Lanzar VIBE VIBE1801D, VIBE VIBE3200D User Manual

Add to my manuals
15 Pages

advertisement

Lanzar VIBE VIBE1801D, VIBE VIBE3200D User Manual | Manualzz

T A B L E O F C O N T E N T S

1. Contents

2. Introduction

3. Features

4. Specifications

5. Amplifier installation

6.7. Features and controls

8.9.10.11. System wiring

12.13. Troubleshooting

V

I B E

O

W N E R ’ S

M

A N U A L — 1

I N T R O D U C T I O N

Thank you for purchasing the Lanzar VIBE Class-D amplifier. Rest assured you have purchased a quality product designed and engineered to give you many years of uncompromised musical service.

The VIBE Class-D amplifier has been designed using the latest in electronic technology available today.

This mono subwoofer amplifer is the result of advanced high speed switching technology that overcomes the less-efficient classAB design. The VIBE Class-D amplifier reflects your true appreciation for powerful bass and recording.

2

— V I B E O W N E R ’ S M A N U A L

CLASS-D DESIGN

Low - frequency information for subwoofer only.

High efficient power

POWER SUPPLIES

Stiffly regulated PWM power supplies.

MOSFET switches maintain rated power over a wide range of battery voltages.

LOW PASS FILTER

Adjustable from 50Hz to 150Hz with a slope of 24dB per octave.

This allows for the adjustment of the upper point of the frequency bandwidth and the respective subwoofer.

VARIABLE SUBSONIC FILTER

Adjustable from 15Hz to 40Hz (VIBE1801D) / 10Hz -40Hz (VIBE3200D) with a slope of 24dB per octave.

This allows for the attenuation of frequencies that are mostly inaudible and cause unnecessary strain on the amplifier.

PROTECTION CIRCUITRY

Protection against thermal, Overload and short circuit conditions.

REMOTE DASH-MOUNT GAIN CONTROL

This amplifier come complete with a compact remote GAIN CONTROLLER which can be conveniently mounted on or under the dashboard of your car.

F E A T U R E S

V I B E O W N E R ’ S M A N U A L — 3

S P E C I F I C A T I O N S

MODEL

RMS Power, INTO 4 Ohms

RMS Power, INTO 2 Ohms

RMS Power, INTO 1.3 Ohms

MAX Power, INTO 1.3 Ohms

BRIDGE MAX Power, INTO 2 Ohms

THD at 1 Watt, 4 Ohm

Signal-to-Noise Ratio, below rated power output

Frequency Response, at 1Watt,4 Ohm

Damping Factor at 20Hz, 4 Ohm

Low Pass Filter

Variable Subsonic Filter

Bass Boost

Phase Control

Input Sensitivity

Input Impedance

Line Output Impedance

Dimensions(Inches)

Fuse Rating

VIBE1801D mono channel amilifier

1X400W

1X800W

1X900W

1X1800W

1X3600W

0.5%

95

15Hz to 150Hz

300

50Hz ~ 150Hz

15Hz ~ 40Hz

0+18dB

0 to180

200mV to 8V

10K Ohm

100 Ohm

10.25”x2.36”x15.10”

40Ax4

VIBE3200D mono channel amilifier

1200W

2200W

2400W

3200W

6400W

0.5%

95

15Hz to 150Hz

300

50Hz ~ 150Hz, 24dB/Octave

10Hz ~ 40Hz, 24dB/Octave

0+18dB

0 to180

200mV to 8V

10K Ohm

100 Ohm

10.25”x2.36”x21.06”

250A (Not Included)

4

— V I B E O W N E R ’ S M A N U A L

A M P L I F I E R I N S T A L L A T I O N

1. Find a suitable location in the vehicle to mount the amplifier.

2. Make sure there is sufficient air flow around the intended mounting location.

3. Bolt the amplifier to the mounting surface.

4. Connect the power ground terminal to the nearest point on the chassis of the

car. Keep this ground wire less than one meter (39”) in length. Use 4 gauge wire.

5. Connect the remote terminal to the remote output of the head unit using 14 gauge.

6. Connect an empty fuse holder within 300mm (12”) of the battery and 4 gauge

or larger high quality cable from this fuse to the amplifier location.

7. Make sure there is no fuse in this fuse holder. Then make the connection to the “BATT”

connection on the amplifier.

