile phone close to lit candles, cigarettes,
naked flames or any heat source.
•
As with all sophisticated electronic devices rough treatment could damage
your mobile phone.
•
Only use a soft damp cloth to clean your mobile phone.
•
Do not paint your mobile phone as the paint could obstruct the earphone,
microphone or any moveable parts and prevent normal use.
•
Do not attempt to disassemble your mobile phone, a broken warranty seal
will void the warranty. The phone does not contain consumer serviceable
components. Service should only be performed by Certified
Service Partners.
•
Only use Ericsson original accessories. Failure to do so may result in loss
of performance, damage to the phone, fire, electric shock or injury.
The warranty does not cover product failures which have been caused by
use of non-Ericsson original accessories.
•
Treat your mobile phone with care, keep it in a clean and dust free place.
Guidelines for Safe and Efficient Use
113
To avoid impaired performance please ensure your mobile phone’s
antenna is not bent or damaged.
•
AB
Antenna Care and Replacement
•
Do not remove the antenna yourself. If your phone’s antenna is damaged
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
please take it to a Certified Service Partner.
•
Only use an antenna that has been specifically designed for your phone.
Unauthorized antennas, modifications, or attachments could damage the
phone and may violate the appropriate regulations causing loss
of performance and radio frequency (RF) energy above the
recommended limits.
Efficient Phone Operation
To enjoy optimum performance with minimum power consumption please:
•
Hold the phone as you would any other telephone. While speaking directly
into the mouthpiece, angle the antenna in a direction up and over your
shoulder. If the antenna is extendable/retractable, it should be extended
during a call.
•
Do not hold the antenna when the phone is in use. Holding the antenna
affects call quality, may cause the phone to operate at a higher power level
than needed and shorten talk and standby times. If your mobile phone is
equipped with an infrared eye, never direct the infrared ray at anyone’s eye
and make sure that it does not disturb any other infrared units.
Radio Frequency Energy
Your mobile phone is a radio transmitter and receiver. When the phone is
turned on, it receives and transmits radio frequency (RF) energy. Depending
on the type of mobile phone you possess, it operates on different frequency
ranges and employs commonly used modulation techniques. The system that
handles your call when you are using your phone controls the power level at
which your phone transmits.
114
Guidelines for Safe and Efficient Use
AB
Exposure to Radio Frequency Energy
The International Commission on Non-Ionising Radiation Protection
(ICNIRP), supported by the World Health Organisation (WHO), published
during1996 a statement and in 1998 guidelines which set recommended limits
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
for exposure to RF fields from handheld mobile telephones. According to
ICNIRP statement, which is based on the available body of research, there is
no evidence that mobile terminals meeting the recommended limits can cause
any adverse health effects. All Ericsson telephones conform to the ICNIRP
guidelines and other international exposure standards, such as:
•
CENELEC European Pre-standard ENV50166-2:1995 (Europe)
•
ANSI/IEEE C95.1-1992 (USA, Asia-Pacific)
•
AS/NZS 2772.1 (Int):1998 (Australia, New Zealand)
Driving
Check the laws and regulations on the use of mobile phones in the areas where
you drive. If you are going to use your phone while driving, please:
•
Give full attention to driving.
•
Use an Ericsson Vehicle Handsfree Solution, if available. Law in many
countries requires vehicle Handsfree Solution. Read the installation
instructions carefully before installing a vehicle Handsfree Solution.
•
Pull off the road and park before making or answering a call if driving
conditions so require.
RF energy may affect some electronic systems in motor vehicles such as car
stereo, safety equipment etc. In addition, some vehicle manufacturers do not
allow use of mobile phones, unless the installation is supported by a handsfree
kit with an external antenna, in their vehicles. Check with your vehicle
manufacturer’s representative to be sure that your mobile phone will not affect
the electronic systems in your vehicle.
Vehicles Equipped with an Air Bag
An air bag inflates with great force. Do not place objects, including either
installed or portable wireless equipment, in the area over the air bag or in the
air bag deployment area. If in-vehicle wireless equipment is improperly
installed and the air bag inflates, serious injury could result.
Guidelines for Safe and Efficient Use
115
AB
Electronic Devices
Most modern electronic equipment, for example equipment in hospitals and
cars, is shielded from RF energy. However, certain electronic equipment is
not, therefore:
Do not use your mobile phone near medical equipment without requesting
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
•
permission.
Mobile phones may affect the operation of some implanted cardiac
pacemakers and other medically implanted equipment. Pacemaker patients
should be aware that the use of a mobile phone very close to a pacemaker
might cause the device to malfunction. Avoid placing the phone over the
pacemaker, i.e. in your breast pocket. When using the phone, place it at your
ear opposite the pacemaker. If a minimum distance of 15 cm is kept between
the phone and the pacemaker, the risk of interference is limited. If you have
any reason to suspect that interference is taking place, immediately turn off
your phone.
