Suzuki FD 110 XC, FD 110 XCD, FD 110 XCS, FD 110 XCSD Service Manual
The Suzuki FD 110 XCSD is an air-cooled, single-cylinder motorcycle designed for versatility and affordability. It features a 4-speed transmission, a sturdy single rectangular frame (SSRF), and both an electric starter and a kick starter. This motorcycle is ideal for commuting, leisure riding, and navigating various terrains.
Advertisement
Advertisement
FD110
FOREWORD
This manual contains an introductory description On
SUZUKI FD 110 and procedures for Its inspection/service and overhaul of its main components.
Other information considered as generally known is not included. Read GENERAL INFORMATION section to Familiarize yourself with outline of the vehicle and MAINTENANCE and other sections to use as a guide for proper inspection and service. This manual will help you now the vehicle better so that you can assure your customers of your optimum and quick service.
* This manual has been prepared on the basis of the latest specifications at the time of publication.
If modifications have been made since then, differences may exist between the content of this manual and the actual motorcycle.
* IIIustrations in this manual are used to show the basic principles of operation and work procedures. They may not represent the actual motorcycle exactly in detail.
* This manual is written for persons who have enough knowledge, skills and tools, including special tools, for servicing SUZUKI motorcycles. If you do not have the proper knowledge and tools, ask your authorized SUZUKI motorcycle dealer to help you.
Inexperienced mechanics or mechanics
Without the proper tools and equipment may not be able to properly perform the service described I this manual. Improper repair may result I injury to the mechanic and may render the motorcycle unsafe for the rider and passenger.
© COPYRIGHT SUZUKI MOTOR CORPORATION 2012
GROUP INDEX
GENERAL INFORMATION
PERIODICAL MAINTENANCE
ENGINE
FUEL AND LUBRICATION SYSTEM
CHASSIS
ELECTRICAL SYSTEM
SERVICING INFORMATION
COOLING AND LUBRICATION SYSTEM
CHASSIS
ELECTRICAL SYSTEM
SERVICING INFORMATION
EMISSION CONTROL INFORMATION
VZR1800K7 (’07-MODEL)
VZR1800ZK7 (’07-MODEL)
VZR1800NK8 (’08-MODEL)
VZR1800K8 (’08-MODEL)
VZR1800ZK8/ZK9 (’08, ’09-MODEL)
VZR1800K9/NK9 (’09-MODEL)
VZR1800/ZL0/ZL1 (’10, ’11-MODEL)
VZR1800/ZL2 (’12-MODEL)
WIRING DIAGRAM
3
4
5
1
2
8
9
6
7
10
11
16
17
18
19
20
21
12
13
14
15
HOW TO USE THIS MANUAL
TO LOCATE WHAT YOU ARE LOOKING FOR :
1. The text of this manual is divided into sections.
2. As the title of these sections are listed on the previous page as GROUP INDEX, select the section where what you are looking for belong.
3. Holding the manual as shown as the right will allow
4. On the first page of each section, its contents are listed. Find the item and page you need.
COMPONENT PARTS AND WORK TO BE DONE
Under the name of each system or unit, its exploded view provided with work instruction and other service information such as the tightening torque, lubricating and locking agent points.
Example:
LEFT RIGHT
22.0-35.0 N-m
SYMBOL
Listed in the table below are the symbols indicating instructions and other information necessary for servicing and meaning associated with them respectively.
SYMBOL DEFINITION
Torque control required.
Data beside it indicates
Specified torque.
Apply oil, Use engine oil unless otherwise specified.
SYMBOL DEFINITION
Apply THREAD LOCK SUPER “1303”
99000-32030
Apply THREAD LOCK “1342”
99000-32050
Apply SUZUKI SUPER GREASE “A”
99000-25010
Apply SUZUKI SILICONE GREASE.
99000-25100
Apply SUZUKI MOLY PASTE.
99000-25140
Apply SUZUKI BOND “1215”
99000-31110
Apply THREAD LOCK SUPER “1322”
99000-31110
Apply THREAD LOCK SUPER “1360”
99000-32130
Apply or use brake fluid.
Measure in voltage range.
Measure in resistance range.
Measure in current range.
Use special tool.
Use fork oil.
99000-99044-10G
GENERAL INFORMATION 1-1
GENERAL INFORMATION
1
CONTENTS
WARNING/CAUTION/NOTE........................................................................... 1-2
GENERAL PRECAUTIONS ............................................................................ 1-2
SUZUKI FD 110 XC / XCS / XCD / XCSD....................................................... 1-4
SERIAL NUMBER LOCATION ....................................................................... 1-4
FUEL AND OIL RECOMMENDATIONS .................................................. 1-4
FUEL ..................................................................................................... 1-4
ENGINE OIL.......................................................................................... 1-5
FRONT FORK OIL ................................................................................ 1-5
BREAK-IN PROCEDURES............................................................................. 1-5
SPECIFICATIONS........................................................................................... 1-6
1-2 GENERAL INFORMATION
WARNING/CAUTION/NOTE
Please read this manual and follow its instructions carefully. To emphasize special information, the symbol and the words WARNING, CAUTION and NOTE have special meanings. Pay special attention to the messages highlighted by these signal words.
Indicates a potential hazard that could result in death or injury.
Indicates a potential hazard that could result in vehicle damage.
NOTE:
Indicates special information to make maintenance easier or instructions clearer.
Please note, however, that the warnings and cautions contained in this manual cannot possibly cover all potential hazards relating to the servicing, or lack of servicing, of the motorcycle. In addition to the WARN-
INGS and CAUTIONS stated, you must use good judgement and basic mechanical safety principles. If you are unsure about how to perform a particular service operation, ask a more experienced mechanic for advice.
GENERAL PRECAUTIONS
* Proper service and repair procedures are important for the safety of the service mechanic and the safety and reliability of the vehicle.
* When 2 or more persons work together, pay attention to the safety of each other.
* When it is necessary to run the engine indoors, make sure that exhaust gas is forced outdoors.
* When working with toxic or the flammable materials, make sure that the area you work in is well ventilated and that you follow all of the material manufacturer’s instructions.
* Never use getting burned, do not touch the engine, engine oil or exhaust system during or for a while after engine operation.
* After servicing fuel, oil, exhaust or brake systems, check all lines and fittings related to the system for leaks.
GENERAL INFORMATION 1-3
* If parts replacement is necessary, replace the parts with Suzuki Genuine Parts or their equivalent.
* When removing arts that are to be reused, keep them arranged in an orderly manner so that they may be reinstalled in the proper order and orientation.
* Be sure to use special tools when instructed.
* Make sure that all parts used in reassembly are clean, and also lubricated when specified.
* When use of a certain type of lubricant, bond, or sealant is specified be sure to sue the specified type.
* When removing the battery, disconnect the negative cable first and then positive cable. When reconnecting the battery, connect the positive cablefirst and then negative cable, and replace the terminal cover on the positive terminal.
* When performing service to electrical arts, if the service procedures not require use of battery power, disconnect the negative cable of the battery.
* Tighten cylinder head case bolts and nuts, beginning with larger diameter and ending with smaller diameter, from inside to outside diagonally, to the specified tightening torque.
* Whenever you remove oil seals, gaskets, packing, O-rings, locking washers, cotter pins, circlips and certain other parts as specified, be sure to replace them with new ones. Also, before installing these new parts, be sure to remove any left over material from the mating surfaces.
* Never reuse a circlip. When installing a new circlip, take care not to expand the end gap larger than required to slip the circlip over the shaft. After installing a circlip, always ensure that it is completely seated in its groove and securely fitted.
* Do not use self-locking nuts a few times over.
* Use a torque wrench to tighten fasteners to the torque values when specified. Wipe off grease or oil if a thread is smeared with them.
* After reassembly, check parts for tightness and operation.
* To protect environment, do not unlawfully dispose of used motor oil and other fluids: batteries, and tires.
* To protect Earth’s natural resources, properly dispose of used vehicles and parts.
1-4 GENERAL INFORMATION
SUZUKI FD 110 XB517QD/XB517QSC
• Difference between illustrations and actual motorcycles depends on the markets.
SERIAL NUMBER LOCATION
The frame serial number or V.I.N. (Vehicle Identification Number) is stamped on the left side of the steering head tube. The engine serial number is located on the upper right side of the crankcase. These numbers are required especially for registering the machine and ordering spare parts.
FUEL AND OIL RECOMMENDATIONS
FUEL
Gasoline used should be graded 91 (Research Method)_ or higher. An unleaded gasoline type is recommended.
GENERAL INFORMATION 1-5
ENGINE OIL
Be sure the engine oil you use comes under API classification of
SF or SG and that its viscosity rating is SAE 40. If an SAE 40 motor oil is not available, select an alternate according to the right chart
BRAKE FLUID
Specification and classification: DOT 4
Since the brake system of this motorcycle is filled with a glycol-based brake fluidby the manufacturer, do not use or mix different types of fluid such as silicone-based and petroleum-based fluid for refilling the system, otherwise serious damage will result.
Do not use any brake fluid taken from old or used or unsealed containers.
Never re-use brake fluid left over from a previous servicing, which has been stored for a long period.
FRONT FORK OIL
Use fork oil # 10.
BREAK-IN PROCEDURES
During manufacture only the best possible materials are used and all machined parts are finished to a very high standard but it is still necessary to allow the moving parts to “BREAK-IN” before subjecting the engine to maximum stresses. The future performance and reliability of the engine depends on the care and restraint exercised during its early life. The general rules are as follows.
• Keep to this break-in throttle position. Initial 500 km: less than ½ throttle Up to 1,600 km: Less than ¾ throttle
• Upon reaching an odometer reading of 1,600 km you can subject the motorcycle to full throttle operation for short periods of time.
1-6 GENERAL INFORMATION
SPECIFICATIONS
DIMENSIONS AND DRY MASS
Overall length.............................................................. 1,932 mm
Overall width .............................................................. 650 mm
Overall height ............................................................. 1,062 mm
Seat height ................................................................. 755 mm
Wheel base ................................................................ 1,230 mm
Ground clearance ...................................................... 153 mm
Dry mass .................................................................... 96 kg
ENGINE
Type ........................................................................... Four-stroke, air-cooled, SOHC
Number of cylinder ..................................................... 1
Bore ........................................................................... 53.5 mm
Stroke ......................................................................... 48.8 mm
Piston Displacement .................................................. 109.6 cm
3
Compression ration .................................................... 9.6 : 1
Carburetor .................................................................. MIKUNI VM17
Air cleaner .................................................................. Paper
Starter system Electric starter & Kick starter starter Lubrication system Wet sump
Valve clearance ......................................................... IN : 0.04-0.07 mm.
EX : 0.04-0.07 mm.
TRANSMISSION
Clutch ......................................................................... Wet shoe, automatic, centrifugal type
Transmission .............................................................. 4-speed constant mesh
Gearshift pattern ........................................................ All-down
Primary reduction ratio ............................................... 3.666 (77/21)
Final reduction ratio ................................................... 2.428 (34/14)
Gear ratios, Low ......................................................... 3.000 (33/11)
2nd ......................................................... 1.875 (30/16)
3rd .......................................................... 1.368 (26/19)
Top ......................................................... 1.052 (20/19)
Drive chain ................................................................. DIADO D.I.D 428, 98 links
GENERAL INFORMATION 1-7
CHASSIS
Frame ......................................................................... SSRF (SUZUKI SINGLE RECTANGULAR FRAME)
Front suspension ........................................................ Telescopic, coil spring, oil damped
Rear suspension ........................................................ Swing arm type, coil spring
Steering angle ............................................................ 45° (right & left)
Caster ......................................................................... 27°
Trail ............................................................................ 65 mm
Front brake ................................................................. Disc brake, hydraulically operated
Expanding, drum, brake.
Rear brake ................................................................. Internal expanding, drum brake
Front tire size ............................................................. 2.25 – 17 NR72 33L
Rear tire size .............................................................. 2.50 – 17 NR72 38L
Front fork stroke ......................................................... 90 mm
Rear wheel travel ....................................................... 79 mm
ELECTRICAL
Ignition type................................................................. DC-CDI
Spark plug .................................................................. ND: U20FS-U
NGK: C6HS
Batter .......................................................................... 12 V 5AH 10HR
Fuse ............................................................................ 10 A
Headlight ..................................................................... 12 V 35/35 W
Turn signal light........................................................... 12 V 10 W
Taillight/Brake light ..................................................... 12 V5/21W
Speedometer light ...................................................... 12 V 3 W
High beam indicator light ............................................ 12 V 1.7 W
Turn signal indicator light ........................................... 12 V 1.7 W
Neutral, gear position indicator light ........................... 12 V 1.7 W
CAPACITY
Fuel tank .................................................................... 4.2 L
Engine oil, oil change ................................................. 800 ml with filter change ........................................................ 900 ml overhaul ..................................................................... 1,000 ml
Front fork oil ............................................................... 70 ml
These specifications are subject to change without notice.
1-8 GENERAL INFORMATION
PERIODICAL MAINTENANCE 2-1
PERIODICAL MAINTENANCE
CONTENTS
PERIODICAL MAINTENANCE SCHEDULE ................................................. 2-2
PERIODIC MAINTENANCE CHART....................................................... 2-2
LUBRICATION POINTS .......................................................................... 2-3
MAINTENANCE AND TUNE-UP PROCEDURES ......................................... 2-4
BATTERY ................................................................................................ 2-4
EXHAUST PIPE BOLTS.......................................................................... 2-5
AIR CLEANER ........................................................................................ 2-5
VALVE CLEARANCE.............................................................................. 2-6
SPARK PLUG.......................................................................................... 2-8
ENGINE OIL ............................................................................................ 2-9
OIL FILTER.............................................................................................. 2-9
FUEL HOSE........................................................................................... 2-10
FUEL FILTER ........................................................................................ 2-10
CARBURETOR...................................................................................... 2-10
DRIVE CHAIN........................................................................................ 2-11
BRAKE .................................................................................................. 2-13
TIRE ....................................................................................................... 2-16
STEERING............................................................................................. 2-16
FRONT FORK........................................................................................ 2-17
REAR SUSPENSION ............................................................................ 2-17
CHASSIS BOLTS AND NUTS .............................................................. 2-18
COMPRESSION PRESSURE CHECK ........................................................ 2-20
OIL PRESSURE CHECK ............................................................................. 2-21
AUTOMATIC CLUTCH INSPECTION ......................................................... 2-22
2
2-2 PERIODIC MAINTENANCE
PERIODICAL MAINTENANCE SCHEDULE
The chart below lists the recommended intervals for all the required periodic service work necessary t keep the motorcycle operating at peak performance and economy. Mileages are expressed in terms of kilometers and time for your convenience.
NOTE:
More frequent servicing may be performed on motorcycles that are used under severe conditions.
PERIODIC MAINTENANCE CHART
Item
Battery
Exhaust pipe bolts
Air cleaner
Valve clearance
Spark
Engine oil
Engine oil filter
Fuel hose
Clutch
Fuel filter
Interval Km
Engine idle rpm (Carburetor)
Months
Throttle cable play (Carburetor)
Drive chain
Brakes
Tires
Steering
Cylinder head nut
Suspension
Chassis bolts and nuts
1,000 4,000 8,000 12,000 16,000 20,000 24,000
1
I
I
I
T
—
R
R
T
—
T
I
I
I
I
I
I
I
I
I
6
I
I
I
T
C
R
—
I
I
I
I
I
I
I
I
I
T
—
T
12 18 24
I
I
I
I
I
I
T
I
T
I
I
R
T
C
I
I
I
T
R
R R R
Replace every 4,000 km
R — R
Replace every 8,000 km
I I I
I
I
I
I
I
I
I
I
R
T
C
I
I
I
I
I
I
T
—
T
I
I
I
I
I
I
T
I
T
30
I
I
I
T
C
R
I
I
I
I
I
I
I
I
I
I
T
—
T
36
I
I
R
T
R
R
R
T
I
T
I
I
I
I
I
I
I
I
I
NOTE:
I: Inspection and adjust, clean, Lubricate or replace as necessary
C: Clean R: Replace T: Tighten
PERIODIC MAINTENANCE 2-3
LUBRICATION POINTS
Proper lubrication is important for smooth operation and long life of each working part of the motorcycle.
Major lubrication points are indicated below.
DRIVE CHAIN
SPEEDOMETER
GEARBOX
FRONT WHEEL
BEARING
AXLE SHAFT
FRONT BRAKE CAM
REAR BRAKE CAM
REAR WHEEL
BEARING
AXLE SHAFT
SPEEDOMETER
CABLE
SIDE STAND PIVOT
AND SPRING HOOK
BRAKE PEDAL
PIVOT
CENTER STAND PIVOT
AND SPRING HOOK
THROTTLE CABLE
STEERING STEM
BEARING
KICK STARTER LEVER
PIVOT
BRAKE LEVER
HOLDER
NOTE:
* Before lubricating each part, clean off any rusty spots and wipe off any grease, oil, dirt or grime.
* Lubricate exposed parts which are subject to rust, with a rust preventative spry whenever the motorcycle has been operated under wet or rainy condition.
2-4 PERIODIC MAINTENANCE
MAINTENANCE AND TUNE-UP PROCEDURES
This section describes the servicing procedures for each item of the Periodic Maintenance requirements.
BATTERY
Inspect initially at 1,000 km (1 month) and Every
4,000 km (4 months) thereafter.
• The battery must be removed to check the electrolyte level and specific gravity.
• Open the seat.
• Remove battery and + leads at the battery terminals.
When removing the battery, disconnect the negative cable first and then the positive cable.
• Remove battery from the frame.
• Check electrolyte for level and specific gravity. Add distilled water, as necessary, to keep the surface of the electrolyte above the LOWER. Level line but not above the UPPER.
Level line.
For checking specific gravity, use a hydrometer to determine the charged condition.
09900-28403: Hydrometer
Battery type ….GM3-3B
Standard specific gravity 1.26 at 20 °C
Battery type …. YB5L-B
Standard specific gravity 1.28 at 20 °C
An S.G. reading of 1.22 [YB5L-B] 1.20 [GM 3-3B] (AT 20oC) or under means that the battery needs recharging off the machine:
Take if off and charge it from a recharge. Charging the battery in place can lead to failure of the regulator or rectifier.
• To install the battery, reverse the procedure cribbed above.
Hydrometer
PERIODIC MAINTENANCE 2-5
When installing the battery lead wires fix the + Led first and lead last.
• Make sure that the breather pipe is tightly secured and undamaged, and is routed as shown in the photograph.
BATTERY
BATTERY BREATHER HOSE
EXHAUST PIPE BOLTS
Tighten Initially at 1,000 km (1 month) and Inspect
Every 4,000 km (6 months) thereafter.
• Tighten the exhaust pipe clamp bolts and muffler mounting bolts to the specified torque with a torque wrench.
Exhaust pipe nut: 1.1 kg-m
Muffler mounting bolt: 2.6 kg-m
AIR CLEANER
Clean Every 4,000 km (6 months).
If the air cleaner is clogged with dust, intake resistance will be increased with a resultant decrease in output and an increase the fuel consumption. Check and clean the element in the following manner.
• Loosen the 3 screw.
• Take off the air cleaner cover.
• Remove the element from the case.
2-6 PERIODIC MAINTENANCE
• Loosen the four screw and remove the air cleaner cover.
• Remove the air cleaner element.
• Carefully use an air hose to blow the dust form the cleaner element inside.
• Reinstall the cleaned or new cleaner element in the reverse order of removal.
Always use air pressure on the side of the steel sheet.
If driving under dusty condition, clean the air cleaner element more frequently. The surest way to accelerate engine wear is to use the engine without the element or to use a ruptured element. Make sure that the air cleaner is in good condition at all times. Life of the engine depends largely on this component !
VALVE CLEARANCE
Inspect Initially at 1,000 km (1 month) and Every
4,000 km (6 months) thereafter.
Excessive valve clearance results in valve noise and insufficient valve clearance results in valve damage and reduced power. At the distances indicated above, check and adjust the clearance to the following specification.
Clean Every 4,000 km (6 months).
Valve clearance (When cold):
IN.: 0.04 - 0.07 mm
EX.: 0.04 - 0.07 mm
• Remove the center leg shield.
• Remove the leg shields, left and right.
• Remove the carburetor by loosening the screws
The procedure for adjusting the valve clearance is as follows:
NOTE:
* The piston must be at (TDC) on the compression stroke in order to check the valve clearance or to adjust valve clearance.
* The clearance specification is for GOLD state.
• Remove spark plug, valve inspection caps 1 and valve timing inspection plug 2 .
PERIODIC MAINTENANCE 2-7
1
• Remove the magneto cover cap and rotate the magneto rotor with box wrench to set the piston at (TDC) of the compression stroke. (Rotate the rotor until the “T” line on the rotor is aligned with the center of hole on the magneto cover.
2
• Insert the thickness gauge to the clearance between the valve stem end and the adjusting screw on the rocker arm.
09900-20803: Thickness gauge
• If clearance is off the specification, bring it into the specified range by using the special tool.
• Reinstall spark plug, valve inspection caps, valve timing inspection plug and magneto cover cap.
09917-14910: Tappet adjust driver
Rockerarm
Adjuster Screw
Valve clearance
NOTE:
* The clearance specification is for GOLD state
2-8 PERIODIC MAINTENANCE
SPARK PLUG
Inspect at 4,000 km (6 month) Replace Every
8,000 km (12 months).
• Carbon deposits on the spark plug will prevent good sparking and cause misfiring. Clean the deposits off periodically
• If the center electrode is fairly worn down, the plug should be replaced and the plug gap set to the specified gap using a thickness gauge.
09900-20803: Thickness gauge
Spark plug gap 0.6 - 0.7 mm
• Check spark plug for burnt condition. If abnormal, replace the plug as indicated below.
NGK NIPPON DENSO REMARKS
CR6HSA 0.6 - 0.7 mm 0.6 - 0.7 mm
• Tighten the spark plug in the cylinder head with the specified torque by using special tool.
Spark plug: 1.1 kg-m
9930-10121: Spark plug socket wrench set
Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result. mm.
0.6-0.7 mm.
PERIODIC MAINTENANCE 2-9
ENGINE OIL
Replace Initially at 1,000 km (1 month) and Every
4,000 km thereafter.
After a long period of use, the engine oil will deteriorate and quicken the wear of sliding and interlocking surfaces. Replace the transmission oil periodically following the procedure below.
• Start the engine to warm up the oil, this will facilitate draining of oil, Turn off the engine.
• Unscrew the oil filler cap 1 and drain plug 2 and drain the oil completely.
• Tighten the drain plug.
• Supply the good quality SAE 40 motor oil.
• Start up the engine and allow it to run for several minutes at idling speed.
• Turn off the engine and wait about one minute.
• Check the oil level with the dipstick.
The level found in the dipstick should be between “L” (Low) and
“F” (Full) lines
Oil viscosity and classification: SAE 40, API: SF, SG
Oil drain plug: 1.8 kg-m
NOTE:
To check the oil level, holding the motorcycle vertically, reinsert the dipstick until the threads touch filler neck, but do not screw the cap in.
OIL FILTER
The engine oil should be changed while the engine is hot. Oil filter replacement at the above intervals should be done together with engine oil change.
