Raymarine Maxiview ST80 Owner's Handbook Manual
Raymarine Maxiview ST80 is an advanced multifunction instrument that combines the functionality of multiple traditional instruments into one compact and easy-to-use display. It offers a wide range of features and capabilities to help you get the most out of your time on the water.
With Raymarine Maxiview ST80, you can easily monitor a variety of essential sailing data, including wind speed and direction, depth, speed, and more. The large, easy-to-read LCD display provides a clear and concise overview of all critical information, allowing you to make informed decisions while sailing. Additionally, the intuitive user interface makes it simple to access and adjust settings, even while underway.
Advertisement
Advertisement
ST80 Analogue Wind owner s handbook Document number: 81031_2 Date: 18th August 1998 ST80 Analogue Wind Operation and Setup Package Contents Analogue Wind display head Thumb nuts (2) Threaded fixing studs (2) White sun cover SeaTalk cable Installation template Operation manual Warranty card № 0 ANUN SS N N Operation cue card 10. Display head installation guide 2 ST80 Analogue Wind Operation and Setup Contents Chapter 1: Introduction ..........=-—.===--..=--...=--neeeneeneanaeaananea nano nene. 3 Chapter 2: OP@rAtION ..…...….………..0u0csaransenmensennen en nan san nanee annee maman em a names 4 2.1 Operation ..……….…..........….….…...…rerrrrrceccecenrereeccecenenerrccececcn00e 4 0210) 4 VIME ........eeoooccoocccarereocecanrececocanvecocecaaaccoccceaeon cera. 5 BÍt/max .............ee...ececccccerrecenececeneea ee ocercee re eeereceeeeeee 5 Man-Over-Board (MOB) ……................rrercrrerrernercee 5 HMllumination ..............e......ececccrrecocccececeoccee eee. 6 Operation by Remote Control .....................eeecereeecaccnens 7 Audible Alarms .................eeercercccocccccccccacerrereconococecace.. 7 Chapter 4: Setup .............==—...e==eaneeaeanneneaneneeanenennnnenennenennemenmnmeme 8 4.1 SEtup................eeececccrocncarreccacaaecooneneaneo ocean eee. 8 Wind Angle Response (A), Wind Speed Response (S) and VMG Response (V) ..................eeecarrrccccceccooccccanenooe 9 Units (UNIT) coerce eee eee, 9 Wind Angle (Mast) OffSet.....................eeecrreccsocccccanenes 9 Key Beep (BEEP) ................eeccccccccccocarcrcocacaceoceneeccce. 9 Illumination (L) .................e.ececenccccrrccceceorecrecacenecoaenence. 9 Contrast (C) L......errerrrrrcrneenserenserensennrrrncenecreseenecce 9 Alarm Control (ALRM) .…................rrerrernercreneercene 10 Quitting SetUPp .….…...…...….......….….……ccccccererercccceccrersecceuce 10 Chapter 4: CodeLock Security ........... e... =eene=0nnneanencannnaannenennes 11 4.1 Whatis CodeLock? ..................eeeccervecocececererecoccecnenene 11 4.2 Analogue Display Heads ......................eeeenerecrcoccccnenn— 12 4.3 Enabling CodeLock ..................eeeccarcecccocccereceneoccecenene 12 Chapter 5: Problem Solving .........--.=-==—--=======.nxxeenaneneenaneeee. 13 Chapter 6: EMC and Servicing Guidelines ...............-=—.. ee... 14 Chapter 7: Specification ............. =--.. ==... .-.xeeaaneneananeananeaneneanenme 16 ST80 Analogue Wind Operation and Setup 3 Chapter 1: Introduction The Analogue Wind presents both wind angle and wind speed information on a combined analogue and LCD display. * Wind speed is displayed on the dot-matrix LCD. e Wind angle is displayed by the 360° analogue dial. Additional features available at the touch of a button include: apparent wind, maximum and average wind speed, and maximum and average wind angle. Wind speed and angle information 1s provided by the ST80 “active” wind transducer. This truly active transducer is connected to SeaTalk via any ST80 display head or 3-way connector block. For night-time operation, the keypad, analogue dial and the LCD can be illuminated for superb readability and ease of operation. D1563-1 4 ST80 Analogue Wind Operation and Setup Chapter 2: Operation 2.1 Operation The following flowchart shows the functions assigned to the true/ app, vmg, and Bft/max keys. Note: All key presses in this chart are momentary. { TRUE | BEAUFORT | WIND | MG | SCALE {APPARENT | WIND | AVERAGE D1573-1 true/app e This key toggles true and apparent wind speed and wind angle. The LCD identifies the current mode by displaying “app” or “tru” in the top left hand corner. Note: True wind is “sailing true wind” relative to the water. ST80 Analogue Wind Operation and Setup 5 vmgy * Press vmg momentarily to display your velocity made good. * The analogue dial continues to show the wind direction (true or apparent as previously selected). * The current mode 1s identified by the “vmg” legend. * Tf boat speed not available, the needle will point to zero and the LCD displays a series of dashes. Bft/max * Press Bft/max momentarily to display the ground wind speed according to the Beaufort Scale (e.g., BF2). e The Beaufort scale, maximum and average wind speed displays are toggled using the Bft/max key. * The Beaufort scale, maximum and average wind speed displays can be reset to the current value by pressing Bft/Max for 3 seconds. The display flashes during the reset procedure. * The current scale 1s displayed for 8 seconds prior to the LCD display returning to normal operation. Man-Over-Board (MOB) The LCD displays “MOB” if the ST80 Wind instrument receives a man-over-board signal via SeaTalk. ® This display overrides the current display until the MOB signal is cancelled. ST80 Analogue Wind Operation and Setup lllumination Instrument Illumination sets the lighting for the Analogue Wind only. System illumination adjusts the lighting of all the display heads in system mode. 1 second llumination lumination | System | Local