Contact your cardiologist for more information.
Some hearing aids might be disturbed by mobile phones. In the event of such
disturbance, you may want to consult your service provider, or call the
customer services line to discuss alternatives.
Aircraft
•
Turn off your mobile phone before boarding any aircraft.
•
Do not use it on the ground without crew permission.
To prevent interference with communication systems, you must not use your
mobile phone while the plane is in the air.
Blasting Areas
Turn off your mobile phone when in a blasting area or in areas posted “turn off
two-way radio” to avoid interfering with blasting operations. Construction
crews often use remote control RF devices to set off explosives.
116
Guidelines for Safe and Efficient Use
AB
Potentially Explosive Atmospheres
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Turn off your mobile phone when in any area with a potentially explosive
atmosphere. It is rare, but your phone or its accessories could generate sparks.
Sparks in such areas could cause an explosion or fire resulting in bodily injury
or even death.
Areas with potentially explosive atmospheres are often, but not always,
clearly marked. They include fuelling areas, such as gas stations, below deck
on ships, fuel or chemical transfer or storage facilities, and areas where the air
contains chemicals or particles, such as grain, dust, or metal powders.
Do not transport or store flammable gas, liquid, or explosives in the
compartment of your vehicle, which contains your mobile phone and
accessories.
Power Supply
•
•
•
•
•
Connect AC (Power supply) only to designated power sources as marked
on the product.
To reduce risk of damage to the electric cord, remove it from the outlet by
holding onto the AC adapter rather than the cord.
Make sure the cord is positioned so that it will not be stepped on, tripped
over or otherwise subjected to damage or stress.
To reduce risk of electric shock, unplug the unit from any power source
before attempting to clean it.
The charger must not be used outdoors or in damp areas.
Children
Do not allow children to play with your mobile phone since it contains small
parts that could become detached and create a choking hazard.
Emergency Calls
IMPORTANT!
This phone, like any mobile phone, operates using radio signals, cellular and
landline networks as well as user-programmed functions, which cannot
guarantee connection under all conditions. You should therefore never rely
solely upon any mobile phone for essential communications (e.g. medical
emergencies).
Keep in mind that, in order to make or receive calls, the phone must be
switched on and be located in a service area with adequate cellular signal
strength. Emergency calls may not be possible on all mobile phone networks
or when certain network services and/or phone features are in use. Check with
your local service provider.
Guidelines for Safe and Efficient Use
117
The battery delivered with your phone is not fully charged.
Battery Use and Care
AB
Battery Information
New Batteries
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
A rechargeable battery has a long service life if treated properly. A new
battery, or one that has not been used for a long period of time could have
reduced capacity the first few times it is being used.
•
The talk and standby times depend on the actual transmission conditions
when using the phone. If the phone is used near a base station, less power
is required and talk and standby times are prolonged.
•
Use only batteries manufactured by Ericsson and the AC/DC adapter
supplied with your battery charger. Using accessories not manufactured by
Ericsson may be hazardous and the warranty does not cover product
failures caused by the use of non-Ericsson original accessories.
•
Do not expose your battery to extreme temperatures, never above
+60°C (+140°F).
•
For maximum battery capacity, use your battery at room temperature.
If the battery is used at low temperatures, the battery capacity will
be reduced.
•
The battery can only be charged when the temperature is between +5°C
(+41°F) and +45°C (+113°F).
•
Turn off your phone before removing the battery.
•
Use the battery only for its intended purpose.
•
Do not attempt to take the battery apart.
•
Do not let the metal contacts on the battery touch other metal objects.
This may short-circuit and damage the battery.
•
Do not expose a battery to open flames. This may cause the battery
to explode.
•
Do not expose a battery to liquids.
•
Never place the battery in your mouth. Battery electrolytes may be toxic if
swallowed.
Battery Recycling
Your phone manufacturer is a member of the Rechargeable Battery Recycling
Corporation (RBRC); a non-profit public service organization designed to
assist in the recycling of rechargeable batteries. Many areas require recycling
of rechargeable batteries. In the U.S., call 1-800-822-8837 for information on
how to recycle your battery. Outside the U.S., contact your local retailer for
recycling instructions.
118
Guidelines for Safe and Efficient Use
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Limited Warranty
Thank you for purchasing this Ericsson Product. For optimal benefit of your
new product’s features, we recommend that you follow a few simple steps:
•
Read the Guidelines for Safe and Efficient Use.