• Keep the motorcycle upright with Center stand.
• Place an oil pan under the engine.
• Remove the oil filter cap 1 by removing the bolts.
• Remove the oil filter 2 and install the new one.
• Replace the filter and tighten the bolts securely
NOTE:
Before installing the new oil filter and filter cap, check to be sure that the spring 3 and new o-rings 4 , 5 are installed correctly.
1
1
!
LOWER UPPER
4
2
3
5
2-10 PERIODIC MAINTENANCE
NECESSARY AMOUNT OF ENGINE OIL
OIL CHANGE: 800 ml
OIL FILTER CHANGE:
OVER HAUL:
900 ml
1,000 ml
FUEL HOSE
Inspect at 4,000 km (6 month) Replace Every 4 years
FUEL FILTER
Clean Every 8,000 km (12 months).
CARBURETOR
Inspect Initially at 1,000 km (1 month) and Every
4,000 km (6 months) thereafter.
IDLE RPM (Idling adjustment)
• Adjust the throttle cable play.
• Warm up the engine
NOTE:
Make this adjustment when the engine is hot.
• Connect an electric tachometer.
• Start up the engine and set its speed at any where between
1,500 and 1,600 r/min by turning adjust screws.
Engine idle speed: 1,500 ± 100 r/min
09900-26006: Tachometer
THROTTLE CABLE PLAY
Throttle cable play A should be 2-4 mm as measured at throttle grip when turning the throttle grip lightly. If the play A in the throttle cable is incorrect, adjust it in the following way:
• Loosen the lock nut 1 and turn the adjuster 2 in or out until the specified play is obtained.
• Tighten the lock nut 1 while holding the adjuster 2 .
Throttle cable play A: 2- 4 mm.
A
2 1
PERIODIC MAINTENANCE 2-11
After the adjustment is completed, check that handlebar movernent does not raise the engine idle speed and that the throttle grip returns smoothly and automatically.
DRIVE CHAIN
Inspect Initially at 1,000 km (1 month) and Every
4,000 km (6 months) thereafter. Clean and lubricate
Every 1,000 km
Visually inspect the drive chain for the below listed possible malconditions.
• Loose pins
• Damaged rollers
• Rusted links
• Twisted or seized links
Excessive wear
If any defects are found, the drive chain must be replaced.
2
1
Checking
• Remove the chain case by loosening four screws 1 and bolt 2 .
The standard drive chain is DAIDO DID 428. SUZUKI recommends that this standard drive chain should be used for the replacement.
• Count out 21 pins (20-pitch) on the chain measure the distance between the two. If the distance exceed following limit, the chain must be replaced.
Drive chain 20-pitch length: 259 mm
1 2 3 19 20 21
2-12 PERIODIC MAINTENANCE
NOTE:
When replacing the drive chain, replace the drive chain and sprockets as a set.
CLEANING AND LUBRICATING
Wash the drive chain in cleaning solvent and lubricate it with chain lube or motor oil. If the motorcycle operates under dusty conditions, frequent rapid acceleration or at sustained high speeds, the drive chain should be cleaned and lubricated more often.
ADJUSTING
• Loosen the nut 1 .
• Loosen or tighten the adjusters 2 until the chain has 15-25 mm of slag at the middle between engine and rear sprockets, the mark 3 on the swing arm must be at the same position the scale mark on both chain adjuster 4 to ensure that the front and rear wheels are correctly aligned.
• Tighten the axle nut 1 after adjusting the drive chain and tighten the adjuster nuts 2 .
Rear axle nut: 4.5 kg-m
3
4 1
2
1
15-25 MM
BRAKE
(BRAKE)
Inspect Initially at 1,000 km (1 month) and Every
4,000 km (6 months) thereafter.
(BRAKE HOSE AND BRAKE FLUID)
Inspect Every 4,000 km (6 month) Replace houses
Every 4 years. Replace Fluid Every 2 years.
FRONT BRAKE (DISC TYPE)
• Keep the motorcycle upright and place the handlebars straight.
• Check the brake fluid level by observing the lower limit line on the front brake fluid reservoir.
• When the level is below the lower limit line, remove the front handlebar’s cover and replenish with brake fluid that meets the following specification.
Specification and Classification: DOT 4
The brake system of this motorcycle is filled with a glycol-based brake fluid. Do not use or mix different types of fluid such as silicone-based or petroleumbased. Do not use any brake fluid taken from oil, used or unsealed containers. Never re-use brake fluid left over from the last servicing or stored for a long period.
Brake fluid, if it leaks, will interfere with safe running and immediately discolor painted surfaces. Check the brake hoses and hose joints for cracks and oil leakage before riding.
BRAKE PADS (DISC TYPE)
The extent to brake pad wear can be checked by observing the grooved limit line 1 on the pad. When the wear exceeds the grooved limit line, replace the pads with new ones. (Refer to page 5-12.)
Replace the brake pad as a set, otherwise braking performance will be adversely affected.
PERIODIC MAINTENANCE 2-13
2-14 PERIODIC MAINTENANCE
AIR BLEEDING THE BRAKE FLUID CIRCUIT
(DISC BRAKE)
Air trapped in the fluid circuit acts like a cushion to absorb a large proportion of the pressure developed by the master cylinder and thus interferes with the full braking performance of the brake caliper. The presence of air is indicated by “sponginess” of the brake lever and also by lack of braking force.
Considering the danger to which such trapped air exposes the machine and rider, it is essential that, after remounting the brake and restoring the brake system to the normal condition, the brake fluid circuit be purged of air in the following manner.
• Fill up the master cylinder reservoir to the upper end of the inspection window. Replace the reservoir cap to prevent entry of dirt.
• Attach a pipe to the caliper bleeder valve, and insert the free end of the pipe into a receptacle.
• Front brake: Bleed air from the air bleeder valve.
• Squeeze and release the brake lever several times in rapid succession and squeeze the lever fully without releasing it.
Loosen the bleeder valve by turning it a quarter of a turn so that the bleeder valve by turning it a quarter of a turn so that the brake fluid runs into the receptacle; this will remove the tension of the brake lever causing it to touch the handlebar grip. Then, close the valve, pump and squeeze the lever, and open the valve.
• Repeat this process until the fluid flowing into the receptacle no longer contains air bubbles.
NOTE:
Replenish the brake fluid in the reservoir as necessary while bleeding the brake system. Make sure that there is always some fluid visible in the reservoir.
• Close the bleeder valve, and disconnect the pipe. Fill the reservoir with brake fluid to the “UPPER” end of the inspection window.
Air bleeder valve: 8.0 N-m (0.8 kg-m)
64
65
2
Handle brake fluid with care: the fluid reacts chemically with paint, plastics, rubber materials etc.
BRAKE LEVER PLAY ADJUSTING (DRUM TYPE)
Adjust by turning the adjusting nut 1 so that the play 2 is
15-25 mm as follows.
66
1
REAR BRAKE ADJUSTING
Adjust the free travel 1 to 15-25 mm. by turning the adjusting nut 2 .
PERIODIC MAINTENANCE 2-15
1
2
REAR BRAKE SHOE WEAR
This motorcycle is equipped with brake lining wear limit indicator. As shown in Fig., at the condition of normal lining wear, the extension line of the index mark on the brake camshaft should be within the range embossed on the brake panel with brake on.
To check wear of the brake lining, perform the following steps.
• First check if the brake system is properly adjusted.
• While operating the brake, check to see that the extension line of the index mark is within the range on the brake panel
• If the index mark is beyond the range as shown in the Fig., the brake shoe assembly should be replaced with a new set of shoes.
2-16 PERIODIC MAINTENANCE
TIRE
Inspect Every 4,000 km (6 months).
TIRE TREAD CONDITION
Operating the motorcycle with excessively worn tires will decrease riding stability and consequently invite a dangerous ours situation. It is highly recommended to replace a tire when the remaining depth of tire tread reaches the following specification.
Tire tread depth limit: 1.6 mm
09900-2080: Tire depth gauge
TIRE PRESSURE
If the tire pressure is too high or too low, steering will be adversely affected and tire wear increased. Therefore, maintain the correct tire pressure for good readability of shorter tire life will result. Cold inflation tire pressure is follows.
COLD INFLATION TIRE
PRESSURE
FRONT
REAR kPa
175
225 kg/cm 3
1.75
2.25
The standard tire fitted on this motorcycle is 2.50-17 for front and 2.75-17 for rear. The use of tires other than those specified may cause instability. It is highly recommended to use a SUZUKI Genuine Tire.
STEERING
Inspect Initially at 1,000 km (1 month) and Every
8,000 km (12 months) thereafter.
Ball type bearings are equipped on the steering system. Steering should be adjusted properly for smooth turning of handlebars and safe running. Over tight steering prevents smooth fuming of the handlebars and too loose steering will cause poor stability.
Check that there is no play in the front fork assembly by supporting the machine so that the front wheel is off the ground, with the wheel straight ahead, grasp the lower fork tubes near the axle and pull forward. If play is found, perform steering. bearing adjustment as described in page 5-25 of this manual.
FRONT FORK
Inspect Every 8,000 km (12 months).
Inspect the front forks oil leakage, scoring or scratches on the outer surface of the inner tubes. Replace any defective parts, if necessary. (Refer to page 5-19)
REAR SUSPENSION
Inspect Every 8,000 km (12 months).
Inspect the rear shock absorber for oil leakage and damage.
Replace any defective parts, if necessary.
PERIODIC MAINTENANCE 2-17
2-18 PERIODIC MAINTENANCE
CHASSIS BOLTS AND NUTS
The nuts and bolts listed below are important safety related parts. They must be retightened when necessary to the specified torque with a torque wrench. (Refer to page 2-18 for the locations of the following nuts and bolts on the motorcycle.)
1 Front axle nut
2 Steering stem lock nut
3 Handlebars clamp bolt
4
Tighten Initially at 1,000 km (1 month) and Every
4,000 km (6 months) thereafter.
5 Front fork cap bolt
6 Rear axle nut
7 Engine mounting nut/bolt
8 Brake cam lever nut
9 Front footrest bolt
10 Swing arm pivot nut
ITEM
--kPa
30.0-47.0
25.0-35.0
50.0-60.0
---
23
42.0-66.0
50.0-66.0
7.0
20.0-31.0
27.0-43.0
kg/cm
8.0
8.3
---
2.3
4.5
5.5
0.7
1.3
3.5
3
3.0-4.0
11 Rear torque link nut
12 Rear shock absorber nut
13 Rear sprocket mounting nut
14 Spoke nipple
10.0-16.0
22.0-35.0
18.0-28.0
2.0
1.3
2.9
2.3
0.2
1
9
10
7
13
14
PERIODIC MAINTENANCE 2-19
2
3
5
6
8
11
12
2-20 PERIODIC MAINTENANCE
COMPRESSION PRESSURE CHECK (FD110XC / XCS / XCD / XCSD)
The compression of a cylinder is a good indicator of its internal condition.
The decision to overhaul the cylinder is often based on the results of a compression test.
Periodic maintenance records kept at your dealership should include compression readings for each maintenance service.
COMPRESSION PRESSURE SPECIFICATION
Standard
14.0 kg/cm 2
Version
FD110 XC, XCS
15.0 kg/cm 2 FD110 XC, XCS
Low compression pressure can indicate any of the following conditions:
• Excessively worn cylinder wall
• Worn-down piston or piston rings
• Piston rings stuck in grooves
• Poor seating of valves
• Ruptured or otherwise defective cylinder head gasket
COMPRESSION TEST PROCEDURE
NOTE:
* Before testing the engine for compression pressure, make sure that the cylinder head nuts are tightened to the specified torque values and valves are properly adjusted.
* Have the engine warmed up by idling before testing.
* Be sure that the battery used is in fully-charged condition.
Remove the parts concerned and test the compression pressure in the following maner.
• Support the motorcycle with the center stand.
• Remove the spark plug.
• Fit the compression gauge in the plug hole, while taking care that the connection tight.
• Keep the throttle grip in full-open position.
• While cranking the engine a few seconds with the starter, and record the maximum gauge reading as the compression of that cylinder.
09915-64510: Compression gauge
09915-63310: Adaptor
PERIODIC MAINTENANCE 2-21
OIL PRESSURE CHECK
Check periodically the oil pressure in the engine to judge roughly the condition of the moving parts.
OIL PRESSURE SPECIFICATION
Above 0.1 kg/cm.
2
Below 0.3 kg/cm.
2 at 3,000 r/min., Oil temp. at 60°C
If the oil pressure is lower or higher than the specification, the following causes may be considered.
LOW OIL PRESSURE
• Clogged oil filter
• Oil leakage from the oil passage way
• Damaged O-ring
• Defective oil pump
• Combination of above items
HIGH OIL PRESSURE
• Used an engine oil which is too high viscosity
• Clogged oil passage way
• Combination of above items
OIL PRESSURE TEST PROCEDURE
Check the oil pressure in the following manner.
• Support the motorcycle with the center stand.
• Install the oil pressure gauge with adapter in the position shown in the figure.
• Connect an electric tachometer.
• Warm up the engine as follows: Summer 10 min. at
2,000 r/min. Winter 20 min. at 2,000 r/min.
• After warming up, increase the engine speed to 3,000 r/min.
(with the electric tachometer), and read the oil pressure gauge.
09915-64510: Oil pressure gauge
09915-74531: Adaptor
09900-26006: Tachometer
2-22 PERIODIC MAINTENANCE
AUTOMATIC CLUTCH INSPECTION
This motorcycle is equipped with an automatic clutch.
The engagement of the clutch is Gove med by engine RPM and centrifugal mechanism located in the clutch.
To insure proper performance and longer lifetime of the clutch assembly it is essential that the clutch engages smoothly and gradually. The following inspections must be performed:
1. INITIAL ENGAGEMENT INSPECTION
• Warm up the engine to normal operating temperature.
• Connect an electric tachometer.
• Seated on the motorcycle with the motorcycle on level ground, increase the engine RPM slowly and note the RPM at which the motorcycle begins to move forward.
09900-26006: Tachometer
Engagement r/min: 1,900 - 2,300 r/min
2. CLUTCH “LOCK-UP” INSPECTION
Perform this inspection to determine if the clutch is engaging fully and not slipping.
• Apply the rear brake as firm as possible.
• Briefly open the throttle fully and note the maximum engine
RPM
Do not apply full power for more than 3 seconds or damage to the clutch or engine may occur.
Lock-up r/min: 3,150 – 3,850 r/min
ENGINE
CONTENTS
ENGINE COMPONENTS REMOVABLE WITH THE ENGINE
IN PLACE....................................................................................................... 3-2
ENGINE REMOVAL AND REINSTALLATION.............................................. 3-3
ENGINE REMOVAL ................................................................................ 3-3
ENGINE REINSTALLATION ................................................................... 3-5
ENGINE DISASSEMBLY ............................................................................... 3-6
CYLINDER HEAD.................................................................................. 3-12
GEAR SHIFTING CLUTCH ................................................................... 3-14
CLUTCH COVER AND CLUTCH ADJUSTMENTS .............................. 3-15
ENGINE COMPONENTS INSPECTION AND SERVICE............................. 3-15
FIRST CLUTCH ..................................................................................... 3-15
GEAR SHIFTING CLUTCH ................................................................... 3-16
GEAR SHIFT FORK .............................................................................. 3-17
CRANKCASE BEARING AND OIL SEAL ............................................ 3-18
CYLINDER HEAD RELATED PARTS .................................................. 3-19
ROCKER ARM AND SHAFT................................................................. 3-19
VALVE AND VALVE SPRING DISASSEMBLY.................................... 3-20
CYLINDER HEAD.................................................................................. 3-20
VALVE ................................................................................................... 3-21
CAMSHAFT ........................................................................................... 3-26
CAMSHAFT BEARING ......................................................................... 3-26
CYLINDER DISTORTION...................................................................... 3-27
CYLINDER BORE ................................................................................. 3-27
PISTON DIAMETER .............................................................................. 3-27
PISTON PIN........................................................................................... 3-29
CONROD ............................................................................................... 3-29
STARTER CLUTCH AND STARTER DRIVEN GEAR BEARING ........ 3-30
ENGINE REASSEMBLY .............................................................................. 3-31
ENGINE 3-1
3
3-2 ENGINE
ENGINE COMPONENTS REMOVABLE WITH THE ENGINE IN PLACE
The part listed below can be removed and reinstalled without removing the engine from the frame.
Refer to the page listed in each section for removal and reinstallation instructions.
ENGINE CENTER
Exhaust pipe
Carburetor
Cam chain tensioned adjuster
Cylinder head
Piston
Cylinder
Camshaft
ENGINE LEFT SIDE
Engine sprocket
Magneto cover
Rotor
Gearshift switch
Starter clutch
Starter idle gear
Starter motor
Cam drive chain
Oil filter
Oil filter cover
ENGINE RIGHT SIDE
Clutch cover
First clutch
Primary drive gear
Oil sump filter
Oil pump assembly
Shift cam
Gearshift shaft
Oil pump drive gear
ENGINE 3-3
ENGINE REMOVAL AND
REINSTALLATION
ENGINE REMOVAL
Before taking the engine out of the frame, wash the engine with a steam cleaner. The procedure of engine removal is sequentially explained in the following steps.
• Support the motorcycle with the center stand.
• Remove the oil drain plug 1 to drain out engine oil.
(See page 2-8)
• Open the seat and disconnect the battery( - ) lead wire.
(See page 6-2 and 6-6)
• Remove the leg shields, left and right. (See page 5-1.)
• Remove the frame covers, left and right.
• Remove the footrest bar. See page 2-8.)
88
89
• Remove the exhaust pipe by removing its clamp bolts and muffler mounting bolts. 90 / 91
1
• Remove the engine sprocket cover.
92
• Remove the chain case by loosening four bolts 1 and one bolt 2 .
93
1
2
3-4 ENGINE
• Remove the engine sprocket by loosen the bolt 1 and sprocket lock plate 2 .
• Remove the sprocket.
• Disconnect the several lead wires.
• Magneto lead wire coupler 3 .
• Gearshift indicator lead wire coupler 4 .
• Engine ground coupler
• Disconnect the engine breather pipe.
2
3
1
4
• Disconnect the spark plug cap 5 .
• Disconnect the starter motor ( + ) lead coupler.
• Disconnect the fuel hose 6 .
• Disconnect the fuel tap vacuum hose 7 from the intake pipe.
Gasoline is very explosive. Extreme care must be taken.
• Remove the carburetor with intake pipe.
6 7
5
• Remove the engine mounting bolts and dismount the engine.
ENGINE REINSTALLATION
Reinstall the engine in the reverse of engine removal.
• Install the engine mounting bolts and tighten the nuts to the specification.
Engine mounting nut: 55 N-m (5.5 kg-m)
• Install the drive chain.
The drive chain joint clip should be attached in the way that the slit end will face opposite to the direction of rotation.
• Tighten the exhaust pipe clamp bolts and muffler mounting bolts to specified torque.
Check the wire, cable and hose routing.
(See page 7-10.)
• After remounting the engine, following adjustments are necessary.
* Throttle cable............................. (Page: 2-9)
* Drive chain................................. (Page: 2-10)
* Rear brake pedal....................... (Page: 2-12)
* Idling speed............................... (Page: 2-9)
• Pour 1,000 ml of engine oil SAE 40 graded SF or SG into the engine after overhauling engine. Start up the engine and allow it run for several seconds at idle speed. About one minute after stopping engine, check oil level. If the level is below the “L” line, add oil until the level reaches the “F” line.
(See page 2-8).
UPPER
LOWER
ENGINE 3-5
3-6 ENGINE
ENGINE DISASSEMBLY
The procedure for engine disassembly is sequentially explained in the following steps.
• Remove the gearshift lever and kick starter lever.
• Remove the cam pocket cover.
• Remove the cap and insert the screwdriver into the slotted end of the cam chain tension adjuster and turn it clockwise to lock the spring tension.
NOTE:
When remove the camshaft, the piston must be at (TDC) on compression stroke.
• Remove the cam.
• Loosen and remove the cylinder head nut and bolt.
• Remove the cylinder head.
• Remove the chain guide and gasket.
• Loosen the cylinder nut and remove the cylinder.
• Place a clean rag over the cylinder base to prevent piston pin circlip from dropping into the crankcase and then, remove the piston pin circlip with a long-nose pliers.
• Remove the piston pin and piston.
• Remove the clutch cover.
• Remove the bush 2 , spring 1 and washer 3 shaft gear shift.
1
2
3
ENGINE 3-7
3-8 ENGINE
• Loosen the nut by using the special tool.
09910-20115: Con-rod stopper
• Remove the first clutch assembly, circlip and primary drive gear.
• Remove the clutch bearing.
• Loosen the nut by using the special tool.
09930-40113: Rotor holder
• Loosen the spring mousing bolt by using the special tool
• Remove the clutch pressure and spring clutch
• Remove the clutch sleeve hub 1 .
• Remove the oil pump 2 .
• Remove the oil sump filter 3 .
1
3
2
• Remove the oil washer and oil pump drive gear.
• Remove the shift cam stopper bolt 1 .
• Remove the shift cam pin bolt 2 .
• Remove the shift cam stopper plate, shift cam pin guide and pins.
• Remove the outer bearing, clutch bearing, and gearshift shaft and plate shift cam.
• Remove the starter motor and magneto cover.
1
2
ENGINE 3-9
• Remove the oil filter.
3-10 ENGINE
• Loosen the rotor nut by using the special tool.
09930-44550: Rotor holder
• Loosen the rotor by using the special tool.
09930-34951: Rotor remover
• Loosen the screw and remove the starter clutch plate
• Remove the starter driven gear.
• Remove the starter driven idle gear by removing the circlip 1 and washer.
09900-06107: Snap ring-pliers
• Remove the camshaft drive chain.
• Remove the gearshift switch, gearshift pin and spring.
1
ENGINE 3-11
• Remove the crankcase screws.
• Separate the right and left crankcase by using the special tool.
09920-13120: Crankcase/crank shaft separator
• Remove the kick starter shaft by turning it.
• Remove the gearshift fork shaft, gearshift fork and gearshift cam.
• Remove the transmission assembly.
3-12 ENGINE
• Remove the crankshaft by using a plastic mallet.
• Remove the oil seals and bearings by using the special tools.
09914-79610: Bearing installer
09921-20210: Bearing puller
09930-30102: Sliding shaft
09913-76010: Bearing installer
09925-98221: Bearing installer
09913-75520: Bearing installer
09913-75821: Bearing installer
CYLINDER HEAD
• Remove the chain guide by loosening the bolt.
• Remove the cylinder head right cover and valve inspection caps.
• Remove the rocker arm shafts by using an 8 mm thread bolt.
NOTE:
Intake and exhaust rocker arm shafts differ in the length.
• Remove the rocker arms
• Remove the wave washer
• Remove the spring valve by compress the valve springs with the special tools.
09916-14510: Valve spring compressor
09916-14521: Attachment
• Remove the two valve cotter halves from the valve stem by using the special tool.
09916-14511: Tweezers
• Remove the valve spring retainer, inner spring and outer spring
• Pull out the valve from the other side.
For reassembling the valve and valve springs, refer to page
3-24.