8 If multiple amplifiers are being used, use cables (each with its own fuse at the battery)

or a #0 or a #2 cable from the fuse holder at the battery to a distribution

block at or near the amplifier’s location.

9 Connect all line inputs and outputs using high-quality RCA-RCA cables.

10. Insert fuse(s) at the battery fuse holder(s).

11. Recheck all connections before powering up.

12. Set all level controls to their least sensitive positions and set all crossover controls, switches,

etc. to the desired frequency or position.

13. Once the system is powered up , set the volume control on the head unit to about the

2 o’clock position, and then set all the amplifiers’ level controls for maximum output level.

14. Further fine tuning of the various controls may be necessary to obtain the desired results.

V I B E O W N E R ’ S M A N U A L — 5

F

E A T U R E S A N D

C

O N T R O L S

VIBE1801D

7

9

R

L

Line

Out

Line

Input

Level

Sub sonic

Low

Pass

Phase shift

Bass

Boost

Min Max 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18

PWR PROT

Master

Bridged

Slave

Mode

Data Link

SPEAKERS

+

9

1 2 3 4 5

6

6

7

10

8 9

VIBE3200D

PWR

L

Line

Out

R

Line

Input

L

Input

Level

Subsonic

Filter

LowPass

Filter

Bass

Boost

Min Max 10Hz 40Hz 50Hz 150Hz 0 18dB

PHASE

180°

Remote

R

Master Slave

Input sensitivity Bridged mode Data Link

PROT

10

6

— V I B E O W N E R ’ S M A N U A L

1 2 3 4 5

F E A T U R E S A N D C O N T R O L S

1. Line Out RCA Jacks The LINE OUT allows you to build multiple amplifier systems without having to use splitter cords to distribute the signal. Now it is simple a matter of bringing one set of RCAs into the first amplifier, then using the line out RCA jacks as the feed to the next amplifier.

2. Line Input RCA Jacks These inputs are for signal cables from the source.

Always use high quality shielded RCA cables.

3. Input Level Controls Enables the matching of input levels to the output levels from the head unit( or other signal source).

4. Variable Subsonic Filter - 15Hz~40Hz (VIBE1801D), 10Hz - 40Hz (VIBE3200D)

5. Low Pass Filter When Crossover Mode Selector is in Low Pass Mode, this control limits the frequencies which will be distributed to the speakers to those below the value to which this is set within the range 50Hz~150Hz.

6. Variable Bass Boost Control 0 ~ +18dB

7. Phase Shift Allows you to change the phase of your subwoofer from 0 to 180 degrees to help compensate for timing differences between drivers.

8. Bass Boost Remote Control Input

9.Power & Protection Indicators- Provde instant information on status of amplifier, including short-circuit and thermal overload alerts.

10. Brigde Mode

V I B E O W N E R ’ S M A N U A L — 7

S

Y S T M

W

I R I N G

SIGNAL INPUT AND BYPASS OUTPUT CONNECTION

R

L

Line

Out

Line

Input

Level

Sub sonic

Low

Pass

Phase shift

Bass

Boost

Min Max 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18

PWR PROT

Master

Bridged

Slave

Mode

Data Link

SPEAKERS

+

SUBWOOFER

SPEAKER IMPEDANCE 1~8 Ohm

(VIBE 0.8K-D:2~8Ohm)

TO SATELLITE AMPLIFIER

LINE-INPUT

SPEAKER OUTPUT CONNECTION

TO CAR STEREO LINE-OUT

VIBE1801D

POWER

Remote

40AX4 FUSES

+

12V

REM

GND

8

LEVEL

MIN

MAX to REMOTE GAIN CONTROLLER

V I B E O W N E R ’ S M A N U A L

BATTERY

TO CAR STEREO AUTO ANTENNA

SIGNAL INPUT AND BYPASS OUTPUT CONNECTION

PWR

L

Line

Out

R

Line

Input

Input

Level

Subsonic

Filter

LowPass

Filter

Bass

Boost

L

Min Max 10Hz 40Hz 50Hz 150Hz 0 18dB

PHASE

180°

Remote

R

Master Slave

Input sensitivity Bridged mode Data Link

PROT

TO SATELLITE AMPLIFIER

LINE-INPUT

TO CAR STEREO LINE-OUT

SPEAKER OUTPUT CONNECTION

LEVEL

MIN MAX

+ REM + 12V GND

SPEAKERS

SUBWOOFER

TO CAR STEREO AUTO ANTENNA

SPEAKER IMPEDANCE 1~8 Ohm

FUSE

BATTERY

POWER

CHASSIS GROUND

(BARE METAL)

