- Entertainment & hobby
- Musical instruments
- Musical Equipment
- EBS
- Stanley Clarke Pre Amp
- User's manual
advertisement
USERS MANUAL EBS STANLEY CLARKE PREAMP
EBS STANLEY CLARKE
SIGNATURE ACOUSTIC PREAMP
USERS MANUAL
w w w . e b s s w e d e n . c o m w w w . e b s s w e d e n . c o m
USERS MANUAL EBS STANLEY CLARKE PREAMP
CHANNEL CONTROLS, SWITCHES & OUTPUTS
MID. These two knobs works in conjunction. Use the left control to pick a frequency. Use the right control to boost or cut the gain in the range of the chosen frequency. The
MID-controls are identical on both channels.
MASTER controls the volume on the Output jack.
The balanced output (XLR) is not affected by the setting of this knob.
BASS is a 'shelving' type filter with a wide gain range. Identical on both channels.
PHASE. This switch inverts the phase of the A channel when needed.
MUTE FOOT SWITCH . Mutes the balanced outputs and the master output.
Fx Send is not affected by this function.
ELECTRET FUNCTION
This switch should be set to
OFF at all times, except when using an Electret pickup on the A channel (INPUT). w w w . e b s s w e d e n . c o m
CHANNEL CONTROLS, SWITCHES & OUTPUTS
w w w . e b s s w e d e n . c o m
EBS STANLEY CLARKE PREAMP USERS MANUAL
REFERENCE GUIDE
TYPE selects the function of the FILTER knob between High Pass or Notch (same function available on both the A and B channel).Default position is HP with the FILTER knob turned down to OFF.
SOURCE sets the input source for the B channel to either 1/4” (CH B Input) or XLR (MIC Input)
GAIN adjusts the input signal level. An optimum level is when the peak led starts flashing when playing hard on your instrument. A correctly set gain is vital for the signal processing to work properly.
TREBLE is a shelving type filter controlling the higher mids and treble registers, giving presence and ambiance to the sound. The TREBLE control is identical on both channels.
FILTER works in conjunction with the TYPE switch for each channel.
Choose between High Pass (HP) or Notch, and set the value with the Filter knob. Default position is the FILTER knob turned down to
Off and the Type switch set to HP.
Set the values individually for the
A and B channel.
A/B FOOT SWITCH
When A+B push switch is in its’ OUTER position:
Selects between A or B channel when only the A input (INPUT) is used.
If XLR input or B channel 1/4” jack is used at the same time, B selects this source.
When A+B push switch is in its’ INNER position:
Selects between A or A+B, i.e. either only A or
A in series with B channel when only A input is used. When B channel input jack is used or XLR is selected for channel B, both channels are mixed together and the A/B foot switch has no effect.
CONTINUED ON THE NEXT PAGE SPREAD >> w w w . e b s s w e d e n . c o m
USERS MANUAL EBS STANLEY CLARKE PREAMP
A
B/C
TUNER OUT. This output is taken at the FX send and can be used to connect to a tuner. This output becomes active when Mute is on.
FX LOOP. Connect a TRS cable, such as the EBS ICY-30, to B to create an
Effects Loop where you can insert your effects. C offer the choice to set the effects loop in parallel mode.
D OUTPUT. This is the master output jack to be connected to another amp or power amplifier.
A
B
C
D
E
F
G
E
F
G
CHANNEL B INPUT. This input is a direct input to the B channel or to both A+B if the A+B switch is in its’ inner position.
A+B. When A+B push switch is in its’ OUTER position:
Selects between A or B channel when only the A input (INPUT) is used.
If XLR input or B channel 1/4” jack is used at the same time, B selects this source.
When A+B push switch is in its’ INNER position:
Selects between A or A+B, i.e. either only A or A in series with B channel when only A input is used. When B channel input jack is used or XLR is selected for channel B, both channels are mixed together and the A/B foot switch has no effect.
