Gilson Vortex Mixer User Manual
Gilson Vortex Mixer is a quiet, powerful mixer ideal for vortexing micro tubes of various sizes. Its dynamic balance technology ensures smooth, quiet operation with low vibration. It features an electronic speed control allowing you to set the mixing speed between 200 and 3200 rpm. Choose between continuous ON mode, OFF, or TOUCH mix mode for momentary mixing. The standard rubber cup head can be easily removed and replaced, and additional accessory heads are available for specific applications. With suction cup feet, the mixer stays securely in place during use.
Advertisement
Advertisement
Vortex Mixer
User’s Guide
EN
2
Trademarks
All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of the trademark(s) in this document does not imply any affiliation with or endorsements by the trademark holder(s).
| Vortex Mixer Vortex Mixer | USer’S GUiDe
| Vortex Mixer
TABLE OF CONTENTS
installation | 5 operation | 5
Head removal and replacement | 5
Vortex Mixer | USer’S GUiDe 3
Introduction
the Vortex Mixer is a quiet, powerful, mixer designed for vortexing micro tubes of all sizes (0.4 mL to 50 mL, and larger). it combines dynamic balance technology with an electronic speed control to provide smooth speed and quiet operation with low excess vibration. this vortex mixer will provide years of reliable service.
Specifications
Vortex Mixer
Speed/Control
Operating Modes
Head
Feet
Orbit
Operating Environment
Dimensions (WxDxH)
Weight
Electrical
Warranty
User settable 200 to 3200 rpm
ON (continuous), OFF, and TOUCH mix
Standard rubber cup (Vortexer Flat head
PN 36117310)
Four suction cups
3 mm
4°C to 45°C
13 x 16 x 17 cm / 5.1 x 6.2 x 6.6 in.
3.8 kg / 8.4 lbs.
115VAC, 60 Hz, 1.5 amps (115V model)
230VAC, 50 Hz, 0.75 amps, (230V model)
2 years
4 introDUction | Vortex Mixer Vortex Mixer | USer’S GUiDe
introDUction | Vortex Mixer
Installation
1. Place the Vortex Mixer on a clean, flat, stable surface and press down slightly to allow the suction cup feet to adhere.
2. Make sure that the mode switch is in the oFF position and plug the vortex mixer into a properly grounded outlet.
3. Using the speed control knob, adjust the mixing speed to the desired setting.
4. check that the cup head is securely fastened by gently rotating it clockwise.
5. Start at the middle of the speed range if you are uncertain of what setting you need.
Operation
in touch mode, the tube to be mixed is pressed downward against the head to activate the vortex mixing action.
NOTICE
Avoid the use of solvents as they may attack the rubber cup head or the acrylonitrile butadience styreme (ABS) plastic housing.
Head Removal and Replacement
to change or replace the rubber head attachment, grasp the unit body with your left hand, and then gently rotate the head attachment counter clockwise with your right hand until the cup head is completely unscrewed. replace the head attachment by gently rotating clockwise until it is tight and you feel the rubber start to grip the top of the dynamic drive assembly.
NOTE
Attaching accessory heads requires the use of a Phillips screwdriver to tighten the center screw in the accessory head.
Vortex Mixer | USer’S GUiDe 5
Ordering Information
PArt nUMBer
DeScriPtion
36110740
36110750
36110760
36110770
Vortex Mixer with standard cup head, 115V, US cord
Vortex Mixer with standard cup head, 230V, EU cord (3-pin cord)
Vortex Mixer with standard cup head, 230V, UK cord
Vortex Mixer with standard cup head, 230V, AU cord
Accessories
Accessory heads are available. Please contact a Gilson Service center if you need one of these accessory heads.
PArt nUMBer
36117310
DeScriPtion
36117330
36117340
36117350
36117360
36117370
Vortexer Flat head
Optional Foam Rack for 12 tubes (15 mL)
For Vortex Mixer with standard cup head only
(PN 36110740)
Optional Foam Rack for 5 tubes (50 mL)
For Vortex Mixer with standard cup head only
(PN 36110740)
Horizontal head, for 12 x 1.5 mL
Horizontal head, for 4 x 15 mL
Horizontal head, for 2 x 50 mL
6 orDerinG inForMAtion | Vortex Mixer Vortex Mixer | USer’S GUiDe
Warranty
Gilson warrants this instrument against defects in material under normal use and service for two years from the date of purchase. this warranty is valid only if the instrument is used in the manner described in this guide and for the purpose for which it is designed. Gilson is not responsible for consequential damages resulting from the misuse or bad cleaning or decontamination of this instrument. enclose with the returned instrument a description of the problem that has occurred.
orDerinG inForMAtion | Vortex Mixer Vortex Mixer | USer’S GUiDe 7
Specifications subject to change without notification — errors excepted. reproduction, adaptation, or translation without prior written permission is prohibited, except as allowed under copyright laws.
www.gilson.com/contactus
Lt318403-01 | ©2018 Gilson, inc. All rights reserved.

Public link updated
The public link to your chat has been updated.
Advertisement