ENGINE 3-13
3-14 ENGINE
• Remove the stem seal 1 with a long nose pliers.
• Take out the spring seat 2 .
For installing the valve spring seat and valve stem seal, refer to pages 3-21 and 22.
• Remove the valve guide by using the special tool.
09916-44310: Valve guide remover
For servicing the valve guide, refer to page 3-21.
GEAR SHIFTING CLUTCH
1
2
CLUTCH COVER AND CLUTCH
ADJUSTMENTS
• Loosen the lock nut and remove clutch release arm.
ENGINE 3-15
CLUTCH ADJUSTMENT
• Loosen the lock nut 1 .
• First, turn the adjusting bolt clockwise by a one turn and turn it counterclockwise until resistance is felt, then turn it clockwise by a 1/8 turn.
• Tighten the lock nut.
ENGINE COMPONENTS INSPECTION
AND SERVICE
FIRST CLUTCH
CLUTCH SHOE INSPECTION
Inspect the linings for crack, uneven wear or burning. Measure the lining thickness with a venire calipers. If any defects are found or measurement exceeds the limit, replace the clutch shoe assembly with a new one.
Service Limit: No groove
09900-20101: Venire calipers
• Clutch springs-visually inspect the clutch springs for stretched coils or broken coils.
Clutch shoes or springs must be changed as a set and never individually.
3-16 ENGINE
• Clutch wheel-inspect visually the condition of the inner clutch wheel surface for scoring, cracks, or uneven wear.
CLUTCH HOUSING INSPECTION
Inspect the inner surface of clutch housing for deep scratches or discoloration caused by burning.
If any defects are found, replace the clutch housing with a new one.
Inspect each roller and one way clutch retainer for abnormal wear or damage.
If any defects are found, replace them as a set.
1 Clutch wheel
2 One way clutch spring
3 One way clutch roller
4 One way clutch retainer
5 One way clutch inner race
GEAR SHIFTING CLUTCH
DRIVE PLATE AND DRIVEN PLATES
Clutch plates in service remain in oily condition as if they were lubricated with oil. Because of this condition, both drive and driven plates are subject to little wearing action and therefore last much longer. Their life depends largely on the quality of oil used in the clutch and also on the way the clutch is operated.
These plates are expendable, they are meant to be replaced when found whom down or the respective limit: use a caliper to check thickness.
09900-20101: Venire calipers
Drive plate
Item
Thickness
Claw width
Service Limit
2.60 (No groove)
11.20 mm
Drive plate distortion
Item
No. 1, 2
Service Limit
0.1 mm
GEAR SHIFT FORK
Using a thickness gauge, check the shifting fork clearance in the groove of its gear. this clearance for each of the two shifting forks plays an important role in the smoothness and positive ness of shifting action. each fork has its prongs fitted into the annular groove provided in its gear. in operation, there is sliding contact between fork and gear axially. too much a clearance is, therefore , liable to clearance check is noted to exceed the limit specified, replace the fork its gear, or both.
09900 – 2088803: thickness gauge
Shift fork – groove clearance
Item Service Limit
No. 1
No. 2
0.5 mm.
Shift fork – groove with
Item
Shift fork thickness
Item
4.5 – 4.6 mm.
4.3 – 4.4 mm.
ENGINE 3-17
3-18 ENGINE
CRANKCASE BEARING AND OIL SEAL
BEARING INSPECTION
Rotate the bearing inner race by finger to inspect for abnormal play, noise and smooth rotation while the bearings are in the crankcase.
Replace the bearing in the following procedure if there is anything unusual.
LEFT CRANKCASE OIL SEAL AND BEARING
DISASSEMBLY
• Remove the left crankcase oil seal by using the special tool.
09913-50121: Oil seal remover
The removed oil seal should be replaced with a new one.
• Remove the left crankcase bearing by using the special tool.
09930-30102: Sliding shaft
09913-76010: Bearing installer
09921-20210: Bearing puller
09925-98221: Bearing installer
NOTE:
If abnormal noise does not occur, it is necessary to remove the bearing.
LEFT CRANKCASE BEARING REASSEMBLY
• Install the left crankcase bearing into the crankcase by using the special tool.
09913-75520: Bearing installer
09913-75821: Bearing installer
09914-79610: Bearing installer
LEFT CRANKCASE BEARING REASSEMBLY
• Install the oil seal into the crankcase using the special tool.
09913-75821: Bearing installer
• Apply a small quantity of SUZUKI SUPER GREASE “A”
TO THE LIP OF OIL SEAL.
99000-25010: SUZUKI SUPER GREASE “A” clearance clearance
RIGHT CRANKCASE BEARING DISASSEMBLY
• Remove the right crankcase bearing by using the special tool.
09913-75821: Bearing installer
09921-20210: Bearing puller
09930-30102: Sliding shaft
RIGHT CRANKCASE BEARING REASSEMBLY
• Install the right crankcase bearing into the crankcase by using the special tool.
09913-70122: Bearing installer
09914-79610: Bearing installer
0991375821: Bearing installer
CYLINDER HEAD RELATED PARTS
ENGINE 3-19
ROCKER ARM AND SHAFT
DISASSEMBLY
• Pull out the intake and exhaust rocker arm shafts by using an
8 mm thread bolt.
3-20 ENGINE
Measure the diameter of rocker arm shaft with a micrometer
Standard: 9.981 - 9.990 mm
09900-20205: Micrometer (0-25 mm)
When checking the valve rocker arm, the inside diameter of the valve rocker arm and wear of the camshaft contacting surface should be checked.
Standard: 10.003-10.018 mm
09900-20605: Dial calipers
REASSEMBLY
• Apply engine oil to the rocker arm shafts.
• Install the rocker arms and shafts to the cylinder.
NOTE:
• The exhaust rocker arm shaft is shorter than the intake one.
• Be sure to bring the threaded side of the rocker arm shaft to the outside when installing it.
• Reassembly the spring rocker arm exhaust only.
VALVE AND VALVE SPRING DISASSEMBLY
• Compress the valve springs with the valve spring compressor.
• Remove the valve cotters from the valve stem.
09916-14510: Valve spring compresso
09916-14521: Attachment
09916-84511: Tweezers
• Remove the valve spring retainer and valve springs.
For reassembling the valve and valve springs, refer to page 3-24
CYLINDER HEAD
DISTORTION
De-carbon the combustion chamber.
Check the gasket surface of the cylinder head for distortion with a straightedge and thickness gauge, taking a clearance reading at several places as indicated. If the largest reading at any position of the straightedge exceeds the limit, replace the cylinder head.
Service Limit: 0.05 mm
09900-20803: Thickness gauge
VALVE
VALVE FACE WEAR
Measure the thickness “T” and, if the thickness is found to have been reduced to the limit, replace the valve.
NOTE:
Visually in sport each valve for wear of its seating face, Replace any valve with an abnormally worm face.
Service Limit : 0.05 mm
VALVE STEM RUNOUT
Support the valve with “V” blocks, as shown, and check its run out with a dial gauge. The valve must be replaced if the run out exceeds the limit.
Service Limit: 0.05 mm
09900-20701: Magnetic stand
09900-20606: Dial gauge (1/100 mm)
09900-21304: V-block (100 mm)
VALVE HEAD RADIAL RUNOUT
Place the dial gauge at right angles to the valve head, and measure the valve head radial run out. If it measures more than limit, replace the valve
Service Limit: 0.03 mm
VALVE STEM DEFLECTION
Lift the valve about 10 mm (0.39 in) from the valve seat. Measure the valve stem deflection in two directions “X” and “Y”, perpendicular to each other, by positioning the dial gauge as shown. If the deflection measured exceeds the limit, (see below) then determine whether the valve or the guide should be replaced with the new one.
Service Limit Intake and exhaust valves: 0.35 mm
VALVE STEM WEAR
If the valve stem is worn down to the limit, when measured with a micrometer, and the clearance is found to be in excess of the limit indicated previously, replace the valve, if the stem is with in the limit, then replace the guide. After replacing valve or guide, be sure to re-check the clearance.
Valve stem O.D.
IN: 4.975-4.990 mm
Standard EX: 4.955-4.970 mm
09900-20205: Micrometer (0-25 mm)
ENGINE 3-21
3-22 ENGINE
VALVE GUIDE SERVICE
• Remove the valve guide with the valve guide remover.
09916-44310: Valve guide remover
• Re-finish the valve guide holes in cylinder head with a reamer
1 and handle 2 .
09916-34580: Valve guide remover (10.8 mm)
09916-34542: Handle
• Fit a ring to each valve guide.
• Lubricate each valve guide with oil, and drive the guide into the guide hole using the valve guide installer.
09916-44310: Valve guide installer
NOTE:
Only oversized valve guides are available as replacement parts.
Be sure to use new valve guide ring and valve guide.
• After fitting the valve guides, re-finish their guiding bores with the reamer 1 and handle. 2 Be sure to clean an oil the guides after reaming.
09916-34570: Valve guide reamer (5.0 mm)
09916-34542: Handle
• Install the valve spring seat 3 . Be careful not to confuse the lower seat with the spring retainer 4 .
4 3
ENGINE 3-23
• Lubricate valve stem seal with oil, and press-fit the seal into position with a finger tip.
Do not reuse the stem seals.
VALVE SEAT WIDTH
• Coat the valve seat uniformly with Prussian blue. Fit the valve and tap the coated seat with the valve face in a rotating manner, in order to obtain a clear impression of the seating contact. In this operation, use the valve lapper to hold the valve head.
• The ring-like dye impression left of the valve face must be continuous-without any break. In addition, the width of the dye ring, which is the visualized seat “width”, must be within the following specification:
Standard
Valve seat width W : 0.9-1.1 mm
If either requirement is not met, correct the seat by servicing it as follows.
VALVE SEAT SERVICE
The valve seat for both intake and exhaust valves are machined to four different angles. (The seat contact surface is cut 45°)
INTAKE
SIDE
EXHAUST SIDE
45°
30°
60°
N -12
N - 126
N - 111
45°
15°
N - 122
N - 121
09916-21110: Valve seat cutter set
(N-111,126,121,122)
09916-24311: Solid pilot: (N-100-5.0)
NOTE:
The valve set contact area must be inspected after each cut.
09916-20630: Valve seat cutter set (N-126)
09916-24311: Solid pilot (N-100-5.0)
09916-21110: Valve seat cutter set
INTAKE EXHAUST
VALVE SEAT VALVE SEAT
3-24 ENGINE
• Insert the solid pilot with a slight rotation. Seat the pilot snugly. Install the 45° cutter, attachment and T-handle.
• Using the 45° cutter, rescale and clean up the seat with one or row turns.
• Inspect the seat by the previously described seat width measurement procedure. If the seat is pitted or burned, additional seat conditioning with the 45° cutter is required
NOTE:
Cut only the minimum amount necessary from the seat to prevent the possibility of the valve stem becoming too close to the rocket arm for correct valve contact angle.
• If the contact area is too high on the valve or if it is too wide, use the 15° cutter (for exhaust side) and30°/60° cutters (for intake side) to lower and narrow the contact area.
• If the contact area is too low or too narrow, use the 45° cutter to raise and widen the contact area. After the desired seat position and width is achieved, use the 45° cutter very lightly to clean up any burrs caused by the previous cutting operations.
DO NOT use lapping compound after the final cut is made. The finished valve seat should have a velvety smooth finish and not a highly polished or shiny finish. This will provide a soft surface for the final seating of the valve which will occur during the first few seconds of engine operations.
• Clean and assemble the head and valve components. Fill the intake and exhaust ports with gasoline to check for leaks. If any leaks, occur, inspect the valve seat and face for burrs or other things that could prevent the valve from sealing.
Always use extreme caution when handling gasoline.
NOTE:
After servicing the valve seats, be sure to check the valve clearance after the cylinder has been reinstalled (See page 2-5)
SOLID PILOT
CONTACT AREA TOO HIGH AND TOO
WIDE ON FACE OF VALVE
CONTACT AREA TOO LOW AND TOO
NARROW ON FACE OF VALVE
ENGINE 3-25
VALVE STEM END CONDITION
Inspect the valve stem end face for pitting and wear. If pitting or wear of the stem end face are present, the valve stem end may be resurfaced, providing that the length 1 will not be reduced to less than 2 mm. If this length becomes less than 2.4 mm, the valve must be replaced. After installing a valve whose stem end has been ground off as above, check to ensure that the face 2 of the valve stem end is above the cotters 3 .
VALVE SPRING
Check the springs for strength by measuring their free lengths and also the force required to compress them. If the limit indicated below is exceeded by the free length reading or if the measured force does not fail within the range specified, replace both the inner and outer springs as a set.
Valve spring free length
Service Limit: 30.09 mm.
09900-20201: Venire calipers
Valve spring tension Standard: 147 nm. HEIGHT 25.80 mm.
VALVE AND VALVE SPRING REASSEMBLY
• Insert the valves, with their stems coated with (SUZUKI
MOLY PASTE) all around and along the full stem length without any break. Similarly oil the lip of the stem seal.
99000-25140: SUZUKI MOLY PASTE
When inserting each valve, take care not to damage the lip of the stem seal.
• Install the valve springs, making sure that the close pitch end
1 of each spring goes in first to rest on the head. The coil pitch of both inner and outer springs very: the pitch decreases from top to bottom, as shown in the illustration.
N
MM.
TOWARDS
HEAD
3-26 ENGINE
• Fit a valve spring retainer, compress the springs with a valve spring compressor and fit the cotter halves to the stem end.
09916-14510: valve spring compressor
09916-14521: Attachment
09916-84511: Tweezers
CAMSHAFT
CAM WEAR
Worn-down cams are often the cause of mistimed valve operation resulting in reduced output power. The limit of cam wear is specified for both intake and exhaust cams in terms of cam height “H” , which is to be measured with a micrometer.
Replace the camshaft if found it worn down to the limit.
Cam height “H”
Intake cam: 27.66 mm
Exhaust cam: 27.47 mm
09900-20202 : Micrometer (25-50 mm)
CAMSHAFT BEARING
Rotate the camshaft bearing outer race by finger to inspect for abnormal play, nose and smooth rotation.
Replace the bearing in the following procedure if there is anything unusual.
• Remove the bearings with a bearing puller.
09913-60910: Bearing puller
NOTE:
Avoid removing the came sprocket flange and right-side bearing from the camshaft unless you really need to do so, for example, removing the damaged right-side bearing.
The removed bearing should be replaced with a new one.
• Press in the bearing to the camshaft with a bearing installer.
09951-76010 : Bearing installer
ENGINE 3-27
NOTE:
* Before reassembling the cam sprocket flange onto the camshaft, apply the internal face of the cam sprocket flange with THREAD LOCK SUPER “1303”.
* This procedure may be performed only once before camshaft replacement is required.
* Installation of the cam sprocket flange requires exact alignment to severe correction of the valve timing.
* The camshaft has automatic DE-COMPRESSOR INSTALLED. (FD 110 XC ONLY) Press in the cam sprocket flange to the camshaft as shown in the illustration.
CYLINDER DISTORTION
Check the gasket surface of the cylinder for distortion with a straightedge and thickness gauge, taking a clearance reading at several places as indicated. If the largest reading at any position of the straightedge exceeds the limit, replace the cylinder.
Service limit: 0.05 mm.
09900-20803: Thickness gauge
CYLINDER BORE
Measure the cylinder bore diameter at six places. If any one of the measurements exceeds the limit, overhaul the cylinder and replace the piston with an oversize, or replace the cylinder.
Service Limit: 53.595 mm
09900-20508: Cylinder bore gauge set
PISTON DIAMETER
Using a micrometer, measure the piston outside diameter at the place 11 mm from the skirt end as shown in Fig. If the measurement is less than the limit, replace the piston.
Service Limit: 53.380 mm
Piston oversize: 0.5, 1.0 mm
09900-20203: Micrometer (50-75 mm)
MM.
3-28 ENGINE
PISTON CYLINDER CLEARANCE
As a result of the above measurement, if the piston to cylinder clearance exceeds the following Limit, overhaul the cylinder and use an oversize piston, or replace both cylinder and piston.
Service Limit: 0.120 mm
PISTON RING-GROOVE CLEARANCE
Using a thickness gauge, measure the side clearance of the 1st and 2nd rings. If any of the clearances exceeds the limit, replace both piston and piston rings.
Piston ring - groove clearance
Service limit: 1 st: 0.180 mm
2nd: 0.150 mm
Piston ring groove width standard 1 st : 1.01-1.03 mm.
2 nd : 1.01-1.03 mm.
Oil : 2.01-2.03 mm.
Piston ring thickness
Standard 1 st and 2nd : 0.97 - 0.99 mm
09900-20803 : Thickness gauge
NOTE:
Using a soft-metal scraper, de-carbon the crown of the piston.
Clean the ring grooves similarly.
PISTON RING END GAP
Fit the ring in the cylinder, and measure each ring end gap using a thickness gauge.
If any ring has an excess end gap, replace the ring.
Piston ring end gap
Service Limit 1 st and 2 nd : 0.50 mm
09900-20803: Thickness gauge
ENGINE 3-29
OVERSIZE RINGS
• Oversize piston ring The following two types of oversize piston ring are used. They bear the following identification numbers.
Piston ring 1 st. and 2nd 0.5 mm: 50
1.0 mm: 100
• Oversize oil ring
The following two types of oversize oil ring are used.
They bear the following identification marks.
Oil ring 0.5 mm: Painted red
1.0 mm: Painted yellow
• Oversize side rail
Just measure outside diameter to identify the side rail as there is no mark or numbers on it.
PISTON PIN
PIN BORE
Using a caliper gauge, measure the piston pin bore inside diameter, and using a micrometer measure the piston pin outside diameter. If the difference between these two measurements is more than the limits, replace both piston and piston pin.
Piston pin bore
Service Limit: 14.030 mm
Piston pin O.D.
Service Limit: 13.980 mm
09900-20605: Dial calipers
09900-20205: Micrometer (0-25 mm)
PAINT
OIL RING
SPACER
CONROD
SMALL END I.D.
Using a caliper gauge, measure the con rod small end inside diameter.
Service Limit: 14.040 mm
09900-20605: Dial calipers
If the con rod small end bore inside diameter exceeds the limits, replace control.
3-30 ENGINE
CONROD DEFLECTION AND CONROD BIG END
SIDE CLEARANCE
Wear on the big end of the con rod can be estimated by checking the movement of the small end of the rod. This method can also check the extent of wear on the parts of the con rod’s big end.
Service Limit: 3.0 mm
09900-20701: Magnetic stand
09900-20606: Dial gauge (1/100 mm)
09900-21304: V-block
Push the big end of the control to one side and measure the side clearance with a thickness gauge.
Standard : 0.10-0.45 mm
Service Limit: 1.00 mm
09900-20803 : Thickness gauge
Where the limit is exceeded, replace crankshaft assembly or reduce the deflection and the side clearance to within the limit by replacing the worn parts-con rod, big end bearing and crank pin etc.
CRANK SHAFT RUNOUT
Support the crankshaft with “V” blocks as shown, with the two end journals resting on the blocks. Position the dial gauge, as shown, and rotate the crankshaft slowly to read the run out. Correct or replace the crankshaft if the run out is greater than the limit.
Service Limit. 0.08 mm
STARTER CLUTCH AND STARTER DRIVEN
GEAR BEARING
STARTER CLUTCH
Install the starter driven gear onto the starter clutch and turn the starter driven gear by hand to inspect the starter clutch for a smooth movement. The gear turns one direction only. If a large resistance is felt to rotation, inspect the starter clutch for damage or inspect the starter clutch contacting surface of the starter driven gear for wear or damage. If they are found to be damaged, replace them with new ones.
STARTER DRIVEN GEAR BEARING
Install the starter driven bearing and gear on to the crankshaft and turn the starter driven gear by hand to inspect the starter driven gear bearing for a smooth rotation and abnormal noise. If abnormal noise does not occur, it is not necessary to replace the bearin
1) STARTER IDLE GEAR
2) PUSH PIECE
3) ROLLER
4) SPRING
5) STARTER CLUTCH HUB SHIM
6) ROTOR
7) STARTER CLUTCH HOLDER
8) SHAFT
9) STARTER GEAR
ENGINE 3-31
ENGINE REASSEMBLY
The engine is reassembled by carrying out the steps of disassembly in the reversed order, but there are a number of steps which demand special description or precautionary measures.
NOTE:
Apply engine oil to each running and sliding part before reassembling.
CRANKSHAFT
• Decide the width between the webs referring to the figure below when rebuilding the crankshaft.
Standard width between webs: 42.0 ± 0.1 mm
• When installing the crankshaft into the crankcase, it is necessary to pull its left end into the left crankcase by using the special tools.
• Apply engine oil to the crankshaft bearings.
09910-32812: Crankshaft installer
09910-32820: Spacer
09911-11310: Attachment
Never install the crankshaft into the crankcase by striking it with a plastic hammer. Always use the special tool, otherwise crankshaft alignment accuracy will be affected
MM.
3-32 ENGINE
CRANKSHAFT SHIM SELECTION
• Degrease the right crankshaft web, shim and inner race of the right crankshaft bearing.
• Place the removed shim 1 on the right crankshaft.
• Put the plastic-gauges (special tool) cut out about 10 mm. on the shim, as shown in the photograph at right.
09900-22302: Plastic gauge
• Install the right crankshaft and tighten the crankcase screws.
• Remove the crankcase screws and separate the crank case into 2 parts, left and right, with the special tool.
(See page 3-10)
09920-13120: Crankcase separator
• Measure the width of compressed plastic-gauge with the envelope scale.
Standard Thrust clearance: 0.01-0.07 mm
• If the thrust clearance is not within specification, select the proper size of shim.
The shim size is printed on the shim surface.
• After selecting the proper size of shim, place it on the right crankshaft.
219
LIST OF SHIMS
Part No.
09181-25051
09181-25052
09181-25051
09181-25054
09181-25055
09181-25056
09181-25057
09181-25058
Shim thickness
0.60 mm
0.65 mm
0.70 mm
0.75 mm
0.80 mm
0.85 mm
0.90 mm
0.95 mm
Part No.
09181-25059
09181-25060
09181-25061
09181-25062
09181-25063
09181-25064
09181-25065
Shim thickness
1.00 mm
1.05 mm
1.10 mm
1.15 mm
1.20 mm
1.25 mm
1.30 mm
KICK STARTER
*(A) : THREAD LOCK SUPER
“1322”
• Align the punch mark 1 of kick starter shaft with punch mark
2 of kick starter
• Turn the kick starter shaft counter-clockwise and then lock the kick starter with kick starter guide.
ENGINE 3-33
3-34 ENGINE
TRANSMISSION
• Seat the circlip in the groove and its ends A should be located as shown in the photo.
• When mounting circlip, pay attention to the direction of the circlip. Fit it to the rounded side against the gear surface
GEAR
CIRCILP
SHAFT
ENGINE 3-35
GEARSHIFT FORK
• NO.1 gearshift fork drive and NO.2 driven
• Install the transmission assembly and gearshift forks
• Install the gearshift cam.
• Install the gearshift fork shafts.
228
NO.1 NO.2
CRANKCASE
• Wipe the crankcase mating surfaces (both surfaces) with a cleaning solvent.