INPUT - The A channel input is a low noise, high impedance instrument input. w w w . e b s s w e d e n . c o m
EBS STANLEY CLARKE PREAMP USERS MANUAL w w w . e b s s w e d e n . c o m
I
J
H
K
K
J
I
H
L
Note: The balanced output offers highquality ’line box’ signal for connecting to PA mixing consoles or to studio or broadcast recording units, with high noise immunity. The output level controlled by the MASTER knob does not affect this output.
------------
MIC INPUT. Makes possible to use a +48V Phantom microphone as the input for the B channel.
L
M
BAL OUT. This output sends a balanced output signal after the pedals equalizer.
N
Engage this switch to add an emulated
Speaker Simulation to the balanced output.
GND LIFT. Eliminates ground noise and hum. When required, press the
Gnd Lift switch to disconnect the ground from the balanced output.
M
N
AUX IN. Auxiliary input to be monitored only with headphones.
This input has no level control and the volume should be adjusted by the source.
PHONES. Connect your headphones here for silent practicing. The volume from the preamp is controlled by the MASTER knob where the Aux In level needs to be adjusted from the signal source.
DC INPUT. Connect the power supply here, only 9V DC, 1000 mA
(supplied in package).
w w w . e b s s w e d e n . c o m
USERS MANUAL EBS STANLEY CLARKE PREAMP
TECHNICAL SPECIFICATIONS
Channel Specifications:
Input Impedance:
Gain:
Bass Filter:
Mid Filter:
Treble Filter:
HP Filter:
Notch Filter:
Gain Range
Gain Peak LED
(ch A = RED, B = yellow)
Frequency Response
Type
Gain Range
Type
Gain Range
Frequency Range
Q
Type
Gain Range
Type
Frequency Range
Type
Frequency Range
Q
Attenuation
Electret Power (Channel A):
10 Mohms // 22 pF
-oo/+30 dB
+10 dBv
+0/-3 dB 20-20.000 Hz
Shelving
+/- 15 dB @ 40 Hz
Bandpass Filter
+/- 13 dB
70 - 2500 Hz
0.8
Shelving
+/- 15 dB @ 10 kHz
12 dB/octave High Pass
20(off) - 450 Hz
Bandpass Notch
70 - 2200 Hz
7
7 dB (typically)
5V, 2mA
FOR MORE PEDALS, AMPS &
ACCESSORIES, SCAN THE QR-CODE TO VISIT
WWW.EBSSWEDEN.COM
w w w . e b s s w e d e n . c o m
TECHNICAL SPECIFICATIONS
w w w . e b s s w e d e n . c o m
EBS STANLEY CLARKE PREAMP USERS MANUAL
Common Features:
Effects Loop:
Phones Out:
Aux Input:
Output:
Balanced Output:
Loop Signal Level
Gain
Output Impedance
Input Impedance
Modes
Recommended Imp.
Input Impedance
Nominal Level
Output Impedance
Signal Level
Output Level
XLR Connections
Options
Balanced Input (Channel B): Input Level
XLR Connections
48V Phantom
Auxiliary Info:
Power Requirements Idle max
Dimensions (WxDxH):
Weight: max
660 g
Specifications are subject to change without notice.
-10 dBv (nominal)
Unity (1:1)
2 kohms
100 kohms
Serial or Parallel
32 - 200 ohms
20 kohms
-10 dBv
<1 kohms
0 dBv (nominal)
-20dBv (nominal)
1-GND, 2-Hot, 3-Cold
Gnd Lift, SPKR Sim
-30dBv (nominal)
1-GND, 2-Hot, 3-Cold
Yes
500mA @9V
800mA @9V
(with headphones at max output level)
168 x 124 x 53 mm /
6.6” x 4.9” x 2.1”
(1.5 lbs.) w w w . e b s s w e d e n . c o m
USERS MANUAL EBS STANLEY CLARKE PREAMP
FOOT SWITCH
EFFECTS LOOP (-10 dBv)
BALANCED OUTPUT
Parallel Mode
MUTE FOOT SWITCH
5 V 2 mA
MICROPHONE INPUT w w w . e b s s w e d e n . c o m
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project