•
Read all the terms and conditions of your Ericsson Warranty.
•
Save your original receipt. You will need it for warranty repair claims.
If your Ericsson Product needs warranty service, please return it to the
dealer from whom it was purchased or contact your local Ericsson
helpdesk to get further information.
Our Warranty
Ericsson warrants this Product to be free from defects in material and
workmanship at the time of its original purchase by a consumer, and for a
subsequent period of one (1) year.
All accessories for the Product are covered by a warranty for a period of
one (1) year from the date of its original purchase by a consumer.
What We Will Do
If, during the warranty period, this Product fails to operate under normal use
and service, due to improper materials or workmanship, Ericsson subsidiaries,
authorized distributors or authorized service partners will, at their discretion,
either repair or replace the Product in accordance with the terms and
conditions stipulated
Limited Warranty
119
AB
Conditions
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
1. The warranty is valid only if the original receipt issued to the original
buyer by the dealer, specifying the date of purchase and serial number,
is presented with the product to be repaired or replaced. Ericsson reserves
the right to refuse warranty service if this information has been removed or
changed after the original purchase of the product from the dealer.
2. If Ericsson repairs or replaces the Product, the repaired or replaced
Product shall be warranted for the remaining time of the original warranty
period or for ninety (90) days from the date of repair, whichever is longer.
For repair or replacement, functionally equivalent reconditioned units may
be used. Replaced faulty parts or components will become the property of
Ericsson.
3. This warranty does not cover any Product failure due to normal wear and
tear, misuse, including but not limited to use in other than the normal and
customary manner, in accordance with Ericsson’s instructions for use and
maintenance of the Product, accidents, modification, or adjustment, acts of
God, improper ventilation and damage caused by liquids.
4. This warranty does not cover product failures due to repair installations,
modifications or improper service performed by a service workshop not
authorized by Ericsson or opening of the product by persons not
authorized by Ericsson.
5. The warranty does not cover product failures caused by the use of nonEricsson original accessories.
6. Tampering with any of the seals on the products will void the warranty.
7. THERE ARE NO OTHER EXPRESS WARRANTIES, WHETHER
WRITTEN OR ORAL, OTHER THAN THIS PRINTED LIMITED
WARRANTY. ALL IMPLIED WARRANTIES, INCLUDING
WITHOUT LIMITATION THE IMPLIED WARRANTIES FOR
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE,
ARE LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.
UNDER NO CIRCUMSTANCES SHALL ERICSSON BE HELD
LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF
ANY NATURE WHATSOEVER, INCLUDING BUT NOT LIMITED TO
LOST PROFITS OR COMMERCIAL LOSS, TO THE FULL EXTENT
THOSE DAMAGES CAN BE DISCLAIMED BY LAW.
Some states do not allow the exclusion or limitation of incidental or
consequential damage, or limitation of the duration of implied warranties,
so the preceding limitations or exclusions may not apply to you. This warranty
gives you specific legal rights, and you may also have other rights that may
vary from country to country.
120
Limited Warranty
Declaration
of Conformity
We, Ericsson Mobile Communications AB of
Nya Vattentornet
221 83 Lund, Sweden
declare under our sole responsibility that our product
Ericsson type 114 1101-BV
to which this declaration relates, conforms to the appropriate standards
TBR 19, TBR 20, NATWG .03, ETS 300 342-1 and EN 60950,
following the provisions of Teleterminals directive 91/263/EEC,
EMC directive 89/336/EEC, and Low voltage directive 73/23/EEC.