• Fit the dowel pins on to the left half of the crankcase.
• Apply engine oil to con rod big end and T/M. gears.
• Apply BOND NO. 1215 to the mating surface of the left crankcase.
99000-31110: SUZUKI BOND NO.1215
• Assemble the crankcases within few minutes.
NOTE:
• After crankcase crews have been tightened, check if crankshaft rotate smoothly.
• If a large resistance is felt to rotation, try to free the shafts by tapping the drive shaft or countershaft with a plastic hammer as shown in photograph.
3-36 ENGINE
SHIFT CAM RETAINER
• install the shift cam retainer after applying THREAD LOCK
SUPER “1322” to the screws.
99000-32110: THREAD LOCK SUPER “1322”
232
ROTOR AND STATOR
• Install the stator magneto cover.
STARTER CLUTCH
• Apply a small quantity of THREAD LOCK SUPER “1303” to the starter clutch bolts and tighten them to the specified toque by holding the crankshaft.
99000-32030: THREAD LOCK SUPER “1303”
Starter clutch boil: 10 Nm. (1.0 kg-m)
• install the starter idle gear shaft after applying THREAD
LOCK SUPER “1322” to the screws.
99000-32030: THREAD LOCK SUPER “1303”
• install the idle gear and washer.
• Fix the idle gear circlip by using a special tool.
99000-06107: Snap ring pliers
• Install the cam chain.
• Wipe the tapered portion of the crankshaft and also the generator rotor with a cleaning solvent.
• Install the key to the crankshaft.
• Install the rotor assembly after resembling the rotor and starter gear.
• Apply THREAD LOCK SUPER “1303” to the thread and tighten the nut by using the special tool.
99000-32030: THREAD LOCK SUPER “1303”
09930-44512: Generator Rotor Holder
Rotor nut: 80 N.m (8.0 kg-m)
GEARSHIFT
ENGINE 3-37
Kg-m
3-38 ENGINE
• When installing the gearshift lever, align the stopper bolt with gearshift lever relating part.
NOTE:
Install the bearing as shown in the photograph.
241 242
• When install the shift cam pin bolt, apply THREAD LOCK
SUPER “1322” to thread.
99000-32110: THREAD LOCK SUPER “1322”
• When install the shift cam stopper bolt, apply THREAD LOCK
SUPER “1342” to thread.
99000-32050: THREAD LOCK SUPER “1342
244
When installing the cam stopper as illustrated. correct incorrect
OIL PUMP
• When Installing the oil pump, use dowel pin and new O-rings.
• Apply THREAD LOCK “1342” to the oil pump securing screws.
99000-32050: THREAD LOCK SUPER “1342”
GEAR SHIFTING CLUTCH
ENGINE 3-39
• Install the gear shifting clutch by using the circlip.
• Apply engine oil to push piece and drive plates.
3-40 ENGINE
FIRST CLUTCH
• When installing the clutch shoe in the clutch housing align the boss 1 of one way clutch inner with slit 2 of clutch shoes.
• Fix the primary drive gear to clutch housing, circlip by using a special tool.
99000-06107: Snap ring pliers
ENGINE 3-41
• Installing the first clutch to the crankshaft.
• Tighten the first clutch shoe nut to specified torque by using the special tool.
First clutch shoe nut: 5 N-m (5.0 kg-m)
9915-20115: Conrod holder
NOTE:
Clean the oil filter when reassembling it.
CLUTCH ADJUSTMENT
Refer to page 3-14.
PISTON AND RING
• Install space 1 into the bottom ring groove first. Then install both side rails 2 , one on each side of the spacer. The spacer and side rails do not have a specific top or bottom when they are new. When reassembling used parts, install them in their original place and direction
When installing the spacer, be careful not to allow its two ends to overlap in the groove.
• 1st ring and 2nd ring differ in the shape of ring face and the face of 1st ring is chrome-plated whereas that of 2nd ring is not. the color of 2nd ring appears darker than that of the 1st ring.
incorrect correct
3-42 ENGINE
• 1st and 2nd rings have the letter “RN” marked on the top. Be sure to bring the marked side to the top when fitting them to the piston.
• Position the gaps of the three rings as shown. Before inserting piston into the cylinder, check that the gaps are so located.
The following are reminders for piston installation:
• Rub a small quantity of SUZUKI MOLY PASTE on to the piston pin.
• Place a clean rag over the cylinder base to prevent piston pin circlip from dropping into crankcase, and then fit the piston pin circlip with long nose pliers.
• When fitting the piston, turn point mark on the piston head to exhaust side.
Use a new piston pin circlip to prevent circlip failure which will occur with a bent one.
EXHAUST SIDE
CYLINDER
Before mounting the cylinder block, oil the big end and small end of the conrod and the sliding surface of the piston.
• Inspect the oil orifice for cragged.
• Fit dowel pins to crankcase and then fit gasket.
To prevent oil leakage. do not use the old gasket again, always use a new one.
• Hold each piston ring with the piston ring section properly and insert them the cylinder.
• Check to ensure that the piston rings are properly inserted into the cylinder skirt.
• Temporarily tighten the cylinder base nut.
NOTE:
When mounting the cylinder, after attaching camshaft drive chain, keep the camshaft drive chain taut. The camshaft drive chain must not be caught between cam drive chain sprocket and crankcase when crankshaft is rotated.
NOTE:
There is a holder for the bottom end of cam chain guide cast in the crankcase. Be sure that the guide is inserted property or binding of the cam chain and guide may result.
CYLINDER HEAD
• Fit the dowel pins 1 to the cylinder and then, attach the gasket to the cylinder.
To prevent oil leakage. do not use the old gasket again, always use a new one.
• Copper washer 2 is positioned as shown in the photograph.
ENGINE 3-43
3-44 ENGINE
• Tighten the cylinder head nut to the specified torque.
Cylinder head nut: 20 N.m (2.0 kg-m)
Cylinder head nut: 10 N.m (1.0 kg-m)
Cylinder base nut: 10 N.m (1.0 kg-m)
IGNITION TIMING
• Position “T” mark 1 on the magneto rotor with the center of magneto cover hole 2 keeping the camshaft drive chain pulled up ward.
NOTE:
If crankshaft is turned without drawing the camshaft drive chain upward, the chain will be caught between crankcase and cam chain drive sprocket.
• Engage the chain on the cam sprocket and then install the cam sprocket on the camshaft, after align top mark
5 of cam sprocket with top mark 4 of cylinder head.
NOTE:
* Do not rotate magneto rotor while doing this.
When the sprocket is not positioned correctly, turn the sprocket.
264
CAM CHAIN TENSION ADJUSTER
• Install a new gasket and the cam chain tension adjuster to the cylinder with the two bolts and tighten them to the specified torque. chain tension adjuster bolt : 1.2 kg-m
NOTE:
* Before installing the cam chain tension adjuster, lock the tension spring with a screwdriver.
* Before installing the cam chain tension adjuster, turn the crankshaft normal direction to remove the cam chain slack between the crank sprocket and exhaust sprocket
• After installing the cam chain tension adjuster, turn a screwdriver counter clockwise. As the slotted of the cam chain tension adjuster turns, the tension rod is advanced under spring force and pushes the cam chain tension adjuster against the cam chain.
After installing the cam chain tension adjuster, check to be sure that the adjuster work properly by checking the slack of cam chain.
VALVE CLEARANCE
• Check and adjust the valve clearance. Refer to page 2-5 for procedures.
ENGINE 3-45
3-46 ENGINE
SHAFT DRIVE 4-1
FUEL AND LUBRICATION SYSTEM
CONTENTS
FUEL SYSTEM ................................................................................................. 4-2
FUEL TANK, FUEL VALVE, FUEL FILTER AND FUEL LEVEL GAUGE ....... 4-3
FUEL TANK AND FUEL VALVE REMOVAL ......................................... 4-3
FUEL FILTER REMOVAL ....................................................................... 4-3
INSPECTION AND CLEANING .............................................................. 4-4
CARBURETOR ................................................................................................. 4-5
SPECIFICATIONS ............................................................................................ 4-5
I.D. NO. LOCATION ................................................................................ 4-5
CARBURETOR ....................................................................................... 4-6
SLOW SYSTEM ...................................................................................... 4-7
MAIN SYSTEM ........................................................................................ 4-7
STARTER SYSTEM ................................................................................ 4-8
FLOAT SYSTEM ..................................................................................... 4-8
TRANSIENT ENRICHMENT SYSTEM .................................................... 4-9
CARBURETOR REMOVAL .................................................................. 4-10
CARBURETOR JET INSPECTION ....................................................... 4-11
NEEDLE VALVE INSPECTION ............................................................ 4-11
FLOAT HEIGHT ADJUSTMENT ........................................................... 4-12
LUBRICATION SYSTEM ................................................................................ 4-13
OIL PRESSURE .................................................................................... 4-13
OIL FILTER ........................................................................................... 4-13
OIL SUMP FILTER ................................................................................ 4-13
ENGINE LUBRICATION SYSTEM CHART ......................................... 4-14
LUBRICATION SYSTEM ..................................................................... 4-15
4
DRIVELINE/AXLE
4-2 FUEL AND LUBRICATION SYSTEM
FUEL SYSTEM
When tuning the starter motor, a negative pressure is generated in the combustion chamber. This negative pressure draws on the fuel tap diaphragm, (through a passage way in the carburetor intake pipe) and vacuum hose. Due to this, the negative pressure increases behind the fuel tap diaphragm, until it is higher than the valve spring pressure. The fuel valve in the fuel tap is then forced to open (due to this diaphragm operation) and allows fuel to flow into the carburetor float chamber.
FUEL TANK
FUEL HOSE
CARBURETOR
FUEL HOSE
FUEL VALVE
VACUUM HOSE
JET
NEGATIVE PRESSURE
FUEL
FUEL AND LUBRICATION SYSTEM 4-3
FUEL TANK, FUEL VALVE, FUEL FILTER
AND FUEL LEVEL GAUGE
FUEL TANK AND FUEL VALVE REMOVAL
• Remove the leg side shields/frame covers, left and right.
(See page 5-1.)
• Remove the seat by removing its mounting nuts 1 .
• Remove the fuel tank mounting bolts 2 .
• Remove the fuel tank mounting nuts 3 left and right.
• Disconnect the fuel hose 4 and vacuum hose 5 from the fuel valve 6
• Remove the fuel valve mounting bolt
• Disconnect the fuel level gauge lead wire 8 .
• Remove the fuel tank along with the fuel valve.
• Drain the fuel.
Gasoline is very explosive. Extreme care must be taken.
FUEL FILTER REMOVAL
• Remove the left leg side shield/left frame cover.
(See page 5-1.)
• Drain the fuel by disconnecting the fuel hose 9 .
• Remove the fuel filter 0 from the fuel hose 9 .
Gasoline is very explosive. Extreme care must be taken.
4-4 FUEL AND LUBRICATION SYSTEM
FUEL LEVEL GAUGE REMOVAL
• Remove the right leg side shield/right frame cover.
(See page 5-1.)
• Disconnect the fuel level gauge lead wire coupler 1 .
• Remove the fuel level gauge 2 by removing the mounting screws.
For inspecting the fuel level gauge, refer to page 6-18.
INSPECTION AND CLEANING
FUEL FILTER
If the fuel filter is dirty with sediment or rust, fuel will not flow smoothly and loss in engine power may result. Clean the fuel filter with a compressed air.
FUEL VALVE
Connect the vacuum pump gauge to the vacuum port of the fuel valve as shown in the illustration. Apply negative pressure to the fuel valve and blow the fuel inlet port. If air does not flow out, replace the fuel valve with a new one.
Specified vacuum: 22 mm Hg
09917-47910: Vacuum pump gauge
Use a hand operated vacuum pump. Do not apply high negative pressure to prevent the fuel tap damage.
IN
OUT
FUEL AND LUBRICATION SYSTEM 4-5
CARBURETOR
SPECIFICATIONS
ITEM
Carburetor type
Bore size
I.D. No.
Idle r/min
Float height
Main jet (M.J.)
Main air jet (M.A.J.)
Jet needle (J.N.)
Needle jet (N.J.)
Pilot jet (P.J.)
Pilot outlet (P.O.)
Pilot screw (P.S.)
Valve seat (V.S.)
Starter jet (G.S.)
I.D. NO. LOCATION
The carburetor has I.D. Number A stamped on the carburetor body according to its specifications.
SERVICE LIMIT
MIKUNI VM 17
17 mm
09GF
1,500 100 r/min
16 1.0 mm
#92.5
1.65 mm.
4 PA11-2
E-0M
#15
0.7 mm.
1 1/2 turns out
1.5 mm.
# 30
4-6 FUEL AND LUBRICATION SYSTEM
CARBURETOR
1) JET NEEDLE
2) THROTTLE VALVE
3) NEEDLE JET
4) MAIN JET
5) PILOT JET
6) FLOAT
7) NEEDLE VALVE
8) FLOAT PIN
9) THROTTLE VALVE ADJUSTER
SCREW
10) PLUNGER
11) OVERFLOW PIPE
12) PILOT AIR SCREW
13) JET NEEDLE LOCKER
FUEL AND LUBRICATION SYSTEM 4-7
SLOW SYSTEM
This system supplies fuel to the engine operation with the piston valve 5 close or slightly opened. The fuel from the float chamber 6 is metered by the pilot jet 8 . Where it mixes with air coming in the pilot air jet #1 and pilot air passage 9 . This mixture, rich with fuel, then goes up through to pilot air screw 4 . The mixture is discharged into the pilot air passage.
1) VACUUM
2) ----
3) ----
4) PILOT SCREW
5) PISTON
6) FLOAT CHAMBER
7) PILOT AIR JET
8) PILOT JET
9) PILOT AIR PASSAGE
AIR
VACUUM
FUEL
MAIN SYSTEM
This system supplies fuel during engine operation when the piston valve is ¼ -- full open. The fuel passes through the main jet 1 and mixes with air metered by the main air jet 2 . The mixture passes by the clearance between the needle jet 3 and jet needle 4 , and then exits into the main bore after being metered by the jet needle.
AIR
VACUUM
FUEL
4-8 FUEL AND LUBRICATION SYSTEM
STARTER SYSTEM
When the starter plunger 1 is lifted, the fuel metered by the starter jet 2 is mixed with the air coming from the float chamber 3 . The mixture, rich in fuel content, reaches plunger area and mixes again with air coming from the starter air passage 4 .
The two successive mixings of fuel with air are such that a proper fuel/air mixture for starting is produced when the mixture is sprayed out through the starter outlet 5 into the main bore.
AIR
MIXTURE
FUEL
FLOAT SYSTEM
The floats 1 and needle valve 2 are associated with the same mechanism, so that, as the floats move up and down, the needle valve 2 too moves likewise. When the fuel level is up in the float chamber 3 , the floats 1 are up and the needle valve 2 remains pushed up against valve seat. Under this condition, no fuel enters the float chamber(.As the fuel level falls, the floats 1 go down and the needle valve unseats itself to admit fuel into the chamber 3 . In this manner, the needle valve 2 admits and shuts off fuel alternately to maintain a practically constant fuel level inside the float chamber 3 .
FUEL
FUEL AND LUBRICATION SYSTEM 4-9
TRANSIENT ENRICHMENT SYSTEM
The transient enrichment system is a device which keeps fuel/air mixture ratio constant in order not to generate unstable combustion when the throttle grip is returned suddenly during high speed driving. When the throttle valve is closed suddenly, large negative pressure generated on cylinder side works on to a diaphragm 2 . The ball 0 held by the diaphragm 2 closes the air passage 3 , therefore, the fuel/air mixture becomes rich with fuel.
This system is to keep the combustion condition constant by varying the air/flue mixture ratio by controlling air flow from the pilot air jet.
1) -----
2) ----
3) -----
4) PILOT SCREW
5) PISTON VALVE
6) FLOAT CHAMBER
7) PILOT AIR JET
8) PILOT JET
9) PILOT AIR PASSAGE
AIR
VACUUM
MIXTURE
FUEL
4-10 FUEL AND LUBRICATION SYSTEM
CARBURETOR REMOVAL
• Remove the center leg shield. (See page 5-1.)
• Remove the leg shields, left and right. (See page 5-1.)
• Remove the carburetor intake pipe 1 .
• Disconnect the fuel hose 2 and 3 vacuum hose.
• Remove the starter plunger 4 from the carburetor body.
• Loosen the belt 5 .
• Remove the throttle cable assembly 6 .
CARBURETOR DISASSEMBLY
• Remove the carburetor intake pipe by remove the bolt.
• Remove the carburetor capby removing the screws.
09900-09003: Impact driver set
• Remove the o-ring
Replace the o-ring with a new one
FUEL AND LUBRICATION SYSTEM 4-11
• Remove the float assembly 1 by removing the pin 2 .
Do not use a wire for cleaning of passage and jets.
• Remove the main jet 3 .
• Remove the pilot jet 4 .
Do not use a wire for cleaning of passage and jets.
• Remove the pilot air jet 5 .
NOTE:
Before removing the pilot air screw, determine the setting by slowing turning it clockwise and count the number of turns required to lightly seat the screw. This counted number is important when reassembling pilot screw to original position.
CARBURETOR JET INSPECTION
Check following items for any damage or clogging.
* Pilot jet
* Main jet
* Float
* Needle valve
* Main air jet
* Pilot screw
* starter jet
* Gasket and o-ring
* Needle jet air bleeding hole * Pilot outlet and by- pass holes
NEEDLE VALVE INSPECTION
If foreign matter is caught between the valve seat and the needle, the gasoline will continue flowing and cause it to overflow. If the seat and needle are worn beyond the permissibly limits, similar trouble will occur. Conversely, if the needle sticks, the gasoline will not flow into the float chamber. Clean the float chamber and float parts with gasoline. If the needle is worn as shown in the illustration, replace it together with a valve seat.
Clean the fuel passage of the mixing chamber with compressed air.
4-12 FUEL AND LUBRICATION SYSTEM
FLOAT HEIGHT ADJUSTMENT
To check the float height, invert the carburetor body, with the float arm kept free, measure the height A while float arm is just in contact with needle valve by using calipers. Bend the tongue
1 as necessary to bring the height A to this value.
Float height A: 16 ± 1.0 mm
09900-20101: Vernier calipers
JET NEEDLE ADJUSTMENT
• Remove the throttle cable.
• Remove the jet needle locker by screwdriver
• Remove the jet needle.
JET NEEDLE ADJUSTING
• Slide the circlip upper, this mixture is diluted.
• Slide the circlip lower, this mixture is rich.
REASSEMBLY
Reassemble and remount the carburetor in the reverse order of removal and disassembly.
Replace the o-ring with a new one
FUEL AND LUBRICATION SYSTEM 4-13
LUBRICATION SYSTEM
OIL PRESSURE
Refer to page 2-18
OIL FILTER
Refer to page 2-8.
OIL SUMP FILTER
When you replace the engine oil, check to be sure that the oil sump filter is free from any sign of rupture, also wash the oil sump filter clean periodically.
Replace the clutch cover gasket with a new one to prevent oil leakage.
4-14 FUEL AND LUBRICATION SYSTEM
ENGINE LUBRICATION SYSTEM CHART
CAMSHAFT
CYLINDER WALL
IN.ROCKER ARM
AND SHAFT
CYLINDER HEAD
CONROD SMALL END
CONROD BIG END
BEARING
CAM FACES
OIL COOLER
EX.ROCKER ARM
AND SHAFT
CYLINDER
CAM SPROCKET
ADN
CAM DRIVE CHAIN
PISTON AND
PISTON PIN
OIL ORIFICE
CRANKSHAFT
PRIMARY DRIVE
GEAR
FIRST CLUTCH
BY PASS OIL FILTER
OIL PUMP
COUNTER SHAFT
LEFT SIDE BEARING
DRIVESHAFT LEFT
SIDE BEARING
COUNTER SHAFT
GEARS
DRIVE SHAFT
GEARS
CLUTCH
OIL SUMP FILTER
OIL PAN
LUBRICATION SYSTEM
FUEL AND LUBRICATION SYSTEM 4-15
CHASSIS
CONTENTS
EXTERIOR PARTS ........................................................................................ 5-3
REMOVAL ............................................................................................... 5-5
REINSTALLATION.................................................................................. 5-6
REMOVAL AND DISASSEMBLY ........................................................... 5-7
INSPECTION AND DISASSEMBLY ....................................................... 5-8
REASSEMBLY AND REMOUNTING.................................................... 5-10
FRONT WHEEL AND FRONT BRAKE (DISC BRAKE).............................. 5-12
REMOVAL AND DISASSEMBLY ......................................................... 5-12
INSPECTION AND DISASSEMNBLY................................................... 5-12
REASSEMBLY AND REMOUNTING.................................................... 5-13
BRAKE PAD REPLACEMENT ............................................................. 5-14
CALIPER REMOVAL AND DISASSEMBLY......................................... 5-14
CALIPER INSPECTION ........................................................................ 5-15
CALIPER REASSEMBLY AND REMOUNTING ................................... 5-15
MASTER CYLINDER INSPECTION...................................................... 5-17
MASTER CYLINDER REASSEMBLY AND REMOUNTING ................ 5-17
HANDLEBAR ............................................................................................... 5-19
REMOVAL ............................................................................................. 5-19
REASSEMBLY ...................................................................................... 5-20
FRONT FORK AND STEERING .................................................................. 5-21
REMOVAL AND DISASSEMBLY ......................................................... 5-22
INSPECTION ......................................................................................... 5-25
REASSEMBLY AND REMOUNTING.................................................... 5-26
REAR WHEEL AND REAR BRAKE............................................................ 5-29
REMOVAL AND DISASSEMBLY ......................................................... 5-29
INSPECTION AND DISASSEMBLY. .................................................... 5-32
REASSEMBLY AND REMOUNTING.................................................... 5-33
REAR SUSPENSION ................................................................................... 5-35
SWING ARM AND SHOCK ABSORBER ............................................. 5-35
REMOVAL ............................................................................................. 5-35
INSPECTION AND DISASSEMBLY ..................................................... 5-36
REASSEMBLY AND REMOUNTING.................................................... 5-37
CHASSIS 5-1
5
FI SYSTEM DIAGNOSIS 5-2
5-3 CHASSIS
EXTERIOR PARTS
FRONT HANDLEBAR’S COVER
REAR HANDLEBAR’S COVER
CHASSIS 5-4
5-5 CHASSIS
REMOVAL
COVER, FRAME HEAD
• Remove the PLATE, FRONT LICENSE by removing the bolts
1 and 2 .
• Remove the frame head cover.
REAR - VIEW MIRROR
• Remove the rear-view mirrors, left and right, by loosening the lock nuts.
HANDLEBAR’S COVER
• Remove the handlebar’s cover screws.
• Remove the screw and unhook the hooked parts.
• Remove the front-side of the handlebar’s cover by disconnecting each lead wire coupler.
• Remove the handlebar’s cover screws.
• Remove the rear-side of the handlebar’s cover along with the speedometer by disconnecting the speedometer cable and speedometer lead wire couplers.
REINSTALLATION
• Reinstall the removed parts in the reverse order of removal.
FRONT WHEEL AND FRONT BRAKE (DRUM BRAKE)
CHASSIS 5-6
5-7 CHASSIS
REMOVAL AND DISASSEMBLY
FRONT WHEEL
Raise the front wheel of the ground with a jack or wooden block.
• Remove the axle nut 1 .
• Disconnect the speedometer cable 2 .
• Disconnect the front brake cable 3 .
• Remove the axle and front wheel.
FRONT BRAKE
• Remove the front brake panel from the wheel.
• Remove the brake shoes from the brake panel.
• Remove the oil seal 4 .
• Remove the speedometer gear 5 by removing the circlip.
09900-06107: Snap ring pliers
The removed oil seal should be replaced with a new one.
• Remove the brake cam lever bolt/nut 1 .
• Remove the brake cam lever, brake lining wear indicator, washer, spring, O-ring and brake cam. (See page 5-4)
INSPECTION AND DISASSEMBLY
SPEEDOMETER GEARBOX
Turn the speedometer gear 3 and check to see that gear turns smoothly together with the speedometer pinion 4 .
WHEEL BEARING
Rotate the inner race by fingers to inspect for abnormal play, noise and smooth rotation while the bearings are in the wheel.
Replace the bearing in the following procedure if there is anything unusual.
• Insert the adapter 1 of bearing remover to the bearing as shown.
• Insert the wedge 2 of bearing remover to the adapter from the opposite side, lock the wedge in the slit of adapter.
09941-50111 : Bearing remover
Drive out the wheel bearing by knocking the wedge.
Remove the remaining bearing in a similar way with a suitable bar.
The removed bearings should be replaced with new ones.
CHASSIS 5-8
5-9 CHASSIS
AXLE: SHAFT
Using a dial gauge, check the axle shaft for run out and replace it if run out exceeds the limit.
09900-20606: Dial gauge (1/100 mm)
09900-20701: Magnetic stand
09900-21304: V-block set (100 mm)
Service Limit: 0.25 mm
WHEEL
Inspect the wheel run out.
Excessive run out is usually due to worn or loosen wheel bearings and can be reduced by replacing the bearings. If bearing replacement fails to reduce the run out, replace the wheel.
SPOKE NIPPLE
Check to be sure that all nipples are tight, and retighten them as necessary using a spoke nipple wrench.
Spoke nipple: 2.0 N - m (0.2 kg-m)
BRAKE DRUM
Measure the brake drum I.D. to determine the extent of wear and, if the limit is exceeded by the wear noted, replace the drum.
The value of this limit is indicated inside the drum.
09900-20101: Vernier calipers
Service Limit : 110.7 mm
BRAKE SHOE
Check the brake shoe and decide whether it should be replaced or not from the thickness of the brake shoe lining.
Service Limit: 1.5 mm
Replace the brake shoe as a set, otherwise braking performance will be adversely affected.
CHASSIS 5-10
REASSEMBLY AND REMOUNTING
Reassemble and remount the front wheel and front brake in the reverse order of removal and disassembly. Pay attention to the following points:
WHEEL BEARING
• Apply SUZUKI SUPER GREASE "A" to the bearings before installing.
99000-25010: SUZUKI SUPER GREASE "A”
• Using the bearing installer set 1 , press fit the bearing to the wheel. First install the left wheel bearing, then right wheel bearing.
09924-84521 : bearing installer set
The seal side of the bearing should be faced to outside.
LEFT SIDE RIGHT SIDE LEFT SIDE RIGHT SIDE
1) BEARING INSTALLER SET
2) LEFT WHEEL BEARING
3) SPACER
4) RIGHT WHEEL BEARING
CLEARANCE
5-11 CHASSIS
BRAKE CAM/SHAFT
• Apply SUZUKI SUPER GREASE "A" to the brake cam/shaft and pin before installing the brake shoes.
99000-25010 SUZUKI SUPER GREASE "A"
Be careful not to apply too much grease to the cam/shaft and pin. If grease gets on the lining, brake effectiveness will be lost.
BRAKE CAM LEVER
• When installing the brake cam lever and brake lining wear indicator, align the groove 1 on the cam/shaft with the punched mark 2 on the brake lining wear indicator as shown in the illustration.
Brake cam lever nut: 8 N -m (0.8 kg-m)
SPEEDOMETER GEARBOX AND FRONT WHEEL
• Before installing the speedometer gearbox, apply SUZUKI
SUPER GREASE "A" to its dust seal lip.
• Align the drive lugs A to the recesses B of the wheel hub and attach the speedometer gearbox to the wheel hub.
99000-25010: SUZUKI SUPER GREASE "A"
• Connect the speedometer cable 1 and brake 2 .
• Rotate the wheel by hand to inspect for smooth rotation and operation of the speedometer.
Make sure that the drive lugs of the speedometer gear fit to the recesses of the wheel hub or it may cause damage of the speedometer gear.
• Tighten the axle nut 3 to the specified torque.
Axle nut: 43 N-m (4.3 kg-m)
FRONT WHEEL AND FRONT BRAKE (DISC BRAKE)
CHASSIS 5-12
REMOVAL AND DISASSEMBLY
FRONT WHEEL
Remove the front wheel in the same manner of the drum brake type. (See page 5-5.)
FRONT BRAKE
• Flatten the lock portions of the lock washers.
• Remove the brake disc from the wheel by removing its bolts.
INSPECTION AND DISASSEMNBLY
SPEEDOMETER GEARBOX ........ Refer to page 5-6.
WHEEL BEARING ........................ Refer to page 5-6.
AXLE SHAFT ................................ Refer to page 5-7.
FRONT WHEEL ............................ Refer to page 5-7.
SPOKE NIPPLE ............................ Refer to page 5-7.
BRAKE DISC
Visually check the brake disc for damage or cracks.
Measure the thickness with a micrometer.
Replace the disc if the thick ness is less than the service limit or it damage is found.
Service Limit
Brake disc thickness: 3.0 mm
09900-20250: Micrometer (0-25 mm)
5-13 CHASSIS
Measure the run out with a dial gauge.
Replace the disc if the run out exceeds the service limit.
Service Limit
Brake disc run out: 0.3 mm
09900-20606: Dial gauge (1/100 mm)
09900-20701: Magnetic stand
REASSEMBLY AND REMOUNTING
WHEEL BEARING …………………….. Refer to page 5-8.
LEFT SIDE RIGHT SIDE
LEFT SIDE RIGHT SIDE
1) BEARING INSTALLER SET
2) LEFT WHEEL BEARING
3) SPACER
BRAKE DISC
Make sure that the brake disc is clean and free of any greasy matter, Tighten the disc mounting bolts to the specified torque and bend up the lock washer tongues positively to lock its bolts.
Brake disc bolt : 23 N-m (23. Kg-m)
CLEARANCE
SPEEDOMETER GEARBOX AND FRONT WHEEL
Refer to page 5-9.
BRAKE PAD REPLACEMENT
• Loosen the brake pad pins 1 .
Remove the brake caliper by removing the caliper mounting bolts 2 .
Hang the brake caliper on the frame with a string etc., taking care not to bend the brake hose.
• Remove the brake pads by removing the brake pad pins.
* Do not operate the brake lever while dismounting the pads.
* Replace the brake pads as a set, otherwise braking performance will be adversely affected.
CALIPER REMOVAL AND DISASSEMBLY
• Disconnect the brake hose 1 from the caliper by removing the union bolt and catch the brake fluid in a suitable receptacle.
• Remove the caliper mounting bolts 2 .
Never reuse the brake fluid left over from previous servicing and stored for long periods.
• Remove the caliper.
• Remove the brake pad pins 3 .
• Remove the brake pads 4 .
• Remove the brake pad spring 5 .
CHASSIS 5-14
5-15 CHASSIS
• Remove the caliper bracket 6 .
• Place a rag over the piston to prevent its popping out and push out the piston with an air gun.
Do not use high pressure air to prevent piston damage.
• Remove the dust seal 7 and piston seal 8 .
Do not reuse the piston seal and dust seal to prevent fluid leakage..
CALIPER INSPECTION
• Inspect the piston surface and caliper cylinder wall for nicks, scratches or other damage.
• The removed rubber parts should be replaced with new ones.
CALIPER REASSEMBLY AND REMOUNTING
Reassemble the caliper in the reverse order of removal and disassembly. Pay attention to the following points:
• Wash the caliper bore and piston with specified break fluid.
Particularly wash the dust seal groove and piston seal groove.
Specification and classification: DOT 4
• Wash the caliper components with fresh break fluid before reassembly.
• Do not wipe the components with a rag.
• when washing the components, use the specified break fluid. Never use different types of fluid or cleaning solvent such as gasoline, kerosene or the other.
• Replace the piston seal and dust seal with new ones when reassembly. Apply the break fluid to the seals and pistons when installing them.
• Install the pistons seal 2 and dust seals 1 .
• Install the pistons 3 .
• Apply SUZUKI SILICONE GREASE to the caliper axles.
99000:25100: SUZUKI SILICONE GREASE
• Install the break pads.
• Tighten the caliper mounting bolts 4 to the specified torque.
• After touching the break hose union to the stopper A , tighten the union bolt 5 to the specified torque.
Caliper mounting bolt 4 : 26 N-m (2.6 kg-m)
Break hose union bolt 5 : 23 N-m (2.3 kg-m)
NOTE:
Before remounting the caliper, push the piston all the way into the caliper.
MASTER CYLINDER REMOVAL AND DISASSEMBLY
The procedure of master cylinder removal is as follows.
• Rear-view mirrors.
• Handlebar's cover. (See page 5-3.)
• Break light switch lead 1 .
• Break hose union bolt 2 .
The fluid reacts chemically with paint, plastics and rubber materials, etc. and will damage them
• Master cylinder mounting bolts 3 .
CHASSIS 5-16
5-17 CHASSIS
• Break lever 4 .
• Break light switch 5 .
• Remove the reservoir cap 6 and diaphragm 7 .
• Drain break fluid.
• Remove the dust seal 8 .
• Remove the circlip 9 by using the special too.
09900-06108: Snap ring pliers
• Remove the piston / cup 0 and return spring A .
MASTER CYLINDER INSPECTION
Inspect the master cylinder bore for any scratches or other damage.
Inspect the piston surface for any scratches or other damage.
Inspect the piston cup and dust seal for wear or damage.
MASTER CYLINDER REASSEMBLY AND
REMOUNTING
Reassembly the master cylinder in the reverse order of removal and disassembly. Pay attention to the following points:
• Wash the master cylinder components with fresh brake fluid before reassembly. Never use cleaning solvent or gasoline to wash them.
• Do not wipe the components with a rag.
• Apply brake fluid to the cylinder bore and all the components to be inserted into the bore.
Specification and classification: DOT 4
NOTE:
When fitting the circlip, make sure that the sharp edge of the circlip faces outside.
CHASSIS 5-18
• When remounting the master cylinder on the handlebar, align the master cylinder holder's mating surface “A” with punched mark “B” on the handlebar and tighten the upper clamp bolt first as shown.
Tightening torque : 10 N-m. (1.0 kg-m)
NOTE:
Be sure to face the "Up" mark on the holder to the up-side.
Bleed air from the air bleeder valve after reassembling master cylinder. (Refer to page 2-13.)
5-19 CHASSIS
HANDLEBAR
REMOVAL
• Remove the rear-view mirrors. (See page 5-3.)
• Remove the front and rear handlebar's covers. (See pages
5-3 and 5-4.)
• Disconnect the speedometer cable and speedometer lead wire couplers.
• Disconnect the brake light switch lead.
• Remove the left handlebar parts. (Refer to above illustration.)
• Remove the brake master cylinder. (For disc brake: Refer to page 5-14.)
• Remove the right handlebar parts. (Refer to above illustration.)
• Remove the handlebar bol 1 .
• Remove the handlebar clamp bolt 3 .
• Remove the handlebar.
1) handle bar
2)
UV Q R R G T J C P F N G
3) bolt
4) nut
CHASSIS 5-20
REASSEMBLY
Reassembly the handlebar in the reverse order of removal.
Pay attention to the following points:
• Install the handlebar clamp bolt 1 .
• Tighten the handlebar clamp bolt 1 to the specified torque.
Handlebar clamp bolt 1 : 55 N-m (5.5kg-m)
NOTE:
Before installing the front brake lever, apply a small quantity of
SUZUKI SUPER GREASE "A" to the front brake lever pivot.
• Install the front brake cable. (For drum brake)
NOTE:
Apply a small quantity of SUZUKI SUPER GREASE “A” o the front brake cable end. (For drum brake)
99000-25010: SUZUKI SUPER GREASE “A”
• Apply an adhesive agent onto the left handlebar, then install the left handle grip 3 .
• Install the throttle cable 4 .
• Connect the throttle cable end 5 to the throttle grip and install the throttle case 6 , then temporarily tighten the throttle case screw.
NOTE:
Apply a small quantity of SUZUKI SUPER GREASE “A” to the throttle cable end.
After tightening the throttle case screw, make sure that the throttle grip turns smoothly.
(Install the brake master cylinder. (For disc brake: Refer to page 5-16.)
NOTE:
Be sure to face the "UP" mark on the holder to the up-side.
Connect the front brake light switch lead.
Upper clamp bolt
“UP”mark
Master cylinder
Handlebar
Clearance
5-21 CHASSIS
• Connect each lead wire.
• Connect the speedometer cable.
• Install the front and rear handlebar's covers.
FRONT FORK AND STEERING
REMOVAL AND DISASSEMBLY
• Remove the rear-view mirror. (See page 5-3.)
• Remove the left and right leg shields. (See page 5-1.)
• Remove the handle bar
• Remove the front fender 1 .
• Remove the front fender by remove the screw 2 .
• Remove the front fork, left and right by loosen the bolt 3 .
CHASSIS 5-22
5-23 CHASSIS
• Loosen the speedometer cable/front brake cable 1 (For drum brake clamp bolt.)
• Remove the steering stem lock nut 2 by using universal clamp wrench.
09910-60611: Universal clamp wrench
• Remove the washer.
• Remove the steering stem nut 3 .
9910-60611: Universal clamp wrench
• Remove the dust seal 4 and outer upper race.
• Remove the steering stem bracket.
• Remove the upper balls (22 pcs).
• Remove the lower balls (27 pcs).
Do not drop the balls.
• Drive out the steering stem races, upper 5 and lower 6 , with a suitable bar.
• Remove the outer lower race with a thin chisel or screw driver.
• The outer lower race is pressed to the steering stem. If the lower race is removed, replace it with a new one.
• It is not necessary to remove the outer lower race if corrosion, dents or damage on the race have not occurred.
• Remove the spring 1 .
• Invert the fork and stroke it several times to drain out fork oil.
• Hold the fork inverted for a few-minutes to drain oil.
• Remove the dust seal 2 and stopper ring 3 .
• Remove the damper rod bolt with the special tools.
• Remove the inner tube from the outer tube.
09940-34520: T-handle
09940-34561: Attachment "D"
09900-00410: Hexagon wrench set
CHASSIS 5-24
5-25 CHASSIS
• Remove the damper rod 1 from the inner tube.
• Remove the oil seal 2 .
INSPECTION
STEERING RACE AND BALL
• Inspect the upper race, lower race and balls for corrosion, dents or damage.
If dents are noticed on the race, replace the balls and races as a set.
DAMPER ROD RING
Inspect the damper rod ring 1 for wear or damage.
FRONT FORK SPRING
Measure the fork spring free length. If it is shorter than the service limit, replace it with a new one.
Service Limit: 277 mm.
INNER AND OUTER TUBE
Inspect the inner tube sliding surface and outer tube sliding surface for any scuffing
REASSEMBLY AND REMOUNTING
Reassemble and remount the front fork/steering in the reverse order of removal and disassembly. Pay attention to the following points:
* Wash each metal part with cleaning solvent before reassembly.
* Never re-use fork oil left over from the last servicing.
* Replace the oil seal and dust seal with new ones when reassembly
• Apply THREAD LOCK SUPER “1322” to the damper rod bolt and tighten it to the specified torque with the special tools.
Damper rod: 23 N-m (2.3 kg-m)
99000-32110: THREAD LOCK SUPER “1322”
“1322”
09900-00410: Hexagon wrench set
09940-34520: T-handle
09940-34561: Attachment “D”
• Install the oil seal with the special tool.
NOTE:
* Before installing the oil seal apply a small quantity of SUZUKI
SUPER GREASE “A” to the lip of oil seal.
09900-25010: SUZUKI SUPER GREASE “A”
09940-52860: Front fork oil seal installer
• Install the stopper ring and dust seal
Make sure that the stopper ring 2 fitted securely.
CHASSIS 5-26
5-27 CHASSIS
• Pour specified fork oil into the inner tube.
Fork oil type : Fork oil # 10
9000-99044-10 G: SUZUKI FORK OIL # 10
Capacity (each leg): 70 ml
• hold the front fork vertical and adjust the fork oil level with the special tool.
09943-74111 : Fork oil level gauge
Oil level: 116 mm
NOTE:
When adjusting the oil level , remove the fork spring and compress the inner tube fully,.
• Be sure to bring the close-pitch side of fork spring to the top.
• Press in the outer lower race with the special tool.
09940-51710 : Steering race installer
• Press in the steering stem upper race 1 and lower race 2 with the special tool.
09941-34513 : Steering race installer
• Apply SUZUKI SUPER GREASE “A” to the upper and lower races sufficiently and place the balls to the specified quantity.
(Upper): 22 pcs
Number of balls
(Lower): 28 pcs
99000-25010: SUZUKI SUPER GREASE “A”
401
• Install the steering stem bracket 2 .
• Install the dust seal 3 .
• Tighten the steering stem nut 4 to the specified torque.
09940-14920: Steering stem nut wrench
Steering stem nut: 45 N - m (4.5 kg-m)
NOTE:
This adjustment will vary from motorcycle to motorcycle. Make sure that the steering turns smoothly and easily, left to right.
• Install the washer
• Tighten the steering stem lock nut 4 with the special tool.
09940-14920: Steering stem nut wrench
Steering stem lock nut: 30 N-m (3.0 kg-m)
NOTE:
After tightening the stem lock nut, inspect the steering movement again.
• Tighten the front fork clamp bolts and front fork caps to the specified torque.
Front fork clamp bolt: 32 N-m (3.2 kg-m)
• Install the handlebar. (See page 5-18.)
Handlebar clamp bolt: 55N-m (5.5kg-m)
• Install the front wheel. (See page 5-9.)
Axle nut: 43 N-m (4.3 kg-m)
NOTE:
Hold the front fork legs, move them back and forth and make sure that the steering is not loose.
• Install the front and rear handlebar's covers.
(See pages 5-3 and 4.)
CHASSIS 5-28
5-29 CHASSIS
REAR WHEEL AND REAR BRAKE
REMOVAL AND DISASSEMBLY
REAR WHEEL
• Support the motorcycle with the center stand.
• Remove the rear brake adjusting nut 1 .
• Remove the cotter pin and torque link nut 2 .
• Remove the chain case 1 by removing the bolts and screw.
• Remove the rear axle nut 1 .
• Loosen the drive chain adjusting nuts 2 , left and right.
• Draw out the axle shaft.
• Disengage the drive chain from the rear sprocket.
• Remove the rear wheel.
REAR SPROCKET
• Remove the rear sprocket along with its mounting drum out of the wheel hub.
• Remove the rear sprocket dampers out of the wheel hub.
CHASSIS 5-30
5-31 CHASSIS
• Flatten the lock portions of the lock washers.
• Remove the rear sprocket by removing the nuts.
• Remove the spacer out of the sprocket 1 mounting drum.
• Remove the oil seal with the special tool.
09913-50121: Oil seal remover
The removed oil seal should be replaced with a new one.
• Remove the rear sprocket drum bearing in the same manner of the front wheel bearing. (Refer to page 5-6.)
09941-50111: Bearing remover
The removed oil seal should be replaced with a new one.
REAR BRAKE
• Remove the rear brake panel from the wheel.
• Remove the brake shoes from the brake panel.
CHASSIS 5-32
• Remove the brake cam lever bolt/nut 1 .
• Remove the brake cam lever, brake lining wear indicator, washer, O-ring and brake cam. (See page 5-27.)
INSPECTION AND DISASSEMBLY.
WHEEL BEARING ................................. Refer to page 5-6.
AXLE SHAFT ......................................... Refer to page 5-7.
WHEEL .................................................. Refer to page 5-7.
SPOKE NIPPLE ..................................... Refer to page 5-7.
BRAKE DRUM ....................................... Refer to page 5-7.
REAR SPROCKET DRUM BEARING ... Refer to page 5-6
• The inspection of the rear sprocket drum bearing in the same manner of the wheel bearing.
REAR SPROCKET DAMPER
Inspect the cushion for wear and damage.
REAR SPROCKET
Inspect the sprocket teeth for wear. If they are worn as shown, replace the sprockets and drive chain as a set.
NORMAL WEAR EXCESSIVE WEAR
5-33 CHASSIS
REASSEMBLY AND REMOUNTING
Reassemble and remount the rear wheel and rear brake in the reverse order of removal and disassembly. Pay attention to the following points:
WHEEL BEARING
• Apply SUZUKI SUPER GREASE "A" to the bearings before installing.
99000-25010 : SUZUKI SUPER GREASE "A"
• Using the bearing installer set, press fit the bearing to the wheel. First install the right wheel bearing, then left wheel bearings.
09924-84521 : Bearing installer set
• Refer to the following illustration for pressing procedure.
The seal side of the bearing should be faced to outside.
LEFT SIDE RIGHT SIDE LEFT SIDE RIGHT SIDE
1) BEARING INSTALLER SET
2) RIGHT WHEEL BEARING
3) SPACER
4) LEFT WHEEL BEARING
CLEARANCE
REAR SPROCKET DRUM BEARING
• Install the bearing by using the bearing installer.
09913-84510: Bearing installer
NOTE:
Apply grease to the bearing and oil seal lip before assembling rear wheel.
REAR SPROCKET
• Tighten the sprocket mounting nuts to the specified torque and bend up the lock washer tongues positively to lock its nuts.
Rear sprocket nut: 23 N-m (2.3 kg-m)
NOTE:
Face the stamped mark on the sprocket to outside.
BRAKE CAM/SHAFT
• Apply SUZUKI SUPER GREASE “A” to the brake cam/shaft and pin before installing the brake shoes.
99000-25010 : SUZUKI SUPER GREASE "A"
Be careful not to apply too much grease to the cam/shaft and pin. If grease gets on the lining, brake effectiveness will be lost.
BRAKE CAM LEVER
• When installing the brake cam lever and brake lining wear indicator, align the groove 1 on the cam/shaft with the punched mark 2 on the brake lining wear indicators as shown in the illustration.
Brake cam lever nut : 8 N-m (0.8 kg-m)
REAR WHEEL
• Adjust the chain slack after rear wheel installation.
(Refer to page 2-11.)
• Tighten the rear axle nut to the specified torque.
• Tighten both chain adjusting nuts securely.
Axle nut: 45 N-m (4.5 kg-m)
CHASSIS 5-34
5-35 CHASSIS
REAR SUSPENSION
SWING ARM AND SHOCK ABSORBER
REMOVAL
• Remove the rear wheel.(see page 5-27)
• Remove the shock absorber mounting lower bolts 1 , left and right
• Remove the swing arm pivot nut 1 .
