Gecko in.k400 Keypad Quick Start Card

Show HTML Add to My manuals
1 Pages

advertisement

Gecko in.k400 Keypad Quick Start Card | Manualzz

Quick Reference Card in.xm

in.k400

Series of compact full-function keypads for in.xm spa systems

Aeware’s new series of keypads features a large LCD display and raised keys that let users control all in.xm functions and programming directly from spa side. In.k400 comes in an easy to install waterproof plastic enclosure and is designed to maximize user experience.

Spa Functions

On/Off key

Depending on the spa manufacturer, this key may have different functions:

On/Off, Standby mode or quick enable of the Economy mode.

Standby Mode : Use On/Off key to pause all pumps*.

Progress bar will display the remaining time before the system automatically exits

Standby mode (user can also exit Standby mode at any time by pressing again on

On/Off key).

In order to warn the user, the spa light will flash for a few seconds before the exit of

Standby mode and restart the pumps. The "Stby" message is also displayed during

Standby mode.

* Pump will stay turned on if there is a request for more heat.

Pump 1 key

Press Pump 1 key to turn

Pump 1 on at low speed.

Press a second time to turn pump to high speed (with a dual-speed pump). A third time turns pump off.

A built-in timer automatically turns pump off after 20 minutes, unless pump has been manually deactivated first.

Pump 2 key

Press Pump 2 key to turn

Pump 2 on at low speed.

Press a second time to turn pump to high speed (with a dual-speed pump). A third time turns pump off.

A built-in timer automatically turns pump off after 20 minutes, unless pump has been manually deactivated first.

* If single speed pump: press Pump key to turn pump on.

Press Pump key again to turn pump off.

Programming Steps

Pump 3 key

Press Pump 3 key to turn

Pump 3 on. Press a second time to turn pump off.

A built-in timer automatically turns pump off after 20 minutes, unless pump has been manually deactivated first.

Note: option available in certain models only.

Light key

Press Light key to turn light on at high intensity. Subsequent presses change light intensity.

A last press turns light off.

A built-in timer automatically turns light off after 2 hours, unless it has been manually deactivated first.

Up/Down keys

Use Up or Down key to set desired water temperature.

The temperature setting will be displayed for 5 seconds to confirm your new selection.

The "Set Point" icon indicates that the display shows the desired temperature,

NOT the current water temperature!

Program key

Use Program key to display time or enter Programming menu by pressing and holding key. In Programming mode, the following parameters can be set: time, filter cycle start time, filter cycle duration, filter cycle frequency, and temperature unit.

Note: Light key is used as

Program key if this key is not present.

Setting the time

Enter Programming mode by holding Prog. key pressed down for 3 sec. The display will show the current time setting.

Setting the hour: Use Up or

Down arrows to change hour setting (AM/PM) .

Setting the minutes: Press

Prog . key a second time.

Use Up or Down key to change hour setting.

Setting filter cycle start time

To program the filter cycle, you must enter these parameters: the start time, duration and frequency.

During a filter cycle, pumps run for one minute to purge the plumbing, then Pump

1 runs for the programmed number of hours.

Press Prog . key a third time.

The display will show FSxx , with "xx" representing the starting hour. Use Up or

Down key to change setting.

Setting filter cycle duration

Press Prog . key a fourth time.

The display will show Fdxx , with "xx" representing the duration in hours.

Use Up or Down key to change setting.

Filter cycle frequency

Press Prog . key a fifth time.

The display will show FFxx , with "xx" representing the number of filter cycles per day

(up to 4).

Use Up or Down key to change setting.

Setting economy mode

This mode allows you to lower the temperature set point of the spa by 20 °F

(11 °C) during a certain period of the day.

Press Prog . key a sixth time.

Use Up key to enable the economy mode, the display will show EP 1 or use Down key to disable economy mode, the display will show

EP 0.

Setting economy start time

Press Prog . key an seventh time. The display will show

ES xx, with “xx” representing the starting hour.

Use Up or Down key to change setting.

Setting economy end time

Press Prog . key a eighth time.

The display will show EE xx, with “xx” representing the ending time in hour.

Use Up or Down key to change setting.

Cooldown

Setting temperature unit

Water temperature can be displayed in either Fahrenheit

(˚F) or Celsius (˚C). Press Prog . key a ninth time. The display will show either ˚F or ˚C.

Use Up or Down key to change setting.

Press Prog. key once more to go back to normal mode.

Smart Winter Mode

Our Smart Winter Mode protects your system from the cold by turning pumps on several times a day to prevent water from freezing in pipes.

After heating the spa water to the desired Set Point, the heater is turned off, but its associated pump (Pump 1 Low-speed or CP) remains on for a predetermined period of time to ensure adequate cooling of the heating element, this prolongs its useful life. The heater icon flashes during this time.

Water temperature regulation

In a regulation cycle, the system first generates water flow through the heater housing and the plumbing, in order to ensure accurate water temperature readings as well as avoiding heater activation in dry conditions.

After verifying pump activation and taking a water temperature reading if required, the system automatically turns the heater on to reach and maintain water temperature at Set Point.

9919-100674-C www.geckoalliance.com

advertisement

Key Features

  • Waterproof design
  • Large LCD display
  • Raised keys for easy operation
  • Control all in.xm spa functions
  • Intuitive programming menu
  • Filter cycle management
  • Economy mode
  • Smart Winter Mode
  • Temperature unit selection
  • Cooldown feature

Related manuals

Frequently Answers and Questions

How do I set the water temperature?
Use the Up or Down keys to adjust the desired water temperature. The new setting will be displayed for 5 seconds to confirm your selection. Remember, the 'Set Point' icon indicates the desired temperature, not the current water temperature.
How do I program the filter cycle?
Press the 'Prog' key repeatedly to access the filter cycle settings. You can then adjust the start time, duration, and frequency using the Up or Down keys. During a filter cycle, the pumps will run for one minute to purge the plumbing, followed by Pump 1 running for the programmed duration.
What is the Economy Mode, and how do I enable it?
Economy Mode allows you to reduce energy consumption by lowering the spa temperature during certain periods. To enable it, press the 'Prog' key six times, then use the Up key. The display will show 'EP 1' to indicate Economy Mode is active. To disable it, use the Down key, and the display will show 'EP 0'.
Download PDF

advertisement