Stockholm January 17, 2000
(Place & date of issue)
/Johan Siberg/
Johan Siberg, President
Declaration of Conformity
121
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
122
Declaration of Conformity
AB
AB
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Index
A
Add accessories to a profile 96
Alarm 83
Alarm indicator 11
Alarm signal 42
Answered calls indicator 35
Answering calls 16
Answering mode 95
Answering service. See Voice Mail
Area information 54
message types 54
receiving area messages 55
Assembling the phone 5
B
Banking by phone 32
Battery 6
attaching 6
charging 6, 7
detaching 6
Bell. See Alarm indicator
Blocking calls. See Restrict calls
C
Calculator 84
Call blocking. See Restrict calls
Call cost 73
setting a credit limit 74
specifying price per unit 73
Call divert
activating 56
Call Log
calling from Call Log 35
using the Call Log 35
Call restrictions. See Restrict calls
Call Screening 63
Call time 73
Call waiting 65
Call waiting service
activating 65
cancelling 65
Calling
from Call Log 35
Calling card
making a call 80
saving number 79
Calling card services
activating 79
Calling Line Identification (CLI) 35
Calls
answering 12, 16
making 14
putting on hold 17, 65, 66, 68, 69
receiving 15
redialing 14
rejecting 16
switching between calls 66
CB. See Area information
Cell broadcast. See Area information
Changing phone lines 75
Charging 6, 7
disconnecting the charger 8
Choosing a card 80
Clock. See Time
Closed user groups 62
Conference calls 67
adding new participants 68
creating 67
extracting a participant 68
releasing a participant 68
reviewing participants 68
Credit card
making a call 80
saving number 79
Index
123
H
Date 45
format 45
setting 45
Desktop charger 91
Dialed numbers indicator 35
Disable caller ID 36
Display
greeting text 43
language 10, 43
light 43
Display information 11
Divert Calls 56
activating 56
checking status 57
divert indicator 11, 57
incoming calls 56
Divert calls
cancelling 57
Divert indicator 11, 57
DTMF tones 17
Dual Band 108
Handsfree usage 94
Help functions 25
I
AB
D
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Indicators in display 35
alarm 11
answered calls 35
battery meter 11
dialed numbers 35
divert 11
line 11
missed calls 11, 35
signal strength meter 11
silent ring 11
SMS 11
Infrared modem 96
Initial settings 10
International calls 15
K
Key functions 12
Keypad 4
E
Emergency calls 15
Emergency number 15
Enable caller ID 36
Error messages 104
F
Fax, sending and receiving 81
Features 20
Fixed dialing 61
activating 62
Fixed numbers 62
editing 62
storing 62
Flip 14, 69
G
Games 85
Glossary 108
Greeting text in the display 43
124
Index
L
Language in the display 10, 43
Letters, entering 28
Line
chosing a line 75
Line indicator 11
M
Making a call 14
Menu system 21
display text 24
moving through 23
shortcuts 25
Message signal 42
Message types (SMS) 49
Microphone
muting 17
Minute minder 42
Missed calls 36
Missed calls indicator 11, 35
Muting microphone 17
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
Name label 29
Network
forbidden networks 71
preferences 70
preferred networks 71
search modes 72
selecting 70
Note Pad 18
Profile
change name of 88
indicator 11
Profiles 87, 92
automatic activation 87
change settings 89
selecting 88
PUK 6, 58
AB
N
O
Online services 98
Overview 4
P
Personal ring signal 40
Phone book 27
checking status of memory 34
creating 27
edit a phone number 30
e-mail addresses 33
entering letters 28
erasing phone number 31
groups 33
international numbers 27
keeping up to date 30
memory 27
memory full 31
overwrite protection 31
shortcuts 30
Phone lock 59
activating/cancelling 60
auto lock 59
changing the security code 60
full lock 59
Phone number
displaying own 44
Phone number in SMS
replying to 51
PIN 5, 9
changing 58
PIN2 5
changing 59
Plus sign (+) 15
Portable handsfree 92
Preparing the phone 4
Q
Quick keys 102
R
Receive calls 15
Receiving messages (SMS) 50
Redialing numbers 14
Rejecting calls 16
Request reply (SMS) 49
Resetting phone 45
Restrict calls 60
cancelling all 61
changing password 61
changing status 60
Ring signal
choosing 40
composing own 41
personal 40
type 40
volume 39
S
Scroll 12
Sending messages (SMS) 47
Settings
initial 10
Silent ring signal 11
SIM
Application Toolkit 98
data download to 99
proactive 99
SIM card 5
features initiated by 100
inserting 5
resetting 99
unblocking 58
Index
125
AB
Voice control
answering 76, 78
dialing 76
labels 76
making calls 77
rejecting 76
Voice label 76
Voice mail 37
activating 37
calling 37
changing number 38
changing signal 38
Voice Mail indicator 11
Volume
changing 17
Volume keys 13, 16
Er
ics No
so t fo
nM r
ob Com
ile
me
Co
r
mm cial
un Use
ica
tio
ns
SIM card lock
activating 59
cancelling 59
unlocking 58
SMS 46
composing messages 47
deleting a message 52
editing messages 47
enabling phone for sending 46
forwarding messages 52
message types 48
reading stored messages 53
receiving messages 50
reply requested 49
replying to messages 52
sending messages 47
storing messages 52
templates 50
types 49
SMS indicator 11
Speed dialing 30
Stop watch 84
Stored messages (SMS)
reading 53
T
Technical data 107
Telephone banking 32
Text messages (SMS) 46
Time 44
format 44
setting 44
Timer 84
Tone signals 17
Touch tones 17
Troubleshooting 104
Turning your phone off 10
Turning your phone on 9
Two Line Service 75
V
Vehicle handsfree 93
Vibrate mode 41
Vibrating unit 41
126
Index
">