• Remove the swing arm by removing its pivot shaft.
INSPECTION AND DISASSEMBLY
SWINGARM BUSHING/SWINGARM
Inspect the swing arm bushing for wear or damage. Inspect the swinger for distortion.
If any defects are found, replace the swing arm bushings and swing arm with new ones.
CHAIN BUFFER
Inspect the chain buffer for wear or damage. If any defects are found, replace the chain buffer with a new one.
SWINGARM PIVOT SHAFT
Using a dial gauge, check the pivot shaft run out and replace it if the run out exceeds the limit.
09900-20606: Dial gauge (1/100 mm, 10 mm)
09900-20701: Magnetic stand
09900-21304: V-block (100 mm)
Service Limit: 0.3 mm
SHOCK ABSORBER
Inspect the shock absorber body for damage and oil leakage. If any defects are found, replace the shock absorber with a new one.
437
Do not attempt to disassemble the rear shock absorber unit. It is unserviceable.
CHASSIS 5-36
5-37 CHASSIS
• Remove the bushing from the swing arm by using a suitable hand-press.
The removed bushing should be replaced with a new one.
REASSEMBLY AND REMOUNTING
Reassemble and remount the swing arm and shock absorber in the reverse order of removal and disassembly, and also carry out the following steps:
SWINGARM BUSHING
• Press the bushing into swing arm pivot by using the special too.
09941-34513: Steering race installer
SHOCK ABSOBER
LEFT SIDE
RIGHT SIDE
ELECTRICAL SYSTEM
ELECTRICAL SYSTEM 6-1
CONTENTS
CAUTIONS IN SERVICING............................................................................ 6-2
LOCATION OF ELECTRICAL COMPONENTS ............................................ 6-4
CHARGING AND LIGHTING SYSTEM ......................................................... 6-5
DESCRIPTION......................................................................................... 6-5
TROUBLESHOOTING............................................................................. 6-6
STARTER SYSTEM....................................................................................... 6-9
DESCRIPTION......................................................................................... 6-9
TROUBLESHOOTING........................................................................... 6-10
STARTER MOTOR REMOVAL AND DISASSEMBLE ......................... 6-11
STARTER MOTOR INSPECTION......................................................... 6-11
STARTER MOTOR REASSEMBLY...................................................... 6-12
STARTER RELAY INSPECTION .......................................................... 6-13
IGNITION SYSTEM...................................................................................... 6-14
DESCRIPTION....................................................................................... 6-14
TROUBLESHOOTING........................................................................... 6-15
INSPECTION ......................................................................................... 6-16
FUEL METER............................................................................................... 6-21
FUEL METER CIRCUIT......................................................................... 6-21
INSPECTION ......................................................................................... 6-21
COMBINATION METER .............................................................................. 6-22
REMOVAL AND DISASSEMBLY ......................................................... 6-22
INSPECTION ......................................................................................... 6-23
LAMPS ......................................................................................................... 6-24
HEADLIGHT AND TURN SIGNAL LIGHT ............................................ 6-24
TAIL/BRAKE LIGHT AND TURN SIGNAL LIGHT ............................... 6-25
TURN SIGNAL RELAY ......................................................................... 6-25
SWITCHES................................................................................................... 6-26
BATTERY..................................................................................................... 6-27
SPECIFICATIONS ................................................................................. 6-27
INTIAL CHARGING ............................................................................... 6-27
SERVICING ........................................................................................... 6-27
RECHARGING OPERATION ................................................................ 6-28
SERVICE LIFE....................................................................................... 6-29
6
6-2 ELECTRICAL SYSTEM
CAUTIONS IN SERVICING
CONNECTOR
• When connecting a connector, be sure to push it in until a click is felt.
• Inspect the connector for corrosion, contamination and breakage in its cover.
COUPLER
• With a lock type coupler, be sure to release the lock before disconnecting it and push it in fully till the lock works when connecting.
• When disconnecting the coupler, be sure to hold the coupler it self and do not pull the lead wires.
• Inspect each terminal on the coupler for being loose or bent.
• Inspect each terminal for corrosion and contamination.
CLAMP
• Clamp the wire harness at such positions as indicated in
“WIRE HARNESS ROUTING” (Refer to page 7-10.).
• Bend the clamp properly so that the wire harness is clamped securely.
• In clamping the wire harness, use care not ot allow it to hang down.
• Do not use wire or any other substitute for the band type clamp.
FUSE
• When a fuse blows, always investigate the cause, correct it and then replace the fuse.
• Do not use a fuse of a different capacity.
• Do not use wire or any other substitute for the fuse.
CLICK
CLICK
CORRECT INCORECT
SEMI-CONDUCTOR EQUIPPED PART
• Be careful not to drop the part with a semi-conductor built in such as CDI unit and regulator/rectifier.
• When inspecting these parts, follow inspection instruction strictly. Neglecting proper procedure may cause damage to these parts.
INCORRECT
CONNECTING BATTERY
• When disconnecting terminals from the battery for disassembly or servicing, be sure to disconnect the negative - terminal first,
• When connecting terminals to the battery, be sureto connect the positive + terminal first.
• If the terminal is found corroded, remove the battery, pour warm water over it and clean with a wire brush.
• Upon completion of connection, apply grease lightly.
• Put a cover over the positive + terminal.
WIRING PROCEDURE
• Route the wire harness properly according to “WIRE HAR-
NESS ROUTING” (Refer to page 7-10).
ADJUSTUSING POCKET TESTER
• Be sure to use positive + and negative probes of the tester properly. Their false use may cause damage in the tester.
• If the voltage and current values are not known, start measuring in the higher range.
• before measuring the resistance and after changing the resistance range, always perform O Ω adjustment.
• Taking a measurement where voltage is applied in the resistance range may cause damage in the tester. When measuring resistance, check to make sure that no voltage is applied there.
• After using the tester, turn the switch to the OFF position.
ELECTRICAL SYSTEM 6-3
A DJUST
6-4 ELECTRICAL SYSTEM
LOCATION OF ELECTRICAL COMPONENTS
1) Battery
2) Fuse
3) Fuel level gauge
4) Turn signal relay
5) Regulator / rectifier
6) Starter relay
7) Ignition coil
8) Generator
9) Starter motor
10) Horn
11) CDI unit
ELECTRICAL SYSTEM 6-5
CHARGING AND LIGHTING SYSTEM
DESCRIPTION
The circuit of the charging and lighting system is indicated in the figure, which is composed of an AC generator, regulator / rectifier unit and battery.
The AC current generated from AC generator is converted by rectifier and is turned into DC current, then it charges the battery. On the other hand, lighting coil supplies A current to the headlight, taillight and meter light under the regulated condition.
AC generator
(Magneto)
Regulator/Rectifier
Night
Day
Fuse
Battery
Turn signal
Light
A B C C
A: Headlight
B: Taillight
C: Meter light
6-6 ELECTRICAL SYSTEM
TROUBLESHOOTING
Battery runs down quickly.
Check accessories which excessively waste electric power.
Not installed
Inspect battery leak current.
(Refer to page 6-6.)
No leak
Inspect charging voltage
Between battery terminals.
(Refer to page 6-6.)
Incorrect
Inspect continuity generator
Coils. (Refer to page 6-7.)
Correct
Inspect continuity generator
Coils. (Refer to page 6-7.)
Correct
Inspect regulator/rectifier.
Coils. (Refer to page 6-8.)
Correct
Inspect wirings.
Installed leak
Correct
• Remove accessories.
• Short circuit of wire harness.
• Loose or disconnected wires.
• Faulty battery.
• Faulty battery.
• Abnormal driving condition.
No continuity
• Faulty generator coils or disconnected lead wires.
Incorrect
• Faulty generator rotor.
Incorrect
• Faulty generator rotor.
Incorrect
• Faulty regulator/rectifier.
Incorrect
• Short circuit of wire harness.
• Poor contact of couplers.
• Faulty battery.
ELECTRICAL SYSTEM 6-7
INSPECTION
BATTERY LEAK CURRENT INSPECTION
• Open the seat.
• Turn the ignition switch to the OFF position.
• Disconnect the battery lead wire.
Note that leakage is indicated if the needle swings even a little when the milliampare meter of the pocket tester is connected between a terminal and lead wire of the battery as shown.
09900-25002: Pocket tester
• Because the leak current might be large, turn the tester to high rang first when connecting an ammeter.
• Do not turn the ignition switch to the ON position when measuring current.
When leakage is found, look for the part where the needle does not swing through the couplers and connectors are removed one by one.
CHARGINNG OUTPUT INSPECTION
• Open the seat.
• Start the engine and keep it running at 5,000 r/min. with lighting switch turned ON.
Measure the DC voltage between the batter + with a pocket tester. If the tester reads under the specified value, inspect the generator coil and regulator / rectifier.
If the pocket tester is set to read current or resistance and a voltage is applied across the test probes, damage will result. Therefore, it is important that the tester knob on the pocket tester be set the proper position before making any measurements.
NOTE:
When making this test, be sure that the battery is fully charged condition.
09900-25002: Pocket tester
Tester knob indication: DC
25VCharging output
Standard: 13.0 V-16.0 V at 5,000 r/min.
BATTERY
TESTER
6-8 ELECTRICAL SYSTEM
GENERATOR (CHARGING/LIGHTING) COIL
INSPECTION
• Remove the center leg shield, leg shields and leg side shields/frame covers. (See page 5-1)
• Disconnect the generator lead wire coupler.
Using the pocket tester, measure the resistance between the lead wires and ground.
If the resistance checked is incorrect, replace the charging/Lighting coil with a new one.
099000-25002: Pocket tester
Charging/Lighting coil resistance
W/R – Ground: 0.5 – 2.0 Ω
Y/W – Ground: 0.3 – 1.5 Ω
Tester knob indication : x1 Ω range
W/R: White with Red tracer
Y/W: Yellow with white tracer
GENERATOR NO-LOAD PERFORMANCE
INSPECTION
• Remove the center leg shield, leg shields and leg side shields/frame covers. (See page 5-1.)
• Disconnect the regulator/rectifier coupler from the regulator/rectifier.
• Turn the lighting switch to OFF position.
• Start the engine and keep it running at 5,000 r/min.
Using a pocket tester, measure the AC voltage between the
W/R lead wire and ground. If the tester reads under the specified value, replace the charging/lighting coil or rotor with a new one.
09900-25002: Pocket tester
Tester knob indication : AC250V
Generator no-load performance:
More than 50V / 5,000 r/min
(When engine is cold)
NOTE:
When making above test, it is not necessary to remove the generator.
W/R
Y/W
W/R
ELECTRICAL SYSTEM 6-9
REGULATOR/RECTIFIER INSPECTION
• Remove the right leg side shield/right frame cover.
(See page 5-1).
• Disconnect the regulator/rectifier coupler.
Using a pocket tester (x1 k Ω range), measure the resistance between the terminals in the following table.
09900-25002: Pocket tester
Tester knob indication : x1 k
Ω
range), measure
1
Unit : Approx. K Ω
+ Probe of tester
2 3 4
11.5-15 1
2
3
4 28-36
: Infinity
NOTE:
As diodes, thyristors are used inside this rectifier, the resistance values will differ between testers.
STARTER SYSTEM
DESCRIPTION
The starter system is shown in the diagram below :namely, the starter motor, starter relay, starter switch, IG switch ad battery.
Depressing the starter switch (on the right handlebar switch box) energizes the relay, causing the contact points to close which connects the starter motor to the battery. The motor draws about 40 amperes to start the engine.
STARTER RELAY
START MOTOR
FUSE
STARTER SWITCH IGNITION SWITCH
SHUT DOWN SWITCH
BATTERY
6-10 ELECTRICAL SYSTEM
TROUBLESHOOTING
Starter motor will not
Check Whether to hear the click noise from the starter relay when the starter button is pushed.
Clicks
No click
Measure he starter relay voltage at the starter relay connectors
(between Y/B + and B/W when the starter button is pushed.
Voltage measured
Check the starter relay.
Incorrect
Not voltage
* C h e c k : i g n i t i o n s w i t c h i s O N p o s i t i o n ,
: B a t t e r y i s n o t d i s c h a r g e d .
: F d i u a s g e n i s o s i n s o t
.
b l o w n b e f o r e t h e
Check whether to run the starter motor when connect the starter motor terminal to the battery + terminal directly. (Do not use thin wire, because a large amount of current flows.
Run Not run
• Faulty starter motor
• Faulty starter relay
• Loose or disconnected starter motor lead wire
• Faulty ignition switch
• Faulty starter button
• Poor contact of connector
• Open circuit in wiring harness
• Faulty starter relay
Starter motor runs, but does not start engine.
Check the CDI unit, ignition coil and generator, (Refer to opages
6-15 and 16)
Correct
Others
Engine does not turnThough starter motor runs.
Incorrect
• Faulty CDI unit
• Faulty ignition coil
• Faulty generator
• Open circuit in wiring harness
• Poor contact of connector
• Faulty starter clutch.
STARTER MOTOR REMOVAL AND
DISASSEMBLE
• Remove the center leg shield and leg shields.
• Disconnect the starter motor lead wire and remove the starter motor by removing the mounting screws.
(Refer to page 3-15)
• Disassemble the starter motor as shown in the illustration.
ELECTRICAL SYSTEM 6-11
STARTER MOTOR INSPECTION
CARBON BRUSH
Inspect the brushes for abnormal wear, crack or smoothness in the brush holder.
In the brush holder.
If the brush has failed, replace the brush sub assy.
1) BOLT (2PCS)
2) O-RING
3) STARTER MOTER CASE
4) O-RING
5) ARMATURE
6) BRUSH SPRING (2PCS)
7) BRUSH (2PCS)
8) BRUSH HOLDER WITH BRUSH
9) HOUSING END
10) O-RING
COMMUTATOR
Inspect the commutator for discoloration, abnormal wear A or undercut.
If the commutator is abnormally worn, replace the armature.
When surface is discolored, polish it with # 400 sand paper and clean it with dry cloth. If there is no undercut, scrape out the insulator 1 with saw blade.
6-12 ELECTRICAL SYSTEM
ARMATURE COIL INSPECTION
Check for continuity between each segment.
Check for continuity between each segment and the armature shaft.
If there is no continuity between the segments or there is continuity between the segments and shaft, replace the armature with a new one.
OIL SEAL INSPECTION
Check the seal lip for damage or leakage.
If any damage is found, replace the bracket.
STARTER MOTOR REASSEMBLY
Reassemble the starter motor in the reverse order of disassembly, Pay attention to the following points:
Replace the O-rings with new ones to prevent oil leakage and moisture.
• Apply SUZUKI SUPER GREASE A to the lip of the oil seal.
99000-25010: SUZUKI SUPER GREASE A
• Apply a small quantity of MOLY PASTE to the armature shaft.
99000-25140: SUKUKI MOLY PASTE
• Apply a small quantity of THREAD LOCK SUPER “1322” to the starter motor housing screws.
9000-32110: THREAD LOCK SUPER “1322”
ELECTRICAL SYSTEM 6-13
STARTER RELAY INSPECTION
• Remove the right leg side shield/right frame cover.
(See page 5-1.)
• Disconnect the lead wire coupler from the starter relay.
• Apply 12 volts to 1 and 2 terminals, inspect the continuity between the terminals, 3 and 4 If the starter relay is in sound condition, continuity is found..
09900-25002: Pocket tester
Tester knob indication : X1 Ω range
Do not apply a battery voltage more than 5 seconds to the starter relay as it may overheat and cause damage to the relay coil.
• Check the coil for “open” , “ground” and ohmic resistance. The coil is in good condition if the resistance is as follows.
9900-25002: Pocket tester
Tester knob indication : X1 Ω range
Starter rely resistance Standard : 60 Ω
6-14 ELECTRICAL SYSTEM
IGNITION SYSTEM
Magneto
Pick-up coil
Ignition timing control circuit
Ignition switch
Fuse
(C)
Ignition coil Transformer
Switen circuit
SCR
Spark plug
Battery
CDI unit
DESCRIPTION
The FD110 XC / XCS / XCD / XCSD engine is equipped with a new type ignition system. This new system minimizes timing fluctuations. It has an “ignition timing control circuit” which accurately controls ignition timing depending on the engine r/min.
There is a transformer in the CDI unit, which steps up the battery voltage to a higher voltage and charges the capacitor (C). An SCR connected to the capacitor becomes conductive (turns on ) when a forward voltage signal is sent to SCR gate allowing the electric energy stored in the capacitor (C) to discharge instantly to the ignition primary coil. This then causes a high voltage to be induced in the secondary coil and a hot spark jumps across the spark plug pap. This ignition timing is controlled by the ignition timing control circuit which processes the signal generator uses to the form an SCR gate signal. The signal is then sent to the
SCR just when the crankshaft has reached the best ignition timing for the current engine revolutions.
ELECTRICAL SYSTEM 6-15
TROUBLESHOOTING
No spark at plug
Check the CDI unit coupler for poor contact.
Correct
Inspect the resistance of charging coil
(W/R and Ground). (Refer to page 6-7.)
*Check : Ignition switch is ON Position.
: Fuse is not blown before the diagnosis.
Looseness
Incorrect
• Poor contact of coupler
• Faulty charging coil
Inspect the resistance of charging coil
(G/W and L/Y). (Refer to page 6-16.)
Incorrect • Faulty pick-up coil
Correct
• Faulty CDI unit
(See page 6-16.)
• Faulty ignition coil
(See page 6-15.)
• Faulty high-tension cord
• Faulty ignition switch
(See page 6-23.)
• Broken wire harness or poor contact of related circuit connectors
6-16 ELECTRICAL SYSTEM
INSPECTION
IGNITION COIL PRIMARY PEAK VOLTAGE
• Remove the spark plug cap.
• Connect a new spark plug to the spark plug and ground it to the cylinder head.
NOTE:
Make sure that the spark plug cap and spark plug are connected properly.
Measure ignition coil primary voltage using the multi circuit tester (DM 200) in the following procedure.
• Connect the multi circuit tester with the peak voltage adaptor as following:
+ Probe: Black / white lead wire
Probe: Blue / white lead wire
NOTE:
Do not disconnect the ignition coil lead wires.
09900-25008: Multi circuit tester set (Digital)
Before using the multi circuit tester and peak volt adaptor, be sure to refer to the appropriate instruction manual.
• Turn the ignition switch to the “on” position.
• Press the starter button and allow the engine to crank for a few seconds, and then measure the ignition coil primary peak voltage.
• Repeat the above procedure a few times and measure the highest ignition coil primary peak voltage.
Tester knob indication : voltage ( v )
Ignition coil primary peak voltage : More then130 V
While testing, do not touch the tester probes and spark plug to prevent receiving an electric shock
* If the voltage is lower then the specified values, inspect the ignition coil.
ELECTRICAL SYSTEM 6-17
IGNITION COIL RESISTANCE
• Disconnect the ignition coil lead wires and spark plug cap.
Measure the ignition coil resistance in both the primary and secondary windings using the multi circuit tester. If the resistance in both the primary and secondary windings is close to the specified values, the windings are in sound condition.
09900-25002: Pocket tester
Tester knob indication : Resistance ( Ω )
Ignition coil resistance
Primary: 0.2 – 1.5 Ω ( + Tap - Tap)
Secondary: 10 – 20 k Ω ( + Tap - spark plug cap)
PICK-UP COIL PEAK VOLTAGE`
• Remove the center leg shield, leg shields and leg side shields/frame covers. (See page 5-1).
NOTE:
Make sure that all of the couplers are connected properly and the battery is fully charged.
• Disconnect the CDI unit coil coupler.
Measure the pickup coil peak voltage in the following procedure.
• Connect the multi circuit tester (DM 200) with the peak volt adaptor as follows.
+ Probe: Blue with yellow tracer lead wire
Probe: Green with white tracer lead wire
Multi circuit tester set (DM 200)
W/L
Terminal
Before using the multi circuit tester and peak volt adaptor, be sure to refer to the appropriate
• Turn the ignition switch to the “ON” position. Measure the pick up coil peak voltage while squeezing the front or rear brake lever and pressing the starter button to turn the engine for a few seconds.
• Repeat the above procedure a few times and measure the highest pickup coil peak voltage.
Tester knob indication : voltage ( v )
Pickup coil primary peak voltage : More then 4 V
Multi circuit tester set (Digital)
6-18 ELECTRICAL SYSTEM
If the peak voltage measured on the CDI unit coupler is lower then the standard value, measure the peak voltage on the pickup coil coupler as follows.
• Disconnect the pickup coil coupler
• Connect the multi circuit tester (DM 200) with the peak volt adaptor as follows.
+ Probe: Blue with yellow tracer lead wire
Probe: Green with white tracer lead wire
Measure the pickup coil peak voltage in the same manner as on the CDI unit coupler.
Tester knob indication : voltage ( v )
Pickup coil primary peak voltage : More then 4 V
Multi circuit tester set (DM 200)
If the peak voltage on the pickup coil coupler is within specification, but on the CDI unit coupler is not within specification, replace the wire harness with a new one. If both peak voltage are out of specification, replace the pickup coil with a new one.
PICKUP COIL RESISTANCE
• Remove the right side frame cover.
• Disconnect the generator coupler
Measure the resistance between the lead wire using the multi circuit tester(DM 200). It the resistance is not within the specified value, the pickup coil must be replaced.
09900-25002: Pocket tester
Tester knob indication: Resistance ( Ω )
Ignition coil resistance: 180 - 280 Ω
(Blue with yellow - Green with white)
ELECTRICAL SYSTEM 6-19
CDI UNIT
• Remove the left leg side shield/left frame cover.
(See page 5-1.)
• Disconnect the CDI unit coupler.
Measure the resistance between the terminals. If the resistance is infinity or less than the specifications, the CDI unit must be replaced.
NOTE:
As capacitor, thyristors, diodes, etc. are used inside this CDI unit, the resistance values will differ when an ohmmeter other than SUZUKI pocket tester is used.
09900-25002 : Pocket tester
Tester knob indication: X1 k Ω range
(A)
(B)
(C)
(D)
(E)
(A)
30-50
30-50
80-120
(B)
+ Probe of tester
(C) (D)
90-120
(E)
80-120 250-400
0
0.6-1.0
11-20
0
11-20
Unit: Approx. K Ω
11-20
11-20
L/Y B/W W/L
G/W O
CON: When the capacitor is discharged state, the needle of tester swings first then return to infinity ( ).
NOTE:
If not sparking at spark plug gap, replace the CDI unit or inspect the magneto coil, ignition coil, spark plug and battery. If the magneto pick-up coil, ignition coil, spark plug and battery checked are correct, the CDI unit may be faulty, replace the CDI unit with a new one.
6-20 ELECTRICAL SYSTEM
SPARK PLUG
• Remove the spark plug.
09930-10121: Spark plug socket wrench set
Carbon Deposit
Check to see the carbon deposit on the plug.
If the carbon is deposited, remove it with a spark plug cleaner machine or carefully using a tool with a pointed end.
Spark Plug Gap
Measure the plug gap with a thickness gauge if it is correct. If not, adjust it to the following gap.
09900-20803: Thickness gauge
Spark plug gap
Standard: 0.6-0.7 mm
Electrode’s Condition
Check to see a worn or burnt condition of the electrode. If it is extremely worn or burnt, replace the plug. Also replace the plug if it has broken insulator, damaged thread, etc.
Heat Range
NGK C 6 HS should be used as the standard. However, the heat range of the spark plug should be selected to meet the requirements of speed, actual load, fuel and etc. Proper heat range would be indicated if all insulators were LIGH BROWN in color.
If they are baked white, they should be replaced with a cold type plug NGK C 7 HS or NIPPONDENSO U 22 FS-U
NGK
NIPPON DENSO
Standard
C 6 HS
U 20 FS-U
Cold type
C 7 HS
U 22 FS-U
Confirm the thread size and reach when replacing the plug. If the reach is too short, carbon will be deposited on the screw portion of the plug hole and engine damage may result.
0.6-0.7 mm .
ELECTRICAL SYSTEM 6-21
FUEL METER
FUEL METER CIRCUIT
Fuel level gauge
B/W
Y/B
O : Orange
B/W: Black with White tracer
Y/B : Yellow with Black tracer
INSPECTION
FUEL LEVEL GAUGE
• Remove the fuel level gauge. (See page 4-3).
Check the resistance of each float position with a pocket tester.
If the resistance measured is incorrect, replace the fuel gauge assembly with new one.
The relation between the position of the fuel gauge float and resistance is shown in the following table.
Float position Height Resistance
A Full
B ½
C Empty
39.3 mm
74.5mm
135.2 mm
4-10 Ω
38 Ω
90-100 Ω
09900-25002: Pocket tester
Tester knob indication: X1 Ω range
Fuel tank
6-22 ELECTRICAL SYSTEM
FUEL METER
• Disconnect the fuel level gauge lead wire coupler.
(See page 4-3).
To test the fuel meter two different checks may be used. The first connect a jumper wire between B/W and Y/B wires coming from the main wiring harness. With the ignition switch turned
ON, the fuel meter should indicate “F”.
Fuel meter is normal if its pointer indicates the E (empty) position when the specified resistance is applied to the circuit and if its pointer indicates the F (full) position when the resistor is changed to 4-10 ohms. If either one or both indicator are abnormal, replace the fuel meter with a new one.
Resistance
Float position
4-10 Ω
Full
90-100 Ω
Empty
When inspection the gauge resistance, be sure to disconnect the battery lead wire, or a pocket tester may be damaged.
COMBINATION METER
REMOVAL AND DISASSEMBLY
• Remove the combination meter.
• Disassemble the combination meter as follows.
O : ORANGE
B/W: BLACK WITH WHITE TRACER
Y/B : YELLOW WITH BLACK TRACER
ELECTRICAL SYSTEM 6-23
<
*U
/
<
<%
G/L : GREEN WITH BLUE TRACER
Y/L : YELLOW WITH BLUE TRACER
W : WHITE
Y/W : YELLOW WITH WHITE TRACER
Y/B : YELLOW WITH BLACK TRACER
B/W : BLACK WITH WHITE TRACER
Y/G : YELLOW WITH GREEN TRACER
Sb : LIGHT BLUE
%:
:
INSPECTION
Using the pocket tester, check the continuity between lead wires.
If the continuity measured is incorrect, replace the respective parts.
09900-25002: Pocket tester
Tester knob indication: X 1 Ω range
POSITION 4
POSITION 3
NOTE:
When making this test, it is not necessary to remove the combination meter.
POSITION 2
486
LIGHT
INDICATOR
LIGHT
HIGH BEAM
LIGHT
POSITION 1 TURN SIGNAL
LIGHT
6-24 ELECTRICAL SYSTEM
LAMPS
HEADLIGHT AND TURN SIGNAL LIGHT
HEADLIGHT BULB REPLACEMENT
• Remove the front handlebar’s cover.
• Push in on the bulb socket, turn it to the left, and pull it out
• Remove the headlight bulb.
When replacing the headlight bulb , do not touch the glass. Grasp the new bulb with a clean cloth.
TURN SIGNAL LIGHT BULB REPLACEMENT
• Remove the turn signal light lenses.
• Pull out each bulb.
Do not overtighten the lens fitting screws.
TAIL/BRAKE LIGHT AND TURN SIGNAL LIGHT
ELECTRICAL SYSTEM 6-25
TAIL / BRAKE LIGHT BULB AND TURN SIGNAL
LIGHT BULB REPLACEMENT
• Remove the tail/brake light lens and turn signal lens.
• Push in on the bulb, turn it to the left, and pull it out.
Do not over tighten the lens fitting screws.
TURN SIGNAL RELAY
The turn signal relay 1 is located the front stem side. If the turn signal light does not light. Inspect the bulb or repair the circuit connection.
If the bulb and circuit connection checked are correct, the turn signal relay may be faulty, replace it with a new one.
NOTE:
Be sure that the battery used is in full-charged condition.
6-26 ELECTRICAL SYSTEM
SWITCHES
Inspect each switch for continuity with the pocket tester. If any abnormality is found, replace the respective switch assemblies with new ones.
09900-25002: Pocket tester
Tester knob indication: X 1 Ω range
IGNITION SWITCH
Position
OFF
Color
ON
R O
HORN BUTTON
Color
Position
PUSH
G B/W
LIGHTING SWITCH
Position
OFF
Color
ON
R
DIMMER SWITCH
Color
Position
HI
LO
YW
TURN SIGNAL SWITCH
Position
L
PUSH
Color
Lg
STARTER BUTTON
Position
OFF
ON
Color
O
W
Sb
O
Y/G
Y
B
FRONT BRAKE SWITCH
Position
OFF
Color
ON
O W/B
REAR BRAKE SWITCH
Color
Position
O
OFF
ON
W/B
GEAR POSITION INDICATION SWITCH
Position
Color GRO
UND
N
1
2
3
4
L W/L R/B G/L Y/L
WIRE COLOR
B : Black
L : Blue
G : Green
Gr : Gray
Sb : Light blue
B/W : Black with White tracer
R/B : Red with Black tracer
W/Y : White with Yellow tracer
Y/W : Yellow with White tracer
R : Red
Lg : Light green
O : Orange
Y : Yellow
W : White
G/L : Green with Blue tracer
W/B : White with Black tracer
Y/L : Yellow with Blue tracer
Y/G : Yellow with Green tracer
ELECTRICAL SYSTEM 6-27
BATTERY
SPECIFICATIONS
Item
Type designation
Capacity
Electric starter with kick starter type
YB 5L-B
12V 15kC
(5Ah/10 HR)
Kick starter type
GM3 –3B
12V 10.8 kC
(3Ah/10HR)
Standard
Electrolyte S.G.
1.28 at 20 °C 1.26 at 20 °C
In fitting the battery to the motorcycle, connect the breather
Pipe to the battery vent.
BATTERY BREATHER HOSE
INTIAL CHARGING
Filling electrolyte
Remove the short sealed tube “A” before filling electrolyte. Fill the battery with electrolyte (dilute sulfuric acid solution with acid concentration of 35.0% by weight, having a specific gravity of
1.28 at 20 °C up to indicated UPPER LEVEL. Electrolyte should be always cooled below 30 °C before filling into battery. Leave battery standing for half an hour after filling. Add additional electrolyte if necessary. Charge battery with current as described in the tables shown below.
Maximum charging current: 0.5 A… YB5L –B
0.3 A .. GM3-3B
Charging time
The charging time for a new battery is determined by the number of months that have elapsed since the date of manufacture. Confirmation for date of manufacture Date of manufacture is indicated by a three-part number 1 , as shown in the photograph, each indicating month, date and year. Near the end of charging period, adjust the specific gravity of electrolyte to value specified. After charging ,adjust the electrolyte level to the UPPER LEVEL with DISTILLED WATER
SERVICING
Visually inspect the surface of the battery container. If any signs of cracking or electrolyte leakage from the sides of the battery have occurred, replace the battery with a new one. If the battery terminals are found to be coated with rust or an acidic white powdery substance, then this can be cleaned away with sandpaper.
6-28 ELECTRICAL SYSTEM
Check the electrolyte level and add distilled water, as necessary to raise the electrolyte to each cell’s
UPPER level. Check the battery for proper charge by taking an electrolyte S.G. reading. If the reading is
1.22 (YB5L-B) or less/1.20 (GM3-3B) or less, as corrected to 20 °C, it means that the battery is still a run-down condition and needs recharging.
NOTE:
First, remove the lead wire.
Months after Manufacturing
Within
6
Within
9
Necessary charging hours
20 30
Within
12
Within
12
40 60
Hydrometer
RECHARGING OPERATION
To read the S.G. on the hydrometer, bring the electrolyte in the hydrometer to eye level and read the graduation on the float scale bordering on the meniscus (curved-up position of electrolyte surface), as shown in figure. Check the reading (as corrected to 20 °C) with chart to determine the recharging time in hour by constant-current charging (which is tenth of the capacity of the present battery). Be careful not to permit the electrolyte temperature to exceed 45 °C, at any time, during the recharging operation. Interrupt the operation, as necessary, to let the electrolyte cool down. Recharge the battery to the specification
Electrolyte specific gravity: 1.28 at 20 °C ..YB5L –B
FD 110 XB517QD)
1.26 at 20 °C ..GM3- 3B
FD 110 XB517QSC
Constant-voltage charging, otherwise called “quick” charging, is not recommendable for it could shorten the life of the battery.
099000-28403: Hydrometer
1.28
1.23
1.18
1.13
1.08
0 2 4 6 8 10 12 14 16 18
Recharging time (hour)
1.27
1.26
1.25
1.24
1.23
1.22
Normal
Recharge
1.21
1.20
1.19
o C
Recharge or Replace
0 5 10 15 20 25 30 35 40 o F 32 41 50 59 68 77 86 95 104
Temperature
1.27
1.26
1.25
1.24
1.23
1.22
Normal
Recharge
1.21
1.20
1.19
o C
Recharge or Replace
0 5 10 15 20 25 30 35 40 o F 32 41 50 59 68 77 86 95 104
Temperature
For GM3-3B type
ELECTRICAL SYSTEM 6-29
SERVICE LIFE
Lead oxide is applied to the pole plates of the battery which will come off gradually during the service. When will come off gradually during the sediment, the battery can not be used any more. If the battery is not charged for a long time, lead sulfate is generated on the surface of the pole plates and will deteriorate the performance (suifation). Replace the battery with new one in such a case. When a battery is left for a long tem without using , it is apt to subject to sulfation. When the motorcycle is not used for more than 1 month
(especially during the winter season), recharge the battery once a month at least.
* Before charging a battery, remove the seal cap from each cell.
* Keep fire and sparks away from a battery being charged.
* When removing a battery from the motorcycle, be sure to remove the terminal first.
6-30 ELECTRICAL SYSTEM
SERVICING INFORMATION 7-1
SERVICING INFORMATION
CONTENTS
TROUBLESHOOTING .................................................................................... 7-2
ENGINE .................................................................................................... 7-2
CARBURETOR ........................................................................................ 7-5
CHASSIS .................................................................................................. 7-6
BRAKES ................................................................................................... 7-7
ELECTRICAL ........................................................................................... 7-8
BATTERY ................................................................................................. 7-9
WIRING DIAGRAM FD 110 (XB517QSC/XB517QD) .................................. 7-10
WIRE HARNESS, CABLE AND HOSE ROUTING....................................... 7-11
WIRE HARNESS ROUTING .................................................................. 7-11
CABLE ROUTING ................................................................................. 7-13
FRONT BRAKE HOSE ROUTING ......................................................... 7-14
FUEL HOSE ROUTING ......................................................................... 7-15
FRONT WHEEL SET UP (DRUM TYPE) ............................................... 7-17
FRONT WHEEL SET UP (DISK TYPE) ................................................. 7-18
REAR WHEEL SET UP .......................................................................... 7-19
SPECIAL TOOLS ................................................................................... 7-20
TIGHTENING TORQUE ................................................................................ 7-23
SERVICE DATA............................................................................................ 7-26
7
7-2 SERVICING INFORMATION
TROUBLESHOOTING
ENGINE
Complaint
Engine will not start, or is hard to start.
Engine stalls easily.
Noisy engine.
Complaint
Symptom and possible causes
Compression too low
1. Out of adjustment valve clearance.
2. Worn valve guides or poor seating of valves.
3. Mistiming valves.
4. Excessively worn piston rings.
5. Worn-down cylinder bore.
6. Too slowly starter motor cranks.
7. Poor seating of spark plug.
Plugs not sparking
1. Fouled spark plug.
2. Wet spark plug.
3. Defective ignition coil.
4. Open or short in high-tension cord.
5. Defective pick-up coil or CDI unit.
No fuel reaching the carburetor
1. Clogged fuel tank air-vent hose.
2. Clogged or defective tap.
3. Defective carburetor needle valve
4. Clogged fuel hose, fuel filter or vacuum hose.
1. Fouled spark plug.
2. Defective pick-up coil or CDI unit.
3. Clogged fuel hose.
4. Clogged jets in carburetor.
5. Out of adjustment valve clearance.
Excessive valve chatter
1. Too large valve clearance.
2. Weakened or broken valve springs.
3. Worn rocker arm or cam surface.
4. Worn and burnt camshaft journal.
Noise seems to come from piston
1. Worn down piston or cylinder.
2. Fouled with carbon combustion chamber.
3. worn piston pin or position pin bore.
4. Worn piston rings or ring grooves.
Noise seems to come from timing chain
1. Stretched chain.
2. Worn sprockets.
3. Not working tension adjuster.
Symptom and possible causes
Remedy
Adjust.
Repair or replace.
Adjust.
Replace.
Replace or rebore.
See electrical section.
Retighten.
Clean.
Clean and dry.
Replace.
Replace.
Replace.
Clean.
Clean or replace.
Replace.
Clean or replace.
Clean.
Replace.
Clean.
Clean.
Adjust.
Adjust.
Replace.
Replace.
Replace.
Replace.
Clean.
Replace.
Replace.
Replace.
Replace.
Repair or replace.
Remedy
SERVICING INFORMATION 7-3
Noise seems to come from clutch
1. Worn or slipping clutch shoe.
2. Worn or slipping clutch drive plate.
Noise seems to come from crankshaft
1. Due to wear ratting bearings.
2. Worn and burnt big-end bearing.
3. Worn and burnt journal bearings.
4. Too large thrust clearance.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace. Or adjust
Thrust shim
Noisy engine.
Slipping clutch.
Turning throttle grip upward makes the engine pick up speed in the normal manner, but the cycle will not pick up speed.
Transmission will not
Shift.
Noise seems to come from transmission
1. Worn or rubbing gears.
2. Badly worn splines.
3. Badly worn bearings.
4. Primary gears worn or rubbing.
1. Worn or damaged clutch shoes.
2. Weakened clutch shoe springs.
3. Worn clutch housing.
1. Slipping first clutch.
2. Slipping gear shifting clutch.
Transmission will not shift back.
Transmission jumps
Out of gear.
Engine idles poorly.
Complaint
1. Broken gearshift cam.
2. Distorted gearshift forks.
3. Worn gearshift pawl.
1. Broken return spring on shift shaft.
2. Shift shafts are rubbing or sticky.
3. Distorted or worn gearshift forks.
1. Worn shifting gears on driveshaft or countershaft.
2. Distorted or worn gearshift fork.
3. Weakened cam stopper spring of gearshift cam.
4. Worn gearshift pawl.
1. Out of adjustment valve clearance.
2. Poor seating of valves.
3. Defective valve guides.
4. Worn rocker arm or cam surface.
5. Too wide spark plug gap.
6. Defective ignition coil.
7. Defective pick-up coil or CDI unit.
8. Out of adjustment in carburetor float- chamber fuel level.
Symptom and possible causes
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace clutch shoe.
Adjust or replace.
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Replace
Adjust.
Replace or repair.
Replace.
Replace.
Adjust or replace.
Replace.
Replace.
Adjust
Remedy
7-4 SERVICING INFORMATION
Engine runs poorly in high speed rage.
Dirty or heavy exhaust smoke.
Engine lacks power.
Engine overheats.
9. Spark plug too cold.
10. Clogged jets in carburetor.
11. Deflective magneto.
1. Weakened valve springs.
2. Worn camshaft or rocker arms.
3. Valve timing out of adjustment.
4. Too narrow spark plug gap.
5. Ignition not advanced sufficiently due to poorly working timing advance circuit.
6. Defective ignition coil.
7. Defective pick-up coil or CDI unit.
8. Too low float-chamber fuel level.
9. Clogged air cleaner element.
10. Clogged fuel hose, resulting in inadequate
fuel supply to carburetor.
1. Too much engine oil in the engine.
2. Worn piston rings or cylinder.
3. Worn valve guides.
4. Scored or scuffed cylinder wall.
5. Worn valves or stems.
6. Defective stem seals.
7. Worn oil ring side rails.
1. Loss of valves clearance.
2. Weakened valve springs.
3. Out of valve timing adjustment.
4. Worn piston rings or cylinder.
5. Poor seating of valves.
6. Fouled spark plug.
7. Incorrect spark plug.
8. Clogged jets in carburetor.
9. Out of float-chamber fuel level adjustment.
10. Clogged air cleaner element.
11. Sucking air from intake pipe.
12. Too much engine oil.
13. Worn rocker arms or shafts.
1. Heavy carbon deposit on piston crown.
2. Not enough oil in the engine.
3. Defective oil pump or clogged oil circuit.
4. Too low in float chambers fuel level.
5. Sucking air from intake pipe.
6. Use incorrect engine oil.
7. Clogged air intake with dust.
Replace by hot type Plug.
Clean.
Replace.
Replace.
Adjust.
Adjust.
Adjust.
Replace CDI unit.
Replace.
Replace
Adjust.
Clean.
Clean and prime.
Drain out excess oil
Replace.
Replace.
Rebore or replace
Replace.
Replace.
Replace.
Adjust.
Replace.
Adjust.
Replace.
Repair.
Clean or replace.
Adjust or replace.
Clean.
Adjust.
Clean.
Retighten or replace.
Drain out excess oil.
Replace.
Clean.
Add oil.
Replace or clean.
Adjust.
Retighten or replace.
Change.
Clean.
SERVICING INFORMATION 7-5
Complaint
Engine overheats.
Symptom and possible causes
1. Heavy carbon deposit on piston crown.
2. Not enough oil in the engine.
3. Defective oil pump or clogged oil circuit.
4. Too low in float chambers fuel level.
5. Sucking air from intake pipe.
6. Use incorrect engine oil.
7. Clogged air intake with dust.
CLUTCH SLIPS OR DRAGS
Clutch slips
Clutch drags
Symptom
First clutch
Gear shifting clutch
Possible cause
1. Excessively worn clutch shoe.
1. Clutch out of adjustment.
2. Excessively worn clutch plates.
First clutch 1. Erratic clutch weight movement.
Gear shifting Clutch 1. Too heavy oil.
2. Clutch out of adjustment.
HARD GEARSHIFTING
Symptom
Engine runs but motorcycle will not start or run.
Possible cause
1. Damaged first clutch.
2. Gear shifting clutch out of adjustment.
3. Seized gears.
4. Damaged countershaft and driveshaft.
Gearshift point is too early. 1. Erratic clutch weight movement.
Gearshift point too late.
Trouble with starting.
1. Excessively worn clutch shoe.
CARBURETOR
Complaint
Trouble with starting.
Idling or low-speed
Symptom and possible causes
1. Clogged starter jet.
2. Clogged fuel pipe.
3. Starter plunger is not operating properly.
4. Starter plunger is not operating property. joint.
5. Not operation properly starter plunger.
6. Air leaking from a joint between starter body and carburetor.
1. Clogged or loose pilot jet, pilot air jet.
2. Air leaking from carburetor’s joint or vacuum hose joint.
3 Clogged pilot outlet or by pass.
4. Not fully closed starter plunger.
Remedy
Clean.
Add oil.
Replace or clean.
Adjust.
Retighten or replace.
Change.
Clean.
Remedy
Replace.
Adjust.
Replace.
Replace.
Replace with proper
Grade oil.
Adjust.
Remedy
Replace clutch shoe.
Adjust.
Replace.
Replace.
Replace clutch shoe.
Replace clutch shoe.
Remedy
Clean.
Clean.
Check and adjust.
Check and adjust.
Check and adjust. Or replace.
Clean and retighten.
Check and clean.
Check and replace.
Check and clean.
Check and clean.
7-6 SERVICING INFORMATION
Complaint
Medium-or high
Speed trouble.
Overflow and fuel
Level fluctuations.
Symptom and possible causes
1. Clogged main jet or main air jet.
2. Clogged needle jet.
3. Not operating properly throttle valve.
4. Clogged fuel filter.
5. Clogged fuel tank air vent hose.
1. Worn of damaged needle valve.
2. Broken spring in needle valve.
3. Not working properly float.
4. Foreign matter has adhered to needle valve.
5. Too high or low fuel level.
Remedy
Check and clean.
Check and clean.
Check throttle valve For operation.
Check and clean.
Check and clean.
Replace.
Replace.
Check and adjust.
Clean.
Adjust float height.
CHASSIS
Complaint
Heavy steering.
Wobbly handlebars.
Wobbly front wheel.
Symptom and possible causes
1. Over tightened steering stem nut.
2. Broken bearing in steering stem.
3. Distorted steering stem.
4. Not enough pressure in tires.
1. Loss of balance between right and left front forks.
2. Distorted front fork.
3. Distorted front axle or crooked tire.
1. Distorted wheel rim.
2. Worn front wheel bearings.
3. Defective or incorrect tire.
4. Loose axle nut.
5. Incorrect front fork oil level.
6. Loose wheel spoke.
Front suspension too soft. 1. Weakened springs.
2. Not enough fork oil.
Front suspension too stiff. 1. Too viscous fork oil.
2. Too much fork oil.
Noisy front suspension. 1. Not enough fork oil.
2. Loose bolts on suspension.
Wobbly rear wheel exhaust smoke.
1. Distorted wheel rim.
2. Worn rear wheel bearing.
3. Defective o incorrect tire.
4. Worn swing arm bushing.
5. Loose axle nut or engine mounting nut.
6. Loosen wheel spokes.
7. Loosen nut or rear shock.
Remedy
Adjust.
Replace.
Replace.
Adjust.
Replace.
Repair. or replace.
Replace.
Replace.
Replace.
Replace.
Retighten.
Adjust.
Retighten.
Replace
Replenish.
Replace.
Drain excess oil.
Replenish.
Retighten.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
Replace.
SERVICING INFORMATION 7-7
Complaint Symptom and possible causes
Rear suspension too soft. 1. Weakened shock absorber spring.
2. Leakage oil of shock absorber.
Noisy rear suspension 1. Loose bolts on shock absorber.
2. Worn swing arm bushing.
Remedy
Replace.
Replace.
Retighten.
Replace.
BRAKES
Complaint
Insufficient brake power.
Brake squeaking,
Excessive brake lever stroke.
Leakage of brake fluid.
No sparking or poor become fouled with carbon.
Symptom and possible causes
1. Leakage of brake fluid from hydraulic system.
2. Worn pads.
3. Worn disc.
4. Air in hydraulic system.
5. Worn shoe.
6. Friction surfaces of shoes are dirty with oil.
7. Excessively worn drum.
8. Too much brake lever play.
1. Carbon adhesion on pad surface.
2. Titled pad.
3. Damaged wheel bearing.
4. Loosen front-wheel axle or rear-wheel axle.
5. Worn pads.
6. Foreign material in brake fluid.
7. Clogged return port of master cylinder.
8. Brake shoe surface glazed.
9. Worn shoe.
1. Air in hydraulic system.
2. Insufficient brake fluid.
3 Improper quality of brake fluid.
4. Worn brake cam lever.
5. Excessively worn shoes and/or drum.
1. Insufficient tightening of connection joints.
2. Cracked hose.
3. Worn piston and/or cup.
1. Defective ignition coil or CDI unit.
2. Defective spark plug.
3 Defective pick-up coil.
Remedy
Repair or replace.
Replace.
Replace.
Bleed air.
Replace.
Replace.
Replace.
Adjust.
Repair surface with sandpaper.
Modify pad fitting or replace.
Replace.
Tighten to specified torque.
Replace.
Replace brake fluid.
Disassemble and clean master cylinder.
Repair surface with sandpaper.
Replace.
Bleed air.
Replenish fluid to Specified level; bleed air.
Replace with correct fluid.
Replace.
Replace.
Tighten to specified torque.
Replace.
Replace piston and/or cup.
Replace.
Replace.
Replace.
7-8 SERVICING INFORMATION
ELECTRICAL
Complaint
Spark plug soon become fouled with carbon.
Spark plugs become fouled too soon.
Spark plug electrodes overheat or burn.
Generator does not charge.
Generator does charge, but charging rate is below the specification.
Generator overcharges.
Unstable charging
Starter button is not effective.
Symptom and possible causes
4. Loose connection of lead wire.
1. Mixture too rich.
2. Idling speed set too high.
3. Incorrect gasoline.
4. Dirty element in air cleaner.
5. Too cold spark plug.
1. Lead wire insulation frayed due to vibration, resulting in intermittent shorting.
2. Internally shorted generator.
3. Defective regulator/rectifier.
1. Run down battery.
2. Defective switch contacts.
3. Not seating properly brushes on commutator in starter motor.
4. Defective starter relay.
Remedy
Connect/tighten.
Adjust carburetor.
Adjust carburetor.
Change.
Clean.
Replace with hot type
Plugs.
Replace.
Replace.
Replace.
1. Worn piston rings.
2. Worn piston or cylinder.
3. Excessive clearance of valve stems in valve guides.
4. Worn stem oil seal.
1. Too hot spark plug.
2. Overheated the engine.
3. Loose spark plug.
4. Too lean mixture.
1. Open or short lead wires, or loose lead connections.
2. Shorted, grounded or open generator coils.
3. Shorted or punctured regulator/rectifier.
1. Lead wires tend to get shorted or open-circuited or loosely connected at terminals.
2. Grounded or open-circuited stator coils or generator.
3. Defective regulator/rectifier.
4. Defective cell plates in the battery.
5. Not enough electrolyte in the battery.
1. Internal short-circuit in the battery.
2. Damaged or defective resistor element in the regulator/rectifier.
3. Poorly grounded regulator/rectifier.
Replace.
Replace with cold type plugs.
Tune up.
Retighten.
Adjust carburetor.
Repair or replace or retighten.
Replace.
Replace.
Repair or retighten.
Replace.
Replace. Replace the battery. Add distilled water to the upper level.
Replace the battery.
Replace.
Cleaned and tighten ground connection.
Repair or replace.
Replace.
Replace.
Repair or replace.
Replace.
Repair or replace.
Replace.
SERVICING INFORMATION 7-9
BATTERY
Complaint
“Sulfation”, acidic white powdery substance or spots on surfaces of cell plates.
Symptom and possible causes
1. Not enough electrolyte.
2. Battery case is cracked.
3. Battery has been left in a run down condition for a long time.
Remedy
Add distilled water, if the battery has not bee n damaged and “sulfation” has not advanced too far, and recharge. Replace the battery. Replace the battery.
Battery runs down quickly.
4. Contaminated electrolyte (Foreign matter has entered the battery and become mixed with the electrolyte).
1. The charging method is not correct.
2. Cell plates have lost much of their active material as a result of over charging.
3. A short-circuit condition exists within the battery due to excessive accumulation of sediments caused by the high electrolyte
S.G.
If “sulfation” has not advanced too far, try to restored the battery by replacing the electrolyte, recharging it fully with the battery detached from the motorcycle and then adjusting electrolyte S.G.
Check the generator, regulator/rectifier and circuit connections, and make necessary adjustments to obtain specified charging operation. Replace the battery, and correct the charging system.
Replace the battery
Reversed battery polarity. The battery has been connected the wrong way round in the system, so that is being charged in the reverse direction.
Battery Sulfation”
4. Electrolyte S.G. is too low.
5. Contaminated electrolyte.
6. Battery is too old.
1. Charging rate too low or too high. (When not in use battery should be recharged at least once a month to avoid sufation.)
2. Battery electrolyte excessive or insufficient, or its specified gravity too high or too low.
3. The battery left unused for too long in cold climate.
Battery discharges too rapidly. 1. Dirty container top and sides.
1. Dirty container top and sides.
2. Impurities in the electrolyte or electrolyte
S.G. is too high.
Recharge the battery fully and adjust electrolyte,
S.G. Replace the battery.
Replace the battery and be sure to connect the battery properly.
Replace the battery.
Keep the electrolyte up the prescribed level, or adjust the S.G. by consulting the battery maker’s directions.
Replace the battery, if badly sulfated.
Clean.
Change the electrolyte by consulting the battery maker’s directions.
7-10 SERVICING INFORMATION
WIRING DIAGRAM FD 110 (XB517QSC/XB517QD)
SERVICING INFORMATION 7-11
WIRE HARNESS, CABLE AND HOSE ROUTING
WIRE HARNESS ROUTING
PASS THE WIRINGUNDER
T HE F UE L HO S E
IG NIT IO N S W IT C H C LAMP
R E AR B R AK E L IG HT
S W IT C H
F UE L G AUG E
B AT T E R Y ( + ) T E R MINAL C O V E R
B AT T E R Y ( + ) T E R MINAL
F US E B O X
S T AR T E R R E L AY
B AT T E R Y B R E AT HE R
P IP E
S T O P L AMP S W IT C H
C DI UNIT
S T AR T E R MO T O R
R E G UL AT O R / R E C T IF IE R
C LAMP
G R O UND
7-12 SERVICING INFORMATION
MAGNETO LEAD WIRE ROUTING
PICK-UP COIL
MAGNETO LEAD WIRE
ENGINE GROUND WIRE
MAGNETO STATOR
GROMMET
CLAMP
8.0 KG-M
GROMMET
GEAR POSITION
INDICATOR
SERVICING INFORMATION 7-13
CABLE ROUTING
S T AR T E R C AB L E
S T AR T E R L E V E R
VIEW A
S T AR T E R C AB L E
C L AMP
A
C L AMP
S P E E DO ME T E R C AB L E
VIEW B
F R O NT B R AK E C AB L E
F R O NT B R AK E C AB L E
S P E E DO ME T E R C AB L E
7-14 SERVICING INFORMATION
FRONT BRAKE HOSE ROUTING
C L AMP
C AR B U R E T O R
T H R O T T L E C AB L E
S T AR T E R C AB L E
F R O NT B R AK E C AB L E
S T AR T E R C AB L E
S T AR T E R C AB L E
C L AMP
S P E E DO ME T E R C AB L E
C L AMP
FUEL HOSE ROUTING
CLAMP
FUEL TANK
SERVICING INFORMATION 7-15
7-16 SERVICING INFORMATION
BATTERY
FUEL TANK
BATTERY BREATHER HOSE
FRONT WHEEL SET UP (DRUM TYPE)
SERVICING INFORMATION 7-17
7-18 SERVICING INFORMATION
FRONT WHEEL SET UP (DISK TYPE)
REAR WHEEL SET UP
SERVICING INFORMATION 7-19
114.8 mm.
7-20 SERVICING INFORMATION
SPECIAL TOOLS
09900-00401
“L” type haxagon wrench set
09900-00410
Hexagon wrench set
09900-06107
Snap ring pliers
09900-06108
Snap ring pliers
09900-09003
Impact driver set
09900-20101
Vernier calipers
(1/20 mm, 150 mm)
09900-20202
Micrometer
(1/100 mm,
25-50 mm)
09900-20203
Micrometer
(1/100 mm,
50-75 mm)
09900-20205
Micrometer
(1/1000 mm,
0-25 mm)
09900-20508
Cylinder gauge set
(1/100 mm,
40-80 mm)
09900-20605
Dial calipers
(1/100 mm, 10-34 mm)
09900-20606
Dial gauge
(1/100 mm, 10 mm)
09900-20701
Magnetic stand
09900-20803
Thichness gauge
09900-20805
Tire depth gauge
09900-21304
V-block set
(100 mm)
0900-22302
Plastigauge
09900-25002
Pocket tester
0900-26006
Tacho meter
0900-28108
Electro tester
09900-28403
Hydrometer
09910-20115
Con-rod holder
09910-32812
Crankshaft installer
09910-32820
Crankshaft installer spacer
09910-60611
Universal clamp wrench
09911-11310
Crankshaft installer attachment
09913-50121
Oil seal remover
09913-60910
Bearing puller
09913-70122
09913-75520
Bearing installer
09913-75821
Bearing installer
SERVICING INFORMATION 7-21
09913-84510
Bearing installer
09913-76010
09914-79610
Bearinginstaller
09915-64510
Compression gauge
09915-63310
(Adaptor)
09915-74510
Oil pressure gauge
09915-44531
Oil pressure gauge adaptor
09916-14510
Valve spring compressor
09916-14521
Valve lifter attachment
09916-21110
Valve seat cutter set
09916-20630
Valve seat cutter head (n-126)
09916-24311
Solid pilot
(N-100-5.0)
09916-34542
Valve guide reamer handle
09916-34570
Valve guide reamer
(5.0 mm)
09916-34580
Valve guide reamer
(10.8 mm)
09916-44310
Valve guide remover/ installer
09916-84511
Tweezers
09917-14910
Vale clearance adjusting driver
099-17-47910
Vacuum pump gauge
09920-13120
Crankcase separator
09920-53722
Clutch sleeve hub holder
09921-20210
Bearing remover
09922-55131
Bearing installer
09923-74510
09923-73210
Bearing puller
(17-20 mm)
09924-84521
Bearing installer set
09925-98221
Bearing installer
09930-10121
Spark plug socket wrench set
09930-30102
Sliding shaft
09930-34951
Rotor remover
09930-44550
Generator rotor holder
09940-34520
T-Handle
09940-34561
Front fork assembling tool attachment “D”
7-22 SERVICING INFORMATION
09940-14920
Steering stem nut wrench
09940-52860
Front fork oil seal installer set
09940-51710
Steering race installer
09940-60113
Spoke nipple wrench
09941-34513
Steering outer race installer
09941-50111
Bearing remover
09941-74910
Steering bearing installer
09943-74111
Front fork oil level gauge
09951-16080
Bearing installer
NOTE:
When ordering the special tool please confirm whether it is available of not.
TIGHTENING TORQUE
ENGINE
Cylinder head nut
Cylinder head bolt
ITEM
Cam sprocket bolt
Cam chain tensioner bolt
Starter clutch bolt
Spark plug
Valve clearance inspection cap bolt
Cylinder head right cover bolt
Cylinder head left cover bolt
Cam chain guide bolt
First clutch nut
Second clutch nu
Shift arm stopper bolt
Magneto rotor nut
Engine oil drain plug
Exhaust pipe bolt
Muffler mounting bolt
Engine mounting bolt
Oil filter cap bolts
Sprocket nut
N-m
18.0-22.0
8.0-12.0
9.0-11.0
8.0-12.0
14.0-16.0
10.0-12.0
10
8.0-12.0
8.0-12.0
8.0-12.0
40.0-60.0
40.0-60.0
19
70.0-90.0
15.0-20.0
8.0-12.0
26
55
8.0-12.0
23
SERVICING INFORMATION 7-23
0.8-1.2
0.8-1.2
0.8-1.2
4.0-6.0
4.0-6.0
1.9
7.0-9.0
1.5-2.0
Kg-m
1.8-2.2
0.8-1.2
0.9-1.1
0.8-1.2
1.4-1.6
1.0-1.2
1.0
0.8-1.2
2.6
5.5
0.8-1.2
2.3
7-24 SERVICING INFORMATION
CHASSIS
ITEM
Front axle/nut
Steering stem lock nut
Handlebar clamp bolt
Handlebar mounting nut
Front fork cap bolt
Front fork clamp bolt
Front brake master cylinder bolt
Front brake hose union bolt
Front brake caliper mounting bolt
Front brake air bleeder valve
Rear axle nut
Engine mounting nut/bolt
Brake cam lever nut
Front footrest bolt
Swing arm pivot nut
Rear torque link nut
Rear shock absorber bolt
Rear sprocket mounting nut
Spoke nipple
Brake disc bolt
N-m
30.0-47.0
25.0-35.0
50.0-60.0
13
45
25.0-40.0
8.0-12.0
23
18.0-28.0
8
42.0-66.0
50.0-60.0
7
20.0-31.0
27.0-43.0
10.0-16.0
22.0-35.0
18.0-28.0
2
18.0-28.0
2.3
1.8-2.8
0.8
4.2-6.6
5.0-6.0
0.7
2.0-3.1
2.7-4.3
Kg-m
3.0-4.7
2.5-3.5
5.0-6.0
1.3
4.5
2.5-4.0
0.8-1.2
1.0-1.6
2.2-3.5
1.8-2.8
0.2
1.8-2.8
SERVICING INFORMATION 7-25
TIGHTENING TORQUE CHART
Bolt Diameter
A (mm)
10
12
14
16
18
6
8
4
5
Conventional or W4W marked bolt
N-m Kg-m
1.5
3
0.15
0.3
6
13
29
45
0.6
1.3
2.9
4.5
65
105
160
6.5
10.5
16.0
Conventional bolt “4” marked bolt
10
23
50
85
N-m
“7” marked bolt
Kg-m
2
5
0.2
0.5
1.0
2.3
5.0
8.5
135
210
240
13.5
21.0
24.0
“7” marked bolt
7-26 SERVICING INFORMATION
SERVICE DATA
VALVE + GUIDE
ITEM
Valve diam.
Valve clearance (when cold)
Valve guide to valve stem
Clearance
Valve stem deflection
Valve guide I.D.
Valve stem O.D.
Valve stem run out
Valve head thickness
Valve stem end length
Valve seat width
Valve head radial run out
Valve spring free length
Valve spring tension
IN.
EX.
IN.
EX.
IN.
EX.
IN.&EX.
IN.&EX.
IN.
EX.
In. & EX.
In. & EX.
In. & EX.
In. & EX.
In. & EX.
In. & EX.
STANDARD
25
22
0.04-0.07
0.04-0.07
0.010-0.037
0.030-0.057
--------------
5.000-5.012
4.975-4.990
4.955-4.970
--------------
--------------
--------------
1.0
--------------
In. & EX.
14.7 N at length
25.8 mm.
CAMSHAFT + CYLINDER HEAD
Cam height.
ITEM
Rocker arm I.D.
Rocker arm shaft O.D.
Cylinder head distortion
IN.
EX.
IN. & EX.
IN. & EX.
STANDARD
27.61-27.71
27.42-27.52
10.003-10.018
--------------
9.981-9.990
CYLINDER + PISTON + PISTON RING
ITEM
Compression pressure
Piston to cylinder clearance
Cylinder bore
Piston diam.
Cylinder distortion
Piston ring free and gap
STANDARD
FD 110 XC / XCS / XCD / XCSD is a
14 kg/cm²
0.035-0.055
53.5-53.515
53.460-53.475
Measure at 11 from the skirt end.
1 st
1 nd
--------------
R
R
Approx. 6.5
Approx. 4.5
Unit: mm
LIMIT
27.34
27.150
--------------
--------------
0.050
Unit: mm
LIMIT
--------------
0.120
53.595
53.380
0.050
5.3
4.2
Unit: mm
LIMIT
--------------
--------------
--------------
--------------
--------------
--------------
0.350
--------------
--------------
--------------
0.050
0.500
2.400
--------------
0.030
30.090
--------------
SERVICING INFORMATION 7-27
ITEM
Piston ring end gap
Piston ring to groove clearance
Piston ring groove width
Piston ring thickness
1 st
2 nd
1 st
2 nd
1 st
2 nd
Oil
1 st
2 nd
STANDARD
0.10 – 0.25
0.10 – 0.25
-------------
-------------
1.01-1.03
14.002-14.008
13.996-14.00
1.01-1.03
2.01-2.03
0.97-0.99
0.97-0.99
Piston pin bore
Piston pin O.D.
CONROD + CRANKSHAFT
ITEM
Conrod small end I.D.
Conrod deflection
Conrod big end side clearance
Crank web to web width
Crankshaft thrust bearing thickness
Crankshaft thrust clearance
Crankshaft run out
OIL PUMP
ITEM
Oil pump reduction ration
Oil pressure (at 60°C)
STANDARD
14.006-14.014
--------------
0.10-0.45
42.0 ±0.1
0.60-1.35
0.00-0.07
--------------
STANDARD
1.824 (31/17)
Above 10 kPg (0.1 kg/cm
2
X
Below 30 kPg (0.3 kg/cm
2
) at
3,000 r/min.
FIRST CLUTCH
ITEM
Clutch release screw
Clutch heel I.D.
Clutch shoe O.D.
Clutch engagement
Clutch lock-up
GEAR SHIFT CLUTCH
ITEM
Drive plate thickness
Drive plate distortion
Drive plate claw width
No.1
STANDARD
1/8 turn back
105.00 – 105.15
--------------
1,900-2,300 r/min.
3,150-3,850 r/min
STANDARD
2.9-3.1
--------------
11.80-12.00
LIMIT
14.040
3.000
1.0
--------------
--------------
--------------
0.08
Unit: mm
LIMIT
0.500
0.500
0.180
0.150
-------------
-------------
-------------
-------------
-------------
14.030
13.960
Unit: mm
LIMIT
--------------
--------------
LIMIT
--------------
--------------
No groove
--------------
--------------
Unit: mm
Unit: mm
LIMIT
2.600 (No groove)
0.100
11.200
7-28 SERVICING INFORMATION
TRANSMISSION + DRIVE CHAIN
Shift fork to groove clearance
Shift fork groove width
Shift fork thickness
Drive chain
Drive chain slack
CARBURETOR
ITEM
Primary reduction ratio
Final reduction ratio
Gear ratios Low
2 nd
3 rd
Top
STANDARD
3.666 (77/21)
2.428 (34/14)
3.000 (33/11)
1.875 (30/16)
1.368 (26/19)
1.052 (20/19)
No. 1, No. 2 0.1-0.3
No. 1, No. 2
No. 1, No. 2
Type
4.5-4.6
4.3-4.4
DID428
Links
20-pitch length
15-25
98 links
--------------
Carburetor type
Bore size
I.D. No.
Idle r/min.
Float height
Main jet
Main air jet
Jet needle
Needle jet
Pilot jet
Pilot outlet
Air screw
Valve seat
Starter jet
ELECTRICAL
ITEM
Ignition timing
Spark plug
Spark performance
Ignition coil resistance
ITEM
(M.J.)
(M.A.J.)
(J.N.)
(N.J.)
(P.J.)
(P.O.)
(A.S.)
(V.S.)
(G.S.)
STANDARD
15° B.T.D.C. Below 1,500 r/min.
Type
Gap
NGK: CR6HSA
0.6-0.7 mm
Primary
Secondary
Over 8 at 1 atm.
(+) tap-Ground 0.3-1.1 Ω
Plug cap-Ground 11 – 18 k Ω
STANDARD
MIKUNI 17
17 mm
09GF1
1,500±100 r/min
16
#92.5
1.65
4PA11-2
E-OM
#15
07 mm
1 1/2 turns out
1.5 mm
#30
Unit: mm
LIMIT
--------------
--------------
--------------
--------------
--------------
--------------
0.50
--------------
--------------
--------------
--------------
259
--------------
Unit: mm
LIMIT
SERVICING INFORMATION 7-29
ITEM
Primary peak voltage
Pickup coil peak voltage
Magneto coil resistance
Regulated voltage
Battery
Morn then 130 V
STANDARD
(+)ground , (-)white/blue
Morn then 4 V (+)green/white , (-)blue/yellow
Lighting
Charging
Pick-up
Y/W – B/W 0.3 - 1.5 Ω
W/R – B/W 0.5 – 2.0 Ω
G/W-L/Y 180 – 280 Ω
13.0 – 16.0 V at 5,000 r/min
Capacity
Standard
Electrolytes S.G.
12V 5Ah/10HR
1.28 at 20°C
LIMIT
Night time
FD 110
Fuse side
WATTAGE
ITEM
Headlight
Tail/Brake light
Turn signal light
Turn signal indicator light
Speedometer light
High beam indicator light
Neutral indicator light
Gear position light
BRAKE + WHEEL
ITEM
Font brake lever play (drum type)
Rear brake pedal free ravel
Brake lining thickness
Brake disc thickness
Brake disc run out
Main
HI
LO
STANDARD
15.25
15.25
---------------
4±0.2
---------------
10A
STANDARD
32
32
5/18
10
1.7
3
1.7
1.7
1.7
LIMIT
---------------
---------------
1.5
3
0.30
7-30 SERVICING INFORMATION
BRAKE + WHEEL
ITEM
Master cylinder bore
Master cylinder piston diam.
Brake caliper cylinder bore
Brake caliper piston diam.
Brake drum I.D.
Wheel axle run out
Tire size
Tire tread depth
Front
Rear
Axle
Radial
Front
Rear
Front
Rear
STANDARD
12.700-12.743
12.657-12.684
27.00-27.050
2.930-26.50
---------------
---------------
---------------
---------------
2.50-17
2.75-17
---------------
---------------
SUSPENSION
ITEM
Front fork stroke
Rear wheel travel
Swing arm pivot shaft run out
STANDARD
90
77.9
---------------
LIMIT
---------------
---------------
0.6
NOTE
---------------
---------------
---------------
TIRE PRESSURE
COLD INFLATION
TIRE PRESSURE
FRONT
REAR
FUEL + OIL
ITEM
Fuel type
Psi
25
33
NORMAL AND DUAL RIDING
Kg/cm
2
Fuel tank capacity
Engine oil type
Engine oil capacity
Front fork oil type
Front fork oil capacity (each leg)
Brake fluid type
SPECIFICATION
Gasoline used should be graded 91 octane or higher. An unleaded gasoline is recommended.
4.2L
SAE 40, API SF or SG
Change 800 ml
Filter change
Overhaul
900 ml
1,000 ml
Fork oil # 10 or (SAE5W/20)
70 ml
DOT 4
1.75
2.80
NOTE
LIMIT
---------------
---------------
---------------
---------------
110.7
110.7
2.0
2.0
---------------
---------------
1.6
1.6

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- 110cc single-cylinder engine for reliable performance
- Lightweight and maneuverable chassis for easy handling
- Fuel-efficient engine and low maintenance costs