Press this key for 5 seconds to enter local from system Press for 1 second to return to system Press this key for 1 second to reset the contrast to the factory default | LEVEL 3 D1572-1 The illumination display returns to normal operation after 8 seconds of keypad inactivity. However, you can return to normal operation immediately by simply pressing the true/app, vmg, or Bft/max key. ST80 Analogue Wind Operation and Setup 7 Operation by Remote Control It is possible to operate the Analogue Wind from a remote location, using the ST80 Remote Keypad. This keypad mirrors the functions of the ST80 display head keypads. For operation and setting up details, please refer to the Remote Keypad Operation and Setup manual. Audible Alarms There are basically two types of audible alarm: high priority and low priority. High priority alarms beep continuously while low priority alarms consist of three beeps followed by a 5 second break. * High priority alarms will always override low priority alarms. * Once the high priority alarm has cleared, the previous alarm, if it is still current, will be reinstated. ST80 Analogue Wind Operation and Setup Note: Wind Angle Response (A), Wind Speed Response (S) and VMG Response (V) Response controls the rate at which wind speed, wind angle and VMG information is updated. The range is between 1 and 15; a low number provides a smooth response and a high number a much livelier response with rapid pointer movement. The displayed value is adjusted using the true/app or vmg keys. Units (UNIT) This option 1s used to select the wind speed units: mph, m/s, or kts. Use the true/app or vmg keys to toggle the units. Any unit changes will be reflected by other SeaTalk instruments. Wind Angle (Mast) Offset Wind angle offset 1s used to align the Active Wind Transducer to the wind direction. This is achieved by sailing directly into the wind and adjusting the pointer to “0” using the true/app or vmg keys. This is not available 1f a wind transducer 1s not connected. Key Beep (BEEP) The keypad, by default, beeps when a key is pressed. However, this can be turned ON and OFF as required using the true/app or vmg keys. lllumination (L) This feature 1s used to adjust the brightness of the dial for each illumination setting. Use the true/app (decrease) or vmg (increase) keys. Contrast (C) Adjusts the display contrast. The range is from 0 to 15 and is adjusted using the true/app (decrease) or vmg (increase) keys. ST80 Analogue Wind Operation and Setup 11 Chapter 4: CodeLock Security 4.1 What is CodeLock? CodeLock 1s a personal four digit security code designed to protect your valuable equipment against theft. CodeLock does not have to be switched on, but it’s there if you decide that you need it. When CodeLock 1s switched on, the code number 1s stored in the memory of all CodeLock compatible equipment on the same bus. A CodeLocked piece of equipment, if stolen, cannot be used without the correct code number. There are basically two types of CodeLock compatible equipment: master’s and slave’s. Masters Are used to create and enter a CodeLock code number. The ST80 Masterview is a master display head. Slave's Cannot be used to create a CodeLock code number. Can be used to enter a code number to unlock a system. Receive and transmit your chosen code number only. ST80 slave’s consist of the: Analogue Wind, Analogue Close Hauled Wind, Analogue Compass, Analogue Multitrim, Maxiview and Multiview. Code creation is usually a once-off procedure carried out on a master display head, which, ideally, is situated in a secure location below deck. Once entered, the code 1s automatically sent to all CodeLock compatible SeaTalk equipment without further intervention. H you require a higher degree of security, perhaps all your instruments are mounted in exposed locations, CodeLock can demand that you enter your personal code every time the system is switched on. In this configuration, the code can be entered into any convenient master display head. ST80 Analogue Wind Operation and Setup 13 Chapter 5: Problem Solving 5.1 Problem Solving Display is blank - keypad not illuminated * Make sure that the power supply is connected. * Check the fuse or circuit breaker. * Make sure that the SeaTalk cables are not damaged. Display is blank - keypad illuminated * Check the contrast and illumination settings e Faulty LCD module. No exchange of information between SeaTalk instruments * Make sure that the cables are attached securely. [If the problem persists, disconnect your instruments one by one to isolate the faulty unit. Failure of a group of SeaTalk instruments * Make sure that the SeaTalk connections to non-functioning instruments are secure. LCD shows “Code ON” when the power supply is switched on * The CodeLock anti-theft system 1s operational. Poor character definition * Adjust the contrast. ST80 Analogue Wind Operation and Setup 15 6.3 Check Before Going to Sea * Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc.. * In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not damage the equipment but can lead to it resetting, or momentarily may result in faulty operation. 6.4 Servicing and Safety * Autohelm equipment should be serviced only by authorised Autohelm service engineers. They will ensure that service procedures and replacement parts used will not affect performance. There are no user serviceable parts in any Autohelm product. * Some products generate high voltages, and so never handle the cables/connectors when power is being supplied to the equipment. e Always report any EMC related problem to your nearest Autohelm dealer. We will use any such information to improve our quality standards. ">

Public link updated
The public link to your chat has been updated.
Advertisement