S Y S T M W I R I N G

VIBE3200D

V I B E O W N E R ’ S M A N U A L — 9

S

Y S T E M

W

I R I N G

Master Slave

VIBE1801D

˄ BRIDGED SWITCH ; MASTER POSITION ˅

R

L

Line

Out

Line

Input

Level

Sub sonic

Low

Pass

Phase shift

Bass

Boost

Min Max 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18

PWR PROT

SPEAKERS

+

Master

Bridged

Slave

Mode

Data Link

to INPUTS OF

SATELLITE AMPLIFIER

from OUTPUTS of

HEAD UNIT

+

-

SUBWOOFR

SPEAKER IMPEDANCE

4-8 OHMS ʽ

R

L

Line

Out

Line

Input

Level

Sub sonic

Low

Pass

Phase shift

Bass

Boost

Min Max 15Hz 40Hz 50Hz 150Hz 0° 180° 0 18

PWR PROT

Master

Bridged

Slave

Mode Data Link

-

SPEAKERS

+

˄ BRIDGED SWITCH ;SLAVE POSITION ˅

Master Slave

V I B E O W N E R ’ S M A N U A L

S

Y S T E M

W

I R I N G

VIBE3200D

BRIDGING TWO AMPLIFIERS

Master Slave ˄ BRIDGED SWITCH ; MASTER POSITION ˅

Master Amp

Slave Amp

PWR

L

Line

Out

R

Line

Input

L

Input

Level

Subsonic

Filter

LowPass

Filter

Bass

Boost

Min Max 10Hz 40Hz 50Hz 150Hz 0 18dB

PHASE

180°

Remote

R

Master Slave

Input sensitivity Bridged mode Data Link

PROT

From OUTPUTS of

HEAD UNIT

PWR

L

Line

Out

R

Line

Input

Input

Level

L

Min Max

Subsonic

Filter

LowPass

Filter

Bass

Boost

10Hz 40Hz 50Hz 150Hz 0

18dB

PHASE

180°

Remote

R

Master Slave

Input sensitivity Bridged mode

Data Link

PROT

SPEAKER IMPEDANCE

2 ohms!

+

-

+ -

SPEAKERS

+ -

SPEAKERS

REM + 12V GND

POWER

REM + 12V GND

POWER

˄ BRIDGED SWITCH ; SLAVE POSITION ˅

Master Slave

Bridging two amplifiers can be done only between two amplifiers of the same model number.

V I B E O W N E R ’ S M A N U A L — 1 1

T R O U B L E S H O O T I N G

Before removing your amplifier, refer to the list below and follow the suggested procedures. Always test the speakers and their wires first.

A M P L I F I E R W I L L N O T P O W E R U P .

Check for good ground connection.

Check that remote DC terminal has at least 13.8v DC.

Check that there is battery power on the +terminal.

Check all fuses.

Check that Protection LED is not lit. If it is lit, shut off amplifier briefly and then repower it.

H I G H H I S S O R E N G I N E N O I S E ( A L T E R N A T O R W H I N E ) I N S P E A K E R S .

Disconnect all RCA inputs to the amplifier(s)-if hiss / noise disappears, then plug in the component driving the amplifier and unplug its inputs. If hiss / noise disappears, go on until the faulty /noisy component is found.

It is best to set the amplifier’s input level as insensitive as possible. The best subjective S/N ratio is obtainable this way. Try to drive as high a signal level from the head unit as possible.

V

I B E

O

W N E R ’ S

M

A N U A L

P R O T E C T I O N L E D C O M E S O N W H E N T H E A M P L I F I E R I S P O W E R E D U P

Check for shorts on speaker leads.

Check that the volume control on the head unit is turned down low.

Remove speaker leads and reset the amplifier. If the Protection LED still comes on then the amplifier is faulty.

A M P L I F I E R ( S ) G E T S V E R Y H O T .

D I S T O R T E D S O U N D

H I G H S Q U E A L N O I S E F R O M S P E A K E R S .

V I B E O W N E R ’ S M A N U A L — 1 3

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement